NUP3115UPMU Transient Voltage Suppressors Low Capacitance ESD Protection for High Speed Data The three−line voltage transient suppressor array is designed to protect voltage−sensitive components that require ultra−low capacitance from ESD and transient voltage events. This device features a common anode design which protects three independent high speed data lines and a VCC power line in a single six−lead UDFN low profile package. Excellent clamping capability, low capacitance, low leakage, and fast response time make these parts ideal for ESD protection on designs where board space is at a premium. Because of its low capacitance, it is suited for use in high frequency designs such as a USB 2.0 high speed. http://onsemi.com D1 D2 D3 6.8V VCC 6.8V 6.8V 16V Features • • • • • • • • • • Low Capacitance 0.8 pF UDFN Package, 1.6 x 1.6 mm Low Profile of 0.50 mm for Ultra Slim Design Stand Off Voltage: 5.5 V Low Leakage Protects up to Three Data Lines Plus a VCC Pin VCC Pin = 15 V Protection D1, D2, and D3 Pins = 6.4 V Minimum Protection IEC61000−4−2: Level 4 ESD Protection This is a Pb−Free Device MARKING DIAGRAM 1 P3 M G = Specific Device Code = Date Code = Pb−Free Package PIN CONNECTIONS USB 2.0 High−Speed Interface Cell Phones MP3 Players SIM Card Protection D1 1 D2 2 GND D3 3 MAXIMUM RATINGS (TJ = 25°C, unless otherwise specified) Symbol P3 MG G (Note: Microdot may be in either location) Typical Applications • • • • 1 UDFN6 1.6x1.6 MU SUFFIX CASE 517AP 6 Rating Value Unit IPK Peak Pulse Current VCC Diode 8x20 msec double exponential waveform 5.0 A TJ Operating Junction Temperature Range −40 to 125 °C Device TSTG Storage Temperature Range −55 to 150 °C NUP3115UPMUTAG TL Lead Solder Temperature – Maximum (10 seconds) 260 °C ESD IEC 61000−4−2 Contact 8000 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 6 VCC 5 NC 4 NC ORDERING INFORMATION Package Shipping† UDFN6 3000/Tape & Reel (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. See Application Note AND8308/D for further description of survivability specs. © Semiconductor Components Industries, LLC, 2011 August, 2011− Rev. 2 1 Publication Order Number: NUP3115UPMU/D NUP3115UPMU ELECTRICAL CHARACTERISTICS I (TA = 25°C unless otherwise noted) IPP Maximum Reverse Peak Pulse Current VC Clamping Voltage @ IPP VRWM IR Working Peak Reverse Voltage VC VBR VRWM Maximum Reverse Leakage Current @ VRWM VBR Test Current IF Forward Current VF Forward Voltage @ IF Ppk Peak Power Dissipation V IR VF IT Breakdown Voltage @ IT IT C IF Parameter Symbol IPP Max. Capacitance @ VR = 0 and f = 1.0 MHz Uni−Directional TVS *See Application Note AND8308/D for detailed explanations of datasheet parameters. ELECTRICAL CHARACTERISTICS (TJ = 25°C, unless otherwise specified) Parameter Symbol Min Typ Max Unit Reverse Working Voltage (D1, D2, and D3) (Note 1) Conditions VRWM1 − − 5.5 V Reverse Working Voltage (VCC) (Note 1) VRWM2 − − 12 V Breakdown Voltage (D1, D2, and D3) IT = 1 mA, (Note 2) VBR 6.0 6.8 8.0 V Breakdown Voltage (VCC) IT = 1 mA, (Note 2) VBR2 15 16 16.8 V Reverse Leakage Current (D1, D2, and D3) @ VRWM1 IR − − 1.0 mA Reverse Leakage Current (D1, D2, and D3) @ 3.3 V IR − − 85 nA Reverse Leakage Current (VCC) @ VRWM2 IR − − 1.0 mA Clamping Voltage (D1, D2, and D3) IPP = 1 A VC − 9.4 − V Clamping Voltage (VCC) IPP = 1 A VC − 18.5 − V Clamping Voltage (VCC) IPP = 3 A VC − 22 − V Junction Capacitance (D1, D2, and D3) VR = 0 V, f = 1 MHz (Line to GND) CJ − 0.8 1.0 pF Clamping Voltage Per IEC 61000−4−2 (Note 4) VC Figure 1 and 2 V 1. TVS devices are normally selected according to the working peak reverse voltage (VRWM), which should be equal or greater than the DC or continuous peak operating voltage level. 2. VBR is measured at pulse test current IT. 3. Surge current waveform per Figure 5. 4. Typical waveform. For test procedure see Figures 3 and 4 and Application Note AND8307/D. Figure 1. ESD Clamping Voltage Screenshot Positive 8 kV Contact per IEC61000−4−2 Figure 2. ESD Clamping Voltage Screenshot Negative 8 kV Contact per IEC61000−4−2 http://onsemi.com 2 NUP3115UPMU IEC61000−4−2 Waveform IEC 61000−4−2 Spec. Ipeak Level Test Voltage (kV) First Peak Current (A) Current at 30 ns (A) Current at 60 ns (A) 1 2 7.5 4 2 2 4 15 8 4 3 6 22.5 12 6 4 8 30 16 8 100% 90% I @ 30 ns I @ 60 ns 10% tP = 0.7 ns to 1 ns Figure 3. IEC61000−4−2 Spec ESD Gun Oscilloscope TVS 50 W Cable 50 W Figure 4. Diagram of ESD Test Setup The following is taken from Application Note AND8308/D − Interpretation of Datasheet Parameters for ESD Devices. systems such as cell phones or laptop computers it is not clearly defined in the spec how to specify a clamping voltage at the device level. ON Semiconductor has developed a way to examine the entire voltage waveform across the ESD protection diode over the time domain of an ESD pulse in the form of an oscilloscope screenshot, which can be found on the datasheets for all ESD protection diodes. For more information on how ON Semiconductor creates these screenshots and how to interpret them please refer to AND8307/D. ESD Voltage Clamping For sensitive circuit elements it is important to limit the voltage that an IC will be exposed to during an ESD event to as low a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per the IEC61000−4−2 waveform. Since the IEC61000−4−2 was written as a pass/fail spec for larger % OF PEAK PULSE CURRENT 100 PEAK VALUE IRSM @ 8 ms tr 90 PULSE WIDTH (tP) IS DEFINED AS THAT POINT WHERE THE PEAK CURRENT DECAY = 8 ms 80 70 60 HALF VALUE IRSM/2 @ 20 ms 50 40 30 tP 20 10 0 0 20 40 t, TIME (ms) 60 Figure 5. 8 X 20 ms Pulse Waveform http://onsemi.com 3 80 NUP3115UPMU PACKAGE DIMENSIONS UDFN6, 1.6x1.6, 0.5P CASE 517AP−01 ISSUE O A B D 2X 0.10 C PIN ONE REFERENCE 2X E DETAIL A OPTIONAL CONSTRUCTION 0.10 C A (A3) DETAIL B 0.05 C A1 0.05 C SIDE VIEW DETAIL A 6X C A1 SEATING PLANE DIM A A1 A3 b D E e D2 E2 K L L1 MOLD CMPD EXPOSED Cu TOP VIEW 6X L L1 ÉÉÉ ÉÉÉ NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. ÉÉÉ ÉÉÉ A3 DETAIL B OPTIONAL CONSTRUCTION SOLDERMASK DEFINED MOUNTING FOOTPRINT* D2 L 1 MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.20 0.30 1.60 BSC 1.60 BSC 0.50 BSC 1.10 1.30 0.45 0.65 0.20 −−− 0.20 0.40 0.00 0.15 1.26 3 E2 6X 6X K 6 5 6X 0.52 b e 0.10 C A B BOTTOM VIEW 0.05 C NOTE 3 0.61 1.90 1 0.50 PITCH 6X 0.32 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 4 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NUP3115UPMU/D