B1S thru B10S MINI SURFACE MOUNT GLASS PASSIVATED RECTIFIERS VOLTAGE - 100 TO 1000 VOLTS CURRENT - 0.5 AMPERES FEATURES MECHANICAL DATA Plastic material used carries Underwiters Laboratory recognition 94V-0 Low leakage Surge overload rating-30 amperes peak Ldeal for printed circuit board Exceeds environmental standards of MMIL-S-19500 Case Reliable low cost construction utilizing molded plastic technique results in inexpensive product Terminals Lead solderable per MIL-STD-202, Method 208 Polarity Polarity symbols molded or marking on body. Mounting position Any Weight 0.008 ounce, 0.22gram MAXIMUM RATIXGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temp. unless otherwise specified Single phase, half sine wave, 60Hz, resistive or inductive load For capacitive load, derate current by 20% B1S B2S B4S B6S B8S B10S UNITS 100 200 400 600 800 1000 Volts Maximum RMS Bridge input Voltage 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage 100 200 400 600 800 1000 Volts Maximum Recurrent Peak Reverse Voltage Maximum Average Forward on glass-epoxy P.C.B (Note 1) Current TA=300C on aluminum substrate (Note 3) 0.5 0.8 Amps Peak Forward Surge Current, 8.3ms Single Half Sine-Wave Superimposed on Rated Load 30 Amps I2 t Rating fusing (t<8.35ms) 5 A2t Maximum Forward Voltage Drop per Bridge Element at 0.5A 1 V Maximum Reverse Current at Rated TJ=250C DC Blocking Voltage per element TJ=1250C 5 Typical Junction capacitance per leg (Note 1) CJ 25 Typical Thermal resistance per leg (Note 2) R 85 JA A pF 0 C/W Operating Temperature Range TJ -55 to +150 0 Storage Temperature Range TA -55 to +150 0 C C NOTES 1. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts 2. Thermal Resestance From Junction to Ambient and from junction to lead mounted on P.C.B with 0.05 x 0.05 (13x13mm) copper pads. 3. On alum substrate P.C.B with an rea of 0.8x0.8x0.25 (20x20x6.4mm) mounte on 0.05x0.05 (13x13mm) solder pad. www.paceleader.tw 1 B1S thru B10S MINI SURFACE MOUNT GLASS PASSIVATED RECTIFIERS RATING AND CHARACTERISTICS CURVES B1S THRU B10S Fig. 2 - MAXIMUM NON-REPETITIVE SURGE CURRENT 1.0 PEAK RFORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES Fig. 1 - FORWARD CURRENT DERATING CURVE 0.8 0.6 0.4 MOUNTED ON PC BOARD SINGLE PHASE HALF WAVE 60Hz 0.2 RESISTIVE OR INDUCTIVE LOAD 0.1 20 40 60 100 120 140 160 40 30 20 10 Pulse Width 8.3ms Single Half-Sine-Wave (JEDEC METHOD) 0 1 AMBIENT TEMPERATURE, oC 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz Fig. 4 - TYPICAL FORWARD CHARACTERISTICS Fig. 5 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (mA) 100 o TJ=125 C 10 1.0 o TJ=25 C 1.0 0.1 0.1 TJ=25oC PULSE WIDTH:300 S 0.01 0 0.01 0 20 40 60 80 100 120 0.2 0.4 0.6 140 Fig. 3 - TYPICAL JUNCTION CAPACITANCE CAPACITANCE, (pF) 100 10 TJ=25oC, f=1MHz 1.0 4 10.0 REVERSE VOLTAGE, VOLTS www.paceleader.tw 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 1 0.8 2 100 1.8