Hermetic Infrared Emitting Diode OP215, OP216 Features: • • • • • Hermetically sealed package OP216 Mechanically and spectrally matched to other OPTEK devices Designed for direct mount to PCBoard Enhanced temperature range OP215 Excellent coupling efficiency Description: Each OP215 and OP216 device is an 890 nm gallium aluminum arsenide infrared emitting diode (GaAIAs), mounted in a hermetically sealed “pig tale” package with an enhanced temperature range and a narrow irradiance pattern that provides high on-axis intensity for excellent coupling efficiency. These devices offer significantly higher power output than GaAs at equivalent drive currents and have a wavelength that is matched to silicon’s peak response. Their small package size permits high device density mounting. The OP216 series devices provide an additional mounting tab connected to the Cathode/Case. All these LEDs are mechanically and spectrally matched to the OP300 series, OP516, OP600 series and OP640 series devices. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data, and to Application Bulletin 202 for pill-type soldering to PCBoard. Ordering Information Applications: • • • • • • Non-contact reflective object sensor Assembly line automation Part Number OP215A OP215B OP215C OP215D Machine automation Machine safety End of travel sensor OP216A OP216B OP216C OP216D LED Peak Wavelength Optical Power mW/cm2 (Min) Total Beam Angle 890 mm 1.20 0.60 0.30 0.20 24° Door sensor 1 Pin # LED 1 2 Anode Cathode 2 RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A 06/08 Page 1 of 3 Hermetic Infrared Emitting Diode OP215, OP216 Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage Temperature Range -65o C to +150o C Operating Temperature Range -65o C to +125o C 2.0 V Reverse Voltage Continuous Forward Current 100 mA Peak Forward Current (2µs pulse with 0.1% duty cycle) 1.0 A Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C(1)(2) Power Dissipation 150 mW(3) Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN Apertured Radiant Incidence OP216A OP216B OP216C OP216D 1.20 0.60 0.30 0.20 TYP MAX - - UNITS TEST CONDITIONS Input Diode EE (APT)(3) mW/cm2 IF = 50 mA(4) VF Forward Voltage - - 1.80 V IF = 50 mA IR Reverse Current - - 100 µA VR= 2.0 V λP Wavelength at Peak Emission - 890 - nm IF = 10 mA B Spectral Bandwidth between Half Power Points - 80 - nm IF = 10 mA Spectral Shift with Temperature - +0.18 - nm/°C ∆λP /∆T θHP Emission Angle at Half Power Points - 24 - IF = Constant Degree IF = 50 mA tr Output Rise Time - 500 - ns tf Output Fall Time - 250 - ns IF(PK)=100 mA, PW=10 µs, and D.C.=10.0% Notes: 1. Refer to Application Bulletin 202 which reviews proper soldering techniques for pill-type devices. 2. No clean or low solids. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. 3. Derate linearly 1.50 mW/° C above 25° C. 4. For OP216, EE(APT) is a measurement using a 0.180” (4.57 mm) diameter apertured sensor placed 0.653” (16.59 mm) from the lens tip. EE(APT) is not necessarily uniform within the measured area. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 06/08 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Hermetic Infrared Emitting Diode OP215, OP216 OP215 & OP216 Forward Voltage vs Forward Current vs Temperature Optical Power vs IF vs Temperature 1.8 2.0 1.7 1.8 Normalized at 50 mA and 20° C Normalized Optical Power Typical Forward Voltage (V) -60° C -40° C -20° C 0° C 20° C 40° C 60° C 80° C 100° C 120° C 1.6 1.6 1.5 1.4 1.3 -60° C -40° C -20° C 0° C 20° C 40° C 60° C 80° C 100° C 120°C 1.2 1.1 1.0 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.9 0.0 0 5 10 15 20 25 30 35 40 45 50 0 5 10 15 Distance vs Output Power vs Forward Current 25 30 35 40 45 50 Normalized Intensity vs Beam Angle 6 1.1 1.0 Normalized at 1" and 50 mA 5 0.9 Forward Current Angular Displacement (° Degrees) Normalized Output Power 20 Forward Current IF (mA) Forward Current (mA) 10 mA 20 mA 30 mA 40 mA 50 mA 60 mA 70 mA 80 mA 90 mA 100 mA 4 3 2 1 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0.2 '' 0.0 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 '' -45 -35 -25 -15 Distance (inches) -5 5 15 25 35 45 Normalized Intensity OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A 06/08 Page 3 of 3