ON MC10EP139DTR2G Clock generation chip Datasheet

MC10EP139, MC100EP139
3.3V / 5V ECL ÷2/4, ÷4/5/6
Clock Generation Chip
Description
The MC10/100EP139 is a low skew ÷2/4, ÷4/5/6 clock generation chip
designed explicitly for low skew clock generation applications. The
internal dividers are synchronous to each other, therefore, the common
output edges are all precisely aligned.
The common enable (EN) is synchronous so that the internal dividers
will only be enabled/disabled when the internal clock is already in the
LOW state. This avoids any chance of generating a runt clock pulse on
the internal clock when the device is enabled/disabled as can happen with
an asynchronous control. The internal enable flip-flop is clocked on the
falling edge of the input clock, therefore, all associated specification
limits are referenced to the negative edge of the clock input.
Upon start-up, the internal flip-flops will attain a random state;
therefore the master reset (MR) input may require assertion to ensure
system synchronization. Internal divider design ensures synchronization
between the ÷2/4 and the ÷4/5/6 outputs within a device. All VCC and
VEE pins must be externally connected to power supply to guarantee
proper operation.
The VBB Pin, an internally generated voltage supply, is available to this
device only. For Single-Ended input conditions, the unused differential
input is connected to VBB as a switching reference voltage. VBB may also
rebias AC coupled inputs. When used, decouple VBB and VCC via a
0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When
not used, VBB should be left open.
The 100 Series contains temperature compensation.
Features
• Maximum Frequency = > 1.0 GHz Typical
• 50 ps Output-to-Output Skew
• PECL Mode Operating Range:
•
•
•
•
•
•
•
August, 2016 − Rev. 14
1
1
TSSOP−20 WB
DT SUFFIX
CASE 948E
SOIC−20 WB
DW SUFFIX
CASE 751D
QFN−20
MN SUFFIX
CASE 485E
MARKING DIAGRAMS*
20
20
HEP or KEP
139
ALYWG
G
TSSOP−20 WB
MCXXXEP139
AWLYYWWG
1
HEP
KEP
XXX
A
L,WL
Y, YY
W, WW
G or G
1
SOIC−20 WB
XXXX
EP139
ALYWG
G
QFN−20
= MC10EP
= MC100EP
= 10 or 100
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb-Free Package
(Note: Microdot may be in either location)
VCC = 3.0 V to 5.5 V with VEE = 0 V
NECL Mode Operating Range:
VCC = 0 V with VEE = −3.0 V to −5.5 V
Open Input Default State
Safety Clamp on Inputs
Synchronous Enable/Disable
Master Reset for Synchronization of Multiple Chips
VBB Output
These Devices are Pb-Free, Halogen Free and are RoHS Compliant
© Semiconductor Components Industries, LLC, 2016
www.onsemi.com
1
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
Publication Order Number:
MC10EP139/D
MC10EP139, MC100EP139
VCC
1
20
VCC
EN
2
19
Q0
Table 1. PIN DESCRIPTION
PIN
FUNCTION
CLK*, CLK*
ECL Differential Clock Inputs
EN*
ECL Sync Enable
MR*
ECL Master Reset
VBB
ECL Reference Output
Q0, Q1, Q0, Q1
ECL Differential B2/4 Outputs
Q2, Q3, Q2, Q3
ECL Differential B4/5/6 Outputs
DIVSELa*
ECL Frequency Select Input B2/4
DIVSELb0
3
18
Q0
CLK
4
17
Q1
CLK
5
16
Q1
VBB
6
15
Q2
MR
7
14
Q2
VCC
8
13
Q3
DIVSELb1
9
12
Q3
DIVSELb0*
ECL Frequency Select Input B4/5/6
10
11
VEE
DIVSELb1*
ECL Frequency Select Input B4/5/6
VCC
ECL Positive Supply
VEE
ECL Negative Supply
EP
Exposed Pad
Warning: All VCC and VEE pins must be externally connected to
a Power Supply to guarantee proper operation.
Figure 1. 20-Lead Pinout (Top View)
*Pins will default low when left open.
EN
VCC
VCC
Q0
Q0
Exposed Pad
20
19
18
17
16
DIVSELb0
1
15
Q1
CLK
2
14
Q1
CLK
3
13
Q2
VBB
4
12
Q2
MR
5
11
Q3
7
8
9
DIVSELa
VEE
VCC
6
DIVSELb1
MC10/100EP139
10
Q3
DIVSELa
MC10/100EP139
Warning: All VCC and VEE pins must be externally connected to a Power Supply to
guarantee proper operation.
The Exposed Pad (EP) on package bottom must be attached to a heat-sinking conduit. The Exposed Pad may only be electrically connected to VEE.
Figure 2. QFN-20 Pinout (Top View)
www.onsemi.com
2
MC10EP139, MC100EP139
DIVSELa
Q0
CLK
÷2/4
CLK
R
Q0
Q1
Q1
Q2
EN
÷4/5/6
R
Q2
Q3
MR
DIVSELb0
DIVSELb1
Q3
VEE
Figure 3. Logic Diagram
Table 2. FUNCTION TABLES
CLK
EN
MR
Function
Z
ZZ
X
L
H
X
L
L
H
Divide
Hold Q0:3
Reset Q0:3
Z = Low-to-High Transition
ZZ = High-to-Low Transition
DIVSELa
Q0:1 Outputs
L
H
Divide by 2
Divide by 4
DIVSELb0
DIVSELb1
Q2:3 Outputs
L
H
L
H
L
L
H
H
Divide by 4
Divide by 6
Divide by 5
Divide by 5
CLK
Q (÷2)
Q (÷4)
Q (÷5)
Q (÷6)
Figure 4. CLK and OUTPUT Timing Diagram
CLK
tRR
RESET
Q (÷n)
Figure 5. Timing Diagram
www.onsemi.com
3
MC10EP139, MC100EP139
Table 3. ATTRIBUTES
Characteristics
Value
Internal Input Pulldown Resistor
75 kW
Internal Input Pullup Resistor
N/A
ESD Protection
Human Body Model
Machine Model
Charged Device Model
> 2 kV
> 100 V
> 2 kV
Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1)
Pb-Free Pkg
SOIC−20 WB
TSSOP−20 WB
QFN−20
Flammability Rating
Level 3
Level 1
Level 1
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
Transistor Count
758 Devices
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. For additional information, see Application Note AND8003/D.
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
6
V
−6
V
6
−6
V
50
100
mA
±0.5
mA
VCC
PECL Mode Power Supply
VEE = 0 V
VEE
NECL Mode Power Supply
VCC = 0 V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
Iout
Output Current
Continuous
Surge
IBB
VBB Sink/Source
TA
Operating Temperature Range
−40 to +85
°C
Tstg
Storage Temperature Range
−65 to +150
°C
qJA
Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
TSSOP−20 WB
TSSOP−20 WB
140
100
°C/W
qJC
Thermal Resistance (Junction-to-Case)
Standard Board
TSSOP−20 WB
23 to 41
°C/W
qJA
Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
SOIC−20 WB
SOIC−20 WB
90
60
°C/W
qJC
Thermal Resistance (Junction-to-Case)
Standard Board
SOIC−20 WB
33 to 35
°C/W
qJA
Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
QFN−20
QFN−20
47
33
°C/W
qJC
Thermal Resistance (Junction-to-Case)
Standard Board
QFN−20
18
°C/W
Tsol
Wave Solder (Pb-Free)
< 2 to 3 sec @ 260°C
265
°C
VI ≤ VCC
VI ≥ VEE
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
www.onsemi.com
4
MC10EP139, MC100EP139
Table 5. 10EP DC CHARACTERISTICS, PECL (VCC = 3.3 V, VEE = 0 V (Note 1))
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
65
82
105
65
83
105
65
84
105
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
2165
2290
2415
2230
2355
2480
2290
2415
2540
mV
VOL
Output LOW Voltage (Note 2)
1365
1490
1615
1430
1555
1680
1490
1615
1740
mV
VIH
Input HIGH Voltage (Single-Ended)
2090
2415
2155
2480
2215
2540
mV
VIL
Input LOW Voltage (Single-Ended)
1365
1690
1460
1755
1490
1815
mV
VBB
Output Voltage Reference
1790
1990
1855
2055
1915
2115
mV
3.3
2.0
3.3
2.0
3.3
V
150
mA
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
IIH
Input HIGH Current
IIL
Input LOW Current
1890
2.0
1955
150
0.5
2015
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
2. All loading with 50 W to VCC − 2.0 V (see Figure 10).
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 6. 10EP DC CHARACTERISTICS, PECL (VCC = 5.0 V, VEE = 0 V (Note 1))
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
65
82
105
65
83
105
65
84
105
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
3865
3990
4115
3930
4055
4180
3990
4115
4240
mV
VOL
Output LOW Voltage (Note 2)
3065
3190
3315
3130
3255
3380
3190
3315
3440
mV
VIH
Input HIGH Voltage (Single-Ended)
3790
4115
3855
4180
3915
4240
mV
VIL
Input LOW Voltage (Single-Ended)
3065
3390
3130
3455
3190
3515
mV
VBB
Output Voltage Reference
3490
3690
3555
3755
3615
3815
mV
5.0
2.0
5.0
2.0
5.0
V
150
mA
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
IIH
Input HIGH Current
IIL
Input LOW Current
3590
2.0
150
0.5
3655
150
0.5
0.5
3715
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
2. All loading with 50 W to VCC − 2.0 V (see Figure 10).
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
www.onsemi.com
5
MC10EP139, MC100EP139
Table 7. 10EP DC CHARACTERISTICS, NECL (VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 1))
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
65
82
105
65
83
105
65
84
105
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
−1135
−1010
−885
−1070
−945
−820
−1010
−885
−760
mV
VOL
Output LOW Voltage (Note 2)
−1935
−1810
−1685
−1870
−1745
−1620
−1810
−1685
−1560
mV
VIH
Input HIGH Voltage (Single-Ended)
−1210
−885
−1145
−820
−1085
−760
mV
VIL
Input LOW Voltage (Single-Ended)
−1935
−1610
−1870
−1545
−1810
−1485
mV
VBB
Output Voltage Reference
−1510
−1310
−1445
−1245
−1385
−1185
mV
0.0
V
150
mA
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
IIH
Input HIGH Current
IIL
Input LOW Current
−1410
VEE+2.0
0.0
−1345
VEE+2.0
0.0
150
0.5
−1285
VEE+2.0
150
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC.
2. All loading with 50 W to VCC − 2.0 V (see Figure 10).
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 8. 100EP DC CHARACTERISTICS, PECL (VCC = 3.3 V, VEE = 0 V (Note 1))
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
70
83
100
70
87
105
75
90
110
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
2155
2280
2405
2155
2280
2405
2155
2280
2405
mV
VOL
Output LOW Voltage (Note 2)
1305
1480
1605
1305
1480
1605
1305
1480
1605
mV
VIH
Input HIGH Voltage (Single-Ended)
2075
2420
2075
2420
2075
2420
mV
VIL
Input LOW Voltage (Single-Ended)
1305
1675
1305
1675
1305
1675
mV
VBB
Output Voltage Reference
1725
1925
1725
1925
1725
1925
mV
3.3
2.0
3.3
2.0
3.3
V
150
mA
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
IIH
Input HIGH Current
IIL
Input LOW Current
1825
2.0
150
0.5
1825
150
0.5
0.5
1825
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
2. All loading with 50 W to VCC − 2.0 V (see Figure 10).
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
www.onsemi.com
6
MC10EP139, MC100EP139
Table 9. 100EP DC CHARACTERISTICS, PECL (VCC = 5.0 V, VEE = 0 V (Note 1))
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
70
85
100
70
90
105
75
95
110
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
3855
3980
4105
3855
3980
4105
3855
3980
4105
mV
VOL
Output LOW Voltage (Note 2)
3005
3180
3305
3005
3180
3305
3005
3180
3305
mV
VIH
Input HIGH Voltage (Single-Ended)
3775
4120
3775
4120
3775
4120
mV
VIL
Input LOW Voltage (Single-Ended)
3005
3375
3005
3375
3005
3375
mV
VBB
Output Voltage Reference
3425
3625
3425
3625
3425
3625
mV
5.0
2.0
5.0
2.0
5.0
V
150
mA
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
IIH
Input HIGH Current
IIL
Input LOW Current
3525
2.0
3525
150
3525
150
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
2. All loading with 50 W to VCC − 2.0 V (see Figure 10).
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 10. 100EP DC CHARACTERISTICS, NECL (VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 1))
−40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
70
85
100
70
90
105
75
95
110
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
−1145
−1020
−895
−1145
−1020
−895
−1145
−1020
−895
mV
VOL
Output LOW Voltage (Note 2)
−1995
−1820
−1695
−1995
−1820
−1695
−1995
−1820
−1695
mV
VIH
Input HIGH Voltage (Single-Ended)
−1225
−880
−1225
−880
−1225
−880
mV
VIL
Input LOW Voltage (Single-Ended)
−1995
−1625
−1995
−1625
−1995
−1625
mV
VBB
Output Voltage Reference
−1575
−1375
−1575
−1375
−1575
−1375
mV
0.0
V
150
mA
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
IIH
Input HIGH Current
IIL
Input LOW Current
−1475
VEE+2.0
0.0
VEE+2.0
150
0.5
−1475
0.0
VEE+2.0
150
0.5
−1475
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC.
2. All loading with 50 W to VCC − 2.0 V (see Figure 10).
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
www.onsemi.com
7
MC10EP139, MC100EP139
Table 11. AC CHARACTERISTICS (VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 1))
−40°C
Symbol
Characteristic
Min
Typ
fmax
Maximum Frequency
(See Figures 6, 7, 8 and 9 Fmax
/JITTER)
tPLH,
tPHL
Propagation Delay
CLK, Q (Diff)
MR, Q
550
700
700
800
tRR
Reset Recovery
200
ts
Setup Time
EN, CLK
DIVSEL, CLK
th
tPW
Typ
750
850
100
200
200
400
120
180
Hold Time
CLK, EN
CLK, DIVSEL
100
200
Minimum Pulse Width
MR
550
Q, Q
tJITTER
Random Clock Jitter (RMS)
(See Figures 6, 7, 8 and 9 Fmax/JITTER)
Input Voltage Swing (Differential Configuration)
Output Rise/Fall Times
Q, Q (20%−80%)
85°C
Max
Min
>1
600
700
Within Device Skew
Device-to-Device Skew (Note 2)
tr
tf
Min
>1
tSKEW
VPP
25°C
Max
800
900
Typ
Max
>1
900
1000
675
800
825
950
100
200
100
200
400
120
180
200
400
120
180
50
140
100
200
50
140
100
200
50
140
450
550
450
550
450
Unit
GHz
975
1100
ps
ps
ps
ps
ps
50
200
100
300
50
200
100
300
50
200
100
300
ps
0.2
< 1.0
0.2
< 1.0
0.2
< 1.5
ps
150
800
1200
150
800
1200
150
800
1200
mV
110
180
250
125
190
275
150
215
300
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V (see Figure 10).
2. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays
are measured from the cross point of the inputs to the cross point of the outputs.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
8
900
8
800
7
700
6
600
5
500
4
400
3
300
2
200
(JITTER)
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉ
ÉÉ
1
100
0
JITTEROUT ps (RMS)
VOUTpp (mV)
MC10EP139, MC100EP139
0
200
400
600
800
1000
1200
1400
1600
1800
2000
FREQUENCY (MHz)
900
8
800
7
700
6
600
5
500
4
400
3
300
2
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
200
(JITTER)
1
100
0
0
200
400
600
800
1000
1200
1400
FREQUENCY (MHz)
Figure 7. B5, Fmax/Jitter
www.onsemi.com
9
1600
1800
2000
JITTEROUT ps (RMS)
VOUTpp (mV)
Figure 6. B2, Fmax/Jitter
ÉÉ
ÉÉ
ÉÉ
900
8
800
7
700
6
600
5
500
4
400
3
300
2
200
(JITTER)
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉ
ÉÉ
1
100
0
JITTEROUT ps (RMS)
VOUTpp (mV)
MC10EP139, MC100EP139
0
200
400
600
800
1000
1200
1400
1600
1800
2000
FREQUENCY (MHz)
900
8
800
7
700
6
600
5
500
4
400
3
300
2
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
200
(JITTER)
1
100
0
0
200
400
600
800
1000
1200
1400
1600
1800
2000
FREQUENCY (MHz)
Figure 9. B6, Fmax/Jitter
Q
Zo = 50 W
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = VCC − 2.0 V
Figure 10. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices)
www.onsemi.com
10
JITTEROUT ps (RMS)
VOUTpp (mV)
Figure 8. B4, Fmax/Jitter
ÉÉ
ÉÉ
ÉÉ
MC10EP139, MC100EP139
ORDERING INFORMATION
Package
Shipping†
MC10EP139DTG
TSSOP−20 WB
(Pb-Free)
75 Units / Tube
MC10EP139DTR2G
TSSOP−20 WB
(Pb-Free)
2500 / Tape & Reel
MC10EP139DWG
SOIC−20 WB
(Pb-Free)
38 Units / Tube
MC10EP139DWR2G
SOIC−20 WB
(Pb-Free)
1000 / Tape & Reel
MC100EP139DTG
TSSOP−20 WB
(Pb-Free)
75 Units / Tube
MC100EP139DTR2G
TSSOP−20 WB
(Pb-Free)
2500 / Tape & Reel
MC100EP139DWG
SOIC−20 WB
(Pb-Free)
38 Units / Tube
MC100EP139DWR2G
SOIC−20 WB
(Pb-Free)
1000 / Tape & Reel
MC100EP139MNG
QFN−20
(Pb-Free)
92 Units / Tube
MC100EP139MNTXG
QFN−20
(Pb-Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
www.onsemi.com
11
MC10EP139, MC100EP139
PACKAGE DIMENSIONS
TSSOP−20 WB
CASE 948E
ISSUE D
20X
0.15 (0.006) T U
2X
L
K REF
0.10 (0.004)
S
L/2
20
M
T U
S
V
ÍÍÍÍ
ÍÍÍÍ
ÍÍÍÍ
K
K1
S
J J1
11
B
SECTION N−N
−U−
PIN 1
IDENT
0.25 (0.010)
N
1
10
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
N
F
DETAIL E
−W−
C
G
D
H
DETAIL E
0.100 (0.004)
−T− SEATING
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
PLANE
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
www.onsemi.com
12
MILLIMETERS
MIN
MAX
6.40
6.60
4.30
4.50
--1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.27
0.37
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.252
0.260
0.169
0.177
--0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.011
0.015
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
MC10EP139, MC100EP139
PACKAGE DIMENSIONS
SOIC−20 WB
CASE 751D−05
ISSUE H
A
20
q
X 45 _
M
E
h
0.25
1
10
20X
B
b
0.25
M
T A
S
B
DIM
A
A1
b
c
D
E
e
H
h
L
q
S
A
L
H
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF B
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
11
B
M
D
18X
e
A1
SEATING
PLANE
c
T
RECOMMENDED
SOLDERING FOOTPRINT*
20X
20X
1.30
0.52
20
11
11.00
1
10
1.27
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
13
MILLIMETERS
MIN
MAX
2.35
2.65
0.10
0.25
0.35
0.49
0.23
0.32
12.65
12.95
7.40
7.60
1.27 BSC
10.05
10.55
0.25
0.75
0.50
0.90
0_
7_
MC10EP139, MC100EP139
PACKAGE DIMENSIONS
QFN−20, 4x4, 0.5P
CASE 485E−01
ISSUE B
A
B
D
PIN ONE
REFERENCE
2X
0.15 C
ÉÉÉ
ÉÉÉ
ÇÇ
ÇÇ
ÉÉ
EXPOSED Cu
E
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND 0.30 MM
FROM THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED PAD
AS WELL AS THE TERMINALS.
ÉÉ
ÇÇ
ÉÉ
A3
MOLD CMPD
A1
DETAIL B
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
OPTIONAL CONSTRUCTIONS
2X
0.15 C
L
TOP VIEW
(A3)
DETAIL B
L
L1
A
0.10 C
DETAIL A
OPTIONAL CONSTRUCTIONS
0.08 C
A1
SIDE VIEW
C
MILLIMETERS
MIN
MAX
0.80
1.00
--0.05
0.20 REF
0.20
0.30
4.00 BSC
2.60
2.90
4.00 BSC
2.60
2.90
0.50 BSC
0.20 REF
0.35
0.45
0.00
0.15
SEATING
PLANE
SOLDERING FOOTPRINT*
4.30
0.10 C A B
D2
DETAIL A
20X
6
20X
0.58
L
2.88
0.10 C A B
11
E2
1
1
K
20
e
2.88 4.30
20X
b
0.10 C A B
0.05 C
PKG
OUTLINE
NOTE 3
BOTTOM VIEW
20X
0.35
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
14
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10EP139/D
Similar pages