Miniature Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 6A @ 125V AC & 3A @ 250V AC 4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Logic/Power Level (gold over silver): Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts and case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold; 50,000 operations minimum for silver at 3A @ 125V AC 25° Materials & Finishes Rotaries B Actuator Clip & Mounting Frame: Body Frame: Case: Movable Contactor: Movable Contacts: Stationary Contacts: Slides Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M Terminals: Stainless Steel Stainless steel Diallyl phthalate resin (UL94V–0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; or copper or brass with gold plating Environmental Data Tactiles Operating Temp Range: Humidity: Vibration: Processing Soldering: Touch Tilt Shock: Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Actuator must be in OFF (center) position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL: UL94V–0 for case File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL ” before first dash in part number to order UL recognized switch. All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” before first dash in part number to order CSA certified switch. All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. Supplement Accessories Indicators Cleaning: –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) B62 www.nkkswitches.com Distinctive Characteristics B Pushbuttons Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. Rockers Toggles Series M Miniature Rockers Programmable Illuminated PB High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. The molded diallyl phthalate case has a UL 94V-0 flammability rating. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Keylocks Prominent external insulating barriers increase insulation resistance and dielectric strength. Slides Rotaries Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Page B64 Bracket PC Mount Page B72 Flat Frame Mount Page B83 Indicators Snap-in Mount www.nkkswitches.com B63 Supplement Accessories Actual Size Touch Tilt Tactiles Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. Series M TYPICAL SWITCH B M20 1 TJ 2 W F 01 Poles Rockers & Paddles 1 SPDT 2 DPDT SP3T 2 ON F .450” (11.43mm) Wide Rocker Terminals G .450” (11.43mm) Wide Paddle 01 Solder Lug S 02 Quick Connect .453” (11.5mm) False Illluminated Rocker in Black only 03 .250” (6.35mm) Straight PC 05 .425” (10.8mm) Wirewrap Rocker & Paddle Colors 06 .750” (19.05mm) Wirewrap A Black .964” (24.5mm) Wirewrap B White 07 C Red 08 1.062” (27.0mm) Wirewrap E Yellow Mounting Frame TJ Snap-in Frame Circuits NONE ON 3 ON OFF ON 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON F Green *6 (ON) ON (ON) G Blue *7 ON ON (ON) H Gray ( ) = Momentary Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Snap-In Mount Miniature Rockers Contact Materials & Ratings W Silver; Rated 6A @ 125V AC & 3A @ 250V AC G Gold; Rated 0.4VA max @ 28V AC/DC max A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max Touch Tilt Tactiles * 3-ON circuits DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2012TJW01-FC-1A Accessories Red .450” (11.43mm) Wide Rocker Black Bezel without LED SPDT ON-NONE-ON Circuit Snap-in Frame Silver Contacts with 6–Amp Rating Supplement Solder Lug Terminals B64 www.nkkswitches.com C Series M ORDERING EXAMPLE A Bezel with 2 Round LEDs 4 Bezel with 2 Rectangular LEDs White E Yellow F Green G Blue H Gray A Black A Programmable Illuminated PB B 1 LED C Red F Green 2 LEDs Black Top LED Bottom LED C Red C Red E Yellow E Yellow F Green F Green Tactiles 3 Black Keylocks Bezel with 1 Round LED A IMPORTANT: Touch Tilt Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Red .450” (11.43mm) Wide Rocker Indicators M2012TJW01-FC-3A-CF Top LED Red Bottom LED Green Snap-in Frame Accessories 2 Bezel without LED LED Colors Black Bezel with 2 Round LEDs SPDT ON-NONE-ON Circuit Silver Contacts with 6–Amp Rating Solder Lug Terminals Supplement 1 Bezel Colors Rotaries Optional Bezels Pushbuttons B Slides 1 Rockers Toggles Snap-In Mount Miniature Rockers www.nkkswitches.com B65 Series M Toggles Snap-In Mount Miniature Rockers POLES & CIRCUITS Rocker Position ) = Momentary Programmable Illuminated PB Pushbuttons Rockers ( B Connected Terminals Down Center Up Down Pole Model SP M2012 M2013 M2015 M2018 M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 M2025 M2028 M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) DP Throw & Schematics Center Up Note: Terminal numbers are not actually on the switch. SPDT 2-3 OPEN 2 (COM) 2-1 3 1 DPDT 2-3 5-6 OPEN 2 2-1 5-4 3 (COM) 1 5 6 4 For 3 Throw (3-On) Pole Model Down Center Up SP M2024 M2026 M2027 ON (ON) ON ON ON ON ON (ON) (ON) Rotaries Keylocks Connected Terminals & Schematic External Connection 2 (in) 5 Slides 1 (out) 3 4 (out) 6 (out) 2-3 5-6 External Connection 2 (in) 5 1 (out) External Connection The SP3T model utilizes a double pole base. External Connection 2 (in) 5 3 4 (out) 6 (out) 1 (out) 2-3 5-4 3 4 (out) 6 (out) External connection must be made during field installation. (out) External Conn 6 3 5 2 4 1 (out) Common (in) (out) 2-1 5-4 Tactiles TJ Tilt MOUNTING FRAME (18.0) .710 Panel Cutout for Single Pole without Bezel Snap-in Frame Touch Panel Cutout for Double Pole without Bezel (12.5) .492 25° (2.54) Dia .100 (12.2) .480 (15.9) .626 (4.3) .170 (15.9) .626 (13.1) .516 Panel Thickness without Bezel: .039” ~ .126” (1.0mm ~ 3.2mm) Panel Thickness with Bezel: .039” ~ .098” (1.0mm ~ 2.5mm) Accessories Indicators CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: See Supplement section to find complete explanation of operating range. Supplement A Gold over Silver Power Level or Logic Level 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. B66 www.nkkswitches.com Series M TERMINALS .062” (1.57mm) Wide Quick Connect 02 (4.0) .157 (2.0) .079 (2.0) (1.1) .079 .043 Thk = (0.8) .031 (1.57) .062 Thk = (0.8) .031 (4.8) .189 .250” (6.35mm) Straight PC 3 (6.35) (4.8) .250 .189 Epoxy Seal 2 (4.7) Typ .185 1 .425” (10.8mm) Wirewrap or Extended PC 06 .750” (19.05mm) Wirewrap or Extended PC 07 .964” (24.5mm) Wirewrap or Extended PC 08 1.062” (27.0mm) Wirewrap or Extended PC 6 2 5 1 4 (1.8) Dia Typ .073 (1.17) .046 Thk = (0.8) .031 05 3 (4.7) Typ .185 Programmable Illuminated PB 03 B (6.35) .250 Epoxy Seal Pushbuttons Epoxy Seal (1.8) Dia Typ .073 Single Pole Double Pole If using as extended PC terminal, refer to the above footprints. Epoxy Seal A Dimension A = Keylocks Solder Lug terminal lengths as shown beside the terminal codes at the left. (1.27) .050 Thk = (0.8) .031 Rotaries 01 (9.19) .362 Material: Polyamide Finish: Matte (11.43) .450 (16.36) .644 (5.84) R .230 Colors Available: A, B, C, E, F, G, H (11.43) .450 (11.8) .465 (1.8) .071 Touch (1.8) .071 (11.8) .465 AT466 .453” (11.5mm) False Illuminated Rocker (8.6) .339 False Illuminator Acrylonitrile Butadiene Styrene (11.3) .445 Indicators Material: Finish: Colors: Rocker Polycarbonate Glossy Black (7.7) .303 White and Red (1.8) .071 (11.5) .453 Accessories S (2.36) .093 Material: Polyamide Finish: Matte (7.11) (6.3) .280 .248 Colors Available: A, B, C, E, F, G, H AT4151 .450” (11.43mm) Wide Paddle Tactiles G Tilt AT4150 .450” (11.43mm) Wide Rocker Slides ROCKERS & PADDLES F (11.8) .465 A Black B White C Red E Yellow www.nkkswitches.com F Green G Blue H Supplement When a bezel is selected with AT466, glossy polycarbonate AT207 is supplied. Cap Colors Available: Rockers Toggles Snap-In Mount Miniature Rockers Gray B67 Series M OPTIONAL SNAP-IN BEZELS & BEZEL COLORS 1 B AT2107 Bezel AT208 Bezel for AT070 LED Material: Polycarbonate Yellow A (11.8) .465 (19.0) .748 Single Pole Double Pole Gray (15.6) .614 AT212 Bezel for AT617 LED A (13.1)mm .516” B (6.25)mm .246” (6.55)mm .258” A (12.0) .472 (10.0) .394 Finish: Semi-glossy (8.0) .315 Tilt Touch Finish: Semi-glossy (10.0) .394 (8.0) .315 A (15.9) .626 A Single Pole Double Pole A A (12.0) .472 (2.2) .087 (18.4)mm .724” Black (21.5) Sq .846 (18.7)mm .736” (15.9) .626 LED colors & specifications on next page. (7.8) .307 (11.8) .465 (5.0) Typ .197 (15.9) .626 LED colors & specifications on next page. (2.2) .087 (7.8) .307 (11.8) .465 (21.5) Sq .846 (2.0) Typ .079 (8.8) Dia .346 A Single Pole Double Pole A (18.4)mm .724” (18.7)mm .736” Bezel Assembly 1. Pry out tab on bezel to a 45° angle. Accessories Indicators AT213 Bezel for AT618 LED (13.1)mm .516” (13.8) .543 Black Tactiles (3.0) Dia Typ .118 (12.5)mm .492” B (12.5)mm .492” (30.2) 1.19 (5.4) Dia .213 Material: Polycarbonate A LED colors & specifications on next page. (12.0) .472 Contact factory for matte finish. 4 A Blue Single Pole Double Pole Finish: Glossy 3 H (15.9) .626 Green Black (2.2) .087 (13.5) .531 Material: Polycarbonate Slides E (21.5) .846 G White (12.0) .472 (15.6) .614 F Black B (2.2) .087 Finish: Matte 2 A (11.8) .465 Material: Polyamide Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Snap-In Mount Miniature Rockers Tab 2. Insert switch frame under tab and snap on bezel. 3. Push tab back into place. 45° Supplement Tab B68 www.nkkswitches.com 4. Snap assembled bezel and switch into panel. Series M Toggles Snap-In Mount Miniature Rockers LED COLORS & SPECIFICATIONS B (5.0) .197 (5.0) .197 Top LED Circuit Mark This Side Circuit Mark This Side Top LED Bottom LED (7.0) .276 (+) (-) Bottom LED Programmable Illuminated PB (7.7) .303 Pushbuttons (3.0) Dia .118 (-) (+) (-) (+) Note: Lead lengths may differ from manufacturing lot to lot. The longer lead is the anode (+). AT617 AT618 Keylocks AT070 C F C E F C E F Color Red Green Red Yellow Green Red Yellow Green Maximum Forward Current IFM 25mA 50mA 30mA 30mA 25mA 25mA 30mA 25mA Typical Forward Current IF 20mA 30mA 20mA 20mA 20mA 20mA 20mA 20mA Forward Voltage VF 2.8V 2.1V 2.0V 2.1V 2.2V 2.25V 2.1V 2.2V Maximum Reverse Voltage VRM 4V 5V 5V 5V 5V 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.33 mA/°C 0.40 mA/°C 0.40 mA/°C 0.40 mA/°C 0.33 mA/°C 0.33 mA/°C 0.40 mA/°C 0.33 mA/°C (-) Ambient Temperature Range (when used with a bezel) –10° ~ +70°C –15° ~ +70°C –25° ~ +70°C Tactiles (+) The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is independent of switch operation. LED is colored in OFF state. Tilt If the source voltage is greater than the rated voltage of the LED, a ballast resistor must be connected in series with the lamp. The ballast resistor calculation and more lamp detail are shown in the Supplement section. Touch LEGENDS Indicators NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Area for Cap (0.76) Typ .030 Pad Print Epoxy based ink is recommended. (4.5) Typ .177 AT4150 www.nkkswitches.com (9.91) .390 (11.43) .450 Accessories Recommended Print Method: (0.38) Typ .015 (0.76) Typ (3.36) Typ .132 .030 Supplement F OF ON Rotaries (5.08) Dia .200 AT618 LED For Bezel AT213 with 2 Rectangular LEDs Slides AT617 LED For Bezel AT212 with 2 Round LEDs Circuit Mark This Side AT070 LED For Bezel AT208 with 1 LED Rockers Bezel Orientation on Switch Shaded areas are printable areas. B69 Series M Toggles Snap-In Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS (4.9) .194 (2.8) Circuit Mark .110 This Side (1.1) x (2.0) Typ .043 x .079 3 (18.0) .709 (4.7) Typ .185 25° (0.5) .020 (7.1) .279 (3.3) .130 (13.0) .512 2 (0.8) Typ .031 (11.43) .450 (12.2) .480 1 (2.0) Typ .079 (0.5) .020 (9.4) .371 (7.9) .311 (4.5) .177 M2012TJW01-FC Snap-in Frame • Solder Lug Double Pole (4.9) .194 Keylocks Programmable Illuminated PB Single Pole B Pushbuttons Rockers Snap-in Frame • Solder Lug Rotaries (18.0) .709 (2.8) Circuit Mark .110 This Side (4.7) Typ .185 25° (0.8) Typ .031 (11.43) .450 (12.2) .480 (0.5) .020 (7.1) .279 (3.3) .130 (4.8) .189 (1.1) x (2.0) Typ .043 x .079 3 6 5 2 4 1 (13.0) .512 (0.5) .020 (9.4) .371 (2.0) Typ .079 (4.5) .177 (12.7) .500 Slides M2022TJW01-FC Snap-in Frame • Solder Lug Single Pole Circuit Mark This Side Tactiles (2.8) .110 (1.1) x (2.0) Typ .043 x .079 3 (18.0) .709 (4.7) Typ .185 25° (2.36) .093 (3.18) .125 (13.7) .539 Snap-in Frame • Solder Lug (2.0) Typ .079 (0.5) .020 (9.4) .371 (7.9) .311 (4.5) .177 Double Pole (2.8) .110 Circuit Mark This Side (4.8) .189 (1.1) x (2.0) Typ .043 x .079 6 (18.0) .709 Accessories Supplement (0.5) .020 (7.1) .279 M2012TJW01-GC Indicators Touch Tilt (0.8) Typ .031 (11.43) .450 (12.2) .480 (13.0) .512 2 1 (4.7) Typ .185 25° (0.8) Typ .031 (2.36) .093 (11.43) .450 (12.2) .480 (3.18) .125 (13.7) .539 M2022TJW01-GC B70 www.nkkswitches.com (0.5) .020 (7.1) .279 (9.4) .371 (4.5) .177 (0.5) .020 3 5 2 4 1 (12.7) .500 (13.0) .512 (2.0) Typ .079 Series M Toggles Snap-In Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS (4.8) .189 1 (0.8) Typ .031 (4.3) .169 (2.2) .087 (6.4) .252 (4.01) .158 (9.4) .371 Double Pole (4.9) .193 Circuit Mark (1.1) x (2.0) Typ This Side .043 x .079 (13.5) .531 (12.0) .472 (2.5) .098 (0.61) Sq .024 (4.7) Typ .185 25° (0.8) Typ .031 (11.43) .450 (11.8) .465 (15.6) .614 (4.3) .169 (2.2) .087 (6.4) .252 (4.01) .158 (5.6) .221 (7.8) .307 3 2 4 1 (0.5) .020 (4.5) .177 (9.4) .371 (13.0) .512 (14.0) .551 (2.0) Typ .079 (4.8) .189 (12.7) .500 Single Pole (10.0) .394 6 5 Keylocks (30.2) 1.190 M2012TJW01-FC-1A Snap-in Frame • AT208 Bezel • Solder Lug (15.3) Min .602 (19.0) .748 1 Rotaries (5.08) Dia .200 4 (13.0) .512 (14.0) .551 (12.7) .500 (7.9) .311 (4.5) .177 2 (2.0) Typ .079 (2.0) .079 (0.5) .020 5 M2022TJW01-FC-2A-C Snap-in Frame • AT212 Bezel • Solder Lug Circuit Mark This Side (1.1) x (2.0) Typ .043 x .079 Tactiles (11.43) .450 (11.8) .465 (15.6) .614 (13.0) .512 (14.0) .551 2 Pushbuttons (4.7) Typ .185 25° 3 (8.0) .315 (12.0) .472 (4.7) Typ .185 25° (13.0) .512 (14.0) .551 2 (0.8) Typ .031 1 (4.01) .158 (9.4) .371 (4.5) .177 (0.5) .020 Double Pole (10.0) .394 (5.6) .221 (7.8) .307 (8.0) .315 (12.0) .472 Circuit Mark This Side (2.0) .079 (7.9) .311 M2012TJW01-FC-3A-CF Snap-in Frame • AT213 Bezel • Solder Lug (1.1) x (2.0) Typ .043 x .079 (4.7) Typ .185 25° (0.8) Typ .031 6 3 5 2 4 1 (13.0) .512 Indicators (4.3) .169 (2.2) .087 (6.4) .252 (14.0) .551 Accessories (11.43) .450 (11.8) .465 (21.5) Sq .846 Tilt (3.0) Dia Typ .118 (5.0) Typ .197 (2.0) .079 (11.43) .450 (11.8) .465 (21.5) Sq .846 (4.01) .158 (4.3) .169 (2.2) .087 (6.4) .252 (0.5) .020 (9.4) .371 (4.5) .177 (4.8) .189 (12.7) .500 (2.0) Typ .079 M2022TJW01-FC-4A-CF www.nkkswitches.com Touch (12.0) .472 B71 Supplement (21.5) .846 B 3 6 3 Programmable Illuminated PB Circuit Mark This Side Rockers Snap-in Frame • AT2107 Bezel • Solder Lug (1.1) x (2.0) Typ .043 x .079 Slides Single & Double Pole (5.6) .221 Series M TYPICAL SWITCH M20 B Pushbuttons Rockers Toggles Bracket PC Mount Miniature Rockers 1 3 Slides G Mounting Frames 1 SPDT 2 DPDT SP3T 3 3PDT (used only with terminal codes 30 & 41 & frame code TX) 4 4PDT DP3T (used only with terminal code 41 & frame code TX) TX Narrow Frame for Small Actuator TZ Wide Frame for Large Actuator Contact Materials & Ratings Circuits 2 ON NONE ON 3 ON OFF ON 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON *6 (ON) ON (ON) *7 ON ON (ON) Rotaries Keylocks Programmable Illuminated PB Poles TX W Silver; Rated 6A @ 125V AC & 3A @ 250V AC G Gold; Rated 0.4VA max @ 28V AC/DC max A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max ( ) = Momentary Touch Tilt Tactiles * 3-ON circuits DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2013TXG41-DC Accessories SPDT ON-OFF-ON Circuit Gold Contacts with 0.4VA Rating TX Frame with .365” (9.27mm) Wide Red Rocker Supplement .150” (3.81mm) Vertical PC Terminals with Support B72 www.nkkswitches.com Series M ORDERING EXAMPLE Terminals For TX & TZ Frames Rockers & Paddles Straight PC with Bracket (1-2 Pole only) Small Actuators (TX Frame) Rocker & Paddle Colors A Black White C Red E .365” (9.27mm) Wide Paddle E Yellow F Green F .450” (11.43mm) Wide Rocker G Blue H Gray G .450” (11.43mm) Wide Paddle 15 .425” (10.8mm) Straight PC with .630” (16.0mm) Bracket 17 .964” (24.5mm) Straight PC with 1.150” (29.2mm) Bracket 23 .250” (6.35mm) Straight PC with .465” (11.8mm) Bracket 25 .425” (10.8mm) Straight PC with .630” (16.0mm) Bracket J .595” (15.11mm) Wide Rocker 26 .750” (19.05mm) Straight PC with .953” (24.2mm) Bracket H .595” (15.11mm) Wide Paddle Keylocks B D Straight PC with Reinforced Bracket (1-2 Pole only) B .365” (9.27mm) Wide Rocker .250” (6.35mm) Straight PC with .465” (11.8mm) Bracket Slides Rotaries Large Actuators (TZ Frame) Terminals For TX Frame Only Right Angle PC with Support (1-3 Pole only) Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings and ordering instructions are noted on the General Specifications page. .150” (3.81mm) Right Angle PC Touch .150” (3.81mm) Vertical PC DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2022TZG23-JC TZ Frame with .595” (15.11mm) Wide Red Rocker DPDT ON-NONE-ON Circuit Accessories 41 Tilt Vertical PC with Support (1-4 Pole) Gold Contacts with 0.4VA Rating .250” (6.35mm) Straight PC Terminals with Reinforced Bracket www.nkkswitches.com Supplement 30 IMPORTANT: Tactiles 13 C Pushbuttons D Programmable Illuminated PB 41 Rockers Toggles Bracket PC Mount Miniature Rockers B73 Series M Toggles Bracket PC Mount Miniature Rockers POLES & CIRCUITS Rocker Position ) = Momentary B Programmable Illuminated PB Down Center Up Down Model SP M2012 M2013 *M2015 M2018 *M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 *M2025 M2028 *M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 *M2025 M2028 *M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 M2042 M2043 *M2045 M2048 *M2049 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 11-12 DP 3P Rotaries Keylocks Connected Terminals Pole Pushbuttons Rockers ( Slides 4P Center Throw & Schematics Up Note: Terminal numbers are not actually on the switch. * Reverse circuits available for vertical mount SP & DP upon request. SPDT 2-3 OPEN 2 (COM) 2-1 3 1 DPDT 2-3 5-6 OPEN 2 2-1 5-4 (COM) 3 5 1 6 4 3PDT 2-1 5-4 8-7 OPEN 2 3 5 1 (COM) 6 4 8 9 7 8 11 4PDT 2-1 5-4 8-7 11-10 OPEN 5 2 3 1 (COM) 9 4 6 7 12 10 Tilt Tactiles For 3 Throw (3-On) Connected Terminals & Schematics Pole SP Model M2024 M2026 M2027 Down Center ON (ON) ON ON ON ON Up ON (ON) (ON) Down Center External Connection 2 (in) 5 External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) 1 (out) M2044 M2046 M2047 ON (ON) ON Accessories DP The SP3T model utilizes a double pole base. Supplement Indicators Touch 2-3 5-6 External connection must be made during field installation. B74 ON ON ON External Connection 2 (in) 5 ON (ON) (ON) External Conn External Connection 2 (in) 5 External Connection 8 (in) 11 2-3 5-6 8-9 11-12 6 3 5 2 4 1 (out) 3 4 (out) 6 (out) 1 (out) 2-1 5-4 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 2-3 5-4 8-9 11-10 External connection must be made during field installation. www.nkkswitches.com External Connection 8 (in) 11 External Connection 2 (in) 5 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) Common (in) 3 4 (out) 6 (out) 1 (out) External Connection 8 (in) 11 The DP3T model utilizes a four pole base. (out) External Connection 2 (in) 5 2-3 5-4 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) (out) Up 2-1 5-4 8-7 11-10 (out) External Conn Common (in) (out) (out) 12 9 11 8 5 2 10 7 4 1 (out) 6 3 (out) Common (in) (out) Series M MOUNTING FRAMES Narrow Mounting Frame for Small Actuators with Straight PC Terminals (codes 13, 15, 17, 23, 25, & 26) or with Angle PC Terminals (codes 30 & 41) (2.54) Dia .100 (8.0) .315 (1.4) Typ .055 (3.5) .138 25° 25° (2.54) Dia .100 (2.54) Dia .100 (4.37) .172 (0.4) Typ .016 (5.08) .200 (2.75) .108 Pushbuttons (5.08) .200 25° B Vertical PC Mounting (6.0) .235 (1.27) .050 Small Actuators & Panel Cutouts for TX Frame (actuator details on the following pages) AT4149 AT4150 (12.7) .500 TZ Wide Mounting Frame for Large Actuators with Straight PC Terminals (codes 13, 15, 17, 23, 25, & 26) Rotaries (12.4) .490 (10.1) .398 Direction of Actuation Direction of Actuation (17.8) .701 AT4151 Large Actuators & Panel Cutouts for TZ Frame (actuator details on the following pages) AT4156 Slides AT4148 Programmable Illuminated PB Right Angle PC Mounting Keylocks Straight PC Mounting AT4157 (2.54) Dia .100 Tilt (3.5) .138 Direction of Actuation (28.5) 1.122 25° Tactiles TX Rockers Toggles Bracket PC Mount Miniature Rockers (16.0) .630 Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Indicators W Touch CONTACT MATERIALS & RATINGS Gold over Silver Power Level or Logic Level 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Supplement A Accessories Note: See Supplement section to find complete explanation of operating range. Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. www.nkkswitches.com B75 Series M TERMINALS For TX and TZ 1-2 Pole Straight PC Mount with Bracket B 13 15 .250” (6.35mm) Terminal with .465” (11.8mm) Bracket For TX and TZ 1-2 Pole Straight PC Mount with Reinforced Bracket 17 .425” (10.8mm) Terminal with .630” (16.0mm) Bracket 23 .964” (24.5mm) Terminal with 1.150” (29.2mm) Bracket 25 .250” (6.35mm) Terminal with .465” (11.8mm) Bracket 26 .425” (10.8mm) Terminal with .630” (16.0mm) Bracket .750” (19.05mm) Terminal with .953” (24.2mm) Bracket Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Bracket PC Mount Miniature Rockers PCB footprints are on the following Typical Switch Dimension pages. For TX 1-3 Pole Right Angle PC Mount .150” (3.81mm) Right Angle PC 41 .150” (3.81mm) Vertical PC ROCKERS & PADDLES FOR TX MOUNTING FRAMES D AT4148 .365” (9.27mm) Wide Rocker Material: Polyamide Finish: Matte E (9.27) .365 Tilt Tactiles Slides Rotaries 30 For TX 1-4 Pole Vertical PC Mount AT4149 .365” (9.27mm) Wide Paddle (9.27) (16.87) .664 (13.49) .531 (2.13) .084 .365 Material: Polyamide Finish: Matte (3.96) .156 (18.8) .740 Touch (3.5) .138 Material: Polyamide Finish: Matte G (11.43) .450 AT4151 .450” (11.43mm) Wide Paddle (2.36) .093 (11.43) .450 Material: Polyamide Finish: Matte (11.8) .465 (9.19) .362 (3.18) .125 (16.36) .644 (7.7) .303 (8.1) (6.3) .319 .248 Supplement (3.5) .138 Cap Colors Available: B76 A Black B White C Red (3.5) .138 (16.8) .661 AT4150 .450” (11.43mm) Wide Rocker Accessories Indicators F (8.43) R .332 (8.8) .346 (7.9) (6.15) .311 .242 (5.84) R .230 (11.8) .465 E www.nkkswitches.com Yellow F Green G Blue H Gray (3.5) .138 Series M ROCKERS & PADDLES FOR TZ MOUNTING FRAMES AT4156 .595” (15.11mm) Wide Rocker H B Material: Polyamide Finish: Matte (2.36) .093 (14.33) .564 (26.78) 1.054 (29.82) 1.174 (23.01) .906 (7.3) .287 (3.5) .138 A (13.5) R .531 (11.0) .433 (8.4) (6.5) .331 .256 Black B White Programmable Illuminated PB (4.75) .187 (15.11) .595 Cap Colors Available: Pushbuttons Material: Polyamide Finish: Matte AT4157 .595” (15.11mm) Wide Paddle C E Red Yellow (3.5) .138 (26.8) 1.055 (15.11) .595 F Green G Blue H Gray Keylocks J OPTIONAL SNAP-IN PANEL FRAMES Material: Polyamide Finish: Matte Color: Black (25.04) .986 (15.62) .615 Tactiles (6.68) .263 Mounted separately from switches A B Tilt Cutout Tolerances: Dimension A: .797” ~ .803” (20.24 ~ 20.4mm) Dimension B: .495” ~ .505” (12.57 ~ 12.83mm) (2.3) .090 (9.9) .390 (17.9) .705 Slides AT064-2 Accommodates .062” ~ .125” (1.57 ~ 3.18mm) panel thickness Rotaries Used with AT4148 Rocker and AT4149 Paddle AT064-1 Accommodates .047” ~ .090” (1.2 ~ 2.3mm) panel thickness Rockers Toggles Bracket PC Mount Miniature Rockers AT064–1 Enlarged Detail Material: Polyamide Finish: Matte Color: Black (15.62) .615 (12.0) .472 (2.3) .090 (19.43) .765 Accessories (6.68) .263 Mounted separately from switches Cutout Tolerances: Dimension A: .595” ~ .605” (15.11 ~ 15.37mm) Dimension B: .495” ~ .500” (12.57 ~ 12.7mm) (12.8) .504 Indicators AT065-2 Accommodates .062” ~ .125” (1.57 ~ 3.18mm) panel thickness A B AT065–1 Enlarged Detail www.nkkswitches.com AT065–2 Enlarged Detail B77 Supplement AT065-1 Accommodates .047” ~ .090” (1.2 ~ 2.3mm) panel thickness Touch Used with AT4150 Rocker and AT4151 Paddle Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Straight PC • Bracket B Programmable Illuminated PB TE RMI NAL LE NGTH Single Pole Double Pole Circuit Mark This Side (3.5) .138 B R AC KE T LE N GT H 2 1 (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (8.0) .315 (15.8) .622 (4.8) .189 (3.2) Typ .126 (12.7) .500 M2012TXG13-DC Keylocks Terminal Code: Rotaries Slides (8.8) .346 (6.15) .242 Pushbuttons Rockers 25° Terminal Length: Bracket Length: (1.6) Typ .063 (2.4) Typ .095 (1.6) Typ .063 13 .250” (6.35mm) .465” (11.8mm) 15 .425” (10.8mm) .630” (16.0mm) 17 .964” (24.5mm) 1.150” (29.2mm) (7.9) Typ .311 (4.7) Typ .185 3 (7.9) Typ .311 2 (4.7) Typ .185 1 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Straight PC • Reinforced Bracket 25° (8.8) .346 Tactiles (6.15) .242 Tilt Touch (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 Double Pole Circuit Mark This Side (3.5) .138 TE RMI NAL LE NGTH Single Pole B R AC KE T LE N GT H 2 1 (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (9.1) .358 (19.05) .750 (12.7) .500 (6.35) Typ .250 (4.8) .189 Terminal Code: Terminal Length: Bracket Length: Accessories 23 .250” (6.35mm) .465” (11.8mm) 25 .425” (10.8mm) .630” (16.0mm) Supplement Indicators M2012TXG23-DC 26 .750” (19.05mm) .953” (24.2mm) B78 www.nkkswitches.com (2.4) Typ .095 (3.18) Typ .125 (3.18) Typ .125 (9.53) Typ .375 3 (9.53) Typ .375 2 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 1 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS B 1 2 3 (7.9) .311 (9.27) .365 (5.41) .213 3 2 (4.7) Typ .185 1 (4.3) .169 (0.4) .016 (2.85) .112 (1.4) Typ .055 (5.08) .200 (5.5) .217 (4.0) .157 (12.7) .500 (6.15) .242 (8.8) .346 (1.27) .050 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 Pushbuttons Pivot Programmable Illuminated PB Shown in Down Position (1.8) Dia Typ .073 (2.54) Typ .100 M2012TXG30-DC Double Pole Shown in Down Position (9.27) .365 5 6 1 2 3 (12.7) .500 6 5 4 3 2 1 (6.15) .242 (0.4) Typ .016 (4.0) .157 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 (3.81) .150 (2.54) Typ .100 (1.8) Dia Typ .073 Tactiles (8.8) .346 (1.27) Typ .050 (3.81) .150 (4.7) Typ .185 (12.7) .500 (4.3) .169 (2.85) .112 (1.4) Typ .055 (5.08) .200 Rotaries Pivot Slides (6.4) .252 .150” (3.81mm) Right Angle PC 4 Rockers .150” (3.81mm) Right Angle PC Keylocks Single Pole Shown in Down Position Pivot 9 4 5 6 1 2 9 (17.5) .689 (6.15) .242 (8.8) .346 (0.4) .016 (4.5) .177 (14.35) .565 (1.27) Typ .050 (3.81) Typ .150 7 6 5 4 3 2 1 (4.7) Typ .185 (3.81) Typ .150 3 (4.3) .169 (2.85) .112 (1.4) Typ .055 (5.08) .200 8 Indicators 8 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 (14.35) .565 Accessories (9.27) .365 7 (2.54) Typ .100 (1.8) Dia Typ .073 Supplement (8.8) .346 .150” (3.81mm) Right Angle PC Touch Three Pole M2032TXG30-DC www.nkkswitches.com Tilt M2022TXG30-DC B79 Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Rockers .150” (3.81mm) Vertical PC Single Pole B (8.8) .346 (9.27) .365 (3.5) .138 3 Pushbuttons 25° (9.1) .360 (3.81) Typ .150 1 (3.18) .125 (12.7) .500 (1.27) .050 (12.7) .500 (2.74) .108 Shown in (6.15) (5.97) Down Position .242 .235 (0.4) Typ .016 (5.08) .200 (0.8) Typ .031 (3.81) Typ .150 (1.27) .050 (7.9) .311 (2.54) Typ .100 (1.8) Dia Typ .073 M2012TXG41-DC .150” (3.81mm) Vertical PC Double Pole (9.27) .365 (8.8) .346 Keylocks Programmable Illuminated PB 2 (13.0) .512 (3.5) .138 25° (9.1) .360 Rotaries (0.4) Typ .016 (5.08) .200 (1.27) .050 (12.7) .500 3 5 2 4 (3.18) .125 (2.74) .108 (6.15) (5.97) Shown in Down Position .242 .235 6 (0.8) Typ .031 (3.81) Typ .150 (13.0) .512 1 3 6 2 5 1 4 (2.4) Typ .094 (3.81) Typ .150 (12.7) .500 (1.27) Typ .050 (4.8) .189 (12.7) .500 (2.54) Typ .100 (1.8) Dia Typ .073 Slides M2022TXG41-DC .150” (3.81mm) Vertical PC Three Pole (9.27) .365 Tactiles (8.8) .346 (3.5) .138 25° (9.1) .360 Tilt (0.4) Typ .016 (5.08) .200 9 6 3 8 5 2 7 4 1 (13.0) .512 3 6 9 2 5 8 1 4 7 (3.18) .125 (2.74) .108 Shown in Down Position (6.15) (5.97) .242 .235 (1.27) .050 (14.35) .565 (2.54) Typ .100 (1.8) Dia Typ .073 Four Pole (9.27) .365 Indicators Touch M2032TXG41-DC .150” (3.81mm) Vertical PC (8.8) .346 (3.5) .138 25° Accessories (9.1) .360 Supplement (0.4) Typ .016 (5.08) .200 (2.74) .108 (6.15) (5.97) Shown in Down Position .242 .235 12 9 6 3 11 8 5 2 10 7 4 (13.0) .512 1 (3.18) .125 (1.27) .050 (14.35) .565 M2042TXG41-DC B80 (3.81) Typ .150 (14.35) .565 (1.27) Typ .050 (4.8) Typ .189 (17.5) .689 (0.8) Typ .031 (3.81) Typ .150 (4.8) Typ .189 www.nkkswitches.com (0.8) Typ .031 (3.81) Typ .150 3 6 9 12 2 5 8 11 1 4 7 10 (4.8) Typ .189 (3.81) Typ .150 (14.35) .565 (4.8) Typ .189 (22.3) .878 (1.27) Typ .050 (2.54) Typ .100 (1.8) Dia Typ .073 Series M Toggles Bracket PC Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS 25° 2 Pushbuttons B R AC KE T LE N GT H (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (15.8) .622 (8.0) .315 (12.7) .500 Programmable Illuminated PB 1 (0.6) Typ .024 (0.8) Typ .031 (4.7) Typ .185 B Double Pole Circuit Mark This Side (3.5) .138 T ERMIN A L LEN G T H Single Pole (4.8) .189 (3.2) Typ .126 3 (7.9) Typ .311 (7.9) Typ .311 2 (4.7) Typ .185 3 6 2 5 1 4 (4.7) Typ .185 1 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.8) Dia Typ .073 (1.5) Dia Typ .059 CL Terminal Code: Terminal Length: Bracket Length: 13 .250” (6.35mm) .465” (11.8mm) 15 .425” (10.8mm) .630” (16.0mm) 17 .964” (24.5mm) 1.150” (29.2mm) Rotaries (1.6) Typ .063 (2.4) Typ .095 (1.6) Typ .063 Keylocks M2012TZG13-JC Straight PC • Reinforced Bracket Slides (11.0) .433 (6.6) .260 Rockers Straight PC • Bracket 25° Tactiles (4.8) Typ .189 3 (1.17) Typ .046 (1.17) Typ .046 (19.05) .750 (9.1) .358 (12.7) .500 (6.35) Typ .250 (4.8) .189 Touch 2 1 BRACKET LENGTH (9.53) Typ .375 3 (9.53) Typ .375 2 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 1 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Terminal Code: Terminal Length: Bracket Length: 23 .250” (6.35mm) .465” (11.8mm) 25 .425” (10.8mm) .630” (16.0mm) 26 .750” (19.05mm) .953” (24.2mm) www.nkkswitches.com Accessories (2.4) Typ .095 (3.18) Typ .125 (3.18) Typ .125 Indicators M2012TZG23-JC Supplement (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 Double Pole Circuit Mark This Side (3.5) .138 T E RMIN A L LENGTH Single Pole Tilt (11.0) .433 (6.6) .260 B81 Series M Toggles Bracket PC Mount Miniature Rockers LEGENDS Rockers NKK Switches can provide custom legends for caps. Contact factory for more information. B Pushbuttons Suggested Printable Area for Cap AT4148 AT4150 ON ON F OF F OF F OF Programmable Illuminated PB ON Keylocks (0.38) Typ .015 (6.9) Typ .272 (0.76) Typ .030 (5.76) Typ .227 (7.75) .305 Rotaries (9.27) .365 AT4156 (0.76) Typ .030 (0.38) Typ .015 (4.5) Typ .177 (0.76) Typ .030 (0.76) Typ .030 (3.36) Typ .132 Slides Recommended Print Method: Pad Print Epoxy based ink is recommended. Supplement Accessories Indicators Touch Tilt Tactiles (10.03) Typ .395 (11.18) Typ .440 (9.91) .390 (11.43) .450 Shaded areas are printable areas. B82 (0.38) Typ .015 www.nkkswitches.com (0.76) Typ .030 (13.59) .535 (15.11) .595 (0.76) Typ .030 Series M TYPICAL SWITCH ORDERING EXAMPLE 1 2 TN W 01 Poles C B Rockers & Paddles Mounting Frames 4 4PDT DP3T TY .504” (12.8mm) Wide Flat Frame Contact Materials & Ratings Circuits 2 ON NONE ON 3 ON OFF ON 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON *6 (ON) ON (ON) *7 ON ON (ON) W Silver; Rated 6A @ 125V AC & 3A @ 250V AC G Gold; Rated 0.4VA max @ 28V AC/DC max A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max E .365” (9.27mm) Wide Paddle F .450” (11.43mm) Wide Rocker G .450” (11.43mm) Wide Paddle Large Actuators (TY Frame) J .595” (15.11mm) Wide Rocker H .595” (15.11mm) Wide Paddle Rocker & Paddle Colors Terminals ( ) = Momentary * 3-ON circuits Programmable Illuminated PB 3PDT .365” (9.27mm) Wide Rocker 01 Solder Lug 03 .250” (6.35mm) Straight PC IMPORTANT: A Black B White C Red E Yellow F Green G Blue H Gray Tilt Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings and ordering instructions are noted on the General Specifications page. Keylocks 3 D Rotaries TN Slides DPDT SP3T Small Actuators (TN Frame) Tactiles 2 .272” (6.9mm) Wide Flat Frame Touch SPDT DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2012TNW01-DC Accessories Red .365” (9.27mm) Wide Rocker .272” (6.9mm) Wide Flat Frame SPDT ON-NONE-ON Circuit Silver Contacts with 6-Amp Rating Solder Lug Terminals www.nkkswitches.com Supplement 1 D Pushbuttons M20 Rockers Toggles Flat Frame Mount Miniature Rockers B83 Series M Toggles Flat Frame Mount Miniature Rockers POLES & CIRCUITS Rocker Position ) = Momentary B Center Up M2012 M2013 M2015 M2018 M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 M2025 M2028 M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2032 M2033 M2035 M2038 M2039 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2042 M2043 M2045 M2048 M2049 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) Model SP DP 3P 4P Connected Terminals Down Pole Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers ( Down Center Throw & Schematics Up Note: Terminal numbers are not actually on the switch. SPDT 2-3 OPEN 2 (COM) 2-1 3 1 DPDT 2-3 5-6 OPEN 2 2-1 5-4 (COM) 3 1 5 6 4 3PDT 2-3 5-6 8-9 2-1 5-4 8-7 OPEN 2 3 5 1 (COM) 6 4 8 9 7 8 11 4PDT 2-3 5-6 8-9 11-12 2-1 5-4 8-7 11-10 OPEN 5 2 3 1 (COM) 9 4 6 7 12 10 For 3 Throw (3-On) Tilt Tactiles Connected Terminals & Schematics Pole SP Model M2024 M2026 M2027 Down Center ON (ON) ON ON ON ON Up ON (ON) (ON) Down Center External Connection 2 (in) 5 External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) 1 (out) Touch 2-3 5-6 Supplement Accessories Indicators DP M2044 M2046 M2047 ON (ON) ON ON ON ON External Connection 2 (in) 5 ON (ON) (ON) External Connection 5 2 (in) External Connection 8 (in) 11 2-3 5-6 8-9 11-12 External connection must be made during field installation. B84 6 3 5 2 4 1 (out) 1 (out) 2-1 5-4 External Connection 11 8 (in) (out) 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 2-3 5-4 8-9 11-10 2-1 5-4 8-7 11-10 (out) External Conn Common (in) External connection must be made during field installation. www.nkkswitches.com External Connection 8 (in) 11 External Connection 2 (in) 5 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) Common (in) 3 4 (out) 6 (out) 1 (out) 3 4 (out) 6 (out) The DP3T model utilizes a four pole base. (out) External Conn External Connection 2 (in) 5 2-3 5-4 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) The SP3T model utilizes a double pole base. Up (out) (out) 12 9 11 8 5 2 10 7 4 1 (out) 6 3 (out) Common (in) (out) Series M MOUNTING FRAMES (6.9) .272 B Pushbuttons (3.5) .138 (29.5) (23.8) 1.161 .937 (0.6) .024 Programmable Illuminated PB Mounting hardware kit HK-1, as shown on the following page, must be ordered separately. (2.4) Dia Typ .094 Small Actuators & Panel Cutouts for TN Frame (actuator details on the following pages) AT4149 AT4150 AT4151 (17.8) .701 (23.8) .937 (10.1) .398 TY (12.7) .500 (23.8) .937 (2.6) Dia Typ .102 (12.4) .490 (2.6) Dia Typ .102 Large Actuators & Panel Cutout for TY Frame (actuator details on the following pages) .504” (12.8mm) Wide Flat Frame AT4157 Tactiles AT4156 Slides AT4148 Keylocks .272” (6.9mm) Wide Flat Frame Rotaries TN Rockers Toggles Flat Frame Mount Miniature Rockers Touch Tilt Mounting hardware kit HK-2, as shown on the following page, must be ordered separately. (3.2) Dia Typ .126 www.nkkswitches.com (3.5) Dia Typ .138 Supplement (16.0) .630 Accessories (28.5) 1.122 (34.9) 1.374 (41.3) (34.9) 1.626 1.374 (0.6) .024 Indicators (12.8) .504 (3.5) .138 B85 Series M Toggles Flat Frame Mount Miniature Rockers MOUNTING FRAMES (CONTINUED) Subpanel Mounting B Pushbuttons Rockers Face Panel Mounting Programmable Illuminated PB S TANDOFF LE NGTH Flat frame devices may also be mounted to the face panel. Standoffs are used to recess the actuator and achieve an attractive front panel appearance. These devices are especially designed for subpanel mounting. When installed on a mounting plate behind the panel, hardware is completely concealed and the front panel retains a clean, attractive appearance. Optional Snap-in Panel Frames Optional Hardware Kits for Subpanel or Face Panel Mounting Panel Thickness Frame Standoff Length Further details are shown in the previous bracketed PC mount subsection. Hardware Kit Number TN Frame .125” (3.175mm) .233” (5.918mm) ATHK-1 TY Frame .125” (3.175mm) .312” (7.925mm) ATHK-2 Keylocks Hardware kits include: 2 stainless steel screws, 2 hex nuts, 2 lockwashers, & 2 standoffs AT064-1 AT064-2 AT065-1 AT065-2 W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Slides Rotaries CONTACT MATERIALS & RATINGS Note: See Supplement section to find complete explanation of operating range. Tactiles A Power Level or Logic Level Gold over Silver 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. Tilt TERMINALS Touch 01 Solder Lug (4.0) .157 Epoxy Seal (2.0) .079 Indicators (2.0) (1.1) .079 .043 Thk = (0.8) .031 03 .250” (6.35mm) Straight PC (4.8) .189 Accessories 3 2 Epoxy Seal (6.35) (4.8) .250 .189 Supplement (1.17) .046 Thk = (0.8) .031 B86 (4.7) Typ .185 1 (1.8) Dia Typ .073 Single Pole 3 6 2 5 1 4 (4.7) Typ .185 (1.8) Dia Typ .073 Double Pole www.nkkswitches.com 3 6 9 2 5 8 1 4 7 (4.8) Typ .189 (4.7) Typ .185 (1.8) Dia Typ .073 Three Pole 3 6 9 12 2 5 8 11 1 4 7 10 (4.8) Typ .189 (4.7) Typ .185 (1.8) Dia Typ .073 Four Pole Series M Toggles Flat Frame Mount Miniature Rockers ROCKERS & PADDLES AT4148 .365” (9.27mm) Wide Rocker AT4149 .365” (9.27mm) Wide Paddle E (2.13) .084 (9.27) .365 (16.87) .664 (13.49) .531 (3.96) .156 (18.8) .740 (3.5) .138 Keylocks AT4151 .450” (11.43mm) Wide Paddle G Material: Polyamide Finish: Matte (2.36) .093 (11.43) .450 (11.8) .465 (9.19) .362 (3.18) .125 (16.36) .644 (7.7) .303 (8.1) (6.3) .319 .248 Rotaries Material: Polyamide Finish: Matte (11.43) .450 (3.5) .138 (16.8) .661 AT4150 .450” (11.43mm) Wide Rocker F (8.43) R .332 (8.8) .346 (7.9) (6.15) .311 .242 (3.5) .138 (5.84) R .230 Slides (9.27) .365 Pushbuttons Material: Polyamide Finish: Matte Programmable Illuminated PB Material: Polyamide Finish: Matte B (3.5) .138 (11.8) .465 Tactiles D For TY Frame AT4156 .595” (15.11mm) Wide Rocker H Tilt Material: Polyamide Finish: Matte (2.36) .093 (14.33) .564 Touch Material: Polyamide Finish: Matte AT4157 .595” (15.11mm) Wide Paddle (29.82) 1.174 (23.01) .906 (8.4) (6.5) .331 .256 (7.3) .287 (3.5) .138 Cap Colors Available: A (13.5) R .531 (11.0) .433 Black B White (26.8) 1.055 (15.11) .595 C Red E Yellow F www.nkkswitches.com Green G Blue Accessories (26.78) 1.054 Indicators (4.75) .187 (15.11) .595 (3.5) .138 H Supplement J Rockers For TN Frame Gray B87 Series M Toggles Flat Frame Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Rockers TN Frame • Solder Lug Single Pole (2.4) Dia Typ .094 (12.3) .484 B (3.5) .138 Circuit Mark This Side (1.1) x (2.0) Typ .043 x. 079 3 TN Frame • Solder Lug (0.6) .024 (10.3) .406 1 (0.5) .020 (2.0) .079 (7.9) .311 (4.5) .177 Double Pole (2.4) Dia Typ .094 (12.3) .484 (2.0) Typ .079 (1.1) x (2.0) Typ .043 x. 079 (3.5) .138 Circuit Mark This Side Rotaries (29.5) 1.161 (23.8) .937 (4.7) Typ .185 25° (0.8) Typ .031 (7.9) .311 (9.65) .380 (6.9) .272 (9.27) .365 M2022TNW01-DC TN Frame • Solder Lug (0.6) .024 (10.3) .406 (4.5) .177 6 3 5 2 4 1 (0.5) .020 (13.0) .512 (4.8) .189 (12.7) .500 Three Pole (12.3) .484 (2.4) Dia Typ .094 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 (2.0) Typ .079 Circuit Mark This Side Tactiles Slides (7.9) .311 (9.65) .380 (13.0) .512 2 (0.8) Typ .031 (6.9) .272 (9.27) .365 M2012TNW01-DC (4.7) Typ .185 25° (29.5) 1.161 Keylocks Programmable Illuminated PB Pushbuttons (23.8) .937 (23.8) .937 (4.7) Typ .185 25° (29.5) 1.161 6 3 8 5 2 7 4 1 (13.0) .512 Touch Tilt (0.8) Typ .031 9 (7.9) .311 (9.65) .380 (6.9) .272 (9.27) .365 M2032TNW01-DC TN Frame • Solder Lug (0.5) .020 (4.8) Typ .189 (4.5) .177 (17.5) .689 Four Pole (12.3) .484 Indicators (2.4) Dia Typ .094 (1.1) x (2.0) Typ .043 x .079 (3.5) .138 (2.0) Typ .079 Circuit Mark This Side (23.8) .937 (29.5) 1.161 Accessories Supplement (0.6) .024 (12.4) .488 M2042TNW01-DC B88 (4.7) Typ .185 25° (0.8) Typ .031 (6.9) .272 (7.9) .311 (9.27) .365 (9.65) .380 www.nkkswitches.com 9 6 3 11 8 5 2 10 7 4 1 (0.5) .020 (0.6) .024 (12.4) .488 12 (4.5) .177 (13.0) .512 (4.8) Typ .189 (22.3) .878 Series M Toggles Flat Frame Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Double Pole B 3 (4.7) Typ .185 25° 2 (0.8) Typ .031 (12.8) .504 (15.11) .595 (8.4) .331 (10.0) .394 (0.6) .024 (10.0) .394 (4.5) .177 (13.0) .512 6 3 5 2 4 1 1 (0.5) .020 (7.9) .311 (2.0) .079 (4.8) .189 (13.0) .512 (2.0) Typ .079 Double pole has barrier between terminals. Three Pole (14.5) .571 M2012TYW01-JC TY Frame • Solder Lug (2.0) Typ .079 (1.1) x (2.0) Typ .043 x .079 (3.5) .138 Rotaries (3.2) Dia Typ .126 Programmable Illuminated PB (41.3) 1.626 (34.9) 1.374 Pushbuttons Circuit Mark This Side Circuit Mark This Side 25° (0.8) Typ .031 (8.4) .331 (12.8) .504 (15.11) .595 (10.0) .394 (0.6) .024 (12.1) .476 6 3 8 5 2 7 4 1 (13.0) .512 Slides (41.3) 1.626 (4.7) Typ .185 (0.5) .020 (4.8) Typ .189 (4.5) .177 (17.5) .689 M2032TYW01-JC Four Pole (14.5) .571 TY Frame • Solder Lug (2.0) Typ .079 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 Touch (3.2) Dia Typ .126 Tactiles 9 (34.9) 1.374 25° (0.8) Typ .031 (12.8) .504 (15.11) .595 (8.4) .331 (10.0) .394 (0.6) .024 (12.1) .476 (0.5) .020 (4.5) .177 6 3 11 8 5 2 10 7 4 1 (22.3) .878 (13.0) .512 Accessories (41.3) 1.626 9 (4.8) Typ .189 Supplement 12 (4.7) Typ .185 Indicators Circuit Mark This Side (34.9) 1.374 Rockers Single Pole (1.1) x (2.0) Typ .043 x .079 (3.5) .138 Tilt (14.5) .571 (3.2) Dia Typ .126 TY Frame • Solder Lug Keylocks M2042TYW01-JC www.nkkswitches.com B89 Series M Toggles Flat Frame Mount Miniature Rockers LEGENDS B Suggested Printable Area for Caps Pushbuttons Rockers NKK Switches can provide custom legends for caps. Contact factory for more information. AT4148 AT4150 ON ON F OF F OF F OF Programmable Illuminated PB ON Keylocks (0.38) Typ .015 (6.9) Typ .272 Rotaries (0.76) Typ .030 (5.76) Typ .227 (7.75) .305 (9.27) .365 AT4156 (0.76) Typ .030 (0.38) Typ .015 (4.5) Typ .177 (0.76) Typ .030 (9.91) .390 (11.43) .450 (0.76) Typ .030 (3.36) Typ .132 Slides Recommended Print Method: Pad Print Tactiles (10.03) Typ .395 (11.18) Typ .440 Shaded areas are printable areas. Supplement Accessories Indicators Touch Tilt Epoxy based ink is recommended. B90 (0.38) Typ .015 www.nkkswitches.com (0.76) Typ .030 (13.59) .535 (15.11) .595 (0.76) Typ .030