Renesas HD6413005TE Microcomputer Datasheet

To all our customers
Regarding the change of names mentioned in the document, such as Hitachi
Electric and Hitachi XX, to Renesas Technology Corp.
The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and other Hitachi brand
names are mentioned in the document, these names have in fact all been changed to Renesas
Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and
corporate statement, no changes whatsoever have been made to the contents of the document, and
these changes do not constitute any alteration to the contents of the document itself.
Renesas Technology Home Page: http://www.renesas.com
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
Cautions
Keep safety first in your circuit designs!
1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corporation product best suited to the customer's application; they do not convey any
license under any intellectual property rights, or any other rights, belonging to Renesas Technology
Corporation or a third party.
2. Renesas Technology Corporation assumes no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corporation without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corporation
or an authorized Renesas Technology Corporation product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corporation assumes no responsibility for any damage, liability, or other loss
rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corporation by various
means, including the Renesas Technology Corporation Semiconductor home page
(http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams,
charts, programs, and algorithms, please be sure to evaluate all information as a total system before
making a final decision on the applicability of the information and products. Renesas Technology
Corporation assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device
or system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor
when considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be
exported under a license from the Japanese government and cannot be imported into a country other
than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corporation for further details on these materials or the products
contained therein.
OMC952723089
Hitachi Microcomputer
H8/3004, H8/3005
Hardware Manual
Preface
The H8/3004 and H8/3005 are high-performance single-chip microcontrollers that integrate
system supporting functions together with an H8/300H CPU core.
The H8/300H CPU has a 32-bit internal architecture with sixteen 16-bit general registers, and a
concise, optimized instruction set designed for speed. It can address a 16-Mbyte linear address
space.
The on-chip system supporting functions include RAM, a 16-bit integrated timer unit (ITU), a
watchdog timer (WDT), a serial communication interface (SCI), an A/D converter, I/O ports, and
other facilities.
Two operating modes offer a choice of address space size.
This manual describes the H8/3004 and H8/3005 hardware. For details of the instruction set, refer
to the H8/300H Programming Manual.
Contents
Section 1
1.1
1.2
1.3
1.4
Overview......................................................................................................
Overview ........................................................................................................................
Block Diagram................................................................................................................
Pin Description ...............................................................................................................
1.3.1
Pin Arrangement.............................................................................................
1.3.2
Pin Functions ..................................................................................................
Pin Functions ..................................................................................................................
Section 2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
CPU ...............................................................................................................
Overview ........................................................................................................................
2.1.1
Features...........................................................................................................
2.1.2
Differences from H8/300 CPU .......................................................................
CPU Operating Modes....................................................................................................
Address Space.................................................................................................................
Register Configuration....................................................................................................
2.4.1
Overview.........................................................................................................
2.4.2
General Registers............................................................................................
2.4.3
Control Registers ............................................................................................
2.4.4
Initial CPU Register Values ............................................................................
Data Formats...................................................................................................................
2.5.1
General Register Data Formats.......................................................................
2.5.2
Memory Data Formats ....................................................................................
Instruction Set.................................................................................................................
2.6.1
Instruction Set Overview ................................................................................
2.6.2
Instructions and Addressing Modes................................................................
2.6.3
Tables of Instructions Classified by Function.................................................
2.6.4
Basic Instruction Formats ...............................................................................
2.6.5
Notes on Use of Bit Manipulation Instructions ..............................................
Addressing Modes and Effective Address Calculation ..................................................
2.7.1
Addressing Modes ..........................................................................................
2.7.2
Effective Address Calculation ........................................................................
Processing States ............................................................................................................
2.8.1
Overview.........................................................................................................
2.8.2
Program Execution State ................................................................................
2.8.3
Exception-Handling State...............................................................................
2.8.4
Exception-Handling Sequences ......................................................................
2.8.5
Reset State ......................................................................................................
2.8.6
Power-Down State ..........................................................................................
1
1
4
5
5
6
9
13
13
13
14
15
16
17
17
18
19
20
21
21
22
24
24
25
26
36
37
37
37
40
44
44
45
45
47
48
48
2.9
Basic Operational Timing...............................................................................................
2.9.1
Overview.........................................................................................................
2.9.2
On-Chip Memory Access Timing...................................................................
2.9.3
On-Chip Supporting Module Access Timing .................................................
2.9.4
Access to External Address Space..................................................................
Section 3
3.1
3.2
3.3
3.4
3.5
MCU Operating Modes ...........................................................................
Overview ........................................................................................................................
3.1.1
Operating Mode Selection ..............................................................................
3.1.2
Register Configuration....................................................................................
Mode Control Register (MDCR) ....................................................................................
System Control Register (SYSCR).................................................................................
Operating Mode Descriptions.........................................................................................
3.4.1
Mode 1 ............................................................................................................
3.4.2
Mode 3 ............................................................................................................
Memory Map in Each Operating Mode..........................................................................
Section 4
4.1
4.2
4.3
4.4
4.5
4.6
Exception Handling ..................................................................................
Overview ........................................................................................................................
4.1.1
Exception Handling Types and Priority..........................................................
4.1.2
Exception Handling Operation .......................................................................
4.1.3
Exception Vector Table...................................................................................
Reset
........................................................................................................................
4.2.1
Overview.........................................................................................................
4.2.2
Reset Sequence ...............................................................................................
4.2.3
Interrupts after Reset.......................................................................................
Interrupts ........................................................................................................................
Trap Instruction...............................................................................................................
Stack Status after Exception Handling ...........................................................................
Notes on Stack Usage .....................................................................................................
Section 5
5.1
5.2
49
49
49
51
52
53
53
53
54
55
56
58
58
58
58
61
61
61
61
62
63
63
63
65
65
66
66
67
Interrupt Controller................................................................................... 69
Overview ........................................................................................................................
5.1.1
Features...........................................................................................................
5.1.2
Block Diagram................................................................................................
5.1.3
Pin Configuration............................................................................................
5.1.4
Register Configuration....................................................................................
Register Descriptions......................................................................................................
5.2.1
System Control Register (SYSCR).................................................................
5.2.2
Interrupt Priority Registers A and B (IPRA, IPRB) .......................................
5.2.3
IRQ Status Register (ISR) ..............................................................................
69
69
70
71
71
72
72
73
79
5.3
5.4
5.5
5.2.4
IRQ Enable Register (IER) .............................................................................
5.2.5
IRQ Sense Control Register (ISCR) ...............................................................
Interrupt Sources.............................................................................................................
5.3.1
External Interrupts ..........................................................................................
5.3.2
Internal Interrupts ...........................................................................................
5.3.3
Interrupt Vector Table .....................................................................................
Interrupt Operation .........................................................................................................
5.4.1
Interrupt Handling Process .............................................................................
5.4.2
Interrupt Sequence ..........................................................................................
5.4.3
Interrupt Response Time.................................................................................
Usage Notes ....................................................................................................................
5.5.1
Contention between Interrupt and Interrupt-Disabling Instruction ................
5.5.2
Instructions that Inhibit Interrupts ..................................................................
5.5.3
Interrupts during EEPMOV Instruction Execution.........................................
Section 6
6.1
6.2
6.3
6.4
7.3
Bus Controller ............................................................................................ 95
Overview ........................................................................................................................ 95
6.1.1
Features........................................................................................................... 95
6.1.2
Block Diagram................................................................................................ 96
6.1.3
Input/Output Pins............................................................................................ 97
6.1.4
Register Configuration.................................................................................... 97
Register Descriptions...................................................................................................... 98
6.2.1
Wait Control Register (WCR)......................................................................... 98
6.2.2
Access State Control Register (ASTCR) ........................................................ 99
6.2.3
Wait State Controller Enable Register (WCER)............................................. 100
Operation ........................................................................................................................ 101
6.3.1
Area Division.................................................................................................. 101
6.3.2
Bus Control Signal Timing ............................................................................. 103
6.3.3
Wait Modes ..................................................................................................... 105
6.3.4
Interconnections with Memory (Example)..................................................... 111
Usage Notes .................................................................................................................... 112
6.4.1
Register Write Timing .................................................................................... 112
Section 7
7.1
7.2
80
81
82
82
83
83
86
86
91
92
93
93
94
94
I/O Ports ....................................................................................................... 113
Overview ........................................................................................................................ 113
Port 6
........................................................................................................................ 115
7.2.1
Overview......................................................................................................... 115
7.2.2
Register Descriptions...................................................................................... 115
7.2.3
Pin Functions .................................................................................................. 117
Port 7
........................................................................................................................ 118
7.3.1
Overview......................................................................................................... 118
7.4
7.5
7.6
7.7
7.3.2
Port 8
7.4.1
7.4.2
7.4.3
Port 9
7.5.1
7.5.2
7.5.3
Port A
7.6.1
7.6.2
7.6.3
Port B
7.7.1
7.7.2
7.7.3
Section 8
8.1
8.2
8.3
Register Description ....................................................................................... 119
........................................................................................................................ 120
Overview......................................................................................................... 120
Register Descriptions...................................................................................... 121
Pin Functions .................................................................................................. 123
........................................................................................................................ 124
Overview......................................................................................................... 124
Register Descriptions...................................................................................... 124
Pin Functions .................................................................................................. 126
........................................................................................................................ 127
Overview......................................................................................................... 127
Register Descriptions...................................................................................... 128
Pin Functions ................................................................................................. 130
........................................................................................................................ 137
Overview......................................................................................................... 137
Register Descriptions...................................................................................... 137
Pin Functions .................................................................................................. 139
16-Bit Integrated Timer Unit (ITU)..................................................... 145
Overview ........................................................................................................................ 145
8.1.1
Features........................................................................................................... 145
8.1.2
Block Diagrams .............................................................................................. 148
8.1.3
Input/Output Pins............................................................................................ 153
8.1.4
Register Configuration.................................................................................... 154
Register Descriptions...................................................................................................... 157
8.2.1
Timer Start Register (TSTR) .......................................................................... 157
8.2.2
Timer Synchro Register (TSNC) .................................................................... 158
8.2.3
Timer Mode Register (TMDR)....................................................................... 160
8.2.4
Timer Function Control Register (TFCR) ...................................................... 163
8.2.5
Timer Output Master Enable Register (TOER) .............................................. 165
8.2.6
Timer Output Control Register (TOCR)......................................................... 168
8.2.7
Timer Counters (TCNT) ................................................................................. 169
8.2.8
General Registers (GRA, GRB) ..................................................................... 170
8.2.9
Buffer Registers (BRA, BRB) ........................................................................ 171
8.2.10
Timer Control Registers (TCR) ...................................................................... 172
8.2.11
Timer I/O Control Register (TIOR)................................................................ 174
8.2.12
Timer Status Register (TSR)........................................................................... 176
8.2.13
Timer Interrupt Enable Register (TIER)......................................................... 179
CPU Interface ................................................................................................................. 181
8.3.1
16-Bit Accessible Registers ............................................................................ 181
8.3.2
8-Bit Accessible Registers .............................................................................. 183
8.4
8.5
8.6
Operation ........................................................................................................................ 185
8.4.1
Overview......................................................................................................... 185
8.4.2
Basic Functions............................................................................................... 186
8.4.3
Synchronization .............................................................................................. 196
8.4.4
PWM Mode .................................................................................................... 198
8.4.5
Reset-Synchronized PWM Mode ................................................................... 202
8.4.6
Complementary PWM Mode.......................................................................... 205
8.4.7
Phase Counting Mode..................................................................................... 215
8.4.8
Buffering......................................................................................................... 217
8.4.9
ITU Output Timing......................................................................................... 224
Interrupts ........................................................................................................................ 226
8.5.1
Setting of Status Flags .................................................................................... 226
8.5.2
Clearing of Status Flags.................................................................................. 228
8.5.3
Interrupt Sources............................................................................................. 229
Usage Notes .................................................................................................................... 230
Section 9
9.1
9.2
9.3
9.4
9.5
Watchdog Timer ........................................................................................ 245
Overview ........................................................................................................................ 245
9.1.1
Features........................................................................................................... 245
9.1.2
Block Diagram................................................................................................ 246
9.1.3
Pin Configuration............................................................................................ 246
9.1.4
Register Configuration.................................................................................... 247
Register Descriptions...................................................................................................... 248
9.2.1
Timer Counter (TCNT)................................................................................... 248
9.2.2
Timer Control/Status Register (TCSR)........................................................... 249
9.2.3
Reset Control/Status Register (RSTCSR) ...................................................... 251
9.2.4
Notes on Register Access ............................................................................... 253
Operation ........................................................................................................................ 255
9.3.1
Watchdog Timer Operation............................................................................. 255
9.3.2
Interval Timer Operation ................................................................................ 256
9.3.3
Timing of Setting of Overflow Flag (OVF) .................................................... 257
9.3.4
Timing of Setting of Watchdog Timer Reset Bit (WRST) ............................. 258
Interrupts ........................................................................................................................ 259
Usage Notes .................................................................................................................... 259
Section 10
10.1
Serial Communication Interface ........................................................... 261
Overview ........................................................................................................................ 261
10.1.1
Features........................................................................................................... 261
10.1.2
Block Diagram................................................................................................ 263
10.1.3
Input/Output Pins............................................................................................ 264
10.1.4
Register Configuration.................................................................................... 264
10.2
10.3
10.4
10.5
Register Descriptions...................................................................................................... 265
10.2.1
Receive Shift Register (RSR) ......................................................................... 265
10.2.2
Receive Data Register (RDR)......................................................................... 265
10.2.3
Transmit Shift Register (TSR) ........................................................................ 266
10.2.4
Transmit Data Register (TDR)........................................................................ 266
10.2.5
Serial Mode Register (SMR) .......................................................................... 267
10.2.6
Serial Control Register (SCR) ........................................................................ 271
10.2.7
Serial Status Register (SSR) ........................................................................... 275
10.2.8
Bit Rate Register (BRR) ................................................................................. 279
Operation ........................................................................................................................ 288
10.3.1
Overview......................................................................................................... 288
10.3.2
Operation in Asynchronous Mode.................................................................. 290
10.3.3
Multiprocessor Communication ..................................................................... 299
10.3.4
Synchronous Operation .................................................................................. 306
SCI Interrupts.................................................................................................................. 315
Usage Notes .................................................................................................................... 316
Section 11
11.1
11.2
11.3
11.4
11.5
11.6
A/D Converter ............................................................................................ 321
Overview ........................................................................................................................ 321
11.1.1
Features........................................................................................................... 321
11.1.2
Block Diagram................................................................................................ 322
11.1.3
Input Pins ........................................................................................................ 323
11.1.4
Register Configuration.................................................................................... 324
Register Descriptions...................................................................................................... 325
11.2.1
A/D Data Registers A to D (ADDRA to ADDRD) ........................................ 325
11.2.2
A/D Control/Status Register (ADCSR) .......................................................... 326
11.2.3
A/D Control Register (ADCR) ....................................................................... 329
CPU Interface ................................................................................................................. 330
Operation ........................................................................................................................ 331
11.4.1
Single Mode (SCAN = 0) ............................................................................... 331
11.4.2
Scan Mode (SCAN = 1).................................................................................. 333
11.4.3
Input Sampling and A/D Conversion Time .................................................... 335
11.4.4
External Trigger Input Timing........................................................................ 336
Interrupts ........................................................................................................................ 337
Usage Notes .................................................................................................................... 337
Section 12
12.1
12.2
RAM ............................................................................................................. 339
Overview ........................................................................................................................ 339
12.1.1
Block Diagram................................................................................................ 339
12.1.2
Register Configuration.................................................................................... 340
System Control Register (SYSCR)................................................................................. 341
12.3
Operation ........................................................................................................................ 342
Section 13
13.1
13.2
13.3
13.4
Clock Pulse Generator ............................................................................. 343
Overview ........................................................................................................................ 343
13.1.1
Block Diagram................................................................................................ 343
Oscillator Circuit ............................................................................................................ 344
13.2.1
Connecting a Crystal Resonator ..................................................................... 344
13.2.2
External Clock Input....................................................................................... 346
Duty Adjustment Circuit................................................................................................. 348
Prescalers ........................................................................................................................ 348
Section 14
14.1
14.2
14.3
14.4
14.5
Overview ........................................................................................................................ 349
Register Configuration.................................................................................................... 350
14.2.1
System Control Register (SYSCR)................................................................. 350
Sleep Mode ..................................................................................................................... 352
14.3.1
Transition to Sleep Mode................................................................................ 352
14.3.2
Exit from Sleep Mode..................................................................................... 352
Software Standby Mode ................................................................................................. 353
14.4.1
Transition to Software Standby Mode ............................................................ 353
14.4.2
Exit from Software Standby Mode ................................................................. 353
14.4.3
Selection of Waiting Time for Exit from Software Standby Mode ................ 354
14.4.4
Sample Application of Software Standby Mode ............................................ 355
14.4.5
Note................................................................................................................. 355
Hardware Standby Mode ................................................................................................ 356
14.5.1
Transition to Hardware Standby Mode........................................................... 356
14.5.2
Exit from Hardware Standby Mode................................................................ 356
14.5.3
Timing for Hardware Standby Mode.............................................................. 356
Section 15
15.1
15.2
15.3
Power-Down State .................................................................................... 349
Electrical Characteristics ........................................................................ 357
Absolute Maximum Ratings ........................................................................................... 357
Electrical Characteristics ................................................................................................ 358
15.2.1
DC Characteristics .......................................................................................... 358
15.2.2
AC Characteristics .......................................................................................... 368
15.2.3
A/D Conversion Characteristics ..................................................................... 375
Operational Timing......................................................................................................... 376
15.3.1
Bus Timing ..................................................................................................... 376
15.3.2
Control Signal Timing .................................................................................... 380
15.3.3
Clock Timing .................................................................................................. 382
15.3.4
I/O Port Timing............................................................................................... 382
15.3.5
ITU Timing ..................................................................................................... 383
15.3.6
SCI Input/Output Timing................................................................................ 384
Appendix A Instruction Set ............................................................................................ 385
A.1
A.2
A.3
Instruction List................................................................................................................ 385
Operation Code Maps ..................................................................................................... 400
Number of States Required for Execution...................................................................... 403
Appendix B Register Field ............................................................................................. 412
B.1
B.2
Register Addresses and Bit Names................................................................................. 412
Register Descriptions...................................................................................................... 420
Appendix C I/O Port Block Diagrams ........................................................................ 461
C.1
C.2
C.3
C.4
C.5
C.6
Port 6 Block Diagram ..................................................................................................... 461
Port 7 Block Diagram ..................................................................................................... 462
Port 8 Block Diagram ..................................................................................................... 463
Port 9 Block Diagram ..................................................................................................... 465
Port A Block Diagram .................................................................................................... 468
Port B Block Diagram .................................................................................................... 471
Appendix D Pin States ..................................................................................................... 475
D.1
D.2
Port States in Each Mode................................................................................................ 475
Pin States at Reset........................................................................................................... 476
Appendix E
Timing of Transition to and Recovery
from Hardware Standby Mode.............................................................. 479
Appendix F
Product Code Lineup ............................................................................... 480
Appendix G Package Dimensions ................................................................................ 481
Section 1 Overview
1.1 Overview
The H8/3004 and H8/3005 are microcontrollers (MCUs) that integrate system supporting
functions together with an H8/300H CPU core having an original Hitachi architecture.
The H8/300H CPU has a 32-bit internal architecture with sixteen 16-bit general registers, and a
concise, optimized instruction set designed for speed. It can address a 16-Mbyte linear address
space. Its instruction set is upward-compatible at the object-code level with the H8/300 CPU,
enabling easy porting of software from the H8/300 Series.
The on-chip system supporting functions include RAM, a 16-bit integrated timer unit (ITU), a
watchdog timer (WDT), a serial communication interface (SCI), an A/D converter, I/O ports, and
other facilities.
Two MCU operating modes—modes 1 and 3—offer a choice of address space size.
Table 1-1 summarizes the features of the H8/3004 and H8/3005.
1
Table 1-1 Features
Feature
Description
CPU
Upward-compatible with the H8/300 CPU at the object-code level
General-register machine
• Sixteen 16-bit general registers
(also useable as sixteen 8-bit registers or eight 32-bit registers)
High-speed operation
• Maximum clock rate: 16 MHz
• Add/subtract: 125 ns
• Multiply/divide: 875 ns
Two CPU operating modes
• Normal mode (64-kbyte address space; cannot be used with the H8/3004 or
H8/3005)
• Advanced mode (16-Mbyte address space)
Instruction features
•
•
•
•
•
8/16/32-bit data transfer, arithmetic, and logic instructions
Signed and unsigned multiply instructions (8 bits ×8 bits, 16 bits ×16 bits)
Signed and unsigned divide instructions (16 bits ÷ 8 bits, 32 bits ÷ 16 bits)
Bit accumulator function
Bit manipulation instructions with register-indirect specification of bit positions
Memory
• H8/3004 RAM: 2 kbyte, H8/3005 RAM: 4 kbyte
Interrupt
controller
• Six external interrupt pins: NMI, IRQ0 to IRQ4
• 21 internal interrupts
• Three selectable interrupt priority levels
Bus controller
• Address space can be partitioned into eight areas, with independent bus
specifications in each area
• Two-state or three-state access selectable for each area
• Selection of four wait modes
• Bus arbitration function
16-bit integrated
timer unit (ITU)
• Five 16-bit timer channels, capable of processing up to 12 pulse outputs or 10
pulse inputs
• 16-bit timer counter (channels 0 to 4)
• Two multiplexed output compare/input capture pins (channels 0 to 4)
• Operation can be synchronized (channels 0 to 4)
• PWM mode available (channels 0 to 4)
• Phase counting mode available (channel 2)
• Buffering available (channels 3 and 4)
• Reset-synchronized PWM mode available (channels 3 and 4)
• Complementary PWM mode available (channels 3 and 4)
2
Table 1-1 Features (cont)
Feature
Description
Watchdog
timer (WDT),
1 channel
• Reset signal can be generated by overflow
• Reset signal can be output externally
• Usable as an interval timer
Serial
communication
interface (SCI),
1 channel
• Selection of asynchronous or synchronous mode
• Full duplex: can transmit and receive simultaneously
• On-chip baud-rate generator
A/D converter
•
•
•
•
•
I/O ports
• 21 input/output pins
• 11 input-only pins
Resolution: 10 bits
Eight channels, with selection of single or scan mode
Variable analog conversion voltage range
Sample-and-hold function
Can be externally triggered
Operating modes Two MCU operating modes
Mode
Address
Space
Address
Pins
Mode 1
1 Mbyte
A0 to A19
Mode 3
16 Mbyte
A0 to A23
Power-down
state
• Sleep mode
• Software standby mode
• Hardware standby mode
Other features
• On-chip clock oscillator
Product lineup
Power Supply
Voltage
Model
Package
HD6413004F
HD6413004VF
80-pin QFP (FP-80A)
5 V ±10%
2.7 to 5.5 V
HD6413004TE
HD6413004VTE
80-pin TQFP (TFP-80C)
5 V ±10%
2.7 V to 5.5 V
HD6413005F
HD6413005VF
80-pin QFP (FP-80A)
5 V ±10%
2.7 V to 5.5 V
HD6413005TE
HD6413005VTE
80-pin TQFP (TFP-80C)
5 V ±10%
2.7 V to 5.5 V
3
1.2 Block Diagram
Address bus
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Port 8
P83/IRQ3
P82/IRQ2
P81/IRQ1
P80/IRQ0
Port 9
D7
D6
D5
D4
D3
D2
D1
D0
VSS
VSS
VSS
VCC
VCC
Figure 1-1 shows an internal block diagram.
P94/SCK/IRQ4
P92/RxD
P90/TxD
Data bus
Address bus
Data bus (upper)
MD1
MD0
EXTAL
XTAL
ø
STBY
RES
RESO
NMI
Data bus (lower)
Clock
osc.
H8/300H CPU
Interrupt controller
AS
RD
WR
RAM*
Bus controller
Serial communication
interface (SCI) × 1 channel
Watchdog timer
16 bit
integrated timer unit
(ITU)
PA7/TIOCB2/A20
PA6/TIOCA2/A21
PA5/TIOCB1/A22
PA4/TIOCA1/A23
PA3/TIOCB0/TCLKD
PA2/TIOCA0/TCLKC
PA1/TCLKB
PA0/TCLKA
Port A
PB7/ADTRG
PB6
PB5/TOCXB4
PB4/TOCXA4
PB3/TIOCB4
PB2/TIOCA4
PB1/TIOCB3
PB0/TIOCA3
Port B
A/D converter
Port 7
AVCC
AVSS
VREF
P77/AN7
P76/AN6
P75/AN5
P74/AN4
P73/AN3
P72/AN2
P71/AN1
P70/AN0
P60/WAIT
Port 6
Wait-state controller
Note: * 2 kbytes in the H8/3004, 4 kbytes in the H8/3005.
Figure 1-1 Block Diagram
4
1.3 Pin Description
1.3.1 Pin Arrangement
PA1/TCLKB
PA0/TCLKA
P83/IRQ3
P82/IRQ2
P81/IRQ1
P80/IRQ0
AVCC
VREF
P77/AN7
P76/AN6
P75/AN5
P74/AN4
P73/AN3
P72/AN2
74
73
72
71
70
69
68
67
66
65
64
63
62
61
PA3/TIOCB0/TCLKD
PA4/TIOCA1/A23
77
PA2/TIOCA0/TCLKC
PA5/TIOCB1/A22
78
75
PA6/TIOCA2/A21
79
76
PA7/TIOCB2/A20
80
Figure 1-2 shows the pin arrangement of the H8/3004 and H8/3005, FP-80A and TFP-80C
package.
PB0/TIOCA3
1
60
P71/AN1
PB1/TIOCB3
2
59
P70/AN0
PB2/TIOCA4
3
58
AVSS
PB3/TIOCB4
4
57
RESO
PB4/TOCXA4
5
56
WR
PB5/TOCXB4
6
55
RD
PB6
7
54
AS
PB7/ADTRG
8
53
VCC
P90/TxD
9
52
XTAL
37
38
39
40
A14
A15
A16
A17
A18
36
41
A13
20
35
D7
A12
A19
34
P60/WAIT
42
A11
43
19
A10
18
D6
33
D5
32
MD0
A9
44
31
17
A8
MD1
D4
30
45
29
16
A7
ø
D3
VSS
46
28
15
27
STBY
D2
A6
47
A5
14
26
RES
D1
A4
48
A3
13
25
NMI
D0
24
49
A2
12
23
VSS
VSS
A1
EXTAL
50
22
51
(FP-80A, TFP-80C)
21
Top view
11
A0
10
VCC
P92/RxD
P94/SCK/IRQ4
Figure 1-2 Pin Arrangement (FP-80A, TFP-80C, Top View)
5
1.3.2 Pin Functions
Pin Assignments in Each Mode: Table 1-2 lists the FP-80A and TFP-80C pin assignments in
each mode.
Table 1-2 FP-80A and TFP-80C Pin Assignments in Each Mode
Pin Name
Pin No.
Mode 1
Mode 3
1
PB0/TIOCA3
PB0/TIOCA3
2
PB1/TIOCB3
PB1/TIOCB3
3
PB2/TIOCA4
PB2/TIOCA4
4
PB3/TIOCB4
PB3/TIOCB4
5
PB4/TOCXA4
PB4/TOCXA4
6
PB5/TOCXB4
PB5/TOCXB4
7
PB6
PB6
8
PB7/ADTRG
PB7/ADTRG
9
P90/TxD
P90/TxD
10
P92/RxD
P92/RxD
11
P94/SCK/IRQ4
P94/SCK/IRQ4
12
VSS
VSS
13
D0
D0
14
D1
D1
15
D2
D2
16
D3
D3
17
D4
D4
18
D5
D5
19
D6
D6
20
D7
D7
21
VCC
VCC
22
A0
A0
23
A1
A1
24
A2
A2
25
A3
A3
6
Table 1-2 FP-80A and TFP-80C Pin Assignments in Each Mode (cont)
Pin Name
Pin No.
Mode 1
Mode 3
26
A4
A4
27
A5
A5
28
A6
A6
29
A7
A7
30
VSS
VSS
31
A8
A8
32
A9
A9
33
A10
A10
34
A11
A11
35
A12
A12
36
A13
A13
37
A14
A14
38
A15
A15
39
A16
A16
40
A17
A17
41
A18
A18
42
A19
A19
43
P60/WAIT
P60/WAIT
44
MD0
MD0
45
MD1
MD1
46
ø
ø
47
STBY
STBY
48
RES
RES
49
NMI
NMI
50
VSS
VSS
51
EXTAL
EXTAL
52
XTAL
XTAL
53
VCC
VCC
7
Table 1-2 FP-80A and TFP-80C Pin Assignments in Each Mode (cont)
Pin Name
Pin No.
Mode 1
Mode 3
54
AS
AS
55
RD
RD
56
WR
WR
57
RESO
RESO
58
AVSS
AVSS
59
P70/AN0
P70/AN0
60
P71/AN1
P71/AN1
61
P72/AN2
P72/AN2
62
P73/AN3
P73/AN3
63
P74/AN4
P74/AN4
64
P75/AN5
P75/AN5
65
P76/AN6
P76/AN6
66
P77/AN7
P77/AN7
67
VREF
VREF
68
AVCC
AVCC
69
P80/IRQ0
P80/IRQ0
70
P81/IRQ1
P81/IRQ1
71
P82/IRQ2
P82/IRQ2
72
P83/IRQ3
P83/IRQ3
73
PA0/TCLKA
PA0/TCLKA
74
PA1/TCLKB
PA1/TCLKB
75
PA2/TIOCA0/TCLKC
PA2/TIOCA0/TCLKC
76
PA3/TIOCB0/TCLKD
PA3/TIOCB0/TCLKD
77
PA4/TIOCA1
A23
78
PA5/TIOCB1
A22
79
PA6/TIOCA2
A21
80
PA7/TIOCB2
A20
8
1.4 Pin Functions
Table 1-3 summarizes the pin functions.
Table 1-3 Pin Functions
Type
Symbol
Pin No.
I/O
Name and Function
Power
VCC
21, 53
Input
Power: For connection to the power supply
(+5 V). Connect all VCC pins to the +5-V system
power supply.
VSS
12, 30, 50
Input
Ground: For connection to ground (0 V).
Connect all VSS pins to the 0-V system power
supply.
XTAL
52
Input
For connection to a crystal resonator.
For examples of crystal resonator and external
clock input, see section 13, Clock Pulse
Generator.
EXTAL
51
Input
For connection to a crystal resonator or input of
an external clock signal. For examples of
crystal resonator and external clock input, see
section 13, Clock Pulse Generator.
ø
46
Output System clock: Supplies the system clock to
external devices
MD1,
MD0
44,
45
Input
Clock
Operating
mode control
System control RES
Mode 1 and mode 0: For setting the operating
mode, as follows
MD1
MD0
Operating Mode
0
0
—
0
1
Mode 1
1
0
—
1
1
Mode 3
48
Input
Reset input: When driven low, this pin resets
the H8/3004 or H8/3005
RESO
57
Output Reset output: Outputs a reset signal to
external devices
STBY
47
Input
Standby: When driven low, this pin forces
a transition to hardware standby mode
9
Table 1-3 Pin Functions (cont)
Type
Symbol
Pin No.
I/O
Name and Function
Interrupts
NMI
49
Input
Nonmaskable interrupt: Requests a
nonmaskable interrupt
IRQ4 to
IRQ0
11,
72 to 69
Input
Interrupt request 4 to 0: Maskable interrupt
request pins
Mode 1 A19 to A0
22 to 29
31 to 42
Output Address bus: Outputs address signals
Mode 3 A23 to A0
80 to 77
22 to 29
31 to 42
Address
bus
Data bus
D7 to D0
20 to 13
Input/
output
Bus control
AS
54
Output Address strobe: Goes low to indicate valid
address output on the address bus
RD
55
Output Read: Goes low to indicate reading from the
external address space
WR
56
Output High write: Goes low to indicate writing to the
external address space; indicates valid data on
the upper half of the data bus (D7 to D0).
WAIT
43
Input
Wait: Requests insertion of wait states in bus
cycles during access to the external address
space
TCLKD to
TCLKA
76 to 73
Input
Clock input A to D: External clock inputs
TIOCA4 to
TIOCA0
3, 1, 79,
77, 75
Input/
output
Input capture/output compare A4 to A0:
GRA4 to GRA0 output compare or input
capture, or PWM output
TIOCB4 to
TIOCB0
4, 2, 80,
78, 76
Input/
output
Input capture/output compare B4 to B0:
GRB4 to GRB0 output compare or input
capture, or PWM output
TOCXA4
5
Output Output compare XA4: PWM output
TOCXB4
6
Output Output compare XB4: PWM output
16-bit
integrated
time unit
(ITU)
10
Data bus: Bidirectional data bus
Table 1-3 Pin Functions (cont)
Type
Symbol
Pin No.
I/O
Serial communication
interface (SCI)
TxD
9
Output Transmit data: SCI data output
RxD
10
Input
Receive data: SCI data input
SCK
11
Input/
output
Serial clock: SCI clock input/output
AN7 to AN0 66 to 59
Input
Analog 7 to 0: Analog input pins
ADTRG
8
Input
A/D trigger: External trigger input for starting
A/D conversion
AVCC
68
Input
Power supply pin for the A/D converter.
Connect to the system power supply (+5 V)
when not using the A/D converter.
AVSS
58
Input
Ground pin for the A/D converter. Connect to
system ground (0 V) when not using the A/D
converter.
VREF
67
Input
Reference voltage input pin for the A/D
converter. Connect to the system power supply
(+5 V) when not using the A/D converter.
P60
43
Input/
output
Port 6: One input/output pins. The direction
of each pin can be selected in the port 6 data
direction register (P6DDR).
P77 to P70
66 to 59
Input
Port 7: Eight input pins
P83 to P81
72 to 70
Input
Port 8: Three input pins. Do not designate
these pins as output pins in the port 8 data
direction register (P8DDR).
P80
69
Input/
output
Port 8: One input/output pin. The direction of
the pin can be selected in the port 80 data
direction register (P80DDR).
P94, P92,
P90
11 to 9
Input/
output
Port 9: Three input/output pins. The direction
of each pin can be selected in the port 9 data
direction register (P9DDR).
PA7 to PA0
80 to 73
Input/
output
Port A: Eight input/output pins. The direction of
each pin can be selected in the port A data
direction register (PADDR).
Input/
output
Port B: Eight input/output pins. The direction of
each pin can be selected in the port B data
direction register (PBDDR).
A/D
converter
I/O ports
PB7 to PB0 8 to 1
Name and Function
11
12
Section 2 CPU
2.1 Overview
The H8/300H CPU is a high-speed central processing unit with an internal 32-bit architecture that
is upward-compatible with the H8/300 CPU. The H8/300H CPU has sixteen 16-bit general
registers, can address a 16-Mbyte linear address space, and is ideal for realtime control.
2.1.1 Features
The H8/300H CPU has the following features.
•
Upward compatibility with H8/300 CPU
Can execute H8/300 series object programs without alteration
•
General-register architecture
Sixteen 16-bit general registers (also usable as sixteen 8-bit registers or eight 32-bit registers)
•
Sixty-two basic instructions
— 8/16/32-bit arithmetic and logic instructions
— Multiply and divide instructions
— Powerful bit-manipulation instructions
•
Eight addressing modes
—
—
—
—
—
—
—
—
•
Register direct [Rn]
Register indirect [@ERn]
Register indirect with displacement [@(d:16, ERn) or @(d:24, ERn)]
Register indirect with post-increment or pre-decrement [@ERn+ or @–ERn]
Absolute address [@aa:8, @aa:16, or @aa:24]
Immediate [#xx:8, #xx:16, or #xx:32]
Program-counter relative [@(d:8, PC) or @(d:16, PC)]
Memory indirect [@@aa:8]
16-Mbyte linear address space
13
•
High-speed operation
—
—
—
—
—
—
—
•
All frequently-used instructions execute in two to four states
Maximum clock frequency:
16 MHz
8/16/32-bit register-register add/subtract: 125 ns
8 ×8-bit register-register multiply:
875 ns
16 ÷ 8-bit register-register divide:
875 ns
16 ×16-bit register-register multiply:
1.375 µs
32 ÷ 16-bit register-register divide:
1.375 µs
Two CPU operating modes
— Normal mode (Cannot be used with the H8/3004 or H8/3005.)
— Advanced mode
•
Low-power mode
Transition to power-down state by SLEEP instruction
2.1.2 Differences from H8/300 CPU
In comparison to the H8/300 CPU, the H8/300H has the following enhancements.
•
More general registers
Eight 16-bit registers have been added.
•
Expanded address space
— Advanced mode supports a maximum 16-Mbyte address space.
— Normal mode supports the same 64-kbyte address space as the H8/300 CPU.
(Cannot be used with the H8/3004 or H8/3005.)
•
Enhanced addressing
The addressing modes have been enhanced to make effective use of the 16-Mbyte address
space.
•
Enhanced instructions
— Data transfer, arithmetic, and logic instructions can operate on 32-bit data.
— Signed multiply/divide instructions and other instructions have been added.
14
2.2 CPU Operating Modes
The H8/300H CPU has two operating modes: normal and advanced. Normal mode supports a
maximum 64-kbyte address space. Advanced mode supports up to 16 Mbytes. See figure 2-1. The
H8/3004 and H8/3005 can only be used in advanced mode.
Normal mode*
Maximum 64 kbytes, program
and data areas combined
Advanced mode
Maximum 16 Mbyte, program
and data areas combined
CPU operating modes
Note: * Normal mode cannot be used with the H8/3004 or H8/3005.
Figure 2-1 CPU Operating Modes
15
2.3 Address Space
The H8/300H CPU can address a linear address space with a maximum size of 16 Mbytes.
1-Mbyte mode or 16-Mbyte mode can be selected for the H8/300H address space, according to the
MCU operating mode. An outline memory map for the H8/3004 and H8/3005 is shown in figure
2-2. For further details see section 3.5, Memory Map in Each Operating Mode.
The 1-Mbyte operating mode uses 20-bit addressing. The upper 4 bits of effective addresses are
ignored.
H'00000
H'000000
H'FFFFF
H'FFFFFF
a. 1-Mbyte mode
b. 16-Mbyte mode
Figure 2-2 Memory Map
16
2.4 Register Configuration
2.4.1 Overview
The H8/300H CPU has the internal registers shown in figure 2-3. There are two types of registers:
general registers and control registers.
General Registers (ERn)
15
0 7
0 7
0
ER0
E0
R0H
R0L
ER1
E1
R1H
R1L
ER2
E2
R2H
R2L
ER3
E3
R3H
R3L
ER4
E4
R4H
R4L
ER5
E5
R5H
R5L
ER6
E6
R6H
R6L
R7H
R7L
(SP)
E7
ER7
Control Registers (CR)
23
0
PC
7 6 5 4 3 2 1 0
CCR I UI H U N Z V C
Legend
SP: Stack pointer
PC: Program counter
CCR: Condition code register
Interrupt mask bit
I:
User bit or interrupt mask bit
UI:
Half-carry flag
H:
User bit
U:
Negative flag
N:
Zero flag
Z:
Overflow flag
V:
Carry flag
C:
Figure 2-3 CPU Registers
17
2.4.2 General Registers
The H8/300H CPU has eight 32-bit general registers. These general registers are all functionally
alike and can be used without distinction between data registers and address registers. When a
general register is used as a data register, it can be accessed as a 32-bit, 16-bit, or 8-bit register.
When the general registers are used as 32-bit registers or as address registers, they are designated
by the letters ER (ER0 to ER7).
The ER registers divide into 16-bit general registers designated by the letters E (E0 to E7) and R
(R0 to R7). These registers are functionally equivalent, providing a maximum sixteen 16-bit
registers. The E registers (E0 to E7) are also referred to as extended registers.
The R registers divide into 8-bit general registers designated by the letters RH (R0H to R7H) and
RL (R0L to R7L). These registers are functionally equivalent, providing a maximum sixteen 8-bit
registers.
Figure 2-4 illustrates the usage of the general registers. The usage of each register can be selected
independently.
• Address registers
• 32-bit registers
• 16-bit registers
• 8-bit registers
E registers
(extended registers)
E0 to E7
RH registers
R0H to R7H
ER registers
ER0 to ER7
R registers
R0 to R7
RL registers
R0L to R7L
Figure 2-4 Usage of General Registers
18
General register ER7 has the function of stack pointer (SP) in addition to its general-register
function, and is used implicitly in exception handling and subroutine calls. Figure 2-5 shows the
stack.
Free area
SP (ER7)
Stack area
Figure 2-5 Stack
2.4.3 Control Registers
The control registers are the 24-bit program counter (PC) and the 8-bit condition code register
(CCR).
Program Counter (PC): This 24-bit counter indicates the address of the next instruction the CPU
will execute. The length of all CPU instructions is 2 bytes (one word) or a multiple of 2 bytes, so
the least significant PC bit is ignored. When an instruction is fetched, the least significant PC bit is
regarded as 0.
Condition Code Register (CCR): This 8-bit register contains internal CPU status information,
including the interrupt mask bit (I) and half-carry (H), negative (N), zero (Z), overflow (V), and
carry (C) flags.
Bit 7—Interrupt Mask Bit (I): Masks interrupts other than NMI when set to 1. NMI is accepted
regardless of the I bit setting. The I bit is set to 1 at the start of an exception-handling sequence.
Bit 6—User Bit or Interrupt Mask Bit (UI): Can be written and read by software using the
LDC, STC, ANDC, ORC, and XORC instructions. This bit can also be used as an interrupt mask
bit. For details see section 5, Interrupt Controller.
19
Bit 5—Half-Carry Flag (H): When the ADD.B, ADDX.B, SUB.B, SUBX.B, CMP.B, or NEG.B
instruction is executed, this flag is set to 1 if there is a carry or borrow at bit 3, and cleared to 0
otherwise. When the ADD.W, SUB.W, CMP.W, or NEG.W instruction is executed, the H flag is
set to 1 if there is a carry or borrow at bit 11, and cleared to 0 otherwise. When the ADD.L,
SUB.L, CMP.L, or NEG.L instruction is executed, the H flag is set to 1 if there is a carry or
borrow at bit 27, and cleared to 0 otherwise.
Bit 4—User Bit (U): Can be written and read by software using the LDC, STC, ANDC, ORC,
and XORC instructions.
Bit 3—Negative Flag (N): Indicates the most significant bit (sign bit) of data.
Bit 2—Zero Flag (Z): Set to 1 to indicate zero data, and cleared to 0 to indicate non-zero data.
Bit 1—Overflow Flag (V): Set to 1 when an arithmetic overflow occurs, and cleared to 0 at other
times.
Bit 0—Carry Flag (C): Set to 1 when a carry occurs, and cleared to 0 otherwise. Used by:
•
•
•
Add instructions, to indicate a carry
Subtract instructions, to indicate a borrow
Shift and rotate instructions, to store the value shifted out of the end bit
The carry flag is also used as a bit accumulator by bit manipulation instructions.
Some instructions leave flag bits unchanged. Operations can be performed on CCR by the LDC,
STC, ANDC, ORC, and XORC instructions. The N, Z, V, and C flags are used by conditional
branch (Bcc) instructions.
For the action of each instruction on the flag bits, see appendix A.1, Instruction List. For the I and
UI bits, see section 5, Interrupt Controller.
2.4.4 Initial CPU Register Values
In reset exception handling, PC is initialized to a value loaded from the vector table, and the I bit
in CCR is set to 1. The other CCR bits and the general registers are not initialized. In particular,
the stack pointer (ER7) is not initialized. The stack pointer must therefore be initialized by an
MOV.L instruction executed immediately after a reset.
20
2.5 Data Formats
The H8/300H CPU can process 1-bit, 4-bit (BCD), 8-bit (byte), 16-bit (word), and 32-bit
(longword) data. Bit-manipulation instructions operate on 1-bit data by accessing bit n (n = 0, 1,
2, …, 7) of byte operand data. The DAA and DAS decimal-adjust instructions treat byte data as
two digits of 4-bit BCD data.
2.5.1 General Register Data Formats
Figures 2-6 and 2-7 show the data formats in general registers.
Data Type
General
Register
1-bit data
RnH
7 6 5 4 3 2 1 0
1-bit data
RnL
Don’t care
4-bit BCD data
RnH
Upper digit Lower digit
4-bit BCD data
RnL
Don’t care
Byte data
RnH
Data Format
7
0
Don’t care
7
7
4 3
0
Don’t care
7
7
4 3
0
Upper digit Lower digit
0
Don’t care
MSB
Byte data
0
7 6 5 4 3 2 1 0
LSB
7
0
MSB
LSB
Don’t care
RnL
Figure 2-6 General Register Data Formats (1)
21
Data Type
General
Register
Word data
Rn
Word data
Data Format
15
0
MSB
LSB
15
0
MSB
LSB
En
31
16 15
0
Longword data ERn
MSB
LSB
Legend
ERn: General register
En:
General register E
Rn:
General register R
RnH: General register RH
RnL: General register RL
MSB: Most significant bit
LSB: Least significant bit
Figure 2-7 General Register Data Formats (2)
2.5.2 Memory Data Formats
Figure 2-8 shows the data formats on memory. The H8/300H CPU can access word data and
longword data on memory, but word or longword data must begin at an even address. If an attempt
is made to access word or longword data at an odd address, no address error occurs but the least
significant bit of the address is regarded as 0, so the access starts at the preceding address. This
also applies to instruction fetches.
22
Data Type
Address
Data Format
1-bit data
Address
7
Byte data
Address
MSB
Word data
Address 2m
MSB
7
0
6
5
4
Address 2m + 1
2
1
0
LSB
LSB
Address 2n
Longword data
3
MSB
Address 2n + 1
Address 2n + 2
Address 2n + 3
LSB
Figure 2-8 Memory Data Formats
When ER7 (SP) is used as an address register to access the stack, the operand size should be word
size or longword size.
23
2.6 Instruction Set
2.6.1 Instruction Set Overview
The H8/300H CPU has 62 types of instructions, which are classified in table 2-1.
Table 2-1 Instruction Classification
Function
Instruction
PUSH*1,
Types
POP*1,
MOVTPE*2,
MOVFPE*2
3
Data transfer
MOV,
Arithmetic operations
ADD, SUB, ADDX, SUBX, INC, DEC, ADDS, SUBS, DAA, DAS,
MULXU, DIVXU, MULXS, DIVXS, CMP, NEG, EXTS, EXTU
18
Logic operations
AND, OR, XOR, NOT
4
Shift operations
SHAL, SHAR, SHLL, SHLR, ROTL, ROTR, ROTXL, ROTXR
8
Bit manipulation
BSET, BCLR, BNOT, BTST, BAND, BIAND, BOR, BIOR, BXOR,
BIXOR, BLD, BILD, BST, BIST
14
Branch
Bcc*3, JMP, BSR, JSR, RTS
5
System control
TRAPA, RTE, SLEEP, LDC, STC, ANDC, ORC, XORC, NOP
9
Block data transfer
EEPMOV
1
Total 62 types
Notes: 1. POP.W Rn is identical to MOV.W @SP+, Rn.
PUSH.W Rn is identical to MOV.W Rn, @–SP.
POP.L ERn is identical to MOV.L @SP+, Rn.
PUSH.L ERn is identical to MOV.L Rn, @–SP.
2. They are not available on H8/3004 and H8/3005.
3. Bcc is a generic branching instruction.
24
2.6.2 Instructions and Addressing Modes
Table 2-2 indicates the instructions available in the H8/300H CPU.
Table 2-2 Instructions and Addressing Modes
Addressing Modes
Rn
@
@
(d:16, (d:24, @ERn+/ @
@ERn ERn) ERn) @–ERn aa:8
Function
Instruction
#xx
Data
transfer
MOV
BWL BWL BWL
BWL
BWL
BWL
B
@
aa:16
@
@
(d:8,
aa:24 PC)
@
(d:16, @@
PC)
aa:8
Implied
BWL
BWL
—
—
—
—
POP, PUSH
—
—
—
—
—
—
—
—
—
—
—
—
WL
MOVFPE,
MOVTPE
—
—
—
—
—
—
—
B
—
—
—
—
—
Arithmetic ADD, CMP
operations SUB
BWL BWL —
—
—
—
—
—
—
—
—
—
—
WL
—
—
—
—
—
—
—
—
—
—
BWL —
ADDX, SUBX B
B
—
—
—
—
—
—
—
—
—
—
—
ADDS, SUBS —
L
—
—
—
—
—
—
—
—
—
—
—
INC, DEC
—
BWL —
—
—
—
—
—
—
—
—
—
—
DAA, DAS
—
B
—
—
—
—
—
—
—
—
—
—
—
DIVXU,
MULXS,
MULXU,
DIVXS
—
BW
—
—
—
—
—
—
—
—
—
—
—
NEG
—
BWL —
—
—
—
—
—
—
—
—
—
—
EXTU, EXTS
—
WL
—
—
—
—
—
—
—
—
—
—
—
BWL BWL —
—
—
—
—
—
—
—
—
—
—
—
Logic
AND, OR,
operations XOR
NOT
—
BWL —
—
—
—
—
—
—
—
—
—
Shift instructions
—
BWL —
—
—
—
—
—
—
—
—
—
—
Bit manipulation
—
B
—
—
—
B
—
—
—
—
—
—
Branch
System
control
B
Bcc, BSR
—
—
—
—
—
—
—
—
—
o
o
—
—
JMP, JSR
—
—
o
—
—
—
—
—
o
—
—
o
—
RTS
—
—
—
—
—
—
—
—
—
—
—
—
o
TRAPA
—
—
—
—
—
—
—
—
—
—
—
—
o
RTE
—
—
—
—
—
—
—
—
—
—
—
—
o
SLEEP
—
—
—
—
—
—
—
—
—
—
—
—
o
LDC
B
B
W
W
W
W
—
W
W
—
—
—
—
STC
—
B
W
W
W
W
—
W
W
—
—
—
—
ANDC, ORC,
XORC
B
—
—
—
—
—
—
—
—
—
—
—
—
NOP
—
—
—
—
—
—
—
—
—
—
—
—
o
—
—
—
—
—
—
—
—
—
—
—
—
BW
Block data transfer
Legend
B: Byte
W: Word
L: Longword
25
2.6.3 Tables of Instructions Classified by Function
Tables 2-3 to 2-10 summarize the instructions in each functional category. The operation notation
used in these tables is defined next.
Operation Notation
Rd
General register (destination)*
Rs
General register (source)*
Rn
General register*
ERn
General register (32-bit register or address register)
(EAd)
Destination operand
(EAs)
Source operand
CCR
Condition code register
N
N (negative) flag of CCR
Z
Z (zero) flag of CCR
V
V (overflow) flag of CCR
C
C (carry) flag of CCR
PC
Program counter
SP
Stack pointer
#IMM
Immediate data
disp
Displacement
+
Addition
–
Subtraction
×
Multiplication
÷
Division
∧
AND logical
∨
OR logical
⊕
Exclusive OR logical
→
Move
¬
NOT (logical complement)
:3/:8/:16/:24
3-, 8-, 16-, or 24-bit length
Note: * General registers include 8-bit registers (R0H to R7H, R0L to R7L), 16-bit registers (R0 to
R7, E0 to E7), and 32-bit data or address registers (ER0 to ER7).
26
Table 2-3 Data Transfer Instructions
Instruction Size*
Function
MOV
(EAs) →Rd, Rs →(EAd)
B/W/L
Moves data between two general registers or between a general register
and memory, or moves immediate data to a general register.
MOVFPE
B
(EAs) →Rd
Cannot be used in the H8/3004 and H8/3005.
MOVTPE
B
Rs →(EAs)
Cannot be used in the H8/3004 and H8/3005.
POP
W/L
@SP+ →Rn
Pops a general register from the stack. POP.W Rn is identical to MOV.W
@SP+, Rn. Similarly, POP.L ERn is identical to MOV.L @SP+, ERn.
PUSH
W/L
Rn →@–SP
Pushes a general register onto the stack. PUSH.W Rn is identical to MOV.W
Rn, @–SP. Similarly, PUSH.L ERn is identical to MOV.L ERn, @–SP.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
27
Table 2-4 Arithmetic Operation Instructions
Instruction Size*
Function
ADD,
SUB
B/W/L
Rd ± Rs →Rd, Rd ± #IMM →Rd
ADDX,
SUBX
B
INC,
DEC
B/W/L
ADDS,
SUBS
L
DAA,
DAS
B
MULXU
B/W
Performs addition or subtraction on data in two general registers, or on
immediate data and data in a general register. (Immediate byte data cannot
be subtracted from data in a general register. Use the SUBX or ADD
instruction.)
Rd ± Rs ± C →Rd, Rd ± #IMM ± C →Rd
Performs addition or subtraction with carry or borrow on data in two general
registers, or on immediate data and data in a general register.
Rd ± 1 →Rd, Rd ± 2 →Rd
Increments or decrements a general register by 1 or 2. (Byte operands can
be incremented or decremented by 1 only.)
Rd ± 1 →Rd, Rd ± 2 →Rd, Rd ± 4 →Rd
Adds or subtracts the value 1, 2, or 4 to or from data in a 32-bit register.
Rd decimal adjust →Rd
Decimal-adjusts an addition or subtraction result in a general register by
referring to CCR to produce 4-bit BCD data.
Rd ×Rs →Rd
Performs unsigned multiplication on data in two general registers: either
8 bits ×8 bits →16 bits or 16 bits ×16 bits →32 bits.
MULXS
B/W
Rd ×Rs →Rd
Performs signed multiplication on data in two general registers: either
8 bits ×8 bits →16 bits or 16 bits ×16 bits →32 bits.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
28
Table 2-4 Arithmetic Operation Instructions (cont)
Instruction Size*
Function
DIVXU
Rd ÷ Rs →Rd
B/W
Performs unsigned division on data in two general registers: either
16 bits ÷ 8 bits →8-bit quotient and 8-bit remainder or 32 bits ÷ 16 bits →16-bit
quotient and 16-bit remainder.
DIVXS
B/W
Rd ÷ Rs →Rd
Performs signed division on data in two general registers: either
16 bits ÷ 8 bits →8-bit quotient and 8-bit remainder, or 32 bits ÷ 16 bits →16bit quotient and 16-bit remainder.
CMP
B/W/L
Rd – Rs, Rd – #IMM
Compares data in a general register with data in another general register or
with immediate data, and sets CCR according to the result.
NEG
B/W/L
0 – Rd →Rd
Takes the two’s complement (arithmetic complement) of data in a general
register.
EXTS
W/L
Rd (sign extension) →Rd
Extends byte data in the lower 8 bits of a 16-bit register to word data, or
extends word data in the lower 16 bits of a 32-bit register to longword data,
by extending the sign bit.
EXTU
W/L
Rd (zero extension) →Rd
Extends byte data in the lower 8 bits of a 16-bit register to word data, or
extends word data in the lower 16 bits of a 32-bit register to longword data,
by padding with zeros.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
29
Table 2-5 Logic Operation Instructions
Instruction Size*
Function
AND
Rd ∧Rs →Rd, Rd ∧#IMM →Rd
B/W/L
Performs a logical AND operation on a general register and another general
register or immediate data.
OR
B/W/L
Rd ∨Rs →Rd, Rd ∨#IMM →Rd
Performs a logical OR operation on a general register and another general
register or immediate data.
XOR
B/W/L
Rd ⊕Rs →Rd, Rd ⊕#IMM →Rd
Performs a logical exclusive OR operation on a general register and another
general register or immediate data.
NOT
B/W/L
¬ Rd →Rd
Takes the one’s complement of general register contents.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
Table 2-6 Shift Instructions
Instruction Size*
Function
SHAL,
SHAR
B/W/L
Rd (shift) →Rd
SHLL,
SHLR
B/W/L
ROTL,
ROTR
B/W/L
ROTXL,
ROTXR
B/W/L
Performs an arithmetic shift on general register contents.
Rd (shift) →Rd
Performs a logical shift on general register contents.
Rd (rotate) →Rd
Rotates general register contents.
Rd (rotate) →Rd
Rotates general register contents through the carry bit.
Note: * Size refers to the operand size.
B: Byte
W: Word
L: Longword
30
Table 2-7 Bit Manipulation Instructions
Instruction Size*
Function
BSET
1 →(<bit-No.> of <EAd>)
B
Sets a specified bit in a general register or memory operand to 1. The bit
number is specified by 3-bit immediate data or the lower 3 bits of a general
register.
BCLR
B
0 →(<bit-No.> of <EAd>)
Clears a specified bit in a general register or memory operand to 0. The bit
number is specified by 3-bit immediate data or the lower 3 bits of a general
register.
BNOT
B
¬ (<bit-No.> of <EAd>) →(<bit-No.> of <EAd>)
Inverts a specified bit in a general register or memory operand. The bit
number is specified by 3-bit immediate data or the lower 3 bits of a general
register.
BTST
B
¬ (<bit-No.> of <EAd>) →Z
Tests a specified bit in a general register or memory operand and sets or
clears the Z flag accordingly. The bit number is specified by 3-bit immediate
data or the lower 3 bits of a general register.
BAND
B
C ∧(<bit-No.> of <EAd>) →C
ANDs the carry flag with a specified bit in a general register or memory
operand and stores the result in the carry flag.
BIAND
B
C ∧[¬ (<bit-No.> of <EAd>)] →C
ANDs the carry flag with the inverse of a specified bit in a general register or
memory operand and stores the result in the carry flag.
The bit number is specified by 3-bit immediate data.
Note: * Size refers to the operand size.
B: Byte
31
Table 2-7 Bit Manipulation Instructions (cont)
Instruction Size*
Function
BOR
C ∨(<bit-No.> of <EAd>) →C
B
ORs the carry flag with a specified bit in a general register or memory
operand and stores the result in the carry flag.
BIOR
B
C ∨[¬ (<bit-No.> of <EAd>)] →C
ORs the carry flag with the inverse of a specified bit in a general register or
memory operand and stores the result in the carry flag.
The bit number is specified by 3-bit immediate data.
BXOR
B
C ⊕(<bit-No.> of <EAd>) →C
Exclusive-ORs the carry flag with a specified bit in a general register or
memory operand and stores the result in the carry flag.
BIXOR
B
C ⊕[¬ (<bit-No.> of <EAd>)] →C
Exclusive-ORs the carry flag with the inverse of a specified bit in a general
register or memory operand and stores the result in the carry flag.
The bit number is specified by 3-bit immediate data.
BLD
B
(<bit-No.> of <EAd>) →C
Transfers a specified bit in a general register or memory operand to the
carry flag.
BILD
B
¬ (<bit-No.> of <EAd>) →C
Transfers the inverse of a specified bit in a general register or memory
operand to the carry flag.
The bit number is specified by 3-bit immediate data.
BST
B
C →(<bit-No.> of <EAd>)
Transfers the carry flag value to a specified bit in a general register or
memory operand.
BIST
B
C →¬ (<bit-No.> of <EAd>)
Transfers the inverse of the carry flag value to a specified bit in a general
register or memory operand.
The bit number is specified by 3-bit immediate data.
Note: * Size refers to the operand size.
B: Byte
32
Table 2-8 Branching Instructions
Instruction Size
Function
Bcc
Branches to a specified address if a specified condition is true. The
branching conditions are listed below.
—
Mnemonic
Description
Condition
BRA (BT)
Always (true)
Always
BRN (BF)
Never (false)
Never
BHI
High
C ∨Z = 0
BLS
Low or same
C ∨Z = 1
Bcc (BHS)
Carry clear (high or same)
C=0
BCS (BLO)
Carry set (low)
C=1
BNE
Not equal
Z=0
BEQ
Equal
Z=1
BVC
Overflow clear
V=0
BVS
Overflow set
V=1
BPL
Plus
N=0
BMI
Minus
N=1
BGE
Greater or equal
N ⊕V = 0
BLT
Less than
N ⊕V = 1
BGT
Greater than
Z ∨(N ⊕V) = 0
BLE
Less or equal
Z ∨(N ⊕V) = 1
JMP
—
Branches unconditionally to a specified address
BSR
—
Branches to a subroutine at a specified address
JSR
—
Branches to a subroutine at a specified address
RTS
—
Returns from a subroutine
33
Table 2-9 System Control Instructions
Instruction Size*
Function
TRAPA
—
Starts trap-instruction exception handling
RTE
—
Returns from an exception-handling routine
SLEEP
—
Causes a transition to the power-down state
LDC
B/W
(EAs) →CCR
Moves the source operand contents to the condition code register. The
condition code register size is one byte, but in transfer from memory, data is
read by word access.
STC
B/W
CCR →(EAd)
Transfers the CCR contents to a destination location. The condition code
register size is one byte, but in transfer to memory, data is written by word
access.
ANDC
B
CCR ∧#IMM →CCR
Logically ANDs the condition code register with immediate data.
ORC
B
CCR ∨#IMM →CCR
Logically ORs the condition code register with immediate data.
XORC
B
CCR ⊕#IMM →CCR
Logically exclusive-ORs the condition code register with immediate data.
NOP
—
PC + 2 →PC
Only increments the program counter.
Note: * Size refers to the operand size.
B: Byte
W: Word
34
Table 2-10 Block Transfer Instruction
Instruction Size
Function
EEPMOV.B
if R4L ≠ 0 then
repeat @ER5+ →@ER6+, R4L – 1 →R4L
until
R4L = 0
else next;
—
EEPMOV.W —
if R4 ≠ 0 then
repeat @ER5+ →@ER6+, R4 – 1 →R4
until
R4 = 0
else next;
Transfers a data block according to parameters set in general registers R4L
or R4, ER5, and ER6.
R4L or R4: Size of block (bytes)
ER5:
Starting source address
ER6:
Starting destination address
Execution of the next instruction begins as soon as the transfer is
completed.
35
2.6.4 Basic Instruction Formats
The H8/300H instructions consist of 2-byte (1-word) units. An instruction consists of an operation
field (OP field), a register field (r field), an effective address extension (EA field), and a condition
field (cc).
Operation Field: Indicates the function of the instruction, the addressing mode, and the operation
to be carried out on the operand. The operation field always includes the first 4 bits of the
instruction. Some instructions have two operation fields.
Register Field: Specifies a general register. Address registers are specified by 3 bits, data registers
by 3 bits or 4 bits. Some instructions have two register fields. Some have no register field.
Effective Address Extension: Eight, 16, or 32 bits specifying immediate data, an absolute
address, or a displacement. A 24-bit address or displacement is treated as 32-bit data in which the
first 8 bits are 0 (H'00).
Condition Field: Specifies the branching condition of Bcc instructions.
Figure 2-9 shows examples of instruction formats.
Operation field only
op
NOP, RTS, etc.
Operation field and register fields
op
rn
rm
ADD.B Rn, Rm, etc.
Operation field, register fields, and effective address extension
op
rn
rm
MOV.B @(d:16, Rn), Rm
EA (disp)
Operation field, effective address extension, and condition field
op
cc
EA (disp)
Figure 2-9 Instruction Formats
36
BRA d:8
2.6.5 Notes on Use of Bit Manipulation Instructions
The BSET, BCLR, BNOT, BST, and BIST instructions read a byte of data, modify a bit in the
byte, then write the byte back. Care is required when these instructions are used to access registers
with write-only bits, or to access ports.
The BCLR instruction can be used to clear flags in the on-chip registers. In an interrupt-handling
routine, for example, if it is known that the flag is set to 1, it is not necessary to read the flag ahead
of time.
2.7 Addressing Modes and Effective Address Calculation
2.7.1 Addressing Modes
The H8/300H CPU supports the eight addressing modes listed in table 2-11. Each instruction uses
a subset of these addressing modes. Arithmetic and logic instructions can use the register direct
and immediate modes. Data transfer instructions can use all addressing modes except programcounter relative and memory indirect. Bit manipulation instructions use register direct, register
indirect, or absolute (@aa:8) addressing mode to specify an operand, and register direct (BSET,
BCLR, BNOT, and BTST instructions) or immediate (3-bit) addressing mode to specify a bit
number in the operand.
Table 2-11 Addressing Modes
No.
Addressing Mode
Symbol
1
Register direct
Rn
2
Register indirect
@ERn
3
Register indirect with displacement
@(d:16, ERn)/@d:24, ERn)
4
Register indirect with post-increment
Register indirect with pre-decrement
@ERn+
@–ERn
5
Absolute address
@aa:8/@aa:16/@aa:24
6
Immediate
#xx:8/#xx:16/#xx:32
7
Program-counter relative
@(d:8, PC)/@(d:16, PC)
8
Memory indirect
@@aa:8
37
1 Register Direct—Rn: The register field of the instruction code specifies an 8-, 16-, or 32-bit
register containing the operand. R0H to R7H and R0L to R7L can be specified as 8-bit registers.
R0 to R7 and E0 to E7 can be specified as 16-bit registers. ER0 to ER7 can be specified as 32-bit
registers.
2 Register Indirect—@ERn: The register field of the instruction code specifies an address
register (ERn), the lower 24 bits of which contain the address of the operand.
3 Register Indirect with Displacement—@(d:16, ERn) or @(d:24, ERn): A 16-bit or 24-bit
displacement contained in the instruction code is added to the contents of an address register
(ERn) specified by the register field of the instruction, and the lower 24 bits of the sum specify the
address of a memory operand. A 16-bit displacement is sign-extended when added.
4 Register Indirect with Post-Increment or Pre-Decrement—@ERn+ or @–ERn:
•
Register indirect with post-increment—@ERn+
The register field of the instruction code specifies an address register (ERn) the lower 24 bits
of which contain the address of a memory operand. After the operand is accessed, 1, 2, or 4 is
added to the address register contents (32 bits) and the sum is stored in the address register.
The value added is 1 for byte access, 2 for word access, or 4 for longword access. For word or
longword access, the register value should be even.
•
Register indirect with pre-decrement—@–ERn
The value 1, 2, or 4 is subtracted from an address register (ERn) specified by the register field
in the instruction code, and the lower 24 bits of the result become the address of a memory
operand. The result is also stored in the address register. The value subtracted is 1 for byte
access, 2 for word access, or 4 for longword access. For word or longword access, the
resulting register value should be even.
5 Absolute Address—@aa:8, @aa:16, or @aa:24: The instruction code contains the absolute
address of a memory operand. The absolute address may be 8 bits long (@aa:8), 16 bits long
(@aa:16), or 24 bits long (@aa:24). For an 8-bit absolute address, the upper 16 bits are all
assumed to be 1 (H'FFFF). For a 16-bit absolute address the upper 8 bits are a sign extension. A
24-bit absolute address can access the entire address space. Table 2-12 indicates the accessible
address ranges.
38
Table 2-12 Absolute Address Access Ranges
Absolute
Address
1-Mbyte Modes
16-Mbyte Modes
8 bits (@aa:8)
H'FFF00 to H'FFFFF
(1048320 to 1048575)
H'FFFF00 to H'FFFFFF
(16776960 to 16777215)
16 bits (@aa:16)
H'00000 to H'07FFF,
H'F8000 to H'FFFFF
(0 to 32767, 1015808 to 1048575)
H'000000 to H'007FFF,
H'FF8000 to H'FFFFFF
(0 to 32767, 16744448 to 16777215)
24 bits (@aa:24)
H'00000 to H'FFFFF
(0 to 1048575)
H'000000 to H'FFFFFF
(0 to 16777215)
6 Immediate—#xx:8, #xx:16, or #xx:32: The instruction code contains 8-bit (#xx:8), 16-bit
(#xx:16), or 32-bit (#xx:32) immediate data as an operand.
The instruction codes of the ADDS, SUBS, INC, and DEC instructions contain immediate data
implicitly. The instruction codes of some bit manipulation instructions contain 3-bit immediate
data specifying a bit number. The TRAPA instruction code contains 2-bit immediate data
specifying a vector address.
7 Program-Counter Relative—@(d:8, PC) or @(d:16, PC): This mode is used in the Bcc and
BSR instructions. An 8-bit or 16-bit displacement contained in the instruction code is signextended to 24 bits and added to the 24-bit PC contents to generate a 24-bit branch address. The
PC value to which the displacement is added is the address of the first byte of the next instruction,
so the possible branching range is –126 to +128 bytes (–63 to +64 words) or –32766 to +32768
bytes (–16383 to +16384 words) from the branch instruction. The resulting value should be an
even number.
8 Memory Indirect—@@aa:8: This mode can be used by the JMP and JSR instructions. The
instruction code contains an 8-bit absolute address specifying a memory operand. This memory
operand contains a branch address. The memory operand is accessed by longword access. The
first byte of the memory operand is ignored, generating a 24-bit branch address. See figure 2-10.
The upper bits of the 8-bit absolute address are assumed to be 0 (H'0000), so the address range is
0 to 255 (H'000000 to H'0000FF). Note that the first part of this range is also the exception vector
area. For further details see section 5, Interrupt Controller.
39
Reserved
Specified by @aa:8
Branch address
Figure 2-10 Memory-Indirect Branch Address Specification
When a word-size or longword-size memory operand is specified, or when a branch address is
specified, if the specified memory address is odd, the least significant bit is regarded as 0. The
accessed data or instruction code therefore begins at the preceding address. See section 2.5.2,
Memory Data Formats.
2.7.2 Effective Address Calculation
Table 2-13 explains how an effective address is calculated in each addressing mode. In the
1-Mbyte operating modes the upper 4 bits of the calculated address are ignored in order to
generate a 20-bit effective address.
40
41
4
3
2
r
r
disp
r
op
r
Register indirect with pre-decrement
@–ERn
op
Register indirect with post-increment
@ERn+
Register indirect with post-increment
or pre-decrement
op
Register indirect with displacement
@(d:16, ERn)/@(d:24, ERn)
op
Register indirect (@ERn)
rm rn
Register direct (Rn)
1
op
Addressing Mode and
Instruction Format
No.
1, 2, or 4
General register contents
1, 2, or 4
General register contents
1 for a byte operand, 2 for a word
operand, 4 for a longword operand
31
31
disp
General register contents
General register contents
Sign extension
31
31
Effective Address Calculation
Table 2-13 Effective Address Calculation
0
0
0
0
23
23
23
23
Operand is general
register contents
Effective Address
0
0
0
0
42
7
6
5
No.
abs
abs
abs
IMM
op
disp
Program-counter relative
@(d:8, PC) or @(d:16, PC)
op
Immediate
#xx:8, #xx:16, or #xx:32
op
@aa:24
op
@aa:16
op
Absolute address
@aa:8
Addressing Mode and
Instruction Format
disp
PC contents
Sign
extension
23
Effective Address Calculation
Table 2-13 Effective Address Calculation (cont)
0
16 15
H'FFFF
8 7
23
Operand is immediate data
23
Sign
extension
23
23
Effective Address
0
0
0
0
43
abs
Register field
Operation field
Displacement
Immediate data
Absolute address
op
Memory indirect
@@aa:8
Addressing Mode and
Instruction Format
Legend
r, rm, rn:
op:
disp:
IMM:
abs:
8
No.
31
H'0000
8 7
Memory contents
23
Effective Address Calculation
Table 2-13 Effective Address Calculation (cont)
abs
0
0
23
Effective Address
0
2.8 Processing States
2.8.1 Overview
The H8/300H CPU has five processing states: the program execution state, exception-handling
state, power-down state, reset state, and bus-released state. The power-down state includes sleep
mode, software standby mode, and hardware standby mode. Figure 2-11 classifies the processing
states. Figure 2-13 indicates the state transitions.
Processing states
Program execution state
The CPU executes program instructions in sequence
Exception-handling state
A transient state in which the CPU executes a hardware sequence
(saving PC and CCR, fetching a vector, etc.) in response to a reset,
interrupt, or other exception
Reset state
The CPU and all on-chip supporting modules are initialized and halted
Power-down state
Sleep mode
The CPU is halted to conserve power
Software standby mode
Hardware standby mode
Figure 2-11 Processing States
44
2.8.2 Program Execution State
In this state the CPU executes program instructions in normal sequence.
2.8.3 Exception-Handling State
The exception-handling state is a transient state that occurs when the CPU alters the normal
program flow due to a reset, interrupt, or trap instruction. The CPU fetches a starting address from
the exception vector table and branches to that address. In interrupt and trap exception handling
the CPU references the stack pointer (ER7) and saves the program counter and condition code
register.
Types of Exception Handling and Their Priority: Exception handling is performed for resets,
interrupts, and trap instructions. Table 2-14 indicates the types of exception handling and their
priority. Trap instruction exceptions are accepted at all times in the program execution state.
Table 2-14 Exception Handling Types and Priority
Priority Type of Exception Detection Timing
Start of Exception Handling
High
Low
Reset
Synchronized with clock
Exception handling starts immediately
when RES changes from low to high
Interrupt
End of instruction
execution or end of
exception handling*
When an interrupt is requested,
exception handling starts at the end of
the current instruction or current
exception-handling sequence
Trap instruction
When TRAPA instruction
is executed
Exception handling starts when a trap
(TRAPA) instruction is executed
Note: * Interrupts are not detected at the end of the ANDC, ORC, XORC, and LDC instructions, or
immediately after reset exception handling.
Figure 2-12 classifies the exception sources. For further details about exception sources, vector
numbers, and vector addresses, see section 4, Exception Handling, and section 5, Interrupt
Controller.
45
Reset
External interrupts
Exception
sources
Interrupt
Internal interrupts (from on-chip supporting modules)
Trap instruction
Figure 2-12 Classification of Exception Sources
Program execution state
SLEEP
instruction
with SSBY = 0
End of
exception
handling
Exception
Sleep mode
SLEEP instruction
with SSBY = 1
Interrupt
Exception-handling state
NMI, IRQ 0 , IRQ 1,
or IRQ 2 interrupt
Software standby mode
RES = 1
STBY = 1, RES = 0
Reset state*1
*2
Hardware standby mode
Power-down state
Notes: 1. From any state except hardware standby mode, a transition to the reset state occurs
whenever RES goes low.
2. From any state, a transition to hardware standby mode occurs when STBY goes low.
Figure 2-13 State Transitions
46
2.8.4 Exception-Handling Sequences
Reset Exception Handling: Reset exception handling has the highest priority. The reset state is
entered when the RES signal goes low. Reset exception handling starts after that, when RES
changes from low to high. When reset exception handling starts the CPU fetches a start address
from the exception vector table and starts program execution from that address. All interrupts,
including NMI, are disabled during the reset exception-handling sequence and immediately after it
ends.
Interrupt Exception Handling and Trap Instruction Exception Handling: When these
exception-handling sequences begin, the CPU references the stack pointer (ER7) and pushes the
program counter and condition code register on the stack. Next, if the UE bit in the system control
register (SYSCR) is set to 1, the CPU sets the I bit in the condition code register to 1. If the UE bit
is cleared to 0, the CPU sets both the I bit and the UI bit in the condition code register to 1. Then
the CPU fetches a start address from the exception vector table and execution branches to that
address.
Figure 2-14 shows the stack after the exception-handling sequence.
SP–4
SP (ER7)
SP–3
SP+1
SP–2
SP+2
SP–1
SP+3
SP (ER7)
Stack area
Before exception
handling starts
CCR
PC
SP+4
Pushed on stack
Even
address
After exception
handling ends
Legend
CCR: Condition code register
SP:
Stack pointer
Notes: 1. PC is the address of the first instruction executed after the return from the
exception-handling routine.
2. Registers must be saved and restored by word access or longword access,
starting at an even address.
Figure 2-14 Stack Structure after Exception Handling
47
2.8.5 Reset State
When the RES input goes low all current processing stops and the CPU enters the reset state. The
I bit in the condition code register is set to 1 by a reset. All interrupts are masked in the reset state.
Reset exception handling starts when the RES signal changes from low to high.
The reset state can also be entered by a watchdog timer overflow. For details see section 10,
Watchdog Timer.
2.8.6 Power-Down State
In the power-down state the CPU stops operating to conserve power. There are three modes: sleep
mode, software standby mode, and hardware standby mode.
Sleep Mode: A transition to sleep mode is made if the SLEEP instruction is executed while the
SSBY bit is cleared to 0 in the system control register (SYSCR). CPU operations stop
immediately after execution of the SLEEP instruction, but the contents of CPU registers are
retained.
Software Standby Mode: A transition to software standby mode is made if the SLEEP
instruction is executed while the SSBY bit is set to 1 in SYSCR. The CPU and clock halt and all
on-chip supporting modules stop operating. The on-chip supporting modules are reset, but as long
as a specified voltage is supplied the contents of CPU registers and on-chip RAM are retained.
The I/O ports also remain in their existing states.
Hardware Standby Mode: A transition to hardware standby mode is made when the STBY input
goes low. As in software standby mode, the CPU and clock halt and the on-chip supporting
modules are reset, but as long as a specified voltage is supplied, on-chip RAM contents are
retained.
For further information see section 14, Power-Down State.
48
2.9 Basic Operational Timing
2.9.1 Overview
The H8/300H CPU operates according to the system clock (ø). The interval from one rise of the
system clock to the next rise is referred to as a “state.” A memory cycle or bus cycle consists of
two or three states. The CPU uses different methods to access on-chip memory, the on-chip
supporting modules, and the external address space. Access to the external address space can be
controlled by the bus controller.
2.9.2 On-Chip Memory Access Timing
On-chip memory is accessed in two states. The data bus is 16 bits wide, permitting both byte and
word access. Figure 2-15 shows the on-chip memory access cycle. Figure 2-16 indicates the pin
states.
Bus cycle
T1 state
T2 state
ø
Internal address bus
Address
Internal read signal
Internal data bus
(read access)
Read data
Internal write signal
Internal data bus
(write access)
Write data
Figure 2-15 On-Chip Memory Access Cycle
49
T1
T2
ø
Address bus
AS , RD, WR
Address
High
High impedance
D7 to D0
Figure 2-16 Pin States during On-Chip Memory Access
50
2.9.3 On-Chip Supporting Module Access Timing
The on-chip supporting modules are accessed in three states. The data bus is 8 or 16 bits wide,
depending on the register being accessed. Figure 2-17 shows the on-chip supporting module
access timing. Figure 2-18 indicates the pin states.
Bus cycle
T1 state
T2 state
T3 state
ø
Address
Address bus
Read
access
Internal read signal
Internal data bus
Read data
Internal write signal
Write
access
Internal data bus
Write data
Figure 2-17 Access Cycle for On-Chip Supporting Modules
51
T1
T2
T3
ø
Address bus
AS , RD, WR
Address
High
High impedance
D7 to D0
Figure 2-18 Pin States during Access to On-Chip Supporting Modules
2.9.4 Access to External Address Space
The external address space is divided into eight areas (areas 0 to 7). Bus-controller settings
determine whether each area is accessed via an 8-bit or 16-bit bus, and whether it is accessed in
two or three states. For details see section 6, Bus Controller.
52
Section 3 MCU Operating Modes
3.1 Overview
3.1.1 Operating Mode Selection
The H8/3004 and H8/3005 have two operating modes (modes 1 and 3) that are selected by the
mode pins (MD1 and MD0) as indicated in table 3-1.
Table 3-1 Operating Mode Selection
Mode Pins
Description
Operating Mode
MD1
MD0
Address Space
On-Chip RAM
—
0
0
—
—
Mode 1
0
1
1 Mbyte
Enabled*
—
1
0
—
—
Mode 3
1
1
16 Mbyte
Enabled*
Note: * If the RAM enable bit (RAME) in the system control register (SYSCR) is cleared to 0,
these addresses become external addresses.
For the address space size there are two choices: 1 Mbyte or 16 Mbyte.
Modes 1 and 3 are external expansion modes that enable an external memory peripheral device to
be accessed.
Modes 1 support a maximum address space of 1 Mbyte. Mode 3 supports a maximum address
space of 16 Mbytes.
The H8/3004 and H8/3005 can only be used in modes 1 and 3. The inputs at the mode pins must
select modes 1 and 3. The inputs at the mode pins must not be changed during operation.
53
3.1.2 Register Configuration
The H8/3004 and H8/3005 have a mode control register (MDCR) that indicates the inputs at the
mode pins (MD2 to MD0), and a system control register (SYSCR). Table 3-2 summarizes these
registers.
Table 3-2 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFF1
Mode control register
MDCR
R
Undetermined
H'FFF2
System control register
SYSCR
R/W
H'0B
Note: * The lower 16 bits of the address are indicated.
54
3.2 Mode Control Register (MDCR)
MDCR is an 8-bit read-only register that indicates the current operating mode of the H8/3004 and
H8/3005.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
MDS1
MDS0
Initial value
1
1
0
0
0
0
—*
—*
Read/Write
—
—
—
—
—
—
R
R
Reserved bits
Mode select 1 and 0
Bits indicating the current
operating mode
Note: * Determined by pins MD 1 and MD 0 .
Bits 7 and 6—Reserved: Read-only bits, always read as 1.
Bits 5 to 2—Reserved: Read-only bits, always read as 0.
Bits 1 and 0—Mode Select 1 and 0 (MDS1 and MDS0): These bits indicate the logic levels at
pins MD1 and MD0 (the current operating mode). MDS1 and MDS0 correspond to MD1 and
MD0. MDS1 and MDS0 are read-only bits. The mode pin (MD1 and MD0) levels are latched
when MDCR is read.
55
3.3 System Control Register (SYSCR)
SYSCR is an 8-bit register that controls the operation of the H8/3004 and H8/3005.
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
—
RAME
Initial value
0
0
0
0
1
0
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
—
R/W
RAM enable
Enables or
disables
on-chip RAM
Reserved bit
NMI edge select
Selects the valid edge
of the NMI input
User bit enable
Selects whether to use UI bit in CCR 6
as a user bit or an interrupt mask bit
Standby timer select 2 to 0
These bits select the waiting time at
recovery from software standby mode
Software standby
Enables transition to software standby mode
Bit 7—Software Standby (SSBY): Enables transition to software standby mode. (For further
information about software standby mode see section 14, Power-Down State.)
When software standby mode is exited by an external interrupt, this bit remains set to 1. To clear
this bit, write 0.
Bit 7
SSBY
Description
0
SLEEP instruction causes transition to sleep mode
1
SLEEP instruction causes transition to software standby mode
56
(Initial value)
Bits 6 to 4—Standby Timer Select (STS2 to STS0): These bits select the length of time the CPU
and on-chip supporting modules wait for the internal clock oscillator to settle when software
standby mode is exited by an external interrupt. Set these bits so that the waiting time will be at
least 8 ms at the system clock rate. For further information about waiting time selection, see
section 14.4.3, Selection of Waiting Time for Exit from Software Standby Mode.
Bit 6
STS2
Bit 5
STS1
Bit 4
STS0
Description
0
0
0
Waiting time = 8192 states
0
0
1
Waiting time = 16384 states
0
1
0
Waiting time = 32768 states
0
1
1
Waiting time = 65536 states
1
0
—
Waiting time = 131072 states
1
1
—
Illegal setting
(Initial value)
Bit 3—User Bit Enable (UE): Selects whether to use the UI bit in the condition code register as a
user bit or an interrupt mask bit.
Bit 3
UE
Description
0
UI bit in CCR is used as an interrupt mask bit
1
UI bit in CCR is used as a user bit
(Initial value)
Bit 2—NMI Edge Select (NMIEG): Selects the valid edge of the NMI input.
Bit 2
NMIEG
Description
0
An interrupt is requested at the falling edge of NMI
1
An interrupt is requested at the rising edge of NMI
(Initial value)
Bit 1—Reserved: Read-only bit, always read as 1.
Bit 0—RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is
initialized by the rising edge of the RES signal. It is not initialized in software standby mode.
Bit 0
RAME
Description
0
On-chip RAM is disabled
1
On-chip RAM is enabled
(Initial value)
57
3.4 Operating Mode Descriptions
3.4.1 Mode 1
Address pins A19 to A0 are enabled, and a maximum 1-Mbyte address space can be accessed.
3.4.2 Mode 3
Address pins A23 to A0 are enabled, and a maximum 16-Mbyte address space can be accessed.
3.5 Memory Map in Each Operating Mode
Figure 3-1 shows a memory map of H8/3004. Figure 3-2 shows a memory map of H8/3005. The
address space is divided into eight areas.
The on-chip RAM and internal I/O register layout differs between mode 1 (1-Mbyte mode) and
mode 3 (16-Mbyte mode). There is also a difference in the range that can be specified by an 8-bit
or 16-bit absolute address (@aa:8/@aa:16) in the CPU addressing mode.
58
Mode 1
(1 Mbyte mode)
H'000000
Vector table
16-bit absolute
addresses
Vector table
16-bit absolute
addresses
H'07FFF
H'007FFF
Area 0
H'1FFFFF
H'200000
H'3FFFFF
H'400000
H'5FFFFF
H'600000
External addresses
H'7FFFFF
H'800000
H'9FFFFF
H'A00000
H'BFFFFF
H'C00000
H'DFFFFF
H'E00000
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
H'FF8000
H'FF70F
H'FF710
H'FFF70F
H'FFF710
External addresses
H'FFF1B
H'FFF1C
On-chip register
H'FFFFF
8-bit absolute addresses
On-chip RAM*
H'FFF00
H'FFF0F
H'FFF10
16-bit absolute addresses
H'F8000
Area 0
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
On-chip RAM*
H'FFFF00
H'FFFF0F
H'FFFF10
External addresses
H'FFFF1B
H'FFFF1C
On-chip register
H'FFFFFF
Note: * Can be made external address space by clearing the RAME bit in SYSCR to 0.
Figure 3-1 H8/3004 Memory Map
59
8-bit absolute addresses
H'1FFFF
H'20000
H'3FFFF
H'40000
H'5FFFF
H'60000
External addresses
H'7FFFF
H'80000
H'9FFFF
H'A0000
H'BFFFF
H'C0000
H'DFFFF
H'E0000
16-bit absolute addresses
H'00000
Mode 3
(16 Mbytes mode)
Mode 1
(1 Mbyte mode)
H'000000
Vector table
16-bit absolute
addresses
Vector table
16-bit absolute
addresses
H'07FFF
H'007FFF
Area 0
H'1FFFFF
H'200000
H'3FFFFF
H'400000
H'5FFFFF
H'600000
External addresses
H'7FFFFF
H'800000
H'9FFFFF
H'A00000
H'BFFFFF
H'C00000
H'DFFFFF
H'E00000
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
H'FF8000
H'FEF0F
H'FEF10
H'FFEF0F
H'FFEF10
External addresses
H'FFF1B
H'FFF1C
On-chip register
H'FFFFF
8-bit absolute addresses
On-chip RAM*
H'FFF00
H'FFF0F
H'FFF10
16-bit absolute addresses
H'F8000
Area 0
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
On-chip RAM*
H'FFFF00
H'FFFF0F
H'FFFF10
External addresses
H'FFFF1B
H'FFFF1C
On-chip register
H'FFFFFF
Note: * Can be made external address space by clearing the RAME bit in SYSCR to 0.
Figure 3-2 H8/3005 Memory Map
60
8-bit absolute addresses
H'1FFFF
H'20000
H'3FFFF
H'40000
H'5FFFF
H'60000
External addresses
H'7FFFF
H'80000
H'9FFFF
H'A0000
H'BFFFF
H'C0000
H'DFFFF
H'E0000
16-bit absolute addresses
H'00000
Mode 3
(16 Mbytes mode)
Section 4 Exception Handling
4.1 Overview
4.1.1 Exception Handling Types and Priority
As table 4-1 indicates, exception handling may be caused by a reset, trap instruction, or interrupt.
Exception handling is prioritized as shown in table 4-1. If two or more exceptions occur
simultaneously, they are accepted and processed in priority order. Trap instruction exceptions are
accepted at all times in the program execution state.
Table 4-1 Exception Types and Priority
Priority Exception Type
Start of Exception Handling
High
Reset
Starts immediately after a low-to-high transition at the RES pin
Interrupt
Interrupt requests are handled when execution of the current
instruction or handling of the current exception is completed
Low
Trap instruction (TRAPA) Started by execution of a trap instruction (TRAPA)
4.1.2 Exception Handling Operation
Exceptions originate from various sources. Trap instructions and interrupts are handled as follows.
1.
The program counter (PC) and condition code register (CCR) are pushed onto the stack.
2.
The CCR interrupt mask bit is set to 1.
3.
A vector address corresponding to the exception source is generated, and program execution
starts from the address indicated in the vector address.
For a reset exception, steps 2 and 3 above are carried out.
61
4.1.3 Exception Vector Table
The exception sources are classified as shown in figure 4-1. Different vectors are assigned to
different exception sources. Table 4-2 lists the exception sources and their vector addresses.
• Reset
External interrupts: NMI, IRQ 0 to IRQ4
Exception
sources
• Interrupts
• Trap instruction
Internal interrupts: 21 interrupts from on-chip
supporting modules
Figure 4-1 Exception Sources
Table 4-2 Exception Vector Table
Exception Source
Reset
Reserved for system use
External interrupt (NMI)
Trap instruction (4 sources)
External interrupt
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
Reserved for system use
Internal interrupts*2
Vector Number
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
to
60
Vector Address*1
H'0000 to H'0003
H'0004 to H'0007
H'0008 to H'000B
H'000C to H'000F
H'0010 to H'0013
H'0014 to H'0017
H'0018 to H'001B
H'001C to H'001F
H'0020 to H'0023
H'0024 to H'0027
H'0028 to H'002B
H'002C to H'002F
H'0030 to H'0033
H'0034 to H'0037
H'0038 to H'003B
H'003C to H'003F
H'0040 to H'0043
H'0044 to H'0047
H'0048 to H'004B
H'004C to H'004F
H'0050 to H'0053
to
H'00F0 to H'00F3
Notes: 1. Lower 16 bits of the address.
2. For the internal interrupt vectors, see section 5.3.3, Interrupt Vector Table.
62
4.2 Reset
4.2.1 Overview
A reset is the highest-priority exception. When the RES pin goes low, all processing halts and the
H8/3004 and H8/3005 enter the reset state. A reset initializes the internal state of the CPU and the
registers of the on-chip supporting modules. Reset exception handling begins when the RES pin
changes from low to high.
The H8/3004 or H8/3005 can also be reset by overflow of the watchdog timer. For details see
section 10, Watchdog Timer.
4.2.2 Reset Sequence
The H8/3004 and H8/3005 enters the reset state when the RES pin goes low.
To ensure that the H8/3004 and H8/3005 are reset, hold the RES pin low for at least 20 ms at
power-up. To reset the H8/3004 and H8/3005 during operation, hold the RES pin low for at least
10 system clock (ø) cycles. See appendix D.2, Pin States at Reset, for the states of the pins in the
reset state.
When the RES pin goes high after being held low for the necessary time, the H8/3004 and
H8/3005 start reset exception handling as follows.
•
The internal state of the CPU and the registers of the on-chip supporting modules are
initialized, and the I bit is set to 1 in CCR.
•
The contents of the reset vector address (H'0000 to H'0003) are read, and program execution
starts from the address indicated in the vector address.
Figure 4-2 shows the reset sequence in modes 1 and 3.
63
Figure 4-2 Reset Sequence (Mode 1 and 3)
64
(2)
(4)
(3)
(6)
(5)
(8)
(7)
Address of reset vector ((1) = H'00000, (3) = H'00001, (5) = H'00002, (7) = H'00003)
Start address (contents of reset vector)
Start address
First instruction of program
High
(1)
Note: After a reset, the wait-state controller inserts three waite states in every bus cycle.
(1), (3), (5), (7)
(2), (4), (6), (8)
(9)
(10)
D7 to D0
WR
RD
Address
bus
RES
ø
Vector fetch
Internal
processing
(10)
(9)
Prefetch of
first program
instruction
4.2.3 Interrupts after Reset
If an interrupt is accepted after a reset but before the stack pointer (SP) is initialized, PC and CCR
will not be saved correctly, leading to a program crash. To prevent this, all interrupt requests,
including NMI, are disabled immediately after a reset. The first instruction of the program is
always executed immediately after the reset state ends. This instruction should initialize the stack
pointer (example: MOV.L #xx:32, SP).
4.3 Interrupts
Interrupt exception handling can be requested by nine external sources (NMI, IRQ0 to IRQ4) and
21 internal sources in the on-chip supporting modules. Figure 4-3 classifies the interrupt sources
and indicates the number of interrupts of each type.
The on-chip supporting modules that can request interrupts are the watchdog timer (WDT), 16-bit
integrated timer unit (ITU), serial communication interface (SCI), and A/D converter. Each
interrupt source has a separate vector address.
NMI is the highest-priority interrupt and is always accepted. Interrupts are controlled by the
interrupt controller. The interrupt controller can assign interrupts other than NMI to two priority
levels, and arbitrate between simultaneous interrupts. Interrupt priorities are assigned in interrupt
priority registers A and B (IPRA and IPRB) in the interrupt controller.
For details on interrupts see section 5, Interrupt Controller.
External interrupts
NMI (1)
IRQ 0 to IRQ 4 (5)
Internal interrupts
WDT* (1)
ITU (15)
SCI (4)
A/D converter (1)
Interrupts
Note: Numbers in parentheses are the number of interrupt sources.
* When the watchdog timer is used as an interval timer, it generates an interrupt
request at every counter overflow.
Figure 4-3 Interrupt Sources and Number of Interrupts
65
4.4 Trap Instruction
Trap instruction exception handling starts when a TRAPA instruction is executed. If the UE bit is
set to 1 in the system control register (SYSCR), the exception handling sequence sets the I bit to 1
in CCR. If the UE bit is 0, the I and UI bits are both set to 1. The TRAPA instruction fetches a
start address from a vector table entry corresponding to a vector number from 0 to 3, which is
specified in the instruction code.
4.5 Stack Status after Exception Handling
Figure 4-4 shows the stack after completion of trap instruction exception handling and interrupt
exception handling.
SP
CCR
PC
Note: In mode 1, the upper four bits of the PC are ignored, and the lower 20 bits become
the effective PC value.
Figure 4-4 Stack after Completion of Exception Handling
66
4.6 Notes on Stack Usage
When accessing word data or longword data, the H8/3004 and H8/3005 regard the lowest address
bit as 0. The stack should always be accessed by word access or longword access, and the value of
the stack pointer (SP, ER7) should always be kept even. Use the following instructions to save
registers:
PUSH.W Rn (or MOV.W Rn, @–SP)
PUSH.L ERn (or MOV.L ERn, @–SP)
Use the following instructions to restore registers:
POP.W Rn
POP.L ERn
(or MOV.W @SP+, Rn)
(or MOV.L @SP+, ERn)
Setting SP to an odd value may lead to a malfunction. Figure 4-5 shows an example of what
happens when the SP value is odd.
CCR
SP
RIL
SP
H'FFFEFA
H'FFFEFB
PC
PC
H'FFFEFC
H'FFFEFD
H'FFFEFF
SP
TRAPA instruction executed
SP set to H'FFFEFF
MOV. B RIL, @-ER7
Data saved above SP
CCR contents lost
Legend
CCR: Condition code register
PC: Program counter
R1L: General register R1L
SP: Stack pointer
Figure 4-5 Operation when SP Value is Odd
67
68
Section 5 Interrupt Controller
5.1 Overview
5.1.1 Features
The interrupt controller has the following features:
•
Interrupt priority registers (IPRs) for setting interrupt priorities
Interrupts other than NMI can be assigned to two priority levels on a module-by-module basis
in interrupt priority registers A and B (IPRA and IPRB).
•
Three-level masking by the I and UI bits in the CPU condition code register (CCR)
•
Independent vector addresses
All interrupts are independently vectored; the interrupt service routine does not have to
identify the interrupt source.
•
Six external interrupt pins
NMI has the highest priority and is always accepted; either the rising or falling edge can be
selected. For each of IRQ0 to IRQ4, sensing of the falling edge or level sensing can be
selected independently.
69
5.1.2 Block Diagram
Figure 5-1 shows a block diagram of the interrupt controller.
CPU
ISCR
IER
IPRA, IPRB
NMI
input
IRQ input
section ISR
IRQ input
OVF
TME
.
.
.
.
.
.
.
ADI
ADIE
Priority
decision logic
Interrupt
request
Vector
number
.
.
.
I
UI
Interrupt controller
UE
SYSCR
Legend
I:
IER:
IPRA:
IPRB:
ISCR:
ISR:
SYSCR:
UE:
UI:
Interrupt mask bit
IRQ enable register
Interrupt priority register A
Interrupt priority register B
IRQ sense control register
IRQ status register
System control register
User bit enable
User bit/interrupt mask bit
Figure 5-1 Interrupt Controller Block Diagram
70
CCR
5.1.3 Pin Configuration
Table 5-1 lists the interrupt pins.
Table 5-1 Interrupt Pins
Name
Abbreviation
I/O
Function
Nonmaskable interrupt
NMI
Input
Nonmaskable interrupt, rising edge or
falling edge selectable
Input
Maskable interrupts, falling edge or
level sensing selectable
External interrupt request 4 to 0 IRQ4 to IRQ0
5.1.4 Register Configuration
Table 5-2 lists the registers of the interrupt controller.
Table 5-2 Interrupt Controller Registers
Address*1
Name
Abbreviation
R/W
Initial Value
H'FFF2
System control register
SYSCR
R/W
H'0B
H'FFF4
IRQ sense control register
ISCR
R/W
H'00
H'FFF5
IRQ enable register
IER
R/W
H'00
H'FFF6
IRQ status register
ISR
R/(W)*2
H'00
H'FFF8
Interrupt priority register A
IPRA
R/W
H'00
H'FFF9
Interrupt priority register B
IPRB
R/W
H'00
Notes: 1. Lower 16 bits of the address.
2. Only 0 can be written, to clear flags.
71
5.2 Register Descriptions
5.2.1 System Control Register (SYSCR)
SYSCR is an 8-bit readable/writable register that controls software standby mode, selects the
action of the UI bit in CCR, selects the NMI edge, and enables or disables the on-chip RAM.
Only bits 3 and 2 are described here. For the other bits, see section 3.3, System Control Register
(SYSCR).
SYSCR is initialized to H'0B by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
—
RAME
Initial value
0
0
0
0
1
0
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RAM enable
Reserved bit
Standby timer
select 2 to 0
Software standby
NMI edge select
Selects the NMI input edge
User bit enable
Selects whether to use CCR bit 6
as a user bit or interrupt mask bit
72
Bit 3—User Bit Enable (UE): Selects whether to use the UI bit in CCR as a user bit or an
interrupt mask bit.
Bit 3
UE
Description
0
UI bit in CCR is used as interrupt mask bit
1
UI bit in CCR is used as user bit
(Initial value)
Bit 2—NMI Edge Select (NMIEG): Selects the NMI input edge.
Bit 2
NMIEG
Description
0
Interrupt is requested at falling edge of NMI input
1
Interrupt is requested at rising edge of NMI input
5.2.2 Interrupt Priority Registers A and B (IPRA, IPRB)
IPRA and IPRB are 8-bit readable/writable registers that control interrupt priority.
73
(Initial value)
Interrupt Priority Register A (IPRA): IPRA is an 8-bit readable/writable register in which
interrupt priority levels can be set.
Bit
7
6
5
4
3
2
1
0
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Priority
level A0
Selects the
priority level
of ITU
channel 2
interrupt
requests
Priority level A1
Selects the priority level
of ITU channel 1
interrupt requests
Priority level A2
Selects the priority level of
ITU channel 0 interrupt requests
Priority level A3
Selects the priority level of WDT
interrupt requests
Priority level A4
Selects the priority level of IRQ4
interrupt requests
Priority level A5
Selects the priority level of IRQ 2 and IRQ 3 interrupt requests
Priority level A6
Selects the priority level of IRQ1 interrupt requests
Priority level A7
Selects the priority level of IRQ 0 interrupt requests
IPRA is initialized to H'00 by a reset and in hardware standby mode.
74
Bit 7—Priority Level A7 (IPRA7): Selects the priority level of IRQ0 interrupt requests.
Bit 7
IPRA7
Description
0
IRQ0 interrupt requests have priority level 0 (low priority)
1
IRQ0 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 6—Priority Level A6 (IPRA6): Selects the priority level of IRQ1 interrupt requests.
Bit 6
IPRA6
Description
0
IRQ1 interrupt requests have priority level 0 (low priority)
1
IRQ1 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 5—Priority Level A5 (IPRA5): Selects the priority level of IRQ2 and IRQ3 interrupt
requests.
Bit 5
IPRA5
Description
0
IRQ2 and IRQ3 interrupt requests have priority level 0 (low priority)
1
IRQ2 and IRQ3 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 4—Priority Level A4 (IPRA4): Selects the priority level of IRQ4 interrupt requests.
Bit 4
IPRA4
Description
0
IRQ4 interrupt requests have priority level 0 (low priority)
1
IRQ4 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 3—Priority Level A3 (IPRA3): Selects the priority level of WDT interrupt requests.
Bit 3
IPRA3
Description
0
WDT interrupt requests have priority level 0 (low priority)
1
WDT interrupt requests have priority level 1 (high priority)
75
(Initial value)
Bit 2—Priority Level A2 (IPRA2): Selects the priority level of ITU channel 0 interrupt requests.
Bit 2
IPRA2
Description
0
ITU channel 0 interrupt requests have priority level 0 (low priority)
1
ITU channel 0 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 1—Priority Level A1 (IPRA1): Selects the priority level of ITU channel 1 interrupt requests.
Bit 1
IPRA1
Description
0
ITU channel 1 interrupt requests have priority level 0 (low priority)
1
ITU channel 1 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 0—Priority Level A0 (IPRA0): Selects the priority level of ITU channel 2 interrupt requests.
Bit 0
IPRA0
Description
0
ITU channel 2 interrupt requests have priority level 0 (low priority)
1
ITU channel 2 interrupt requests have priority level 1 (high priority)
76
(Initial value)
Interrupt Priority Register B (IPRB): IPRB is an 8-bit readable/writable register in which
interrupt priority levels can be set.
Bit
7
6
5
4
3
2
1
0
IPRB7
IPRB6
—
—
IPRB3
—
IPRB1
—
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bit
Priority level B1
Selects the priority level
of A/D converter
interrupt request
Reserved bit
Priority level B3
Selects the priority level of SCI
channel 0 interrupt requests
Reserved bits
Priority level B6
Selects the priority level of ITU channel 4 interrupt requests
Priority level B7
Selects the priority level of ITU channel 3 interrupt requests
IPRB is initialized to H'00 by a reset and in hardware standby mode.
77
Bit 7—Priority Level B7 (IPRB7): Selects the priority level of ITU channel 3 interrupt requests.
Bit 7
IPRB7
Description
0
ITU channel 3 interrupt requests have priority level 0 (low priority)
1
ITU channel 3 interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 6—Priority Level B6 (IPRB6): Selects the priority level of ITU channel 4 interrupt requests.
Bit 6
IPRB6
Description
0
ITU channel 4 interrupt requests have priority level 0 (low priority)
1
ITU channel 4 interrupt requests have priority level 1 (high priority)
(Initial value)
Bits 5 and 4—Reserved: These bits can be written and read, but it does not affect interrupt
priority.
Bit 3—Priority Level B3 (IPRB3): Selects the priority level of SCI interrupt requests.
Bit 3
IPRB3
Description
0
SCI interrupt requests have priority level 0 (low priority)
1
SCI interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 2—Reserved: This bit can be written and read, but it does not affect interrupt priority.
Bit 1—Priority Level B1 (IPRB1): Selects the priority level of A/D converter interrupt requests.
Bit 1
IPRB1
Description
0
A/D converter interrupt requests have priority level 0 (low priority)
1
A/D converter interrupt requests have priority level 1 (high priority)
(Initial value)
Bit 0—Reserved: This bit can be written and read, but it does not affect interrupt priority.
78
5.2.3 IRQ Status Register (ISR)
ISR is an 8-bit readable/writable register that indicates the status of IRQ0 to IRQ4 interrupt
requests.
Bit
7
6
5
4
3
2
1
0
—
—
—
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
Initial value
0
0
0
0
0
0
0
0
Read/Write
—
—
—
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
Reserved bits
IRQ 4 to IRQ0 flags
These bits indicate IRQ4 to IRQ0
interrupt request status
Note: * Only 0 can be written, to clear flags.
ISR is initialized to H'00 by a reset and in hardware standby mode.
Bits 7 to 5—Reserved: Read-only bits, always read as 0.
Bits 4 to 0—IRQ4 to IRQ0 Flags (IRQ4F to IRQ0F): These bits indicate the status of IRQ4 to
IRQ0 interrupt requests.
Bits 4 to 0
IRQ4F to IRQ0F
Description
0
[Clearing conditions]
(Initial value)
0 is written in IRQnF after reading the IRQnF flag when IRQnF = 1.
IRQnSC = 0, IRQn input is high, and interrupt exception handling is carried out.
IRQnSC = 1 and IRQn interrupt exception handling is carried out.
1
[Setting conditions]
IRQnSC = 0 and IRQn input is low.
IRQnSC = 1 and IRQn input changes from high to low.
Note: n = 4 to 0
79
5.2.4 IRQ Enable Register (IER)
IER is an 8-bit readable/writable register that enables or disables IRQ0 to IRQ4 interrupt requests.
Bit
7
6
5
4
3
2
1
0
—
—
—
IRQ4E
IRQ3E
IRQ2E
IRQ1E
IRQ0E
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bits
IRQ 4 to IRQ0 enable
These bits enable or disable
IRQ4 to IRQ0 interrupts
IER is initialized to H'00 by a reset and in hardware standby mode.
Bits 7 to 5—Reserved: These bits can be written and read, but they do not enable or disable
interrupts.
Bits 4 to 0—IRQ4 to IRQ0 Enable (IRQ7E to IRQ0E): These bits enable or disable IRQ4 to
IRQ0 interrupts.
Bits 4 to 0
IRQ4E to IRQ0E
Description
0
IRQ4 to IRQ0 interrupts are disabled
1
IRQ4 to IRQ0 interrupts are enabled
80
(Initial value)
5.2.5 IRQ Sense Control Register (ISCR)
ISCR is an 8-bit readable/writable register that selects level sensing or falling-edge sensing of the
inputs at pins IRQ4 to IRQ0.
Bit
7
6
5
4
3
2
1
0
—
—
—
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bit
IRQ4SC IRQ3SC IRQ2SC IRQ1SC IRQ0SC
IRQ 4 to IRQ0 sense control
These bits select level sensing or falling-edge
sensing for IRQ4 to IRQ0 interrupts
ISCR is initialized to H'00 by a reset and in hardware standby mode.
Bits 7 to 5—Reserved: These bits can be written and read, but they do not select level or fallingedge sensing.
Bits 4 to 0—IRQ4 to IRQ0 Sense Control (IRQ4SC to IRQ0SC): These bits selects whether
interrupts IRQ4 to IRQ0 are requested by level sensing of pins IRQ4 to IRQ0, or by falling-edge
sensing.
Bits 4 to 0
IRQ4SC to IRQ0SC
Description
0
Interrupts are requested when IRQ4 to IRQ0 inputs are low
1
Interrupts are requested by falling-edge input at IRQ4 to IRQ0
81
(Initial value)
5.3 Interrupt Sources
The interrupt sources include external interrupts (NMI, IRQ0 to IRQ4) and 21 internal interrupts.
5.3.1 External Interrupts
There are six external interrupts: NMI, and IRQ0 to IRQ4. Of these, NMI, IRQ0, IRQ1, and IRQ2
can be used to exit software standby mode.
NMI: NMI is the highest-priority interrupt and is always accepted, regardless of the states of the
I and UI bits in CCR. The NMIEG bit in SYSCR selects whether an interrupt is requested by the
rising or falling edge of the input at the NMI pin. NMI interrupt exception handling has vector
number 7.
IRQ0 to IRQ4 Interrupts: These interrupts are requested by input signals at pins IRQ0 to IRQ4.
The IRQ0 to IRQ4 interrupts have the following features.
•
ISCR settings can select whether an interrupt is requested by the low level of the input at pins
IRQ0 to IRQ4, or by the falling edge.
•
IER settings can enable or disable the IRQ0 to IRQ4 interrupts. Interrupt priority levels can be
assigned by four bits in IPRA (IPRA7 to IPRA4).
•
The status of IRQ0 to IRQ4 interrupt requests is indicated in ISR. The ISR flags can be
cleared to 0 by software.
Figure 5-2 shows a block diagram of interrupts IRQ0 to IRQ4.
IRQnSC
IRQnE
IRQnF
Edge/level
sense circuit
S
Q
R
IRQn input
Clear signal
Note: n = 4 to 0
Figure 5-2 Block Diagram of Interrupts IRQ0 to IRQ4
82
IRQn interrupt
request
Figure 5-3 shows the timing of the setting of the interrupt flags (IRQnF).
ø
IRQn
input pin
IRQnF
Note: n = 4 to 0
Figure 5-3 Timing of Setting of IRQnF
Interrupts IRQ0 to IRQ4 have vector numbers 12 to 16. These interrupts are detected regardless of
whether the corresponding pin is set for input or output. When using a pin for external interrupt
input, clear its DDR bit to 0 and do not use the pin for SCI input or output.
5.3.2 Internal Interrupts
Twenty-one internal interrupts are requested from the on-chip supporting modules.
•
Each on-chip supporting module has status flags for indicating interrupt status, and enable
bits for enabling or disabling interrupts.
•
Interrupt priority levels can be assigned in IPRA and IPRB.
5.3.3 Interrupt Vector Table
Table 5-3 lists the interrupt sources, their vector addresses, and their default priority order. In the
default priority order, smaller vector numbers have higher priority. The priority of interrupts other
than NMI can be changed in IPRA and IPRB. The priority order after a reset is the default order
shown in table 5-3.
83
Table 5-3 Interrupt Sources, Vector Addresses, and Priority
Interrupt Source
Origin
Vector
Number
Vector Address*
IPR
Priority
NMI
External pins
7
H'001C to H'001F
—
High
IRQ0
IRQ1
12
H'0030 to H'0033
IPRA7
13
H'0034 to H0037
IPRA6
IRQ2
IRQ3
14
H'0038 to H'003B
IPRA5
15
H'003C to H'003F
IRQ4
Reserved
16
H'0040 to H'0043
17
H'0044 to H'0047
—
18
H'0048 to H'004B
19
H'004C to H'004F
WOVI (interval timer)
Watchdog timer
20
H'0050 to H'0053
Reserved
—
21
H'0054 to H'0057
22
H'0058 to H'005B
23
H'005C to H'005F
24
H'0060 to H'0063
IMIB0 (compare match/
input capture B0)
25
H'0064 to H'0067
OVI0 (overflow 0)
26
H'0068 to H'006B
IMIA0 (compare match/
input capture A0)
ITU channel 0
Reserved
—
27
H'006C to H'006F
IMIA1 (compare match/
input capture A1)
ITU channel 1
28
H'0070 to H'0073
29
H'0074 to H'0077
IMIB1 (compare match/
input capture B1)
OVI1 (overflow 1)
30
H'0078 to H'007B
Reserved
—
31
H'007C to H'007F
IMIA2 (compare match/
input capture A2)
ITU channel 2
32
H'0080 to H'0083
IMIB2 (compare match/
input capture B2)
33
H'0084 to H'0087
OVI2 (overflow 2)
34
H'0088 to H'008B
Reserved
—
35
Note: * Lower 16 bits of the address.
84
H'008C to H'008F
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
Table 5-3 Interrupt Sources, Vector Addresses, and Priority (cont)
Interrupt Source
Origin
Vector
Number
Vector Address*
IPR
IMIA3 (compare match/
input capture A3)
ITU channel 3
36
H'0090 to H'0093
IPRB7
IMIB3 (compare match/
input capture B3)
37
H'0094 to H'0097
OVI3 (overflow 3)
38
H'0098 to H'009B
Reserved
—
39
H'009C to H'009F
IMIA4 (compare match/
input capture A4)
ITU channel 4
40
H'00A0 to H'00A3
IMIB4 (compare match/
input capture B4)
41
H'00A4 to H'00A7
OVI4 (overflow 4)
42
H'00A8 to H'00AB
Reserved
—
43
H'00AC to H'00AF
Reserved
—
44
H'00B0 to H'00B3
45
H'00B4 to H'00B7
46
H'00B8 to H'00BB
47
H'00BC to H'00BF
48
H'00C0 to H'00C3
49
H'00C4 to H'00C7
50
H'00C8 to H'00CB
51
H'00CC to H'00CF
52
H'00D0 to H'00D3
RXI0 (receive data
full)
53
H'00D4 to H'00D7
TXI0 (transmit data
empty)
54
H'00D8 to H'00DB
TEI0 (transmit end)
55
H'00DC to H'00DF
56
H'00E0 to H'00E3
57
H'00E4 to H'00E7
58
H'00E8 to H'00EB
59
H'00EC to H'00EF
60
H'00F0 to H'00F3
ERI0 (receive error)
Reserved
ADI (A/D end)
SCI
—
A/D
Note: * Lower 16 bits of the address.
85
Priority
IPRB6
—
IPRB3
—
IPRB1
Low
5.4 Interrupt Operation
5.4.1 Interrupt Handling Process
The H8/3004 and H8/3005 handle interrupts differently depending on the setting of the UE bit.
When UE = 1, interrupts are controlled by the I bit. When UE = 0, interrupts are controlled by the
I and UI bits. Table 5-4 indicates how interrupts are handled for all setting combinations of the
UE, I, and UI bits.
NMI interrupts are always accepted except in the reset and hardware standby states. IRQ
interrupts and interrupts from the on-chip supporting modules have their own enable bits. Interrupt
requests are ignored when the enable bits are cleared to 0.
Table 5-4 UE, I, and UI Bit Settings and Interrupt Handling
SYSCR
CCR
UE
I
UI
Description
1
0
—
All interrupts are accepted. Interrupts with priority level 1 have higher
priority.
1
—
No interrupts are accepted except NMI.
0
—
All interrupts are accepted. Interrupts with priority level 1 have higher
priority.
1
0
NMI and interrupts with priority level 1 are accepted.
1
No interrupts are accepted except NMI.
0
UE = 1: Interrupts IRQ0 to IRQ4 and interrupts from the on-chip supporting modules can all be
masked by the I bit in the CPU’s CCR. Interrupts are masked when the I bit is set to 1, and
unmasked when the I bit is cleared to 0. Interrupts with priority level 1 have higher priority. Figure
5-4 is a flowchart showing how interrupts are accepted when UE = 1.
86
Program execution state
No
Interrupt requested?
Yes
Yes
NMI
No
No
Pending
Priority level 1?
Yes
IRQ 0
No
Yes
IRQ 1
IRQ 0
No
Yes
No
IRQ 1
Yes
No
Yes
ADI
ADI
Yes
Yes
No
I=0
Yes
Save PC and CCR
I ←1
Read vector address
Branch to interrupt
service routine
Figure 5-4 Process Up to Interrupt Acceptance when UE = 1
87
•
If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an
interrupt request is sent to the interrupt controller.
•
When the interrupt controller receives one or more interrupt requests, it selects the highestpriority request, following the IPR interrupt priority settings, and holds other requests
pending. If two or more interrupts with the same IPR setting are requested simultaneously, the
interrupt controller follows the priority order shown in table 5-3.
•
The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt
request is accepted. If the I bit is set to 1, only NMI is accepted; other interrupt requests are
held pending.
•
When an interrupt request is accepted, interrupt exception handling starts after execution of
the current instruction has been completed.
•
In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is
saved indicates the address of the first instruction that will be executed after the return from
the interrupt service routine.
•
Next the I bit is set to 1 in CCR, masking all interrupts except NMI.
•
The vector address of the accepted interrupt is generated, and the interrupt service routine
starts executing from the address indicated by the contents of the vector address.
UE = 0: The I and UI bits in the CPU’s CCR and the IPR bits enable three-level masking of IRQ0
to IRQ4 interrupts and interrupts from the on-chip supporting modules.
•
Interrupt requests with priority level 0 are masked when the I bit is set to 1, and are unmasked
when the I bit is cleared to 0.
•
Interrupt requests with priority level 1 are masked when the I and UI bits are both set to 1,
and are unmasked when either the I bit or the UI bit is cleared to 0.
For example, if the interrupt enable bits of all interrupt requests are set to 1, IPRA is set to
H'20, and IPRB is set to H'00 (giving IRQ2 and IRQ3 interrupt requests priority over other
interrupts), interrupts are masked as follows:
a. If I = 0, all interrupts are unmasked (priority order: NMI > IRQ2 > IRQ3 >IRQ0 …).
b. If I = 1 and UI = 0, only NMI, IRQ2, and IRQ3 are unmasked.
c. If I = 1 and UI = 1, all interrupts are masked except NMI.
88
Figure 5-5 shows the transitions among the above states.
I←0
a. All interrupts are
unmasked
I←0
b. Only NMI, IRQ 2 , and
IRQ 3 are unmasked
I ← 1, UI ← 0
Exception handling,
or I ← 1, UI ← 1
UI ← 0
Exception handling,
or UI ← 1
c. All interrupts are
masked except NMI
Figure 5-5 Interrupt Masking State Transitions (Example)
Figure 5-6 is a flowchart showing how interrupts are accepted when UE = 0.
•
If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an
interrupt request is sent to the interrupt controller.
•
When the interrupt controller receives one or more interrupt requests, it selects the highestpriority request, following the IPR interrupt priority settings, and holds other requests
pending. If two or more interrupts with the same IPR setting are requested simultaneously, the
interrupt controller follows the priority order shown in table 5-3.
•
The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt
request is accepted regardless of its IPR setting, and regardless of the UI bit. If the I bit is set
to 1 and the UI bit is cleared to 0, only NMI and interrupts with priority level 1 are accepted;
interrupt requests with priority level 0 are held pending. If the I bit and UI bit are both set to
1, only NMI is accepted; all other interrupt requests are held pending.
•
When an interrupt request is accepted, interrupt exception handling starts after execution of
the current instruction has been completed.
•
In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is
saved indicates the address of the first instruction that will be executed after the return from
the interrupt service routine.
•
The I and UI bits are set to 1 in CCR, masking all interrupts except NMI.
•
The vector address of the accepted interrupt is generated, and the interrupt service routine
starts executing from the address indicated by the contents of the vector address.
89
Program execution state
No
Interrupt requested?
Yes
Yes
NMI
No
No
Pending
Priority level 1?
Yes
IRQ 0
No
IRQ 0
Yes
IRQ 1
No
Yes
No
IRQ 1
Yes
No
Yes
ADI
ADI
Yes
Yes
No
I=0
No
I=0
Yes
Yes
No
UI = 0
Yes
Save PC and CCR
I ← 1, UI ← 1
Read vector address
Branch to interrupt
service routine
Figure 5-6 Process Up to Interrupt Acceptance when UE = 0
90
91
(2)
(4)
High
(1) (1)+1 (3)
(3)+1
Instruction Internal
prefetch
processing
Vector fetch
(8)
(10)
(12)
(11)+1
(14)
(13) (13)+1
Prefetch of
interrupt
Internal
service routine
processing instruction
(6), (8)
PC and CCR saved to stack
(9), (11) Vector address
(10), (12) Starting address of interrupt service routine (contents of
vector address)
(13)
Starting address of interrupt service routine; (13) = (10), (12)
(14)
First instruction of interrupt service routine
(6)
(5) (5)+1 (7) (7)+1 (9) (9)+1 (11)
Stack
Note: Mode 1, with program code and stack in external memory area: 2 states access.
(1)
Instruction prefetch address (not executed;
return address, same as PC contents)
(2), (4) Instruction code (not executed)
Instruction prefetch address (not executed)
(3)
SP – 2
(5)
SP – 4
(7)
On-chip
data
WR
RD
A19 to A 0
Interrupt
request
signal
ø
Interrupt level
decision and wait
for end of instruction
Interrupt accepted
5.4.2 Interrupt Sequence
Figure 5-7 shows the interrupt sequence in mode 1 when the program code and stack are in a
external memory area.
Figure 5-7 Interrupt Sequence (Mode 1, Stack in External Memory:
2 States Access)
5.4.3 Interrupt Response Time
Table 5-5 indicates the interrupt response time from the occurrence of an interrupt request until
the first instruction of the interrupt service routine is executed.
Table 5-5 Interrupt Response Time
External Memory
8-Bit Bus
Item
On-Chip
Memory
2 States
3 States
1
Interrupt priority decision
2*1
2*1
2*1
2
Maximum number of states
until end of current instruction
1 to 23
1 to 27
1 to 31*4
3
Saving PC and CCR to stack
4
8
12*4
4
Vector fetch
4
8
12*4
5
Instruction prefetch*2
4
8
12*4
6
Internal processing*3
4
4
4
19 to 41
31 to 57
43 to 73
No.
Total
Notes: 1. 1 state for internal interrupts.
2. Prefetch after the interrupt is accepted and prefetch of the first instruction in the interrupt
service routine.
3. Internal processing after the interrupt is accepted and internal processing after prefetch.
4. The number of states increases if wait states are inserted in external memory access.
92
5.5 Usage Notes
5.5.1 Contention between Interrupt and Interrupt-Disabling Instruction
When an instruction clears an interrupt enable bit to 0 to disable the interrupt, the interrupt is not
disabled until after execution of the instruction is completed. If an interrupt occurs while a BCLR,
MOV, or other instruction is being executed to clear its interrupt enable bit to 0, at the instant
when execution of the instruction ends the interrupt is still enabled, so its interrupt exception
handling is carried out. If a higher-priority interrupt is also requested, however, interrupt exception
handling for the higher-priority interrupt is carried out, and the lower-priority interrupt is ignored.
This also applies to the clearing of an interrupt flag.
Figure 5-8 shows an example in which an IMIEA bit is cleared to 0 in the ITU.
TIER write cycle by CPU
IMIA exception handling
ø
Internal
address bus
TIER address
Internal
write signal
IMIEA
IMIA
IMFA interrupt
signal
Figure 5-8 Contention between Interrupt and Interrupt-Disabling Instruction
This type of contention will not occur if the interrupt is masked when the interrupt enable bit or
flag is cleared to 0.
93
5.5.2 Instructions that Inhibit Interrupts
The LDC, ANDC, ORC, and XORC instructions inhibit interrupts. When an interrupt occurs,
after determining the interrupt priority, the interrupt controller requests a CPU interrupt. If the
CPU is currently executing one of these interrupt-inhibiting instructions, however, when the
instruction is completed the CPU always continues by executing the next instruction.
5.5.3 Interrupts during EEPMOV Instruction Execution
The EEPMOV.B and EEPMOV.W instructions differ in their reaction to interrupt requests.
When the EEPMOV.B instruction is executing a transfer, no interrupts are accepted until the
transfer is completed, not even NMI.
When the EEPMOV.W instruction is executing a transfer, interrupt requests other than NMI are
not accepted until the transfer is completed. If NMI is requested, NMI exception handling starts at
a transfer cycle boundary. The PC value saved on the stack is the address of the next instruction.
Programs should be coded as follows to allow for NMI interrupts during EEPMOV.W execution:
L1: EEPMOV.W
MOV.W R4,R4
BNE L1
94
Section 6 Bus Controller
6.1 Overview
The H8/3004 and H8/3005 have an on-chip bus controller that divides the external address space
into eight areas and can assign different bus specifications to each. This enables different types of
memory to be connected easily.
A bus arbitration function of the bus controller controls the operation of the DMA controller
(DMAC) and refresh controller. The bus controller can also release the bus to an external device.
6.1.1 Features
Features of the bus controller are listed below.
•
Independent settings for address areas 0 to 7
— 128-kbyte areas in 1-Mbyte mode, or 2-Mbyte areas in 16-Mbyte mode.
— Areas can be designated for two-state or three-state access.
•
Four wait modes
— Programmable wait mode, pin auto-wait mode, and pin wait modes 0 and 1 can be
selected.
— Zero to three wait states can be inserted automatically.
95
6.1.2 Block Diagram
Figure 6-1 shows a block diagram of the bus controller.
ASTCR
WCER
Area
decoder
Bus control
circuit
WAIT
Internal data bus
Internal
address bus
Internal signals
Access state control signal
Wait request signal
Wait-state
controller
WCR
Legend
ASTCR: Access state control register
WCER: Wait state controller enable register
WCR:
Wait control register
Figure 6-1 Block Diagram of Bus Controller
96
6.1.3 Input/Output Pins
Table 6-1 summarizes the bus controller’s input/output pins.
Table 6-1 Bus Controller Pins
Name
Abbreviation
I/O
Function
Address strobe
AS
Output
Strobe signal indicating valid address output on the
address bus
Read
RD
Output
Strobe signal indicating reading from the external
address space
Write
WR
Output
Strobe signal indicating writing to the external
address space, with valid data on the data bus
Wait
WAIT
Input
Wait request signal for access to external threestate-access areas
6.1.4 Register Configuration
Table 6-2 summarizes the bus controller’s registers.
Table 6-2 Bus Controller Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFED
Access state control register
ASTCR
R/W
H'FF
H'FFEE
Wait control register
WCR
R/W
H'F3
H'FFEF
Wait state controller enable register
WCER
R/W
H'FF
Note: * Lower 16 bits of the address.
97
6.2 Register Descriptions
6.2.1 Wait Control Register (WCR)
WCR is an 8-bit readable/writable register that selects the wait mode for the wait-state controller
(WSC) and specifies the number of wait states.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
WMS1
WMS0
WC1
WC0
Initial value
1
1
1
1
0
0
1
1
Read/Write
—
—
—
—
R/W
R/W
R/W
R/W
Reserved bits
Wait count 1/0
These bits select the
number of wait states
inserted
Wait mode select 1/0
These bits select the wait mode
WCR is initialized to H'F3 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 4—Reserved: Read-only bits, always read as 1.
Bits 3 and 2—Wait Mode Select 1 and 0 (WMS1/0): These bits select the wait mode.
Bit 3
WMS1
Bit 2
WMS0
Description
0
0
Programmable wait mode
1
No wait states inserted by wait-state controller
0
Pin wait mode 1
1
Pin auto-wait mode
1
(Initial value)
98
Bits 1 and 0—Wait Count 1 and 0 (WC1/0): These bits select the number of wait states inserted
in access to external three-state-access areas.
Bit 1
WC1
Bit 0
WC0
Description
0
0
No wait states inserted by wait-state controller
1
1 state inserted
0
2 states inserted
1
3 states inserted
1
(Initial value)
6.2.2 Access State Control Register (ASTCR)
ASTCR is an 8-bit readable/writable register that selects whether each area is accessed in two
states or three states.
Bit
7
6
5
4
3
2
1
0
AST7
AST6
AST5
AST4
AST3
AST2
AST1
AST0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bits selecting number of states for access to each area
ASTCR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 0—Area 7 to 0 Access State Control (AST7 to AST0): These bits select whether the
corresponding area is accessed in two or three states.
Bits 7 to 0
AST7 to AST0
Description
0
Areas 7 to 0 are accessed in two states
1
Areas 7 to 0 are accessed in three states
(Initial value)
ASTCR specifies the number of states in which external areas are accessed. On-chip memory and
registers are accessed in a fixed number of states that does not depend on ASTCR settings.
99
6.2.3 Wait State Controller Enable Register (WCER)
WCER is an 8-bit readable/writable register that enables or disables wait-state control of external
three-state-access areas by the wait-state controller.
Bit
7
6
5
4
3
2
1
0
WCE7
WCE6
WCE5
WCE4
WCE3
WCE2
WCE1
WCE0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Wait state controller enable 7 to 0
These bits enable or disable wait-state control
WCER is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bits 7 to 0—Wait-State Controller Enable 7 to 0 (WCE7 to WCE0): These bits enable or
disable wait-state control of external three-state-access areas.
Bits 7 to 0
WCE7 to WCE0
Description
0
Wait-state control disabled (pin wait mode 0)
1
Wait-state control enabled
(Initial value)
100
6.3 Operation
6.3.1 Area Division
The external address space is divided into areas 0 to 7. Each area has a size of 128 kbytes in the
1-Mbyte mode, or 2 Mbytes in the 16-Mbyte mode. Figure 6-2 shows a general view of the
memory map.
H'00000
H'000000
Area 0 (128 kbytes)
Area 0 (2 Mbytes)
H'1FFFF
H'1FFFFF
H'20000
H'200000
Area 1 (128 kbytes)
Area 1 (2 Mbytes)
H'3FFFF
H'3FFFFF
H'40000
H'400000
Area 2 (128 kbytes)
Area 2 (2 Mbytes)
H'5FFFF
H'60000
H'5FFFFF
H'600000
Area 3 (128 kbytes)
Area 3 (2 Mbytes)
H'7FFFF
H'7FFFFF
H'80000
H'800000
Area 4 (128 kbytes)
Area 4 (2 Mbytes)
H'9FFFF
H'9FFFFF
H'A0000
H'A00000
Area 5 (128 kbytes)
Area 5 (2 Mbytes)
H'BFFFF
H'BFFFFF
H'C0000
H'C00000
Area 6 (128 kbytes)
H'DFFFF
H'E0000
Area 6 (2 Mbytes)
H'DFFFFF
H'E00000
Area 7 (128 kbytes)
Area 7 (2 Mbytes)
*1, *2
On-chip RAM*1, *2
On-chip RAM
External address space*3
H'FFFFF
External address space*3
On-chip I/O registers*1
On-chip I/O registers*1
H'FFFFFF
(a) 1-Mbyte mode (mode 1)
(b) 16-Mbyte mode (mode 3)
Notes: 1. The number of access states to on-chip ROM, on-chip RAM, and on-chip I/O registers is fixed.
2. This area follows area 7 specifications when the RAME bit in SYSCR is 0.
3. This area follows area 7 specifications.
Figure 6-2 Access Area Map
101
The bus specifications for each area can be selected in ASTCR, WCER, and WCR as shown in
table 6-3.
Table 6-3 Bus Specifications
ASTCR
WCER
WCR
ASTn
WCEn
WMS1
WMS0
Bus
Width
Access
States
Wait Mode
0
—
—
—
8
2
Disabled
1
0
—
—
8
3
Pin wait mode 0
1
0
0
8
3
Programmable wait mode
1
8
3
Disabled
0
8
3
Pin wait mode 1
1
8
3
Pin auto-wait mode
1
Bus Specifications
Note: n = 0 to 7
102
6.3.2 Bus Control Signal Timing
Three-State-Access Areas: Figure 6-3 shows the timing of bus control signals for a three-stateaccess area. Wait states can be inserted.
Bus cycle
T1
T2
T3
ø
Address bus
Area n external address
AS
RD
Read
access
Valid
D7 to D0
WR
Write
access
Valid
D7 to D0
Note: n = 7 to 0
Figure 6-3 Bus Control Signal Timing for Three-State-Access Area
103
Two-State-Access Areas: Figure 6-4 shows the timing of bus control signals for a two-stateaccess area. Wait status cannot be inserted.
Bus cycle
T1
T2
ø
Address bus
Area n external address
AS
RD
Read
access
D7 to D0
Valid
WR
Write
access
D7 to D0
Valid
Note: n = 7 to 0
Figure 6-4 Bus Control Signal Timing for Two-State-Access Area
104
6.3.3 Wait Modes
Four wait modes can be selected for each area as shown in table 6-4.
Table 6-4 Wait Mode Selection
ASTCR
WCER
WCR
ASTn Bit WCEn Bit WMS1 Bit WMS0 Bit WSC Control
Wait Mode
0
—
—
—
Disabled
No wait states
1
0
—
—
Disabled
Pin wait mode 0
1
0
0
Enabled
Programmable wait mode
1
Enabled
No wait states
0
Enabled
Pin wait mode 1
1
Enabled
Pin auto-wait mode
1
Note: n = 7 to 0
The ASTn and WCEn bits can be set independently for each area. Bits WMS1 and WMS0 apply
to all areas. All areas for which WSC control is enabled operate in the same wait mode.
105
Pin Wait Mode 0: The wait state controller is disabled. Wait states can only be inserted by WAIT
pin control. During access to an external three-state-access area, if the WAIT pin is low at the fall
of the system clock (ø) in the T2 state, a wait state (TW) is inserted. If the WAIT pin remains low,
wait states continue to be inserted until the WAIT signal goes high. Figure 6-5 shows the timing.
Inserted by WAIT signal
T1
ø
T2
TW
*
*
TW
T3
*
WAIT pin
Address bus
External address
AS
RD
Read
access
Read data
Data bus
WR
Write
access
Data bus
Write data
Note: * Arrows indicate time of sampling of the WAIT pin.
Figure 6-5 Pin Wait Mode 0
106
Pin Wait Mode 1: In all accesses to external three-state-access areas, the number of wait states
(TW) selected by bits WC1 and WC0 are inserted. If the WAIT pin is low at the fall of the system
clock (ø) in the last of these wait states, an additional wait state is inserted. If the WAIT pin
remains low, wait states continue to be inserted until the WAIT signal goes high.
Pin wait mode 1 is useful for inserting four or more wait states, or for inserting different numbers
of wait states for different external devices.
If the wait count is 0, this mode operates in the same way as pin wait mode 0.
Figure 6-6 shows the timing when the wait count is 1 (WC1 = 0, WC0 = 1) and one additional
wait state is inserted by WAIT input.
T1
Inserted by
wait count
Inserted by
WAIT signal
TW
TW
T2
ø
*
T3
*
WAIT pin
Address bus
External address
AS
Read
access
RD
Read data
Data bus
WR
Write
access
Data bus
Write data
Note: * Arrows indicate time of sampling of the WAIT pin.
Figure 6-6 Pin Wait Mode 1
107
Pin Auto-Wait Mode: If the WAIT pin is low, the number of wait states (TW) selected by bits
WC1 and WC0 are inserted.
In pin auto-wait mode, if the WAIT pin is low at the fall of the system clock (ø) in the T2 state, the
number of wait states (TW) selected by bits WC1 and WC0 are inserted. No additional wait states
are inserted even if the WAIT pin remains low.
Figure 6-7 shows the timing when the wait count is 1.
T1
ø
T2
T3
T1
T2
*
TW
T3
*
WAIT
Address bus
External address
External address
AS
RD
Read
access
Read data
Read data
Data bus
WR
Write
access
Data bus
Write data
Write data
Note: * Arrows indicate time of sampling of the WAIT pin.
Figure 6-7 Pin Auto-Wait Mode
108
Programmable Wait Mode: The number of wait states (TW) selected by bits WC1 and WC0 are
inserted in all accesses to external three-state-access areas. Figure 6-8 shows the timing when the
wait count is 1 (WC1 = 0, WC0 = 1).
T1
T2
TW
T3
ø
Address bus
External address
AS
RD
Read
access
Read data
Data bus
WR
Write
access
Write data
Data bus
Figure 6-8 Programmable Wait Mode
109
Example of Wait State Control Settings: A reset initializes ASTCR and WCER to H'FF and
WCR to H'F3, selecting programmable wait mode and three wait states for all areas. Software can
select other wait modes for individual areas by modifying the ASTCR, WCER, and WCR settings.
Figure 6-9 shows an example of wait mode settings.
Area 0
3-state-access area,
programmable wait mode
Area 1
3-state-access area,
programmable wait mode
Area 2
3-state-access area,
pin wait mode 0
Area 3
3-state-access area,
pin wait mode 0
Area 4
2-state-access area,
no wait states inserted
Area 5
2-state-access area,
no wait states inserted
Area 6
2-state-access area,
no wait states inserted
Area 7
2-state-access area,
no wait states inserted
Bit:
ASTCR H'0F:
7
0
6
0
5
0
4
0
3
1
2
1
1
1
0
1
WCER H'33:
0
0
1
1
0
0
1
1
WCR H'F3:
—
—
—
—
0
0
1
1
Note: Wait states cannot be inserted in areas designated for two-state access by ASTCR.
Figure 6-9 Wait Mode Settings (Example)
110
6.3.4 Interconnections with Memory (Example)
For each area, the bus controller can select two- or three-state access. In three-state-access areas,
wait states can be inserted in a variety of modes, simplifying the connection of both high-speed
and low-speed devices.
Figure 6-10 shows an example of the memory map.
A 16-kword ×8-bit EPROM is connected to area 0. This device is accessed in three states.
Two 32-kword ×8-bit SRAM devices (SRAM1 and SRAM2) are connected to area 1. These
devices are accessed in two states.
One 32-kword ×8-bit SRAM (SRAM3) is connected to area 7. This device is accessed via an
8-bit bus, using three-state access with an additional wait state inserted in pin auto-wait mode.
H'00000
EPROM
Area 0
Three-state-access area
H'03FFF
Not used
H'1FFFF
H'20000
SRAM1, 2
H'2FFFF
H'30000
Area 1
Two-state-access area
Not used
H'3FFFF
H'E0000
SRAM3
H'E7FFF
Area 7
8-bit, three-state-access area
(one auto-wait state)
Not used
On-chip RAM
H'FFFFF
On-chip I/O registers
Figure 6-10 Memory Map (Example)
111
6.4 Usage Notes
6.4.1 Register Write Timing
ASTCR and WCER Write Timing: Data written to ASTCR or WCER takes effect starting from
the next bus cycle. Figure 6-11 shows the timing when an instruction fetched from area 0 changes
area 0 from three-state access to two-state access.
T1
T2
T3
T1
T2
T3
T1
T2
ø
ASTCR address
Address
3-state access to area 0
2-state access
to area 0
Figure 6-11 ASTCR Write Timing
112
Section 7 I/O Ports
7.1 Overview
The H8/3004 and H8/3005 have five input/output ports (ports 6, 8, 9, A, and B) and one input port
(port 7). Table 7-1 summarizes the port functions. The pins in each port are multiplexed as shown in
table 7-1.
Ports 6 and 8 can drive one TTL load and a 90-pF capacitive load. Ports 9, A, and B can drive one
TTL load and a 30-pF capacitive load. Ports 6, 8, 9, A, and B can drive a darlington pair. Port B can
drive an LED (with 10-mA current sink). Pins P82 to P80, PA7 to PA0, and PB3 to PB0 have
Schmitt-trigger input circuits.
For block diagrams of the ports see appendix C, I/O Port Block Diagrams.
113
Table 7-1 Port Functions
Port
Description
Pins
Mode 1
Mode 3
Port 6
• 1-bit I/O port
P60/WAIT
Bus control signal input/output (WAIT) and
generic input/output
Port 7
• 8-bit input port
P77 to P70/
AN7 to AN0
Analog input (AN7 to AN0) to A/D converter, and
8-bit generic input
Port 8
• 4-bit I/O port
• P82 to P80 have
Schmitt inputs
P83/IRQ3
P82/IRQ2
P81/IRQ1
IRQ3 to IRQ1 input and generic input
DDR = 0 (after reset): generic input
DDR = 1: not used
P80/IRQ0
IRQ0 input and generic input/output
Port 9
• 3-bit I/O port
P94/SCK/IRQ4
P92/RxD
P90/TxD
Input and output (SCK, RxD, TxD) for serial
communication interface (SCI), IRQ4 input, and
3-bit generic input/output
Port A
• 8-bit I/O port
• Schmitt input
PA7/TIOCB2/A20
PA6/TIOCA2/A21
PA5/TIOCB1/A22
PA4/TIOCA1/A23
Input and output
(TIOCB2 to TIOCA1)
for 16-bit integrated
timer unit (ITU), and
generic input/output
Address output (A23 to
A20)
PA3/TIOCB0/TCLKD Input and output (TIOCB0, TIOCA0, TCLKA to
PA2/TIOCA0/TCLKC TCLKD) for ITU, and generic input/output
PA1/TCLKB
PA0/TCLKA
Port B • 8-bit I/O port
converter,
• Can drive LED
• PB3 to PB0 have
Schmitt inputs
PB7/ADTRG
External trigger input (ADTRG) to A/D
PB6
PB5/TOCXB4
PB4/TOCXA4
PB3/TIOCB4
PB2/TIOCA4
PB1/TIOCB3
PB0/TIOCA3
input and output (TOCXB4, TOCXA4, TIOCB4,
TIOCA4, TIOCB3, TIOCA3) for ITU, and 8-bit
generic input/output
114
7.2 Port 6
7.2.1 Overview
Port 6 is a 1-bit input/output port that is also used for input of a bus control signal (WAIT).
Figure 7-1 shows the pin configuration of port 6.
The port 6 pin can drive one TTL load and a 90-pF capacitive load. It can also drive a darlington
transistor pair.
Port 6 pins
Port 6
P60 (input/output)/WAIT (input)
Figure 7-1 Port 6 Pin Configuration
7.2.2 Register Descriptions
Table 7-2 summarizes the registers of port 6.
Table 7-2 Port 6 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFC9
Port 6 data direction register
P6DDR
W
H'80
H'FFCB
Port 6 data register
P6DR
R/W
H'80
Note: * Lower 16 bits of the address.
115
Port 6 Data Direction Register (P6DDR): P6DDR is an 8-bit write-only register that can select
input or output for the port 6 pin.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
P60DDR
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
W
W
W
W
W
W
W
Reserved bit
Port 6 data direction 0
This bit selects input or output for the port 6 pin
The port 6 pin becomes an output pin if the corresponding P6DDR bit is set to 1, and an input pin if
this bit is cleared to 0.
Bits 7 to 1 are reserved.
P6DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P6DDR is initialized to H'80 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting. If a P6DDR bit is set to 1, the corresponding pin maintains its output
state in software standby mode.
Port 6 Data Register (P6DR): P6DR is an 8-bit readable/writable register that stores data for pin
P60.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
P60
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bit
Port 6 data 0
This bit stores data for P60 pin
116
When a bit in P6DDR is set to 1, if port 6 is read the value of the corresponding P6DR bit is
returned directly. Bits 7 to 1 are reserved. Bit 7 cannot be modified and always reads 1. Bits 6, 2,
and 1 can be written and read, but cannot be used as ports. If bit 6, 2, or 1 in P6DDR is read while
its value is 1, the value of the corresponding bit in P6DR will be read. If bit 6, 2, or 1 in P6DDR is
read while its value is 0, it will always read 1.
Bits 5 to 3 can be written and read, but cannot be used as ports. If bit 5 to 3 in P6DDR is read while
its value is 1, the value of the corresponding bit in P6DR will be read. If bit 5 to 3 in P6DDR is read
while its value is 0, it will be undefined.
P6DR is initialized to H'80 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
7.2.3 Pin Functions
The port 6 pin also functions as the WAIT input pin. Table 7-3 shows the functions of the port 6
pin.
Table 7-3 Port 6 Pin Functions
Pin
Pin Functions and Selection Method
P60/WAIT
Bits WCE7 to WCE0 in WCER, bit WMS1 in WCR, and bit P60DDR select the
pin function as follows.
WCER
All 1s
WMS1
P60DDR
Pin function
Not all 1s
0
0
1
P60 input
P60 output
Note: * Do not set bit P60DDR to 1.
117
1
—
0*
0*
WAIT input
7.3 Port 7
7.3.1 Overview
Port 7 is an 8-bit input port that is also used for analog input to the A/D converter. The pin functions
are the same in all operating modes. Figure 7-2 shows the pin configuration of port 7.
Port 7 pins
P77 (input)/AN 7 (input)
P76 (input)/AN 6 (input)
P75 (input)/AN 5 (input)
Port 7
P74 (input)/AN 4 (input)
P73 (input)/AN 3 (input)
P72 (input)/AN 2 (input)
P71 (input)/AN 1 (input)
P70 (input)/AN 0 (input)
Figure 7-2 Port 7 Pin Configuration
118
7.3.2 Register Description
Table 7-4 summarizes the port 7 register. Port 7 is an input-only port, so it has no data direction
register.
Table 7-4 Port 7 Data Register
Address*
Name
Abbreviation
R/W
Initial Value
H'FFCE
Port 7 data register
P7DR
R
Undetermined
Note: * Lower 16 bits of the address.
Port 7 Data Register (P7DR)
Bit
7
6
5
4
3
2
1
0
P77
P76
P75
P74
P73
P72
P71
P70
Initial value
—*
—*
—*
—*
—*
—*
—*
—*
Read/Write
R
R
R
R
R
R
R
R
Note: * Determined by pins P7 7 to P70 .
When port 7 is read, the pin levels are always read.
119
7.4 Port 8
7.4.1 Overview
Port 8 is a 4-bit input/output port that is also used for IRQ3 to IRQ0 input. Port 8 pin functions are
the same in both operating modes. Figure 7-3 shows the pin configuration of port 8.
Pins in port 8 can drive one TTL load and a 90-pF capacitive load. They can also drive a darlington
transistor pair. Pins P82 to P80 have Schmitt-trigger inputs.
Port 8 pins
P83 (input)/IRQ3 (input)
Port 8
P82 (input)/IRQ2 (input)
P81 (input)/IRQ1 (input)
P80 (input/output)/IRQ0 (input)
Figure 7-3 Port 8 Pin Configuration
120
7.4.2 Register Descriptions
Table 7-5 summarizes the registers of port 8.
Table 7-5 Port 8 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFCD
Port 8 data direction
register
P8DDR
W
H'E0
H'FFCF
Port 8 data register
P8DR
R/W
H'E0
Note: * Lower 16 bits of the address.
Port 8 Data Direction Register (P8DDR): P8DDR is an 8-bit write-only register that can select
input or output for each pin in port 8.
7
6
5
4
Bit
—
—
—
—
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
W
W
W
W
W
Reserved bits
2
3
1
0
P8 3 DDR P8 2 DDR P8 1 DDR P8 0 DDR
Port 8 data direction 3 to 0
These bits select input or
output for port 8 pins
Pins P83 to P81 function as input pins. Do not set P83DDR to P81DDR to 1. Pin P80 functions as an
output pin when P80DDR is set to 1, and as input pin when P80DDR is cleared to 0.
Port 8 is a generic input/output port. A pin port 8 becomes an output pin if the corresponding
P8DDR bit is set to 1, and an input pin if this bit is cleared to 0.
P8DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P8DDR is initialized to H'E0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting. If a P8DDR bit is set to 1, the corresponding pin maintains its output
state in software standby mode.
121
Port 8 Data Register (P8DR): P8DR is an 8-bit readable/writable register that stores data for pins
P83 to P80.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
P8 3
P8 2
P8 1
P8 0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Reserved bits
Port 8 data 3 to 0
These bits store data
for port 8 pins
When a bit in P8DDR is set to 1, if port 8 is read the value of the corresponding P8DR bit is
returned directly. When a bit in P8DDR is cleared to 0, if port 8 is read the corresponding pin level
is read.
Bits 7 to 4 are reserved. Bits 7 to 5 cannot be modified and always read 1. Bit 4 can be written and
read, but it cannot be used for port input or output. If bit 4 of P8DDR is read while its value is 1, bit
4 of P8DR is read directly. If bit 4 of P8DDR is read while its value is 0, it always reads 1.
P8DR is initialized to H'E0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
122
7.4.3 Pin Functions
The port 8 pins are also used for IRQ3 to IRQ0. Table 7-6 describes the selection of pin functions.
Table 7-6 Port 8 Pin Functions
Pin
Pin Functions and Selection Method
P83/IRQ3
Bit P83DDR selects the pin function as follows
P83DDR
Pin function
0
1
P83 input
Illegal setting
IRQ3 input
P82/IRQ2
Bit P82DDR selects the pin function as follows
P82DDR
Pin function
0
1
P82 input
Illegal setting
IRQ2 input
P81/IRQ1
Bit P81DDR selects the pin function as follows
P81DDR
Pin function
0
1
P81 input
Illegal setting
IRQ1 input
P80/IRQ0
Bit P80DDR selects the pin function as follows
P80DDR
Pin function
0
1
P80 input
P80 output
IRQ0 input
123
7.5 Port 9
7.5.1 Overview
Port 9 is a 3-bit input/output port that is also used for input and output (TxD, RxD, SCK) by serial
communication interface (SCI), and for IRQ4 input. Port 9 has the same set of pin functions in all
operating modes. Figure 7-4 shows the pin configuration of port 9.
Pins in port 9 can drive one TTL load and a 30-pF capacitive load. They can also drive a darlington
transistor pair.
Port 9 pins
P94 (input/output)/SCK (input/output)/IRQ4 (input)
Port 9
P92 (input/output)/RxD (input)
P90 (input/output)/TxD (output)
Figure 7-4 Port 9 Pin Configuration
7.5.2 Register Descriptions
Table 7-7 summarizes the registers of port 9.
Table 7-7 Port 9 Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFD0
Port 9 data direction register
P9DDR
W
H'C0
H'FFD2
Port 9 data register
P9DR
R/W
H'C0
Note: * Lower 16 bits of the address.
124
Port 9 Data Direction Register (P9DDR): P9DDR is an 8-bit write-only register that can select
input or output for each pin in port 9.
Bit
7
6
5
4
3
2
1
0
—
—
—
P9 4 DDR
—
P9 2 DDR
—
P9 0 DDR
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
W
W
W
W
W
W
Reserved bits
Port 9 data direction 4, 2, 0
These bits select input or
output for port 9 pins
A pin in port 9 becomes an output pin if the corresponding P9DDR bit is set to 1, and an input pin
if this bit is cleared to 0.
P9DDR is a write-only register. Its value cannot be read. All bits return 1 when read.
P9DDR is initialized to H'C0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting. If a P9DDR bit is set to 1, the corresponding pin maintains its output
state in software standby mode.
Port 9 Data Register (P9DR): P9DR is an 8-bit readable/writable register that stores data for pins
P94, P92, and P90.
Bit
7
6
5
4
3
2
1
0
—
—
—
P9 4
—
P9 2
—
P9 0
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bits
Port 9 data 4, 2, 0
These bits store data
for port 9 pins
When a bit in P9DDR is set to 1, if port 9 is read the value of the corresponding P9DR bit is
returned directly. When a bit in P9DDR is cleared to 0, if port 9 is read the corresponding pin level
is read.
125
Bits 7 to 5, 3 and 1 are reserved. Bits 7 and 6 cannot be modified and always read 1. Bits 5, 3, and 1
can be written and read, but they cannot be used for port input or output. If bit 5, 3 or 1 in P9DDR
is read while its value is 1, the corresponding bit in P9DR is read directly. If bit 5, 3, or 1 in P9DDR
is read while its value is 0, it always read 1.
P9DR is initialized to H'C0 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
7.5.3 Pin Functions
The port 9 pins are also used for SCI input and output (TxD, RxD, SCK), and for IRQ4 input. Table
7-8 describes the selection of pin functions.
Table 7-8 Port 9 Pin Functions
Pin
Pin Functions and Selection Method
P94/SCK/IRQ4
Bit C/A in SMR of SCI, bits CKE0 and CKE1 in SCR of SCI, and bit P94DDR
select the pin function as follows
CKE1
0
C/A
0
CKE0
P94DDR
Pin function
1
0
0
1
P94
P94
input output
1
—
1
—
—
—
—
—
SCK output
SCK output
SCK input
IRQ4 input
P92/RxD
Bit RE in SCR of SCI and bit P92DDR select the pin function as follows
RE
P92DDR
Pin function
P90/TxD
0
1
0
1
—
P92 input
P92 output
RxD input
Bit TE in SCR of SCI and bit P90DDR select the pin function as follows
TE
P90DDR
Pin function
0
1
0
1
—
P90 input
P90 output
TxD output
126
7.6 Port A
7.6.1 Overview
Port A is an 8-bit input/output port that is also used for the address bus (A23 to A20) from input and
output (TIOCB2, TIOCA2, TIOCB1, TIOCA1, TIOCB0, TIOCA0, TCLKD, TCLKC, TCLKB,
TCLKA) by the 16-bit integrated timer unit (ITU), Figure 7-5 shows the pin configuration of port
A.
Pins in port A can drive one TTL load and a 30-pF capacitive load. They can also drive a darlington
transistor pair. Port A has Schmitt-trigger inputs.
Port A
Port A pins
Pin functions in mode 1
PA7/TIOCB2/A20
PA7 (input/output)/TIOCB2 (input/output)
PA6/TIOCA2/A21
PA6 (input/output)/TIOCA2 (input/output)
PA5/TIOCB1/A22
PA5 (input/output)/TIOCB1 (input/output)
PA4/TIOCA1/A23
PA4 (input/output)/TIOCA1 (input/output)
PA3/TIOCB0/TCLKD
PA3 (input/output)/TIOCB0 (input/output)/TCLKD (input)
PA2/TIOCA0/TCLKC
PA2 (input/output)/TIOCA0 (input/output)/TCLKC (input)
PA1/TCLKB
PA1 (input/output)/TCLKB (input)
PA0/TCLKA
PA0 (input/output)/TCLKA (input)
Pin functions in mode 3
A20 (output)
A21 (output)
A22 (output)
A23 (output)
Port A
PA3 (input/output)/TIOCB0 (input/output)/TCLKD (input)
PA2 (input/output)/TIOCA0 (input/output)/TCLKC (input)
PA1 (input/output)/TCLKB (input)
PA0 (input/output)TCLKA (input)
Figure 7-5 Port A Pin Configuration
127
7.6.2 Register Descriptions
Table 7-9 summarizes the registers of port A.
Table 7-9 Port A Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFD1
Port A data direction register
PADDR
W
H'00
H'FFD3
Port A data register
PADR
R/W
H'00
Note: * Lower 16 bits of the address.
Port A Data Direction Register (PADDR): PADDR is an 8-bit write-only register that can select
input or output for each pin in port A.
7
Bit
6
5
4
3
2
1
0
PA7 DDR PA6 DDR PA5 DDR PA4 DDR PA3 DDR PA2 DDR PA1 DDR PA0 DDR
Mode 1
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
W
W
W
W
W
W
W
Mode 3
Port A data direction 7 to 0
These bits select input or output for port A pins
A pin in port A becomes an output pin if the corresponding PADDR bit is set to 1, and an input pin
if this bit is cleared to 0.
PADDR is a write-only register. Its value cannot be read. All bits return 1 when read.
PADDR is initialized to H'00 in mode 1 or H'80 in mode 3 by a reset and in hardware standby
mode. In software standby mode it retains its previous setting. If a PADDR bit is set to 1, the
corresponding pin maintains its output state in software standby mode.
128
Port A Data Register (PADR): PADR is an 8-bit readable/writable register that stores data for pins
PA7 to PA0.
Bit
7
6
5
4
3
2
1
0
PA 7
PA 6
PA 5
PA 4
PA 3
PA 2
PA 1
PA 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port A data 7 to 0
These bits store data for port A pins
When a bit in PADDR is set to 1, if port A is read the value of the corresponding PADR bit is
returned directly. When a bit in PADDR is cleared to 0, if port A is read the corresponding pin level
is read.
PADR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
129
7.6.3 Pin Functions
The port A pins are also used for ITU input/output (TIOCB2 to TIOCB0, TIOCA2 to TIOCA0),
input (TCLKD, TCLKC, TCLKB, TCLKA), and the address bus (A23 to A20). Table 7-10 describes
the selection of pin functions.
Table 7-10 Port A Pin Functions
Pin
Pin Functions and Selection Method
PA7/TIOCB2/ Mode settings and ITU channel 2 settings (bit PWM2 in TMDR and bits IOB2 to IOB0
A20
in TIOR2) and bit PA7DDR in PADDR select the pin function as follows
Mode
ITU channel 2
settings
1
(1) in table below
PA7DDR
Pin function
3
(2) in table below
—
0
1
—
TIOCB2 output
PA7
input
PA7
output
A20
output
TIOCB2 input*
Note: * TIOCB2 input when IOB2 = 1 and PWM2 = 0.
ITU channel 2
settings
—
(2)
IOB2
(1)
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
130
Table 7-10 Port A Pin Functions (cont)
Pin
Pin Functions and Selection Method
PA6/TIOCA2/ Mode settings and ITU channel 2 settings (bit PWM2 in TMDR and bits IOA2 to IOA0
A21
in TIOR2) and bit PA6DDR in PADDR select the pin function as follows
Mode
1
ITU channel 2
settings
(1) in table below
PA6DDR
Pin function
3
(2) in table below
—
—
0
1
—
TIOCA2 output
PA6
input
PA6
output
A21
output
TIOCA2 input*
Note: * TIOCA2 input when IOA2 = 1.
ITU channel 2
settings
(2)
(1)
PWM2
(2)
0
IOA2
(1)
1
0
1
—
IOA1
0
0
1
—
—
IOA0
0
1
—
—
—
131
Table 7-10 Port A Pin Functions (cont)
Pin
Pin Functions and Selection Method
PA5/TIOCB1/ Mode settings and ITU channel 1 settings (bit PWM1 in TMDR and bits IOB2 to IOB0
A22
in TIOR1) and bit PA5DDR in PADDR select the pin function as follows
Mode
ITU channel 1
settings
1
(1) in table below
PA5DDR
Pin function
3
(2) in table below
—
0
1
—
TIOCB1 output
PA5
input
PA5
output
A22
output
TIOCB1 input*
Note: * TIOCB1 input when IOB2 = 1 and PWM1 = 0.
ITU channel 1
settings
—
(2)
IOB2
(1)
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
132
Table 7-10 Port A Pin Functions (cont)
Pin
Pin Functions and Selection Method
PA4/TIOCA1/ Mode settings and ITU channel 1 settings (bit PWM1 in TMDR and bits IOA2 to IOA0
A23
in TIOR1) and bit PA4DDR in PADDR select the pin function as follows
Mode
1
ITU channel 1
settings
(1) in table below
PA4DDR
Pin function
3
(2) in table below
—
—
0
1
—
TIOCA1 output
PA4
input
PA4
output
A23
output
TIOCA1 input*
Note: * TIOCA1 input when IOA2 = 1.
ITU channel 1
settings
(2)
(1)
PWM1
(2)
0
IOA2
(1)
1
0
1
—
IOA1
0
0
1
—
—
IOA0
0
1
—
—
—
133
Table 7-10 Port A Pin Functions (cont)
Pin
Pin Functions and Selection Method
PA3/TIOCB0/ ITU channel 0 settings (bit PWM0 in TMDR and bits IOB2 to IOB0 in TIOR0), bits
TCLKD
TPSC2 to TPSC0 in TCR4 to TCR0 and bit PA3DDR in PADDR select the pin
function as follows
ITU channel 0
settings
(1) in table below
PA3DDR
Pin function
(2) in table below
—
0
1
TIOCB0 output
PA3
input
PA3
output
TIOCB0 input*1
TCLKD
input*2
Notes: 1. TIOCB0 input when IOB2 = 1 and PWM0 = 0.
2. TCLKD input when TPSC2 = TPSC1 = TPSC0 = 1 in any of TCR4 to
TCR0.
ITU channel 0
settings
(2)
IOB2
(1)
(2)
0
1
IOB1
0
0
1
—
IOB0
0
1
—
—
134
Table 7-10 Port A Pin Functions (cont)
Pin
Pin Functions and Selection Method
PA2/TIOCA0/ ITU channel 0 settings (bit PWM0 in TMDR and bits IOA2 to IOA0 in TIOR0), bits
TCLKC
TPSC2 to TPSC0 in TCR4 to TCR0 and bit PA2DDR in PADDR select the pin
function as follows
ITU channel 0
settings
(1) in table below
PA2DDR
Pin function
(2) in table below
—
0
1
TIOCA0 output
PA2
input
PA2
output
TIOCA0 input*1
TCLKC
input*2
Notes: 1. TIOCA0 input when IOA2 = 1.
2. TCLKC input when TPSC2 = TPSC1 = 1 and TPSC0 = 0 in any of TCR4
to TCR0.
ITU channel 0
settings
(2)
(1)
PWM0
(2)
0
IOA2
(1)
1
0
1
—
IOA1
0
0
1
—
—
IOA0
0
1
—
—
—
135
Table 7-10 Port A Pin Functions (cont)
Pin
Pin Functions and Selection Method
PA1/TCLKB
Bit PA1DDR in PADDR select the pin function as follows
PA1DDR
Pin function
0
1
PA1 input
PA1 output
TCLKB input*
Note: * TCLKB input when MDF = 1 in TMDR, or when TPSC2 = 1, TPSC1 = 0, and
TPSC0 = 1 in any of TCR4 to TCR0.
PA0/TCLKA
Bit PA0DDR in PADDR select the pin function as follows
PA0DDR
Pin function
0
1
PA0 input
PA0 output
TCLKA input*
Note: * TCLKA input when MDF = 1 in TMDR, or when TPSC2 = 1, TPSC1 = 0 and
TPSC0 = 0 in any of TCR4 to TCR0.
136
7.7 Port B
7.7.1 Overview
Port B is an 8-bit input/output port that is also used for ITU input/output (TIOCB4, TIOCB3,
TIOCA4, TIOCA3) and ITU output (TOCXB4, TOCXA4), and ADTRG input to the A/D converter.
Port B has the same set of pin functions in all operating modes. Figure 7-6 shows the pin
configuration of port B.
Pins in port B can drive one TTL load and a 30-pF capacitive load. They can also drive a darlington
transistor pair. Pins PB3 to PB0 have Schmitt-trigger inputs.
Port B pins
PB 7 (input/output)/ADTRG (input)
PB 6 (input/output)
PB 5 (input/output)/TOCXB4 (output)
PB 4 (input/output)/TOCXA4 (output)
Port B
PB 3 (input/output)/TIOCB4 (input/output)
PB 2 (input/output)/TIOCA4 (input/output)
PB 1 (input/output)/TIOCB3 (input/output)
PB 0 (input/output)/TIOCA3 (input/output)
Figure 7-6 Port B Pin Configuration
7.7.2 Register Descriptions
Table 7-11 summarizes the registers of port B.
Table 7-11 Port B Registers
Address*
Name
Abbreviation
R/W
Initial Value
H'FFD4
Port B data direction register
PBDDR
W
H'00
H'FFD6
Port B data register
PBDR
R/W
H'00
Note: * Lower 16 bits of the address.
137
Port B Data Direction Register (PBDDR): PBDDR is an 8-bit write-only register that can select
input or output for each pin in port B.
Bit
7
6
5
4
3
2
1
0
PB7 DDR PB6 DDR PB5 DDR PB4 DDR PB3 DDR PB2 DDR PB1 DDR PB0 DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port B data direction 7 to 0
These bits select input or output for port B pins
A pin in port B becomes an output pin if the corresponding PBDDR bit is set to 1, and an input pin
if this bit is cleared to 0.
PBDDR is a write-only register. Its value cannot be read. All bits return 1 when read.
PBDDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting. If a PBDDR bit is set to 1, the corresponding pin maintains its output
state in software standby mode.
Port B Data Register (PBDR): PBDR is an 8-bit readable/writable register that stores data for pins
PB7 to PB0.
Bit
7
6
5
4
3
2
1
0
PB 7
PB 6
PB 5
PB 4
PB 3
PB 2
PB 1
PB 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Port B data 7 to 0
These bits store data for port B pins
When a bit in PBDDR is set to 1, if port B is read the value of the corresponding PBDR bit is
returned directly. When a bit in PBDDR is cleared to 0, if port B is read the corresponding pin level
is read.
PBDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it
retains its previous setting.
138
7.7.3 Pin Functions
The port B pins are also used for ITU input/output (TIOCB4, TIOCB3, TIOCA4, TIOCA3) and
output (TOCXB4, TOCXA4), and ADTRG input. Table 7-12 describes the selection of pin
functions.
Table 7-12 Port B Pin Functions
Pin
Pin Functions and Selection Method
PB7/
ADTRG
Bit TRGE in ADCR and bit PB7DDR in PBDDR select the pin function as follows
PB7DDR
Pin function
0
1
PB7 input
PB7 output
ADTRG input*
Note: * ADTRG input when TRGE = 1.
PB6
Bit PB6DDR in PBDDR select the pin function as follows
PB6DDR
Pin function
PB5/
TOCXB4
1
PB6 input
PB6 output
ITU channel 4 settings (bit CMD1 in TFCR and bit EXB4 in TOER) and bit PB5DDR in
PBDDR select the pin function as follows
EXB4, CMD1
PB5DDR
Pin function
PB4/
TOCXA4
0
Not both 1
Both 1
0
1
—
PB5 input
PB5 output
TOCXB4 output
ITU channel 4 settings (bit CMD1 in TFCR and bit EXA4 in TOER) and bit PB4DDR
in PBDDR select the pin function as follows
EXA4, CMD1
PB4DDR
Pin function
Not both 1
Both 1
0
1
—
PB4 input
PB4 output
TOCXA4 output
139
Table 7-12 Port B Pin Functions (cont)
Pin
Pin Functions and Selection Method
PB3/TIOCB4
ITU channel 4 settings (bit PWM4 in TMDR, bit CMD1 in TFCR, bit EB4 in TOER,
and bits IOB2 to IOB0 in TIOR4) and bit PB3DDR in PBDDR select the pin function
as follows
ITU channel 4
settings
(1) in table below
PB3DDR
Pin function
(2) in table below
—
0
1
TIOCB4 output
PB3 input
PB3 output
TIOCB4 input*
Note: * TIOCB4 input when CMD1 = PWM4 = 0 and IOB2 = 1.
ITU channel 4
settings
(2)
(2)
(1)
(2)
(1)
EB4
0
1
CMD1
—
IOB2
—
0
0
0
1
—
IOB1
—
0
0
1
—
—
IOB0
—
0
1
—
—
—
0
140
1
Table 7-12 Port B Pin Functions (cont)
Pin
Pin Functions and Selection Method
PB2/TIOCA4
ITU channel 4 settings (bit CMD1 in TFCR, bit EA4 in TOER, bit PWM4 in TMDR,
and bits IOA2 to IOA0 in TIOR4) and bit PB2DDR in PBDDR select the pin function
as follows
ITU channel 4
settings
(1) in table below
PB2DDR
Pin function
(2) in table below
—
0
1
TIOCA4 output
PB2 input
PB2 output
TIOCA4 input*
Note: * TIOCA4 input when CMD1 = PWM4 = 0 and IOA2 = 1.
DMAC
channel 4
settings
(2)
(2)
(1)
(2)
EA4
0
CMD1
—
PWM4
—
IOA2
—
0
0
0
IOA1
—
0
0
IOA0
—
0
1
(1)
1
0
1
0
141
1
—
1
—
—
1
—
—
—
—
—
—
—
Table 7-12 Port B Pin Functions (cont)
Pin
Pin Functions and Selection Method
PB1/TIOCB3
ITU channel 3 settings (bit PWM3 in TMDR, bit CMD1 in TFCR, bit EB3 in TOER,
and bits IOB2 to IOB0 in TIOR3) and bit PB1DDR in PBDDR select the pin function
as follows
ITU channel 3
settings
(1) in table below
PB1DDR
Pin function
(2) in table below
—
0
1
TIOCB3 output
PB1 input
PB1 output
TIOCB3 input*
Note: * TIOCB3 input when CMD1 = PWM3 = 0 and IOB2 = 1.
ITU channel 3
settings
(2)
(2)
(1)
(2)
(1)
EB3
0
1
CMD1
—
IOB2
—
0
0
0
1
—
IOB1
—
0
0
1
—
—
IOB0
—
0
1
—
—
—
0
142
1
Table 7-12 Port B Pin Functions (cont)
Pin
Pin Functions and Selection Method
PB0/TIOCA3
ITU channel 3 settings (bit CMD1 in TFCR, bit EA3 in TOER, bit PWM3 in TMDR,
and bits IOA2 to IOA0 in TIOR3) and bit PB0DDR in PBDDR select the pin function
as follows
ITU channel 3
settings
(1) in table below
PB0DDR
Pin function
(2) in table below
—
0
1
TIOCA3 output
PB0 input
PB0 output
TIOCA3 input*
Note: * TIOCA3 input when CMD1 = PWM3 = 0 and IOA2 = 1.
ITU channel 3
settings
(2)
(2)
(1)
(2)
EA3
0
CMD1
—
PWM3
—
IOA2
—
0
0
0
IOA1
—
0
0
IOA0
—
0
1
(1)
1
0
1
0
143
1
—
1
—
—
1
—
—
—
—
—
—
—
144
Section 8 16-Bit Integrated Timer Unit (ITU)
8.1 Overview
The H8/3004 and H8/3005 have a built-in 16-bit integrated timer-pulse unit (ITU) with five 16-bit
timer channels.
8.1.1 Features
ITU features are listed below.
•
Capability to process up to 12 pulse outputs or 10 pulse inputs
•
Ten general registers (GRs, two per channel) with independently-assignable output compare
or input capture functions
•
Selection of eight counter clock sources for each channel:
Internal clocks: ø, ø/2, ø/4, ø/8
External clocks: TCLKA, TCLKB, TCLKC, TCLKD
•
Five operating modes selectable in all channels:
— Waveform output by compare match
Selection of 0 output, 1 output, or toggle output (only 0 or 1 output in channel 2)
— Input capture function
Rising edge, falling edge, or both edges (selectable)
— Counter clearing function
Counters can be cleared by compare match or input capture
— Synchronization
Two or more timer counters (TCNTs) can be preset simultaneously, or cleared
simultaneously by compare match or input capture. Counter synchronization enables
synchronous register input and output.
145
— PWM mode
PWM output can be provided with an arbitrary duty cycle. With synchronization, up to
five-phase PWM output is possible
•
Phase counting mode selectable in channel 2
Two-phase encoder output can be counted automatically.
•
Three additional modes selectable in channels 3 and 4
— Reset-synchronized PWM mode
If channels 3 and 4 are combined, three-phase PWM output is possible with three pairs of
complementary waveforms.
— Complementary PWM mode
If channels 3 and 4 are combined, three-phase PWM output is possible with three pairs of
non-overlapping complementary waveforms.
— Buffering
Input capture registers can be double-buffered. Output compare registers can be updated
automatically.
•
High-speed access via internal 16-bit bus
The 16-bit timer counters, general registers, and buffer registers can be accessed at high speed
via a 16-bit bus.
•
Fifteen interrupt sources
Each channel has two compare match/input capture interrupts and an overflow interrupt. All
interrupts can be requested independently.
146
Table 8-1 summarizes the ITU functions.
Table 8-1 ITU Functions
Item
Channel 0
Channel 1
Channel 2
Channel 3
Channel 4
Clock sources
Internal clocks: ø, ø/2, ø/4, ø/8
External clocks: TCLKA, TCLKB, TCLKC, TCLKD, selectable independently
General registers
(output compare/input
capture registers)
GRA0, GRB0
GRA1, GRB1
GRA2, GRB2
GRA3, GRB3
Buffer registers
—
—
—
BRA3, BRB3
BRA4, BRB4
Input/output pins
TIOCA0,
TIOCB0
TIOCA1,
TIOCB1
TIOCA2,
TIOCB2
TIOCA3,
TIOCB3
TIOCA4,
TIOCB4
Output pins
—
—
—
—
TOCXA4,
TOCXB4
Counter clearing function
GRA0/GRB0
compare
match or
input capture
GRA1/GRB1
compare
match or
input capture
GRA2/GRB2
compare
match or
input capture
GRA3/GRB3
compare
match or
input capture
GRA4/GRB4
compare
match or
input capture
Compare
match output
0
o
o
o
o
o
1
o
o
o
o
o
Toggle
GRA4, GRB4
o
o
—
o
o
Input capture function
o
o
o
o
o
Synchronization
o
o
o
o
o
PWM mode
o
o
o
o
o
Reset-synchronized
PWM mode
—
—
—
o
o
Complementary PWM
mode
—
—
—
o
o
Phase counting mode
—
—
o
—
—
Buffering
—
—
—
o
o
Interrupt sources
Three sources
Three sources
Three sources
Three sources
Three sources
• Compare
match/input
capture A0
• Compare
match/input
capture A1
• Compare
match/input
capture A2
• Compare
match/input
capture A3
• Compare
match/input
capture A4
• Compare
match/input
capture B0
• Compare
match/input
capture B1
• Compare
match/input
capture B2
• Compare
match/input
capture B3
• Compare
match/input
capture B4
• Overflow
• Overflow
• Overflow
• Overflow
• Overflow
Legend
o: Available
—: Not available
147
8.1.2 Block Diagrams
ITU Block Diagram (overall): Figure 8-1 is a block diagram of the ITU.
TCLKA to TCLKD
IMIA0 to IMIA4
IMIB0 to IMIB4
OVI0 to OVI4
Clock selector
ø, ø/2, ø/4, ø/8
TOCXA4, TOCXB4
Control logic
TIOCA0 to TIOCA4
TIOCB0 to TIOCB4
TSTR
TSNC
TMDR
TFCR
Module data bus
Legend
TOER:
TOCR:
TSTR:
TSNC:
TMDR:
TFCR:
Timer output master enable register (8 bits)
Timer output control register (8 bits)
Timer start register (8 bits)
Timer synchro register (8 bits)
Timer mode register (8 bits)
Timer function control register (8 bits)
Figure 8-1 ITU Block Diagram (Overall)
148
On-chip data bus
TOCR
Bus interface
16-bit timer channel 0
16-bit timer channel 1
16-bit timer channel 2
16-bit timer channel 3
16-bit timer channel 4
TOER
Block Diagram of Channels 0 and 1: ITU channels 0 and 1 are functionally identical. Both have
the structure shown in figure 8-2.
TCLKA to TCLKD
TIOCA0
TIOCB0
Clock selector
ø, ø/2, ø/4, ø/8
Control logic
IMIA0
IMIB0
OVI0
TSR
TIER
TIOR
TCR
GRB
GRA
TCNT
Comparator
Module data bus
Legend
TCNT:
GRA, GRB:
TCR:
TIOR:
TIER:
TSR:
Timer counter (16 bits)
General registers A and B (input capture/output compare registers) (16 bits × 2)
Timer control register (8 bits)
Timer I/O control register (8 bits)
Timer interrupt enable register (8 bits)
Timer status register (8 bits)
Figure 8-2 Block Diagram of Channels 0 and 1 (for Channel 0)
149
Block Diagram of Channel 2: Figure 8-3 is a block diagram of channel 2. This is the channel
that provides only 0 output and 1 output.
TCLKA to TCLKD
TIOCA2
TIOCB2
Clock selector
ø, ø/2, ø/4, ø/8
Control logic
IMIA2
IMIB2
OVI2
TSR2
TIER2
TIOR2
TCR2
GRB2
GRA2
TCNT2
Comparator
Module data bus
Legend
Timer counter 2 (16 bits)
TCNT2:
GRA2, GRB2: General registers A2 and B2 (input capture/output compare registers)
(16 bits × 2)
Timer control register 2 (8 bits)
TCR2:
Timer I/O control register 2 (8 bits)
TIOR2:
Timer interrupt enable register 2 (8 bits)
TIER2:
Timer status register 2 (8 bits)
TSR2:
Figure 8-3 Block Diagram of Channel 2
150
Block Diagrams of Channels 3 and 4: Figure 8-4 is a block diagram of channel 3. Figure 8-5 is a
block diagram of channel 4.
TCLKA to
TCLKD
ø, ø/2,
ø/4, ø/8
TIOCA3
TIOCB3
Clock selector
Control logic
IMIA3
IMIB3
OVI3
TSR3
TIER3
TIOR3
TCR3
GRB3
BRB3
GRA3
BRA3
TCNT3
Comparator
Module data bus
Legend
Timer counter 3 (16 bits)
TCNT3:
GRA3, GRB3: General registers A3 and B3 (input capture/output compare registers)
(16 bits × 2)
BRA3, BRB3: Buffer registers A3 and B3 (input capture/output compare buffer registers)
(16 bits × 2)
Timer control register 3 (8 bits)
TCR3:
Timer I/O control register 3 (8 bits)
TIOR3:
Timer interrupt enable register 3 (8 bits)
TIER3:
Timer status register 3 (8 bits)
TSR3:
Figure 8-4 Block Diagram of Channel 3
151
TCLKA to
TCLKD
ø, ø/2,
ø/4, ø/8
TOCXA4
TOCXB4
TIOCA4
TIOCB4
IMIA4
IMIB4
OVI4
Clock selector
Control logic
TSR4
TIER4
TIOR4
TCR4
GRB4
BRB4
GRA4
BRA4
TCNT4
Comparator
Module data bus
Legend
Timer counter 4 (16 bits)
TCNT4:
GRA4, GRB4: General registers A4 and B4 (input capture/output compare registers)
(16 bits × 2)
BRA4, BRB4: Buffer registers A4 and B4 (input capture/output compare buffer registers)
(16 bits × 2)
Timer control register 4 (8 bits)
TCR4:
Timer I/O control register 4 (8 bits)
TIOR4:
Timer interrupt enable register 4 (8 bits)
TIER4:
Timer status register 4 (8 bits)
TSR4:
Figure 8-5 Block Diagram of Channel 4
152
8.1.3 Input/Output Pins
Table 8-2 summarizes the ITU pins.
Table 8-2 ITU Pins
Abbreviation
Input/
Output
Common Clock input A
TCLKA
Input
External clock A input pin
(phase-A input pin in phase counting mode)
Clock input B
TCLKB
Input
External clock B input pin
(phase-B input pin in phase counting mode)
Clock input C
TCLKC
Input
External clock C input pin
Clock input D
TCLKD
Input
External clock D input pin
Input capture/output
compare A0
TIOCA0
Input/
output
GRA0 output compare or input capture pin
PWM output pin in PWM mode
Input capture/output
compare B0
TIOCB0
Input/
output
GRB0 output compare or input capture pin
Input capture/output
compare A1
TIOCA1
Input/
output
GRA1 output compare or input capture pin
PWM output pin in PWM mode
Input capture/output
compare B1
TIOCB1
Input/
output
GRB1 output compare or input capture pin
Input capture/output
compare A2
TIOCA2
Input/
output
GRA2 output compare or input capture pin
PWM output pin in PWM mode
Input capture/output
compare B2
TIOCB2
Input/
output
GRB2 output compare or input capture pin
Input capture/output
compare A3
TIOCA3
Input/
output
GRA3 output compare or input capture pin
PWM output pin in PWM mode, complementary PWM mode, or reset-synchronized
PWM mode
Input capture/output
compare B3
TIOCB3
Input/
output
GRB3 output compare or input capture pin
PWM output pin in complementary PWM
mode or reset-synchronized PWM mode
Input capture/output
compare A4
TIOCA4
Input/
output
GRA4 output compare or input capture pin
PWM output pin in PWM mode, complementary PWM mode, or reset-synchronized
PWM mode
Input capture/output
compare B4
TIOCB4
Input/
output
GRB4 output compare or input capture pin
PWM output pin in complementary PWM
mode or reset-synchronized PWM mode
Output compare XA4 TOCXA4
Output
PWM output pin in complementary PWM
mode or reset-synchronized PWM mode
Output compare XB4 TOCXB4
Output
PWM output pin in complementary PWM
mode or reset-synchronized PWM mode
Channel
0
1
2
3
4
Name
153
Function
8.1.4 Register Configuration
Table 8-3 summarizes the ITU registers.
Table 8-3 ITU Registers
Channel
Address*1
Name
Abbreviation
R/W
Initial
Value
Common
H'FF60
Timer start register
TSTR
R/W
H'E0
H'FF61
Timer synchro register
TSNC
R/W
H'E0
H'FF62
Timer mode register
TMDR
R/W
H'80
H'FF63
Timer function control register
TFCR
R/W
H'C0
H'FF90
Timer output master enable register
TOER
R/W
H'FF
H'FF91
Timer output control register
TOCR
R/W
H'FF
H'FF64
Timer control register 0
TCR0
R/W
H'80
H'FF65
Timer I/O control register 0
TIOR0
R/W
H'88
H'FF66
Timer interrupt enable register 0
TIER0
R/W
H'F8
H'FF67
Timer status register 0
TSR0
R/(W)*2
H'F8
H'FF68
Timer counter 0 (high)
TCNT0H
R/W
H'00
H'FF69
Timer counter 0 (low)
TCNT0L
R/W
H'00
H'FF6A
General register A0 (high)
GRA0H
R/W
H'FF
H'FF6B
General register A0 (low)
GRA0L
R/W
H'FF
H'FF6C
General register B0 (high)
GRB0H
R/W
H'FF
H'FF6D
General register B0 (low)
GRB0L
R/W
H'FF
H'FF6E
Timer control register 1
TCR1
R/W
H'80
H'FF6F
Timer I/O control register 1
TIOR1
R/W
H'88
H'FF70
Timer interrupt enable register 1
TIER1
R/W
H'F8
H'FF71
Timer status register 1
TSR1
R/(W)*2
H'F8
H'FF72
Timer counter 1 (high)
TCNT1H
R/W
H'00
H'FF73
Timer counter 1 (low)
TCNT1L
R/W
H'00
H'FF74
General register A1 (high)
GRA1H
R/W
H'FF
H'FF75
General register A1 (low)
GRA1L
R/W
H'FF
H'FF76
General register B1 (high)
GRB1H
R/W
H'FF
H'FF77
General register B1 (low)
GRB1L
R/W
H'FF
0
1
Notes: 1. The lower 16 bits of the address are indicated.
2. Only 0 can be written, to clear flags.
154
Table 8-3 ITU Registers (cont)
Channel
Address*1
Name
Abbreviation
R/W
Initial
Value
2
H'FF78
Timer control register 2
TCR2
R/W
H'80
H'FF79
Timer I/O control register 2
TIOR2
R/W
H'88
H'FF7A
Timer interrupt enable register 2
TIER2
R/W
H'F8
H'F8
3
H'FF7B
Timer status register 2
TSR2
R/(W)*2
H'FF7C
Timer counter 2 (high)
TCNT2H
R/W
H'00
H'FF7D
Timer counter 2 (low)
TCNT2L
R/W
H'00
H'FF7E
General register A2 (high)
GRA2H
R/W
H'FF
H'FF7F
General register A2 (low)
GRA2L
R/W
H'FF
H'FF80
General register B2 (high)
GRB2H
R/W
H'FF
H'FF81
General register B2 (low)
GRB2L
R/W
H'FF
H'FF82
Timer control register 3
TCR3
R/W
H'80
H'FF83
Timer I/O control register 3
TIOR3
R/W
H'88
H'FF84
Timer interrupt enable register 3
TIER3
R/W
H'F8
H'F8
H'FF85
Timer status register 3
TSR3
R/(W)*2
H'FF86
Timer counter 3 (high)
TCNT3H
R/W
H'00
H'FF87
Timer counter 3 (low)
TCNT3L
R/W
H'00
H'FF88
General register A3 (high)
GRA3H
R/W
H'FF
H'FF89
General register A3 (low)
GRA3L
R/W
H'FF
H'FF8A
General register B3 (high)
GRB3H
R/W
H'FF
H'FF8B
General register B3 (low)
GRB3L
R/W
H'FF
H'FF8C
Buffer register A3 (high)
BRA3H
R/W
H'FF
H'FF8D
Buffer register A3 (low)
BRA3L
R/W
H'FF
H'FF8E
Buffer register B3 (high)
BRB3H
R/W
H'FF
H'FF8F
Buffer register B3 (low)
BRB3L
R/W
H'FF
Notes: 1. The lower 16 bits of the address are indicated.
2. Only 0 can be written, to clear flags.
155
Table 8-3 ITU Registers (cont)
Channel
Address*1
Name
Abbreviation
R/W
Initial
Value
4
H'FF92
Timer control register 4
TCR4
R/W
H'80
H'FF93
Timer I/O control register 4
TIOR4
R/W
H'88
H'FF94
Timer interrupt enable register 4
TIER4
R/W
H'F8
H'F8
H'FF95
Timer status register 4
TSR4
R/(W)*2
H'FF96
Timer counter 4 (high)
TCNT4H
R/W
H'00
H'FF97
Timer counter 4 (low)
TCNT4L
R/W
H'00
H'FF98
General register A4 (high)
GRA4H
R/W
H'FF
H'FF99
General register A4 (low)
GRA4L
R/W
H'FF
H'FF9A
General register B4 (high)
GRB4H
R/W
H'FF
H'FF9B
General register B4 (low)
GRB4L
R/W
H'FF
H'FF9C
Buffer register A4 (high)
BRA4H
R/W
H'FF
H'FF9D
Buffer register A4 (low)
BRA4L
R/W
H'FF
H'FF9E
Buffer register B4 (high)
BRB4H
R/W
H'FF
H'FF9F
Buffer register B4 (low)
BRB4L
R/W
H'FF
Notes: 1. The lower 16 bits of the address are indicated.
2. Only 0 can be written, to clear flags.
156
8.2 Register Descriptions
8.2.1 Timer Start Register (TSTR)
TSTR is an 8-bit readable/writable register that starts and stops the timer counter (TCNT) in
channels 0 to 4.
Bit
7
6
5
4
3
2
1
0
—
—
—
STR4
STR3
STR2
STR1
STR0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Reserved bits
Counter start 4 to 0
These bits start and
stop TCNT4 to TCNT0
TSTR is initialized to H'E0 by a reset and in standby mode.
Bits 7 to 5—Reserved: Read-only bits, always read as 1.
Bit 4—Counter Start 4 (STR4): Starts and stops timer counter 4 (TCNT4).
Bit 4
STR4
Description
0
TCNT4 is halted
1
TCNT4 is counting
(Initial value)
Bit 3—Counter Start 3 (STR3): Starts and stops timer counter 3 (TCNT3).
Bit 3
STR3
Description
0
TCNT3 is halted
1
TCNT3 is counting
(Initial value)
Bit 2—Counter Start 2 (STR2): Starts and stops timer counter 2 (TCNT2).
Bit 2
STR2
Description
0
TCNT2 is halted
1
TCNT2 is counting
(Initial value)
157
Bit 1—Counter Start 1 (STR1): Starts and stops timer counter 1 (TCNT1).
Bit 1
STR1
Description
0
TCNT1 is halted
1
TCNT1 is counting
(Initial value)
Bit 0—Counter Start 0 (STR0): Starts and stops timer counter 0 (TCNT0).
Bit 0
STR0
Description
0
TCNT0 is halted
1
TCNT0 is counting
(Initial value)
8.2.2 Timer Synchro Register (TSNC)
TSNC is an 8-bit readable/writable register that selects whether channels 0 to 4 operate
Bit
7
6
5
4
3
2
1
0
—
—
—
SYNC4
SYNC3
SYNC2
SYNC1
SYNC0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Reserved bits
Timer sync 4 to 0
These bits synchronize
channels 4 to 0
independently or synchronously. Channels are synchronized by setting the corresponding bits to 1.
TSNC is initialized to H'E0 by a reset and in standby mode.
Bits 7 to 5—Reserved: Read-only bits, always read as 1.
Bit 4—Timer Sync 4 (SYNC4): Selects whether channel 4 operates independently or
synchronously.
Bit 4
SYNC4
0
Description
Channel 4’s timer counter (TCNT4) operates independently
TCNT4 is preset and cleared independently of other channels
158
(Initial value)
1
Channel 4 operates synchronously
TCNT4 can be synchronously preset and cleared
Bit 3—Timer Sync 3 (SYNC3): Selects whether channel 3 operates independently or
synchronously.
Bit 3
SYNC3
Description
0
Channel 3’s timer counter (TCNT3) operates independently
TCNT3 is preset and cleared independently of other channels
1
Channel 3 operates synchronously
TCNT3 can be synchronously preset and cleared
(Initial value)
Bit 2—Timer Sync 2 (SYNC2): Selects whether channel 2 operates independently or
synchronously.
Bit 2
SYNC2
Description
0
Channel 2’s timer counter (TCNT2) operates independently
TCNT2 is preset and cleared independently of other channels
1
Channel 2 operates synchronously
TCNT2 can be synchronously preset and cleared
(Initial value)
Bit 1—Timer Sync 1 (SYNC1): Selects whether channel 1 operates independently or
synchronously.
Bit 1
SYNC1
Description
0
Channel 1’s timer counter (TCNT1) operates independently
TCNT1 is preset and cleared independently of other channels
1
Channel 1 operates synchronously
TCNT1 can be synchronously preset and cleared
(Initial value)
Bit 0—Timer Sync 0 (SYNC0): Selects whether channel 0 operates independently or
synchronously.
Bit 0
SYNC0
Description
0
Channel 0’s timer counter (TCNT0) operates independently
TCNT0 is preset and cleared independently of other channels
1
Channel 0 operates synchronously
TCNT0 can be synchronously preset and cleared
159
(Initial value)
8.2.3 Timer Mode Register (TMDR)
TMDR is an 8-bit readable/writable register that selects PWM mode for channels 0 to 4. It also
Bit
7
6
5
4
3
2
1
0
—
MDF
FDIR
PWM4
PWM3
PWM2
PWM1
PWM0
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
PWM mode 4 to 0
These bits select PWM
mode for channels 4 to 0
Flag direction
Selects the setting condition for the overflow
flag (OVF) in timer status register 2 (TSR2)
Phase counting mode flag
Selects phase counting mode for channel 2
Reserved bit
selects phase counting mode and the overflow flag (OVF) setting conditions for channel 2.
TMDR is initialized to H'80 by a reset and in standby mode.
Bit 7—Reserved: Read-only bit, always read as 1.
Bit 6—Phase Counting Mode Flag (MDF): Selects whether channel 2 operates normally or in
phase counting mode.
Bit 6
MDF
Description
0
Channel 2 operates normally
1
Channel 2 operates in phase counting mode
(Initial value)
160
When MDF is set to 1 to select phase counting mode, timer counter 2 (TCNT2) operates as an
up/down-counter and pins TCLKA and TCLKB become counter clock input pins. TCNT2 counts
both rising and falling edges of TCLKA and TCLKB, and counts up or down as follows.
Counting Direction
Down-Counting
TCLKA pin
TCLKB pin
Up-Counting
High
Low
Low
High
Low
High
High
Low
In phase counting mode channel 2 operates as above regardless of the external clock edges
selected by bits CKEG1 and CKEG0 and the clock source selected by bits TPSC2 to TPSC0 in
timer control register 2 (TCR2). Phase counting mode takes precedence over these settings.
The counter clearing condition selected by the CCLR1 and CCLR0 bits in TCR2 and the compare
match/input capture settings and interrupt functions of timer I/O control register 2 (TIOR2), timer
interrupt enable register 2 (TIER2), and timer status register 2 (TSR2) remain effective in phase
counting mode.
Bit 5—Flag Direction (FDIR): Designates the setting condition for the overflow flag (OVF) in
timer status register 2 (TSR2). The FDIR designation is valid in all modes in channel 2.
Bit 5
FDIR
Description
0
OVF is set to 1 in TSR2 when TCNT2 overflows or underflows
1
OVF is set to 1 in TSR2 when TCNT2 overflows
(Initial value)
Bit 4—PWM Mode 4 (PWM4): Selects whether channel 4 operates normally or in PWM mode.
Bit 4
PWM4
Description
0
Channel 4 operates normally
1
Channel 4 operates in PWM mode
(Initial value)
When bit PWM4 is set to 1 to select PWM mode, pin TIOCA4 becomes a PWM output pin. The
output goes to 1 at compare match with general register A4 (GRA4), and to 0 at compare match
with general register B4 (GRB4).
If complementary PWM mode or reset-synchronized PWM mode is selected by bits CMD1 and
CMD0 in the timer function control register (TFCR), the CMD1 and CMD0 setting takes
precedence and the PWM4 setting is ignored.
161
Bit 3—PWM Mode 3 (PWM3): Selects whether channel 3 operates normally or in PWM mode.
Bit 3
PWM3
Description
0
Channel 3 operates normally
1
Channel 3 operates in PWM mode
(Initial value)
When bit PWM3 is set to 1 to select PWM mode, pin TIOCA3 becomes a PWM output pin. The
output goes to 1 at compare match with general register A3 (GRA3), and to 0 at compare match
with general register B3 (GRB3).
If complementary PWM mode or reset-synchronized PWM mode is selected by bits CMD1 and
CMD0 in the timer function control register (TFCR), the CMD1 and CMD0 setting takes
precedence and the PWM3 setting is ignored.
Bit 2—PWM Mode 2 (PWM2): Selects whether channel 2 operates normally or in PWM mode.
Bit 2
PWM2
Description
0
Channel 2 operates normally
1
Channel 2 operates in PWM mode
(Initial value)
When bit PWM2 is set to 1 to select PWM mode, pin TIOCA2 becomes a PWM output pin. The
output goes to 1 at compare match with general register A2 (GRA2), and to 0 at compare match
with general register B2 (GRB2).
Bit 1—PWM Mode 1 (PWM1): Selects whether channel 1 operates normally or in PWM mode.
Bit 1
PWM1
Description
0
Channel 1 operates normally
1
Channel 1 operates in PWM mode
(Initial value)
When bit PWM1 is set to 1 to select PWM mode, pin TIOCA1 becomes a PWM output pin. The
output goes to 1 at compare match with general register A1 (GRA1), and to 0 at compare match
with general register B1 (GRB1).
162
Bit 0—PWM Mode 0 (PWM0): Selects whether channel 0 operates normally or in PWM mode.
Bit 0
PWM0
Description
0
Channel 0 operates normally
1
Channel 0 operates in PWM mode
(Initial value)
When bit PWM0 is set to 1 to select PWM mode, pin TIOCA0 becomes a PWM output pin. The
output goes to 1 at compare match with general register A0 (GRA0), and to 0 at compare match
with general register B0 (GRB0).
8.2.4 Timer Function Control Register (TFCR)
TFCR is an 8-bit readable/writable register that selects complementary PWM mode, resetsynchronized PWM mode, and buffering for channels 3 and 4.
Bit
7
6
5
4
3
2
1
0
—
—
CMD1
CMD0
BFB4
BFA4
BFB3
BFA3
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bits
Combination mode 1/0
These bits select complementary
PWM mode or reset-synchronized
PWM mode for channels 3 and 4
Buffer mode B4 and A4
These bits select buffering of
general registers (GRB4 and
GRA4) by buffer registers
(BRB4 and BRA4) in channel 4
Buffer mode B3 and A3
These bits select buffering
of general registers (GRB3
and GRA3) by buffer
registers (BRB3 and BRA3)
in channel 3
TFCR is initialized to H'C0 by a reset and in standby mode.
Bits 7 and 6—Reserved: Read-only bits, always read as 1.
163
Bits 5 and 4—Combination Mode 1 and 0 (CMD1, CMD0): These bits select whether channels
3 and 4 operate in normal mode, complementary PWM mode, or reset-synchronized PWM mode.
Bit 5
CMD1
Bit 4
CMD0
Description
0
0
Channels 3 and 4 operate normally
(Initial value)
1
1
0
Channels 3 and 4 operate together in complementary PWM mode
1
Channels 3 and 4 operate together in reset-synchronized PWM mode
Before selecting reset-synchronized PWM mode or complementary PWM mode, halt the timer
counter or counters that will be used in these modes.
When these bits select complementary PWM mode or reset-synchronized PWM mode, they take
precedence over the setting of the PWM mode bits (PWM4 and PWM3) in TMDR. Settings of
timer sync bits SYNC4 and SYNC3 in the timer synchro register (TSNC) are valid in
complementary PWM mode and reset-synchronized PWM mode, however. When complementary
PWM mode is selected, channels 3 and 4 must not be synchronized (do not set bits SYNC3 and
SYNC4 both to 1 in TSNC).
Bit 3—Buffer Mode B4 (BFB4): Selects whether GRB4 operates normally in channel 4, or
whether GRB4 is buffered by BRB4.
Bit 3
BFB4
Description
0
GRB4 operates normally
1
GRB4 is buffered by BRB4
(Initial value)
Bit 2—Buffer Mode A4 (BFA4): Selects whether GRA4 operates normally in channel 4, or
whether GRA4 is buffered by BRA4.
Bit 2
BFA4
Description
0
GRA4 operates normally
1
GRA4 is buffered by BRA4
(Initial value)
164
Bit 1—Buffer Mode B3 (BFB3): Selects whether GRB3 operates normally in channel 3, or
whether GRB3 is buffered by BRB3.
Bit 1
BFB3
Description
0
GRB3 operates normally
1
GRB3 is buffered by BRB3
(Initial value)
Bit 0—Buffer Mode A3 (BFA3): Selects whether GRA3 operates normally in channel 3, or
whether GRA3 is buffered by BRA3.
Bit 0
BFA3
Description
0
GRA3 operates normally
1
GRA3 is buffered by BRA3
(Initial value)
8.2.5 Timer Output Master Enable Register (TOER)
TOER is an 8-bit readable/writable register that enables or disables output settings for channels 3
and 4.
Bit
7
6
5
4
3
2
1
0
—
—
EXB4
EXA4
EB3
EB4
EA4
EA3
Initial value
1
1
1
1
1
1
1
1
Read/Write
—
—
R/W
R/W
R/W
R/W
R/W
R/W
Reserved bits
Master enable TOCXA4, TOCXB4
These bits enable or disable output
settings for pins TOCXA4 and TOCXB4
Master enable TIOCA3, TIOCB3 , TIOCA4, TIOCB4
These bits enable or disable output settings for pins
TIOCA3, TIOCB3 , TIOCA4, and TIOCB4
TOER is initialized to H'FF by a reset and in standby mode.
Bits 7 and 6—Reserved: Read-only bits, always read as 1.
165
Bit 5—Master Enable TOCXB4 (EXB4): Enables or disables ITU output at pin TOCXB4.
Bit 5
EXB4
Description
0
TOCXB4 output is disabled regardless of TFCR settings (TOCXB4 operates as a generic
input/output pin).
If XTGD = 0, EXB4 is cleared to 0 when input capture A occurs in channel 1.
1
TOCXB4 is enabled for output according to TFCR settings
(Initial value)
Bit 4—Master Enable TOCXA4 (EXA4): Enables or disables ITU output at pin TOCXA4.
Bit 4
EXA4
Description
0
TOCXA4 output is disabled regardless of TFCR settings (TOCXA4 operates as a generic
input/output pin).
If XTGD = 0, EXA4 is cleared to 0 when input capture A occurs in channel 1.
1
TOCXA4 is enabled for output according to TFCR settings
(Initial value)
Bit 3—Master Enable TIOCB3 (EB3): Enables or disables ITU output at pin TIOCB3.
Bit 3
EB3
Description
0
TIOCB3 output is disabled regardless of TIOR3 and TFCR settings (TIOCB3 operates as
a generic input/output pin).
If XTGD = 0, EB3 is cleared to 0 when input capture A occurs in channel 1.
1
TIOCB3 is enabled for output according to TIOR3 and TFCR settings
166
(Initial value)
Bit 2—Master Enable TIOCB4 (EB4): Enables or disables ITU output at pin TIOCB4.
Bit 2
EB4
Description
0
TIOCB4 output is disabled regardless of TIOR4 and TFCR settings (TIOCB4 operates as
a generic input/output pin).
If XTGD = 0, EB4 is cleared to 0 when input capture A occurs in channel 1.
1
TIOCB4 is enabled for output according to TIOR4 and TFCR settings
(Initial value)
Bit 1—Master Enable TIOCA4 (EA4): Enables or disables ITU output at pin TIOCA4.
Bit 1
EA4
Description
0
TIOCA4 output is disabled regardless of TIOR4, TMDR, and TFCR settings (TIOCA4
operates as a generic input/output pin).
If XTGD = 0, EA4 is cleared to 0 when input capture A occurs in channel 1.
1
TIOCA4 is enabled for output according to TIOR4, TMDR, and
TFCR settings
(Initial value)
Bit 0—Master Enable TIOCA3 (EA3): Enables or disables ITU output at pin TIOCA3.
Bit 0
EA3
Description
0
TIOCA3 output is disabled regardless of TIOR3, TMDR, and TFCR settings (TIOCA3
operates as a generic input/output pin).
If XTGD = 0, EA3 is cleared to 0 when input capture A occurs in channel 1.
1
TIOCA3 is enabled for output according to TIOR3, TMDR, and
TFCR settings
167
(Initial value)
8.2.6 Timer Output Control Register (TOCR)
TOCR is an 8-bit readable/writable register that selects externally triggered disabling of output in
complementary PWM mode and reset-synchronized PWM mode, and inverts the output levels.
Bit
7
6
5
4
3
2
1
0
—
—
—
XTGD
—
—
OLS4
OLS3
Initial value
1
1
1
1
1
1
1
1
Read/Write
—
—
—
R/W
—
—
R/W
R/W
Reserved bits
Output level select 3, 4
These bits select output
levels in complementary
PWM mode and resetsynchronized PWM mode
Reserved bits
External trigger disable
Selects externally triggered disabling of output in
complementary PWM mode and reset-synchronized
PWM mode
The settings of the XTGD, OLS4, and OLS3 bits are valid only in complementary PWM mode
and reset-synchronized PWM mode. These settings do not affect other modes.
TOCR is initialized to H'FF by a reset and in standby mode.
Bits 7 to 5—Reserved: Read-only bits, always read as 1.
Bit 4—External Trigger Disable (XTGD): Selects externally triggered disabling of ITU output
in complementary PWM mode and reset-synchronized PWM mode.
Bit 4
XTGD
Description
0
Input capture A in channel 1 is used as an external trigger signal in complementary PWM
mode and reset-synchronized PWM mode.
When an external trigger occurs, bits 5 to 0 in the timer output master enable register
(TOER) are cleared to 0, disabling ITU output.
1
External triggering is disabled
(Initial value)
168
Bits 3 and 2—Reserved: Read-only bits, always read as 1.
Bit 1—Output Level Select 4 (OLS4): Selects output levels in complementary PWM mode and
reset-synchronized PWM mode.
Bit 1
OLS4
Description
0
TIOCA3, TIOCA4, and TIOCB4 outputs are inverted
1
TIOCA3, TIOCA4, and TIOCB4 outputs are not inverted
(Initial value)
Bit 0—Output Level Select 3 (OLS3): Selects output levels in complementary PWM mode and
reset-synchronized PWM mode.
Bit 0
OLS3
Description
0
TIOCB3, TOCXA4, and TOCXB4 outputs are inverted
1
TIOCB3, TOCXA4, and TOCXB4 outputs are not inverted
(Initial value)
8.2.7 Timer Counters (TCNT)
TCNT is a 16-bit counter. The ITU has five TCNTs, one for each channel.
Channel
Abbreviation
Function
0
TCNT0
Up-counter
1
TCNT1
2
TCNT2
Phase counting mode: up/down-counter
Other modes: up-counter
3
TCNT3
4
TCNT4
Complementary PWM mode: up/down-counter
Other modes: up-counter
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Each TCNT is a 16-bit readable/writable register that counts pulse inputs from a clock source. The
clock source is selected by bits TPSC2 to TPSC0 in the timer control register (TCR).
169
TCNT0 and TCNT1 are up-counters. TCNT2 is an up/down-counter in phase counting mode and
an up-counter in other modes. TCNT3 and TCNT4 are up/down-counters in complementary PWM
mode and up-counters in other modes.
TCNT can be cleared to H'0000 by compare match with general register A or B (GRA or GRB) or
by input capture to GRA or GRB (counter clearing function) in the same channel.
When TCNT overflows (changes from H'FFFF to H'0000), the overflow flag (OVF) is set to 1 in
the timer status register (TSR) of the corresponding channel.
When TCNT underflows (changes from H'0000 to H'FFFF), the overflow flag (OVF) is set to 1 in
TSR of the corresponding channel.
The TCNTs are linked to the CPU by an internal 16-bit bus and can be written or read by either
word access or byte access.
Each TCNT is initialized to H'0000 by a reset and in standby mode.
8.2.8 General Registers (GRA, GRB)
The general registers are 16-bit registers. The ITU has 10 general registers, two in each channel.
Channel
Abbreviation
Function
0
GRA0, GRB0
Output compare/input capture register
1
GRA1, GRB1
2
GRA2, GRB2
3
GRA3, GRB3
4
GRA4, GRB4
Output compare/input capture register; can be buffered by buffer
registers BRA and BRB
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
A general register is a 16-bit readable/writable register that can function as either an output
compare register or an input capture register. The function is selected by settings in the timer I/O
control register (TIOR).
When a general register is used as an output compare register, its value is constantly compared
with the TCNT value. When the two values match (compare match), the IMFA or IMFB flag is set
to 1 in the timer status register (TSR). Compare match output can be selected in TIOR.
170
When a general register is used as an input capture register, rising edges, falling edges, or both
edges of an external input capture signal are detected and the current TCNT value is stored in the
general register. The corresponding IMFA or IMFB flag in TSR is set to 1 at the same time. The
valid edge or edges of the input capture signal are selected in TIOR.
TIOR settings are ignored in PWM mode, complementary PWM mode, and reset-synchronized
PWM mode.
General registers are linked to the CPU by an internal 16-bit bus and can be written or read by
either word access or byte access.
General registers are initialized to the output compare function (with no output signal) by a reset
and in standby mode. The initial value is H'FFFF.
8.2.9 Buffer Registers (BRA, BRB)
The buffer registers are 16-bit registers. The ITU has four buffer registers, two each in channels 3
and 4.
Channel
Abbreviation
Function
3
BRA3, BRB3
Used for buffering
4
BRA4, BRB4
• When the corresponding GRA or GRB functions as an output
compare register, BRA or BRB can function as an output compare
buffer register: the BRA or BRB value is automatically transferred
to GRA or GRB at compare match
• When the corresponding GRA or GRB functions as an input
capture register, BRA or BRB can function as an input capture
buffer register: the GRA or GRB value is automatically transferred
to BRA or BRB at input capture
Bit
Initial value
Read/Write
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
A buffer register is a 16-bit readable/writable register that is used when buffering is selected.
Buffering can be selected independently by bits BFB4, BFA4, BFB3, and BFA3 in TFCR.
The buffer register and general register operate as a pair. When the general register functions as an
output compare register, the buffer register functions as an output compare buffer register. When
the general register functions as an input capture register, the buffer register functions as an input
capture buffer register.
171
The buffer registers are linked to the CPU by an internal 16-bit bus and can be written or read by
either word or byte access.
Buffer registers are initialized to H'FFFF by a reset and in standby mode.
8.2.10 Timer Control Registers (TCR)
TCR is an 8-bit register. The ITU has five TCRs, one in each channel.
Channel
Abbreviation
Function
0
TCR0
1
TCR1
2
TCR2
TCR controls the timer counter. The TCRs in all channels are
functionally identical. When phase counting mode is selected in
channel 2, the settings of bits CKEG1 and CKEG0 and TPSC2 to
TPSC0 in TCR2 are ignored.
3
TCR3
4
TCR4
Bit
7
6
5
—
CCLR1
CCLR0
Initial value
1
0
0
0
Read/Write
—
R/W
R/W
R/W
4
3
2
1
0
TPSC2
TPSC1
TPSC0
0
0
0
0
R/W
R/W
R/W
R/W
CKEG1 CKEG0
Timer prescaler 2 to 0
These bits select the
counter clock
Clock edge 1/0
These bits select external clock edges
Counter clear 1/0
These bits select the counter clear source
Reserved bit
Each TCR is an 8-bit readable/writable register that selects the timer counter clock source, selects
the edge or edges of external clock sources, and selects how the counter is cleared.
TCR is initialized to H'80 by a reset and in standby mode.
Bit 7—Reserved: Read-only bit, always read as 1.
172
Bits 6 and 5—Counter Clear 1/0 (CCLR1, CCLR0): These bits select how TCNT is cleared.
Bit 6
CCLR1
Bit 5
CCLR0
Description
0
0
TCNT is not cleared
1
(Initial value)
capture*1
1
TCNT is cleared by GRA compare match or input
0
TCNT is cleared by GRB compare match or input capture*1
1
Synchronous clear: TCNT is cleared in synchronization with other
synchronized timers*2
Notes: 1. TCNT is cleared by compare match when the general register functions as a compare
match register, and by input capture when the general register functions as an input
capture register.
2. Selected in the timer synchro register (TSNC).
Bits 4 and 3—Clock Edge 1/0 (CKEG1, CKEG0): These bits select external clock input edges
when an external clock source is used.
Bit 4
CKEG1
Bit 3
CKEG0
Description
0
0
Count rising edges
1
Count falling edges
—
Count both edges
1
(Initial value)
When channel 2 is set to phase counting mode, bits CKEG1 and CKEG0 in TCR2 are ignored.
Phase counting takes precedence.
173
Bits 2 to 0—Timer Prescaler 2 to 0 (TPSC2 to TPSC0): These bits select the counter clock
source.
Bit 2
TPSC2
Bit 1
TPSC1
Bit 0
TPSC0
Function
0
0
0
Internal clock: ø
1
Internal clock: ø/2
0
Internal clock: ø/4
1
Internal clock: ø/8
0
External clock A: TCLKA input
1
External clock B: TCLKB input
0
External clock C: TCLKC input
1
External clock D: TCLKD input
1
1
0
1
(Initial value)
When bit TPSC2 is cleared to 0 an internal clock source is selected, and the timer counts only
falling edges. When bit TPSC2 is set to 1 an external clock source is selected, and the timer counts
the edge or edges selected by bits CKEG1 and CKEG0.
When channel 2 is set to phase counting mode (MDF = 1 in TMDR), the settings of bits TPSC2 to
TPSC0 in TCR2 are ignored. Phase counting takes precedence.
8.2.11 Timer I/O Control Register (TIOR)
TIOR is an 8-bit register. The ITU has five TIORs, one in each channel.
Channel
Abbreviation
Function
0
TIOR0
1
TIOR1
2
TIOR2
TIOR controls the general registers. Some functions differ in PWM
mode. TIOR3 and TIOR4 settings are ignored when complementary
PWM mode or reset-synchronized PWM mode is selected in
channels 3 and 4.
3
TIOR3
4
TIOR4
174
Bit
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
I/O control A2 to A0
These bits select GRA
functions
Reserved bit
I/O control B2 to B0
These bits select GRB functions
Reserved bit
Each TIOR is an 8-bit readable/writable register that selects the output compare or input capture
function for GRA and GRB, and specifies the functions of the TIOCA and TIOCB pins. If the
output compare function is selected, TIOR also selects the type of output. If input capture is
selected, TIOR also selects the edge or edges of the input capture signal.
TIOR is initialized to H'88 by a reset and in standby mode.
Bit 7—Reserved: Read-only bit, always read as 1.
Bits 6 to 4—I/O Control B2 to B0 (IOB2 to IOB0): These bits select the GRB function.
Bit 6
IOB2
Bit 5
IOB1
Bit 4
IOB0
0
0
0
1
1
1
0
GRB is an output
compare register
No output at compare match
0 output at GRB compare
(Initial value)
match*1
0
1 output at GRB compare match*1
1
Output toggles at GRB compare match
(1 output in channel 2)*1, *2
0
1
1
Function
0
GRB is an input
capture register
GRB captures rising edge of input
GRB captures falling edge of input
GRB captures both edges of input
1
Notes: 1. After a reset, the output is 0 until the first compare match.
2. Channel 2 output cannot be toggled by compare match. This setting selects 1 output
instead.
175
Bit 3—Reserved: Read-only bit, always read as 1.
Bits 2 to 0—I/O Control A2 to A0 (IOA2 to IOA0): These bits select the GRA function.
Bit 2
IOA2
Bit 1
IOA1
Bit 0
IOA0
0
0
0
1
1
1
0
GRA is an output
compare register
No output at compare match
(Initial value)
0 output at GRA compare match*1
0
1 output at GRA compare match*1
1
Output toggles at GRA compare match
(1 output in channel 2)*1, *2
0
1
1
Function
GRA is an input
capture register
GRA captures rising edge of input
GRA captures falling edge of input
0
GRA captures both edges of input
1
Notes: 1. After a reset, the output is 0 until the first compare match.
2. Channel 2 output cannot be toggled by compare match. This setting selects 1 output
instead.
8.2.12 Timer Status Register (TSR)
TSR is an 8-bit register. The ITU has five TSRs, one in each channel.
Channel
Abbreviation
Function
0
TSR0
Indicates input capture, compare match, and overflow status
1
TSR1
2
TSR2
3
TSR3
4
TSR4
176
7
6
5
4
3
2
1
0
—
—
—
—
—
OVF
IMFB
IMFA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/(W)*
R/(W)*
R/(W)*
Bit
Reserved bits
Overflow flag
Status flag indicating
overflow or underflow
Input capture/compare match flag B
Status flag indicating GRB compare
match or input capture
Input capture/compare match flag A
Status flag indicating GRA compare
match or input capture
Note: * Only 0 can be written, to clear the flag.
Each TSR is an 8-bit readable/writable register containing flags that indicate TCNT overflow or
underflow and GRA or GRB compare match or input capture. These flags are interrupt sources
and generate CPU interrupts if enabled by corresponding bits in the timer interrupt enable register
(TIER).
TSR is initialized to H'F8 by a reset and in standby mode.
Bits 7 to 3—Reserved: Read-only bits, always read as 1.
Bit 2—Overflow Flag (OVF): This status flag indicates TCNT overflow or underflow.
Bit 2
OVF
Description
0
[Clearing condition]
Read OVF when OVF = 1, then write 0 in OVF
(Initial value)
1
[Setting condition]
TCNT overflowed from H'FFFF to H'0000, or underflowed from H'0000 to H'FFFF*
Notes: * TCNT underflow occurs when TCNT operates as an up/down-counter. Underflow occurs
only under the following conditions:
1. Channel 2 operates in phase counting mode (MDF = 1 in TMDR)
2. Channels 3 and 4 operate in complementary PWM mode (CMD1 = 1 and CMD0 = 0 in
TFCR)
177
Bit 1—Input Capture/Compare Match Flag B (IMFB): This status flag indicates GRB
compare match or input capture events.
Bit 1
IMFB
Description
0
[Clearing condition]
Read IMFB when IMFB = 1, then write 0 in IMFB
(Initial value)
1
[Setting conditions]
TCNT = GRB when GRB functions as a compare match register.
TCNT value is transferred to GRB by an input capture signal, when GRB functions as
an input capture register.
Bit 0—Input Capture/Compare Match Flag A (IMFA): This status flag indicates GRA
compare match or input capture events.
Bit 0
IMFA
Description
0
[Clearing condition]
Read IMFA when IMFA = 1, then write 0 in IMFA.
1
[Setting conditions]
TCNT = GRA when GRA functions as a compare match register.
TCNT value is transferred to GRA by an input capture signal, when GRA functions
as an input capture register.
178
(Initial value)
8.2.13 Timer Interrupt Enable Register (TIER)
TIER is an 8-bit register. The ITU has five TIERs, one in each channel.
Channel
Abbreviation
Function
0
TIER0
Enables or disables interrupt requests.
1
TIER1
2
TIER2
3
TIER3
4
TIER4
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
OVIE
IMIEB
IMIEA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Reserved bits
Overflow interrupt enable
Enables or disables OVF
interrupts
Input capture/compare match
interrupt enable B
Enables or disables IMFB interrupts
Input capture/compare match
interrupt enable A
Enables or disables IMFA
interrupts
Each TIER is an 8-bit readable/writable register that enables and disables overflow interrupt
requests and general register compare match and input capture interrupt requests.
TIER is initialized to H'F8 by a reset and in standby mode.
Bits 7 to 3—Reserved: Read-only bits, always read as 1.
179
Bit 2—Overflow Interrupt Enable (OVIE): Enables or disables the interrupt requested by the
overflow flag (OVF) in TSR when OVF is set to 1.
Bit 2
OVIE
Description
0
OVI interrupt requested by OVF is disabled
1
OVI interrupt requested by OVF is enabled
(Initial value)
Bit 1—Input Capture/Compare Match Interrupt Enable B (IMIEB): Enables or disables the
interrupt requested by the IMFB flag in TSR when IMFB is set to 1.
Bit 1
IMIEB
Description
0
IMIB interrupt requested by IMFB is disabled
1
IMIB interrupt requested by IMFB is enabled
(Initial value)
Bit 0—Input Capture/Compare Match Interrupt Enable A (IMIEA): Enables or disables the
interrupt requested by the IMFA flag in TSR when IMFA is set to 1.
Bit 0
IMIEA
Description
0
IMIA interrupt requested by IMFA is disabled
1
IMIA interrupt requested by IMFA is enabled
180
(Initial value)
8.3 CPU Interface
8.3.1 16-Bit Accessible Registers
The timer counters (TCNTs), general registers A and B (GRAs and GRBs), and buffer registers A
and B (BRAs and BRBs) are 16-bit registers, and are linked to the CPU by an internal 16-bit data
bus. These registers can be written or read a word at a time, or a byte at a time.
Figures 8-6 and 8-7 show examples of word access to a timer counter (TCNT). Figures 8-8, 8-9,
8-10, and 8-11 show examples of byte access to TCNTH and TCNTL.
On-chip data bus
H
CPU
H
L
Bus interface
L
TCNTH
Module
data bus
TCNTL
Figure 8-6 Access to Timer Counter (CPU Writes to TCNT, Word)
On-chip data bus
H
CPU
L
H
Bus interface
L
TCNTH
TCNTL
Figure 8-7 Access to Timer Counter (CPU Reads TCNT, Word)
181
Module
data bus
On-chip data bus
H
CPU
L
H
Bus interface
L
TCNTH
Module
data bus
TCNTL
Figure 8-8 Access to Timer Counter (CPU Writes to TCNT, Upper Byte)
On-chip data bus
H
CPU
L
H
Bus interface
L
TCNTH
Module
data bus
TCNTL
Figure 8-9 Access to Timer Counter (CPU Writes to TCNT, Lower Byte)
On-chip data bus
H
CPU
L
H
Bus interface
L
TCNTH
TCNTL
Figure 8-10 Access to Timer Counter (CPU Reads TCNT, Upper Byte)
182
Module
data bus
On-chip data bus
H
CPU
H
L
Bus interface
L
TCNTH
Module
data bus
TCNTL
Figure 8-11 Access to Timer Counter (CPU Reads TCNT, Lower Byte)
8.3.2 8-Bit Accessible Registers
The registers other than the timer counters, general registers, and buffer registers are 8-bit
registers. These registers are linked to the CPU by an internal 8-bit data bus.
Figures 8-12 and 8-13 show examples of byte read and write access to a TCR.
If a word-size data transfer instruction is executed, two byte transfers are performed.
On-chip data bus
H
CPU
L
H
Bus interface
L
TCR
Figure 8-12 TCR Access (CPU Writes to TCR)
183
Module
data bus
On-chip data bus
H
CPU
L
H
Bus interface
L
TCR
Figure 8-13 TCR Access (CPU Reads TCR)
184
Module
data bus
8.4 Operation
8.4.1 Overview
A summary of operations in the various modes is given below.
Normal Operation: Each channel has a timer counter and general registers. The timer counter
counts up, and can operate as a free-running counter, periodic counter, or external event counter.
General registers A and B can be used for input capture or output compare.
Synchronous Operation: The timer counters in designated channels are preset synchronously.
Data written to the timer counter in any one of these channels is simultaneously written to the
timer counters in the other channels as well. The timer counters can also be cleared synchronously
if so designated by the CCLR1 and CCLR0 bits in the TCRs.
PWM Mode: A PWM waveform is output from the TIOCA pin. The output goes to 1 at compare
match A and to 0 at compare match B. The duty cycle can be varied from 0% to 100% depending
on the settings of GRA and GRB. When a channel is set to PWM mode, its GRA and GRB
automatically become output compare registers.
Reset-Synchronized PWM Mode: Channels 3 and 4 are paired for three-phase PWM output with
complementary waveforms. (The three phases are related by having a common transition point.)
When reset-synchronized PWM mode is selected GRA3, GRB3, GRA4, and GRB4 automatically
function as output compare registers, TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4, and
TOCXB4 function as PWM output pins, and TCNT3 operates as an up-counter. TCNT4 operates
independently, and is not compared with GRA4 or GRB4.
Complementary PWM Mode: Channels 3 and 4 are paired for three-phase PWM output with
non-overlapping complementary waveforms. When complementary PWM mode is selected
GRA3, GRB3, GRA4, and GRB4 automatically function as output compare registers, and
TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4, and TOCXB4 function as PWM output pins.
TCNT3 and TCNT4 operate as up/down-counters.
Phase Counting Mode: The phase relationship between two clock signals input at TCLKA and
TCLKB is detected and TCNT2 counts up or down accordingly. When phase counting mode is
selected TCLKA and TCLKB become clock input pins and TCNT2 operates as an up/downcounter.
185
Buffering
•
If the general register is an output compare register
When compare match occurs the buffer register value is transferred to the general register.
•
If the general register is an input capture register
When input capture occurs the TCNT value is transferred to the general register, and the
previous general register value is transferred to the buffer register.
•
Complementary PWM mode
The buffer register value is transferred to the general register when TCNT3 and TCNT4
change counting direction.
•
Reset-synchronized PWM mode
The buffer register value is transferred to the general register at GRA3 compare match.
8.4.2 Basic Functions
Counter Operation: When one of bits STR0 to STR4 is set to 1 in the timer start register
(TSTR), the timer counter (TCNT) in the corresponding channel starts counting. The counting can
be free-running or periodic.
•
Sample setup procedure for counter
Figure 8-14 shows a sample procedure for setting up a counter.
186
Counter setup
Select counter clock
Type of counting?
1
No
Yes
Free-running counting
Periodic counting
Select counter clear source
2
Select output compare
register function
3
Set period
4
Start counter
5
Start counter
Periodic counter
5
Free-running counter
Figure 8-14 Counter Setup Procedure (Example)
1.
2.
3.
4.
5.
Set bits TPSC2 to TPSC0 in TCR to select the counter clock source. If an external clock
source is selected, set bits CKEG1 and CKEG0 in TCR to select the desired edge(s) of the
external clock signal.
For periodic counting, set CCLR1 and CCLR0 in TCR to have TCNT cleared at GRA
compare match or GRB compare match.
Set TIOR to select the output compare function of GRA or GRB, whichever was selected in
step 2.
Write the count period in GRA or GRB, whichever was selected in step 2.
Set the STR bit to 1 in TSTR to start the timer counter.
187
•
Free-running and periodic counter operation
A reset leaves the counters (TCNTs) in ITU channels 0 to 4 all set as free-running counters. A
free-running counter starts counting up when the corresponding bit in TSTR is set to 1. When
the count overflows from H'FFFF to H'0000, the overflow flag (OVF) is set to 1 in the timer
status register (TSR). If the corresponding OVIE bit is set to 1 in the timer interrupt enable
register, a CPU interrupt is requested. After the overflow, the counter continues counting up
from H'0000. Figure 8-15 illustrates free-running counting.
TCNT value
H'FFFF
H'0000
Time
STR0 to
STR4 bit
OVF
Figure 8-15 Free-Running Counter Operation
When a channel is set to have its counter cleared by compare match, in that channel TCNT
operates as a periodic counter. Select the output compare function of GRA or GRB, set bit
CCLR1 or CCLR0 in the timer control register (TCR) to have the counter cleared by compare
match, and set the count period in GRA or GRB. After these settings, the counter starts
counting up as a periodic counter when the corresponding bit is set to 1 in TSTR. When the
count matches GRA or GRB, the IMFA or IMFB flag is set to 1 in TSR and the counter is
cleared to H'0000. If the corresponding IMIEA or IMIEB bit is set to 1 in TIER, a CPU
interrupt is requested at this time. After the compare match, TCNT continues counting up
from H'0000. Figure 8-16 illustrates periodic counting.
188
TCNT value
Counter cleared by general
register compare match
GR
Time
H'0000
STR bit
IMF
Figure 8-16 Periodic Counter Operation
•
Count timing
— Internal clock source
Bits TPSC2 to TPSC0 in TCR select the system clock (ø) or one of three internal clock
sources obtained by prescaling the system clock (ø/2, ø/4, ø/8).
Figure 8-17 shows the timing.
ø
Internal
clock
TCNT input
TCNT
N–1
N
Figure 8-17 Count Timing for Internal Clock Sources
189
N+1
— External clock source
Bits TPSC2 to TPSC0 in TCR select an external clock input pin (TCLKA to TCLKD),
and its valid edge or edges are selected by bits CKEG1 and CKEG0. The rising edge,
falling edge, or both edges can be selected.
The pulse width of the external clock signal must be at least 1.5 system clocks when a
single edge is selected, and at least 2.5 system clocks when both edges are selected.
Shorter pulses will not be counted correctly.
Figure 8-18 shows the timing when both edges are detected.
ø
External
clock input
TCNT input
TCNT
N–1
N
N+1
Figure 8-18 Count Timing for External Clock Sources (when Both Edges are Detected)
190
Waveform Output by Compare Match: In ITU channels 0, 1, 3, and 4, compare match A or B
can cause the output at the TIOCA or TIOCB pin to go to 0, go to 1, or toggle. In channel 2 the
output can only go to 0 or go to 1.
•
Sample setup procedure for waveform output by compare match
Figure 8-19 shows a sample procedure for setting up waveform output by compare match.
Output setup
1. Select the compare match output mode (0, 1, or
toggle) in TIOR. When a waveform output mode
is selected, the pin switches from its generic input/
output function to the output compare function
(TIOCA or TIOCB). An output compare pin outputs
0 until the first compare match occurs.
Select waveform
output mode
1
Set output timing
2
2. Set a value in GRA or GRB to designate the
compare match timing.
Start counter
3
3. Set the STR bit to 1 in TSTR to start the timer
counter.
Waveform output
Figure 8-19 Setup Procedure for Waveform Output by Compare Match (Example)
•
Examples of waveform output
Figure 8-20 shows examples of 0 and 1 output. TCNT operates as a free-running counter, 0
output is selected for compare match A, and 1 output is selected for compare match B. When
the pin is already at the selected output level, the pin level does not change.
191
TCNT value
H'FFFF
GRB
GRA
H'0000
TIOCB
TIOCA
Time
No change
No change
No change
No change
1 output
0 output
Figure 8-20 0 and 1 Output (Examples)
Figure 8-21 shows examples of toggle output. TCNT operates as a periodic counter, cleared
by compare match B. Toggle output is selected for both compare match A and B.
TCNT value
Counter cleared by compare match with GRB
GRB
GRA
H'0000
Time
TIOCB
Toggle
output
TIOCA
Toggle
output
Figure 8-21 Toggle Output (Example)
192
•
Output compare timing
The compare match signal is generated in the last state in which TCNT and the general
register match (when TCNT changes from the matching value to the next value). When the
compare match signal is generated, the output value selected in TIOR is output at the output
compare pin (TIOCA or TIOCB). When TCNT matches a general register, the compare
match signal is not generated until the next counter clock pulse.
Figure 8-22 shows the output compare timing.
ø
TCNT input
clock
TCNT
N
GR
N
N+1
Compare
match signal
TIOCA,
TIOCB
Figure 8-22 Output Compare Timing
Input Capture Function: The TCNT value can be captured into a general register when a
transition occurs at an input capture/output compare pin (TIOCA or TIOCB). Capture can take
place on the rising edge, falling edge, or both edges. The input capture function can be used to
measure pulse width or period.
•
Sample setup procedure for input capture
Figure 8-23 shows a sample procedure for setting up input capture.
193
Input selection
Select input-capture input
1
Start counter
2
1. Set TIOR to select the input capture function of a
general register and the rising edge, falling edge,
or both edges of the input capture signal. Clear the
port data direction bit to 0 before making these
TIOR settings.
2. Set the STR bit to 1 in TSTR to start the timer
counter.
Input capture
Figure 8-23 Setup Procedure for Input Capture (Example)
•
Examples of input capture
Figure 8-24 illustrates input capture when the falling edge of TIOCB and both edges of
TIOCA are selected as capture edges. TCNT is cleared by input capture into GRB.
TCNT value
Counter cleared by TIOCB
input (falling edge)
H'0180
H'0160
H'0005
H'0000
Time
TIOCB
TIOCA
GRA
H'0005
H'0160
GRB
H'0180
Figure 8-24 Input Capture (Example)
194
•
Input capture signal timing
Input capture on the rising edge, falling edge, or both edges can be selected by settings in
TIOR. Figure 8-25 shows the timing when the rising edge is selected. The pulse width of the
input capture signal must be at least 1.5 system clocks for single-edge capture, and 2.5 system
clocks for capture of both edges.
ø
Input-capture input
Internal input
capture signal
N
TCNT
N
GRA, GRB
Figure 8-25 Input Capture Signal Timing
195
8.4.3 Synchronization
The synchronization function enables two or more timer counters to be synchronized by writing
the same data to them simultaneously (synchronous preset). With appropriate TCR settings, two or
more timer counters can also be cleared simultaneously (synchronous clear). Synchronization
enables additional general registers to be associated with a single time base. Synchronization can
be selected for all channels (0 to 4).
Sample Setup Procedure for Synchronization: Figure 8-26 shows a sample procedure for
setting up synchronization.
Setup for synchronization
Select synchronization
1
Synchronous preset
Write to TCNT
Synchronous clear
2
Clearing
synchronized to this
channel?
No
Yes
Synchronous preset
Select counter clear source
3
Select counter clear source
4
Start counter
5
Start counter
5
Counter clear
Synchronous clear
1. Set the SYNC bits to 1 in TSNC for the channels to be synchronized.
2. When a value is written in TCNT in one of the synchronized channels, the same value is
simultaneously written in TCNT in the other channels (synchronized preset).
3. Set the CCLR1 or CCLR0 bit in TCR to have the counter cleared by compare match or input capture.
4. Set the CCLR1 and CCLR0 bits in TCR to have the counter cleared synchronously.
5. Set the STR bits in TSTR to 1 to start the synchronized counters.
Figure 8-26 Setup Procedure for Synchronization (Example)
196
Example of Synchronization: Figure 8-27 shows an example of synchronization. Channels 0, 1,
and 2 are synchronized, and are set to operate in PWM mode. Channel 0 is set for counter clearing
by compare match with GRB0. Channels 1 and 2 are set for synchronous counter clearing. The
timer counters in channels 0, 1, and 2 are synchronously preset, and are synchronously cleared by
compare match with GRB0. A three-phase PWM waveform is output from pins TIOCA0,
TIOCA1, and TIOCA2. For further information on PWM mode, see section 8.4.4, PWM Mode.
Value of TCNT0 to TCNT2
Cleared by compare match with GRB0
GRB0
GRB1
GRA0
GRB2
GRA1
GRA2
Time
TIOCA0
TIOCA1
TIOCA2
Figure 8-27 Synchronization (Example)
197
8.4.4 PWM Mode
In PWM mode GRA and GRB are paired and a PWM waveform is output from the TIOCA pin.
GRA specifies the time at which the PWM output changes to 1. GRB specifies the time at which
the PWM output changes to 0. If either GRA or GRB is selected as the counter clear source, a
PWM waveform with a duty cycle from 0% to 100% is output at the TIOCA pin. PWM mode can
be selected in all channels (0 to 4).
Table 8-4 summarizes the PWM output pins and corresponding registers. If the same value is set
in GRA and GRB, the output does not change when compare match occurs.
Table 8-4 PWM Output Pins and Registers
Channel
Output Pin
1 Output
0 Output
0
TIOCA0
GRA0
GRB0
1
TIOCA1
GRA1
GRB1
2
TIOCA2
GRA2
GRB2
3
TIOCA3
GRA3
GRB3
4
TIOCA4
GRA4
GRB4
198
Sample Setup Procedure for PWM Mode: Figure 8-28 shows a sample procedure for setting up
PWM mode.
PWM mode
Select counter clock
1
Select counter clear source
2
Set GRA
3
Set GRB
4
Select PWM mode
5
Start counter
6
1. Set bits TPSC2 to TPSC0 in TCR to
select the counter clock source. If an
external clock source is selected, set
bits CKEG1 and CKEG0 in TCR to
select the desired edge(s) of the
external clock signal.
2. Set bits CCLR1 and CCLR0 in TCR
to select the counter clear source.
3. Set the time at which the PWM
waveform should go to 1 in GRA.
4. Set the time at which the PWM
waveform should go to 0 in GRB.
5. Set the PWM bit in TMDR to select
PWM mode. When PWM mode is
selected, regardless of the TIOR
contents, GRA and GRB become
output compare registers specifying
the times at which the PWM
goes to 1 and 0. The TIOCA pin
automatically becomes the PWM
output pin. The TIOCB pin conforms
to the settings of bits IOB1 and IOB0
in TIOR. If TIOCB output is not
desired, clear both IOB1 and IOB0 to 0.
6. Set the STR bit to 1 in TSTR to start
the timer counter.
PWM mode
Figure 8-28 Setup Procedure for PWM Mode (Example)
199
Examples of PWM Mode: Figure 8-29 shows examples of operation in PWM mode. The PWM
waveform is output from the TIOCA pin. The output goes to 1 at compare match with GRA, and
to 0 at compare match with GRB.
In the examples shown, TCNT is cleared by compare match with GRA or GRB. Synchronized
operation and free-running counting are also possible.
TCNT value
Counter cleared by compare match with GRA
GRA
GRB
Time
H'0000
TIOCA
a. Counter cleared by GRA
TCNT value
Counter cleared by compare match with GRB
GRB
GRA
Time
H'0000
TIOCA
b. Counter cleared by GRB
Figure 8-29 PWM Mode (Example 1)
200
Figure 8-30 shows examples of the output of PWM waveforms with duty cycles of 0% and 100%.
If the counter is cleared by compare match with GRB, and GRA is set to a higher value than GRB,
the duty cycle is 0%. If the counter is cleared by compare match with GRA, and GRB is set to a
higher value than GRA, the duty cycle is 100%.
TCNT value
Counter cleared by compare match with GRB
GRB
GRA
H'0000
Time
TIOCA
Write to GRA
Write to GRA
a. 0% duty cycle
TCNT value
Counter cleared by compare match with GRA
GRA
GRB
H'0000
Time
TIOCA
Write to GRB
Write to GRB
b. 100% duty cycle
Figure 8-30 PWM Mode (Example 2)
201
8.4.5 Reset-Synchronized PWM Mode
In reset-synchronized PWM mode channels 3 and 4 are combined to produce three pairs of
complementary PWM waveforms, all having one waveform transition point in common.
When reset-synchronized PWM mode is selected TIOCA3, TIOCB3, TIOCA4, TOCXA4,
TIOCB4, and TOCXB4 automatically become PWM output pins, and TCNT3 functions as an upcounter.
Table 8-5 lists the PWM output pins. Table 8-6 summarizes the register settings.
Table 8-5 Output Pins in Reset-Synchronized PWM Mode
Channel
Output Pin
Description
3
TIOCA3
PWM output 1
TIOCB3
PWM output 1´ (complementary waveform to PWM output 1)
TIOCA4
PWM output 2
TOCXA4
PWM output 2´ (complementary waveform to PWM output 2)
TIOCB4
PWM output 3
TOCXB4
PWM output 3´ (complementary waveform to PWM output 3)
4
Table 8-6 Register Settings in Reset-Synchronized PWM Mode
Register
Setting
TCNT3
Initially set to H'0000
TCNT4
Not used (operates independently)
GRA3
Specifies the count period of TCNT3
GRB3
Specifies a transition point of PWM waveforms output from TIOCA3 and TIOCB3
GRA4
Specifies a transition point of PWM waveforms output from TIOCA4 and TOCXA4
GRB4
Specifies a transition point of PWM waveforms output from TIOCB4 and TOCXB4
202
Sample Setup Procedure for Reset-Synchronized PWM Mode: Figure 8-31 shows a sample
procedure for setting up reset-synchronized PWM mode.
Reset-synchronized PWM mode
Stop counter
1
Select counter clock
2
Select counter clear source
3
Select reset-synchronized
PWM mode
4
Set TCNT
5
Set general registers
6
Start counter
7
1. Clear the STR3 bit in TSTR to 0 to
halt TCNT3. Reset-synchronized
PWM mode must be set up while
TCNT3 is halted.
2. Set bits TPSC2 to TPSC0 in TCR to
select the counter clock source for
channel 3. If an external clock source
is selected, select the external clock
edge(s) with bits CKEG1 and CKEG0
in TCR.
3. Set bits CCLR1 and CCLR0 in TCR3
to select GRA3 compare match as
the counter clear source.
4. Set bits CMD1 and CMD0 in TFCR to
select reset-synchronized PWM mode.
TIOCA3, TIOCB3, TIOCA4, TIOCB4,
TOCXA4, and TOCXB4 automatically
become PWM output pins.
5. Preset TCNT3 to H'0000. TCNT4
need not be preset.
6. GRA3 is the waveform period register.
Set the waveform period value in
GRA3. Set transition times of the
PWM output waveforms in GRB3,
GRA4, and GRB4. Set times within
the compare match range of TCNT3.
X ≤ GRA3 (X: setting value)
7. Set the STR3 bit in TSTR to 1 to start
TCNT3.
Reset-synchronized PWM mode
Figure 8-31 Setup Procedure for Reset-Synchronized PWM Mode (Example)
203
Example of Reset-Synchronized PWM Mode: Figure 8-32 shows an example of operation in
reset-synchronized PWM mode. TCNT3 operates as an up-counter in this mode. TCNT4 operates
independently, detached from GRA4 and GRB4. When TCNT3 matches GRA3, TCNT3 is
cleared and resumes counting from H'0000. The PWM outputs toggle at compare match with
GRB3, GRA4, GRB4, and TCNT3 respectively, and all toggle when the counter is cleared.
TCNT3 value
Counter cleared at compare match with GRA3
GRA3
GRB3
GRA4
GRB4
H'0000
Time
TIOCA3
TIOCB3
TIOCA4
TOCXA4
TIOCB4
TOCXB4
Figure 8-32 Operation in Reset-Synchronized PWM Mode (Example)
(when OLS3 = OLS4 = 1)
For the settings and operation when reset-synchronized PWM mode and buffer mode are both
selected, see section 8.4.8, Buffering.
204
8.4.6 Complementary PWM Mode
In complementary PWM mode channels 3 and 4 are combined to output three pairs of
complementary, non-overlapping PWM waveforms.
When complementary PWM mode is selected TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4,
and TOCXB4 automatically become PWM output pins, and TCNT3 and TCNT4 function as
up/down-counters.
Table 8-7 lists the PWM output pins. Table 8-8 summarizes the register settings.
Table 8-7 Output Pins in Complementary PWM Mode
Channel
Output Pin
Description
3
TIOCA3
PWM output 1
TIOCB3
PWM output 1´ (non-overlapping complementary waveform to PWM
output 1)
TIOCA4
PWM output 2
TOCXA4
PWM output 2´ (non-overlapping complementary waveform to PWM
output 2)
TIOCB4
PWM output 3
TOCXB4
PWM output 3´ (non-overlapping complementary waveform to PWM
output 3)
4
Table 8-8 Register Settings in Complementary PWM Mode
Register
Setting
TCNT3
Initially specifies the non-overlap margin (difference to TCNT4)
TCNT4
Initially set to H'0000
GRA3
Specifies the upper limit value of TCNT3 minus 1
GRB3
Specifies a transition point of PWM waveforms output from TIOCA3 and TIOCB3
GRA4
Specifies a transition point of PWM waveforms output from TIOCA4 and TOCXA4
GRB4
Specifies a transition point of PWM waveforms output from TIOCB4 and TOCXB4
205
Setup Procedure for Complementary PWM Mode: Figure 8-33 shows a sample procedure for
setting up complementary PWM mode.
Complementary PWM mode
Stop counting
1. Clear bits STR3 and STR4 to 0 in
TSTR to halt the timer counters.
Complementary PWM mode must be
set up while TCNT3 and TCNT4 are
halted.
1
Select counter clock
2
Select complementary
PWM mode
3
Set TCNTs
4
Set general registers
5
Start counters
6
2. Set bits TPSC2 to TPSC0 in TCR to
select the same counter clock source
for channels 3 and 4. If an external
clock source is selected, select the
external clock edge(s) with bits
CKEG1 and CKEG0 in TCR. Do not
select any counter clear source
with bits CCLR1 and CCLR0 in TCR.
3. Set bits CMD1 and CMD0 in TFCR
to select complementary PWM mode.
TIOCA3, TIOCB3, TIOCA4, TIOCB4,
TOCXA4, and TOCXB4 automatically
become PWM output pins.
4. Clear TCNT4 to H'0000. Set the
non-overlap margin in TCNT3. Do not
set TCNT3 and TCNT4 to the same
value.
5. GRA3 is the waveform period
register. Set the upper limit value of
TCNT3 minus 1 in GRA3. Set
transition times of the PWM output
waveforms in GRB3, GRA4, and
GRB4. Set times within the compare
match range of TCNT3 and TCNT4.
T ≤ X (X: initial setting of GRB3,
GRA4, or GRB4. T: initial setting of
TCNT3)
Complementary PWM mode
6. Set bits STR3 and STR4 in TSTR to
1 to start TCNT3 and TCNT4.
Note: After exiting complementary PWM mode, to resume operating in complementary
PWM mode, follow the entire setup procedure from step 1 again.
Figure 8-33 Setup Procedure for Complementary PWM Mode (Example)
206
Clearing Complementary PWM Mode: Figure 8-34 shows a sample procedure for clearing
complementary PWM mode.
Complementary PWM mode
Clear complementary mode
Stop counting
1
1. Clear bit CMD1 in TFCR to 0, and set
channels 3 and 4 to normal operating
mode.
2
2. After setting channels 3 and 4 to normal
operating mode, wait at least one clock
count before clearing bits STR3 and
STR4 of TSTR to 0 to stop the counter
operation of TCNT3 and TCNT4.
Normal operation
Figure 8-34 Clearing Procedure for Complementary PWM Mode (Example)
207
Examples of Complementary PWM Mode: Figure 8-35 shows an example of operation in
complementary PWM mode. TCNT3 and TCNT4 operate as up/down-counters, counting down
from compare match between TCNT3 and GRA3 and counting up from the point at which
TCNT4 underflows. During each up-and-down counting cycle, PWM waveforms are generated by
compare match with general registers GRB3, GRA4, and GRB4. Since TCNT3 is initially set to a
higher value than TCNT4, compare match events occur in the sequence TCNT3, TCNT4, TCNT4,
TCNT3.
TCNT3 and
TCNT4 values
Down-counting starts at compare
match between TCNT3 and GRA3
GRA3
TCNT3
GRB3
GRA4
GRB4
TCNT4
Time
H'0000
TIOCA3
Up-counting starts when
TCNT4 underflows
TIOCB3
TIOCA4
TOCXA4
TIOCB4
TOCXB4
Figure 8-35 Operation in Complementary PWM Mode (Example 1)
(when OLS3 = OLS4 = 1)
208
Figure 8-36 shows examples of waveforms with 0% and 100% duty cycles (in one phase) in
complementary PWM mode. In this example the outputs change at compare match with GRB3, so
waveforms with duty cycles of 0% or 100% can be output by setting GRB3 to a value larger than
GRA3. The duty cycle can be changed easily during operation by use of the buffer registers. For
further information see section 8.4.8, Buffering.
TCNT3 and
TCNT4 values
GRA3
GRB3
Time
H'0000
TIOCA3
0% duty cycle
TIOCB3
a. 0% duty cycle
TCNT3 and
TCNT4 values
GRA3
GRB3
H'0000
Time
TIOCA3
TIOCB3
100% duty cycle
b. 100% duty cycle
Figure 8-36 Operation in Complementary PWM Mode (Example 2)
(when OLS3 = OLS4 = 1)
209
In complementary PWM mode, TCNT3 and TCNT4 overshoot and undershoot at the transitions
between up-counting and down-counting. The setting conditions for the IMFA bit in channel 3 and
the OVF bit in channel 4 differ from the usual conditions. In buffered operation the buffer transfer
conditions also differ. Timing diagrams are shown in figures 8-37 and 8-38.
TCNT3
N–1
N
N+1
GRA3
N
N–1
N
Flag not set
IMFA
Set to 1
Buffer transfer
signal (BR to GR)
GR
Buffer transfer
No buffer transfer
Figure 8-37 Overshoot Timing
210
Underflow
TCNT4
H'0001
H'0000
Overflow
H'FFFF
H'0000
Flag not set
OVF
Set to 1
Buffer transfer
signal (BR to GR)
GR
Buffer transfer
No buffer transfer
Figure 8-38 Undershoot Timing
In channel 3, IMFA is set to 1 only during up-counting. In channel 4, OVF is set to 1 only when an
underflow occurs. When buffering is selected, buffer register contents are transferred to the
general register at compare match A3 during up-counting, and when TCNT4 underflows.
General Register Settings in Complementary PWM Mode: When setting up general registers
for complementary PWM mode or changing their settings during operation, note the following
points.
•
Initial settings
Do not set values from H'0000 to T – 1 (where T is the initial value of TCNT3). After the
counters start and the first compare match A3 event has occurred, however, settings in this
range also become possible.
•
Changing settings
Use the buffer registers. Correct waveform output may not be obtained if a general register is
written to directly.
•
Cautions on changes of general register settings
Figure 8-39 shows six correct examples and one incorrect example.
211
GRA3
GR
H'0000
Not allowed
BR
GR
Figure 8-39 Changing a General Register Setting by Buffer Transfer (Example 1)
— Buffer transfer at transition from up-counting to down-counting
If the general register value is in the range from GRA3 – T + 1 to GRA3, do not transfer a
buffer register value outside this range. Conversely, if the general register value is outside
this range, do not transfer a value within this range. See figure 8-40.
GRA3 + 1
GRA3
Illegal changes
GRA3 – T + 1
GRA3 – T
TCNT3
TCNT4
Figure 8-40 Changing a General Register Setting by Buffer Transfer (Caution 1)
212
— Buffer transfer at transition from down-counting to up-counting
If the general register value is in the range from H'0000 to T – 1, do not transfer a buffer
register value outside this range. Conversely, when a general register value is outside this
range, do not transfer a value within this range. See figure 8-41.
TCNT3
TCNT4
T
T–1
Illegal changes
H'0000
H'FFFF
Figure 8-41 Changing a General Register Setting by Buffer Transfer (Caution 2)
213
— General register settings outside the counting range (H'0000 to GRA3)
Waveforms with a duty cycle of 0% or 100% can be output by setting a general register to
a value outside the counting range. When a buffer register is set to a value outside the
counting range, then later restored to a value within the counting range, the counting
direction (up or down) must be the same both times. See figure 8-42.
GRA3
GR
H'0000
0% duty cycle
100% duty cycle
Output pin
Output pin
BR
GR
Write during down-counting
Write during up-counting
Figure 8-42 Changing a General Register Setting by Buffer Transfer (Example 2)
Settings can be made in this way by detecting GRA3 compare match or TCNT4
underflow before writing to the buffer register.
214
8.4.7 Phase Counting Mode
In phase counting mode the phase difference between two external clock inputs (at the TCLKA
and TCLKB pins) is detected, and TCNT2 counts up or down accordingly.
In phase counting mode, the TCLKA and TCLKB pins automatically function as external clock
input pins and TCNT2 becomes an up/down-counter, regardless of the settings of bits TPSC2 to
TPSC0, CKEG1, and CKEG0 in TCR2. Settings of bits CCLR1, CCLR0 in TCR2, and settings in
TIOR2, TIER2, TSR2, GRA2, and GRB2 are valid. The input capture and output compare
functions can be used, and interrupts can be generated.
Phase counting is available only in channel 2.
Sample Setup Procedure for Phase Counting Mode: Figure 8-43 shows a sample procedure for
setting up phase counting mode.
Phase counting mode
Select phase counting mode
1
Select flag setting condition
2
Start counter
3
1. Set the MDF bit in TMDR to 1 to select
phase counting mode.
2. Select the flag setting condition with
the FDIR bit in TMDR.
3. Set the STR2 bit to 1 in TSTR to start
the timer counter.
Phase counting mode
Figure 8-43 Setup Procedure for Phase Counting Mode (Example)
215
Example of Phase Counting Mode: Figure 8-44 shows an example of operations in phase
counting mode. Table 8-9 lists the up-counting and down-counting conditions for TCNT2.
In phase counting mode both the rising and falling edges of TCLKA and TCLKB are counted.
The phase difference between TCLKA and TCLKB must be at least 1.5 states, the phase overlap
must also be at least 1.5 states, and the pulse width must be at least 2.5 states. See figure 8-45.
TCNT2 value
Counting up
Counting down
Time
TCLKB
TCLKA
Figure 8-44 Operation in Phase Counting Mode (Example)
Table 8-9 Up/Down Counting Conditions
Counting Direction
Up-Counting
TCLKB
Down-Counting
High
TCLKA
Low
Phase
difference
Low
High
Phase
difference
High
Low
Low
Pulse width
High
Pulse width
TCLKA
TCLKB
Overlap
Overlap
Phase difference and overlap: at least 1.5 states
Pulse width:
at least 2.5 states
Figure 8-45 Phase Difference, Overlap, and Pulse Width in Phase Counting Mode
216
8.4.8 Buffering
Buffering operates differently depending on whether a general register is an output compare
register or an input capture register, with further differences in reset-synchronized PWM mode
and complementary PWM mode. Buffering is available only in channels 3 and 4. Buffering
operations under the conditions mentioned above are described next.
•
General register used for output compare
The buffer register value is transferred to the general register at compare match. See
figure 8-46.
Compare match signal
BR
GR
Comparator
TCNT
Figure 8-46 Compare Match Buffering
•
General register used for input capture
The TCNT value is transferred to the general register at input capture. The previous general
register value is transferred to the buffer register.
See figure 8-47.
Input capture signal
BR
GR
Figure 8-47 Input Capture Buffering
217
TCNT
•
Complementary PWM mode
The buffer register value is transferred to the general register when TCNT3 and TCNT4
change counting direction. This occurs at the following two times:
— When TCNT3 matches GRA3
— When TCNT4 underflows
•
Reset-synchronized PWM mode
The buffer register value is transferred to the general register at compare match A3.
Sample Buffering Setup Procedure: Figure 8-48 shows a sample buffering setup procedure.
Buffering
Select general register functions
1
Set buffer bits
2
Start counters
3
1. Set TIOR to select the output compare or input
capture function of the general registers.
2. Set bits BFA3, BFA4, BFB3, and BFB4 in TFCR
to select buffering of the required general registers.
3. Set the STR bits to 1 in TSTR to start the timer
counters.
Buffered operation
Figure 8-48 Buffering Setup Procedure (Example)
218
Examples of Buffering: Figure 8-49 shows an example in which GRA is set to function as an
output compare register buffered by BRA, TCNT is set to operate as a periodic counter cleared by
GRB compare match, and TIOCA and TIOCB are set to toggle at compare match A and B.
Because of the buffer setting, when TIOCA toggles at compare match A, the BRA value is
simultaneously transferred to GRA. This operation is repeated each time compare match A occurs.
Figure 8-50 shows the transfer timing.
TCNT value
Counter cleared by compare match B
GRB
H'0250
H'0200
H'0100
H'0000
Time
BRA
H'0200
GRA
H'0250
H'0200
H'0100
H'0200
H'0100
H'0200
TIOCB
Toggle
output
TIOCA
Toggle
output
Compare match A
Figure 8-49 Register Buffering (Example 1: Buffering of Output Compare Register)
219
ø
n
TCNT
n+1
Compare
match signal
Buffer transfer
signal
N
BR
GR
n
N
Figure 8-50 Compare Match and Buffer Transfer Timing (Example)
220
Figure 8-51 shows an example in which GRA is set to function as an input capture register
buffered by BRA, and TCNT is cleared by input capture B. The falling edge is selected as the
input capture edge at TIOCB. Both edges are selected as input capture edges at TIOCA. Because
of the buffer setting, when the TCNT value is captured into GRA at input capture A, the previous
GRA value is simultaneously transferred to BRA. Figure 8-52 shows the transfer timing.
TCNT value
Counter cleared by
input capture B
H'0180
H'0160
H'0005
H'0000
Time
TIOCB
TOICA
GRA
H'0005
H'0160
H'0160
H'0005
BRA
GRB
H'0180
Input capture A
Figure 8-51 Register Buffering (Example 2: Buffering of Input Capture Register)
221
ø
TIOC pin
Input capture
signal
TCNT
n
n+1
N
N+1
GR
M
n
n
N
BR
m
M
M
n
Figure 8-52 Input Capture and Buffer Transfer Timing (Example)
222
Figure 8-53 shows an example in which GRB3 is buffered by BRB3 in complementary PWM
mode. Buffering is used to set GRB3 to a higher value than GRA3, generating a PWM waveform
with 0% duty cycle. The BRB3 value is transferred to GRB3 when TCNT3 matches GRA3, and
when TCNT4 underflows.
TCNT3 and
TCNT4 values
TCNT3
H'1FFF
GRA3
GRB3
TCNT4
H'0999
H'0000
BRB3
GRB3
Time
H'1FFF
H'0999
H'0999
H'0999
H'1FFF
H'0999
H'1FFF
H'0999
TIOCA3
TIOCB3
Figure 8-53 Register Buffering (Example 4: Buffering in Complementary PWM Mode)
223
8.4.9 ITU Output Timing
The ITU outputs from channels 3 and 4 can be disabled by bit settings in TOER or by an external
trigger, or inverted by bit settings in TOCR.
Timing of Enabling and Disabling of ITU Output by TOER: In this example an ITU output is
disabled by clearing a master enable bit to 0 in TOER. An arbitrary value can be output by
appropriate settings of the data register (DR) and data direction register (DDR) of the
corresponding input/output port. Figure 8-54 illustrates the timing of the enabling and disabling of
ITU output by TOER.
T1
T2
T3
ø
Address
TOER address
TOER
ITU output pin
Timer output
ITU output
I/O port
Generic input/output
Figure 8-54 Timing of Disabling of ITU Output by Writing to TOER (Example)
224
Timing of Disabling of ITU Output by External Trigger: If the XTGD bit is cleared to 0 in
TOCR in reset-synchronized PWM mode or complementary PWM mode, when an input capture
A signal occurs in channel 1, the master enable bits are cleared to 0 in TOER, disabling ITU
output. Figure 8-55 shows the timing.
ø
TIOCA1 pin
Input capture
signal
N
TOER
ITU output
pins
H'C0
N
ITU output
I/O port
Generic
input/output
ITU output
ITU output
ITU output
H'C0
I/O port
Generic
input/output
N: Arbitrary setting (H'C1 to H'FF)
Figure 8-55 Timing of Disabling of ITU Output by External Trigger (Example)
Timing of Output Inversion by TOCR: The output levels in reset-synchronized PWM mode and
complementary PWM mode can be inverted by inverting the output level select bits (OLS4 and
OLS3) in TOCR. Figure 8-56 shows the timing.
T1
T2
T3
ø
Address
TOCR address
TOCR
ITU output pin
Inverted
Figure 8-56 Timing of Inverting of ITU Output Level by Writing to TOCR (Example)
225
8.5 Interrupts
The ITU has two types of interrupts: input capture/compare match interrupts, and overflow
interrupts.
8.5.1 Setting of Status Flags
Timing of Setting of IMFA and IMFB at Compare Match: IMFA and IMFB are set to 1 by a
compare match signal generated when TCNT matches a general register (GR). The compare
match signal is generated in the last state in which the values match (when TCNT is updated from
the matching count to the next count). Therefore, when TCNT matches a general register, the
compare match signal is not generated until the next timer clock input. Figure 8-57 shows the
timing of the setting of IMFA and IMFB.
ø
TCNT input
clock
TCNT
N
N+1
GR
N
Compare
match signal
IMF
IMI
Figure 8-57 Timing of Setting of IMFA and IMFB by Compare Match
226
Timing of Setting of IMFA and IMFB by Input Capture: IMFA and IMFB are set to 1 by an
input capture signal. The TCNT contents are simultaneously transferred to the corresponding
general register. Figure 8-58 shows the timing.
ø
Input capture
signal
IMF
N
TCNT
GR
N
IMI
Figure 8-58 Timing of Setting of IMFA and IMFB by Input Capture
Timing of Setting of Overflow Flag (OVF): OVF is set to 1 when TCNT overflows from H'FFFF
to H'0000 or underflows from H'0000 to H'FFFF. Figure 8-59 shows the timing.
227
ø
TCNT
H'FFFF
H'0000
Overflow
signal
OVF
OVI
Figure 8-59 Timing of Setting of OVF
8.5.2 Clearing of Status Flags
If the CPU reads a status flag while it is set to 1, then writes 0 in the status flag, the status flag is
cleared. Figure 8-60 shows the timing.
TSR write cycle
T1
T2
T3
ø
Address
TSR address
IMF, OVF
Figure 8-60 Timing of Clearing of Status Flags
228
8.5.3 Interrupt Sources
Each ITU channel can generate a compare match/input capture A interrupt, a compare match/input
capture B interrupt, and an overflow interrupt. In total there are 15 interrupt sources, all
independently vectored. An interrupt is requested when the interrupt request flag and interrupt
enable bit are both set to 1.
The priority order of the channels can be modified in interrupt priority registers A and B (IPRA
and IPRB). For details see section 5, Interrupt Controller.
Table 8-10 lists the interrupt sources.
Table 8-10 ITU Interrupt Sources
Channel
Interrupt
Source
Description
Priority*
0
IMIA0
Compare match/input capture A0
High
IMIB0
Compare match/input capture B0
OVI0
Overflow 0
IMIA1
Compare match/input capture A1
IMIB1
Compare match/input capture B1
OVI1
Overflow 1
IMIA2
Compare match/input capture A2
IMIB2
Compare match/input capture B2
OVI2
Overflow 2
IMIA3
Compare match/input capture A3
IMIB3
Compare match/input capture B3
OVI3
Overflow 3
IMIA4
Compare match/input capture A4
IMIB4
Compare match/input capture B4
OVI4
Overflow 4
1
2
3
4
Low
Note: * The priority immediately after a reset is indicated. Inter-channel priorities can be changed
by settings in IPRA and IPRB.
229
8.6 Usage Notes
This section describes contention and other matters requiring special attention during ITU
operations.
Contention between TCNT Write and Clear: If a counter clear signal occurs in the T3 state of a
TCNT write cycle, clearing of the counter takes priority and the write is not performed. See
figure 8-61.
TCNT write cycle
T2
T1
T3
ø
Address
TCNT address
Internal write signal
Counter clear signal
TCNT
N
H'0000
Figure 8-61 Contention between TCNT Write and Clear
230
Contention between TCNT Word Write and Increment: If an increment pulse occurs in the T3
state of a TCNT word write cycle, writing takes priority and TCNT is not incremented. See
figure 8-62.
TCNT word write cycle
T1
T2
T3
ø
Address
TCNT address
Internal write signal
TCNT input clock
TCNT
N
M
TCNT write data
Figure 8-62 Contention between TCNT Word Write and Increment
231
Contention between TCNT Byte Write and Increment: If an increment pulse occurs in the T2
or T3 state of a TCNT byte write cycle, writing takes priority and TCNT is not incremented. The
TCNT byte that was not written retains its previous value. See figure 8-63, which shows an
increment pulse occurring in the T2 state of a byte write to TCNTH.
TCNTH byte write cycle
T2
T1
T3
ø
TCNTH address
Address
Internal write signal
TCNT input clock
TCNTH
N
M
TCNTH write data
TCNTL
X
X+1
X
Figure 8-63 Contention between TCNT Byte Write and Increment
232
Contention between General Register Write and Compare Match: If a compare match occurs
in the T3 state of a general register write cycle, writing takes priority and the compare match
signal is inhibited. See figure 8-64.
General register write cycle
T2
T1
T3
ø
GR address
Address
Internal write signal
TCNT
N
GR
N
N+1
M
General register write data
Compare match signal
Inhibited
Figure 8-64 Contention between General Register Write and Compare Match
233
Contention between TCNT Write and Overflow or Underflow: If an overflow occurs in the T3
state of a TCNT write cycle, writing takes priority and the counter is not incremented. OVF is
set to 1.The same holds for underflow. See figure 8-65.
TCNT write cycle
T1
T2
T3
ø
Address
TCNT address
Internal write signal
TCNT input clock
Overflow signal
TCNT
H'FFFF
M
TCNT write data
OVF
Figure 8-65 Contention between TCNT Write and Overflow
234
Contention between General Register Read and Input Capture: If an input capture signal
occurs during the T3 state of a general register read cycle, the value before input capture is read.
See figure 8-66.
General register read cycle
T1
T2
T3
ø
GR address
Address
Internal read signal
Input capture signal
GR
X
Internal data bus
M
X
Figure 8-66 Contention between General Register Read and Input Capture
235
Contention between Counter Clearing by Input Capture and Counter Increment: If an input
capture signal and counter increment signal occur simultaneously, the counter is cleared according
to the input capture signal. The counter is not incremented by the increment signal. The value
before the counter is cleared is transferred to the general register. See figure 8-67.
ø
Input capture signal
Counter clear signal
TCNT input clock
N
TCNT
GR
H'0000
N
Figure 8-67 Contention between Counter Clearing by Input Capture and
Counter Increment
236
Contention between General Register Write and Input Capture: If an input capture signal
occurs in the T3 state of a general register write cycle, input capture takes priority and the write to
the general register is not performed. See figure 8-68.
General register write cycle
T1
T2
T3
ø
Address
GR address
Internal write signal
Input capture signal
M
TCNT
GR
M
Figure 8-68 Contention between General Register Write and Input Capture
Note on Waveform Period Setting: When a counter is cleared by compare match, the counter is
cleared in the last state at which the TCNT value matches the general register value, at the time
when this value would normally be updated to the next count. The actual counter frequency is
therefore given by the following formula:
f=
ø
(N + 1)
(f: counter frequency. ø: system clock frequency. N: value set in general register.)
237
Contention between Buffer Register Write and Input Capture: If a buffer register is used for
input capture buffering and an input capture signal occurs in the T3 state of a write cycle, input
capture takes priority and the write to the buffer register is not performed.
See figure 8-69.
Buffer register write cycle
T1
T2
T3
ø
Address
BR address
Internal write signal
Input capture signal
GR
N
X
TCNT value
BR
M
N
Figure 8-69 Contention between Buffer Register Write and Input Capture
238
Note on Synchronous Preset: When channels are synchronized, if a TCNT value is modified by
byte write access, all 16 bits of all synchronized counters assume the same value as the counter
that was addressed.
(Example) When channels 2 and 3 are synchronized
• Byte write to channel 2 or byte write to channel 3
TCNT2
W
X
TCNT3
Y
Z
Upper byte Lower byte
Write A to upper byte
of channel 2
TCNT2
A
X
TCNT3
A
X
Upper byte Lower byte
Write A to lower byte
of channel 3
TCNT2
Y
A
TCNT3
Y
A
Upper byte Lower byte
• Word write to channel 2 or word write to channel 3
TCNT2
W
X
TCNT3
Y
Z
Write AB word to
channel 2 or 3
Upper byte Lower byte
TCNT2
A
B
TCNT3
A
B
Upper byte Lower byte
Note on Setup of Reset-Synchronized PWM Mode and Complementary PWM Mode: When
setting bits CMD1 and CMD0 in TFCR, take the following precautions:
•
Write to bits CMD1 and CMD0 only when TCNT3 and TCNT4 are stopped.
•
Do not switch directly between reset-synchronized PWM mode and complementary PWM
mode. First switch to normal mode (by clearing bit CMD1 to 0), then select resetsynchronized PWM mode or complementary PWM mode.
239
—
—
—
—
—
—
—
o
o
o
o
o
o
SYNC0 = 1 —
Output compare A
Output compare B
Input capture A
Input capture B
Counter By compare
clearing match/input
capture A
By compare
match/input
capture B
Synchronous
clear
—
—
—
—
o
—
o
o
PWM0 = 0 —
PWM0 = 0 —
o
PWM0 = 0 —
PWM0 = 1 —
o
TFCR
TOCR
Register Settings
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Master
Enable
TOER
o*
o
IOB
o
o
o
o
o
o
o
Clear
Select
o
o
o
TCR0
o
o
o
o
o
o
Clock
Select
CCLR1 = 1 o
CCLR0 = 1
CCLR1 = 1 o
CCLR0 = 0
CCLR1 = 0 o
CCLR0 = 1
IOB2 = 1
o
Other bits
unrestricted
o
IOB2 = 0
o
Other bits
unrestricted
IOA2 = 1
o
Other bits
unrestricted
o
IOA2 = 0
o
Other bits
unrestricted
—
o
IOA
TIOR0
240
Note: * The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
—
—
—
—
—
—
—
—
—
ResetComple- SynchroOutput
mentary nized
BufferLevel
PWM
PWM
ing
XTGD Select
Legend: o Setting available (valid). — Setting does not affect this mode.
—
—
—
—
—
—
—
—
—
SYNC0 = 1 —
o
Synchronous preset
PWM mode
FDIR PWM
Synchronization
Operating Mode
MDF
TMDR
TSNC
Table 8-11 (a) ITU Operating Modes (Channel 0)
ITU Operating Modes
—
—
—
—
—
—
—
o
o
o
o
o
o
SYNC1 = 1 —
Output compare A
Output compare B
Input capture A
Input capture B
Counter By compare
clearing match/input
capture A
By compare
match/input
capture B
Synchronous
clear
—
—
—
—
o
—
o
o
PWM1 = 0 —
PWM1 = 0 —
o
PWM1 = 0 —
PWM1 = 1 —
o
TOCR
Register Settings
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
o*2
—
—
—
—
—
—
—
—
—
—
—
—
—
ResetComple- SynchroOutput
mentary nized
BufferLevel
PWM
PWM
ing
XTGD Select
TFCR
—
—
—
—
—
—
—
—
—
Master
Enable
TOER
o*1
o
IOB
o
o
o
o
o
o
o
Clear
Select
o
o
o
TCR1
o
o
o
o
o
o
Clock
Select
CCLR1 = 1 o
CCLR0 = 1
CCLR1 = 1 o
CCLR0 = 0
CCLR1 = 0 o
CCLR0 = 1
IOB2 = 1
o
Other bits
unrestricted
o
IOB2 = 0
o
Other bits
unrestricted
IOA2 = 1
o
Other bits
unrestricted
o
IOA2 = 0
o
Other bits
unrestricted
—
o
IOA
TIOR1
241
Legend: o Setting available (valid). — Setting does not affect this mode.
Notes: 1. The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
2. Valid only when channels 3 and 4 are operating in complementary PWM mode or reset-synchronized PWM mode.
—
—
—
—
—
—
—
—
—
SYNC1 = 1 —
o
Synchronous preset
PWM mode
FDIR PWM
Synchronization
Operating Mode
MDF
TMDR
TSNC
Table 8-11 (b) ITU Operating Modes (Channel 1)
—
o
—
—
o
o
o
o
o
o
o
SYNC2 = 1 o
Output compare B
Input capture A
Input capture B
Counter By compare
clearing match/input
capture A
By compare
match/input
capture B
Synchronous
clear
MDF = 1 o
—
—
—
—
—
—
o
o
o
o
—
—
—
—
PWM2 = 0 —
PWM2 = 0 —
o
PWM2 = 0 —
PWM2 = 1 —
o
TOCR
Register Settings
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ResetComple- SynchroOutput
mentary nized
BufferLevel
PWM
PWM
ing
XTGD Select
TFCR
—
—
—
—
—
—
—
—
—
—
Master
Enable
TOER
o*
o
IOB
o
o
o
o
o
o
o
o
Clear
Select
o
o
o
o
TCR2
o
o
o
o
o
o
Clock
Select
o
—
CCLR1 = 1 o
CCLR0 = 1
CCLR1 = 1 o
CCLR0 = 0
CCLR1 = 0 o
CCLR0 = 1
IOB2 = 1
o
Other bits
unrestricted
o
IOB2 = 0
o
Other bits
unrestricted
IOA2 = 1
o
Other bits
unrestricted
o
IOA2 = 0
o
Other bits
unrestricted
—
o
IOA
TIOR2
242
Legend: o Setting available (valid). — Setting does not affect this mode.
Note: * The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
o
—
o
o
Output compare A
Phase counting
mode
—
o
—
—
SYNC2 = 1 o
o
Synchronous preset
PWM mode
FDIR PWM
Synchronization
Operating Mode
MDF
TMDR
TSNC
Table 8-11 (c) ITU Operating Modes (Channel 2)
—
—
—
—
—
—
—
—
—
—
—
—
o
o
o
o
SYNC3 = 1 —
—
o
o*3
o
o
o
Output compare B
Input capture A
Input capture B
Counter
clearing
—
—
—
—
—
o*3
PWM
o
CMD1 = 0
o
o
—
—
o
o
o
CMD1 = 0
CMD1 = 0
CMD1 = 0
o
o
Illegal setting:
CMD1 = 1
CMD0 = 0
CMD1 = 1
CMD0 = 0
CMD1 = 1
CMD0 = 1
o
o
CMD1 = 1
CMD0 = 0
CMD1 = 1
CMD0 = 1
o
Illegal setting: o*4
CMD1 = 1
CMD0 = 0
CMD1 = 0
CMD1 = 0
PWM3 = 0 CMD1 = 0
PWM3 = 0 CMD1 = 0
o
PWM3 = 1 CMD1 = 0
PWM3 = 0 CMD1 = 0
Complementary
PWM
o*6
o*6
—
—
—
—
—
—
BFA3 = 1 —
Other bits
unrestricted
BFB3 = 1 —
Other bits
unrestricted
o
o
o
o
o
o
o
o
—
—
o
o
—
—
—
—
—
—
Register Settings
TFCR
TOCR
ResetOutput
SynchroLevel
nized PWM Buffering XTGD Select
o
o
—
—
CMD1 = 0 o
—
—
CMD1 = 0 o
—
—
o*1
o*1
o
o
o*1
o*1
o*1
EA3 ignored
Other bits
unrestricted
EA3 ignored
Other bits
unrestricted
o
o
o
—
—
o
o
o
—
o*2
IOA2 = 0
o
Other bits
unrestricted
o
IOB2 = 0
Other bits
unrestricted
IOA2 = 1
o
Other bits
unrestricted
o
IOA2 = 1
Other bits
unrestricted
o
o
o
o*1
o
o
—
—
o
o
o
o
IOA
IOB
TIOR3
Master
Enable
TOER
o
o
o
o
o
o
Clock
Select
o
o
o
o
CCLR1 = 0 o*5
CCLR0 = 0
CCLR1 = 0 o
CCLR0 = 1
CCLR1 = 1 o
CCLR0 = 1
CCLR1 = 1 o
CCLR0 = 0
CCLR1 = 0 o
CCLR0 = 1
o
o
o
o
o
o
Clear
Select
TCR3
243
Legend: o Setting available (valid). — Setting does not affect this mode.
Notes: 1. Master enable bit settings are valid only during waveform output.
2. The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
3. Do not set both channels 3 and 4 for synchronous operation when complementary PWM mode is selected.
4. The counter cannot be cleared by input capture A when reset-synchronized PWM mode is selected.
5. In complementary PWM mode, select the same clock source for channels 3 and 4.
6. Use the input capture A function in channel 1.
Buffering
(BRB)
By compare
match/input
capture A
By compare
match/input
capture B
Synchronous
clear
Complementary
PWM mode
Reset-synchronized
PWM mode
Buffering
(BRA)
FDIR
—
—
—
Synchronization
MDF
SYNC3 = 1 —
o
—
o
—
Operating Mode
Synchronous preset
PWM mode
Output compare A
—
TMDR
TSNC
Table 8-11 (d) ITU Operating Modes (Channel 3)
—
—
—
—
—
—
—
—
—
—
—
—
o
o
o
o
SYNC4 = 1 —
—
o
o*3
o
o
o
Output compare B
Input capture A
Input capture B
Counter
clearing
—
—
—
—
—
o*3
PWM
o
CMD1 = 0
o
o
—
—
o
o
o
o
o
Illegal setting:
CMD1 = 1
CMD0 = 0
Illegal setting:
CMD1 = 1
CMD0 = 0
Illegal setting:
CMD1 = 1
CMD0 = 0
CMD1 = 1
CMD0 = 0
CMD1 = 1
CMD0 = 1
PWM4 = 0 CMD1 = 0
PWM4 = 0 CMD1 = 0
o
PWM4 = 1 CMD1 = 0
PWM4 = 0 CMD1 = 0
Complementary
PWM
o
o
CMD1 = 1
CMD0 = 0
CMD1 = 1
CMD0 = 1
o*4
o*4
o*4
CMD1 = 0
CMD1 = 0
CMD1 = 0
o
o
—
—
—
—
—
—
BFA4 = 1 —
Other bits
unrestricted
BFB4 = 1 —
Other bits
unrestricted
o
o
o
o
o
o
o
o
—
—
o
o
—
—
—
—
—
—
Register Settings
TFCR
TOCR
ResetOutput
SynchroLevel
nized PWM Buffering XTGD Select
o
o
—
—
CMD1 = 0 o
—
—
CMD1 = 0 o
—
—
o*1
o*1
o
o
o*1
o*1
o*1
EA4 ignored
Other bits
unrestricted
EB4 ignored
Other bits
unrestricted
o
o
o
—
—
o
o
o
—
o*2
IOA2 = 0
o
Other bits
unrestricted
o
IOB2 = 0
Other bits
unrestricted
IOA2 = 1
o
Other bits
unrestricted
o
IOB2 = 1
Other bits
unrestricted
o
o
o
o*1
o
o
—
—
o
o
o
o
IOA
IOB
TIOR4
Master
Enable
TOER
o
o
o
o
o
o
Clock
Select
o
o
o*6
o
o
o*6
CCLR1 = 0 o*5
CCLR0 = 0
CCLR1 = 1 o
CCLR0 = 1
CCLR1 = 1 o
CCLR0 = 0
CCLR1 = 0 o
CCLR0 = 1
o
o
o
o
o
o
Clear
Select
TCR4
244
Legend: o Setting available (valid). — Setting does not affect this mode.
Notes: 1. Master enable bit settings are valid only during waveform output.
2. The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
3. Do not set both channels 3 and 4 for synchronous operation when complementary PWM mode is selected.
4. When reset-synchronized PWM mode is selected, TCNT4 operates independently and the counter clearing function is available. Waveform output is not affected.
5. In complementary PWM mode, select the same clock source for channels 3 and 4.
6. TCR4 settings are valid in reset-synchronized PWM mode, but TCNT4 operates independently, without affecting waveform output.
Buffering
(BRB)
By compare
match/input
capture A
By compare
match/input
capture B
Synchronous
clear
Complementary
PWM mode
Reset-synchronized
PWM mode
Buffering
(BRA)
FDIR
—
—
—
Synchronization
MDF
SYNC4 = 1 —
o
—
o
—
Operating Mode
Synchronous preset
PWM mode
Output compare A
—
TMDR
TSNC
Table 8-11 (e) ITU Operating Modes (Channel 4)
Section 9 Watchdog Timer
9.1 Overview
The H8/3004 and H8/3005 have an on-chip watchdog timer (WDT). The WDT has two selectable
functions: it can operate as a watchdog timer to supervise system operation, or it can operate as an
interval timer. As a watchdog timer, it generates a reset signal for the H8/3004 and H8/3005 chip
if a system crash allows the timer counter (TCNT) to overflow before being rewritten. In interval
timer operation, an interval timer interrupt is requested at each TCNT overflow.
9.1.1 Features
WDT features are listed below.
•
Selection of eight counter clock sources
ø/2, ø/32, ø/64, ø/128, ø/256, ø/512, ø/2048, or ø/4096
•
Interval timer option
•
Timer counter overflow generates a reset signal or interrupt.
The reset signal is generated in watchdog timer operation. An interval timer interrupt is
generated in interval timer operation.
•
Watchdog timer reset signal resets the entire H8/3004 and H8/3005 internally, and can also be
output externally.
The reset signal generated by timer counter overflow during watchdog timer operation resets
the entire H8/3004 and H8/3005 internally. An external reset signal can be output from the
RESO pin to reset other system devices simultaneously.
245
9.1.2 Block Diagram
Figure 9-1 shows a block diagram of the WDT.
Overflow
TCNT
Interrupt
(interval timer) control
Interrupt signal
TCSR
Read/
write
control
Internal
data bus
Internal clock sources
ø/2
RSTCSR
ø/32
Reset
(internal, external)
Reset control
ø/64
Clock
Clock
selector
ø/128
ø/256
ø/512
Legend
TCNT:
Timer counter
TCSR:
Timer control/status register
RSTCSR: Reset control/status register
ø/2048
ø/4096
Figure 9-1 WDT Block Diagram
9.1.3 Pin Configuration
Table 9-1 describes the WDT output pin.
Table 9-1 WDT Pin
Name
Abbreviation
I/O
Function
Reset output
RESO
Output*
External output of the watchdog timer reset signal
Note: * Open-drain output.
246
9.1.4 Register Configuration
Table 9-2 summarizes the WDT registers.
Table 9-2 WDT Registers
Address*1
Write*2
Read
Name
Abbreviation
R/W
Initial Value
H'FFA8
H'FFA8
Timer control/status register
TCSR
R/(W)*3
H'18
H'FFA9
Timer counter
TCNT
R/W
H'00
H'FFAB
Reset control/status register
RSTCSR
R/(W)*3
H'3F
H'FFAA
Notes: 1. Lower 16 bits of the address.
2. Write word data starting at this address.
3. Only 0 can be written in bit 7, to clear the flag.
247
9.2 Register Descriptions
9.2.1 Timer Counter (TCNT)
TCNT is an 8-bit readable and writable* up-counter.
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
When the TME bit is set to 1 in TCSR, TCNT starts counting pulses generated from an internal
clock source selected by bits CKS2 to CKS0 in TCSR. When the count overflows (changes from
H'FF to H'00), the OVF bit is set to 1 in TCSR. TCNT is initialized to H'00 by a reset and when
the TME bit is cleared to 0.
Note: * TCNT is write-protected by a password. For details see section 9.2.4, Notes on Register
Access.
248
9.2.2 Timer Control/Status Register (TCSR)
TCSR is an 8-bit readable and writable*1 register. Its functions include selecting the timer mode
and clock source.
Bit
7
6
5
4
3
2
1
0
OVF
WT/IT
TME
—
—
CKS2
CKS1
CKS0
Initial value
0
0
0
1
1
0
0
0
Read/Write
R/(W)*2
R/W
R/W
—
—
R/W
R/W
R/W
Clock select
These bits select the
TCNT clock source
Reserved bits
Timer enable
Selects whether TCNT runs or halts
Timer mode select
Selects the mode
Overflow flag
Status flag indicating overflow
Bits 7 to 5 are initialized to 0 by a reset and in standby mode. Bits 2 to 0 are initialized to 0 by a
reset. In software standby mode bits 2 to 0 are not initialized, but retain their previous values.
Notes: 1. TCSR is write-protected by a password. For details see section 9.2.4, Notes on Register
Access.
2. Only 0 can be written, to clear the flag.
249
Bit 7—Overflow Flag (OVF): This status flag indicates that the timer counter has overflowed
from H'FF to H'00.
Bit 7
OVF
0
1
Description
[Clearing condition]
Cleared by reading OVF when OVF = 1, then writing 0 in OVF
(Initial value)
[Setting condition]
Set when TCNT changes from H'FF to H'00
Bit 6—Timer Mode Select (WT/IT): Selects whether to use the WDT as a watchdog timer or
interval timer. If used as an interval timer, the WDT generates an interval timer interrupt request
when TCNT overflows. If used as a watchdog timer, the WDT generates a reset signal when
TCNT overflows.
Bit 6
WT/IT
Description
0
Interval timer: requests interval timer interrupts
1
Watchdog timer: generates a reset signal
(Initial value)
Bit 5—Timer Enable (TME): Selects whether TCNT runs or is halted.
Bit 5
TME
Description
0
TCNT is initialized to H'00 and halted
1
TCNT is counting
(Initial value)
Bits 4 and 3—Reserved: Read-only bits, always read as 1.
250
Bits 2 to 0—Clock Select 2 to 0 (CKS2/1/0): These bits select one of eight internal clock
sources, obtained by prescaling the system clock (ø), for input to TCNT.
Bit 2
CKS2
Bit 1
CKS1
Bit 0
CKS0
Description
0
0
0
ø/2
1
ø/32
0
ø/64
1
ø/128
0
ø/256
1
ø/512
0
ø/2048
1
ø/4096
1
1
0
1
(Initial value)
9.2.3 Reset Control/Status Register (RSTCSR)
RSTCSR is an 8-bit readable and writable*1 register that indicates when a reset signal has been
generated by watchdog timer overflow, and controls external output of the reset signal.
Bit
7
6
5
4
3
2
1
0
WRST
RSTOE
—
—
—
—
—
—
Initial value
0
0
1
1
1
1
1
1
Read/Write
R/(W)*2
R/W
—
—
—
—
—
—
Reserved bits
Reset output enable
Enables or disables external output of the reset signal
Watchdog timer reset
Indicates that a reset signal has been generated
Bits 7 and 6 are initialized by input of a reset signal at the RES pin. They are not initialized by
reset signals generated by watchdog timer overflow.
Notes: 1. RSTCSR is write-protected by a password. For details see section 9.2.4, Notes on
Register Access.
2. Only 0 can be written in bit 7, to clear the flag.
251
Bit 7—Watchdog Timer Reset (WRST): During watchdog timer operation, this bit indicates that
TCNT has overflowed and generated a reset signal. This reset signal resets the entire H8/3004 or
H8/3005 chip. If bit RSTOE is set to 1, this reset signal is also output (low) at the RESO pin to
initialize external system devices.
Bit 7
WRST
0
1
Description
[Clearing condition]
Cleared to 0 by reset signal input at RES pin, or by writing 0
(Initial value)
[Setting condition]
Set when TCNT overflow generates a reset signal during watchdog timer operation
Bit 6—Reset Output Enable (RSTOE): Enables or disables external output at the RESO pin of
the reset signal generated if TCNT overflows during watchdog timer operation.
Bit 6
RSTOE
Description
0
Reset signal is not output externally
1
Reset signal is output externally
(Initial value)
Bits 5 to 0—Reserved: Read-only bits, always read as 1.
252
9.2.4 Notes on Register Access
The watchdog timer’s TCNT, TCSR, and RSTCSR registers differ from other registers in being
more difficult to write. The procedures for writing and reading these registers are given below.
Writing to TCNT and TCSR: These registers must be written by a word transfer instruction.
They cannot be written by byte instructions. Figure 9-2 shows the format of data written to TCNT
and TCSR. TCNT and TCSR both have the same write address. The write data must be contained
in the lower byte of the written word. The upper byte must contain H'5A (password for TCNT) or
H'A5 (password for TCSR). This transfers the write data from the lower byte to TCNT or TCSR.
15
TCNT write
Address
H'FFA8*
8 7
H'5A
15
TCSR write
Address
H'FFA8*
0
Write data
8 7
H'A5
0
Write data
Note: * Lower 16 bits of the address.
Figure 9-2 Format of Data Written to TCNT and TCSR
253
Writing to RSTCSR: RSTCSR must be written by a word transfer instruction. It cannot be
written by byte transfer instructions. Figure 9-3 shows the format of data written to RSTCSR. To
write 0 in the WRST bit, the write data must have H'A5 in the upper byte and H'00 in the lower
byte. The H'00 in the lower byte clears the WRST bit in RSTCSR to 0. To write to the RSTOE bit,
the upper byte must contain H'5A and the lower byte must contain the write data. Writing this
word transfers a write data value into the RSTOE bit.
Writing 0 in WRST bit
Address
H'FFAA*
Writing to RSTOE bit
Address
15
8 7
H'A5
15
H'FFAA*
0
H'00
8 7
H'5A
0
Write data
Note: * Lower 16 bits of the address.
Figure 9-3 Format of Data Written to RSTCSR
Reading TCNT, TCSR, and RSTCSR: These registers are read like other registers. Byte access
instructions can be used. The read addresses are H'FFA8 for TCSR, H'FFA9 for TCNT, and
H'FFAB for RSTCSR, as listed in table 9-3.
Table 9-3 Read Addresses of TCNT, TCSR, and RSTCSR
Address*
Register
H'FFA8
TCSR
H'FFA9
TCNT
H'FFAB
RSTCSR
Note: * Lower 16 bits of the address.
254
9.3 Operation
Operations when the WDT is used as a watchdog timer and as an interval timer are described
below.
9.3.1 Watchdog Timer Operation
Figure 9-4 illustrates watchdog timer operation. To use the WDT as a watchdog timer, set the
WT/IT and TME bits to 1 in TCSR. Software must prevent TCNT overflow by rewriting the
TCNT value (normally by writing H'00) before overflow occurs. If TCNT fails to be rewritten and
overflows due to a system crash etc., the H8/3004 and H8/3005 are internally reset for a duration
of 518 states.
The watchdog reset signal can be externally output from the RESO pin to reset external system
devices. The reset signal is output externally for 132 states. External output can be enabled or
disabled by the RSTOE bit in RSTCSR.
A watchdog reset has the same vector as a reset generated by input at the RES pin. Software can
distinguish a RES reset from a watchdog reset by checking the WRST bit in RSTCSR.
If a RES reset and a watchdog reset occur simultaneously, the RES reset takes priority.
WDT overflow
H'FF
TME set to 1
TCNT count
value
H'00
OVF = 1
Start
Internal
reset signal
H'00 written
in TCNT
Reset
518 states
RESO
132 states
Figure 9-4 Watchdog Timer Operation
255
H'00 written
in TCNT
9.3.2 Interval Timer Operation
Figure 9-5 illustrates interval timer operation. To use the WDT as an interval timer, clear bit
WT/IT to 0 and set bit TME to 1 in TCSR. An interval timer interrupt request is generated at each
TCNT overflow. This function can be used to generate interval timer interrupts at regular intervals.
H'FF
TCNT
count value
Time t
H'00
WT/ IT = 0
TME = 1
Interval
timer
interrupt
Interval
timer
interrupt
Interval
timer
interrupt
Interval
timer
interrupt
Figure 9-5 Interval Timer Operation
256
9.3.3 Timing of Setting of Overflow Flag (OVF)
Figure 9-6 shows the timing of setting of the OVF flag in TCSR. The OVF flag is set to 1 when
TCNT overflows. At the same time, a reset signal is generated in watchdog timer operation, or an
interval timer interrupt is generated in interval timer operation.
ø
TCNT
H'FF
H'00
Overflow signal
OVF
Figure 9-6 Timing of Setting of OVF
257
9.3.4 Timing of Setting of Watchdog Timer Reset Bit (WRST)
The WRST bit in RSTCSR is valid when bits WT/IT and TME are both set to 1 in TCSR.
Figure 9-7 shows the timing of setting of WRST and the internal reset timing. The WRST bit is
set to 1 when TCNT overflows and OVF is set to 1. At the same time an internal reset signal is
generated for the entire H8/3004 and H8/3005 chip. This internal reset signal clears OVF to 0, but
the WRST bit remains set to 1. The reset routine must therefore clear the WRST bit.
ø
H'FF
TCNT
H'00
Overflow signal
OVF
WDT internal
reset
WRST
Figure 9-7 Timing of Setting of WRST Bit and Internal Reset
258
9.4 Interrupts
During interval timer operation, an overflow generates an interval timer interrupt (WOVI). The
interval timer interrupt is requested whenever the OVF bit is set to 1 in TCSR.
9.5 Usage Notes
Contention between TCNT Write and Increment: If a timer counter clock pulse is generated
during the T3 state of a write cycle to TCNT, the write takes priority and the timer count is not
incremented. See figure 9-8.
Write cycle: CPU writes to TCNT
T1
T2
T3
ø
TCNT
Internal write
signal
TCNT input
clock
TCNT
N
M
Counter write data
Figure 9-8 Contention between TCNT Write and Increment
Changing CKS2 to CKS0 Values: Halt TCNT by clearing the TME bit to 0 in TCSR before
changing the values of bits CKS2 to CKS0.
259
260
Section 10 Serial Communication Interface
10.1 Overview
The H8/3004 and H8/3005 have a serial communication interface (SCI). The SCI can
communicate in asynchronous mode or synchronous mode, and has a multiprocessor
communication function for serial communication among two or more processors.
10.1.1 Features
SCI features are listed below.
•
Selection of asynchronous or synchronous mode for serial communication
a.
Asynchronous mode
Serial data communication is synchronized one character at a time. The SCI can communicate
with a universal asynchronous receiver/transmitter (UART), asynchronous communication
interface adapter (ACIA), or other chip that employs standard asynchronous serial
communication. It can also communicate with two or more other processors using the
multiprocessor communication function. There are twelve selectable serial data
communication formats.
—
—
—
—
—
—
b.
Data length:
Stop bit length:
Parity bit:
Multiprocessor bit:
Receive error detection:
Break detection:
7 or 8 bits
1 or 2 bits
even, odd, or none
1 or 0
parity, overrun, and framing errors
by reading the RxD level directly when a framing error occurs
Synchronous mode
Serial data communication is synchronized with a clock signal. The SCI can communicate
with other chips having a synchronous communication function. There is one serial data
communication format.
— Data length:
8 bits
— Receive error detection: overrun errors
261
•
Full duplex communication
The transmitting and receiving sections are independent, so the SCI can transmit and receive
simultaneously. The transmitting and receiving sections are both double-buffered, so serial
data can be transmitted and received continuously.
•
Built-in baud rate generator with selectable bit rates
•
Selectable transmit/receive clock sources: internal clock from baud rate generator, or external
clock from the SCK pin.
•
Four types of interrupts
Transmit-data-empty, transmit-end, receive-data-full, and receive-error interrupts are
requested independently.
262
10.1.2 Block Diagram
Bus interface
Figure 10-1 shows a block diagram of the SCI.
Module data bus
RxD
RDR
TDR
RSR
TSR
SSR
SCR
SMR
BRR
Baud rate
generator
Transmit/
receive control
TxD
Parity generate
Parity check
SCK
ø
ø/4
ø/16
ø/64
Clock
External clock
TEI
TXI
RXI
ERI
Legend
RSR: Receive shift register
RDR: Receive data register
TSR: Transmit shift register
TDR: Transmit data register
SMR: Serial mode register
SCR: Serial control register
SSR: Serial status register
BRR: Bit rate register
Figure 10-1 SCI Block Diagram
263
Internal
data bus
10.1.3 Input/Output Pins
The SCI has serial pins as listed in table 10-1.
Table 10-1 SCI Pins
Name
Abbreviation
I/O
Function
Serial clock pin
SCK
Input/output
SCI clock input/output
Receive data pin
RxD
Input
SCI receive data input
Transmit data pin
TxD
Output
SCI transmit data output
10.1.4 Register Configuration
The SCI has internal registers as listed in table 10-2. These registers select asynchronous or
synchronous mode, specify the data format and bit rate, and control the transmitter and receiver
sections.
Table 10-2 Registers
Address*1
Name
Abbreviation
R/W
Initial Value
H'FFB0
Serial mode register
SMR
R/W
H'00
H'FFB1
Bit rate register
BRR
R/W
H'FF
H'FFB2
Serial control register
SCR
R/W
H'00
H'FFB3
Transmit data register
TDR
R/W
H'FF
H'FFB4
Serial status register
SSR
R/(W)*2
H'84
H'FFB5
Receive data register
RDR
R
H'00
Notes: 1. Lower 16 bits of the address.
2. Only 0 can be written, to clear flags.
264
10.2 Register Descriptions
10.2.1 Receive Shift Register (RSR)
RSR is the register that receives serial data.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
Initial value
Read/Write
The SCI loads serial data input at the RxD pin into RSR in the order received, LSB (bit 0) first,
thereby converting the data to parallel data. When 1 byte has been received, it is automatically
transferred to RDR. The CPU cannot read or write RSR directly.
10.2.2 Receive Data Register (RDR)
RDR is the register that stores received serial data.
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
When the SCI finishes receiving 1 byte of serial data, it transfers the received data from RSR into
RDR for storage. RSR is then ready to receive the next data. This double buffering allows data to
be received continuously.
RDR is a read-only register. Its contents cannot be modified by the CPU. RDR is initialized to
H'00 by a reset and in standby mode.
265
10.2.3 Transmit Shift Register (TSR)
TSR is the register that transmits serial data.
Bit
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
—
Initial value
Read/Write
The SCI loads transmit data from TDR into TSR, then transmits the data serially from the TxD
pin, LSB (bit 0) first. After transmitting one data byte, the SCI automatically loads the next
transmit data from TDR into TSR and starts transmitting it. If the TDRE flag is set to 1 in SSR,
however, the SCI does not load the TDR contents into TSR. The CPU cannot read or write TSR
directly.
10.2.4 Transmit Data Register (TDR)
TDR is an 8-bit register that stores data for serial transmission.
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
When the SCI detects that TSR is empty, it moves transmit data written in TDR from TDR into
TSR and starts serial transmission. Continuous serial transmission is possible by writing the next
transmit data in TDR during serial transmission from TSR.
The CPU can always read and write TDR. TDR is initialized to H'FF by a reset and in standby
mode.
266
10.2.5 Serial Mode Register (SMR)
SMR is an 8-bit register that specifies the SCI serial communication format and selects the clock
source for the baud rate generator.
Bit
7
6
5
4
3
2
1
0
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Clock select 1/0
These bits select the
baud rate generator’s
clock source
Multiprocessor mode
Selects the multiprocessor
function
Stop bit length
Selects the stop bit length
Parity mode
Selects even or odd parity
Parity enable
Selects whether a parity bit is added
Character length
Selects character length in asynchronous mode
Communication mode
Selects asynchronous or synchronous mode
The CPU can always read and write SMR. SMR is initialized to H'00 by a reset and in standby
mode.
267
Bit 7—Communication Mode (C/A): Selects whether the SCI operates in asynchronous or
synchronous mode.
Bit 7
C/A
Description
0
Asynchronous mode
1
Synchronous mode
(Initial value)
Bit 6—Character Length (CHR): Selects 7-bit or 8-bit data length in asynchronous mode. In
synchronous mode the data length is 8 bits regardless of the CHR setting.
Bit 6
CHR
Description
0
8-bit data
1
7-bit data*
(Initial value)
Note: * When 7-bit data is selected, the MSB (bit 7) in TDR is not transmitted.
Bit 5—Parity Enable (PE): In asynchronous mode, this bit enables or disables the addition of a
parity bit to transmit data, and the checking of the parity bit in receive data. In synchronous mode
the parity bit is neither added nor checked, regardless of the PE setting.
Bit 5
PE
Description
0
Parity bit not added or checked
1
Parity bit added and checked*
(Initial value)
Note: * When PE is set to 1, an even or odd parity bit is added to transmit data according to the
even or odd parity mode selected by the O/E bit, and the parity bit in receive data is
checked to see that it matches the even or odd mode selected by the O/E bit.
268
Bit 4—Parity Mode (O/E): Selects even or odd parity. The O/E bit setting is valid in
asynchronous mode when the PE bit is set to 1 to enable the adding and checking of a parity bit.
The O/E setting is ignored in synchronous mode, or when parity adding and checking is disabled
in asynchronous mode.
Bit 4
O/E
Description
0
Even parity*1
1
Odd
(Initial value)
parity*2
Notes: 1. When even parity is selected, the parity bit added to transmit data makes an even
number of 1s in the transmitted character and parity bit combined. Receive data must
have an even number of 1s in the received character and parity bit combined.
2. When odd parity is selected, the parity bit added to transmit data makes an odd number
of 1s in the transmitted character and parity bit combined. Receive data must have an
odd number of 1s in the received character and parity bit combined.
Bit 3—Stop Bit Length (STOP): Selects one or two stop bits in asynchronous mode. This setting
is used only in asynchronous mode. In synchronous mode no stop bit is added, so the STOP bit
setting is ignored.
Bit 3
STOP
Description
0
One stop bit*1
1
Two stop bits*2
(Initial value)
Notes: 1. One stop bit (with value 1) is added at the end of each transmitted character.
2. Two stop bits (with value 1) are added at the end of each transmitted character.
In receiving, only the first stop bit is checked, regardless of the STOP bit setting. If the second
stop bit is 1 it is treated as a stop bit. If the second stop bit is 0 it is treated as the start bit of the
next incoming character.
269
Bit 2—Multiprocessor Mode (MP): Selects a multiprocessor format. When a multiprocessor
format is selected, parity settings made by the PE and O/E bits are ignored. The MP bit setting is
valid only in asynchronous mode. It is ignored in synchronous mode.
For further information on the multiprocessor communication function, see section 10.3.3,
Multiprocessor Communication Function.
Bit 2
MP
Description
0
Multiprocessor function disabled
1
Multiprocessor format selected
(Initial value)
Bits 1 and 0—Clock Select 1 and 0 (CKS1/0): These bits select the clock source of the on-chip
baud rate generator. Four clock sources are available: ø, ø/4, ø/16, and ø/64.
For the relationship between the clock source, bit rate register setting, and baud rate, see
section 10.2.8, Bit Rate Register.
Bit 1
CKS1
Bit 0
CKS0
Description
0
0
ø
1
ø/4
0
ø/16
1
ø/64
1
(Initial value)
270
10.2.6 Serial Control Register (SCR)
SCR enables the SCI transmitter and receiver, enables or disables serial clock output in
asynchronous mode, enables or disables interrupts, and selects the transmit/receive clock source.
Bit
7
6
5
4
3
2
1
0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Clock enable 1/0
These bits select the
SCI clock source
Transmit end interrupt enable
Enables or disables transmitend interrupts (TEI)
Multiprocessor interrupt enable
Enables or disables multiprocessor
interrupts
Receive enable
Enables or disables the receiver
Transmit enable
Enables or disables the transmitter
Receive interrupt enable
Enables or disables receive-data-full interrupts (RXI) and
receive-error interrupts (ERI)
Transmit interrupt enable
Enables or disables transmit-data-empty interrupts (TXI)
The CPU can always read and write SCR. SCR is initialized to H'00 by a reset and in standby
mode.
271
Bit 7—Transmit Interrupt Enable (TIE): Enables or disables the transmit-data-empty interrupt
(TXI) requested when the TDRE flag in SSR is set to 1 due to transfer of serial transmit data from
TDR to TSR.
Bit 7
TIE
Description
0
Transmit-data-empty interrupt request (TXI) is disabled*
1
Transmit-data-empty interrupt request (TXI) is enabled
(Initial value)
Note: * TXI interrupt requests can be cleared by reading the value 1 from the TDRE flag, then
clearing it to 0; or by clearing the TIE bit to 0.
Bit 6—Receive Interrupt Enable (RIE): Enables or disables the receive-data-full interrupt (RXI)
requested when the RDRF flag is set to 1 in SSR due to transfer of serial receive data from RSR to
RDR; also enables or disables the receive-error interrupt (ERI).
Bit 6
RIE
Description
0
Receive-end (RXI) and receive-error (ERI) interrupt requests are disabled (Initial value)
1
Receive-end (RXI) and receive-error (ERI) interrupt requests are enabled
Note: * RXI and ERI interrupt requests can be cleared by reading the value 1 from the RDRF, FER,
PER, or ORER flag, then clearing it to 0; or by clearing the RIE bit to 0.
Bit 5—Transmit Enable (TE): Enables or disables the start of SCI serial transmitting operations.
Bit 5
TE
Description
0
Transmitting disabled*1
1
Transmitting enabled*2
(Initial value)
Notes: 1. The TDRE bit is locked at 1 in SSR.
2. In the enabled state, serial transmitting starts when the TDRE bit in SSR is cleared to 0
after writing of transmit data into TDR. Select the transmit format in SMR before setting
the TE bit to 1.
272
Bit 4—Receive Enable (RE): Enables or disables the start of SCI serial receiving operations.
Bit 4
RE
Description
0
Receiving disabled*1
1
enabled*2
Receiving
(Initial value)
Notes: 1. Clearing the RE bit to 0 does not affect the RDRF, FER, PER, and ORER flags. These
flags retain their previous values.
2. In the enabled state, serial receiving starts when a start bit is detected in asynchronous
mode, or serial clock input is detected in synchronous mode. Select the receive format
in SMR before setting the RE bit to 1.
Bit 3—Multiprocessor Interrupt Enable (MPIE): Enables or disables multiprocessor interrupts.
The MPIE setting is valid only in asynchronous mode, and only if the MP bit is set to 1 in SMR.
The MPIE setting is ignored in synchronous mode or when the MP bit is cleared to 0.
Bit 3
MPIE
Description
0
Multiprocessor interrupts are disabled (normal receive operation)
[Clearing conditions]
The MPIE bit is cleared to 0.
MPB = 1 in received data.
(Initial value)
1
Multiprocessor interrupts are enabled*
Receive-data-full interrupts (RXI), receive-error interrupts (ERI), and setting of the RDRF,
FER, and ORER status flags in SSR are disabled until data with the multiprocessor bit
set to 1 is received.
Note: * The SCI does not transfer receive data from RSR to RDR, does not detect receive errors,
and does not set the RDRF, FER, and ORER flags in SSR. When it receives data in which
MPB = 1, the SCI sets the MPB bit to 1 in SSR, automatically clears the MPIE bit to 0,
enables RXI and ERI interrupts (if the RIE bit is set to 1 in SCR), and allows the FER and
ORER flags to be set.
273
Bit 2—Transmit-End Interrupt Enable (TEIE): Enables or disables the transmit-end interrupt
(TEI) requested if TDR does not contain new transmit data when the MSB is transmitted.
Bit 2
TEIE
Description
0
Transmit-end interrupt requests (TEI) are disabled*
1
Transmit-end interrupt requests (TEI) are enabled*
(Initial value)
Note: * TEI interrupt requests can be cleared by reading the value 1 from the TDRE flag in SSR,
then clearing the TDRE flag to 0, thereby also clearing the TEND flag to 0; or by clearing
the TEIE bit to 0.
Bits 1 and 0—Clock Enable 1 and 0 (CKE1/0): These bits select the SCI clock source and
enable or disable clock output from the SCK pin. Depending on the settings of CKE1 and CKE0,
the SCK pin can be used for generic input/output, serial clock output, or serial clock input.
The CKE0 setting is valid only in asynchronous mode, and only when the SCI is internally
clocked (CKE1 = 0). The CKE0 setting is ignored in synchronous mode, or when an external
clock source is selected (CKE1 = 1). Be sure to set the CKE1 and CKE0 bits before selecting the
SCI operating mode in SMR. For further details on selection of the SCI clock source, see table
10-9 in section 10.3, Operation.
Bit 1
CKE1
Bit 0
CKE0
Description
0
0
Asynchronous mode
Internal clock, SCK pin available for generic
input/output *1
Synchronous mode
Internal clock, SCK pin used for serial clock output *1
Asynchronous mode
Internal clock, SCK pin used for clock output *2
Synchronous mode
Internal clock, SCK pin used for serial clock output
Asynchronous mode
External clock, SCK pin used for clock input *3
Synchronous mode
External clock, SCK pin used for serial clock input
Asynchronous mode
External clock, SCK pin used for clock input *3
Synchronous mode
External clock, SCK pin used for serial clock input
1
1
0
1
Notes: 1. Initial value
2. The output clock frequency is the same as the bit rate.
3. The input clock frequency is 16 times the bit rate.
274
10.2.7 Serial Status Register (SSR)
SSR is an 8-bit register containing multiprocessor bit values, and status flags that indicate SCI
operating status.
Bit
7
6
5
4
3
2
1
0
TDRE
RDRF
ORER
FER
PER
TEND
MPB
MPBT
Initial value
1
0
0
0
0
1
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R
R
R/W
Multiprocessor
bit transfer
Value of multiprocessor bit to
be transmitted
Multiprocessor bit
Stores the received
multiprocessor bit value
Transmit end
Status flag indicating end of
transmission
Parity error
Status flag indicating detection of
a receive parity error
Framing error
Status flag indicating detection of a receive
framing error
Overrun error
Status flag indicating detection of a receive overrun error
Receive data register full
Status flag indicating that data has been received and stored in RDR
Transmit data register empty
Status flag indicating that transmit data has been transferred from TDR into
TSR and new data can be written in TDR
Note: * Only 0 can be written, to clear the flag.
275
The CPU can always read and write SSR, but cannot write 1 in the TDRE, RDRF, ORER, PER,
and FER flags. These flags can be cleared to 0 only if they have first been read while set to 1. The
TEND and MPB flags are read-only bits that cannot be written.
SSR is initialized to H'84 by a reset and in standby mode.
Bit 7—Transmit Data Register Empty (TDRE): Indicates that the SCI has loaded transmit data
from TDR into TSR and the next serial transmit data can be written in TDR.
Bit 7
TDRE
Description
0
TDR contains valid transmit data
[Clearing conditions]
Software reads TDRE while it is set to 1, then writes 0.
1
TDR does not contain valid transmit data
[Setting conditions]
The chip is reset or enters standby mode.
The TE bit in SCR is cleared to 0.
TDR contents are loaded into TSR, so new data can be written in TDR.
(Initial value)
Bit 6—Receive Data Register Full (RDRF): Indicates that RDR contains new receive data.
Bit 6
RDRF
Description
0
RDR does not contain new receive data
[Clearing conditions]
The chip is reset or enters standby mode.
Software reads RDRF while it is set to 1, then writes 0.
The DMAC reads data from RDR.
1
RDR contains new receive data
[Setting condition]
When serial data is received normally and transferred from RSR to RDR.
(Initial value)
Note: The RDR contents and RDRF flag are not affected by detection of receive errors or by
clearing of the RE bit to 0 in SCR. They retain their previous values. If the RDRF flag is still
set to 1 when reception of the next data ends, an overrun error occurs and receive data is
lost.
276
Bit 5—Overrun Error (ORER): Indicates that data reception ended abnormally due to an
overrun error.
Bit 5
ORER
Description
0
Receiving is in progress or has ended normally
[Clearing conditions]
The chip is reset or enters standby mode.
Software reads ORER while it is set to 1, then writes 0.
1
A receive overrun error occurred*2
[Setting condition]
Reception of the next serial data ends when RDRF = 1.
(Initial value)*1
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the ORER flag, which retains its
previous value.
2. RDR continues to hold the receive data before the overrun error, so subsequent receive
data is lost. Serial receiving cannot continue while the ORER flag is set to 1. In
synchronous mode, serial transmitting is also disabled.
Bit 4—Framing Error (FER): Indicates that data reception ended abnormally due to a framing
error in asynchronous mode.
Bit 4
FER
Description
0
Receiving is in progress or has ended normally
[Clearing conditions]
The chip is reset or enters standby mode.
Software reads FER while it is set to 1, then writes 0.
1
A receive framing error occurred*2
[Setting condition]
The stop bit at the end of receive data is checked and found to be 0.
(Initial value)*1
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the FER flag, which retains its previous
value.
2. When the stop bit length is 2 bits, only the first bit is checked. The second stop bit is not
checked. When a framing error occurs the SCI transfers the receive data into RDR but
does not set the RDRF flag. Serial receiving cannot continue while the FER flag is set
to 1. In synchronous mode, serial transmitting is also disabled.
277
Bit 3—Parity Error (PER): Indicates that data reception ended abnormally due to a parity error
in asynchronous mode.
Bit 3
PER
Description
0
Receiving is in progress or has ended normally*1
[Clearing conditions]
The chip is reset or enters standby mode.
Software reads PER while it is set to 1, then writes 0.
1
A receive parity error occurred*2
[Setting condition]
The number of 1s in receive data, including the parity bit, does not match the even or odd
parity setting of O/E in SMR.
(Initial value)
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the PER flag, which retains its previous
value.
2. When a parity error occurs the SCI transfers the receive data into RDR but does not set
the RDRF flag. Serial receiving cannot continue while the PER flag is set to 1. In
synchronous mode, serial transmitting is also disabled.
Bit 2—Transmit End (TEND): Indicates that when the last bit of a serial character was
transmitted TDR did not contain new transmit data, so transmission has ended. The TEND flag is
a read-only bit and cannot be written.
Bit 2
TEND
Description
0
Transmission is in progress
[Clearing conditions]
Software reads TDRE while it is set to 1, then writes 0 in the TDRE flag.
1
End of transmission
[Setting conditions]
The chip is reset or enters standby mode.
The TE bit is cleared to 0 in SCR.
TDRE is 1 when the last bit of a serial character is transmitted.
278
(Initial value)
Bit 1—Multiprocessor Bit (MPB): Stores the value of the multiprocessor bit in receive data
when a multiprocessor format is used in asynchronous mode. MPB is a read-only bit and cannot
be written.
Bit 1
MPB
Description
0
Multiprocessor bit value in receive data is 0*
1
Multiprocessor bit value in receive data is 1
(Initial value)
Note: * If the RE bit is cleared to 0 when a multiprocessor format is selected, MPB retains its
previous value.
Bit 0—Multiprocessor Bit Transfer (MPBT): Stores the value of the multiprocessor bit added to
transmit data when a multiprocessor format is selected for transmitting in asynchronous mode.
The MPBT setting is ignored in synchronous mode, when a multiprocessor format is not selected,
or when the SCI is not transmitting.
Bit 0
MPBT
Description
0
Multiprocessor bit value in transmit data is 0
1
Multiprocessor bit value in transmit data is 1
(Initial value)
10.2.8 Bit Rate Register (BRR)
BRR is an 8-bit register that, together with the CKS1 and CKS0 bits in SMR that select the baud
rate generator clock source, determines the serial communication bit rate.
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The CPU can always read and write BRR. BRR is initialized to H'FF by a reset and in standby
mode. The two SCI channels have independent baud rate generator control, so different values can
be set in the two channels.
Table 10-3 shows examples of BRR settings in asynchronous mode. Table 10-4 shows examples
of BRR settings in synchronous mode.
279
Table 10-3 Examples of Bit Rates and BRR Settings in Asynchronous Mode
ø (MHz)
2
2.097152
2.4576
3
Bit Rate
(bits/s)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
110
1
141
0.03
1
148
–0.04
1
174
–0.26
1
212
0.03
150
1
103
0.16
1
108
0.21
1
127
0
1
155
0.16
300
0
207
0.16
0
217
0.21
0
255
0
1
77
0.16
600
0
103
0.16
0
108
0.21
0
127
0
0
155
0.16
1200
0
51
0.16
0
54
–0.70
0
63
0
0
77
0.16
2400
0
25
0.16
0
26
1.14
0
31
0
0
38
0.16
4800
0
12
0.16
0
13
–2.48
0
15
0
0
19
–2.34
9600
0
6
–6.99
0
6
–2.48
0
7
0
0
9
–2.34
19200
0
2
8.51
0
2
13.78
0
3
0
0
4
–2.34
31250
0
1
0
0
1
4.86
0
1
22.88
0
2
0
38400
0
1
–18.62
0
1
–14.67
0
1
0
—
—
—
ø (MHz)
3.6864
4
4.9152
5
Bit Rate
(bits/s)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
110
2
64
0.70
2
70
0.03
2
86
0.31
2
88
–0.25
150
1
191
0
1
207
0.16
1
255
0
2
64
0.16
300
1
95
0
1
103
0.16
1
127
0
1
129
0.16
600
0
191
0
0
207
0.16
0
255
0
1
64
0.16
1200
0
95
0
0
103
0.16
0
127
0
0
129
0.16
2400
0
47
0
0
51
0.16
0
63
0
0
64
0.16
4800
0
23
0
0
25
0.16
0
31
0
0
32
–1.36
9600
0
11
0
0
12
0.16
0
15
0
0
15
1.73
19200
0
5
0
0
6
–6.99
0
7
0
0
7
1.73
31250
—
—
—
0
3
0
0
4
–1.70
0
4
0
38400
0
2
0
0
2
8.51
0
3
0
0
3
1.73
280
Table 10-3 Examples of Bit Rates and BRR Settings in Asynchronous Mode (cont)
ø (MHz)
6
6.144
7.3728
8
Bit Rate
(bits/s)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
110
2
106
–0.44
2
108
0.08
2
130
–0.07
2
141
0.03
150
2
77
0.16
2
79
0
2
95
0
2
103
0.16
300
1
155
0.16
1
159
0
1
191
0
1
207
0.16
600
1
77
0.16
1
79
0
1
95
0
1
103
0.16
1200
0
155
0.16
0
159
0
0
191
0
0
207
0.16
2400
0
77
0.16
0
79
0
0
95
0
0
103
0.16
4800
0
38
0.16
0
39
0
0
47
0
0
51
0.16
9600
0
19
–2.34
0
19
0
0
23
0
0
25
0.16
19200
0
9
–2.34
0
9
0
0
11
0
0
12
0.16
31250
0
5
0
0
5
2.40
0
6
5.33
0
7
0
38400
0
4
–2.34
0
4
0
0
5
0
0
6
–6.99
ø (MHz)
9.8304
10
12
12.288
Bit Rate
(bits/s)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
110
2
174
–0.26
2
177
–0.25
2
212
0.03
2
217
0.08
150
2
127
0
2
129
0.16
2
155
0.16
2
159
0
300
1
255
0
2
64
0.16
2
77
0.16
2
79
0
600
1
127
0
1
129
0.16
1
155
0.16
1
159
0
1200
0
255
0
1
64
0.16
1
77
0.16
1
79
0
2400
0
127
0
0
129
0.16
0
155
0.16
0
159
0
4800
0
63
0
0
64
0.16
0
77
0.16
0
79
0
9600
0
31
0
0
32
–1.36
0
38
0.16
0
39
0
19200
0
15
0
0
15
1.73
0
19
–2.34
0
19
0
31250
0
9
–1.70
0
9
0
0
11
0
0
11
2.40
38400
0
7
0
0
7
1.73
0
9
–2.34
0
9
0
281
Table 10-3 Examples of Bit Rates and BRR Settings in Asynchronous Mode (cont)
ø (MHz)
14
14.7456
16
Bit Rate
(bits/s)
n
N
Error
(%)
n
N
Error
(%)
n
N
Error
(%)
110
2
248
–0.17
3
64
0.70
3
70
0.03
150
2
181
0.16
2
191
0
2
207
0.16
300
2
90
0.16
2
95
0
2
103
0.16
600
1
181
0.16
1
191
0
1
207
0.16
1200
1
90
0.16
1
95
0
1
103
0.16
2400
0
181
0.16
0
191
0
0
207
0.16
4800
0
90
0.16
0
95
0
0
103
0.16
9600
0
45
–0.93
0
47
0
0
51
0.16
19200
0
22
–0.93
0
23
0
0
25
0.16
31250
0
13
0
0
14
–1.70
0
15
0
38400
0
10
3.57
0
11
0
0
12
0.16
282
Table 10-4 Examples of Bit Rates and BRR Settings in Synchronous Mode
ø (MHz)
2
4
8
10
16
Bit Rate
(bits/s)
n
N
n
N
n
N
n
N
n
N
110
3
70
—
—
—
—
—
—
—
—
250
2
124
2
249
3
124
—
—
3
249
500
1
249
2
124
2
249
—
—
3
124
1k
1
124
1
249
2
124
—
—
2
249
2.5 k
0
199
1
99
1
199
1
249
2
99
5k
0
99
0
199
1
99
1
124
1
199
10 k
0
49
0
99
0
199
0
249
1
99
25 k
0
19
0
39
0
79
0
99
0
159
50 k
0
9
0
19
0
39
0
49
0
79
100 k
0
4
0
9
0
19
0
24
0
39
250 k
0
1
0
3
0
7
0
9
0
15
500 k
0
0*
0
1
0
3
0
4
0
7
0
0*
0
1
—
—
0
3
2M
0
0*
—
—
0
1
2.5 M
—
—
0
0*
—
—
0
0*
1M
5M
Note: Settings with an error of 1% or less are recommended.
Legend
Blank: No setting available
—:
Setting possible, but error occurs
*:
Continuous transmit/receive not possible
The BRR setting is calculated as follows:
Asynchronous mode:
ø
N=
64
×22n–1
×B
×106 – 1
Synchronous mode:
N=
B:
N:
ø:
n:
ø
8 ×22n–1 ×B
×106 – 1
Bit rate (bits/s)
BRR setting for baud rate generator (0 ≤ N ≤ 255)
System clock frequency (MHz)
Baud rate generator clock source (n = 0, 1, 2, 3)
(For the clock sources and values of n, see the table below.)
283
SMR Settings
n
Clock Source
CKS1
CKS0
0
ø
0
0
1
ø/4
0
1
2
ø/16
1
0
3
ø/64
1
1
The bit rate error in asynchronous mode is calculated as follows.
ø ×106
Error (%) =
(N + 1) ×B ×64 ×22n–1
–1 ×100
284
Table 10-5 indicates the maximum bit rates in asynchronous mode for various system clock
frequencies. Tables 10-6 and 10-7 indicate the maximum bit rates with external clock input.
Table 10-5 Maximum Bit Rates for Various Frequencies (Asynchronous Mode)
Settings
ø (MHz)
Maximum Bit Rate (bits/s)
n
N
2
62500
0
0
2.097152
65536
0
0
2.4576
76800
0
0
3
93750
0
0
3.6864
115200
0
0
4
125000
0
0
4.9152
153600
0
0
5
156250
0
0
6
187500
0
0
6.144
192000
0
0
7.3728
230400
0
0
8
250000
0
0
9.8304
307200
0
0
10
312500
0
0
12
375000
0
0
12.288
384000
0
0
14
437500
0
0
14.7456
460800
0
0
16
500000
0
0
285
Table 10-6 Maximum Bit Rates with External Clock Input (Asynchronous Mode)
ø (MHz)
External Input Clock (MHz)
Maximum Bit Rate (bits/s)
2
0.5000
31250
2.097152
0.5243
32768
2.4576
0.6144
38400
3
0.7500
46875
3.6864
0.9216
57600
4
1.0000
62500
4.9152
1.2288
76800
5
1.2500
78125
6
1.5000
93750
6.144
1.5360
96000
7.3728
1.8432
115200
8
2.0000
125000
9.8304
2.4576
153600
10
2.5000
156250
12
3.0000
187500
12.288
3.0720
192000
14
3.5000
218750
14.7456
3.6864
230400
16
4.0000
250000
286
Table 10-7 Maximum Bit Rates with External Clock Input (Synchronous Mode)
ø (MHz)
External Input Clock (MHz)
Maximum Bit Rate (bits/s)
2
0.3333
333333.3
4
0.6667
666666.7
6
1.0000
1000000.0
8
1.3333
1333333.3
10
1.6667
1666666.7
12
2.0000
2000000.0
14
2.3333
2333333.3
16
2.6667
2666666.7
287
10.3 Operation
10.3.1 Overview
The SCI has an asynchronous mode in which characters are synchronized individually, and a
synchronous mode in which communication is synchronized with clock pulses. Serial
communication is possible in either mode. Asynchronous or synchronous mode and the
communication format are selected in SMR, as shown in table 10-8. The SCI clock source is
selected by the C/A bit in SMR and the CKE1 and CKE0 bits in SCR, as shown in table 10-9.
Asynchronous Mode
•
Data length is selectable: 7 or 8 bits.
•
Parity and multiprocessor bits are selectable. So is the stop bit length (1 or 2 bits). These
selections determine the communication format and character length.
•
In receiving, it is possible to detect framing errors, parity errors, overrun errors, and the break
state.
•
An internal or external clock can be selected as the SCI clock source.
— When an internal clock is selected, the SCI operates using the on-chip baud rate generator,
and can output a serial clock signal with a frequency matching the bit rate.
— When an external clock is selected, the external clock input must have a frequency
16 times the bit rate. (The on-chip baud rate generator is not used.)
Synchronous Mode
•
The communication format has a fixed 8-bit data length.
•
In receiving, it is possible to detect overrun errors.
•
An internal or external clock can be selected as the SCI clock source.
— When an internal clock is selected, the SCI operates using the on-chip baud rate generator,
and outputs a serial clock signal to external devices.
— When an external clock is selected, the SCI operates on the input serial clock. The on-chip
baud rate generator is not used.
288
Table 10-8 SMR Settings and Serial Communication Formats
SCI Communication Format
SMR Settings
Bit 7 Bit 6 Bit 2 Bit 5 Bit 3
C/A CHR MP
PE
STOP Mode
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
1
1
0
1
0
0
0
0
1
0
0
1
0
1
0
1
0
0
1
0
1
1
0
0
1
—
0
0
0
1
—
1
0
1
1
—
0
0
1
1
—
1
1
—
—
—
—
Asynchronous
mode
Data
Length
Multiprocessor
Bit
Parity
Bit
Stop
Bit
Length
8-bit data
Absent
Absent
1 bit
2 bits
Present
1 bit
2 bits
7-bit data
Absent
1 bit
2 bits
Present
1 bit
2 bits
Asynchronous
mode (multiprocessor
format)
8-bit data
Present
Absent
1 bit
2 bits
7-bit data
1 bit
2 bits
Synchronous
mode
8-bit data
Absent
None
Table 10-9 SMR and SCR Settings and SCI Clock Source Selection
SMR
SCR Settings
SCI Transmit/Receive Clock
Bit 7 Bit 1 Bit 0
C/A CKE1 CKE0
Mode
Clock Source
SCK Pin Function
0
0
0
Asynchronous mode
Internal
SCI does not use the SCK pin
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Outputs a clock with frequency
matching the bit rate
Synchronous mode
External
Inputs a clock with frequency
16 times the bit rate
Internal
Outputs the serial clock
External
Inputs the serial clock
289
10.3.2 Operation in Asynchronous Mode
In asynchronous mode each transmitted or received character begins with a start bit and ends with
a stop bit. Serial communication is synchronized one character at a time.
The transmitting and receiving sections of the SCI are independent, so full duplex communication
is possible. The transmitter and receiver are both double buffered, so data can be written and read
while transmitting and receiving are in progress, enabling continuous transmitting and receiving.
Figure 10-2 shows the general format of asynchronous serial communication. In asynchronous
serial communication the communication line is normally held in the mark (high) state. The SCI
monitors the line and starts serial communication when the line goes to the space (low) state,
indicating a start bit. One serial character consists of a start bit (low), data (LSB first), parity bit
(high or low), and stop bit (high), in that order.
When receiving in asynchronous mode, the SCI synchronizes at the falling edge of the start bit.
The SCI samples each data bit on the eighth pulse of a clock with a frequency 16 times the bit
rate. Receive data is latched at the center of each bit.
1
Serial data
(LSB)
0
D0
Idle (mark) state
1
(MSB)
D1
D2
D3
D4
D5
Start
bit
Transmit or receive data
1 bit
7 bits or 8 bits
D6
D7
0/1
Parity
bit
1
1
Stop
bit
1 bit or 1 bit or
no bit 2 bits
One unit of data (character or frame)
Figure 10-2 Data Format in Asynchronous Communication (Example: 8-Bit Data with
Parity and 2 Stop Bits)
290
Communication Formats: Table 10-10 shows the 12 communication formats that can be selected
in asynchronous mode. The format is selected by settings in SMR.
Table 10-10 Serial Communication Formats (Asynchronous Mode)
SMR Settings
Serial Communication Format and Frame Length
CHR
PE
MP
STOP
1
2
3
0
0
0
0
S
8-bit data
STOP
0
0
0
1
S
8-bit data
STOP STOP
0
1
0
0
S
8-bit data
P
STOP
0
1
0
1
S
8-bit data
P
STOP STOP
1
0
0
0
S
7-bit data
STOP
1
0
0
1
S
7-bit data
STOP STOP
1
1
0
0
S
7-bit data
P
STOP
1
1
0
1
S
7-bit data
P
STOP STOP
0
—
1
0
S
8 bit data
MPB STOP
0
—
1
1
S
8 bit data
MPB STOP STOP
1
—
1
0
S
7-bit data
MPB STOP
1
—
1
1
S
7-bit data
MPB STOP STOP
Legend
S:
Start bit
STOP: Stop bit
P:
Parity bit
MPB: Multiprocessor bit
291
4
5
6
7
8
9
10
11
12
Clock: An internal clock generated by the on-chip baud rate generator or an external clock input
from the SCK pin can be selected as the SCI transmit/receive clock. The clock source is selected
by the C/A bit in SMR and bits CKE1 and CKE0 in SCR. See table 10-9.
When an external clock is input at the SCK pin, it must have a frequency equal to 16 times the
desired bit rate.
When the SCI operates on an internal clock, it can output a clock signal at the SCK pin. The
frequency of this output clock is equal to the bit rate. The phase is aligned as in figure 10-3 so that
the rising edge of the clock occurs at the center of each transmit data bit.
0
D0
D1
D2
D3
D4
D5
D6
D7
0/1
1
1
1 frame
Figure 10-3 Phase Relationship between Output Clock and Serial Data
(Asynchronous Mode)
Transmitting and Receiving Data
SCI Initialization (Asynchronous Mode): Before transmitting or receiving, clear the TE and RE
bits to 0 in SCR, then initialize the SCI as follows.
When changing the communication mode or format, always clear the TE and RE bits to 0 before
following the procedure given below. Clearing TE to 0 sets the TDRE flag to 1 and initializes
TSR. Clearing RE to 0, however, does not initialize the RDRF, PER, FER, and ORER flags and
RDR, which retain their previous contents.
When an external clock is used, the clock should not be stopped during initialization or
subsequent operation. SCI operation becomes unreliable if the clock is stopped.
Figure 10-4 is a sample flowchart for initializing the SCI.
292
Start of initialization
Clear TE and RE bits
to 0 in SCR
Set CKE1 and CKE0 bits
in SCR (leaving TE and
RE bits cleared to 0)
1
Select communication
format in SMR
2
Set value in BRR
3
1. Select the clock source in SCR. Clear the RIE, TIE, TEIE,
MPIE, TE, and RE bits to 0. If clock output is selected in
asynchronous mode, clock output starts immediately after
the setting is made in SCR.
2. Select the communication format in SMR.
3. Write the value corresponding to the bit rate in BRR.
This step is not necessary when an external clock is used.
4. Wait for at least the interval required to transmit or receive
1 bit, then set the TE or RE bit to 1 in SCR. Set the RIE,
TIE, TEIE, and MPIE bits as necessary. Setting the TE
or RE bit enables the SCI to use the TxD or RxD pin.
Wait
1 bit interval
elapsed?
No
Yes
Set TE or RE bit to 1 in SCR
Set RIE, TIE, TEIE, and
MPIE bits as necessary
4
Transmitting or receiving
Figure 10-4 Sample Flowchart for SCI Initialization
293
Transmitting Serial Data (Asynchronous Mode): Figure 10-5 shows a sample flowchart for
transmitting serial data and indicates the procedure to follow.
1
Initialize
Start transmitting
2
Read TDRE flag in SSR
No
TDRE = 1?
Yes
1. SCI initialization: the transmit data output function
of the TxD pin is selected automatically.
2. SCI status check and transmit data write: read SSR,
check that the TDRE flag is 1, then write transmit data
in TDR and clear the TDRE flag to 0.
3. To continue transmitting serial data: after checking
that the TDRE flag is 1, indicating that data can be
written, write data in TDR, then clear the TDRE
flag to 0.
4. To output a break signal at the end of serial transmission:
set the DDR bit to 1 and clear the DR bit to 0
(DDR and DR are I/O port registers), then clear the
TE bit to 0 in SCR.
Write transmit data
in TDR and clear TDRE
flag to 0 in SSR
All data
transmitted?
No
3
Yes
Read TEND flag in SSR
TEND = 1?
No
Yes
Output break
signal?
No
4
Yes
Clear DR bit to 0,
set DDR bit to 1
Clear TE bit to 0 in SCR
End
Figure 10-5 Sample Flowchart for Transmitting Serial Data
294
In transmitting serial data, the SCI operates as follows.
•
The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0 the SCI
recognizes that TDR contains new data, and loads this data from TDR into TSR.
•
After loading the data from TDR into TSR, the SCI sets the TDRE flag to 1 and starts
transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty interrupt
(TXI) at this time.
Serial transmit data is transmitted in the following order from the TxD pin:
— Start bit:
One 0 bit is output.
— Transmit data:
7 or 8 bits are output, LSB first.
— Parity bit or multiprocessor bit: One parity bit (even or odd parity) or one multiprocessor
bit is output. Formats in which neither a parity bit nor a
multiprocessor bit is output can also be selected.
— Stop bit:
One or two 1 bits (stop bits) are output.
— Mark state:
Output of 1 bits continues until the start bit of the next
transmit data.
•
The SCI checks the TDRE flag when it outputs the stop bit. If the TDRE flag is 0, the SCI
loads new data from TDR into TSR, outputs the stop bit, then begins serial transmission of
the next frame. If the TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, outputs the
stop bit, then continues output of 1 bits in the mark state. If the TEIE bit is set to 1 in SCR, a
transmit-end interrupt (TEI) is requested at this time.
Figure 10-6 shows an example of SCI transmit operation in asynchronous mode.
1
Start
bit
0
Parity Stop Start
bit
bit
bit
Data
D0
D1
D7
0/1
1
0
Parity Stop
bit
bit
Data
D0
D1
D7
0/1
1
1
Idle (mark)
state
TDRE
TEND
TXI
interrupt
request
TXI interrupt handler
writes data in TDR and
clears TDRE flag to 0
TXI
interrupt
request
TEI interrupt request
1 frame
Figure 10-6 Example of SCI Transmit Operation in Asynchronous Mode
(8-Bit Data with Parity and 1 Stop Bit)
295
Receiving Serial Data (Asynchronous Mode): Figure 10-7 shows a sample flowchart for
receiving serial data and indicates the procedure to follow.
Initialize
1
Start receiving
Read ORER, PER,
and FER flags in SSR
PER ∨ FER ∨
ORER = 1?
2
Yes
3
No
Error handling
(continued on next page)
Read RDRF flag in SSR
4
No
RDRF = 1?
1. SCI initialization: the receive data function of
the RxD pin is selected automatically.
2., 3. Receive error handling and break
detection: if a receive error occurs, read the
ORER, PER, and FER flags in SSR to identify
the error. After executing the necessary error
handling, clear the ORER, PER, and FER
flags all to 0. Receiving cannot resume if any
of the ORER, PER, and FER flags remains
set to 1. When a framing error occurs, the
RxD pin can be read to detect the break state.
4. SCI status check and receive data read: read
SSR, check that RDRF is set to 1, then read
receive data from RDR and clear the RDRF
flag to 0. Notification that the RDRF flag has
changed from 0 to 1 can also be given by the
RXI interrupt.
5. To continue receiving serial data: check the
RDRF flag, read RDR, and clear the RDRF
flag to 0 before the stop bit of the current
frame is received.
Yes
Read receive data
from RDR, and clear
RDRF flag to 0 in SSR
No
Finished
receiving?
5
Yes
Clear RE bit to 0 in SCR
End
Figure 10-7 Sample Flowchart for Receiving Serial Data (1)
296
3
Error handling
No
ORER = 1?
Yes
Overrun error handling
No
FER = 1?
Yes
Yes
Break?
No
Framing error handling
Clear RE bit to 0 in SCR
No
PER = 1?
Yes
Parity error handling
Clear ORER, PER, and
FER flags to 0 in SSR
End
Figure 10-7 Sample Flowchart for Receiving Serial Data (2)
297
In receiving, the SCI operates as follows.
•
The SCI monitors the receive data line. When it detects a start bit, the SCI synchronizes
internally and starts receiving.
•
Receive data is stored in RSR in order from LSB to MSB.
•
The parity bit and stop bit are received.
After receiving, the SCI makes the following checks:
— Parity check:
The number of 1s in the receive data must match the even or odd parity
setting of the O/E bit in SMR.
— Stop bit check: The stop bit value must be 1. If there are two stop bits, only the first stop
bit is checked.
— Status check: The RDRF flag must be 0 so that receive data can be transferred from
RSR into RDR.
If these checks all pass, the RDRF flag is set to 1 and the received data is stored in RDR. If one of
the checks fails (receive error), the SCI operates as indicated in table 10-11.
Note: When a receive error occurs, further receiving is disabled. In receiving, the RDRF flag is
not set to 1. Be sure to clear the error flags.
•
When the RDRF flag is set to 1, if the RIE bit is set to 1 in SCR, a receive-data-full interrupt
(RXI) is requested. If the ORER, PER, or FER flag is set to 1 and the RIE bit in SCR is also
set to 1, a receive-error interrupt (ERI) is requested.
Table 10-11 Receive Error Conditions
Receive Error
Abbreviation
Condition
Data Transfer
Overrun error
ORER
Receiving of next data ends
while RDRF flag is still set to
1 in SSR
Receive data not transferred
from RSR to RDR
Framing error
FER
Stop bit is 0
Receive data transferred
from RSR to RDR
Parity error
PER
Parity of receive data differs
from even/odd parity setting
in SMR
Receive data transferred
from RSR to RDR
298
Figure 10-8 shows an example of SCI receive operation in asynchronous mode.
1
Start
bit
0
Parity Stop Start
bit
bit
bit
Data
D0
D1
D7
0/1
1
0
Parity Stop
bit
bit
Data
D0
D1
D7
0/1
1
1
Idle (mark)
state
RDRF
FER
RXI
request
1 frame
RXI interrupt handler
reads data in RDR and
clears RDRF flag to 0
Framing error,
ERI request
Figure 10-8 Example of SCI Receive Operation (8-Bit Data with Parity and One Stop Bit)
10.3.3 Multiprocessor Communication
The multiprocessor communication function enables several processors to share a single serial
communication line. The processors communicate in asynchronous mode using a format with an
additional multiprocessor bit (multiprocessor format).
In multiprocessor communication, each receiving processor is addressed by an ID. A serial
communication cycle consists of an ID-sending cycle that identifies the receiving processor, and a
data-sending cycle. The multiprocessor bit distinguishes ID-sending cycles from data-sending
cycles.
The transmitting processor starts by sending the ID of the receiving processor with which it wants
to communicate as data with the multiprocessor bit set to 1. Next the transmitting processor sends
transmit data with the multiprocessor bit cleared to 0.
Receiving processors skip incoming data until they receive data with the multiprocessor bit set
to 1. When they receive data with the multiprocessor bit set to 1, receiving processors compare the
data with their IDs. The receiving processor with a matching ID continues to receive further
incoming data. Processors with IDs not matching the received data skip further incoming data
until they again receive data with the multiprocessor bit set to 1. Multiple processors can send and
receive data in this way.
Figure 10-9 shows an example of communication among different processors using a
multiprocessor format.
299
Communication Formats: Four formats are available. Parity-bit settings are ignored when a
multiprocessor format is selected. For details see table 10-8.
Clock: See the description of asynchronous mode.
Transmitting
processor
Serial communication line
Receiving
processor A
Receiving
processor B
Receiving
processor C
Receiving
processor D
(ID = 01)
(ID = 02)
(ID = 03)
(ID = 04)
Serial data
H'01
H'AA
(MPB = 1)
(MPB = 0)
ID-sending cycle: receiving
processor address
Data-sending cycle:
data sent to receiving
processor specified by ID
Legend
MPB: Multiprocessor bit
Figure 10-9 Example of Communication among Processors using Multiprocessor Format
(Sending Data H'AA to Receiving Processor A)
300
Transmitting and Receiving Data
Transmitting Multiprocessor Serial Data: Figure 10-10 shows a sample flowchart for
transmitting multiprocessor serial data and indicates the procedure to follow.
1
Initialize
Start transmitting
2
Read TDRE flag in SSR
TDRE = 1?
No
Yes
Write transmit data in
TDR and set MPBT bit in SSR
Clear TDRE flag to 0
All data transmitted?
No
1. SCI initialization: the transmit data
output function of the TxD pin is
selected automatically.
2. SCI status check and transmit data
write: read SSR, check that the TDRE
flag is 1, then write transmit
data in TDR. Also set the MPBT flag to
0 or 1 in SSR. Finally, clear the TDRE
flag to 0.
3. To continue transmitting serial data:
after checking that the TDRE flag is 1,
indicating that data can be written,
write data in TDR, then clear the TDRE
flag to 0.
4. To output a break signal at the end of
serial transmission: set the DDR bit to
1 and clear the DR bit to 0 (DDR and
DR are I/O port registers), then clear
the TE bit to 0 in SCR.
3
Yes
Read TEND flag in SSR
TEND = 1?
No
Yes
Output break signal?
No
4
Yes
Clear DR bit to 0, set DDR bit to 1
Clear TE bit to 0 in SCR
End
Figure 10-10 Sample Flowchart for Transmitting Multiprocessor Serial Data
301
In transmitting serial data, the SCI operates as follows.
•
The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0 the SCI
recognizes that TDR contains new data, and loads this data from TDR into TSR.
•
After loading the data from TDR into TSR, the SCI sets the TDRE flag to 1 and starts
transmitting. If the TIE bit in SCR is set to 1, the SCI requests a transmit-data-empty interrupt
(TXI) at this time.
Serial transmit data is transmitted in the following order from the TxD pin:
—
—
—
—
—
•
Start bit:
Transmit data:
Multiprocessor bit:
Stop bit:
Mark state:
One 0 bit is output.
7 or 8 bits are output, LSB first.
One multiprocessor bit (MPBT value) is output.
One or two 1 bits (stop bits) are output.
Output of 1 bits continues until the start bit of the next transmit data.
The SCI checks the TDRE flag when it outputs the stop bit. If the TDRE flag is 0, the SCI
loads data from TDR into TSR, outputs the stop bit, then begins serial transmission of the
next frame. If the TDRE flag is 1, the SCI sets the TEND flag in SSR to 1, outputs the stop
bit, then continues output of 1 bits in the mark state. If the TEIE bit is set to 1 in SCR, a
transmit-end interrupt (TEI) is requested at this time.
Figure 10-11 shows an example of SCI transmit operation using a multiprocessor format.
Multiprocessor
bit
1
Serial
data
Start
bit
0
Stop Start
bit
bit
Data
D0
D1
Multiprocessor
bit
D7
0/1
1
0
Stop
bit
Data
D0
D1
D7
0/1
1
1
Idle (mark)
state
TDRE
TEND
TXI
request
TXI interrupt handler
writes data in TDR and
clears TDRE flag to 0
TXI
request
TEI request
1 frame
Figure 10-11 Example of SCI Transmit Operation (8-Bit Data with Multiprocessor Bit and
One Stop Bit)
302
Receiving Multiprocessor Serial Data: Figure 10-12 shows a sample flowchart for receiving
multiprocessor serial data and indicates the procedure to follow.
Initialize
1
1. SCI initialization: the receive data function
of the RxD pin is selected automatically.
2. ID receive cycle: set the MPIE bit to 1 in SCR.
3. SCI status check and ID check: read SSR,
check that the RDRF flag is set to 1, then read
data from RDR and compare with the
processor’s own ID. If the ID does not match,
set the MPIE bit to 1 again and clear the
RDRF flag to 0. If the ID matches, clear the
RDRF flag to 0.
4. SCI status check and data receiving: read
SSR, check that the RDRF flag is set to 1,
then read data from RDR.
5. Receive error handling and break detection:
if a receive error occurs, read the
ORER and FER flags in SSR to identify the error.
After executing the necessary error handling,
clear the ORER and FER flags both to 0.
Receiving cannot resume while either the ORER
or FER flag remains set to 1. When a framing
error occurs, the RxD pin can be read to detect
the break state.
Start receiving
Set MPIE bit to 1 in SCR
2
Read ORER and FER flags in SSR
FER ∨ ORER = 1
Yes
No
Read RDRF flag in SSR
3
No
RDRF = 1?
Yes
Read receive data from RDR
No
Own ID?
Yes
Read ORER and FER flags in SSR
FER ∨ ORER = 1
Yes
No
Read RDRF flag in SSR
4
No
RDRF = 1?
Yes
Read receive data from RDR
No
No
5
Finished receiving?
Yes
Error handling
(continued on next page)
Clear RE bit to 0 in SCR
End
Figure 10-12 Sample Flowchart for Receiving Multiprocessor Serial Data (1)
303
5
Error handling
No
ORER = 1?
Yes
Overrun error handling
No
FER = 1?
Yes
Yes
Break?
No
Framing error handling
Clear RE bit to 0 in SCR
Clear ORER, PER, and FER
flags to 0 in SSR
End
Figure 10-12 Sample Flowchart for Receiving Multiprocessor Serial Data (2)
304
Figure 10-13 shows an example of SCI receive operation using a multiprocessor format.
1
Start
bit
0
MPB
Data (ID1)
D0
D1
D7
1
Stop Start
Data (data1)
bit
bit
1
0
D0
D1
MPB
D7
0
Stop
bit
1
1
Idle (mark)
state
MPIE
RDRF
RDR value
ID1
RXI request
RXI handler reads
(multiprocessor
RDR data and clears
interrupt), MPIE = 0 RDRF flag to 0
Not own ID, so
MPIE bit is set
to 1 again
No RXI request,
RDR not updated
a. Own ID does not match data
1
Start
bit
0
MPB
Data (ID2)
D0
D1
D7
1
Stop Start
Data (data2)
bit
bit
1
0
D0
D1
MPB
D7
0
Stop
bit
1
1
Idle (mark)
state
MPIE
RDRF
RDR value
ID1
ID2
Data 2
RXI request
RXI interrupt handler Own ID, so receiving MPIE bit is set
(multiprocessor
reads RDR data and continues, with data to 1 again
interrupt), MPIE = 0 clears RDRF flag to 0 received by RXI
interrupt handler
b. Own ID matches data
Figure 10-13 Example of SCI Receive Operation (8-Bit Data with Multiprocessor Bit and
One Stop Bit)
305
10.3.4 Synchronous Operation
In synchronous mode, the SCI transmits and receives data in synchronization with clock pulses.
This mode is suitable for high-speed serial communication.
The SCI transmitter and receiver share the same clock but are otherwise independent, so full
duplex communication is possible. The transmitter and receiver are also double buffered, so
continuous transmitting or receiving is possible by reading or writing data while transmitting or
receiving is in progress.
Figure 10-14 shows the general format in synchronous serial communication.
Transfer direction
One unit (character or frame) of serial data
*
*
Serial clock
LSB
Serial data
Bit 0
MSB
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Don’t care
Don’t care
Note: * High except in continuous transmitting or receiving
Figure 10-14 Data Format in Synchronous Communication
In synchronous serial communication, each data bit is placed on the communication line from one
falling edge of the serial clock to the next. Data is guaranteed valid at the rise of the serial clock.
In each character, the serial data bits are transmitted in order from LSB (first) to MSB (last). After
output of the MSB, the communication line remains in the state of the MSB. In synchronous mode
the SCI receives data by synchronizing with the rise of the serial clock.
Communication Format: The data length is fixed at 8 bits. No parity bit or multiprocessor bit
can be added.
Clock: An internal clock generated by the on-chip baud rate generator or an external clock input
from the SCK pin can be selected by clearing or setting the CKE1 bit in SCR. See table 10-9.
When the SCI operates on an internal clock, it outputs the clock signal at the SCK pin. Eight clock
pulses are output per transmitted or received character. When the SCI is not transmitting or
receiving, the clock signal remains in the high state. When the SCI is only receiving, it receives in
units of two characters, so it outputs 16 clock pulses. To receive in units of one character, an
external clock source must be selected.
306
Transmitting and Receiving Data
SCI Initialization (Synchronous Mode): Before transmitting or receiving, clear the TE and RE
bits to 0 in SCR, then initialize the SCI as follows.
When changing the communication mode or format, always clear the TE and RE bits to 0 before
following the procedure given below. Clearing the TE bit to 0 sets the TDRE flag to 1 and
initializes TSR. Clearing the RE bit to 0, however, does not initialize the RDRF, PER, FER, and
ORE flags and RDR, which retain their previous contents.
Figure 10-15 is a sample flowchart for initializing the SCI.
Start of initialization
Clear TE and RE
bits to 0 in SCR
Set RIE, TIE, TEIE, MPIE,
CKE1, and CKE0 bits in SCR
(leaving TE and RE bits
cleared to 0)
1
1. Select the clock source in SCR. Clear the RIE, TIE, TEIE,
MPIE, TE, and RE bits to 0.
2. Select the communication format in SMR.
3. Write the value corresponding to the bit rate in BRR.
This step is not necessary when an external clock is used.
4. Wait for at least the interval required to transmit or receive
one bit, then set the TE or RE bit to 1 in SCR. Also set
the RIE, TIE, TEIE, and MPIE bits as necessary.
Setting the TE or RE bit enables the SCI to use the
TxD or RxD pin.
2
Select communication
format in SMR
3
Set value in BRR
Wait
1 bit interval
elapsed?
No
Yes
Set TE or RE to 1 in SCR
Set RIE, TIE, TEIE, and
MPIE bits as necessary
4
Start transmitting or receiving
Figure 10-15 Sample Flowchart for SCI Initialization
307
Transmitting Serial Data (Synchronous Mode): Figure 10-16 shows a sample flowchart for
transmitting serial data and indicates the procedure to follow.
Initialize
1
Start transmitting
Read TDRE flag in SSR
2
1. SCI initialization: the transmit data output function
of the TxD pin is selected automatically.
2. SCI status check and transmit data write: read SSR,
check that the TDRE flag is 1, then write transmit
data in TDR and clear the TDRE flag to 0.
3. To continue transmitting serial data: after checking
that the TDRE flag is 1, indicating that data can be
written, write data in TDR, then clear the TDRE flag
to 0.
No
TDRE = 1?
Yes
Write transmit data in
TDR and clear TDRE flag
to 0 in SSR
All data
transmitted?
No
3
Yes
Read TEND flag in SSR
TEND = 1?
No
Yes
Clear TE bit to 0 in SCR
End
Figure 10-16 Sample Flowchart for Serial Transmitting
308
In transmitting serial data, the SCI operates as follows.
•
The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0 the SCI
recognizes that TDR contains new data, and loads this data from TDR into TSR.
•
After loading the data from TDR into TSR, the SCI sets the TDRE flag to 1 and starts
transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty interrupt
(TXI) at this time.
If clock output is selected, the SCI outputs eight serial clock pulses. If an external clock
source is selected, the SCI outputs data in synchronization with the input clock. Data is output
from the TxD pin in order from LSB (bit 0) to MSB (bit 7).
•
The SCI checks the TDRE flag when it outputs the MSB (bit 7). If the TDRE flag is 0, the
SCI loads data from TDR into TSR and begins serial transmission of the next frame. If the
TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, and after transmitting the MSB,
holds the TxD pin in the MSB state. If the TEIE bit in SCR is set to 1, a transmit-end
interrupt (TEI) is requested at this time.
•
After the end of serial transmission, the SCK pin is held in a constant state.
309
Figure 10-17 shows an example of SCI transmit operation.
Transmit
direction
Serial clock
Serial data
Bit 0
Bit 1
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
TDRE
TEND
TXI
request
TXI interrupt handler
writes data in TDR
and clears TDRE
flag to 0
TXI
request
1 frame
Figure 10-17 Example of SCI Transmit Operation
310
TEI
request
Receiving Serial Data: Figure 10-18 shows a sample flowchart for receiving serial data and
indicates the procedure to follow. When switching from asynchronous mode to synchronous
mode, make sure that the ORER, PER, and FER flags are cleared to 0. If the FER or PER flag is
set to 1 the RDRF flag will not be set and both transmitting and receiving will be disabled.
Initialize
1
1.
SCI initialization: the receive data function of
the RxD pin is selected automatically.
2., 3. Receive error handling: if a receive error
occurs, read the ORER flag in SSR, then after
executing the necessary error handling, clear
the ORER flag to 0. Neither transmitting nor
receiving can resume while the ORER flag
remains set to 1.
4. SCI status check and receive data read: read
SSR, check that the RDRF flag is set to 1,
then read receive data from RDR and clear
the RDRF flag to 0. Notification that the RDRF
flag has changed from 0 to 1 can also be
given by the RXI interrupt.
5. To continue receiving serial data: check the
RDRF flag, read RDR, and clear the RDRF
flag to 0 before the MSB (bit 7) of the current
frame is received.
Start receiving
Read ORER flag in SSR
ORER = 1?
2
Yes
3
No
Read RDRF flag in SSR
Error handling
4
No
RDRF = 1?
Yes
Read receive data
from RDR, and clear
RDRF flag to 0 in SSR
No
5
Finished
receiving?
Yes
Clear RE bit to 0 in SCR
End
Figure 10-18 Sample Flowchart for Serial Receiving (1)
311
3
Error handling
Overrun error handling
Clear ORER flag to 0 in SSR
End
Figure 10-18 Sample Flowchart for Serial Receiving (2)
In receiving, the SCI operates as follows.
•
The SCI synchronizes with serial clock input or output and initializes internally.
•
Receive data is stored in RSR in order from LSB to MSB.
After receiving the data, the SCI checks that the RDRF flag is 0 so that receive data can be
transferred from RSR to RDR. If this check passes, the RDRF flag is set to 1 and the received
data is stored in RDR. If the check does not pass (receive error), the SCI operates as indicated
in table 10-11.
•
After setting the RDRF flag to 1, if the RIE bit is set to 1 in SCR, the SCI requests a receivedata-full interrupt (RXI). If the ORER flag is set to 1 and the RIE bit in SCR is also set to 1,
the SCI requests a receive-error interrupt (ERI).
312
Figure 10-19 shows an example of SCI receive operation.
Receive direction
Serial clock
Serial data
Bit 7
Bit 0
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
RDRF
ORER
RXI
request
RXI interrupt handler
reads data in RDR and
clears RDRF flag to 0
RXI
request
Overrun error,
ERI request
1 frame
Figure 10-19 Example of SCI Receive Operation
Transmitting and Receiving Serial Data Simultaneously (Synchronous Mode): Figure 10-20
shows a sample flowchart for transmitting and receiving serial data simultaneously and indicates
the procedure to follow.
313
1
Initialize
Start transmitting and receiving
2
Read TDRE flag in SSR
No
TDRE = 1?
Yes
Write transmit data in TDR and
clear TDRE flag to 0 in SSR
Read ORER flag in SSR
Yes
ORER = 1?
3
No
Error handling
4
Read RDRF flag in SSR
No
RDRF = 1?
Yes
Read receive data from RDR
and clear RDRF flag to 0 in SSR
No
End of transmitting and
receiving?
5
1. SCI initialization: the transmit data
output function of the TxD pin and
receive data input function of the
RxD pin are selected, enabling
simultaneous transmitting and
receiving.
2. SCI status check and transmit
data write: read SSR, check that
the TDRE flag is 1, then write
transmit data in TDR and clear
the TDRE flag to 0.
Notification that the TDRE flag has
changed from 0 to 1 can also be
given by the TXI interrupt.
3. Receive error handling: if a receive
error occurs, read the ORER flag in
SSR, then after executing the necessary error handling, clear the ORER
flag to 0.
Neither transmitting nor receiving
can resume while the ORER flag
remains set to 1.
4. SCI status check and receive
data read: read SSR, check that
the RDRF flag is 1, then read
receive data from RDR and clear
the RDRF flag to 0. Notification
that the RDRF flag has changed
from 0 to 1 can also be given
by the RXI interrupt.
5. To continue transmitting and
receiving serial data: check the
RDRF flag, read RDR, and clear
the RDRF flag to 0 before the
MSB (bit 7) of the current frame
is received. Also check that the
TDRE flag is (bit 7) of the current
frame is received. Also check that
the TDRE flag is set to 1, indicating that data can be written, write
data in TDR, then clear the TDRE
flag to 0 before the MSB (bit 7) of
the current frame is transmitted.
When the DMAC is activated by
a transmit-data-empty interrupt
request (TXI) to write data in TDR,
the TDRE flag is checked and
cleared automatically.
Yes
Clear TE and RE bits to 0 in SCR
End
Note: * When switching from transmitting or receiving to simultaneous
transmitting and receiving, clear the TE and RE bits both to 0,
then set the TE and RE bits both to 1.
Figure 10-20 Sample Flowchart for Serial Transmitting
314
10.4 SCI Interrupts
The SCI has four interrupt request sources: TEI (transmit-end interrupt), ERI (receive-error
interrupt), RXI (receive-data-full interrupt), and TXI (transmit-data-empty interrupt). Table 10-12
lists the interrupt sources and indicates their priority. These interrupts can be enabled and disabled
by the TIE, TEIE, and RIE bits in SCR. Each interrupt request is sent separately to the interrupt
controller.
The TXI interrupt is requested when the TDRE flag is set to 1 in SSR. The TEI interrupt is
requested when the TEND flag is set to 1 in SSR.
The RXI interrupt is requested when the RDRF flag is set to 1 in SSR. The ERI interrupt is
requested when the ORER, PER, or FER flag is set to 1 in SSR.
Table 10-12 SCI Interrupt Sources
Interrupt
Description
Priority
ERI
Receive error (ORER, FER, or PER)
High
RXI
Receive data register full (RDRF)
TXI
Transmit data register empty (TDRE)
TEI
Transmit end (TEND)
Low
315
10.5 Usage Notes
Note the following points when using the SCI.
TDR Write and TDRE Flag: The TDRE flag in SSR is a status flag indicating the loading of
transmit data from TDR into TSR. The SCI sets the TDRE flag to 1 when it transfers data from
TDR to TSR.
Data can be written into TDR regardless of the state of the TDRE flag. If new data is written in
TDR when the TDRE flag is 0, the old data stored in TDR will be lost because this data has not
yet been transferred to TSR. Before writing transmit data in TDR, be sure to check that the TDRE
flag is set to 1.
Simultaneous Multiple Receive Errors: Table 10-13 indicates the state of SSR status flags when
multiple receive errors occur simultaneously. When an overrun error occurs the RSR contents are
not transferred to RDR, so receive data is lost.
Table 10-13 SSR Status Flags and Transfer of Receive Data
RDRF
ORER
FER
PER
Receive Data
Transfer
RSR →RDR
1
1
0
0
×
Overrun error
0
0
1
0
o
Framing error
0
0
0
1
o
Parity error
1
1
1
0
×
Overrun error + framing error
1
1
0
1
×
Overrun error + parity error
0
0
1
1
o
Framing error + parity error
1
1
1
1
×
Overrun error + framing error + parity error
SSR Status Flags
Notes:
o:
Receive Errors
Receive data is transferred from RSR to RDR.
× Receive data is not transferred from RSR to RDR.
316
Break Detection and Processing: Break signals can be detected by reading the RxD pin directly
when a framing error (FER) is detected. In the break state the input from the RxD pin consists of
all 0s, so the FER flag is set and the parity error flag (PER) may also be set. In the break state the
SCI receiver continues to operate, so if the FER flag is cleared to 0 it will be set to 1 again.
Sending a Break Signal: When the TE bit is cleared to 0 the TxD pin becomes an I/O port, the
level and direction (input or output) of which are determined by DR and DDR bits. This feature
can be used to send a break signal.
After the serial transmitter is initialized, the DR value substitutes for the mark state until the TE
bit is set to 1 (the TxD pin function is not selected until the TE bit is set to 1). The DDR and DR
bits should therefore both be set to 1 beforehand.
To send a break signal during serial transmission, clear the DR bit to 0, then clear the TE bit to 0.
When the TE bit is cleared to 0 the transmitter is initialized, regardless of its current state, so the
TxD pin becomes an output port outputting the value 0.
Receive Error Flags and Transmitter Operation (Synchronous Mode Only): When a receive
error flag (ORER, PER, or FER) is set to 1 the SCI will not start transmitting, even if the TDRE
flag is cleared to 0. Be sure to clear the receive error flags to 0 when starting to transmit. Note that
clearing the RE bit to 0 does not clear the receive error flags to 0.
Receive Data Sampling Timing in Asynchronous Mode and Receive Margin: In asynchronous
mode the SCI operates on a base clock with 16 times the bit rate frequency. In receiving, the SCI
synchronizes internally with the fall of the start bit, which it samples on the base clock. Receive
data is latched at the rising edge of the eighth base clock pulse. See figure 10-21.
317
16 clocks
8 clocks
0
15 0
7
7
15 0
Internal
base clock
Receive data
(RxD)
Start bit
D0
D1
Synchronization
sampling timing
Data sampling
timing
Figure 10-21 Receive Data Sampling Timing in Asynchronous Mode
The receive margin in asynchronous mode can therefore be expressed as in equation (1).
1
| D – 0.5 |
) – (L – 0.5) F –
(1 + F) | × 100%...................(1)
2N
N
Receive margin (%)
Ratio of clock frequency to bit rate (N = 16)
Clock duty cycle (D = 0 to 1.0)
Frame length (L = 9 to 12)
Absolute deviation of clock frequency
M = | (0.5 –
M:
N:
D:
L:
F:
From equation (1), if F = 0 and D = 0.5 the receive margin is 46.875%, as given by equation (2).
D = 0.5, F = 0
M = [0.5 – 1/(2 ×16)] ×100%
= 46.875%.................................................................................................(2)
This is a theoretical value. A reasonable margin to allow in system designs is 20% to 30%.
318
Restrictions in Synchronous Mode: When an external clock source is used in synchronous
mode, after TDR is reset, wait at least 5 clock counts (5ø) before inputting the transmit clock. If
the clock is input four states after the reset of TDR or earlier, an operation error may occur (figure
10-22).
SCK
t
TDRE
D0
D1
D2
D3
D4
D5
D6
Note: When using an external clock, make sure t is 5 clock cycles or greater.
Figure 10-22 Transmission in Synchronous Mode (Example)
319
D7
320
Section 11 A/D Converter
11.1 Overview
The H8/3004 and H8/3005 include a 10-bit successive-approximations A/D converter with a
selection of up to eight analog input channels.
11.1.1 Features
A/D converter features are listed below.
•
10-bit resolution
•
Eight input channels
•
Selectable analog conversion voltage range
The analog voltage conversion range can be programmed by input of an analog reference
voltage at the VREF pin.
•
High-speed conversion
Conversion time: maximum 8.4 µs per channel (with 16 MHz system clock)
•
Two conversion modes
Single mode: A/D conversion of one channel
Scan mode: continuous conversion on one to four channels
•
Four 16-bit data registers
A/D conversion results are transferred for storage into data registers corresponding to the
channels.
•
Sample-and-hold function
•
A/D conversion can be externally triggered
•
A/D interrupt requested at end of conversion
At the end of A/D conversion, an A/D end interrupt (ADI) can be requested.
321
11.1.2 Block Diagram
Figure 11-1 shows a block diagram of the A/D converter.
On-chip
data bus
AV SS
AN 0
AN 5
ADCR
ADCSR
ADDRD
–
AN 2
AN 4
ADDRC
+
AN 1
AN 3
ADDRB
10-bit D/A
ADDRA
V REF
Successiveapproximations register
AVCC
Bus interface
Module data bus
Analog
multiplexer
ø/8
Comparator
Control circuit
Sample-andhold circuit
ø/16
AN 6
AN 7
ADI
ADTRG
Legend
ADCR:
ADCSR:
ADDRA:
ADDRB:
ADDRC:
ADDRD:
A/D control register
A/D control/status register
A/D data register A
A/D data register B
A/D data register C
A/D data register D
Figure 11-1 A/D Converter Block Diagram
322
11.1.3 Input Pins
Table 11-1 summarizes the A/D converter’s input pins. The eight analog input pins are divided
into two groups: group 0 (AN0 to AN3), and group 1 (AN4 to AN7). AVCC and AVSS are the
power supply for the analog circuits in the A/D converter. VREF is the A/D conversion reference
voltage.
Table 11-1 A/D Converter Pins
Pin Name
Abbreviation
I/O
Function
Analog power supply pin
AVCC
Input
Analog power supply
Analog ground pin
AVSS
Input
Analog ground and reference voltage
Reference voltage pin
VREF
Input
Analog reference voltage
Analog input pin 0
AN0
Input
Group 0 analog inputs
Analog input pin 1
AN1
Input
Analog input pin 2
AN2
Input
Analog input pin 3
AN3
Input
Analog input pin 4
AN4
Input
Analog input pin 5
AN5
Input
Analog input pin 6
AN6
Input
Analog input pin 7
AN7
Input
A/D external trigger input pin
ADTRG
Input
Group 1 analog inputs
External trigger input for starting A/D conversion
323
11.1.4 Register Configuration
Table 11-2 summarizes the A/D converter’s registers.
Table 11-2 A/D Converter Registers
Address*1
Name
Abbreviation
R/W
Initial Value
H'FFE0
A/D data register A (high)
ADDRAH
R
H'00
H'FFE1
A/D data register A (low)
ADDRAL
R
H'00
H'FFE2
A/D data register B (high)
ADDRBH
R
H'00
H'FFE3
A/D data register B (low)
ADDRBL
R
H'00
H'FFE4
A/D data register C (high)
ADDRCH
R
H'00
H'FFE5
A/D data register C (low)
ADDRCL
R
H'00
H'FFE6
A/D data register D (high)
ADDRDH
R
H'00
H'FFE7
A/D data register D (low)
ADDRDL
R
H'00
H'FFE8
A/D control/status register
ADCSR
R/(W)*2
H'00
H'FFE9
A/D control register
ADCR
R/W
H'7F
Notes: 1. Lower 16 bits of the address
2. Only 0 can be written in bit 7, to clear the flag.
324
11.2 Register Descriptions
11.2.1 A/D Data Registers A to D (ADDRA to ADDRD)
Bit
ADDRn
14
12
10
8
6
5
4
3
2
1
0
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 —
—
—
—
—
—
15
13
11
9
7
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
(n = A to D)
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A/D conversion data
10-bit data giving an
A/D conversion result
Reserved bits
The four A/D data registers (ADDRA to ADDRD) are 16-bit read-only registers that store the
results of A/D conversion.
An A/D conversion produces 10-bit data, which is transferred for storage into the A/D data
register corresponding to the selected channel. The upper 8 bits of the result are stored in the
upper byte of the A/D data register. The lower 2 bits are stored in the lower byte. Bits 5 to 0 of an
A/D data register are reserved bits that always read 0. Table 11-3 indicates the pairings of analog
input channels and A/D data registers.
The CPU can always read and write the A/D data registers. The upper byte can be read directly,
but the lower byte is read through a temporary register (TEMP). For details see section 11.3, CPU
Interface.
The A/D data registers are initialized to H'0000 by a reset and in standby mode.
Table 11-3 Analog Input Channels and A/D Data Registers
Analog Input Channel
Group 0
Group 1
A/D Data Register
AN0
AN4
ADDRA
AN1
AN5
ADDRB
AN2
AN6
ADDRC
AN3
AN7
ADDRD
325
11.2.2 A/D Control/Status Register (ADCSR)
Bit
7
6
5
4
3
2
1
0
ADF
ADIE
ADST
SCAN
CKS
CH2
CH1
CH0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Channel select 2 to 0
These bits select analog
input channels
Clock select
Selects the A/D conversion time
Scan mode
Selects single mode or scan mode
A/D start
Starts or stops A/D conversion
A/D interrupt enable
Enables and disables A/D end interrupts
A/D end flag
Indicates end of A/D conversion
Note: * Only 0 can be written, to clear the flag.
ADCSR is an 8-bit readable/writable register that selects the mode and controls the A/D converter.
ADCSR is initialized to H'00 by a reset and in standby mode.
326
Bit 7—A/D End Flag (ADF): Indicates the end of A/D conversion.
Bit 7
ADF
Description
0
[Clearing condition]
Cleared by reading ADF while ADF = 1, then writing 0 in ADF
1
[Setting conditions]
Single mode: A/D conversion ends
Scan mode: A/D conversion ends in all selected channels
(Initial value)
Bit 6—A/D Interrupt Enable (ADIE): Enables or disables the interrupt (ADI) requested at the
end of A/D conversion.
Bit 6
ADIE
Description
0
A/D end interrupt request (ADI) is disabled
1
A/D end interrupt request (ADI) is enabled
(Initial value)
Bit 5—A/D Start (ADST): Starts or stops A/D conversion. The ADST bit remains set to 1 during
A/D conversion. It can also be set to 1 by external trigger input at the ADTRG pin.
Bit 5
ADST
Description
0
A/D conversion is stopped
1
Single mode: A/D conversion starts; ADST is automatically cleared to 0 when conversion
ends.
Scan mode: A/D conversion starts and continues, cycling among the selected channels,
until ADST is cleared to 0 by software, by a reset, or by a transition to standby mode.
(Initial value)
327
Bit 4—Scan Mode (SCAN): Selects single mode or scan mode. For further information on
operation in these modes, see section 11.4, Operation. Clear the ADST bit to 0 before switching
the conversion mode.
Bit 4
SCAN
Description
0
Single mode
1
Scan mode
(Initial value)
Bit 3—Clock Select (CKS): Selects the A/D conversion time. Clear the ADST bit to 0 before
switching the conversion time.
Bit 3
CKS
Description
0
Conversion time = 266 states (maximum)
1
Conversion time = 134 states (maximum)
(Initial value)
Bits 2 to 0—Channel Select 2 to 0 (CH2 to CH0): These bits and the SCAN bit select the analog
input channels. Clear the ADST bit to 0 before changing the channel selection.
Group
Selection
Channel Selection
Description
CH2
CH1
CH0
Single Mode
Scan Mode
0
0
0
AN0 (Initial value)
AN0
1
AN1
AN0, AN1
0
AN2
AN0 to AN2
1
AN3
AN0 to AN3
0
AN4
AN4
1
AN5
AN4, AN5
0
AN6
AN4 to AN6
1
AN7
AN4 to AN7
1
1
0
1
328
11.2.3 A/D Control Register (ADCR)
Bit
7
6
5
4
3
2
1
0
TRGE
—
—
—
—
—
—
—
Initial value
0
1
1
1
1
1
1
1
Read/Write
R/W
—
—
—
—
—
—
—
Reserved bits
Trigger enable
Enables or disables external triggering of A/D conversion
ADCR is an 8-bit readable/writable register that enables or disables external triggering of A/D
conversion. ADCR is initialized to H'7F by a reset and in standby mode.
Bit 7—Trigger Enable (TRGE): Enables or disables external triggering of A/D conversion.
Bit 7
TRGE
Description
0
A/D conversion cannot be externally triggered
1
A/D conversion starts at the falling edge of the external trigger signal (ADTRG)
Bits 6 to 0—Reserved: Read-only bits, always read as 1.
329
(Initial value)
11.3 CPU Interface
ADDRA to ADDRD are 16-bit registers, but they are connected to the CPU by an 8-bit data bus.
Therefore, although the upper byte can be be accessed directly by the CPU, the lower byte is read
through an 8-bit temporary register (TEMP).
An A/D data register is read as follows. When the upper byte is read, the upper-byte value is
transferred directly to the CPU and the lower-byte value is transferred into TEMP. Next, when the
lower byte is read, the TEMP contents are transferred to the CPU.
When reading an A/D data register, always read the upper byte before the lower byte. It is possible
to read only the upper byte, but if only the lower byte is read, incorrect data may be obtained.
Figure 11-2 shows the data flow for access to an A/D data register.
Upper-byte read
CPU
(H'AA)
Module data bus
Bus interface
TEMP
(H'40)
ADDRnH
(H'AA)
ADDRnL
(H'40)
(n = A to D)
Lower-byte read
CPU
(H'40)
Module data bus
Bus interface
TEMP
(H'40)
ADDRnH
(H'AA)
ADDRnL
(H'40)
(n = A to D)
Figure 11-2 A/D Data Register Access Operation (Reading H'AA40)
330
11.4 Operation
The A/D converter operates by successive approximations with 10-bit resolution. It has two
operating modes: single mode and scan mode.
11.4.1 Single Mode (SCAN = 0)
Single mode should be selected when only one A/D conversion on one channel is required. A/D
conversion starts when the ADST bit is set to 1 by software, or by external trigger input. The
ADST bit remains set to 1 during A/D conversion and is automatically cleared to 0 when
conversion ends.
When conversion ends the ADF bit is set to 1. If the ADIE bit is also set to 1, an ADI interrupt is
requested at this time. To clear the ADF flag to 0, first read ADCSR, then write 0 in ADF.
When the mode or analog input channel must be switched during analog conversion, to prevent
incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making
the necessary changes, set the ADST bit to 1 to start A/D conversion again. The ADST bit can be
set at the same time as the mode or channel is changed.
Typical operations when channel 1 (AN1) is selected in single mode are described next.
Figure 11-3 shows a timing diagram for this example.
1.
Single mode is selected (SCAN = 0), input channel AN1 is selected (CH2 = CH1 = 0,
CH0 = 1), the A/D interrupt is enabled (ADIE = 1), and A/D conversion is started
(ADST = 1).
2.
When A/D conversion is completed, the result is transferred into ADDRB. At the same time
the ADF flag is set to 1, the ADST bit is cleared to 0, and the A/D converter becomes idle.
3.
Since ADF = 1 and ADIE = 1, an ADI interrupt is requested.
4.
The A/D interrupt handling routine starts.
5.
The routine reads ADCSR, then writes 0 in the ADF flag.
6.
The routine reads and processes the conversion result (ADDRB).
7.
Execution of the A/D interrupt handling routine ends. After that, if the ADST bit is set to 1,
A/D conversion starts again and steps 2 to 7 are repeated.
331
Figure 11-3 Example of A/D Converter Operation (Single Mode, Channel 1 Selected)
332
Note: * Vertical arrows ( ) indicate instructions executed by software.
ADDRD
ADDRC
ADDRB
ADDRA
State of channel 3
(AN 3)
State of channel 2
(AN 2)
Read conversion result
A/D conversion result (2)
Idle
Clear *
A/D conversion result (1)
A/D conversion (2)
Set *
Read conversion result
Idle
Idle
Idle
Clear *
State of channel 1
(AN 1)
A/D conversion (1)
Set *
Idle
Idle
A/D conversion
starts
State of channel 0
(AN 0)
ADF
ADST
ADIE
Set *
11.4.2 Scan Mode (SCAN = 1)
Scan mode is useful for monitoring analog inputs in a group of one or more channels. When the
ADST bit is set to 1 by software or external trigger input, A/D conversion starts on the first
channel in the group (AN0 when CH2 = 0, AN4 when CH2 = 1). When two or more channels are
selected, after conversion of the first channel ends, conversion of the second channel (AN1 or
AN5) starts immediately. A/D conversion continues cyclically on the selected channels until the
ADST bit is cleared to 0. The conversion results are transferred for storage into the A/D data
registers corresponding to the channels.
When the mode or analog input channel selection must be changed during analog conversion, to
prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After
making the necessary changes, set the ADST bit to 1. A/D conversion will start again from the
first channel in the group. The ADST bit can be set at the same time as the mode or channel
selection is changed.
Typical operations when three channels in group 0 (AN0 to AN2) are selected in scan mode are
described next. Figure 11-4 shows a timing diagram for this example.
1.
Scan mode is selected (SCAN = 1), scan group 0 is selected (CH2 = 0), analog input channels
AN0 to AN2 are selected (CH1 = 1, CH0 = 0), and A/D conversion is started (ADST = 1).
2.
When A/D conversion of the first channel (AN0) is completed, the result is transferred into
ADDRA. Next, conversion of the second channel (AN1) starts automatically.
3.
Conversion proceeds in the same way through the third channel (AN2).
4.
When conversion of all selected channels (AN0 to AN2) is completed, the ADF flag is set to 1
and conversion of the first channel (AN0) starts again. If the ADIE bit is set to 1, an ADI
interrupt is requested at this time.
5.
Steps 2 to 4 are repeated as long as the ADST bit remains set to 1. When the ADST bit is
cleared to 0, A/D conversion stops. After that, if the ADST bit is set to 1, A/D conversion
starts again from the first channel (AN0).
333
Figure 11-4 Example of A/D Converter Operation (Scan Mode,
Channels AN0 to AN2 Selected)
334
Idle
Idle
Idle
A/D conversion (1)
Transfer
A/D conversion result (1)
Idle
Idle
Clear*1
Idle
A/D conversion result (3)
A/D conversion result (2)
A/D conversion result (4)
Idle
A/D conversion (5)*2
A/D conversion time
A/D conversion (4)
Idle
A/D conversion (3)
Idle
A/D conversion (2)
Notes: 1. Vertical arrows ( ) indicate instructions executed by software.
2. Data currently being converted is ignored.
ADDRD
ADDRC
ADDRB
ADDRA
State of channel 3
(AN 3)
State of channel 2
(AN 2)
State of channel 1
(AN 1)
State of channel 0
(AN 0)
ADF
ADST
Set *1
Continuous A/D conversion
Clear* 1
11.4.3 Input Sampling and A/D Conversion Time
The A/D converter has a built-in sample-and-hold circuit. The A/D converter samples the analog
input at a time tD after the ADST bit is set to 1, then starts conversion. Figure 11-5 shows the A/D
conversion timing. Table 11-4 indicates the A/D conversion time.
As indicated in figure 11-5, the A/D conversion time includes tD and the input sampling time. The
length of tD varies depending on the timing of the write access to ADCSR. The total conversion
time therefore varies within the ranges indicated in table 11-4.
In scan mode, the values given in table 11-4 apply to the first conversion. In the second and
subsequent conversions the conversion time is fixed at 256 states when CKS = 0 or 118 states
when CKS = 1.
(1)
ø
Address bus
(2)
Write signal
Input sampling
timing
ADF
tD
t SPL
t CONV
Legend
(1):
ADCSR write cycle
(2):
ADCSR address
tD :
Synchronization delay
t SPL : Input sampling time
t CONV: A/D conversion time
Figure 11-5 A/D Conversion Timing
335
Table 11-4 A/D Conversion Time (Single Mode)
CKS = 0
CKS = 1
Symbol
Min
Typ
Max
Min
Typ
Max
Synchronization delay
tD
10
—
17
6
—
9
Input sampling time
tSPL
—
80
—
—
40
—
A/D conversion time
tCONV
259
—
266
131
—
134
Note: Values in the table are numbers of states.
11.4.4 External Trigger Input Timing
A/D conversion can be externally triggered. When the TRGE bit is set to 1 in ADCR, external
trigger input is enabled at the ADTRG pin. A high-to-low transition at the ADTRG pin sets the
ADST bit to 1 in ADCSR, starting A/D conversion. Other operations, in both single and scan
modes, are the same as if the ADST bit had been set to 1 by software. Figure 11-6 shows the
timing.
ø
ADTRG
Internal trigger
signal
ADST
A/D conversion
Figure 11-6 External Trigger Input Timing
336
11.5 Interrupts
The A/D converter generates an interrupt (ADI) at the end of A/D conversion. The ADI interrupt
request can be enabled or disabled by the ADIE bit in ADCSR.
11.6 Usage Notes
When using the A/D converter, note the following points:
Analog Input Voltage Range: During A/D conversion, the voltages input to the analog input pins
ANn should be in the range AVSS ≤ ANn ≤ VREF. (n = 0 to 7)
AVCC and AVSS Input Voltages: AVSS should have the following values: AVSS = VSS.
If the A/D converter is not used, the values should be AVCC = VCC and AVSS = VSS.
VREF Input Range: The analog reference voltage input at the VREF pin should be in the range
VREF ≤ AVCC. If the A/D converter is not used, the value should be VREF = VCC.
337
338
Section 12 RAM
12.1 Overview
The H8/3004 has 2 kbytes of on-chip static RAM, and the H8/3005 has 4 kbytes. The RAM is
connected to the CPU by a 16-bit data bus. The CPU accesses both byte data and word data in two
states, making the RAM suitable for rapid data transfer.
The H8/3004 on-chip RAM is assigned to addresses H'FF710 to H'FFF0F. The H8/3005 on-chip
RAM is assigned to addresses H'FEF10 to H'FFF0F. The RAM enable bit (RAME) in the system
control register (SYSCR) can enable or disable the on-chip RAM.
12.1.1 Block Diagram
Figures 12-1 and 12-2 show block diagrams of the H8/3004 and H8/3005 on-chip RAM.
On-chip data bus (upper 8 bits)
On-chip data bus (lower 8 bits)
Bus interface
H'F710 *
H'F711 *
H'F712
H'F713 *
On-chip RAM
H'FF0E*
H'FF0F*
Even addresses
Odd addresses
Note: * Lower 16 bits of the address
Figure 12-1 RAM Block Diagram (H8/3004)
339
On-chip data bus (upper 8 bits)
On-chip data bus (lower 8 bits)
Bus interface
H'EF10*
H'EF11*
H'EF12*
H'EF13*
On-chip RAM
H'FF0E*
H'FF0F*
Even addresses
Odd addresses
Note: * Lower 16 bits of the address
Figure 12-2 RAM Block Diagram (H8/3005)
12.1.2 Register Configuration
The on-chip RAM is controlled by the system control register (SYSCR). Table 12-1 gives the
address and initial value of SYSCR.
Table 12-1 RAM Control Register
Address*
Name
Abbreviation
R/W
Initial Value
H'FFF2
System control register
SYSCR
R/W
H'0B
Note: * Lower 16 bits of the address
340
12.2 System Control Register (SYSCR)
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
—
RAME
Initial value
0
0
0
0
1
0
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
—
R/W
RAM enable bit
Enables or
disables
on-chip RAM
Reserved bit
NMI edge select
User bit enable
Standby timer select 2 to 0
Software standby
One function of SYSCR is to enable or disable access to the on-chip RAM. The on-chip RAM is
enabled or disabled by the RAME bit in SYSCR. For details about the other bits, see section 3.3,
System Control Register.
Bit 0—RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is
initialized at the rising edge of the input at the RES pin. It is not initialized in software standby
mode.
Bit 0
RAME
Description
0
On-chip RAM is disabled
1
On-chip RAM is enabled
(Initial value)
341
12.3 Operation
When the RAME bit is set to 1, on-chip RAM is enabled. Accesses to addresses H'FF710 to
H'FFF0F in the H8/3004, and to addresses H'FEF10 to H'FFF0F in the H8/3005, are directed to
the on-chip RAM space. When the RAME bit is cleared to 0, accesses to such addresses are
directed to external address space.
342
Section 13 Clock Pulse Generator
13.1 Overview
The H8/3004 and H8/3005 have a built-in clock pulse generator (CPG) that generates the system
clock (ø) and other internal clock signals (ø/2 to ø/4096). The clock pulse generator consists of an
oscillator circuit, a duty adjustment circuit, and prescalers.
13.1.1 Block Diagram
Figure 13-1 shows a block diagram of the clock pulse generator.
CPG
XTAL
Oscillator
EXTAL
Duty
adjustment
circuit
Prescalers
ø
ø/2 to ø/4096
Figure 13-1 Block Diagram of Clock Pulse Generator
343
13.2 Oscillator Circuit
Clock pulses can be supplied by connecting a crystal resonator, or by input of an external clock
signal.
13.2.1 Connecting a Crystal Resonator
Circuit Configuration: A crystal resonator can be connected as in the example in figure 13-2.
The damping resistance Rd should be selected according to table 13-1. An AT-cut parallelresonance crystal should be used.
C L1
EXTAL
XTAL
Rd
C L1 = C L2 = 10 pF to 22 pF
C L2
Figure 13-2 Connection of Crystal Resonator (Example)
Table 13-1 Damping Resistance Value
Frequency (MHz)
2
4
8
10
12
16
Rd (Ω)
1k
500
200
0
0
0
Crystal Resonator: Figure 13-3 shows an equivalent circuit of the crystal resonator. The crystal
resonator should have the characteristics listed in table 13-2.
CL
L
Rs
XTAL
EXTAL
CO
AT-cut parallel-resonance type
Figure 13-3 Crystal Resonator Equivalent Circuit
344
Table 13-2 Crystal Resonator Parameters
Frequency (MHz)
2
4
8
10
12
16
Rs max (Ω)
500
120
80
70
60
50
Co max (pF)
7
Use a crystal resonator with a frequency equal to the system clock frequency (ø).
Notes on Board Design: When a crystal resonator is connected, the following points should be
noted:
Other signal lines should be routed away from the oscillator circuit to prevent induction from
interfering with correct oscillation. See figure 13-4.
When the board is designed, the crystal resonator and its load capacitors should be placed as close
as possible to the XTAL and EXTAL pins.
Avoid
Signal A
Signal B
H8/3004 and H8/3005
C L2
XTAL
EXTAL
C L1
Figure 13-4 Example of Incorrect Board Design
345
13.2.2 External Clock Input
Circuit Configuration: An external clock signal can be input as shown in the examples in
figure 13-5. In example b, the clock should be held high in standby mode.
If the XTAL pin is left open, the stray capacitance should not exceed 10 pF.
EXTAL
External clock input
XTAL
Open
a. XTAL pin left open
EXTAL
XTAL
External clock input
74HC04
b. Complementary clock input at XTAL pin
Figure 13-5 External Clock Input (Examples)
346
External Clock: The external clock frequency should be equal to the system clock frequency (ø).
Table 13-3 and figure 13-6 indicate the clock timing.
Table 13-3 Clock Timing
VCC = 2.7 V to 5.5 V
VCC = 5.0 V ± 10%
Item
Symbol
Min
Max
Min
Max
Unit
Test Conditions
External clock
rise time
tEXr
—
10
—
5
ns
Figure 13-6
External clock
fall time
tEXf
—
10
—
5
ns
External clock
input duty
(a/tcyc)
—
30
70
30
70
%
40
60
40
60
%
ø ≥ 5 MHz Figure
13-6
ø < 5 MHz
ø clock duty
(b/tcyc)
—
40
60
40
60
%
ø ≥ 5 MHz
tcyc
a
VCC × 0.5
EXTAL
tEXr
tEXf
tcyc
b
VCC × 0.5
ø
Figure 13-6 External Clock Input Timing
347
Figure 13-7 shows the timing for the external clock output stabilization delay time. The oscillator
and duty correction circuit have the function of regulating the waveform of the external clock
input to the EXTAL pin. When the specified clock signal is input to the EXTAL pin, internal clock
signal output is confirmed after the elapse of the external clock output stabilization delay time
(tDEXT). As clock signal output is not confirmed during the tDEXT period, the reset signal should
be driven low and the reset state maintained during this time.
Conditions: VCC = 2.7 to 5.5 V, AVCC = 2.7 to 5.5 V, VSS = AVSS = 0 V
Item
Symbol
Min
Max
Unit
Notes
External clock output stabilization
delay time
tDEXT*
500
—
µs
Figure 13-7
Note: * tDEXT includes a 10 tcyc RES pulse width (tRESW).
VCC
STBY
2.7 V
VIH
EXTAL
ø
RES
tDEXT*
Note: * tDEXT includes a 10 tcyc RES pulse width (tRESW).
Figure 13-7 External Clock Output Stabilization Delay Time
13.3 Duty Adjustment Circuit
When the oscillator frequency is 5 MHz or higher, the duty adjustment circuit adjusts the duty
cycle of the clock signal from the oscillator to generate the system clock (ø).
13.4 Prescalers
The prescalers divide the system clock (ø) to generate internal clocks (ø/2 to ø/4096).
348
Section 14 Power-Down State
14.1 Overview
The H8/3004 and H8/3005 have a power-down state that greatly reduces power consumption by
halting CPU functions. The power-down state includes the following three modes:
•
•
•
Sleep mode
Software standby mode
Hardware standby mode
Table 14-1 indicates the methods of entering and exiting these power-down modes and the status
of the CPU and on-chip supporting modules in each mode.
Table 14-1 Power-Down State
State
Mode
Entering
Conditions
Clock
CPU
CPU
Supporting
Registers Functions RAM
I/O
Ports
Exiting
Conditions
Sleep
mode
SLEEP instruc- Active
tion executed
while SSBY = 0
in SYSCR
Halted
Held
Active
Held
Held
• Interrupt
• RES
• STBY
Software
standby
mode
SLEEP instruc- Halted
tion executed
while SSBY = 1
in SYSCR
Halted
Held
Halted
and
reset
Held
Held
•
•
•
•
Halted
Undeter
mined
Halted
and
reset
Held*
High
• STBY
impedance • RES
Hardware Low input at
standby
STBY pin
mode
Halted
NMI
IRQ0 to IRQ2
RES
STBY
Note: * The RAME bit must be cleared to 0 in SYSCR before the transition from the program execution state
to hardware standby mode.
Legend
SYSCR: System control register
SSBY: Software standby bit
349
14.2 Register Configuration
The H8/3004 and H8/3005’s system control register (SYSCR) controls the power-down state.
Table 14-2 summarizes this register.
Table 14-2 Control Register
Address*
Name
Abbreviation
R/W
Initial Value
H'FFF2
System control register
SYSCR
R/W
H'0B
Note: * Lower 16 bits of the address.
14.2.1 System Control Register (SYSCR)
Bit
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
—
RAME
Initial value
0
0
0
0
1
0
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
—
R/W
RAM enable
Reserved bit
NMI edge select
User bit enable
Standby timer select 2 to 0
These bits select the
waiting time at exit from
software standby mode
Software standby
Enables transition to
software standby mode
SYSCR is an 8-bit readable/writable register. Bit 7 (SSBY) and bits 6 to 4 (STS2 to STS0) control
the power-down state. For information on the other SYSCR bits, see section 3.3, System Control
Register.
350
Bit 7—Software Standby (SSBY): Enables transition to software standby mode. When software
standby mode is exited by an external interrupt, this bit remains set to 1 after the return to normal
operation. To clear this bit, write 0.
Bit 7
SSBY
Description
0
SLEEP instruction causes transition to sleep mode
1
SLEEP instruction causes transition to software standby mode
(Initial value)
Bits 6 to 4—Standby Timer Select (STS2 to STS0): These bits select the length of time the CPU
and on-chip supporting modules wait for the clock to settle when software standby mode is exited
by an external interrupt. If the clock is generated by a crystal resonator, set these bits according to
the clock frequency so that the waiting time will be at least 8 ms. See table 14-3. If an external
clock is used, any setting is permitted.
Bit 6
STS2
Bit 5
STS1
Bit 4
STS0
Description
0
0
0
Waiting time = 8192 states
1
Waiting time = 16384 states
0
Waiting time = 32768 states
1
Waiting time = 65536 states
0
—
Waiting time = 131072 states
1
—
Illegal setting
1
1
351
(Initial value)
14.3 Sleep Mode
14.3.1 Transition to Sleep Mode
When the SSBY bit is cleared to 0 in the system control register (SYSCR), execution of the
SLEEP instruction causes a transition from the program execution state to sleep mode.
Immediately after executing the SLEEP instruction the CPU halts, but the contents of its internal
registers are retained. The on-chip supporting modules do not halt in sleep mode.
14.3.2 Exit from Sleep Mode
Sleep mode is exited by an interrupt, or by input at the RES or STBY pin.
Exit by Interrupt: An interrupt terminates sleep mode and causes a transition to the interrupt
exception handling state. Sleep mode is not exited by an interrupt source in an on-chip supporting
module if the interrupt is disabled in the on-chip supporting module. Sleep mode is not exited by
an NMI interrupt if masked in the CPU.
Exit by RES Input: Low input at the RES pin exits from sleep mode to the reset state.
Exit by STBY Input: Low input at the STBY pin exits from sleep mode to hardware standby
mode.
352
14.4 Software Standby Mode
14.4.1 Transition to Software Standby Mode
To enter software standby mode, execute the SLEEP instruction while the SSBY bit is set to 1 in
SYSCR.
In software standby mode, current dissipation is reduced to an extremely low level because the
CPU, clock, and on-chip supporting modules all halt. The on-chip supporting modules are reset.
As long as the specified voltage is supplied, however, CPU register contents and on-chip RAM
data are retained. The settings of the I/O ports are also held.
14.4.2 Exit from Software Standby Mode
Software standby mode can be exited by input of an external interrupt at the NMI, IRQ0, IRQ1, or
IRQ2 pin, or by input at the RES or STBY pin.
Exit by Interrupt: When an NMI, IRQ0, IRQ1, or IRQ2 interrupt request signal is received, the
clock oscillator begins operating. After the oscillator settling time selected by bits STS2 to STS0
in SYSCR, stable clock signals are supplied to the entire H8/3004 and H8/3005 chip, software
standby mode ends, and interrupt exception handling begins. Software standby mode is not exited
if the interrupt enable bits of interrupts IRQ0, IRQ1, and IRQ2 are cleared to 0, or if these
interrupts are masked in the CPU.
Exit by RES Input: When the RES input goes low, the clock oscillator starts and clock pulses are
supplied immediately to the entire H8/3004 and H8/3005 chip. The RES signal must be held low
long enough for the clock oscillator to stabilize. When RES goes high, the CPU starts reset
exception handling.
Exit by STBY Input: Low input at the STBY pin causes a transition to hardware standby mode.
353
14.4.3 Selection of Waiting Time for Exit from Software Standby Mode
Bits STS2 to STS0 in SYSCR should be set as follows.
Crystal Resonator: Set STS2 to STS0 so that the waiting time (for the clock to stabilize) is at
least 8 ms. Table 14-3 indicates the waiting times that are selected by STS2 to STS0 settings at
various system clock frequencies.
External Clock: Any value may be set in the clock-halving version. Normally the minimum value
(STS2 = STS1 = STS0 = 1) is recommended. In the 1:1 clock version, any value other than the
minimum value may be set.
Table 14-3 Clock Frequency and Waiting Time for Clock to Settle
Waiting
STS2 STS1 STS0 Time
16 MHZ 12 MHz 10 MHz 8 MHz
6 MHz
4 MHz
2 MHz
Unit
0
0
0
8192
states
0.51
0.65
0.8
1.0
1.3
2.0
4.1
ms
0
0
1
16384
states
1.0
1.3
1.6
2.0
2.7
4.1
8.2
0
1
0
32768
states
2.0
2.7
3.3
4.1
5.5
8.2
16.4
0
1
1
65536
states
4.1
5.5
6.6
8.2
10.9
16.4
32.8
1
0
—
131072
states
8.2
10.9
13.1
16.4
21.8
32.8
65.5
1
1
—
Illegal setting
: Recommended setting
Note: * This setting cannot be used in the 1:1 clock version.
354
14.4.4 Sample Application of Software Standby Mode
Figure 14-1 shows an example in which software standby mode is entered at the fall of NMI and
exited at the rise of NMI.
With the NMI edge select bit (NMIEG) cleared to 0 in SYSCR (selecting the falling edge), an
NMI interrupt occurs. Next the NMIEG bit is set to 1 (selecting the rising edge) and the SSBY bit
is set to 1; then the SLEEP instruction is executed to enter software standby mode.
Software standby mode is exited at the next rising edge of the NMI signal .
Clock
oscillator
ø
NMI
NMIEG
SSBY
NMI interrupt
handler
NMIEG = 1
SSBY = 1
Software standby
mode (powerdown state)
Oscillator
settling time
(tosc2)
NMI exception
handling
SLEEP
instruction
Figure 14-1 NMI Timing for Software Standby Mode (Example)
14.4.5 Note
The I/O ports retain their existing states in software standby mode. If a port is in the high output
state, its output current is not reduced.
355
14.5 Hardware Standby Mode
14.5.1 Transition to Hardware Standby Mode
Regardless of its current state, the chip enters hardware standby mode whenever the STBY pin
goes low. Hardware standby mode reduces power consumption drastically by halting all functions
of the CPU and on-chip supporting modules. All modules are reset except the on-chip RAM. As
long as the specified voltage is supplied, on-chip RAM data is retained. I/O ports are placed in the
high-impedance state.
Clear the RAME bit to 0 in SYSCR before STBY goes low to retain on-chip RAM data.
The inputs at the mode pins (MD1 to MD0) should not be changed during hardware standby mode.
14.5.2 Exit from Hardware Standby Mode
Hardware standby mode is exited by inputs at the STBY and RES pins. While RES is low, when
STBY goes high, the clock oscillator starts running. RES should be held low long enough for the
clock oscillator to settle. When RES goes high, reset exception handling begins, followed by a
transition to the program execution state.
14.5.3 Timing for Hardware Standby Mode
Figure 14-2 shows the timing relationships for hardware standby mode. To enter hardware standby
mode, first drive RES low, then drive STBY low. To exit hardware standby mode, first drive
STBY high, wait for the clock to settle, then bring RES from low to high.
Clock
oscillator
RES
STBY
Oscillator
settling time
Reset
exception
handling
Figure 14-2 Hardware Standby Mode Timing
356
Section 15 Electrical Characteristics
15.1 Absolute Maximum Ratings
Table 15-1 lists the absolute maximum ratings.
Table 15-1 Absolute Maximum Ratings
—Preliminary—
Item
Symbol
Value
Unit
Power supply voltage
VCC
–0.3 to +7.0
V
Input voltage (except port 7)
VIN
–0.3 to VCC +0.3
V
Input voltage (port 7)
VIN
–0.3 to AVCC +0.3
V
Reference voltage
VREF
–0.3 to AVCC +0.3
V
Analog power supply voltage
AVCC
–0.3 to +7.0
V
Analog input voltage
VAN
–0.3 to AVCC +0.3
V
Operating temperature
Topr
Regular specifications: –20 to +75
°C
Wide-range specifications: –40 to +85
°C
–55 to +125
°C
Storage temperature
Tstg
Caution: Permanent damage to the chip may result if absolute maximum ratings are exceeded.
357
15.2 Electrical Characteristics
15.2.1 DC Characteristics
Table 15-2 lists the DC characteristics. Table 15-3 lists the permissible output currents.
Table 15-2 DC Characteristics
Conditions: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V*, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Schmitt
trigger input
voltages
Input high
voltage
Input low
voltage
Output high
voltage
Symbol
Port A,
P80 to P82,
VT
–
VT
+
+
PB0 to PB3
VT – VT
RES, STBY,
NMI, MD1,
MD0
VIH
–
Min
Typ
Max
Unit Test Conditions
1.0
—
—
V
—
—
VCC ×0.7
V
0.4
—
—
V
VCC – 0.7 —
VCC + 0.3 V
EXTAL
VCC ×0.7
—
VCC + 0.3 V
Port 7
2.0
—
AVCC + 0.3 V
Ports 6, 9, P83,
PB4 to PB7,
D7 to D0
2.0
—
VCC + 0.3 V
–0.3
—
0.5
V
NMI, EXTAL,
ports 6, 7,
9, P83,
PB4 to PB7,
D7 to D0
–0.3
—
0.8
V
All output pins VOH
VCC – 0.5 —
—
V
IOH = –200 µA
3.5
—
V
IOH = –1 mA
RES, STBY,
MD1, MD0
VIL
—
Note: * If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
358
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC ,
VSS = AVSS = 0 V*1, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Output low
voltage
Symbol
Min
Typ
Max
Unit
Test Conditions
All output pins VOL
(except RESO)
—
—
0.4
V
IOL = 1.6 mA
Ports B,
A19 to A0
—
—
1.0
V
IOL = 10 mA
RESO
—
—
0.4
V
IOL = 2.6 mA
—
—
1.0
µA
VIN = 0.5 to
VCC – 0.5 V
—
—
1.0
µA
VIN = 0.5 to
AVCC – 0.5 V
—
—
1.0
µA
VIN = 0.5 to
VCC – 0.5 V
—
—
10.0
µA
—
—
50
pF
—
—
15
VIN = 0 V
f = 1 MHz
Ta = 25°C
—
45
60
mA
f = 16 MHz
Sleep mode
—
32
45
mA
f = 16 MHz
Standby
mode*3
—
0.01
5.0
µA
Ta ≤ 50°C
—
—
20.0
µA
50°C < Ta
Input leakage STBY, NMI,
current
RES,
MD1, MD0
|IIN|
Port 7
Three-state
leakage
current
(off state)
Ports 6,
8 to B,
A19 to A0,
D7 to D0
|ITS1|
RESO
Input
NMI
capacitance
All input pins
except NMI
CIN
Current
Normal
dissipation*2 operation
ICC
Notes: 1. If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
2. Current dissipation values are for VIHmin = VCC – 0.5 V and VILmax = 0.5 V with all output
pins unloaded and the on-chip pull-up transistors in the off state.
3. The values are for VRAM ≤ VCC < 4.5 V, VIHmin = VCC ×0.9, and VILmax = 0.3 V.
359
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V*1, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Symbol
Min
Typ
Max
Unit Test Conditions
Analog power During A/D
supply current conversion
AICC
—
1.2
2.0
mA
—
0.01
5.0
µA
—
0.3
0.6
mA
—
0.01
5.0
µA
2.0
—
—
V
Idle
Reference
current
During A/D
conversion
AICC
Idle
RAM standby voltage
VRAM
VREF = 5.0 V
Notes: 1. If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
2. Current dissipation values are for VIHmin = VCC – 0.5 V and VILmax = 0.5 V with all output
pins unloaded and the on-chip pull-up transistors in the off state.
3. The values are for VRAM < VCC < 4.5 V, VIHmin = VCC ×0.9, and VILmax = 0.3 V.
Conditions: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V*, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Schmitt
trigger input
voltages
Input high
voltage
Symbol
Min
Typ
Max
Unit Test Conditions
VT–
VCC ×0.2
—
—
V
VT+
—
—
VCC ×0.7
V
—
—
V
VCC ×0.9
—
VCC + 0.3
V
EXTAL
VCC ×0.7
—
VCC + 0.3
V
Port 7
VCC ×0.7
—
AVCC + 0.3 V
Ports 6, 9, P83,
PB4 to PB7,
D7 to D0
VCC ×0.7
—
VCC + 0.3
Port A,
P80 to P82,
PB0 to PB3
RES, STBY,
NMI, MD1,
MD0
VT+ – VT– VCC ×0.07
VIH
V
Note: * If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
360
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V*, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Symbol
Min
Typ
Max
Unit
VIL
–0.3
—
VCC ×0.1
V
NMI, EXTAL,
ports 6, 7,
9, P83,
PB4 to PB7,
D7 to D0
–0.3
—
VCC ×0.2
V
VCC < 4.0 V
0.8
V
VCC =
4.0 to 5.5 V
Output high
voltage
All output pins VOH
VCC – 0.5 —
—
V
IOH = –200 µA
VCC – 1.0 —
—
V
IOH = –1 mA
Output low
voltage
All output pins VOL
(except RESO)
—
—
0.4
V
IOL = 1.6 mA
Ports B,
A19 to A0
—
—
1.0
V
VCC ≤ 4 V,
IOL = 5 mA,
4 V ≤ VCC ≤ 5.5 V,
IOL = 10 mA
RESO
—
—
0.4
V
IOL = 1.6 mA
—
—
1.0
µA
VIN = 0.5 to
VCC – 0.5 V
—
—
1.0
µA
VIN = 0.5 to
AVCC – 0.5 V
—
—
1.0
µA
VIN = 0.5 to
VCC – 0.5 V
—
—
10.0
µA
Input low
voltage
RES, STBY,
MD1, MD0
Input leakage STBY, NMI,
current
RES,
MD1, MD0
|IIN|
Port 7
Three-state
leakage
current
(off state)
Ports 6,
8 to B,
A19 to A0,
D7 to D0
RESO
|ITS1|
Test Conditions
Note: * If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
361
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V*1, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Symbol
Min
Typ
Max
Unit Test Conditions
CIN
—
—
50
pF
—
—
15
VIN = 0 V
f = 1 MHz
Ta = 25°C
—
12
(3.0 V)
33.8
(5.5 V)
mA
f = 8 MHz
Sleep mode
—
8
(3.0 V)
25.0
(5.5 V)
mA
f = 8 MHz
Standby
mode*3
—
0.01
5.0
µA
Ta ≤ 50°C
—
—
20.0
µA
50°C < Ta
—
1.0
2.0
mA
AVCC = 3.0 V
—
1.2
—
mA
AVCC = 5.0 V
—
0.01
5.0
µA
—
0.2
0.4
mA
VREF = 3.0 V
—
0.3
—
mA
VREF = 5.0 V
—
0.01
5.0
µA
2.0
—
—
V
Input
capacitance
NMI
Current
dissipation*2
Normal
operation
All input pins
except NMI
Analog power During A/D
supply current conversion
ICC*4
AICC
Idle
Reference
current
During A/D
conversion
AICC
Idle
RAM standby voltage
VRAM
Notes: 1. If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
2. Current dissipation values are for VIHmin = VCC – 0.5 V and VILmax = 0.5 V with all output
pins unloaded.
3. The values are for VRAM ≤ VCC < 2.7 V, VIHmin = VCC ×0.9, and VILmax = 0.3 V.
4. ICC depends on VCC and f as follows:
ICCmax = 3.0 (mA) + 0.7 (mA/MHz · V) ×VCC ×f [normal mode]
ICCmax = 3.0 (mA) + 0.5 (mA/MHz · V) ×VCC ×f [sleep mode]
362
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V*, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Schmitt
trigger input
voltages
Input high
voltage
Input low
voltage
Output high
voltage
Symbol
Min
Typ
Max
Unit Test Conditions
VT–
VCC ×0.2
—
—
V
VT+
—
—
VCC ×0.7
V
—
—
V
VCC ×0.9
—
VCC + 0.3
V
EXTAL
VCC ×0.7
—
VCC + 0.3
V
Port 7
VCC ×0.7
—
AVCC + 0.3 V
Ports 6, 9, P83,
PB4 to PB7,
D7 to D0
VCC ×0.7
—
VCC + 0.3
Port A,
P80 to P82,
PB0 to PB3
RES, STBY,
NMI, MD1,
MD0
VT+ – VT– VCC ×0.07
VIH
V
–0.3
—
VCC ×0.1
V
NMI, EXTAL,
ports 6, 7,
9, P83,
PB4 to PB7,
D7 to D0
–0.3
—
VCC ×0.2
V
VCC < 4.0 V
0.8
V
VCC =
4.0 to 5.5 V
All output pins VOH
VCC – 0.5 —
—
V
IOH = –200 µA
VCC – 1.0 —
—
V
IOH = –1 mA
RES, STBY,
MD1, MD0
VIL
Note: * If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
363
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V*, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Output low
voltage
Symbol
Min
Typ
Max
Unit
Test Conditions
All output pins VOL
(except RESO)
—
—
0.4
V
IOL = 1.6 mA
Ports B,
A19 to A0
—
—
1.0
V
VCC ≤ 4 V
IOL = 5 mA,
4 V < VCC ≤ 5.5 V
IOL = 10 mA
RESO
—
—
0.4
V
IOL = 1.6 mA
—
—
1.0
µA
VIN = 0.5 to
VCC – 0.5 V
—
—
1.0
µA
VIN = 0.5 to
AVCC – 0.5 V
—
—
1.0
µA
VIN = 0.5 to
VCC – 0.5 V
—
—
10.0
µA
VIN = 0.5 to
VCC – 0.5 V
Input leakage STBY, NMI,
current
RES,
MD1, MD0
|IIN|
Port 7
Three-state
leakage
current
(off state)
Ports 6,
8 to B,
A19 to A0,
D7 to D0
RESO
|ITS1|
Note: * If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
364
Table 15-2 DC Characteristics (cont)
Conditions: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V*1, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Symbol
Min
Typ
Max
Unit Test Conditions
CIN
—
—
50
pF
—
—
15
VIN = 0 V
f = 1 MHz
Ta = 25°C
—
15
(3.0 V)
41.5
(5.5 V)
mA
f = 10 MHz
Sleep mode
—
10
(3.0 V)
30.5
(5.5 V)
mA
f = 10 MHz
Standby
mode*3
—
0.01
5.0
µA
Ta ≤ 50°C
—
—
20.0
µA
50°C < Ta
—
1.0
2.0
mA
AVCC = 3.0 V
—
1.2
—
mA
AVCC = 5.0 V
—
0.01
5.0
µA
—
0.2
0.4
mA
VREF = 3.0 V
—
0.3
—
mA
VREF = 5.0 V
—
0.01
5.0
µA
2.0
—
—
V
Input
capacitance
NMI
Current
dissipation*2
Normal
operation
All input pins
except NMI
Analog power During A/D
supply current conversion
ICC*4
AICC
Idle
Reference
current
During A/D
conversion
AICC
Idle
RAM standby voltage
VRAM
Notes: 1. If the A/D converter is not used, do not leave the AVCC, AVSS, and VREF pins open.
Connect AVCC and VREF to VCC, and connect AVSS to VSS.
2. Current dissipation values are for VIHmin = VCC – 0.5 V and VILmax = 0.5 V with all output
pins unloaded.
3. The values are for VRAM ≤ VCC < 3.0 V, VIHmin = VCC ×0.9, and VILmax = 0.3 V.
4. ICC depends on VCC and f as follows:
ICCmax = 3.0 (mA) + 0.7 (mA/MHz · V) ×VCC ×f [normal mode]
ICCmax = 3.0 (mA) + 0.5 (mA/MHz · V) ×VCC ×f [sleep mode]
365
Table 15-3 Permissible Output Currents
Conditions: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Item
Permissible output
low current (per pin)
Ports B, A19 to A0
Permissible output
low current (total)
Total of 28 pins including
ports B, A19 to A0
Symbol
Min
Typ
Max
Unit
IOL
—
—
10
mA
—
—
2.0
mA
—
—
80
mA
—
—
120
mA
Other output pins
ΣIOL
Total of all output pins,
including the above
Permissible output
high current (per pin)
All output pins
IOH
—
—
2.0
mA
Permissible output
high current (total)
Total of all output pins
ΣIOH
—
—
40
mA
Notes: 1. To protect chip reliability, do not exceed the output current values in table 15-3.
2. When driving a darlington pair or LED, always insert a current-limiting resistor in the
output line, as shown in figures 15-1 and 15-2.
366
H8/3004 and H8/3005
2 kΩ
Port
Darlington pair
Figure 15-1 Darlington Pair Drive Circuit (Example)
H8/3004 and H8/3005
Port B
600 Ω
LED
Figure 15-2 LED Drive Circuit (Example)
367
15.2.2 AC Characteristics
Bus timing parameters are listed in table 15-4. Control signal timing parameters are listed in
table 15-5. Timing parameters of the on-chip supporting modules are listed in table 15-6.
Table 15-4 Bus Timing
Condition A: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 8 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition B: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 10 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition C: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 16 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition A
Condition B
8 MHz
Item
Symbol
Min
Clock cycle time
tCYC
Clock low pulse width
tCL
Clock high pulse width
Clock rise time
Condition C
10 MHz
16 MHz
Max
Min
Max
Min
125
500
100
500
62.5
500
40
—
30
—
20
—
tCH
40
—
30
—
20
—
tCR
—
20
—
15
—
10
Clock fall time
tCF
—
20
—
15
—
10
Address delay time
tAD
—
60
—
50
—
30
Address hold time
tAH
25
—
20
—
10
—
Address strobe delay
time
tASD
—
60
—
40
—
30
Write strobe delay time
tWSD
—
60
—
50
—
30
Strobe delay time
tSD
—
60
—
50
—
30
Write data strobe pulse
width 1
tWSW1*
85
—
60
—
35
—
Write data strobe pulse
width 2
tWSW2*
150
—
110
—
65
—
Address setup time 1
tAS1
20
—
15
—
10
—
Address setup time 2
tAS2
80
—
65
—
40
—
Read data setup time
tRDS
50
—
35
—
20
—
Read data hold time
tRDH
0
—
0
—
0
—
368
Max
Unit
ns
Test
Conditions
Figure 15-4,
Figure 15-5
Table 15-4 Bus Timing (cont)
Condition A: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 8 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition B: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 10 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition C: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 16 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition A
Condition B
8 MHz
Item
Condition C
10 MHz
16 MHz
Symbol
Min
Max
Min
Max
Write data delay time
tWDD
—
75
—
75
—
60
Write data setup time 1
tWDS1
60
—
40
—
15
—
Write data setup time 2
tWDS2
5
—
–10
—
–5
—
Write data hold time
tWDH
25
—
20
—
20
—
Read data access
time 1
tACC1*
—
110
—
100
—
55
Read data access
time 2
tACC2*
—
230
—
200
—
115
Read data access
time 3
tACC3*
—
55
—
50
—
25
Read data access
time 4
tACC4*
—
160
—
150
—
85
Precharge time
tPCH*
85
—
60
—
40
—
Wait setup time
tWTS
40
—
40
—
25
—
Wait hold time
tWTH
10
—
10
—
5
—
Note is on next page.
369
Min
Max
Unit
Test
Conditions
ns
Figure 15-4,
Figure 15-5
ns
Figure 15-6
Note: At 8 MHz, the times below depend as indicated on the clock cycle time.
tACC1 = 1.5 ×tcyc – 78 (ns)
tWSW1 = 1.0 ×tcyc – 40 (ns)
tACC2 = 2.5 ×tcyc – 83 (ns)
tWSW2 = 1.5 ×tcyc – 38 (ns)
tACC3 = 1.0 ×tcyc – 70 (ns)
tPCH = 1.0 ×tcyc – 40 (ns)
tACC4 = 2.0 ×tcyc – 90 (ns)
At 10 MHz, the times below depend as indicated on the clock cycle time.
tACC1 = 1.5 ×tcyc – 50 (ns)
tWSW1 = 1.0 ×tcyc – 40 (ns)
tACC2 = 2.5 ×tcyc – 50 (ns)
tWSW2 = 1.5 ×tcyc – 40 (ns)
tACC3 = 1.0 ×tcyc – 50 (ns)
tPCH = 1.0 ×tcyc – 40 (ns)
tACC4 = 2.0 ×tcyc – 50 (ns)
At 16 MHz, the times below depend as indicated on the clock cycle time.
tACC1 = 1.5 ×tcyc – 39 (ns)
tWSW1 = 1.0 ×tcyc – 28 (ns)
tACC2 = 2.5 ×tcyc – 41 (ns)
tWSW2 = 1.5 ×tcyc – 28 (ns)
tACC3 = 1.0 ×tcyc – 38 (ns)
tPCH = 1.0 ×tcyc – 23 (ns)
tACC4 = 2.0 ×tcyc – 40 (ns)
370
Table 15-5 Control Signal Timing
Condition A: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = 0 V, ø = 2 MHz to 8 MHz, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Condition B: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 10 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition C: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 16 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition A
Condition B
8 MHz
Item
Condition C
10 MHz
16 MHz
Min
Max
Min
Max
Min
Max
RES setup time
tRESS
200
—
200
—
200
—
ns
RES pulse width
tRESW
10
—
10
—
10
—
tCYC
RESO output delay
time
tRESD
—
100
—
100
—
100
ns
RESO output pulse
width
tRESOW
132
—
132
—
132
—
tCYC
NMI setup time
(NMI, IRQ4 to IRQ0)
tNMIS
200
—
200
—
150
—
ns
Figure 15-9
NMI hold time
(NMI, IRQ4 to IRQ0)
tNMIH
10
—
10
—
10
—
Interrupt pulse width
(NMI, IRQ4 to IRQ0
when exiting software
standby mode)
tNMIW
200
—
200
—
200
—
Clock oscillator settling
time at reset (crystal)
tOSC1
20
—
20
—
20
—
ms
Figure 15-10
Clock oscillator settling
time in software standby
(crystal)
tOSC2
8
—
8
—
8
—
ms
Figure 14-1
371
Unit
Test
Conditions
Symbol
Figure 15-7
Figure 15-8
Table 15-6 Timing of On-Chip Supporting Modules
Condition A: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 8 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition B: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = 0 V, ø = 2 MHz to 10 MHz, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Condition C: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 16 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition A
Condition B
8 MHz
SCI
10 MHz
16 MHz
Symbol
Min
Max
Min
Max
Min
Max
Unit
Test
Conditions
Timer output
delay time
tTOCD
—
100
—
100
—
100
ns
Figure 15-12
Timer input
setup time
tTICS
50
—
50
—
50
—
Timer clock
input setup time
tTCKS
50
—
50
—
50
—
Timer
clock
pulse
width
Single
edge
tTCKWH
1.5
—
1.5
—
1.5
—
Both
edges
tTCKWL
2.5
—
2.5
—
2.5
—
tSCYC
4
—
4
—
4
—
tSCYC
6
—
6
—
6
—
Input clock rise
time
tSCKr
—
1.5
—
1.5
—
1.5
Input clock fall
time
tSCKf
—
1.5
—
1.5
—
1.5
Input clock
pulse width
tSCKW
0.4
0.6
0.4
0.6
0.4
0.6
Item
ITU
Condition C
Input Asynclock chronous
cycle Synchronous
372
Figure 15-13
tCYC
Figure 15-14
tSCYC
Table 15-6 Timing of On-Chip Supporting Modules (cont)
Condition A: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = 0 V, ø = 2 MHz to 8 MHz, Ta = –20°C to +75°C (regular specifications),
Ta = –40°C to +85°C (wide-range specifications)
Condition B: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 10 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition C: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 16 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Ports
Condition B
Condition C
8 MHz
10 MHz
16 MHz
Symbol
Min
Max
Min
Max
Min
Max
Unit
Test
Conditions
Transmit data
delay time
tTXD
—
100
—
100
—
100
ns
Figure 15-15
Receive data
setup time
(synchronous)
tRXS
100
—
100
—
100
—
Receive data
hold time
(synchronous
clock input)
tRXH
100
—
100
—
100
—
Receive data
hold time
(synchronous
clock output)
tRXH
0
—
0
—
0
—
Output data
delay time
tPWD
—
100
—
100
—
100
ns
Figure 15-11
Input data
setup time
(synchronous)
tPRS
50
—
50
—
50
—
Input data
hold time
(synchronous)
tPRH
50
—
50
—
50
—
Item
SCI
Condition A
373
5V
RL
H8/3004 and
H8/3005
output pin
C = 90 pF: ports 6, 8, A19 to A0,
D7 to D0, ø, AS, RD,
WR
C = 30 pF: ports 9, A, B
R L = 2.4 kΩ
R H = 12 kΩ
C
RH
Input/output timing measurement levels
• Low: 0.8 V
• High: 2.0 V
Figure 15-3 Output Load Circuit
374
15.2.3 A/D Conversion Characteristics
Table 15-7 lists the A/D conversion characteristics.
Table 15-7 A/D Converter Characteristics
Condition A: VCC = 2.7 V to 5.5 V, AVCC = 2.7 V to 5.5 V, VREF = 2.7 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 8 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition B: VCC = 3.0 V to 5.5 V, AVCC = 3.0 V to 5.5 V, VREF = 3.0 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 10 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition C: VCC = 5.0 V ± 10%, AVCC = 5.0 V ± 10%, VREF = 4.5 V to AVCC,
VSS = AVSS = 0 V, ø = 2 MHz to 16 MHz, Ta = –20°C to +75°C (regular
specifications), Ta = –40°C to +85°C (wide-range specifications)
Condition A
Condition B
Condition C
8 MHz
10 MHz
16 MHz
Item
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
Resolution
10
10
10
10
10
10
10
10
10
bits
Conversion time
—
—
16.8
—
—
13.4
—
—
8.4
µs
Analog input
capacitance
—
—
20
—
—
20
—
—
20
pF
Permissible signalsource impedance
—
—
10*1
—
—
10*1
—
—
10*4
kΩ
—
—
5*2
5*3
—
—
5*5
Nonlinearity error
—
—
±6.0
—
—
±6.0
—
—
±3.0
LSB
Offset error
—
—
±4.0
—
—
±4.0
—
—
±2.0
LSB
Full-scale error
—
—
±4.0
—
—
±4.0
—
—
±2.0
LSB
Quantization error
—
—
±0.5
—
—
±0.5
—
—
±0.5
LSB
Absolute accuracy
—
—
±8.0
—
—
±8.0
—
—
±4.0
LSB
Notes: 1.
2.
3.
4.
5.
The value is for 4.0 ≤ AVCC ≤ 5.5.
The value is for 2.7 ≤ AVCC < 4.0.
The value is for 3.0 ≤ AVCC < 4.0.
The value is for ø ≤ 12 MHz.
The value is for ø > 12 MHz.
375
15.3 Operational Timing
This section shows timing diagrams.
15.3.1 Bus Timing
Bus timing is shown as follows:
•
Basic bus cycle: two-state access
Figure 15-4 shows the timing of the external two-state access cycle.
•
Basic bus cycle: three-state access
Figure 15-5 shows the timing of the external three-state access cycle.
•
Basic bus cycle: three-state access with one wait state
Figure 15-6 shows the timing of the external three-state access cycle with one wait state
inserted.
376
T1
T2
tcyc
tCH
tCL
ø
tCF
tCR
tAD
A19 to A 0
tPCH
AS
tASD
tACC3
tSD
tAH
tASD
tACC3
tSD
tAH
tAS1
tPCH
RD
(read)
tAS1
tACC1
tRDS
tRDH
D7 to D0
(read)
tPCH
tASD
WR (write)
tSD
tAH
tAS1
tWSW1
tWDD
tWDS1
tWDH
D7 to D0
(write)
Figure 15-4 Basic Bus Cycle: Two-State Access
377
T1
T2
T3
ø
A19 to A0
tACC4
AS
tACC4
RD (read)
tRDS
tACC2
D7 to D0
(read)
tWSD
WR (write)
tWSW2
tAS2
tWDS2
D7 to D0
(write)
Figure 15-5 Basic Bus Cycle: Three-State Access
378
T1
T2
TW
T3
ø
A19 to A0
AS
RD (read)
D7 to D0
(read)
WR (write)
D7 to D0
(write)
tWTS
tWTH
tWTS
tWTH
WAIT
Figure 15-6 Basic Bus Cycle: Three-State Access with One Wait State
379
15.3.2 Control Signal Timing
Control signal timing is shown as follows:
•
Reset input timing
Figure 15-7 shows the reset input timing.
•
Reset output timing
Figure 15-8 shows the reset output timing.
•
Interrupt input timing
Figure 15-9 shows the input timing for NMI and IRQ4 to IRQ0.
ø
tRESS
tRESS
RES
tRESW
Figure 15-7 Reset Input Timing
ø
tRESD
tRESD
RESO
tRESOW
Figure 15-8 Reset Output Timing
380
ø
tNMIS
tNMIH
tNMIS
tNMIH
NMI
IRQ E
tNMIS
IRQ L
IRQ E : Edge-sensitive IRQ I
IRQ L : Level-sensitive IRQ I (I = 0 to 4)
tNMIW
NMI
IRQ J
(J = 0 to 2)
Figure 15-9 Interrupt Input Timing
381
15.3.3 Clock Timing
Clock timing is shown as follows:
•
Oscillator settling timing
Figure 15-10 shows the oscillator settling timing.
ø
VCC
STBY
tOSC1
tOSC1
RES
Figure 15-10 Oscillator Settling Timing
15.3.4 I/O Port Timing
I/O port timing is shown as follows.
T1
T2
T3
ø
tPRS
tPRH
Ports 6 to B
(read)
tPWD
Ports 6,
8 to B (write)
Figure 15-11 I/O Port Input/Output Timing
382
15.3.5 ITU Timing
ITU timing is shown as follows:
•
ITU input/output timing
Figure 15-12 shows the ITU input/output timing.
•
ITU external clock input timing
Figure 15-13 shows the ITU external clock input timing.
ø
tTOCD
Output
compare*1
tTICS
Input
capture*2
Notes: 1. TIOCA0 to TIOCA4, TIOCB0 to TIOCB4, TOCXA4, TOCXB4
2. TIOCA0 to TIOCA4, TIOCB0 to TIOCB4
Figure 15-12 ITU Input/Output Timing
tTCKS
ø
tTCKS
TCLKA to
TCLKD
tTCKWL
tTCKWH
Figure 15-13 ITU Clock Input Timing
383
15.3.6 SCI Input/Output Timing
SCI timing is shown as follows:
•
SCI input clock timing
Figure 15-14 shows the SCI input clock timing.
•
SCI input/output timing (synchronous mode)
Figure 15-15 shows the SCI input/output timing in synchronous mode.
tSCKW
tSCKr
tSCKf
SCK
tSCYC
Figure 15-14 SCK Input Clock Timing
tSCYC
SCK
tTXD
TxD
(transmit
data)
tRXS
tRXH
RxD
(receive
data)
Figure 15-15 SCI Input/Output Timing in Synchronous Mode
384
Appendix A Instruction Set
A.1 Instruction List
Operand Notation
Symbol
Description
Rd
General destination register
Rs
General source register
Rn
General register
ERd
General destination register (address register or 32-bit register)
ERs
General source register (address register or 32-bit register)
ERn
General register (32-bit register)
(EAd)
Destination operand
(EAs)
Source operand
PC
Program counter
SP
Stack pointer
CCR
Condition code register
N
N (negative) flag in CCR
Z
Z (zero) flag in CCR
V
V (overflow) flag in CCR
C
C (carry) flag in CCR
disp
Displacement
→
Transfer from the operand on the left to the operand on the right, or transition from
the state on the left to the state on the right
+
Addition of the operands on both sides
–
Subtraction of the operand on the right from the operand on the left
×
Multiplication of the operands on both sides
÷
Division of the operand on the left by the operand on the right
∧
Logical AND of the operands on both sides
∨
Logical OR of the operands on both sides
⊕
Exclusive logical OR of the operands on both sides
¬
NOT (logical complement)
( ), < >
Contents of operand
Note: General registers include 8-bit registers (R0H to R7H and R0L to R7L) and 16-bit registers
(R0 to R7 and E0 to E7).
385
Condition Code Notation
Symbol
Description
↕
Changed according to execution result
*
Undetermined (no guaranteed value)
0
Cleared to 0
1
Set to 1
—
Not affected by execution of the instruction
∆
Varies depending on conditions, described in notes
386
Table A-1 Instruction Set
Data transfer instructions
Condition Code
I
C
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
2
@(d, ERn)
#xx:8 →Rd8
@ERn
Operation
B
Rn
MOV.B #xx:8, Rd
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
1.
H N
Z
V
— — ↕
↕
0 —
2
— — ↕
↕
0 —
2
— — ↕
↕
0 —
4
MOV.B Rs, Rd
B
Rs8 →Rd8
MOV.B @ERs, Rd
B
@ERs →Rd8
MOV.B @(d:16, ERs),
Rd
B
@(d:16, ERs) →Rd8
4
— — ↕
↕
0 —
6
MOV.B @(d:24, ERs),
Rd
B
@(d:24, ERs) →Rd8
8
— — ↕
↕
0 —
10
MOV.B @ERs+, Rd
B
@ERs →Rd8
ERs32+1 →ERs32
— — ↕
↕
0 —
6
MOV.B @aa:8, Rd
B
@aa:8 →Rd8
2
— — ↕
↕
0 —
4
MOV.B @aa:16, Rd
B
@aa:16 →Rd8
4
— — ↕
↕
0 —
6
MOV.B @aa:24, Rd
B
@aa:24 →Rd8
6
— — ↕
↕
0 —
8
MOV.B Rs, @ERd
B
Rs8 →@ERd
— — ↕
↕
0 —
4
MOV.B Rs, @(d:16,
ERd)
B
Rs8 →@(d:16, ERd)
4
— — ↕
↕
0 —
6
MOV.B Rs, @(d:24,
ERd)
B
Rs8 →@(d:24, ERd)
8
— — ↕
↕
0 —
10
MOV.B Rs, @ERd
B
ERd32–1 →ERd32
Rs8 →@ERd
— — ↕
↕
0 —
6
MOV.B Rs, @aa:8
B
Rs8 →@aa:8
2
— — ↕
↕
0 —
4
MOV.B Rs, @aa:16
B
Rs8 →@aa:16
4
— — ↕
↕
0 —
6
MOV.B Rs, @aa:24
B
Rs8 →@aa:24
MOV.W #xx:16, Rd
W #xx:16 →Rd16
MOV.W Rs, Rd
W Rs16 →Rd16
MOV.W @ERs, Rd
W @ERs →Rd16
MOV.W @(d:16, ERs),
Rd
W @(d:16, ERs) →Rd16
MOV.W @(d:24, ERs),
Rd
W @(d:24, ERs) →Rd16
MOV.W @ERs+, Rd
W @ERs →Rd16
ERs32+2 →@ERd32
MOV.W @aa:16, Rd
W @aa:16 →Rd16
2
2
2
2
2
— — ↕
↕
0 —
8
— — ↕
↕
0 —
4
— — ↕
↕
0 —
2
— — ↕
↕
0 —
4
4
— — ↕
↕
0 —
6
8
— — ↕
↕
0 —
10
— — ↕
↕
0 —
6
— — ↕
↕
0 —
6
6
4
2
2
2
4
387
Table A-1 Instruction Set (cont)
W Rs16 →@aa:16
MOV.W Rs, @aa:24
W Rs16 →@aa:24
MOV.L #xx:32, Rd
L
#xx:32 →Rd32
MOV.L ERs, ERd
L
ERs32 →ERd32
H N
Z
V
C
Advanced
MOV.W Rs, @aa:16
Condition Code
I
Normal
W ERd32–2 →ERd32
Rs16 →@ERd
No. of
States *1
Implied
MOV.W Rs, @–ERd
@@aa
W Rs16 →@(d:24, ERd)
@(d, PC)
MOV.W Rs, @(d:24,
ERd)
@aa
W Rs16 →@(d:16, ERd)
@–ERn/@ERn+
MOV.W Rs, @(d:16,
ERd)
@(d, ERn)
W Rs16 →@ERd
@ERn
W @aa:24 →Rd16
MOV.W Rs, @ERd
Rn
MOV.W @aa:24, Rd
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
— — ↕
↕
0 —
8
— — ↕
↕
0 —
4
4
— — ↕
↕
0 —
6
8
— — ↕
↕
0 —
8
— — ↕
↕
0 —
6
4
— — ↕
↕
0 —
6
6
— — ↕
↕
0 —
8
— — ↕
↕
0 —
8
— — ↕
↕
0 —
2
6
2
2
6
2
MOV.L @ERs, ERd
L
@ERs →ERd32
— — ↕
↕
0 —
8
MOV.L @(d:16, ERs),
ERd
L
@(d:16, ERs) →ERd32
6
— — ↕
↕
0 —
10
MOV.L @(d:24, ERs),
ERd
L
@(d:24, ERs) →ERd32
10
— — ↕
↕
0 —
14
MOV.L @ERs+, ERd
L
@ERs →ERd32
ERs32+4 →ERs32
— — ↕
↕
0 —
10
MOV.L @aa:16, ERd
L
@aa:16 →ERd32
6
— — ↕
↕
0 —
10
MOV.L @aa:24, ERd
L
@aa:24 →ERd32
8
— — ↕
↕
0 —
12
MOV.L ERs, @ERd
L
ERs32 →@ERd
— — ↕
↕
0 —
8
MOV.L ERs, @(d:16,
ERd)
L
ERs32 →@(d:16, ERd)
6
— — ↕
↕
0 —
10
MOV.L ERs, @(d:24,
ERd)
L
ERs32 →@(d:24, ERd)
10
— — ↕
↕
0 —
14
MOV.L ERs, @–ERd
L
ERd32–4 →ERd32
ERs32 →@ERd
— — ↕
↕
0 —
10
4
4
4
4
MOV.L ERs, @aa:16
L
ERs32 →@aa:16
6
— — ↕
↕
0 —
10
MOV.L ERs, @aa:24
L
ERs32 →@aa:24
8
— — ↕
↕
0 —
12
POP.W Rn
W @SP →Rn16
SP+2 →SP
2 — — ↕
↕
0 —
6
POP.L ERn
L
4 — — ↕
↕
0 —
8
@SP →ERn32
SP+4 →SP
388
Table A-1 Instruction Set (cont)
C
Normal
Condition Code
I
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
H N
Z
V
2 — — ↕
↕
0 —
6
4 — — ↕
↕
0 —
8
PUSH.W Rn
W SP–2 →SP
Rn16 →@SP
PUSH.L ERn
L
SP–4 →SP
ERn32 →@SP
MOVFPE @aa:16,
Rd
B
Cannot be used in the
H8/3004 and H8/3005
4
Cannot be used in the H8/3004
and H8/3005
MOVTPE Rs,
@aa:16
B
Cannot be used in the
H8/3004 and H8/3005
4
Cannot be used in the H8/3004
and H8/3005
Arithmetic instructions
B
W Rd16+#xx:16 →Rd16
ADD.W Rs, Rd
W Rd16+Rs16 →Rd16
ADD.L #xx:32, ERd
L
ERd32+#xx:32 →
ERd32
ADD.L ERs, ERd
L
ERd32+ERs32 →
ERd32
ADDX.B #xx:8, Rd
B
Rd8+#xx:8 +C →Rd8
ADDX.B Rs, Rd
B
Rd8+Rs8 +C →Rd8
ADDS.L #1, ERd
L
ERd32+1 →ERd32
ADDS.L #2, ERd
L
ADDS.L #4, ERd
L
INC.B Rd
B
INC.W #1, Rd
W Rd16+1 →Rd16
INC.W #2, Rd
W Rd16+2 →Rd16
2
4
Condition Code
I
H N
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
Rd8+Rs8 →Rd8
ADD.B Rs, Rd
ADD.W #xx:16, Rd
@aa
2
@–ERn/@ERn+
Rd8+#xx:8 →Rd8
@(d, ERn)
#xx
B
@ERn
Operation
ADD.B #xx:8, Rd
Rn
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
2.
Z
V
C
— ↕
↕
↕
↕
↕
2
— ↕
↕
↕
↕
↕
2
— (1) ↕
↕
↕
↕
4
— (1) ↕
↕
↕
↕
2
— (2) ↕
↕
↕
↕
6
— (2) ↕
↕
↕
↕
2
— ↕
↕ (3) ↕
↕
2
2
— ↕
↕ (3) ↕
↕
2
2
— — — — — —
2
ERd32+2 →ERd32
2
— — — — — —
2
ERd32+4 →ERd32
2
— — — — — —
2
Rd8+1 →Rd8
2
— — ↕
↕
↕ —
2
2
— — ↕
↕
↕ —
2
2
— — ↕
↕
↕ —
2
2
6
2
2
389
TIable A-1 Instruction Set (cont)
H N
Z
V
C
Normal
Condition Code
I
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
INC.L #1, ERd
L
ERd32+1 →ERd32
2
— — ↕
↕
↕ —
2
INC.L #2, ERd
L
ERd32+2 →ERd32
2
— — ↕
↕
↕ —
2
DAA Rd
B
Rd8 decimal adjust
→Rd8
2
— *
↕
↕
* —
2
SUB.B Rs, Rd
B
Rd8–Rs8 →Rd8
2
— ↕
SUB.W #xx:16, Rd
W Rd16–#xx:16 →Rd16
SUB.W Rs, Rd
W Rd16–Rs16 →Rd16
SUB.L #xx:32, ERd
L
ERd32–#xx:32
→ERd32
SUB.L ERs, ERd
L
ERd32–ERs32
→ERd32
SUBX.B #xx:8, Rd
B
Rd8–#xx:8–C →Rd8
SUBX.B Rs, Rd
B
Rd8–Rs8–C →Rd8
SUBS.L #1, ERd
L
ERd32–1 →ERd32
SUBS.L #2, ERd
L
SUBS.L #4, ERd
L
↕
↕
↕
↕
2
— (1) ↕
↕
↕
↕
4
— (1) ↕
↕
↕
↕
2
— (2) ↕
↕
↕
↕
6
— (2) ↕
↕
↕
↕
2
— ↕
↕ (3) ↕
↕
2
2
— ↕
↕ (3) ↕
↕
2
2
— — — — — —
2
ERd32–2 →ERd32
2
— — — — — —
2
ERd32–4 →ERd32
2
— — — — — —
2
Rd8–1 →Rd8
4
2
6
2
2
DEC.B Rd
B
2
— — ↕
↕
↕ —
2
DEC.W #1, Rd
W Rd16–1 →Rd16
2
— — ↕
↕
↕ —
2
DEC.W #2, Rd
W Rd16–2 →Rd16
2
— — ↕
↕
↕ —
2
DEC.L #1, ERd
L
2
— — ↕
↕
↕ —
2
ERd32–1 →ERd32
DEC.L #2, ERd
L
ERd32–2 →ERd32
2
— — ↕
↕
↕ —
2
DAS.Rd
B
Rd8 decimal adjust
→Rd8
2
— *
↕
↕
* —
2
MULXU. B Rs, Rd
B
Rd8 ×Rs8 →Rd16
(unsigned multiplication)
2
— — — — — —
14
MULXU. W Rs, ERd
W Rd16 ×Rs16 →ERd32
(unsigned multiplication)
2
— — — — — —
22
MULXS. B Rs, Rd
B
Rd8 ×Rs8 →Rd16
(signed multiplication)
4
— — ↕
↕ — —
16
MULXS. W Rs, ERd
W Rd16 ×Rs16 →ERd32
(signed multiplication)
4
— — ↕
↕ — —
24
DIVXU. B Rs, Rd
B
2
— — (6) (7) — —
14
Rd16 ÷ Rs8 →Rd16
(RdH: remainder,
RdL: quotient)
(unsigned division)
390
Table A-1 Instruction Set (cont)
H N
Z
V
C
Normal
Condition Code
I
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
DIVXU. W Rs, ERd
W ERd32 ÷ Rs16 →
ERd32
(Ed: remainder,
Rd: quotient)
(unsigned division)
2
— — (6) (7) — —
22
DIVXS. B Rs, Rd
B
Rd16 ÷ Rs8 →Rd16
(RdH: remainder,
RdL: quotient)
(signed division)
4
— — (8) (7) — —
16
DIVXS. W Rs, ERd
W ERd32 ÷ Rs16 →ERd32
(Ed: remainder,
Rd: quotient)
(signed division)
4
— — (8) (7) — —
24
CMP.B #xx:8, Rd
B
Rd8–#xx:8
CMP.B Rs, Rd
B
Rd8–Rs8
CMP.W #xx:16, Rd
W Rd16–#xx:16
CMP.W Rs, Rd
W Rd16–Rs16
CMP.L #xx:32, ERd
L
ERd32–#xx:32
CMP.L ERs, ERd
L
ERd32–ERs32
NEG.B Rd
B
0–Rd8 →Rd8
NEG.W Rd
W 0–Rd16 →Rd16
— ↕
↕
↕
↕
↕
2
2
— ↕
↕
↕
↕
↕
2
— (1) ↕
↕
↕
↕
4
2
— (1) ↕
↕
↕
↕
2
— (2) ↕
↕
↕
↕
4
2
— (2) ↕
↕
↕
↕
2
2
4
6
2
— ↕
↕
↕
↕
↕
2
2
— ↕
↕
↕
↕
↕
2
NEG.L ERd
L
0–ERd32 →ERd32
2
— ↕
↕
↕
↕
↕
2
EXTU.W Rd
W 0 →(<bits 15 to 8>
of Rd16)
2
— — 0
↕
0 —
2
EXTU.L ERd
L
0 →(<bits 31 to 16>
of ERd32)
2
— — 0
↕
0 —
2
EXTS.W Rd
W (<bit 7> of Rd16) →
(<bits 15 to 8> of Rd16)
2
— — ↕
↕
0 —
2
EXTS.L ERd
L
2
— — ↕
↕
0 —
2
(<bit 15> of ERd32) →
(<bits 31 to 16> of
ERd32)
391
Table A-1 Instruction Set (cont)
Logic instructions
W Rd16∧Rs16 →Rd16
L
ERd32∧#xx:32 →ERd32
AND.L ERs, ERd
L
ERd32∧ERs32 →ERd32
OR.B #xx:8, Rd
B
Rd8∨#xx:8 →Rd8
Rd8∨Rs8 →Rd8
OR.B Rs, Rd
B
OR.W #xx:16, Rd
W Rd16∨#xx:16 →Rd16
OR.W Rs, Rd
W Rd16∨Rs16 →Rd16
OR.L #xx:32, ERd
L
ERd32∨#xx:32 →ERd32
OR.L ERs, ERd
L
ERd32∨ERs32 →ERd32
XOR.B #xx:8, Rd
B
Rd8⊕#xx:8 →Rd8
Rd8⊕Rs8 →Rd8
XOR.B Rs, Rd
B
XOR.W #xx:16, Rd
W Rd16⊕#xx:16 →Rd16
XOR.W Rs, Rd
W Rd16⊕Rs16 →Rd16
XOR.L #xx:32, ERd
L
ERd32⊕#xx:32 →ERd32
2
6
4
2
2
4
2
6
4
2
2
4
2
6
Condition Code
I
C
Advanced
AND.W Rs, Rd
AND.L #xx:32, ERd
2
4
No. of
States *1
Implied
Rd8∧Rs8 →Rd8
W Rd16∧#xx:16 →Rd16
@@aa
B
AND.W #xx:16, Rd
@(d, PC)
AND.B Rs, Rd
@aa
2
@–ERn/@ERn+
Rd8∧#xx:8 →Rd8
@(d, ERn)
#xx
B
@ERn
Operation
AND.B #xx:8, Rd
Rn
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
3.
H N
Z
V
— — ↕
↕
0 —
2
— — ↕
↕
0 —
2
— — ↕
↕
0 —
4
— — ↕
↕
0 —
2
— — ↕
↕
0 —
6
— — ↕
↕
0 —
4
— — ↕
↕
0 —
2
— — ↕
↕
0 —
2
— — ↕
↕
0 —
4
— — ↕
↕
0 —
2
— — ↕
↕
0 —
6
— — ↕
↕
0 —
4
— — ↕
↕
0 —
2
— — ↕
↕
0 —
2
— — ↕
↕
0 —
4
— — ↕
↕
0 —
2
— — ↕
↕
0 —
6
XOR.L ERs, ERd
L
ERd32⊕ERs32 →ERd32
4
— — ↕
↕
0 —
4
NOT.B Rd
B
¬ Rd8 →Rd8
2
— — ↕
↕
0 —
2
NOT.W Rd
W ¬ Rd16 →Rd16
2
— — ↕
↕
0 —
2
NOT.L ERd
L
¬ Rd32 →Rd32
2
— — ↕
↕
0 —
2
392
Table A-1 Instruction Set (cont)
Shift instructions
SHAL.W Rd
W
SHAL.L ERd
L
SHAR.B Rd
B
SHAR.W Rd
W
SHAR.L ERd
L
SHLL.B Rd
B
SHLL.W Rd
W
SHLL.L ERd
L
SHLR.B Rd
B
SHLR.W Rd
W
SHLR.L ERd
L
ROTXL.B Rd
B
ROTXL.W Rd
W
ROTXL.L ERd
L
ROTXR.B Rd
B
ROTXR.W Rd
W
ROTXR.L ERd
L
ROTL.B Rd
B
ROTL.W Rd
W
ROTL.L ERd
L
ROTR.B Rd
B
ROTR.W Rd
W
ROTR.L ERd
L
2
C
0
MSB
LSB
C
MSB
LSB
C
0
MSB
LSB
0
C
MSB
LSB
C
MSB
LSB
C
MSB
LSB
C
MSB
LSB
C
MSB
LSB
Condition Code
H N
Z
V
C
— — ↕
I
↕
↕
↕
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
Operation
@ERn
B
Rn
SHAL.B Rd
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
4.
2
2
— — ↕
↕
↕
↕
2
2
— — ↕
↕
↕
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
2
— — ↕
↕
0
↕
2
393
Table A-1 Instruction Set (cont)
Bit manipulation instructions
BSET #xx:3, @ERd
B
(#xx:3 of @ERd) ←1
BSET #xx:3, @aa:8
B
(#xx:3 of @aa:8) ←1
BSET Rn, Rd
B
(Rn8 of Rd8) ←1
BSET Rn, @ERd
B
(Rn8 of @ERd) ←1
BSET Rn, @aa:8
B
(Rn8 of @aa:8) ←1
BCLR #xx:3, Rd
B
(#xx:3 of Rd8) ←0
BCLR #xx:3, @ERd
B
(#xx:3 of @ERd) ←0
BCLR #xx:3, @aa:8
B
(#xx:3 of @aa:8) ←0
BCLR Rn, Rd
B
(Rn8 of Rd8) ←0
BCLR Rn, @ERd
B
(Rn8 of @ERd) ←0
BCLR Rn, @aa:8
B
(Rn8 of @aa:8) ←0
BNOT #xx:3, Rd
B
(#xx:3 of Rd8) ←
¬ (#xx:3 of Rd8)
BNOT #xx:3, @ERd
B
(#xx:3 of @ERd) ←
¬ (#xx:3 of @ERd)
BNOT #xx:3, @aa:8
B
(#xx:3 of @aa:8) ←
¬ (#xx:3 of @aa:8)
BNOT Rn, Rd
B
(Rn8 of Rd8) ←
¬ (Rn8 of Rd8)
BNOT Rn, @ERd
B
(Rn8 of @ERd) ←
¬ (Rn8 of @ERd)
BNOT Rn, @aa:8
B
(Rn8 of @aa:8) ←
¬ (Rn8 of @aa:8)
BTST #xx:3, Rd
B
¬ (#xx:3 of Rd8) →Z
BTST #xx:3, @ERd
B
¬ (#xx:3 of @ERd) →Z
BTST #xx:3, @aa:8
B
¬ (#xx:3 of @aa:8) →Z
BTST Rn, Rd
B
¬ (Rn8 of @Rd8) →Z
BTST Rn, @ERd
B
¬ (Rn8 of @ERd) →Z
BTST Rn, @aa:8
B
¬ (Rn8 of @aa:8) →Z
BLD #xx:3, Rd
B
(#xx:3 of Rd8) →C
2
Condition Code
I
H N
Z
V
C
— — — — — —
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
394
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
(#xx:3 of Rd8) ←1
@ERn
B
Rn
Operation
BSET #xx:3, Rd
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
5.
2
— — — — — —
8
— — — — — —
8
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — ↕ — —
2
— — — ↕ — —
6
— — — ↕ — —
6
— — — ↕ — —
2
— — — ↕ — —
6
— — — ↕ — —
6
— — — — — ↕
2
Table A-1 Instruction Set (cont)
BLD #xx:3, @ERd
B
(#xx:3 of @ERd) →C
BLD #xx:3, @aa:8
B
(#xx:3 of @aa:8) →C
BILD #xx:3, Rd
B
¬ (#xx:3 of Rd8) →C
BILD #xx:3, @ERd
B
¬ (#xx:3 of @ERd) →C
BILD #xx:3, @aa:8
B
¬ (#xx:3 of @aa:8) →C
BST #xx:3, Rd
B
C →(#xx:3 of Rd8)
BST #xx:3, @ERd
B
C →(#xx:3 of @ERd24)
BST #xx:3, @aa:8
B
C →(#xx:3 of @aa:8)
BIST #xx:3, Rd
B
¬ C →(#xx:3 of Rd8)
BIST #xx:3, @ERd
B
¬ C →(#xx:3 of @ERd24)
BIST #xx:3, @aa:8
B
¬ C →(#xx:3 of @aa:8)
BAND #xx:3, Rd
B
C∧(#xx:3 of Rd8) →C
BAND #xx:3, @ERd
B
C∧(#xx:3 of @ERd24) →C
BAND #xx:3, @aa:8
B
C∧(#xx:3 of @aa:8) →C
BIAND #xx:3, Rd
B
C∧¬ (#xx:3 of Rd8) →C
BIAND #xx:3, @ERd
B
C∧¬ (#xx:3 of @ERd24) →C
BIAND #xx:3, @aa:8
B
C∧¬ (#xx:3 of @aa:8) →C
BOR #xx:3, Rd
B
C∨(#xx:3 of Rd8) →C
BOR #xx:3, @ERd
B
C∨(#xx:3 of @ERd24) →C
BOR #xx:3, @aa:8
B
C∨(#xx:3 of @aa:8) →C
BIOR #xx:3, Rd
B
C∨¬ (#xx:3 of Rd8) →C
BIOR #xx:3, @ERd
B
C∨¬ (#xx:3 of @ERd24) →C
BIOR #xx:3, @aa:8
B
C∨¬ (#xx:3 of @aa:8) →C
BXOR #xx:3, Rd
B
C⊕(#xx:3 of Rd8) →C
BXOR #xx:3, @ERd
B
C⊕(#xx:3 of @ERd24) →C
BXOR #xx:3, @aa:8
B
C⊕(#xx:3 of @aa:8) →C
BIXOR #xx:3, Rd
B
C⊕¬ (#xx:3 of Rd8) →C
BIXOR #xx:3, @ERd
B
C⊕¬ (#xx:3 of @ERd24) →C
BIXOR #xx:3, @aa:8
B
C⊕¬ (#xx:3 of @aa:8) →C
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
395
H N
Z
V
C
Normal
Condition Code
I
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
— — — — — ↕
6
— — — — — ↕
6
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — — — —
2
— — — — — —
8
— — — — — —
8
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
— — — — — ↕
2
— — — — — ↕
6
— — — — — ↕
6
Table A-1 Instruction Set (cont)
Branching instructions
BRN d:16 (BF d:16)
—
BHI d:8
—
BHI d:16
—
BLS d:8
—
BLS d:16
—
BCC d:8 (BHS d:8)
—
BCC d:16 (BHS d:16)
—
BCS d:8 (BLO d:8)
—
BCS d:16 (BLO d:16)
—
BNE d:8
—
BNE d:16
—
BEQ d:8
—
BEQ d:16
—
BVC d:8
—
BVC d:16
—
BVS d:8
—
BVS d:16
—
BPL d:8
—
BPL d:16
—
BMI d:8
—
BMI d:16
—
BGE d:8
—
BGE d:16
—
BLT d:8
—
BLT d:16
—
BGT d:8
—
BGT d:16
—
C ∨Z = 0
C ∨Z = 1
C=0
C=1
Z=0
Z=1
V=0
V=1
N=0
N=1
N⊕V = 0
N⊕V = 1
Z ∨(N⊕V) =
0
396
Condition Code
I
H N
Z
V
C
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
—
If condition
is true then
PC ←PC+d
Never
else next;
@–ERn/@ERn+
—
BRN d:8 (BF d:8)
Always
@(d, ERn)
BRA d:16 (BT d:16)
Operation
@ERn
—
Rn
BRA d:8 (BT d:8)
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
6.
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
2
— — — — — —
4
4
— — — — — —
6
Table A-1 Instruction Set (cont)
BLE d:8
—
BLE d:16
—
If condition
is true then
PC ←PC+d
else next;
Z ∨(N⊕V)
=1
H N
Z
V
C
Normal
Condition Code
I
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Operation
Rn
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
2
— — — — — —
4
4
— — — — — —
6
JMP @ERn
— PC ←ERn
JMP @aa:24
— PC ←aa:24
JMP @@aa:8
— PC ←@aa:8
— — — — — —
8
10
BSR d:8
— PC →@–SP
PC ←PC+d:8
2
— — — — — —
6
8
BSR d:16
— PC →@–SP
PC ←PC+d:16
4
— — — — — —
8
10
JSR @ERn
— PC →@–SP
PC ←@ERn
— — — — — —
6
8
JSR @aa:24
— PC →@–SP
PC ←@aa:24
— — — — — —
8
10
JSR @@aa:8
— PC →@–SP
PC ←@aa:8
— — — — — —
8
12
RTS
— PC ←@SP+
2 — — — — — —
8
10
2
4
2
2
4
2
397
— — — — — —
4
— — — — — —
6
Table A-1 Instruction Set (cont)
7.
System control instructions
C
Normal
Advanced
No. of
States *1
2 — — — — — —
14
16
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Condition Code
I
H N
Z
V
TRAPA #x:2
— PC →@–SP
CCR →@–SP
<vector> →PC
RTE
— CCR ←@SP+
PC ←@SP+
↕
↕
10
SLEEP
— Transition to powerdown state
— — — — — —
2
↕
↕
↕
↕
↕
↕
2
↕
↕
↕
↕
↕
↕
2
↕
↕
↕
↕
LDC #xx:8, CCR
B
#xx:8 →CCR
LDC Rs, CCR
B
Rs8 →CCR
LDC @ERs, CCR
W @ERs →CCR
↕
↕
↕
↕
↕
↕
6
LDC @(d:16, ERs),
CCR
W @(d:16, ERs) →CCR
6
↕
↕
↕
↕
↕
↕
8
LDC @(d:24, ERs),
CCR
W @(d:24, ERs) →CCR
10
↕
↕
↕
↕
↕
↕
12
LDC @ERs+, CCR
W @ERs →CCR
ERs32+2 →ERs32
↕
↕
↕
↕
↕
↕
8
LDC @aa:16, CCR
W @aa:16 →CCR
↕
↕
↕
↕
↕
↕
8
↕
↕
↕
↕
↕
2
2
4
4
6
LDC @aa:24, CCR
W @aa:24 →CCR
STC CCR, Rd
B
STC CCR, @ERd
W CCR →@ERd
STC CCR, @(d:16,
ERd)
W CCR →@(d:16, ERd)
6
STC CCR, @(d:24,
ERd)
W CCR →@(d:24, ERd)
10
STC CCR, @–ERd
W ERd32–2 →ERd32
CCR →@ERd
STC CCR, @aa:16
W CCR →@aa:16
STC CCR, @aa:24
W CCR →@aa:24
ANDC #xx:8, CCR
B
CCR∧#xx:8 →CCR
ORC #xx:8, CCR
B
XORC #xx:8, CCR
B
NOP
— PC ←PC+2
↕
10
— — — — — —
2
— — — — — —
6
— — — — — —
8
— — — — — —
12
— — — — — —
8
6
— — — — — —
8
8
8
CCR →Rd8
2
4
4
— — — — — —
10
2
↕
↕
↕
↕
↕
↕
2
CCR∨#xx:8 →CCR
2
↕
↕
↕
↕
↕
↕
2
CCR⊕#xx:8 →CCR
2
↕
↕
↕
↕
↕
↕
2
2 — — — — — —
2
398
Table A-1 Instruction Set (cont)
Block transfer instructions
Condition Code
I
H N
Z
V
C
Advanced
No. of
States *1
Implied
@@aa
@(d, PC)
@aa
@–ERn/@ERn+
@(d, ERn)
@ERn
Rn
Operation
#xx
Mnemonic
Operand Size
Addressing Mode and
Instruction Length (bytes)
Normal
8.
EEPMOV. B
— if R4L ≠ 0 then
repeat @R5 →@R6
R5+1 →R5
R6+1 →R6
R4L–1 →R4L
until
R4L=0
else next
4 — — — — — —
8+4n*2
EEPMOV. W
— if R4 ≠ 0 then
repeat @R5 →@R6
R5+1 →R5
R6+1 →R6
R4L–1 →R4
until
R4=0
else next
4 — — — — — —
8+4n*2
Notes: 1. The number of states is the number of states required for execution when the instruction and its
operands are located in on-chip memory. For other cases see section A.3, Number of States
Required for Execution.
2. n is the value set in register R4L or R4.
(1) Set to 1 when a carry or borrow occurs at bit 11; otherwise cleared to 0.
(2) Set to 1 when a carry or borrow occurs at bit 27; otherwise cleared to 0.
(3) Retains its previous value when the result is zero; otherwise cleared to 0.
(4) Set to 1 when the adjustment produces a carry; otherwise retains its previous value.
(5) The number of states required for execution of an instruction that transfers data in
synchronization with the E clock is variable.
(6) Set to 1 when the divisor is negative; otherwise cleared to 0.
(7) Set to 1 when the divisor is zero; otherwise cleared to 0.
(8) Set to 1 when the quotient is negative; otherwise cleared to 0.
399
400
AH
2
STC
1
Table A.2
(2)
LDC
3
BVC
OR
XOR
AND
MOV
C
D
E
F
BILD
BIST
BLD
BST
MOV
BVS
9
A
B
JMP
BPL
BMI
MOV
Table A.2 Table A.2
(2)
(2)
Table A.2 Table A.2
(2)
(2)
Table A.2 Table A.2
EEPMOV
(2)
(2)
SUB
ADD
MOV.B
8
Table A.2
TRAPA
(2)
BEQ
SUBX
BIAND
BAND
AND
RTE
BNE
B
BIXOR
BXOR
XOR
BSR
BCS
CMP
BIOR
BOR
OR
RTS
BCC
Table A.2
(2)
LDC
7
A
BTST
DIVXU
BLS
AND.B
ANDC
6
ADDX
BCLR
MULXU
BHI
XOR.B
XORC
5
9
BNOT
DIVXU
BRN
OR.B
ORG
4
BSR
BGE
C
CMP
MOV
Instruction when most significant bit of BH is 1.
Instruction when most significant bit of BH is 0.
ADD
BSET
MULXU
BRA
Table A.2 Table A.2 Table A.2 Table A.2
(2)
(2)
(2)
(2)
NOP
0
1st byte 2nd byte
AH AL BH BL
8
7
6
5
4
3
2
1
0
AL
Instruction code:
Table A-2 Operation Code Map (1)
A.2 Operation Code Maps
E
JSR
BGT
SUBX
ADDX
Table A.2
(3)
BLT
D
F
BLE
Table A.2
(2)
Table A.2
(2)
401
SUBS
DAS
BRA
MOV
MOV
1B
1F
58
79
7A
CMP
CMP
ADD
ADD
2
BHI
1
SUB
SUB
BLS
OR
OR
XOR
XOR
BCS
AND
AND
BEQ
BVC
SUB
9
BVS
NEG
NOT
DEC
ROTR
ROTXR
DEC
ROTL
ADDS
SLEEP
8
ROTXL
EXTU
INC
7
SHAR
BNE
6
SHLR
EXTU
INC
5
SHAL
BCC
LDC/STC
4
SHLL
3
1st byte 2nd byte
AH AL BH BL
BRN
NOT
17
DEC
ROTXR
13
1A
ROTXL
12
DAA
0F
SHLR
ADDS
0B
11
INC
0A
SHLL
MOV
01
10
0
BH
AH AL
Instruction code:
Table A-2 Operation Code Map (2)
BPL
A
MOV
BMI
NEG
CMP
SUB
ROTR
ROTL
SHAR
C
D
BGE
BLT
DEC
EXTS
INC
Table A.2 Table A.2
(3)
(3)
ADD
SHAL
B
BGT
E
BLE
DEC
EXTS
INC
Table A.2
(3)
F
402
C
BSET
7Faa7 * 2
BNOT
BNOT
BCLR
BCLR
Notes: 1. r is the register designation field.
2. aa is the absolute address field.
BSET
7Faa6 * 2
BTST
BCLR
BTST
BTST
DIVXS
3
7Eaa7 * 2
BNOT
BCLR
MULXS
2
BTST
BSET
7Dr07 * 1
BNOT
DIVXS
1
BIOR
BOR
BIOR
BOR
OR
4
BIXOR
BXOR
BIXOR
BXOR
XOR
5
BIAND
BAND
BIAND
BAND
AND
6
7
BIST
BILD
BST
BLD
BIST
BILD
BST
BID
1st byte 2nd byte 3rd byte 4th byte
AH AL BH BL CH CL DH DL
7Eaa6 * 2
BSET
MULXS
0
7Dr06 * 1
7Cr07 * 1
7Cr06 * 1
01F06
01D05
01C05
01406
AH
ALBH
BLCH
Instruction code:
Table A-2 Operation Code Map (3)
8
LDC
STC
9
A
LDC
STC
B
C
LDC
STC
D
E
LDC
STC
F
Instruction when most significant bit of DH is 1.
Instruction when most significant bit of DH is 0.
A.3 Number of States Required for Execution
The tables in this section can be used to calculate the number of states required for instruction
execution by the H8/300H CPU. Table A-3 indicates the number of instruction fetch, data
read/write, and other cycles occurring in each instruction. Table A-3 indicates the number of states
required per cycle according to the bus size. The number of states required for execution of an
instruction can be calculated from these two tables as follows:
Number of states = I ×SI + J ×SJ + K ×SK + L ×SL + M ×SM + N ×SN
Examples of Calculation of Number of States Required for Execution
Examples: Advanced mode, stack located in external address space, on-chip supporting modules
accessed with 8-bit bus width, external devices accessed in three states with one wait state and
16-bit bus width.
BSET #0, @FFFFFC7:8
From table A-4, I = L = 2 and J = K = M = N = 0
From table A-3, SI = 4 and SL = 3
Number of states = 2 ×4 + 2 ×3 = 14
JSR @@30
From table A-3, I = J = K = 2 and L = M = N = 0
From table A-3, SI = SJ = SK = 4
Number of states = 2 ×4 + 2 ×4 + 2 ×4 = 24
403
Table A-3 Number of States per Cycle
Access Conditions
External Device
On-Chip Supporting Module
Cycle
8-Bit Bus
16-Bit Bus
On-Chip
Memory
8-Bit
Bus
16-Bit
Bus
2-State 3-State 2-State 3-State
Access Access Access Access
2
6
3
4
6 + 2m
Instruction fetch
SI
Branch address read
SJ
Stack operation
SK
Byte data access
SL
3
2
3+m
Word data access
SM
6
4
6 + 2m
Internal operation
SN 1
Legend
m: Number of wait states inserted into external device access
404
2
3+m
Table A-4 Number of Cycles per Instruction
Instruction Mnemonic
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
ADD
ADD.B #xx:8, Rd
ADD.B Rs, Rd
ADD.W #xx:16, Rd
ADD.W Rs, Rd
ADD.L #xx:32, ERd
ADD.L ERs, ERd
1
1
2
1
3
1
ADDS
ADDS #1/2/4, ERd
1
ADDX
ADDX #xx:8, Rd
ADDX Rs, Rd
1
1
AND
AND.B #xx:8, Rd
AND.B Rs, Rd
AND.W #xx:16, Rd
AND.W Rs, Rd
AND.L #xx:32, ERd
AND.L ERs, ERd
1
1
2
1
3
2
ANDC
ANDC #xx:8, CCR
1
BAND
BAND #xx:3, Rd
BAND #xx:3, @ERd
BAND #xx:3, @aa:8
1
2
2
BRA d:8 (BT d:8)
BRN d:8 (BF d:8)
BHI d:8
BLS d:8
BCC d:8 (BHS d:8)
BCS d:8 (BLO d:8)
BNE d:8
BEQ d:8
BVC d:8
BVS d:8
BPL d:8
BMI d:8
BGE d:8
BLT d:8
BGT d:8
BLE d:8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Bcc
1
1
405
Table A-4 Number of Cycles per Instruction (cont)
Instruction Mnemonic
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Bcc
BRA d:16 (BT d:16)
BRN d:16 (BF d:16)
BHI d:16
BLS d:16
BCC d:16 (BHS d:16)
BCS d:16 (BLO d:16)
BNE d:16
BEQ d:16
BVC d:16
BVS d:16
BPL d:16
BMI d:16
BGE d:16
BLT d:16
BGT d:16
BLE d:16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
BCLR
BCLR #xx:3, Rd
BCLR #xx:3, @ERd
BCLR #xx:3, @aa:8
BCLR Rn, Rd
BCLR Rn, @ERd
BCLR Rn, @aa:8
1
2
2
1
2
2
BIAND #xx:3, Rd
BIAND #xx:3, @ERd
BIAND #xx:3, @aa:8
1
2
2
1
1
BILD #xx:3, Rd
BILD #xx:3, @ERd
BILD #xx:3, @aa:8
1
2
2
1
1
BIOR #xx:8, Rd
BIOR #xx:8, @ERd
BIOR #xx:8, @aa:8
1
2
2
1
1
BIST #xx:3, Rd
BIST #xx:3, @ERd
BIST #xx:3, @aa:8
1
2
2
2
2
BIXOR #xx:3, Rd
BIXOR #xx:3, @ERd
BIXOR #xx:3, @aa:8
1
2
2
1
1
BLD #xx:3, Rd
BLD #xx:3, @ERd
BLD #xx:3, @aa:8
1
2
2
1
1
BIAND
BILD
BIOR
BIST
BIXOR
BLD
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
406
Table A-4 Number of Cycles per Instruction (cont)
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
BNOT
BOR
BSET
BSR
BNOT #xx:3, Rd
BNOT #xx:3, @ERd
BNOT #xx:3, @aa:8
BNOT Rn, Rd
BNOT Rn, @ERd
BNOT Rn, @aa:8
1
2
2
1
2
2
BOR #xx:3, Rd
BOR #xx:3, @ERd
BOR #xx:3, @aa:8
1
2
2
BSET #xx:3, Rd
BSET #xx:3, @ERd
BSET #xx:3, @aa:8
BSET Rn, Rd
BSET Rn, @ERd
BSET Rn, @aa:8
1
2
2
1
2
2
BSR d:8
2
2
2
2
2
1
2
2
2
1
2
2
2
2
BST #xx:3, Rd
BST #xx:3, @ERd
BST #xx:3, @aa:8
1
2
2
BTST #xx:3, Rd
BTST #xx:3, @ERd
BTST #xx:3, @aa:8
BTST Rn, Rd
BTST Rn, @ERd
BTST Rn, @aa:8
1
2
2
1
2
2
BXOR #xx:3, Rd
BXOR #xx:3, @ERd
BXOR #xx:3, @aa:8
1
2
2
CMP
CMP.B #xx:8, Rd
CMP.B Rs, Rd
CMP.W #xx:16, Rd
CMP.W Rs, Rd
CMP.L #xx:32, ERd
CMP.L ERs, ERd
1
1
2
1
3
1
DAA
DAA Rd
1
DAS
DAS Rd
1
BXOR
1
1
Normal
Advanced
BTST
2
2
Advanced
BSR d:16 Normal
BST
2
2
2
2
1
1
1
1
1
1
407
Table A-4 Number of Cycles per Instruction (cont)
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
DEC
DEC.B Rd
DEC.W #1/2, Rd
DEC.L #1/2, ERd
1
1
1
DIVXS
DIVXS.B Rs, Rd
DIVXS.W Rs, ERd
2
2
12
20
DIVXU
DIVXU.B Rs, Rd
DIVXU.W Rs, ERd
1
1
12
20
EEPMOV
EEPMOV.B
EEPMOV.W
2
2
EXTS
EXTS.W Rd
EXTS.L ERd
1
1
EXTU
EXTU.W Rd
EXTU.L ERd
1
1
INC
INC.B Rd
INC.W #1/2, Rd
INC.L #1/2, ERd
1
1
1
JMP
JMP @ERn
2
JMP @aa:24
2
JMP @@aa:8 Normal
2
1
Advanced 2
2
JSR
JSR @ERn
Normal
2n + 2*1
2n + 2*1
2
2
2
2
1
Advanced 2
2
JSR @aa:24 Normal
2
Advanced 2
JSR @@aa:8 Normal
LDC
1
2
2
2
2
1
1
Advanced 2
2
2
LDC #xx:8, CCR
LDC Rs, CCR
LDC @ERs, CCR
LDC @(d:16, ERs), CCR
LDC @(d:24, ERs), CCR
LDC @ERs+, CCR
LDC @aa:16, CCR
LDC @aa:24, CCR
1
1
2
3
5
2
3
4
1
1
1
1
1
1
408
2
Table A-4 Number of Cycles per Instruction (cont)
Instruction Mnemonic
MOV
MOV.B #xx:8, Rd
MOV.B Rs, Rd
MOV.B @ERs, Rd
MOV.B @(d:16, ERs), Rd
MOV.B @(d:24, ERs), Rd
MOV.B @ERs+, Rd
MOV.B @aa:8, Rd
MOV.B @aa:16, Rd
MOV.B @aa:24, Rd
MOV.B Rs, @ERd
MOV.B Rs, @(d:16, ERd)
MOV.B Rs, @(d:24, ERd)
MOV.B Rs, @–ERd
MOV.B Rs, @aa:8
MOV.B Rs, @aa:16
MOV.B Rs, @aa:24
MOV.W #xx:16, Rd
MOV.W Rs, Rd
MOV.W @ERs, Rd
MOV.W @(d:16, ERs), Rd
MOV.W @(d:24, ERs), Rd
MOV.W @ERs+, Rd
MOV.W @aa:16, Rd
MOV.W @aa:24, Rd
MOV.W Rs, @ERd
MOV.W Rs, @(d:16, ERd)
MOV.W Rs, @(d:24, ERd)
MOV.W Rs, @–ERd
MOV.W Rs, @aa:16
MOV.W Rs, @aa:24
MOV.L #xx:32, ERd
MOV.L ERs, ERd
MOV.L @ERs, ERd
MOV.L @(d:16, ERs), ERd
MOV.L @(d:24, ERs), ERd
MOV.L @ERs+, ERd
MOV.L @aa:16, ERd
MOV.L @aa:24, ERd
MOV.L ERs, @ERd
MOV.L ERs, @(d:16, ERd)
MOV.L ERs, @(d:24, ERd)
MOV.L ERs, @–ERd
MOV.L ERs, @aa:16
MOV.L ERs, @aa:24
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
1
1
1
2
4
1
1
2
3
1
2
4
1
1
2
3
2
1
1
2
4
1
2
3
1
2
4
1
2
3
3
1
2
3
5
2
3
4
2
3
5
2
3
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
409
2
2
2
2
Table A-4 Number of Cycles per Instruction (cont)
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
MOVFPE
MOVFPE @aa:16, Rd*2 2
@aa:16*2
1
MOVTPE
MOVTPE Rs,
MULXS
MULXS.B Rs, Rd
MULXS.W Rs, ERd
2
2
2
1
12
20
MULXU
MULXU.B Rs, Rd
MULXU.W Rs, ERd
1
1
12
20
NEG
NEG.B Rd
NEG.W Rd
NEG.L ERd
1
1
1
NOP
NOP
1
NOT
NOT.B Rd
NOT.W Rd
NOT.L ERd
1
1
1
OR
OR.B #xx:8, Rd
OR.B Rs, Rd
OR.W #xx:16, Rd
OR.W Rs, Rd
OR.L #xx:32, ERd
OR.L ERs, ERd
1
1
2
1
3
2
ORC
ORC #xx:8, CCR
1
POP
POP.W Rn
POP.L ERn
1
2
1
2
2
2
PUSH
PUSH.W Rn
PUSH.L ERn
1
2
1
2
2
2
ROTL
ROTL.B Rd
ROTL.W Rd
ROTL.L ERd
1
1
1
ROTR
ROTR.B Rd
ROTR.W Rd
ROTR.L ERd
1
1
1
ROTXL
ROTXL.B Rd
ROTXL.W Rd
ROTXL.L ERd
1
1
1
ROTXR
ROTXR.B Rd
ROTXR.W Rd
ROTXR.L ERd
1
1
1
RTE
RTE
2
2
410
2
Table A-4 Number of Cycles per Instruction (cont)
Instruction Branch
Stack
Byte Data Word Data Internal
Fetch
Addr. Read Operation Access
Access
Operation
I
J
K
L
M
N
Instruction Mnemonic
RTS
RTS
Normal
2
1
2
SHAL
SHAL.B Rd
SHAL.W Rd
SHAL.L ERd
Advanced 2
1
1
1
2
2
SHAR
SHAR.B Rd
SHAR.W Rd
SHAR.L ERd
1
1
1
SHLL
SHLL.B Rd
SHLL.W Rd
SHLL.L ERd
1
1
1
SHLR
SHLR.B Rd
SHLR.W Rd
SHLR.L ERd
1
1
1
SLEEP
SLEEP
1
STC
STC CCR, Rd
1
STC CCR, @ERd
2
STC CCR, @(d:16, ERd) 3
STC CCR, @(d:24, ERd) 5
STC CCR, @–ERd
2
STC CCR, @aa:16
3
STC CCR, @aa:24
4
1
1
1
1
1
1
2
SUB
SUB.B Rs, Rd
SUB.W #xx:16, Rd
SUB.W Rs, Rd
SUB.L #xx:32, ERd
SUB.L ERs, ERd
1
2
1
3
1
SUBS
SUBS #1/2/4, ERd
1
SUBX
SUBX #xx:8, Rd
SUBX Rs, Rd
1
1
TRAPA
TRAPA #x:2 Normal
2
1
2
4
Advanced 2
2
2
4
XOR
XOR.B #xx:8, Rd
XOR.B Rs, Rd
XOR.W #xx:16, Rd
XOR.W Rs, Rd
XOR.L #xx:32, ERd
XOR.L ERs, ERd
1
1
2
1
3
2
XORC
XORC #xx:8, CCR
1
Notes: 1. n is the value set in register R4L or R4. The source and destination are accessed n + 1 times each.
2. Not available in the H8/3004 and H8/3005.
411
Appendix B Register Field
B.1 Register Addresses and Bit Names
Address Register
(low)
Name
Data
Bus
Width
Bit Names
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module Name
H'1C
H'1D
H'1E
H'1F
H'20
—
—
—
—
—
—
—
—
—
H'21
—
—
—
—
—
—
—
—
—
H'22
—
—
—
—
—
—
—
—
—
H'23
—
—
—
—
—
—
—
—
—
H'24
—
—
—
—
—
—
—
—
—
H'25
—
—
—
—
—
—
—
—
—
H'26
—
—
—
—
—
—
—
—
—
H'27
—
—
—
—
—
—
—
—
—
H'28
—
—
—
—
—
—
—
—
—
H'29
—
—
—
—
—
—
—
—
—
H'2A
—
—
—
—
—
—
—
—
—
H'2B
—
—
—
—
—
—
—
—
—
H'2C
—
—
—
—
—
—
—
—
—
H'2D
—
—
—
—
—
—
—
—
—
H'2E
—
—
—
—
—
—
—
—
—
H'2F
—
—
—
—
—
—
—
—
—
H'30
—
—
—
—
—
—
—
—
—
H'31
—
—
—
—
—
—
—
—
—
H'32
—
—
—
—
—
—
—
—
—
H'33
—
—
—
—
—
—
—
—
—
H'34
—
—
—
—
—
—
—
—
—
H'35
—
—
—
—
—
—
—
—
—
H'36
—
—
—
—
—
—
—
—
—
H'37
—
—
—
—
—
—
—
—
—
H'38
—
—
—
—
—
—
—
—
—
H'39
—
—
—
—
—
—
—
—
—
H'3A
—
—
—
—
—
—
—
—
—
Legend
DMAC: DMA controller
(Continued on next page)
412
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit Names
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'3B
—
—
—
—
—
—
—
—
—
H'3C
—
—
—
—
—
—
—
—
—
H'3D
—
—
—
—
—
—
—
—
—
H'3E
—
—
—
—
—
—
—
—
—
H'3F
—
—
—
—
—
—
—
—
—
H'40
—
—
—
—
—
—
—
—
—
H'41
—
—
—
—
—
—
—
—
—
H'42
—
—
—
—
—
—
—
—
—
H'43
—
—
—
—
—
—
—
—
—
H'44
—
—
—
—
—
—
—
—
—
H'45
—
—
—
—
—
—
—
—
—
H'46
—
—
—
—
—
—
—
—
—
H'47
—
—
—
—
—
—
—
—
—
H'48
—
—
—
—
—
—
—
—
—
H'49
—
—
—
—
—
—
—
—
—
H'4A
—
—
—
—
—
—
—
—
—
H'4B
—
—
—
—
—
—
—
—
—
H'4C
—
—
—
—
—
—
—
—
—
H'4D
—
—
—
—
—
—
—
—
—
H'4E
—
—
—
—
—
—
—
—
—
H'4F
—
—
—
—
—
—
—
—
—
H'50
—
—
—
—
—
—
—
—
—
H'51
—
—
—
—
—
—
—
—
—
H'52
—
—
—
—
—
—
—
—
—
H'53
—
—
—
—
—
—
—
—
—
H'54
—
—
—
—
—
—
—
—
—
H'55
—
—
—
—
—
—
—
—
—
H'56
—
—
—
—
—
—
—
—
—
H'57
—
—
—
—
—
—
—
—
—
H'58
—
—
—
—
—
—
—
—
—
H'59
—
—
—
—
—
—
—
—
—
H'5A
—
—
—
—
—
—
—
—
—
H'5B
—
—
—
—
—
—
—
—
—
H'5C
—
—
—
—
—
—
—
—
—
H'5D
—
—
—
—
—
—
—
—
—
H'5E
—
—
—
—
—
—
—
—
—
H'5F
—
—
—
—
—
—
—
—
—
Module Name
(Continued on next page)
413
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Module Name
H'60
TSTR
8
—
—
—
STR4
STR3
STR2
STR1
STR0
H'61
TSNC
8
—
—
—
SYNC4 SYNC3 SYNC2 SYNC1 SYNC0
ITU
(all channels)
H'62
TMDR
8
—
MDF
FDIR
PWM4
PWM3
PWM2
PWM1
PWM0
H'63
TFCR
8
—
—
CMD1
CMD0
BFB4
BFA4
BFB3
BFA3
H'64
TCR0
8
—
CCLR1
CCLR0
CKEG1 CKEG0 TPSC2
TPSC1
TPSC0
H'65
TIOR0
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'66
TIER0
8
—
—
—
—
—
OVIE
IMIEB
IMIEA
H'67
TSR0
8
—
—
—
—
—
OVF
IMFB
IMFA
H'68
TCNT0H
16
Bit Names
H'69
TCNT0L
H'6A
GRA0H
H'6B
GRA0L
H'6C
GRB0H
H'6D
GRB0L
H'6E
TCR1
8
—
CCLR1
CCLR0
CKEG1 CKEG0 TPSC2
TPSC1
TPSC0
H'6F
TIOR1
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'70
TIER1
8
—
—
—
—
—
OVIE
IMIEB
IMIEA
H'71
TSR1
8
—
—
—
—
—
OVF
IMFB
IMFA
H'72
TCNT1H
16
H'73
TCNT1L
H'74
GRA1H
H'75
GRA1L
H'76
GRB1H
H'77
GRB1L
H'78
TCR2
8
—
CCLR1
CCLR0
CKEG1 CKEG0 TPSC2
TPSC1
TPSC0
H'79
TIOR2
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'7A
TIER2
8
—
—
—
—
—
OVIE
IMIEB
IMIEA
H'7B
TSR2
8
—
—
—
—
—
OVF
IMFB
IMFA
H'7C
TCNT2H
16
H'7D
TCNT2L
H'7E
GRA2H
H'7F
GRA2L
H'80
GRB2H
H'81
GRB2L
ITU channel 0
16
16
ITU channel 1
16
16
ITU channel 2
16
16
Legend
ITU: 16-bit integrated timer unit
(Continued on next page)
414
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit 7
Bit 6
Bit 5
Bit 4
Bit 1
Bit 0
Module Name
H'82
TCR3
8
—
CCLR1
CCLR0
CKEG1 CKEG0 TPSC2
TPSC1
TPSC0
ITU channel 3
H'83
TIOR3
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'84
TIER3
8
—
—
—
—
—
OVIE
IMIEB
IMIEA
H'85
TSR3
8
—
—
—
—
—
OVF
IMFB
IMFA
H'86
TCNT3H
16
H'87
TCNT3L
H'88
GRA3H
H'89
GRA3L
H'8A
GRB3H
H'8B
GRB3L
H'8C
BRA3H
H'8D
BRA3L
H'8E
BRB3H
H'8F
BRB3L
H'90
TOER
8
—
—
EXB4
EXA4
EB3
EB4
EA4
EA3
H'91
TOCR
8
—
—
—
XTGD
—
—
OLS4
OLS3
ITU
(all channels)
H'92
TCR4
8
—
CCLR1
CCLR0
CKEG1 CKEG0 TPSC2
TPSC1
TPSC0
ITU channel 4
H'93
TIOR4
8
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
H'94
TIER4
8
—
—
—
—
—
OVIE
IMIEB
IMIEA
H'95
TSR4
8
—
—
—
—
—
OVF
IMFB
IMFA
H'96
TCNT4H
16
H'97
TCNT4L
H'98
GRA4H
H'99
GRA4L
H'9A
GRB4H
H'9B
GRB4L
H'9C
BRA4H
H'9D
BRA4L
H'9E
BRB4H
H'9F
BRB4L
Bit Names
Bit 3
Bit 2
16
16
16
16
16
16
16
16
Legend
ITU: 16-bit integrated timer unit
(Continued on next page)
415
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit Names
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'A0
—
—
—
—
—
—
—
—
—
H'A1
—
—
—
—
—
—
—
—
—
H'A2
—
—
—
—
—
—
—
—
—
H'A3
—
—
—
—
—
—
—
—
—
H'A4
—
—
—
—
—
—
—
—
—
H'A5
—
—
—
—
—
—
—
—
—
H'A6
—
—
—
—
—
—
—
—
—
H'A7
—
—
—
—
—
—
—
—
—
H'A8
TCSR*1
8
OVF
WT/IT
TME
—
—
CKS2
CKS1
CKS0
H'A9
TCNT*1
8
H'AA
—
—
—
—
—
—
—
—
—
H'AB
RSTCSR*2 8
WRST
RSTOE —
—
—
—
—
—
H'AC
—
—
—
—
—
—
—
—
—
H'AD
—
—
—
—
—
—
—
—
—
H'AE
—
—
—
—
—
—
—
—
—
H'AF
—
—
—
—
—
—
—
—
—
H'B0
SMR
8
C/A
CHR
PE
O/E
STOP
MP
CKS1
CKS0
H'B1
BRR
8
H'B2
SCR
8
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
H'B3
TDR
8
H'B4
SSR
8
TDRE
RDRF
ORER
FER
PER
TEND
MPB
MPBT
H'B5
RDR
8
H'B6
—
—
—
—
—
—
—
—
—
H'B7
—
—
—
—
—
—
—
—
—
Module Name
WDT
SCI channel 0
Notes: 1. For write access to TCSR and TCNT, see section 10.2.4, Notes on Register Access.
2. For write access to RSTCSR, see section 10.2.4, Notes on Register Access.
Legend
WDT: Watchdog timer
(Continued on next page)
416
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit Names
Bit 3
Bit 2
Bit 1
Bit 0
H'B8
—
—
—
—
—
—
—
—
—
H'B9
—
—
—
—
—
—
—
—
—
H'BA
—
—
—
—
—
—
—
—
—
H'BB
—
—
—
—
—
—
—
—
—
H'BC
—
—
—
—
—
—
—
—
—
H'BD
—
—
—
—
—
—
—
—
—
H'BE
—
—
—
—
—
—
—
—
—
H'BF
—
—
—
—
—
—
—
—
—
H'C0
—
—
—
—
—
—
—
—
—
H'C1
—
—
—
—
—
—
—
—
—
H'C2
—
—
—
—
—
—
—
—
—
H'C3
—
—
—
—
—
—
—
—
—
H'C4
—
—
—
—
—
—
—
—
—
H'C5
—
—
—
—
—
—
—
—
—
H'C6
—
—
—
—
—
—
—
—
—
H'C7
—
—
—
—
—
—
—
—
—
H'C8
—
—
—
—
—
—
—
—
—
H'C9
P6DDR
—
—
—
—
—
—
—
P60DDR
H'CA
—
—
—
—
—
—
—
—
—
8
8
Bit 7
Bit 6
Bit 5
Bit 4
Module Name
Port 6
H'CB
P6DR
H'CC
—
—
—
—
—
—
—
—
P60
—
—
—
—
—
—
—
—
H'CD
P8DDR
8
—
—
—
H'CE
P7DR
8
P77
P76
P83DDR P82DDR P81DDR P80DDR
Port 8
P75
P74
P73
P72
P71
P70
H'CF
P8DR
8
—
Port 7
—
—
—
P83
P82
P81
P80
Port 8
H'D0
P9DDR
8
—
H'D1
PADDR
8
PA7DDR PA6DDR PA5DDR PA4DDR PA3DDR PA2DDR PA1DDR PA0DDR
—
—
P94DDR —
P90DDR
Port 9
H'D2
P9DR
8
—
—
—
P94
—
P92
—
P90
Port 9
H'D3
PADR
8
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
Port A
H'D4
PBDDR
8
PB7DDR PB6DDR PB5DDR PB4DDR PB3DDR PB2DDR PB1DDR PB0DDR
H'D5
—
8
—
—
—
—
—
—
—
—
P92DDR —
H'D6
PBDR
8
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
H'D7
—
8
—
—
—
—
—
—
—
—
Port A
Port B
Port B
(Continued on next page)
417
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit Names
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
H'D8
—
—
—
—
—
—
—
—
—
H'D9
—
—
—
—
—
—
—
—
—
H'DA
—
—
—
—
—
—
—
—
—
H'DB
—
—
—
—
—
—
—
—
—
H'DC
—
—
—
—
—
—
—
—
—
H'DD
—
—
—
—
—
—
—
—
—
H'DE
—
—
—
—
—
—
—
—
—
H'DF
—
—
—
—
—
—
—
—
—
H'E0
ADDRAH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'E1
ADDRAL
8
AD1
AD0
—
—
—
—
—
—
H'E2
ADDRBH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'E3
ADDRBL
8
AD1
AD0
—
—
—
—
—
—
H'E4
ADDRCH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'E5
ADDRCL
8
AD1
AD0
—
—
—
—
—
—
H'E6
ADDRDH
8
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
H'E7
ADDRDL
8
AD1
AD0
—
—
—
—
—
—
H'E8
ADCSR
8
ADF
ADIE
ADST
SCAN
CKS
CH2
CH1
CH0
H'E9
ADCR
8
TRGE
—
—
—
—
—
—
—
H'EA
—
—
—
—
—
—
—
—
—
H'EB
—
—
—
—
—
—
—
—
—
H'EC
—
—
—
—
—
—
—
—
—
H'ED
ASTCR
8
AST7
AST6
AST5
AST4
AST3
AST2
AST1
AST0
H'EE
WCR
8
—
—
—
—
WMS1
WMS0
WC1
WC0
H'EF
WCER
8
WCE7
WCE6
WCE5
WCE4
WCE3
WCE2
WCE1
WCE0
Module Name
A/D
Bus controller
Legend
A/D: A/D converter
(Continued on next page)
418
(Continued from preceding page)
Address Register
(low)
Name
Data
Bus
Width
Bit Names
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
—
—
—
—
—
—
—
—
H'F0
—
H'F1
MDCR
8
—
—
—
—
—
—
MDS1
MDS0
H'F2
SYSCR
8
SSBY
STS2
STS1
STS0
UE
NMIEG
—
RAME
H'F3
—
—
—
—
—
—
—
—
—
H'F4
ISCR
8
—
—
—
IRQ4SC IRQ3SC IRQ2SC IRQ1SC IRQ0SC
H'F5
IER
8
—
—
—
IRQ4E
IRQ3E
IRQ2E
IRQ1E
IRQ0E
H'F6
ISR
8
—
—
—
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
H'F7
—
—
—
—
—
—
—
—
—
H'F8
IPRA
8
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
H'F9
IPRB
8
IPRB7
IPRB6
—
—
IPRB3
—
IPRB1
—
H'FA
—
—
—
—
—
—
—
—
—
H'FB
—
—
—
—
—
—
—
—
—
H'FC
—
—
—
—
—
—
—
—
—
H'FD
—
—
—
—
—
—
—
—
—
H'FE
—
—
—
—
—
—
—
—
—
H'FF
—
—
—
—
—
—
—
—
—
419
Module Name
System control
IInterrupt
controller
Interrupt
controller
B.2 Register Descriptions
Register
acronym
Register
name
TSTR Timer Start Register
Address to which
the register is mapped
H'60
Name of on-chip
supporting
module
ITU (all channels)
Bit
numbers
Bit
Initial bit
values
7
6
5
4
3
2
1
0
—
—
—
STR4
STR3
STR2
STR1
STR0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Names of the
bits. Dashes
(—) indicate
reserved bits.
Possible types of access
R
Read only
W
Write only
Counter start 0
0 TCNT0 is halted
1 TCNT0 is counting
R/W Read and write
Counter start 1
0 TCNT1 is halted
1 TCNT1 is counting
Full name
of bit
Counter start 2
0 TCNT2 is halted
1 TCNT2 is counting
Counter start 3
0 TCNT3 is halted
1 TCNT3 is counting
Counter start 4
0 TCNT4 is halted
1 TCNT4 is counting
420
Descriptions
of bit settings
TSTR—Timer Start Register
Bit
H'60
ITU (all channels)
7
6
5
4
3
2
1
0
—
—
—
STR4
STR3
STR2
STR1
STR0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Counter start 0
0 TCNT0 is halted
1 TCNT0 is counting
Counter start 1
0 TCNT1 is halted
1 TCNT1 is counting
Counter start 2
0 TCNT2 is halted
1 TCNT2 is counting
Counter start 3
0 TCNT3 is halted
1 TCNT3 is counting
Counter start 4
0 TCNT4 is halted
1 TCNT4 is counting
421
TSNC—Timer Synchro Register
Bit
H'61
ITU (all channels)
7
6
5
4
3
2
1
0
—
—
—
SYNC4
SYNC3
SYNC2
SYNC1
SYNC0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Timer sync 0
0 TCNT0 operates independently
1 TCNT0 is synchronized
Timer sync 1
0 TCNT1 operates independently
1 TCNT1 is synchronized
Timer sync 2
0 TCNT2 operates independently
1 TCNT2 is synchronized
Timer sync 3
0 TCNT3 operates independently
1 TCNT3 is synchronized
Timer sync 4
0 TCNT4 operates independently
1 TCNT4 is synchronized
422
TMDR—Timer Mode Register
Bit
H'62
ITU (all channels)
7
6
5
4
3
2
1
0
—
MDF
FDIR
PWM4
PWM3
PWM2
PWM1
PWM0
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
PWM mode 0
0 Channel 0 operates normally
1 Channel 0 operates in PWM mode
PWM mode 1
0 Channel 1 operates normally
1 Channel 1 operates in PWM mode
PWM mode 2
0 Channel 2 operates normally
1 Channel 2 operates in PWM mode
PWM mode 3
0 Channel 3 operates normally
1 Channel 3 operates in PWM mode
PWM mode 4
0 Channel 4 operates normally
1 Channel 4 operates in PWM mode
Flag direction
0 OVF is set to 1 in TSR2 when TCNT2 overflows or underflows
1 OVF is set to 1 in TSR2 when TCNT2 overflows
Phase counting mode flag
0 Channel 2 operates normally
1 Channel 2 operates in phase counting mode
423
TFCR—Timer Function Control Register
Bit
H'63
ITU (all channels)
7
6
5
4
3
2
1
0
—
—
CMD1
CMD0
BFB4
BFA4
BFB3
BFA3
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
R/W
R/W
R/W
R/W
R/W
R/W
Buffer mode A3
0 GRA3 operates normally
1 GRA3 is buffered by BRA3
Buffer mode B3
0 GRB3 operates normally
1 GRB3 is buffered by BRB3
Buffer mode A4
0 GRA4 operates normally
1 GRA4 is buffered by BRA4
Buffer mode B4
0 GRB4 operates normally
1 GRB4 is buffered by BRB4
Combination mode 1 and 0
Bit 5 Bit 4
CMD1 CMD0 Operating Mode of Channels 3 and 4
0
0
Channels 3 and 4 operate normally
1
0
1
Channels 3 and 4 operate together in complementary PWM mode
1
Channels 3 and 4 operate together in reset-synchronized PWM mode
424
TCR0—Timer Control Register 0
Bit
H'64
7
6
5
—
CCLR1
CCLR0
Initial value
1
0
0
0
Read/Write
—
R/W
R/W
R/W
4
3
ITU0
2
1
0
TPSC2
TPSC1
TPSC0
0
0
0
0
R/W
R/W
R/W
R/W
CKEG1 CKEG0
Timer prescaler 2 to 0
Bit 2
Bit 0
Bit 1
TPSC2 TPSC1 TPSC0
0
0
0
1
0
1
1
0
0
1
1
0
1
1
TCNT Clock Source
Internal clock: ø
Internal clock: ø/2
Internal clock: ø/4
Internal clock: ø/8
External clock A: TCLKA input
External clock B: TCLKB input
External clock C: TCLKC input
External clock D: TCLKD input
Clock edge 1 and 0
Bit 4 Bit 3
CKEG1 CKEG0
0
0
1
1
—
Counted Edges of External Clock
Rising edges counted
Falling edges counted
Both edges counted
Counter clear 1 and 0
Bit 6
Bit 5
CCLR1 CCLR0 TCNT Clear Source
0
0
TCNT is not cleared
1
TCNT is cleared by GRA compare match or input capture
1
0
TCNT is cleared by GRB compare match or input capture
1
Synchronous clear: TCNT is cleared in synchronization
with other synchronized timers
425
TIOR0—Timer I/O Control Register 0
Bit
H'65
ITU0
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
I/O control A2 to A0
Bit 2 Bit 1 Bit 0
IOA2 IOA1 IOA0
0
0
0
1
0
1
1
0
0
1
1
0
1
1
I/O control B2 to B0
Bit 6 Bit 5 Bit 4
IOB2 IOB1 IOB0
0
0
0
1
0
1
1
0
0
1
1
0
1
1
GRA Function
GRA is an output
compare register
GRA is an input
capture register
GRB Function
GRB is an output
compare register
GRB is an input
capture register
No output at compare match
0 output at GRA compare match
1 output at GRA compare match
Output toggles at GRA compare match
GRA captures rising edge of input
GRA captures falling edge of input
GRA captures both edges of input
No output at compare match
0 output at GRB compare match
1 output at GRB compare match
Output toggles at GRB compare match
GRB captures rising edge of input
GRB captures falling edge of input
GRB captures both edges of input
426
TIER0—Timer Interrupt Enable Register 0
Bit
H'66
ITU0
7
6
5
4
3
2
1
0
—
—
—
—
—
OVIE
IMIEB
IMIEA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Input capture/compare match interrupt enable A
0 IMIA interrupt requested by IMFA is disabled
1 IMIA interrupt requested by IMFA is enabled
Input capture/compare match interrupt enable B
0 IMIB interrupt requested by IMFB is disabled
1 IMIB interrupt requested by IMFB is enabled
Overflow interrupt enable
0 OVI interrupt requested by OVF is disabled
1 OVI interrupt requested by OVF is enabled
427
TSR0—Timer Status Register 0
Bit
H'67
ITU0
7
6
5
4
3
2
1
0
—
—
—
—
—
OVF
IMFB
IMFA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/(W)*
R/(W)*
R/(W)*
Input capture/compare match flag A
0 [Clearing condition]
Read IMFA when IMFA = 1, then write 0 in IMFA
1 [Setting conditions]
TCNT = GRA when GRA functions as a compare
match register.
TCNT value is transferred to GRA by an input capture
signal, when GRA functions as an input capture register.
Input capture/compare match flag B
0 [Clearing condition]
Read IMFB when IMFB = 1, then write 0 in IMFB
1 [Setting conditions]
TCNT = GRB when GRB functions as a compare
match register.
TCNT value is transferred to GRB by an input capture
signal, when GRB functions as an input capture register.
Overflow flag
0 [Clearing condition]
Read OVF when OVF = 1, then write 0 in OVF
1 [Setting condition]
TCNT overflowed from H'FFFF to H'0000
Note: * Only 0 can be written, to clear the flag.
428
TCNT0 H/L—Timer Counter 0 H/L
H'68, H'69
ITU0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Up-counter
GRA0 H/L—General Register A0 H/L
Bit
Initial value
Read/Write
H'6A, H'6B
ITU0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Output compare or input capture register
GRB0 H/L—General Register B0 H/L
H'6C, H'6D
ITU0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Output compare or input capture register
TCR1—Timer Control Register 1
Bit
H'6E
7
6
5
—
CCLR1
CCLR0
4
3
CKEG1 CKEG0
ITU1
2
1
0
TPSC2
TPSC1
TPSC0
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
429
TIOR1—Timer I/O Control Register 1
Bit
H'6F
ITU1
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TIER1—Timer Interrupt Enable Register 1
Bit
H'70
ITU1
7
6
5
4
3
2
1
0
—
—
—
—
—
OVIE
IMIEB
IMIEA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TSR1—Timer Status Register 1
Bit
H'71
ITU1
7
6
5
4
3
2
1
0
—
—
—
—
—
OVF
IMFB
IMFA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/(W)*
R/(W)*
R/(W)*
Notes: Bit functions are the same as for ITU0.
* Only 0 can be written, to clear the flag.
TCNT1 H/L—Timer Counter 1 H/L
H'72, H'73
ITU1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
430
GRA1 H/L—General Register A1 H/L
H'74, H'75
ITU1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
GRB1 H/L—General Register B1 H/L
H'76, H'77
ITU1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
TCR2—Timer Control Register 2
Bit
H'78
7
6
5
—
CCLR1
CCLR0
Initial value
1
0
0
0
Read/Write
—
R/W
R/W
R/W
4
3
ITU2
2
1
0
TPSC2
TPSC1
TPSC0
0
0
0
0
R/W
R/W
R/W
R/W
CKEG1 CKEG0
Notes: 1. Bit functions are the same as for ITU0.
2. When channel 2 is used in phase counting mode, the counter clock source selection by
bits TPSC2 to TPSC0 is ignored.
431
TIOR2—Timer I/O Control Register 2
Bit
H'79
ITU2
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
432
TIER2—Timer Interrupt Enable Register 2
Bit
H'7A
ITU2
7
6
5
4
3
2
1
0
—
—
—
—
—
OVIE
IMIEB
IMIEA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TSR2—Timer Status Register 2
Bit
H'7B
ITU2
7
6
5
4
3
2
1
0
—
—
—
—
—
OVF
IMFB
IMFA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/(W)*
R/(W)*
R/(W)*
Bit functions are the
same as for ITU0.
Overflow flag
0 [Clearing condition]
Read OVF when OVF = 1, then write 0 in OVF
1 [Setting condition]
TCNT overflowed from H'FFFF to H'0000 or underflowed from
H'0000 to H'FFFF
Note: * Only 0 can be written, to clear the flag.
TCNT2 H/L—Timer Counter 2 H/L
H'7C, H'7D
ITU2
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Phase counting mode: up/down counter
Other modes:
up-counter
433
GRA2 H/L—General Register A2 H/L
H'7E, H'7F
ITU2
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
GRB2 H/L—General Register B2 H/L
H'80, H'81
ITU2
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
TCR3—Timer Control Register 3
Bit
H'82
ITU3
7
6
5
4
3
2
1
0
—
CCLR1
CCLR0
CKEG1
CLEG0
TPSC2
TPSC1
TPSC0
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TIOR3—Timer I/O Control Register 3
Bit
H'83
ITU3
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
434
TIER3—Timer Interrupt Enable Register 3
Bit
H'84
ITU3
7
6
5
4
3
2
1
0
—
—
—
—
—
OVIE
IMIEB
IMIEA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TSR3—Timer Status Register 3
Bit
H'85
ITU3
7
6
5
4
3
2
1
0
—
—
—
—
—
OVF
IMFB
IMFA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/(W)*
R/(W)*
R/(W)*
Bit functions are the
same as for ITU0
Overflow flag
0 [Clearing condition]
Read OVF when OVF = 1, then write 0 in OVF
1 [Setting condition]
TCNT overflowed from H'FFFF to H'0000 or underflowed from
H'0000 to H'FFFF
Note: * Only 0 can be written, to clear the flag.
TCNT3 H/L—Timer Counter 3 H/L
Bit
Initial value
Read/Write
H'86, H'87
ITU3
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Complementary PWM mode: up/down counter
Other modes:
up-counter
435
GRA3 H/L—General Register A3 H/L
H'88, H'89
ITU3
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Output compare or input capture register (can be buffered)
GRB3 H/L—General Register B3 H/L
Bit
Initial value
Read/Write
H'8A, H'8B
ITU3
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Output compare or input capture register (can be buffered)
BRA3 H/L—Buffer Register A3 H/L
H'8C, H'8D
ITU3
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Used to buffer GRA
BRB3 H/L—Buffer Register B3 H/L
H'8E, H'8F
ITU3
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Used to buffer GRB
436
TOER—Timer Output Enable Register
Bit
H'90
ITU (all channels)
7
6
5
4
3
2
1
0
—
—
EXB4
EXA4
EB3
EB4
EA4
EA3
Initial value
1
1
1
1
1
1
1
1
Read/Write
—
—
R/W
R/W
R/W
R/W
R/W
R/W
Master enable TIOCA3
0 TIOCA 3 output is disabled regardless of TIOR3, TMDR, and TFCR settings
1 TIOCA 3 is enabled for output according to TIOR3, TMDR, and TFCR settings
Master enable TIOCA4
0 TIOCA 4 output is disabled regardless of TIOR4, TMDR, and TFCR settings
1 TIOCA 4 is enabled for output according to TIOR4, TMDR, and TFCR settings
Master enable TIOCB4
0 TIOCB4 output is disabled regardless of TIOR4 and TFCR settings
1 TIOCB4 is enabled for output according to TIOR4 and TFCR settings
Master enable TIOCB3
0 TIOCB 3 output is disabled regardless of TIOR3 and TFCR settings
1 TIOCB 3 is enabled for output according to TIOR3 and TFCR settings
Master enable TOCXA4
0 TOCXA 4 output is disabled regardless of TFCR settings
1 TOCXA 4 is enabled for output according to TFCR settings
Master enable TOCXB4
0 TOCXB4 output is disabled regardless of TFCR settings
1 TOCXB4 is enabled for output according to TFCR settings
437
TOCR—Timer Output Control Register
Bit
H'91
ITU (all channels)
7
6
5
4
3
2
1
0
—
—
—
XTGD
—
—
OLS4
OLS3
Initial value
1
1
1
1
1
1
1
1
Read/Write
—
—
—
R/W
—
—
R/W
R/W
Output level select 3
0 TIOCB 3 , TOCXA 4 , and TOCXB 4 outputs are inverted
1 TIOCB 3 , TOCXA 4 , and TOCXB 4 outputs are not inverted
Output level select 4
0 TIOCA 3 , TIOCA 4, and TIOCB4 outputs are inverted
1 TIOCA 3 , TIOCA 4, and TIOCB4 outputs are not inverted
External trigger disable
0 Input capture A in channel 1 is used as an external trigger signal in
reset-synchronized PWM mode and complementary PWM mode *
1 External triggering is disabled
Note: * When an external trigger occurs, bits 5 to 0 in TOER are cleared to 0, disabling ITU
output.
438
TCR4—Timer Control Register 4
Bit
H'92
7
6
5
—
CCLR1
CCLR0
Initial value
1
0
0
0
Read/Write
—
R/W
R/W
R/W
4
3
ITU4
2
1
0
TPSC2
TPSC1
TPSC0
0
0
0
0
R/W
R/W
R/W
R/W
CKEG1 CKEG0
Note: Bit functions are the same as for ITU0.
TIOR4—Timer I/O Control Register 4
Bit
H'93
ITU4
7
6
5
4
3
2
1
0
—
IOB2
IOB1
IOB0
—
IOA2
IOA1
IOA0
Initial value
1
0
0
0
1
0
0
0
Read/Write
—
R/W
R/W
R/W
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TIER4—Timer Interrupt Enable Register 4
Bit
H'94
ITU4
7
6
5
4
3
2
1
0
—
—
—
—
—
OVIE
IMIEB
IMIEA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/W
R/W
R/W
Note: Bit functions are the same as for ITU0.
TSR4—Timer Status Register 4
Bit
H'95
ITU4
7
6
5
4
3
2
1
0
—
—
—
—
—
OVF
IMFB
IMFA
Initial value
1
1
1
1
1
0
0
0
Read/Write
—
—
—
—
—
R/(W)*
R/(W)*
R/(W)*
Notes: Bit functions are the same as for ITU0.
* Only 0 can be written, to clear the flag.
439
TCNT4 H/L—Timer Counter 4 H/L
H'96, H'97
ITU4
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
GRA4 H/L—General Register A4 H/L
Bit
Initial value
Read/Write
H'98, H'99
ITU4
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
GRB4 H/L—General Register B4 H/L
H'9A, H'9B
ITU4
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
BRA4 H/L—Buffer Register A4 H/L
H'9C, H'9D
ITU4
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
440
BRB4 H/L—Buffer Register B4 H/L
H'9E, H'9F
ITU4
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Read/Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
TCSR—Timer Control/Status Register
Bit
H'A8
WDT
7
6
5
4
3
2
1
0
OVF
WT/ IT
TME
—
—
CKS2
CKS1
CKS0
Initial value
0
0
0
1
1
0
0
0
Read/Write
R/(W)*
R/W
R/W
—
—
R/W
R/W
R/W
Timer enable
0 Timer disabled
• TCNT is initialized to H'00 and halted
1 Timer enabled
• TCNT is counting
• CPU interrupt requests are enabled
Timer mode select
0 Interval timer: requests interval timer interrupts
1 Watchdog timer: generates a reset signal
Overflow flag
0 [Clearing condition]
Read OVF when OVF = 1, then write 0 in OVF
1 [Setting condition]
TCNT changes from H'FF to H'00
Note: * Only 0 can be written, to clear the flag.
441
Clock select 2 to 0
0
0
0
1
0
1
1
0
0
1
1
0
1
1
ø/2
ø/32
ø/64
ø/128
ø/256
ø/512
ø/2048
ø/4096
TCNT—Timer Counter
H'A9 (read),
H'A8 (write)
WDT
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Count value
RSTCSR—Reset Control/Status Register
Bit
H'AB (read),
H'AA (write)
WDT
7
6
5
4
3
2
1
0
WRST
RSTOE
—
—
—
—
—
—
Initial value
0
0
1
1
1
1
1
1
Read/Write
R/(W)*
R/W
—
—
—
—
—
—
Reset output enable
0 Reset signal is not output externally
1 Reset signal is output externally
Watchdog timer reset
0 [Clearing condition]
Reset signal input at RES pin, or 0 written by software
1 [Setting condition]
TCNT overflow generates a reset signal
Note: * Only 0 can be written in bit 7, to clear the flag.
442
SMR—Serial Mode Register
H'B0
SCI
7
6
5
7
3
2
1
0
C/ A
CHR
PE
O/ E
STOP
MP
CKS1
CKS0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Multiprocessor mode
0 Multiprocessor function disabled
1 Multiprocessor format selected
Stop bit length
0 One stop bit
1 Two stop bits
Parity mode
0 Even parity
1 Odd parity
Parity enable
0 Parity bit is not added or checked
1 Parity bit is added and checked
Character length
0 8-bit data
1 7-bit data
Communication mode
0 Asynchronous mode
1 Synchronous mode
443
Clock select 1 and 0
Bit 1 Bit 0
CKS1 CKS0 Clock Source
0
0
ø clock
1
ø/4 clock
0
1
ø/16 clock
1
ø/64 clock
BRR—Bit Rate Register
H'B1
SCI
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Serial communication bit rate setting
444
SCR—Serial Control Register
Bit
H'B2
SCI
7
6
5
4
3
2
1
0
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Clock enable 1 and 0
Bit 1 Bit 2
CKE1 CKE2 Clock Selection and Output
0
0
Asynchronous mode Internal clock, SCK pin available for generic input
Synchronous mode Internal clock, SCK pin used for serial clock output
1
Asynchronous mode Internal clock, SCK pin used for clock output
Synchronous mode Internal clock, SCK pin used for serial clock output
Asynchronous mode External clock, SCK pin used for clock input
1
0
Synchronous mode External clock, SCK pin used for serial clock input
Asynchronous mode External clock, SCK pin used for clock input
1
Synchronous mode External clock, SCK pin used for serial clock input
Transmit-end interrupt enable
0 Transmit-end interrupt requests (TEI) are disabled
1 Transmit-end interrupt requests (TEI) are enabled
Multiprocessor interrupt enable
0 Multiprocessor interrupts are disabled (normal receive operation)
1 Multiprocessor interrupts are enabled
Transmit enable
0 Transmitting is disabled
1 Transmitting is enabled
Receive enable
0 Transmitting is disabled
1 Transmitting is enabled
Receive interrupt enable
0 Receive-data-full (RXI) and receive-error (ERI) interrupt requests are disabled
1 Receive-data-full (RXI) and receive-error (ERI) interrupt requests are enabled
Transmit interrupt enable
0 Transmit-data-empty interrupt request (TXI) is disabled
1 Transmit-data-empty interrupt request (TXI) is enabled
445
TDR—Transmit Data Register
H'B3
SCI
Bit
7
6
5
4
3
2
1
0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Serial transmit data
446
SSR—Serial Status Register
Bit
H'B4
SCI
7
6
5
4
3
2
1
0
TDRE
RDRF
ORER
FER
PER
TEND
MPB
MPBT
Initial value
1
0
0
0
0
1
0
0
Read/Write
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R
R
R/W
Multiprocessor bit
0 Multiprocessor bit value in
receive data is 0
1
Transmit end
Multiprocessor bit value in
receive data is 1
Multiprocessor bit transfer
0 Multiprocessor bit value in
transmit data is 0
1
0
[Clearing conditions]
Read TDRE when TDRE = 1, then write 0 in TDRE.
1
[Setting conditions]
Reset or transition to standby mode.
TE is cleared to 0 in SCR.
TDRE is 1 when last bit of serial character is transmitted.
Multiprocessor bit value in
transmit data is 1
Parity error
Framing error
0
[Clearing conditions]
Reset or transition to standby mode.
Read FER when FER = 1, then write 0
in FER.
1
[Setting condition]
Framing error (stop bit is 0)
0
[Clearing conditions]
Reset or transition to standby mode.
Read PER when PER = 1, then write 0 in
PER.
1
[Setting condition]
Parity error: (parity of receive data does not
match parity setting of O/ E in SMR)
Overrun error
Receive data register full
0
[Clearing conditions]
Reset or transition to standby mode.
Read RDRF when RDRF = 1, then write 0 in
RDRF.
1
[Setting condition]
Serial data is received normally and transferred
from RSR to RDR
Transmit data register empty
0
[Clearing conditions]
Read TDRE when TDRE = 1, then write 0 in TDRE.
1
[Setting conditions]
Reset or transition to standby mode.
TE is 0 in SCR
Data is transferred from TDR to TSR, enabling new
data to be written in TDR.
Note: * Only 0 can be written, to clear the flag.
447
0
[Clearing conditions]
Reset or transition to standby mode.
Read ORER when ORER = 1, then write 0 in
ORER.
1
[Setting condition]
Overrun error (reception of next serial data
ends when RDRF = 1)
RDR—Receive Data Register
H'B5
SCI
Bit
7
6
5
4
3
2
1
0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
Serial receive data
P6DDR—Port 6 Data Direction Register
Bit
H'C9
Port 6
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
P60DDR
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
W
W
W
W
W
W
W
Port 6 input/output select
0 Generic input
1 Generic output
P6DR—Port 6 Data Register
Bit
H'CB
Port 6
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
P60
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Data for port 6 pins
448
P8DDR—Port 8 Data Direction Register
Bit
H'CD
2
Port 8
7
6
5
4
—
—
—
—
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
W
W
W
W
W
3
1
0
P8 3 DDR P8 2 DDR P8 1 DDR P8 0 DDR
Port 8 input/output select
0 Generic input
1 Generic output
P7DR—Port 7 Data Register
Bit
H'CE
Port 7
7
6
5
4
3
2
1
0
P77
P76
P75
P74
P73
P72
P71
P70
Initial value
—*
—*
—*
—*
—*
—*
—*
—*
Read/Write
R
R
R
R
R
R
R
R
Data for port 7 pins
Note: * Determined by pins P7 7 to P7 0 .
P8DR—Port 8 Data Register
Bit
H'CF
Port 8
7
6
5
4
3
2
1
0
—
—
—
—
P8 3
P8 2
P8 1
P8 0
Initial value
1
1
1
0
0
0
0
0
Read/Write
—
—
—
R/W
R/W
R/W
R/W
R/W
Data for port 8 pins
449
P9DDR—Port 9 Data Direction Register
Bit
H'D0
Port 9
7
6
5
4
3
2
1
0
—
—
—
P9 4 DDR
—
P9 2 DDR
—
P9 0 DDR
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
W
W
W
W
W
W
Port 9 input/output select
0 Generic input
1 Generic output
PADDR—Port A Data Direction Register
7
Bit
6
5
H'D1
4
3
2
Port A
1
0
PA7 DDR PA6 DDR PA5 DDR PA4 DDR PA3 DDR PA2 DDR PA1 DDR PA0 DDR
Mode 1
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Initial value
1
0
0
0
0
0
0
0
Read/Write
—
W
W
W
W
W
W
W
Mode 3
Port A input/output select
0 Generic input
1 Generic output
P9DR—Port 9 Data Register
Bit
H'D2
Port 9
7
6
5
4
3
2
1
0
—
—
—
P9 4
—
P9 2
—
P9 0
Initial value
1
1
0
0
0
0
0
0
Read/Write
—
—
R/W
R/W
R/W
R/W
R/W
R/W
Data for port 9 pins
450
Bit
7
6
5
4
3
2
1
0
PA 7
PA 6
PA 5
PA 4
PA 3
PA 2
PA 1
PA 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
2
1
0
Data for port A pins
Bit
7
6
5
4
3
PB7 DDR PB6 DDR PB5 DDR PB4 DDR PB3 DDR PB2 DDR PB1 DDR PB0 DDR
Initial value
0
0
0
0
0
0
0
0
Read/Write
W
W
W
W
W
W
W
W
Port B input/output select
0 Generic input
1 Generic output
Bit
7
6
5
4
3
2
1
0
PB 7
PB 6
PB 5
PB 4
PB 3
PB 2
PB 1
PB 0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Data for port B pins
451
PADR—Port A Data Register
Bit
14
H'D3
12
10
8
6
Port A
5
4
3
2
1
0
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 —
—
—
—
—
—
15
13
11
9
7
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
ADDRAH
ADDRAL
A/D conversion data
10-bit data giving an
A/D conversion result
PBDDR—Port B Data Direction Register
Bit
14
12
10
H'D4
8
6
Port B
5
4
3
2
1
0
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 —
—
—
—
—
—
15
13
11
9
7
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
ADDRBH
ADDRBL
A/D conversion data
10-bit data giving an
A/D conversion result
PBDR—Port B Data Register
Bit
14
H'D6
12
10
8
6
Port B
5
4
3
2
1
0
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 —
15
13
11
9
7
—
—
—
—
—
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
ADDRCH
ADDRCL
A/D conversion data
10-bit data giving an
A/D conversion result
452
ADDRA H/L—A/D Data Register A H/L
Bit
14
12
H'E0, H'E1
10
8
6
A/D
5
4
3
2
1
0
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 —
—
—
—
—
—
15
13
11
9
7
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
ADDRDH
ADDRDL
A/D conversion data
10-bit data giving an
A/D conversion result
ADDRB H/L—A/D Data Register B H/L
Bit
H'E2, H'E3
A/D
7
6
5
4
3
2
1
0
TRGE
—
—
—
—
—
—
—
Initial value
0
1
1
1
1
1
1
1
Read/Write
R/W
—
—
—
—
—
—
—
Trigger enable
0 A/D conversion cannot be externally triggered
1 A/D conversion starts at the fall of the external trigger signal (ADTRG )
ADDRC H/L—A/D Data Register C H/L
H'E4, H'E5
453
A/D
ADDRD H/L—A/D Data Register D H/L
Bit
H'E6, H'E7
A/D
7
6
5
4
3
2
1
0
ADF
ADIE
ADST
SCAN
CKS
CH2
CH1
CH0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Clock select
0 Conversion time = 266 states (maximum)
1 Conversion time = 134 states (maximum)
Scan mode
0 Single mode
1 Scan mode
Channel select 2 to 0
Channel
Group
Selection
Selection
CH2
CH1
CH0
0
0
0
1
0
1
1
0
0
1
1
0
1
1
Description
Single Mode Scan Mode
AN 0
AN 0
AN 1
AN 0, AN 1
AN 2
AN 0 to AN 2
AN 3
AN 0 to AN 3
AN 4
AN 4
AN 5
AN 4, AN 5
AN 6
AN 4 to AN 6
AN 7
AN 4 to AN 7
A/D start
0 A/D conversion is stopped
1 Single mode: A/D conversion starts; ADST is automatically cleared to 0 when
conversion ends
Scan mode: A/D conversion starts and continues, cycling among the selected
channels, until ADST is cleared to 0 by software, by a reset, or by a
transition to standby mode
A/D interrupt enable
0 A/D end interrupt request is disabled
1 A/D end interrupt request is enabled
A/D end flag
0 [Clearing condition]
Read ADF while ADF = 1, then write 0 in ADF
1 [Setting conditions]
Single mode: A/D conversion ends
Scan mode: A/D conversion ends in all selected channels
Note: * Only 0 can be written, to clear flag.
454
Bit
7
6
5
4
3
2
1
0
AST7
AST6
AST5
AST4
AST3
AST2
AST1
AST0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Area 7 to 0 access state control
Bits 7 to 0
AST7 to AST0
Number of States in Access Cycle
0
Areas 7 to 0 are two-state access areas
Areas 7 to 0 are three-state access areas
1
ADCR—A/D Control Register
Bit
H'E9
A/D
7
6
5
4
3
2
1
0
—
—
—
—
WMS1
WMS0
WC1
WC0
Initial value
1
1
1
1
0
0
1
1
Read/Write
—
—
—
—
R/W
R/W
R/W
R/W
Wait mode select 1 and 0
Bit 3 Bit 2
WMS1 WMS0 Wait Mode
0
0
Programmable wait mode
1
No wait states inserted by
wait-state controller
1
0
1
Wait count 1 and 0
Bit 1 Bit 0
WC1 WC0 Number of Wait States
0
0
No wait states inserted by
wait-state controller
Pin wait mode
Pin auto-wait mode
1
455
1
0
1
1 state inserted
2 states inserted
3 states inserted
ADCSR—A/D Control/Status Register
Bit
H'E8
A/D
7
6
5
4
3
2
1
0
WCE7
WCE6
WCE5
WCE4
WCE3
WCE2
WCE1
WCE0
Initial value
1
1
1
1
1
1
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Wait state controller enable 7 to 0
0 Wait-state control is disabled (pin wait mode 0)
1 Wait-state control is enabled
ASTCR—Access State Control Register
Bit
H'ED
Bus controller
7
6
5
4
3
2
1
0
—
—
—
—
—
—
MDS1
MDS0
Initial value
1
1
0
0
0
0
—*
—*
Read/Write
—
—
—
—
—
—
R
R
Mode select 1 and 0
Bit 1 Bit 0
MD1 MD0 Operating mode
0
—
0
Mode 1
1
—
0
1
Mode 3
1
Note: * Determined by the state of the mode pins (MD 1 and MD0 ).
WCR—Wait Control Register
H'EE
456
Bus controller
WCER—Wait Controller Enable Register
Bit
H'EF
Bus controller
7
6
5
4
3
2
1
0
SSBY
STS2
STS1
STS0
UE
NMIEG
—
RAME
Initial value
0
0
0
0
1
0
1
1
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
—
R/W
RAM enable
0 On-chip RAM is disabled
1 On-chip RAM is enabled
NMI edge select
0 An interrupt is requested at the falling edge of NMI
1 An interrupt is requested at the rising edge of NMI
User bit enable
0 CCR bit 6 (UI) is used as an interrupt mask bit
1 CCR bit 6 (UI) is used as a user bit
Standby timer select 2 to 0
Bit 6 Bit 5 Bit 4
STS2 STS1 STS0 Standby Timer
0
0
0
Waiting time = 8192 states
1
Waiting time = 16384 states
0
Waiting time = 32768 states
1
1
Waiting time = 65536 states
Waiting time = 131072 states
0
—
1
—
Illegal setting
1
Software standby
0 SLEEP instruction causes transition to sleep mode
1 SLEEP instruction causes transition to software standby mode
MDCR—Mode Control Register
H'F1
457
System control
SYSCR—System Control Register
Bit
H'F2
7
6
5
4
3
2
System control
1
0
—
—
—
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
IRQ4SC IRQ3SC IRQ2SC IRQ1SC IRQ0SC
IRQ 4 to IRQ 0 sense control
0 Interrupts are requested when IRQ 4 to IRQ 0 inputs are low
1 Interrupts are requested by falling-edge input at IRQ 4 to IRQ0
Bit
7
6
5
4
3
2
1
0
—
—
—
IRQ4E
IRQ3E
IRQ2E
IRQ1E
IRQ0E
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/(W)
R/(W)
R/(W)
R/(W)
R/(W)
R/(W)
R/(W)
R/(W)
IRQ4 to IRQ 0 enable
0 IRQ 4 to IRQ 0 interrupts are disabled
1 IRQ 4 to IRQ 0 interrupts are enabled
458
ISCR—IRQ Sense Control Register
Bit
H'F4
Interrupt controller
7
6
5
4
3
2
1
0
—
—
—
IRQ4F
IRQ3F
IRQ2F
IRQ1F
IRQ0F
Initial value
0
0
0
0
0
0
0
0
Read/Write
—
—
—
R/(W)*
R/(W)*
R/(W)*
R/(W)*
R/(W)*
IRQ 4 to IRQ 0 flags
Bits 4 to 0
IRQ4F to IRQ0F
0
1
Setting and Clearing Conditions
[Clearing conditions]
Read IRQnF when IRQnF = 1, then write 0 in IRQnF.
IRQnSC = 0, IRQn input is high, and interrupt exception
handling is carried out.
IRQnSC = 1 and IRQn interrupt exception handling is
carried out.
[Setting conditions]
IRQnSC = 0 and IRQn input is low.
IRQnSC = 1 and IRQn input changes from high to low.
(n = 4 to 0)
Note: * Only 0 can be written, to clear the flag.
IER—IRQ Enable Register
H'F5
459
Interrupt controller
ISR—IRQ Status Register
Bit
H'F6
Interrupt controller
7
6
5
4
3
2
1
0
IPRA7
IPRA6
IPRA5
IPRA4
IPRA3
IPRA2
IPRA1
IPRA0
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Priority level A7 to A0
0 Priority level 0 (low priority)
1 Priority level 1 (high priority)
Bit
7
6
5
4
3
2
1
0
IPRB7
IPRB6
—
—
IPRB3
—
IPRB1
—
Initial value
0
0
0
0
0
0
0
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Priority level B7, B6, B3, and B1
0 Priority level 0 (low priority)
1 Priority level 1 (high priority)
460
Appendix C I/O Port Block Diagrams
Reset
R
Q
D
P60DDR
C
Mode 2/3
WP6D
Reset
R
P60
Q
P60DR
Internal data bus
C.1 Port 6 Block Diagram
Bus controller
WAIT
input
enable
D
C
WP6
RP6
Bus controller
WAIT
input
WP6D: Write to P6DDR
WP6: Write to port 6
RP6: Read port 6
Figure C-1 Port 6 Block Diagram (Pin P60)
461
RP7
P7n
Internal data bus
C.2 Port 7 Block Diagram
A/D converter
Input enable
Analog input
RP7: Read port 7
n = 0 to 7
Figure C-2 Port 7 Block Diagram
462
C.3 Port 8 Block Diagram
R
Q
D
P80DDR
C
WP8D
Reset
Internal data bus
Reset
R
P80
Q
P80DR
D
C
WP8
RP8
Interrupt
controller
IRQ0
input
WP8D: Write to P8DDR
WP8: Write to port 8
RP8: Read port 8
Figure C-3 (a) Port 8 Block Diagram (Pin P80)
463
R
Q
D
P8nDDR
C
WP8
Internal data bus
Reset
Reset
Mode 2, 3
R
Q
P8n
Mode 1
P8nDR
D
C
WP8
RP8
Interrupt controller
IRQ1
IRQ2
IRQ3 input
WP8D: Write to P8DDR
WP8: Write to port 8
RP8: Read port 8
n = 1 to 3
Figure C-3 (b) Port 8 Block Diagram (Pin P81, P82, P83)
464
C.4 Port 9 Block Diagram
R
Q
D
P90DDR
C
WP9D
Internal data bus
Reset
Reset
R
Q
P90
P90DR
D
SCI
C
WP9
Output enable
Serial data
RP9
WP9D: Write to P9DDR
WP9: Write to port 9
RP9: Read port 9
Figure C-4 (a) Port 9 Block Diagram (Pin P90)
465
R
Q
D
P92DDR
C
WP9D
Reset
Internal data bus
Reset
SCI
Input
enable
R
Q
P92
P92DR
D
C
WP9
RP9
Serial
data
WP9D: Write to P9DDR
WP9: Write to port 9
RP9: Read port 9
Figure C-4 (b) Port 9 Block Diagram (Pins P92)
466
R
Q
D
P94DDR
C
WP9D
Reset
Internal data bus
Reset
SCI
Clock input
enable
R
Q
P94
P94DR
D
C
WP9
Clock output
enable
Clock output
RP9
Clock input
WP9D: Write to P9DDR
WP9: Write to port 9
RP9: Read port 9
n = 4, 5
Interrupt controller
IRQ4 input
Figure C-4 (c) Port 9 Block Diagram (Pin P94)
467
Internal data bus
C.5 Port A Block Diagram
Reset
R
Q
D
PAnDDR
C
WPAD
Reset
TPC output
enable
R
PAn
Q
PAnDR
TPC
D
Next data
C
WPA
Output trigger
ITU
RPA
Counter
input
clock
WPAD: Write to PADDR
WPA: Write to port A
RPA: Read port A
n = 0, 1
Figure C-5 (a) Port A Block Diagram (Pins PA0, PA1)
468
Internal data bus
Reset
R
Q
D
PAnDDR
C
TPC
WPAD
Reset
TPC output
enable
R
Q
PAn
PAnDR
D
Next data
C
WPA
Output trigger
ITU
Output enable
Compare
match output
RPA
WPAD: Write to PADDR
WPA: Write to port A
RPA: Read port A
n = 2, 3
Figure C-5 (b) Port A Block Diagram (Pins PA2, PA3)
469
Input capture
input
Counter input
clock
Software standby
Internal data bus
Reset
R
Q
D
PAnDDR
C
WPAD
Internal address bus
Mode 3
TPC
Reset
TPC output
enable
R
PAn
Q
PAnDR
D
Next data
C
WPA
Output trigger
ITU
Output enable
Compare
match output
RPA
Input capture
input
WPAD: Write to PADDR
WPA: Write to port A
RPA: Read port A
n = 4 to 7
Figure C-5 (c) Port A Block Diagram (Pins PA4 to PA7)
470
Internal data bus
C.6 Port B Block Diagram
Reset
R
Q
D
PBnDDR
C
TPC
WPBD
Reset
TPC output
enable
R
Q
PBn
PBnDR
D
Next data
C
WPB
Output trigger
ITU
Output enable
Compare
match output
RPB
Input capture
input
WPBD: Write to PBDDR
WPB: Write to port B
RPB: Read port B
n = 0 to 3
Figure C-6 (a) Port B Block Diagram (Pins PB0 to PB3)
471
Internal data bus
Reset
R
Q
D
PBnDDR
C
TPC
WPBD
Reset
TPC output
enable
R
Q
PBn
PBnDR
D
Next data
C
WPB
Output trigger
ITU
Output enable
Compare
match output
RPB
WPBD: Write to PBDDR
WPB: Write to port B
RPB: Read port B
n = 4 to 5
Figure C-6 (b) Port B Block Diagram (Pins PB4, PB5)
472
Internal data bus
Reset
R
Q
D
PB6DDR
C
TPC
WPBD
Reset
TPC output
enable
R
PB6
Q
PB6DR
D
Next data
C
WPB
Output trigger
RPB
WPBD: Write to PBDDR
WPB: Write to port B
RPB: Read port B
Figure C-6 (c) Port B Block Diagram (Pin PB6)
473
Internal data bus
Reset
R
Q
D
PB7DDR
C
TPC
WPBD
Reset
TPC output
enable
R
PB7
Q
PB7DR
D
Next data
C
WPB
Output trigger
RPB
A/D converter
ADTRG
input
WPBD: Write to PBDDR
WPB: Write to port B
RPB: Read port B
Figure C-6 (d) Port B Block Diagram (Pin PB7)
474
Appendix D Pin States
D.1 Port States in Each Mode
Table D-1 Port States
Software
Standby
Mode
Sleep
Mode
Clock output T
H
Clock output Clock output
—
T*1
T
T
T
RESO
1, 3 WAIT pin
—
—
T
T
WAIT
T
T
T
T
I/O port
Pin
Name
Mode
Reset
State
ø
—
RESO
P60
Generic
I/O pin
Hardware
Standby
Mode
Program
Execution
Sleep Mode
P77 to P70
1, 3
T
T
T
T
Input port
P83 to P80
1, 3
T
T
keep
keep
I/O port
P94, P92,
P90
1, 3
T
T
keep
keep
I/O port
PA3 to PA0
1, 3
T
T
keep
keep
I/O port
PA7 to PA4
1
T
T
keep
keep
I/O port
3
T
T
I/O port*2
A20 to A23
A20 to A23
1, 3
T
T
keep
keep
I/O port
PB7 to PB0
Legend
H:
High
L:
Low
T:
High-impedance state
keep: Input pins are in the high-impedance state; output pins maintain their previous state.
DDR: Data direction register bit
Notes: 1. A low level is output only in the case of a reset due to WDT overflow.
2. The pin states at this time depend on the DDR setting.
475
D.2 Pin States at Reset
Reset in T1 State: Figure D-1 is a timing diagram for the case in which RES goes low during the
T1 state of an external memory access cycle. As soon as RES goes low, all ports are initialized to
the input state. AS, RD, and WR go high, and the data bus goes to the high-impedance state. The
address bus is initialized to the low output level 0.5 state after the low level of RES is sampled.
Sampling of RES takes place at the fall of the system clock (ø).
Access to external address
T2
T1
T3
ø
RES
Internal
reset signal
Address bus
(mode 1)
H'000000
AS (mode 1)
High
RD (read access)
(mode 1)
High
WR (write access)
(mode 1)
High
Data bus
(write access)
(mode 1)
High impedance
I/O port
(modes 1, 3)
High impedance
Figure D-1 Reset during Memory Access (Reset during T1 State)
476
Reset in T2 State: Figure D-2 is a timing diagram for the case in which RES goes low during the
T2 state of an external memory access cycle. As soon as RES goes low, all ports are initialized to
the input state. AS, RD, and WR go high, and the data bus goes to the high-impedance state. The
address bus is initialized to the low output level 0.5 state after the low level of RES is sampled.
The same timing applies when a reset occurs during a wait state (TW).
Access to external address
T2
T1
T3
ø
RES
Internal
reset signal
Address bus
(mode 1)
H'000000
AS (mode 1)
RD (read access)
(mode 1)
WR (write access)
(mode 1)
Data bus
(write access)
(mode 1)
High impedance
High impedance
I/O port
(modes 1, 3)
Figure D-2 Reset during Memory Access (Reset during T2 State)
477
Reset in T3 State: Figure D-3 is a timing diagram for the case in which RES goes low during the
T3 state of an external memory access cycle. As soon as RES goes low, all ports are initialized to
the input state. AS, RD, and WR go high, and the data bus goes to the high-impedance state. The
address bus outputs are held during the T3 state.The same timing applies when a reset occurs in
the T2 state of an access cycle to a two-state-access area.
Access to external address
T2
T1
T3
ø
RES
Internal
reset signal
Address bus
(mode 1)
H'000000
AS (mode 1)
RD (read access)
(mode 1)
WR (write access)
(mode 1)
Data bus
(write access)
(mode 1)
High impedance
I/O port
(modes 1, 3)
High impedance
Figure D-3 Reset during Memory Access (Reset during T3 State)
478
Appendix E Timing of Transition to and Recovery from
Hardware Standby Mode
Timing of Transition to Hardware Standby Mode
(1) To retain RAM contents with the RAME bit set to 1 in SYSCR, drive the RES signal low 10
system clock cycles before the STBY signal goes low, as shown below. RES must remain low
until STBY goes low (minimum delay from STBY low to RES high: 0 ns).
STBY
t1 ≥ 10tcyc
t2 ≥ 0 ns
RES
(2) To retain RAM contents with the RAME bit cleared to 0 in SYSCR, RES does not have to be
driven low as in (1).
Timing of Recovery from Hardware Standby Mode: Drive the RES signal low approximately
100 ns before STBY goes high.
STBY
t ≥ 100 ns
RES
479
tOSC
Appendix F Product Code Lineup
Table F H8/3004 and H8/3005 Series Product Code Lineup
Product Type
H8/3004
H8/3005
ROM
less
version
ROM
less
version
Package
(Hitachi
Package
Code)
Product Code
Mark Code
Order Code Name
HD6413004F
HD6413004F
HD6413004F
80-pin QFP
(FP-80A)
I specification HD6413004TEi
HD6413004TEi
HD6413004Xi
80-pin TQFP
(TFP-80C)
Standard
products
HD6413005F
HD6413005F
80-pin QFP
(FP-80A)
HD6413005TEi
HD6413005Xi
80-pin TQFP
(TFP-80C)
Standard
products
HD6413005F
I specification HD6413005TEi
480
Appendix G Package Dimensions
Figure G-1 shows the FP-80A package dimensions of the H8/3004 and H8/3005, and figure G-2
shows the TFP-80C package dimensions.
Unit: mm
17.2 ± 0.3
14.0
60
41
40
0.65
17.2 ± 0.3
61
80
21
1
+0.08
–0.05
1.60
0.17
3.05 Max
+0.20
–0.16
2.70
0.12 M
0 – 5°
0.10
0.10
0.30 ± 0.10
20
0.80 ± 0.30
Figure G-1 Package Dimensions (FP-80A)
481
Unit: mm
14.0 ± 0.2
12.0
60
41
40
80
21
0.50
14.0 ± 0.2
61
1
20
1.00
0.10
0.50 ± 0.10
0.17 ± 0.05
1.20 Max
0.10 M
0.00 Min
0.20 Max
0.20 ± 0.05
Figure G-2 Package Dimensions (TFP-80C)
482
0 – 5°
Hitachi Microcomputer H8/3004, 3005
Publication Date:
Published by:
1st Edition, September 1995
Semiconductor and IC Div.
Hitachi, Ltd.
Edited by:
Technical Document Center
Hitachi Microcomputer System Ltd.
Copyright © Hitachi, Ltd., 1995. All rights reserved. Printed in Japan.