Click on Series name for product info on aimtec.com Series AM3G-NZ 3 Watt | DC-DC Converter FEATURES: 1500 and 3000VDC I/O Isolation Very low no load consumption Remote On/Off Control 8 pin SIP package Operating temperature -40oC to 100oC Continuous Short circuit protection Wide 2:1 input range High efficiency up to 84% Models Single output Model Input Voltage (V) Output Voltage(V) Output Current max (mA) Isolation (VDC) Capacitor Load (μF) Efficiency (%) AM3G-0505S-NZ AM3G-0509S-NZ AM3G-0512S-NZ AM3G-0515S-NZ AM3G-1203S-NZ AM3G-1205S-NZ AM3G-1209S-NZ AM3G-1212S-NZ AM3G-1215S-NZ AM3G-1224S-NZ AM3G-2403S-NZ AM3G-2405S-NZ AM3G-2409S-NZ AM3G-2412S-NZ AM3G-2415S-NZ AM3G-2424S-NZ AM3G-4803S-NZ AM3G-4805S-NZ AM3G-4812S-NZ AM3G-4815S-NZ AM3G-4824S-NZ AM3G-0505SH30-NZ AM3G-0509SH30-NZ AM3G-0512SH30-NZ AM3G-0515SH30-NZ AM3G-1203SH30-NZ AM3G-1205SH30-NZ AM3G-1209SH30-NZ AM3G-1212SH30-NZ AM3G-1215SH30-NZ AM3G-1224SH30-NZ AM3G-2403SH30-NZ AM3G-2405SH30-NZ AM3G-2409SH30-NZ AM3G-2412SH30-NZ AM3G-2415SH30-NZ AM3G-2424SH30-NZ AM3G-4803SH30-NZ AM3G-4805SH30-NZ AM3G-4812SH30-NZ AM3G-4815SH30-NZ 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 5 9 12 15 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 12 15 24 5 9 12 15 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 12 15 500 278 208 167 758 600 333 250 200 125 758 600 333 250 200 125 758 600 250 200 125 500 278 208 167 758 600 333 250 200 125 758 600 333 250 200 125 758 600 250 200 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 2200 1000 680 470 2700 2200 1000 680 470 330 2700 2200 1000 680 470 330 2700 2200 680 470 330 2200 1000 680 470 2700 2200 1000 680 470 330 2700 2200 1000 680 470 330 2700 2000 680 470 73 74 77 74 75 76 79 82 83 81 74 81 83 83 83 83 75 76 80 84 82 73 74 77 74 75 76 79 82 83 81 74 81 83 83 83 83 75 76 80 84 www.aimtec.com F 051e R8.E Tel: +1 514 620 2722 1 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3G-NZ 3 Watt | DC-DC Converter Models Dual output Model Input Voltage (V) Output Voltage(V) Output Current max (mA) Isolation (VDC) Capacitor Load (μF) Efficiency (%) AM3G-0505D-NZ AM3G-0512D-NZ AM3G-0515D-NZ AM3G-1205D-NZ AM3G-1209D-NZ AM3G-1212D-NZ AM3G-1215D-NZ AM3G-2405D-NZ AM3G-2409D-NZ AM3G-2412D-NZ AM3G-2415D-NZ AM3G-4805D-NZ AM3G-4812D-NZ AM3G-4815D-NZ AM3G-0505DH30-NZ AM3G-0512DH30-NZ AM3G-0515DH30-NZ AM3G-1205DH30-NZ AM3G-1212DH30-NZ AM3G-1215DH30-NZ AM3G-2405DH30-NZ AM3G-2409DH30-NZ AM3G-2412DH30-NZ AM3G-2415DH30-NZ AM3G-4805DH30-NZ AM3G-4812DH30-NZ AM3G-4815DH30-NZ 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-75 36-75 36-75 ±5 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±12 ±15 ±250 ±104 ±83 ±300 ±167 ±125 ±100 ±300 ±167 ±125 ±100 ±300 ±125 ±100 ±250 ±104 ±83 ±300 ±125 ±100 ±300 ±167 ±125 ±100 ±300 ±125 ±100 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 ±1000 ±470 ±330 ±1000 ±680 ±470 ±330 ±1000 ±680 ±470 ±330 ±680 ±470 ±330 ±1000 ±470 ±330 ±1000 ±470 ±330 ±1000 ±680 ±470 ±330 ±1000 ±470 ±330 74 77 77 78 79 80 80 78 81 83 83 80 82 82 74 77 77 78 79 80 79 81 83 83 79 82 82 Input Specifications Parameters Voltage range Nominal Typical 5 12 24 48 Filter Maximum Rating 5 Vin 12 Vin 24 Vin 48 Vin Peak Input Voltage time No load input current Input Reflected Ripple Current On/Off Control* 5 Vin 12 Vin 24 Vin 48 Vin 5 Vin 12 Vin 24 Vin 48 Vin Maximum Units 4.5-9 9-18 18-36 36-75 Capacitor 12 25 50 100 VDC VDC 1 40 20 7 7 30 30 110 45 ON – open or Isolated; OFF – high (current 5-10mA) sec mA mA *Note: Exceeding 20mA of control current will permanently damage the converter. www.aimtec.com F 051e R8.E Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3G-NZ 3 Watt | DC-DC Converter Isolation Specifications Parameters Conditions Tested I/O voltage Resistance Capacitance Typical 60sec, <1mA Rated Units 1500, 3000 VDC MOhm pF > 1000 50 100kHz, 1V Output Specifications Parameters Voltage accuracy No Load Voltage accuracy Voltage balance Short Circuit Protection Short Circuit Restart Line voltage regulation Load voltage regulation Temperature coefficient Transient Recovery Time Transient Response Deviation Ripple Noise Conditions Typical 5 to 100% load ±2 ±5 ±1 Continuous Auto-recovery ±0.5 ±0.6 ±0.02 2 ±5 50 80 Dual Output balanced load LL~HL load 5~100% 25% load step 25% load step At 20MHz Bandwidth At 20MHz Bandwidth Maximum Units % % % % %/oC msec % mV p-p mV p-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 250 KHz oC Operating temperature With derating above 85oC -40 to +100 oC Storage temperature -55 to +125 oC Case Temperature 105 oC Lead Temperature 1.5mm from case for 10 Seconds 300 Cooling Free air convection Humidity 95 % Case material Plastic (UL94V-0 rated) Weight 4.9 g Dimensions (L x Wx H) 0.87 x 0.37 x 0.47 inch, 22 x 9.5 x 12 mm MTBF >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Pin Out Specifications Dimensions Pin Single Dual 1 2 3 5 6 7 8 - V Input + V Input On/Off Control N.C. + V Output - V Output CS - V Input + V Input On/Off Control N.C. + V Output Common - V Output 22.00 (0.87) PRINTED FACE 12.00 (0.47) 12.00 (0.47) 0.50 (0.02) 4.10 (0.16) 2.54 (0.10) 2.50 (0.98) www.aimtec.com F 051e R8.E 9.50 (0.37) 0.50 (0.02) 1 2 3 2.10 (0.08) Tel: +1 514 620 2722 3 of 5 5 6 7 8 0.300 (0.012) 9.50 (0.37) 0.50 (0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3G-NZ 3 Watt | DC-DC Converter Derating Free Air Convection 85º C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 105 100 Ambient Temperature º C Load Recommended EMC Circuit Model C1, C2 C4 LDM MOV TVS C3 LDM2 Cd D1 5 Vin 4.7µF / 50V 1nF /3KV 12 µH - SMCJ13A 680µF / 16V - 47nF /100V RB160M-60/1A 12 Vin 4.7µF / 50V 1nF /3KV 12 µH - SMCJ28A 680µF / 25V - 47nF /100V RB160M-60/1A 24 Vin 4.7µF / 50V 1nF /3KV 12 µH S14K35 SMCJ48A 330µF / 50V 56µH 47nF /100V RB160M-60/1A 48 Vin 4.7µF / 100V 1nF /3KV 12 µH S14K60 SMCJ90A 330µF / 100V 56µH 47nF /100V RB160M-60/1A R1 See Formula See Formula See Formula See Formula Note: Fuse is user selectable R1 = ((Vcd – Vd1 – 1.0) / Icntl) ‐ 300 www.aimtec.com F 051e R8.E Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3G-NZ 3 Watt | DC-DC Converter Recommended Circuits Single Output +Vout LDM + Vin 6 2 C1 C2 CNTL Cout 3 D1 R1 C3 ‐ Vin DC 8 DC 1 Cs 7 ‐ Vout Dual Output + Vin 6 2 C1 +Vout LDM1 LDM C2 CNTL 3 D1 R1 C3 ‐ Vin DC DC Cout GND 7 Cout LDM1 1 8 ‐ Vout Model 5 Vin 12 Vin 24 Vin 48 Vin C1 100µF 100µF 10µF 10µF C2 47µF 47µF 1µF 1µF LDM 4.7 - 12 µH 4.7 - 12 µH 4.7 - 12 µH 4.7 - 12 µH C3 47µF / 100V 47µF / 100V 47µF / 100V 47µF / 100V D1 RB160M-60/1A RB160M-60/1A RB160M-60/1A RB160M-60/1A R1 See Formula See Formula See Formula See Formula LDM1 2.2 - 10 µH 2.2 - 10 µH 2.2 - 10µH 2.2 - 10 µH CS 10 - 22µF 10 - 22µF 10 - 22µF 10 - 22µF Cout 100µF 100µF 100µF 100µF R1 = ((Vcd – Vd1 – 1.0) / Icntl) – 300 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R8.E Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only