ATMEL AT89S8252-24JI 8-bit microcontroller with 8k bytes flash Datasheet

Features
• Compatible with MCS-51™ Products
• 8K Bytes of In-System Reprogrammable Downloadable Flash Memory
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
– SPI Serial Interface for Program Downloading
– Endurance: 1,000 Write/Erase Cycles
2K Bytes EEPROM
– Endurance: 100,000 Write/Erase Cycles
4V to 6V Operating Range
Fully Static Operation: 0 Hz to 24 MHz
Three-level Program Memory Lock
256 x 8-bit Internal RAM
32 Programmable I/O Lines
Three 16-bit Timer/Counters
Nine Interrupt Sources
Programmable UART Serial Channel
SPI Serial Interface
Low-power Idle and Power-down Modes
Interrupt Recovery From Power-down
Programmable Watchdog Timer
Dual Data Pointer
Power-off Flag
8-bit
Microcontroller
with 8K Bytes
Flash
AT89S8252
Description
The AT89S8252 is a low-power, high-performance CMOS 8-bit microcomputer with
8K bytes of downloadable Flash programmable and erasable read only memory and
2K bytes of EEPROM. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard 80C51
instruction set and pinout. The on-chip downloadable Flash allows the program memory to be reprogrammed in-system through an SPI serial interface or by a
conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU
with downloadable Flash on a monolithic chip, the Atmel AT89S8252 is a powerful
microcomputer which provides a highly-flexible and cost-effective solution to many
embedded control applications.
The AT89S8252 provides the following standard features: 8K bytes of downloadable
Flash, 2K bytes of EEPROM, 256 bytes of RAM, 32 I/O lines, programmable watchdog timer, two data pointers, three 16-bit timer/counters, a six-vector two-level
interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry. In
addition, the AT89S8252 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode
stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM contents but
freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset.
The downloadable Flash can be changed a single byte at a time and is accessible
through the SPI serial interface. Holding RESET active forces the SPI bus into a serial
programming interface and allows the program memory to be written to or read from
unless Lock Bit 2 has been activated.
Rev. 0401E–02/00
1
Pin Configurations
PDIP
P1.4 (SS)
P1.3
P1.2
P1.1 (T2 EX)
P1.0 (T2)
NC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P2.4 (A12)
P2.3 (A11)
P2.2 (A10)
P2.1 (A9)
P2.0 (A8)
(MOSI) P1.5
(MISO) P1.6
(SCK) P1.7
RST
(RXD) P3.0
NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
6
5
4
3
2
1
44
43
42
41
40
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
7
8
9
10
11
12
13
14
15
16
17
39
38
37
36
35
34
33
32
31
30
29
18
19
20
21
22
23
24
25
26
27
28
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
NC
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
(WR) P3.6
(RD) P3.7
XTAL2
XTAL1
GND
NC
(A8) P2.0
(A9) P2.1
(A10) P2.2
(A11) P2.3
(A12) P2.4
(T2) P1.0
(T2 EX) P1.1
P1.2
P1.3
(SS) P1.4
(MOSI) P1.5
(MISO) P1.6
(SCK) P1.7
RST
(RXD) P3.0
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
(WR) P3.6
(RD) P3.7
XTAL2
XTAL1
GND
PLCC
44
43
42
41
40
39
38
37
36
35
34
P1.4 (SS)
P1.3
P1.2
P1.1 (T2 EX)
P1.0 (T2)
NC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
PQFP/TQFP
33
32
31
30
29
28
27
26
25
24
23
1
2
3
4
5
6
7
8
9
10
11
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
NC
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
(WR) P3.6
(RD) P3.7
XTAL2
XTAL1
GND
GND
(A8) P2.0
(A9) P2.1
(A10) P2.2
(A11) P2.3
(A12) P2.4
12
13
14
15
16
17
18
19
20
21
22
(MOSI) P1.5
(MISO) P1.6
(SCK) P1.7
RST
(RXD) P3.0
NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
Pin Description
program and data memory. In this mode, P0 has internal
pullups.
VCC
GND
Port 0 also receives the code bytes during Flash programmi ng an d ou tpu ts th e c ode by te s d ur i ng p r og r am
verification. External pullups are required during program
verification.
Ground.
Port 1
Port 0
Port 1 is an 8-bit bi-directional I/O port with internal pullups.
The Port 1 output buffers can sink/source four TTL inputs.
When 1s are written to Port 1 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 1 pins that are externally being pulled low will source
current (IIL) because of the internal pullups.
Supply voltage.
Port 0 is an 8-bit open drain bbi-didirectional I/O port. As an
output port, each pin can sink eight TTL inputs. When 1s
are written to port 0 pins, the pins can be used as highimpedance inputs.
Port 0 can also be configured to be the multiplexed loworder address/data bus during accesses to external
2
AT89S8252
AT89S8252
Block Diagram
P0.0 - P0.7
P2.0 - P2.7
PORT 0 DRIVERS
PORT 2 DRIVERS
VCC
GND
EEPROM
RAM ADDR.
REGISTER
B
REGISTER
PORT 0
LATCH
RAM
PORT 2
LATCH
FLASH
PROGRAM
ADDRESS
REGISTER
STACK
POINTER
ACC
BUFFER
TMP2
TMP1
PC
INCREMENTER
ALU
INTERRUPT, SERIAL PORT,
AND TIMER BLOCKS
PROGRAM
COUNTER
PSW
PSEN
ALE/PROG
EA / VPP
TIMING
AND
CONTROL
INSTRUCTION
REGISTER
DPTR
RST
WATCH
DOG
PORT 3
LATCH
PORT 1
LATCH
SPI
PORT
PROGRAM
LOGIC
OSC
PORT 3 DRIVERS
P3.0 - P3.7
PORT 1 DRIVERS
P1.0 - P1.7
3
Some Port 1 pins provide additional functions. P1.0 and
P1.1 can be configured to be the timer/counter 2 external
count input (P1.0/T2) and the timer/counter 2 trigger input
(P1.1/T2EX), respectively.
Port 3 pins that are externally being pulled low will source
current (IIL) because of the pullups.
Port 3 also serves the functions of various special features
of the AT89S8252, as shown in the following table.
Port 3 also receives some control signals for Flash programming and verification.
Pin Description
Furthermore, P1.4, P1.5, P1.6, and P1.7 can be configured
as the SPI slave port select, data input/output and shift
clock input/output pins as shown in the following table.
Port Pin
Alternate Functions
P3.0
RXD (serial input port)
P3.1
TXD (serial output port)
P3.2
INT0 (external interrupt 0)
P3.3
INT1 (external interrupt 1)
Port Pin
Alternate Functions
P1.0
T2 (external count input to Timer/Counter 2),
clock-out
P1.1
T2EX (Timer/Counter 2 capture/reload trigger
and direction control)
P3.4
T0 (timer 0 external input)
P3.5
T1 (timer 1 external input)
P1.4
SS (Slave port select input)
P3.6
WR (external data memory write strobe)
P1.5
MOSI (Master data output, slave data input pin
for SPI channel)
P3.7
RD (external data memory read strobe)
P1.6
MISO (Master data input, slave data output pin
for SPI channel)
P1.7
SCK (Master clock output, slave clock input pin
for SPI channel)
RST
Reset input. A high on this pin for two machine cycles while
the oscillator is running resets the device.
ALE/PROG
Port 1 also receives the low-order address bytes during
Flash programming and verification.
Port 2
Port 2 is an 8-bit bi-directional I/O port with internal pullups.
The Port 2 output buffers can sink/source four TTL inputs.
When 1s are written to Port 2 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 2 pins that are externally being pulled low will source
current (IIL) because of the internal pullups.
Port 2 emits the high-order address byte during fetches
from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @
DPTR). In this application, Port 2 uses strong internal pullups when emitting 1s. During accesses to external data
memory that use 8-bit addresses (MOVX @ RI), Port 2
emits the contents of the P2 Special Function Register.
Port 2 also receives the high-order address bits and some
control signals during Flash programming and verification.
Port 3
Port 3 is an 8 bit bi-directional I/O port with internal pullups.
The Port 3 output buffers can sink/source four TTL inputs.
When 1s are written to Port 3 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
4
AT89S8252
Address Latch Enable is an output pulse for latching the
low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during
Flash programming.
In normal operation, ALE is emitted at a constant rate of 1/6
the oscillator frequency and may be used for external timing or clocking purposes. Note, however, that one ALE
pulse is skipped during each access to external data
memory.
If desired, ALE operation can be disabled by setting bit 0 of
SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is
weakly pulled high. Setting the ALE-disable bit has no
effect if the microcontroller is in external execution mode.
PSEN
Program Store Enable is the read strobe to external program memory.
When the AT89S8252 is executing code from external program memory, PSEN is activated twice each machine
cycle, except that two PSEN activations are skipped during
each access to external data memory.
EA/VPP
External Access Enable. EA must be strapped to GND in
order to enable the device to fetch code from external pro-
AT89S8252
gram memory locations starting at 0000H up to FFFFH.
Note, however, that if lock bit 1 is programmed, EA will be
internally latched on reset.
EA should be strapped to VCC for internal program executions. This pin also receives the 12-volt programming
enable voltage (VPP) during Flash programming when 12volt programming is selected.
XTAL1
Input to the inverting oscillator amplifier and input to the
internal clock operating circuit.
XTAL2
Output from the inverting oscillator amplifier.
Table 1. AT89S8252 SFR Map and Reset Values
0F8H
0F0H
0FFH
B
00000000
0F7H
0E8H
0E0H
0EFH
ACC
00000000
0E7H
0D8H
0DFH
0D0H
PSW
00000000
0C8H
T2CON
00000000
T2MOD
XXXXXX00
RCAP2L
00000000
RCAP2H
00000000
TL2
00000000
SPCR
000001XX
0D7H
TH2
00000000
0CFH
0C0H
0C7H
0B8H
IP
XX000000
0BFH
0B0H
P3
11111111
0B7H
0A8H
IE
0X000000
0A0H
P2
11111111
98H
SCON
00000000
90H
P1
11111111
88H
TCON
00000000
TMOD
00000000
TL0
00000000
TL1
00000000
TH0
00000000
TH1
00000000
80H
P0
11111111
SP
00000111
DP0L
00000000
DP0H
00000000
DP1L
00000000
DP1H
00000000
SPSR
00XXXXXX
0AFH
0A7H
SBUF
XXXXXXXX
9FH
WMCON
00000010
97H
8FH
SPDR
XXXXXXXX
PCON
0XXX0000
87H
5
Special Function Registers
A map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 1.
Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip.
Read accesses to these addresses will in general return
random data, and write accesses will have an indeterminate
effect.
User software should not write 1s to these unlisted
locations, since they may be used in future products to invoke new features. In that case, the reset or inactive values
of the new bits will always be 0.
Timer 2 Registers Control and status bits are contained in
registers T2CON (shown in Table 2) and T2MOD (shown in
Table 9) for Timer 2. The register pair (RCAP2H, RCAP2L)
are the Capture/Reload registers for Timer 2 in 16 bit capture mode or 16-bit auto-reload mode.
Table 2. T2CON—Timer/Counter 2 Control Register
T2CON Address = 0C8H
Reset Value = 0000 0000B
Bit Addressable
Bit
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2
CP/RL2
7
6
5
4
3
2
1
0
Symbol
Function
TF2
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either
RCLK = 1 or TCLK = 1.
EXF2
Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.
When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be
cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).
RCLK
Receive clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in serial port
Modes 1 and 3. RCLK = 0 causes Timer 1 overflows to be used for the receive clock.
TCLK
Transmit clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in serial port
Modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.
EXEN2
Timer 2 external enable. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if
Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.
TR2
Start/Stop control for Timer 2. TR2 = 1 starts the timer.
C/T2
Timer or counter select for Timer 2. C/T2 = 0 for timer function. C/T2 = 1 for external event counter (falling edge triggered).
CP/RL2
Capture/Reload select. CP/RL2 = 1 causes captures to occur on negative transitions at T2EX if EXEN2 = 1. CP/RL2 = 0
causes automatic reloads to occur when Timer 2 overflows or negative transitions occur at T2EX when EXEN2 = 1. When
either RCLK or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.
6
AT89S8252
AT89S8252
Watchdog and Memory Control Register The WMCON
register contains control bits for the Watchdog Timer
(shown in Table 3). The EEMEN and EEMWE bits are used
to select the 2K bytes on-chip EEPROM, and to enable
byte-write. The DPS bit selects one of two DPTR registers
available.
Table 3. WMCON—Watchdog and Memory Control Register
WMCON Address = 96H
Bit
Reset Value = 0000 0010B
PS2
PS1
PS0
EEMWE
EEMEN
DPS
WDTRST
WDTEN
7
6
5
4
3
2
1
0
Symbol
Function
PS2
PS1
PS0
Prescaler Bits for the Watchdog Timer. When all three bits are set to “0”, the watchdog timer has a nominal period of
16 ms. When all three bits are set to “1”, the nominal period is 2048 ms.
EEMWE
EEPROM Data Memory Write Enable Bit. Set this bit to “1” before initiating byte write to on-chip EEPROM with the
MOVX instruction. User software should set this bit to “0” after EEPROM write is completed.
EEMEN
Internal EEPROM Access Enable. When EEMEN = 1, the MOVX instruction with DPTR will access on-chip EEPROM
instead of external data memory. When EEMEN = 0, MOVX with DPTR accesses external data memory.
DPS
Data Pointer Register Select. DPS = 0 selects the first bank of Data Pointer Register, DP0, and DPS = 1 selects the
second bank, DP1
WDTRST
RDY/BSY
Watchdog Timer Reset and EEPROM Ready/Busy Flag. Each time this bit is set to “1” by user software, a pulse is
generated to reset the watchdog timer. The WDTRST bit is then automatically reset to “0” in the next instruction cycle.
The WDTRST bit is Write-Only. This bit also serves as the RDY/BSY flag in a Read-Only mode during EEPROM write.
RDY/BSY = 1 means that the EEPROM is ready to be programmed. While programming operations are being executed,
the RDY/BSY bit equals “0” and is automatically reset to “1” when programming is completed.
WDTEN
Watchdog Timer Enable Bit. WDTEN = 1 enables the watchdog timer and WDTEN = 0 disables the watchdog timer.
SPI Registers Control and status bits for the Serial Peripheral Interface are contained in registers SPCR (shown in
Table 4) and SPSR (shown in Table 5). The SPI data bits
are contained in the SPDR register. Writing the SPI data
register during serial data transfer sets the Write Collision
bit, WCOL, in the SPSR register. The SPDR is double buffered for writing and the values in SPDR are not changed by
Reset.
Dual Data Pointer Registers To facilitate accessing both
internal EEPROM and external data memory, two banks of
16 bit Data Pointer Registers are provided: DP0 at SFR
address locations 82H-83H and DP1 at 84H-85H. Bit DPS
= 0 in SFR WMCON selects DP0 and DPS = 1 selects
DP1. The user should always initialize the DPS bit to the
appropriate value before accessing the respective Data
Pointer Register.
Interrupt Registers The global interrupt enable bit and the
individual interrupt enable bits are in the IE register. In
addition, the individual interrupt enable bit for the SPI is in
the SPCR register. Two priorities can be set for each of the
six interrupt sources in the IP register.
Power Off Flag The Power Off Flag (POF) is located at
bit_4 (PCON.4) in the PCON SFR. POF is set to “1” during
power up. It can be set and reset under software control
and is not affected by RESET.
7
Table 4. SPCR—SPI Control Register
SPCR Address = D5H
Bit
Reset Value = 0000 01XXB
SPIE
SPE
DORD
MSTR
CPOL
CPHA
SPR1
SPR0
7
6
5
4
3
2
1
0
Symbol
Function
SPIE
SPI Interrupt Enable. This bit, in conjunction with the ES bit in the IE register, enables SPI interrupts: SPIE = 1 and ES
= 1 enable SPI interrupts. SPIE = 0 disables SPI interrupts.
SPE
SPI Enable. SPI = 1 enables the SPI channel and connects SS, MOSI, MISO and SCK to pins P1.4, P1.5, P1.6, and
P1.7. SPI = 0 disables the SPI channel.
DORD
Data Order. DORD = 1 selects LSB first data transmission. DORD = 0 selects MSB first data transmission.
MSTR
Master/Slave Select. MSTR = 1 selects Master SPI mode. MSTR = 0 selects Slave SPI mode.
CPOL
Clock Polarity. When CPOL = 1, SCK is high when idle. When CPOL = 0, SCK of the master device is low when not
transmitting. Please refer to figure on SPI Clock Phase and Polarity Control.
CPHA
Clock Phase. The CPHA bit together with the CPOL bit controls the clock and data relationship between master and
slave. Please refer to figure on SPI Clock Phase and Polarity Control.
SPR0
SPR1
SPI Clock Rate Select. These two bits control the SCK rate of the device configured as master. SPR1 and SPR0 have
no effect on the slave. The relationship between SCK and the oscillator frequency, FOSC., is as follows:
SPR1SPR0 SCK = FOSC. divided by
0 0
4
0 1
16
1 0
64
1 1
128
Table 5. SPSR – SPI Status Register
SPSR Address = AAH
Bit
Reset Value = 00XX XXXXB
SPIF
WCOL
–
–
–
–
–
–
7
6
5
4
3
2
1
0
Symbol
Function
SPIF
SPI Interrupt Flag. When a serial transfer is complete, the SPIF bit is set and an interrupt is generated if SPIE = 1 and
ES = 1. The SPIF bit is cleared by reading the SPI status register with SPIF and WCOL bits set, and then accessing
the SPI data register.
WCOL
Write Collision Flag. The WCOL bit is set if the SPI data register is written during a data transfer. During data transfer,
the result of reading the SPDR register may be incorrect, and writing to it has no effect. The WCOL bit (and the SPIF
bit) are cleared by reading the SPI status register with SPIF and WCOL set, and then accessing the SPI data register.
Table 6. SPDR – SPI Data Register
SPDR Address = 86H
Bit
8
Reset Value = unchanged
SPD7
SPD6
SPD5
SPD4
SPD3
SPD2
SPD1
SPD0
7
6
5
4
3
2
1
0
AT89S8252
AT89S8252
Data Memory – EEPROM and RAM
The AT89S8252 implements 2K bytes of on-chip EEPROM
for data storage and 256 bytes of RAM. The upper 128
bytes of RAM occupy a parallel space to the Special Function Registers. That means the upper 128 bytes have the
same addresses as the SFR space but are physically separate from SFR space.
When an instruction accesses an internal location above
address 7FH, the address mode used in the instruction
specifies whether the CPU accesses the upper 128 bytes
of RAM or the SFR space. Instructions that use direct
addressing access SFR space.
For example, the following direct addressing instruction
accesses the SFR at location 0A0H (which is P2).
MOV 0A0H, #data
Instructions that use indirect addressing access the upper
128 bytes of RAM. For example, the following indirect
addressing instruction, where R0 contains 0A0H, accesses
the data byte at address 0A0H, rather than P2 (whose
address is 0A0H).
actual timer periods (at VCC = 5V) are within ±30% of the
nominal.
The WDT is disabled by Power-on Reset and during
Power-down. It is enabled by setting the WDTEN bit in SFR
WMCON (address = 96H). The WDT is reset by setting the
WDTRST bit in WMCON. When the WDT times out without
being reset or disabled, an internal RST pulse is generated
to reset the CPU.
Table 7. Watchdog Timer Period Selection
WDT Prescaler Bits
PS2
PS1
PS0
Period (nominal)
0
0
0
16 ms
0
0
1
32 ms
0
1
0
64 ms
0
1
1
128 ms
1
0
0
256 ms
1
0
1
512 ms
1
1
0
1024 ms
1
1
1
2048 ms
MOV @R0, #data
Note that stack operations are examples of indirect
addressing, so the upper 128 bytes of data RAM are available as stack space.
The on-chip EEPROM data memory is selected by setting
the EEMEN bit in the WMCON register at SFR address
location 96H. The EEPROM address range is from 000H to
7FFH. The MOVX instructions are used to access the
EEPROM. To access off-chip data memory with the MOVX
instructions, the EEMEN bit needs to be set to “0”.
The EEMWE bit in the WMCON register needs to be set to
“1” before any byte location in the EEPROM can be written.
User software should reset EEMWE bit to “0” if no further
EEPROM write is required. EEPROM write cycles in the
serial programming mode are self-timed and typically take
2.5 ms. The progress of EEPROM write can be monitored
by reading the RDY/BSY bit (read-only) in SFR WMCON.
RDY/BSY = 0 means programming is still in progress and
RDY/BSY = 1 means EEPROM write cycle is completed
and another write cycle can be initiated.
Timer 0 and 1
Timer 0 and Timer 1 in the AT89S8252 operate the same
way as Timer 0 and Timer 1 in the AT89C51, AT89C52 and
AT89C55. For further information, see the October 1995
Microcontroller Data Book, page 2-45, section titled,
“Timer/Counters.”
Timer 2
Timer 2 is a 16 bit Timer/Counter that can operate as either
a timer or an event counter. The type of operation is
selected by bit C/T2 in the SFR T2CON (shown in Table 2).
Timer 2 has three operating modes: capture, auto-reload
(up or down counting), and baud rate generator. The
modes are selected by bits in T2CON, as shown in Table 8.
In addition, during EEPROM programming, an attempted
read from the EEPROM will fetch the byte being written
with the MSB complemented. Once the write cycle is completed, true data are valid at all bit locations.
Timer 2 consists of two 8-bit registers, TH2 and TL2. In the
Timer function, the TL2 register is incremented every
machine cycle. Since a machine cycle consists of 12 oscillator periods, the count rate is 1/12 of the oscillator
frequency.
Programmable Watchdog Timer
In the Counter function, the register is incremented in
response to a 1-to-0 transition at its corresponding external
input pin, T2. In this function, the external input is sampled
during S5P2 of every machine cycle. When the samples
show a high in one cycle and a low in the next cycle, the
count is incremented. The new count value appears in the
register during S3P1 of the cycle following the one in which
The programmable Watchdog Timer (WDT) operates from
an independent oscillator. The prescaler bits, PS0, PS1
and PS2 in SFR WMCON are used to set the period of the
Watchdog Timer from 16 ms to 2048 ms. The available
timer periods are shown in the following table and the
9
the transition was detected. Since two machine cycles (24
oscillator periods) are required to recognize a 1-to-0 transition, the maximum count rate is 1/24 of the oscillator
frequency. To ensure that a given level is sampled at least
once before it changes, the level should be held for at least
one full machine cycle.
Table 8. Timer 2 Operating Modes
RCLK + TCLK
CP/RL2
TR2
MODE
0
0
1
16-bit Auto-reload
0
1
1
16-bit Capture
1
X
1
Baud Rate Generator
X
X
0
(Off)
Capture Mode
In the capture mode, two options are selected by bit
EXEN2 in T2CON. If EXEN2 = 0, Timer 2 is a 16 bit timer
or counter which upon overflow sets bit TF2 in T2CON.
This bit can then be used to generate an interrupt. If
EXEN2 = 1, Timer 2 performs the same operation, but a lto-0 transition at external input T2EX also causes the current value in TH2 and TL2 to be captured into RCAP2H and
RCAP2L, respectively. In addition, the transition at T2EX
causes bit EXF2 in T2CON to be set. The EXF2 bit, like
TF2, can generate an interrupt. The capture mode is illustrated in Figure 1.
Figure 1. Timer 2 in Capture Mode
÷12
OSC
C/T2 = 0
TH2
TL2
OVERFLOW
CONTROL
C/T2 = 1
TF2
TR2
CAPTURE
T2 PIN
RCAP2H RCAP2L
TRANSITION
DETECTOR
TIMER 2
INTERRUPT
T2EX PIN
EXF2
CONTROL
EXEN2
10
AT89S8252
AT89S8252
Auto-reload (Up or Down Counter)
Timer 2 can be programmed to count up or down when
configured in its 16 bit auto-reload mode. This feature is
invoked by the DCEN (Down Counter Enable) bit located in
the SFR T2MOD (see Table 9). Upon reset, the DCEN bit
is set to 0 so that timer 2 will default to count up. When
DCEN is set, Timer 2 can count up or down, depending on
the value of the T2EX pin.
Figure 2 shows Timer 2 automatically counting up when
DCEN = 0. In this mode, two options are selected by bit
EXEN2 in T2CON. If EXEN2 = 0, Timer 2 counts up to
0FFFFH and then sets the TF2 bit upon overflow. The
overflow also causes the timer registers to be reloaded with
the 16 bit value in RCAP2H and RCAP2L. The values in
RCAP2H and RCAP2L are preset by software. If EXEN2 =
1, a 16 bit reload can be triggered either by an overflow or
by a 1-to-0 transition at external input T2EX. This transition
also sets the EXF2 bit. Both the TF2 and EXF2 bits can
generate an interrupt if enabled.
Setting the DCEN bit enables Timer 2 to count up or down,
as shown in Figure 3. In this mode, the T2EX pin controls
the direction of the count. A logic 1 at T2EX makes Timer 2
count up. The timer will overflow at 0FFFFH and set the
TF2 bit. This overflow also causes the 16 bit value in
RCAP2H and RCAP2L to be reloaded into the timer registers, TH2 and TL2, respectively.
A logic 0 at T2EX makes Timer 2 count down. The timer
underflows when TH2 and TL2 equal the values stored in
RCAP2H and RCAP2L. The underflow sets the TF2 bit and
causes 0FFFFH to be reloaded into the timer registers.
The EXF2 bit toggles whenever Timer 2 overflows or
underflows and can be used as a 17th bit of resolution. In
this operating mode, EXF2 does not flag an interrupt.
Figure 2. Timer 2 in Auto Reload Mode (DCEN = 0)
Table 9. T2MOD – Timer 2 Mode Control Register
T2MOD Address = 0C9H
Reset Value = XXXX XX00B
Not Bit Addressable
Bit
–
–
–
–
–
–
T2OE
DCEN
7
6
5
4
3
2
1
0
Symbol
Function
–
Not implemented, reserved for future use.
T2OE
Timer 2 Output Enable bit.
DCEN
When set, this bit allows Timer 2 to be configured as an up/down counter.
11
Figure 3. Timer 2 Auto Reload Mode (DCEN = 1)
Figure 4. Timer 2 in Baud Rate Generator Mode
TIMER 1 OVERFLOW
÷2
"0"
"1"
NOTE: OSC. FREQ. IS DIVIDED BY 2, NOT 12
SMOD1
OSC
÷2
C/T2 = 0
"1"
TH2
"0"
TL2
RCLK
CONTROL
TR2
÷16
Rx
CLOCK
C/T2 = 1
"1"
"0"
T2 PIN
TCLK
RCAP2H RCAP2L
TRANSITION
DETECTOR
÷ 16
T2EX PIN
EXF2
CONTROL
EXEN2
12
AT89S8252
TIMER 2
INTERRUPT
Tx
CLOCK
AT89S8252
Baud Rate Generator
Timer 2 is selected as the baud rate generator by setting
TCLK and/or RCLK in T2CON (Table 2). Note that the
baud rates for transmit and receive can be different if Timer
2 is used for the receiver or transmitter and Timer 1 is used
for the other function. Setting RCLK and/or TCLK puts
Timer 2 into its baud rate generator mode, as shown in Figure 4.
The baud rate generator mode is similar to the auto-reload
mode, in that a rollover in TH2 causes the Timer 2 registers
to be reloaded with the 16 bit value in registers RCAP2H
and RCAP2L, which are preset by software.
The baud rates in Modes 1 and 3 are determined by Timer
2’s overflow rate according to the following equation.
Timer 2 Overflow Rate
Modes 1 and 3 Baud Rates = -----------------------------------------------------------16
The Timer can be configured for either timer or counter
operation. In most applications, it is configured for timer
operation (CP/T2 = 0). The timer operation is different for
Timer 2 when it is used as a baud rate generator. Normally,
as a timer, it increments every machine cycle (at 1/12 the
oscillator frequency). As a baud rate generator, however, it
increments every state time (at 1/2 the oscillator frequency). The baud rate formula is given below.
2 is in use as a baud rate generator, T2EX can be used as
an extra external interrupt.
Note that when Timer 2 is running (TR2 = 1) as a timer in
the baud rate generator mode, TH2 or TL2 should not be
read from or written to. Under these conditions, the Timer is
incremented every state time, and the results of a read or
write may not be accurate. The RCAP2 registers may be
read but should not be written to, because a write might
overlap a reload and cause write and/or reload errors. The
timer should be turned off (clear TR2) before accessing the
Timer 2 or RCAP2 registers.
Programmable Clock Out
A 50% duty cycle clock can be programmed to come out on
P1.0, as shown in Figure 5. This pin, besides being a regul ar I/0 p i n, h as t wo a lt er n ate fun c ti on s. I t c an b e
programmed to input the external clock for Timer/Counter 2
or to output a 50% duty cycle clock ranging from 61 Hz to 4
MHz at a 16 MHz operating frequency.
To configure the Timer/Counter 2 as a clock generator, bit
C/T2 (T2CON.1) must be cleared and bit T2OE (T2MOD.1)
must be set. Bit TR2 (T2CON.2) starts and stops the timer.
The clock-out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers
(RCAP2H, RCAP2L), as shown in the following equation.
Modes 1 and 3
Oscillator Frequency
--------------------------------------- = ---------------------------------------------------------------------------------------------Baud Rate
32 × [ 65536 – ( RCAP2H,RCAP2L ) ]
Oscillator Frequency
Clock Out Frequency = ------------------------------------------------------------------------------------------4 × [ 65536 – ( RCAP2H,RCAP2L ) ]
where (RCAP2H, RCAP2L) is the content of RCAP2H and
RCAP2L taken as a 16 bit unsigned integer.
In the clock-out mode, Timer 2 rollovers will not generate
an interrupt. This behavior is similar to when Timer 2 is
used as a baud-rate generator. It is possible to use Timer 2
as a baud-rate generator and a clock generator simultaneously. Note, however, that the baud-rate and clock-out
frequencies cannot be determined independently from one
another since they both use RCAP2H and RCAP2L.
Timer 2 as a baud rate generator is shown in Figure 4. This
figure is valid only if RCLK or TCLK = 1 in T2CON. Note
that a rollover in TH2 does not set TF2 and will not generate an interrupt. Note too, that if EXEN2 is set, a 1-to-0
transition in T2EX will set EXF2 but will not cause a reload
from (RCAP2H, RCAP2L) to (TH2, TL2). Thus when Timer
13
Figure 5. Timer 2 in Clock-out Mode
Figure 6. SPI Block Diagram
S
LSB
MSB
S
8/16-BIT SHIFT REGISTER
READ DATA BUFFER
DIVIDER
÷4÷16÷64÷128
CLOCK
SPI CLOCK (MASTER)
MOSI
P1.5
SCK
1.7
M
SPR0
SPI STATUS REGISTER
SPR0
SPR1
CPHA
CPOL
MSTR
SPI CONTROL REGISTER
8
8
SPI INTERRUPT INTERNAL
REQUEST
DATA BUS
AT89S8252
DORD
SPE
8
SPIE
MSTR
SPE
WCOL
SPI CONTROL
DORD
SPE
SS
P1.4
MSTR
SPR1
S
CLOCK
LOGIC
SELECT
SPIF
PIN CONTROL LOGIC
OSCILLATOR
14
MISO
P1.6
M
M
AT89S8252
UART
• Write Collision Flag Protection
• Wakeup from Idle Mode (Slave Mode Only)
The UART in the AT89S8252 operates the same way as
the UART in the AT89C51, AT89C52 and AT89C55. For
further information, see the October 1995 Microcontroller
Data Book, page 2-49, section titled, “Serial Interface.”
The interconnection between master and slave CPUs with
SPI is shown in the following figure. The SCK pin is the
clock output in the master mode but is the clock input in the
slave mode. Writing to the SPI data register of the master
CPU starts the SPI clock generator, and the data written
shifts out of the MOSI pin and into the MOSI pin of the
slave CPU. After shifting one byte, the SPI clock generator
stops, setting the end of transmission flag (SPIF). If both
the SPI interrupt enable bit (SPIE) and the serial port interrupt enable bit (ES) are set, an interrupt is requested.
Serial Peripheral Interface
The serial peripheral interface (SPI) allows high-speed synchronous data transfer between the AT89S8252 and
peripheral devices or between several AT89S8252
devices. The AT89S8252 SPI features include the
following:
• Full-Duplex, 3-Wire Synchronous Data Transfer
The Slave Select input, SS/P1.4, is set low to select an
individual SPI device as a slave. When SS/P1.4 is set high,
the SPI port is deactivated and the MOSI/P1.5 pin can be
used as an input.
• Master or Slave Operation
• 1.5 MHz Bit Frequency (max.)
There are four combinations of SCK phase and polarity
with respect to serial data, which are determined by control
bits CPHA and CPOL. The SPI data transfer formats are
shown in Figure 8 and Figure 9.
• LSB First or MSB First Data Transfer
• Four Programmable Bit Rates
• End of Transmission Interrupt Flag
Figure 7. SPI Master-slave Interconnection
MSB
MASTER
LSB
MISO MISO
8-BIT SHIFT REGISTER
MSB
SLAVE
LSB
8-BIT SHIFT REGISTER
MOSI MOSI
SPI
CLOCK GENERATOR
SCK
SS
SCK
SS
VCC
Figure 8. SPI transfer Format with CPHA = 0
*Not defined but normally MSB of character just received
15
Figure 9. SPI Transfer Format with CPHA = 1
SCK CYCLE #
(FOR REFERENCE)
1
2
3
4
5
6
7
8
SCK (CPOL=0)
SCK (CPOL=1)
MOSI
(FROM MASTER)
MISO
(FROM SLAVE)
*
MSB
6
5
4
3
2
1
MSB
6
5
4
3
2
1
LSB
LSB
SS (TO SLAVE)
*Not defined but normally LSB of previously transmitted character
Interrupts
The AT89S8252 has a total of six interrupt vectors: two
external interrupts (INT0 and INT1), three timer interrupts
(Timers 0, 1, and 2), and the serial port interrupt. These
interrupts are all shown in Figure 10.
Table 10. Interrupt Enable (IE) Register
Each of these interrupt sources can be individually enabled
or disabled by setting or clearing a bit in Special Function
Register IE. IE also contains a global disable bit, EA, which
disables all interrupts at once.
Enable Bit = 1 enables the interrupt.
Note that Table 10 shows that bit position IE.6 is unimplemented. In the A T89 C5 1, bit positi on IE.5 is als o
unimplemented. User software should not write 1s to these
bit positions, since they may be used in future AT89
products.
Timer 2 interrupt is generated by the logical OR of bits TF2
and EXF2 in register T2CON. Neither of these flags is
cleared by hardware when the service routine is vectored
to. In fact, the service routine may have to determine
whether it was TF2 or EXF2 that generated the interrupt,
and that bit will have to be cleared in software.
The Timer 0 and Timer 1 flags, TF0 and TF1, are set at
S5P2 of the cycle in which the timers overflow. The values
are then polled by the circuitry in the next cycle. However,
the Timer 2 flag, TF2, is set at S2P2 and is polled in the
same cycle in which the timer overflows.
16
AT89S8252
(MSB)(LSB)
EA
–
ET2
ES
ET1
EX1
ET0
EX0
Enable Bit = 0 disables the interrupt.
Symbol
Position
Function
EA
IE.7
Disables all interrupts. If EA = 0, no interrupt
is acknowledged. If EA = 1, each interrupt
source is individually enabled or disabled by
setting or clearing its enable bit.
–
IE.6
Reserved.
ET2
IE.5
Timer 2 interrupt enable bit.
ES
IE.4
SPI and UART interrupt enable bit.
ET1
IE.3
Timer 1 interrupt enable bit.
EX1
IE.2
External interrupt 1 enable bit.
ET0
IE.1
Timer 0 interrupt enable bit.
EX0
IE.0
External interrupt 0 enable bit.
User software should never write 1s to unimplemented bits, because
they may be used in future AT89 products.
AT89S8252
Figure 10. Interrupt Sources
Figure 11. Oscillator Connections
Note:
Note: C1, C2 = 30 pF ± 10 pF for Crystals
= 40 pF ± 10 pF for Ceramic Resonators
Figure 12. External Clock Drive Configuration
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively,
of an inverting amplifier that can be configured for use as
an on-chip oscillator, as shown in Figure 11. Either a quartz
crystal or ceramic resonator may be used. To drive the
device from an external clock source, XTAL2 should be left
unconnected while XTAL1 is driven, as shown in Figure 12.
There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry
is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be
observed.
17
Idle Mode
In idle mode, the CPU puts itself to sleep while all the onchip peripherals remain active. The mode is invoked by
software. The content of the on-chip RAM and all the special functions registers remain unchanged during this
mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
Note that when idle mode is terminated by a hardware
reset, the device normally resumes program execution
from where it left off, up to two machine cycles before the
internal reset algorithm takes control. On-chip hardware
inhibits access to internal RAM in this event, but access to
the port pins is not inhibited. To eliminate the possibility of
an unexpected write to a port pin when idle mode is terminated by a reset, the instruction following the one that
invokes idle mode should not write to a port pin or to external memory.
Status of External Pins During Idle and Power-down Modes
Mode
Program Memory
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power-down
Internal
0
0
Data
Data
Data
Data
Power-down
External
0
0
Float
Data
Data
Data
Power-down Mode
Program Memory Lock Bits
In the power-down mode, the oscillator is stopped and the
instruction that invokes power-down is the last instruction
executed. The on-chip RAM and Special Function Registers retain their values until the power-down mode is
terminated. Exit from power-down can be initiated either by
a hardware reset or by an enabled external interrupt. Reset
redefines the SFRs but does not change the on-chip RAM.
The reset should not be activated before VCC is restored to
its normal operating level and must be held active long
enough to allow the oscillator to restart and stabilize.
The AT89S8252 has three lock bits that can be left unprogrammed (U) or can be programmed (P) to obtain the
additional features listed in the following table.
To exit power-down via an interrupt, the external interrupt
must be enabled as level sensitive before entering powerdown. The interrupt service routine starts at 16 ms (nominal) after the enabled interrupt pin is activated.
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is powered up without a reset, the latch initializes to a random
value and holds that value until reset is activated. The
latched value of EA must agree with the current logic level
at that pin in order for the device to function properly.
Once programmed, the lock bits can only be unprogrammed with the Chip Erase operations in either the
parallel or serial modes.
Lock Bit Protection Modes(1)(2)
Program Lock Bits
LB1
LB2
LB3
1
U
U
U
No internal memory lock feature.
2
P
U
U
MOVC instructions executed from external program memory are disabled from fetching code bytes
from internal memory. EA is sampled and latched on reset and further programming of the Flash
memory (parallel or serial mode) is disabled.
3
P
P
U
Same as Mode 2, but parallel or serial verify are also disabled.
4
Notes:
18
Protection Type
P
P
P
Same as Mode 3, but external execution is also disabled.
1. U = Unprogrammed
2. P = Programmed
AT89S8252
AT89S8252
Programming the Flash and EEPROM
Atmel’s AT89S8252 Flash Microcontroller offers 8K bytes
of in-system reprogrammable Flash Code memory and 2K
bytes of EEPROM Data memory.
The AT89S8252 is normally shipped with the on-chip Flash
Code and EEPROM Data memory arrays in the erased
state (i.e. contents = FFH) and ready to be programmed.
This device supports a High-voltage (12V) Parallel programming mode and a Low-voltage (5V) Serial
programming mode. The serial programming mode provides a convenient way to download the AT89S8252 inside
the user’s system. The parallel programming mode is compatible with conventional third party Flash or EPROM
programmers.
The Code and Data memory arrays are mapped via separate address spaces in the serial programming mode. In
the parallel programming mode, the two arrays occupy one
contiguous address space: 0000H to 1FFFH for the Code
array and 2000H to 27FFH for the Data array.
The Code and Data memory arrays on the AT89S8252 are
programmed byte-by-byte in either programming mode. An
auto-erase cycle is provided with the self-timed programming operation in the serial programming mode. There is
no need to perform the Chip Erase operation to reprogram
any memory location in the serial programming mode
unless any of the lock bits have been programmed.
In the parallel programming mode, there is no auto-erase
cycle. To reprogram any non-blank byte, the user needs to
use the Chip Erase operation first to erase both arrays.
Parallel Programming Algorithm: To program and verify
the AT89S8252 in the parallel programming mode, the following sequence is recommended:
1. Power-up sequence:
Apply power between VCC and GND pins.
Set RST pin to “H”.
Apply a 3 MHz to 24 MHz clock to XTAL1 pin and wait
for at least 10 milliseconds.
2. Set PSEN pin to “L”
ALE pin to “H”
EA pin to “H” and all other pins to “H”.
3. Apply the appropriate combination of “H” or “L” logic
levels to pins P2.6, P2.7, P3.6, P3.7 to select one of
the programming operations shown in the Flash
Programming Modes table.
4. Apply the desired byte address to pins P1.0 to P1.7
and P2.0 to P2.5.
Apply data to pins P0.0 to P0.7 for Write Code
operation.
5. Raise EA/VPP to 12V to enable Flash programming,
erase or verification.
6. Pulse ALE/PROG once to program a byte in the
Code memory array, the Data memory array or the
lock bits. The byte-write cycle is self-timed and typically takes 1.5 ms.
7. To verify the byte just programmed, bring pin P2.7 to
“L” and read the programmed data at pins P0.0 to
P0.7.
8. Repeat steps 3 through 7 changing the address and
data for the entire 2K or 8K bytes array or until the
end of the object file is reached.
9. Power-off sequence:
Set XTAL1 to “L”.
Set RST and EA pins to “L”.
Turn VCC power off.
In the parallel programming mode, there is no auto-erase
cycle and to reprogram any non-blank byte, the user needs
to use the Chip Erase operation first to erase both arrays.
Data Polling: The AT89S8252 features DATA Polling to
indicate the end of a write cycle. During a write cycle in the
parallel or serial programming mode, an attempted read of
the last byte written will result in the complement of the written datum on P0.7 (parallel mode), and on the MSB of the
serial output byte on MISO (serial mode). Once the write
cycle has been completed, true data are valid on all outputs, and the next cycle may begin. DATA Polling may
begin any time after a write cycle has been initiated.
Ready/Busy: The progress of byte programming in the
parallel programming mode can also be monitored by the
RDY/BSY output signal. Pin P3.4 is pulled Low after ALE
goes High during programming to indicate BUSY. P3.4 is
pulled High again when programming is done to indicate
READY.
Program Verify: If lock bits LB1 and LB2 have not been
programmed, the programmed Code or Data byte can be
read back via the address and data lines for verification.
The state of the lock bits can also be verified directly in the
parallel programming mode. In the serial programming
mode, the state of the lock bits can only be verified indirectly by observing that the lock bit features are enabled.
Chip Erase: Both Flash and EEPROM arrays are erased
electrically at the same time. In the parallel programming
mode, chip erase is initiated by using the proper combination of control signals and by holding ALE/PROG low for 10
ms. The Code and Data arrays are written with all “1”s in
the Chip Erase operation.
19
In the serial programming mode, a chip erase operation is
initiated by issuing the Chip Erase instruction. In this mode,
chip erase is self-timed and takes about 16 ms.
During chip erase, a serial read from any address location
will return 00H at the data outputs.
Serial Programming Fuse: A programmable fuse is available to disable Serial Programming if the user needs
maximum system security. The Serial Programming Fuse
can only be programmed or erased in the Parallel Programming Mode.
The AT89S8252 is shipped with the Serial Programming
Mode enabled.
Reading the Signature Bytes: The signature bytes are
read by the same procedure as a normal verification of
locations 030H and 031H, except that P3.6 and P3.7 must
be pulled to a logic low. The values returned are as follows:
(030H) = 1EH indicates manufactured by Atmel
(031H) = 72H indicates 89S8252
Programming Interface
Every code byte in the Flash and EEPROM arrays can be
written, and the entire array can be erased, by using the
appropriate combination of control signals. The write operation cycle is self-timed and once initiated, will
automatically time itself to completion.
0000H to 1FFFH for Code memory and 000H to 7FFH for
Data memory.
Either an external system clock is supplied at pin XTAL1 or
a crystal needs to be connected across pins XTAL1 and
XTAL2. The maximum serial clock (SCK) frequency should
be less than 1/40 of the crystal frequency. With a 24 MHz
oscillator clock, the maximum SCK frequency is 600 kHz.
Serial Programming Algorithm
To program and verify the AT89S8252 in the serial programming mode, the following sequence is recommended:
1. Power-up sequence:
Apply power between VCC and GND pins.
Set RST pin to “H”.
If a crystal is not connected across pins XTAL1 and
XTAL2, apply a 3 MHz to 24 MHz clock to XTAL1 pin
and wait for at least 10 milliseconds.
2. Enable serial programming by sending the Programming Enable serial instruction to pin
MOSI/P1.5. The frequency of the shift clock supplied at pin SCK/P1.7 needs to be less than the
CPU clock at XTAL1 divided by 40.
All major programming vendors offer worldwide support for
the Atmel microcontroller series. Please contact your local
programming vendor for the appropriate software revision.
3. The Code or Data array is programmed one byte at
a time by supplying the address and data together
with the appropriate Write instruction. The selected
memory location is first automatically erased before
new data is written. The write cycle is self-timed and
typically takes less than 2.5 ms at 5V.
Serial Downloading
4. Any memory location can be verified by using the
Read instruction which returns the content at the
selected address at serial output MISO/P1.6.
Both the Code and Data memory arrays can be programmed using the serial SPI bus while RST is pulled to
VCC. The serial interface consists of pins SCK, MOSI (input)
and MISO (output). After RST is set high, the Programming
Enable instruction needs to be executed first before program/erase operations can be executed.
An auto-erase cycle is built into the self-timed programming
operation (in the serial mode ONLY) and there is no need
to first execute the Chip Erase instruction unless any of the
lock bits have been programmed. The Chip Erase operation turns the content of every memory location in both the
Code and Data arrays into FFH.
The Code and Data memory arrays have separate address
spaces:
20
AT89S8252
5. At the end of a programming session, RST can be
set low to commence normal operation.
Power-off sequence (if needed):
Set XTAL1 to “L” (if a crystal is not used).
Set RST to “L”.
Turn VCC power off.
Serial Programming Instruction
The Instruction Set for Serial Programming follows a 3-byte
protocol and is shown in the following table:
AT89S8252
Instruction Set
Input Format
Instruction
Byte 1
Byte 2
Byte 3
Programming Enable
1010 1100
0101 0011
xxxx xxxx
Enable serial programming interface after RST goes high.
Chip Erase
1010 1100
xxxx x100
xxxx xxxx
Chip erase both 8K & 2K memory arrays.
Read Code Memory
aaaa a001
low addr
xxxx xxxx
Read data from Code memory array at the selected address.
The 5 MSBs of the first byte are the high order address bits.
The low order address bits are in the second byte. Data are
available at pin MISO during the third byte.
Write Code Memory
aaaa a010
low addr
data in
Write data to Code memory location at selected address. The
address bits are the 5 MSBs of the first byte together with the
second byte.
Read Data Memory
00aa a101
low addr
xxxx xxxx
Read data from Data memory array at selected address. Data
are available at pin MISO during the third byte.
Write Data Memory
00aa a110
low addr
data in
Write Lock Bits
1010 1100
Note:
x x111
Operation
Write data to Data memory location at selected address.
xxxx xxxx
Write lock bits.
Set LB1, LB2 or LB3 = “0” to program lock bits.
1. DATA polling is used to indicate the end of a write cycle which typically takes less than 2.5 ms at 5V.
2. “aaaaa” = high order address.
3. “x” = don’t care.
21
Flash and EEPROM Parallel Programming Modes
P2.6
P2.7
P3.6
P3.7
Data I/O
P0.7:0
Address
P2.5:0 P1.7:0
12V
H
L
L
L
X
X
12V
L
H
H
H
DIN
ADDR
12V
L
L
H
H
DOUT
ADDR
12V
H
L
H
L
DIN
X
Bit - 1
P0.7 = 0
X
Bit - 2
P0.6 = 0
X
Bit - 3
P0.5 = 0
X
DOUT
X
Bit - 1
@P0.2
X
Bit - 2
@P0.1
X
Bit - 3
@P0.0
X
Mode
RST
PSEN
ALE/PROG
EA/VPP
Serial Prog. Modes
H
h(1)
h(1)
x
Chip Erase
H
L
Write (10K bytes) Memory
H
L
Read (10K bytes) Memory
H
L
Write Lock Bits:
H
L
Read Lock Bits:
H
L
(2)
H
H
12V
H
H
L
L
Read Atmel Code
H
L
H
12V
L
L
L
L
DOUT
30H
Read Device Code
H
L
H
12V
L
L
L
L
DOUT
31H
Serial Prog. Enable
H
L
(2)
12V
L
H
L
H
P0.0 = 0
X
Serial Prog. Disable
H
L
(2)
12V
L
H
L
H
P0.0 = 1
X
Read Serial Prog. Fuse
H
L
H
H
L
H
@P0.0
X
Notes:
22
H
1. “h” = weakly pulled “High” internally.
2. Chip Erase and Serial Programming Fuse require a
10 ms PROG pulse. Chip Erase needs to be performed first before reprogramming any byte with a
content other than FFH.
AT89S8252
12V
3. P3.4 is pulled Low during programming to indicate
RDY/BSY.
4. “X” = don’t care
AT89S8252
Figure 13. Programming the Flash/EEPROM Memory
Figure 15. Flash/EEPROM Serial Downloading
+4.0V to 6.0V
+5V
AT89S8252
A0 - A7
ADDR.
0000H/27FFH
AT89S8252
VCC
VCC
P1
P2.0 - P2.5
PGM
DATA
P0
A8 - A13
P2.6
SEE FLASH
PROGRAMMING
MODES TABLE
P2.7
ALE
PROG
P3.6
INSTRUCTION
INPUT
P1.5/MOSI
DATA OUTPUT
P1.6/MISO
CLOCK IN
P1.7/SCK
P3.7
XTAL2
EA
XTAL2
VPP
3-24 MHz
3-24 MHz
XTAL1
GND
VIH
RST
XTAL1
RST
VIH
GND
PSEN
Figure 14. Verifying the Flash/EEPROM Memory
+5V
AT89S8252
ADDR.
0000H/2FFFH
A0 - A7
A8 - A13
SEE FLASH
PROGRAMMING
MODES TABLE
P1
VCC
P2.0 - P2.5
P0
P2.6
P2.7
PGM DATA
(USE 10K
PULLUPS)
ALE
VI H
XTAL2
EA
VPP
XTAL1
RST
VI H
P3.6
P3.7
3-24 Mhz
GND
PSEN
23
Flash Programming and Verification Characteristics – Parallel Mode
TA = 0°C to 70°C, VCC = 5.0V ± 10%
Symbol
Parameter
Min
Max
Units
VPP
Programming Enable Voltage
11.5
12.5
V
IPP
Programming Enable Current
1.0
mA
1/tCLCL
Oscillator Frequency
24
MHz
tAVGL
Address Setup to PROG Low
48tCLCL
tGHAX
Address Hold after PROG
48tCLCL
tDVGL
Data Setup to PROG Low
48tCLCL
tGHDX
Data Hold after PROG
48tCLCL
tEHSH
P2.7 (ENABLE) High to VPP
48tCLCL
tSHGL
VPP Setup to PROG Low
10
tGLGH
PROG Width
1
tAVQV
Address to Data Valid
48tCLCL
tELQV
ENABLE Low to Data Valid
48tCLCL
tEHQZ
Data Float after ENABLE
tGHBL
PROG High to BUSY Low
1.0
µs
tWC
Byte Write Cycle Time
2.0
ms
24
AT89S8252
3
0
µs
110
µs
48tCLCL
AT89S8252
Flash/EEPROM Programming and Verification Waveforms – Parallel Mode
Serial Downloading Waveforms
SERIAL CLOCK INPUT
SCK/P1.7
7
6
5
4
3
2
1
0
SERIAL DATA INPUT
MOSI/P1.5
MSB
LSB
MSB
LSB
SERIAL DATA OUTPUT
MISO/P1.6
25
Z
Absolute Maximum Ratings*
Operating Temperature.................................. -55°C to +125°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin
with Respect to Ground .....................................-1.0V to +7.0V
Maximum Operating Voltage ............................................ 6.6V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
DC Output Current...................................................... 15.0 mA
DC Characteristics
The values shown in this table are valid for TA = -40°C to 85°C and VCC = 5.0V ± 20%, unless otherwise noted.
Symbol
Parameter
Condition
Min
Max
Units
VIL
Input Low-voltage
(Except EA)
-0.5
0.2 VCC - 0.1
V
VIL1
Input Low-voltage (EA)
-0.5
0.2 VCC - 0.3
V
VIH
Input Hifh-voltage
0.2 VCC + 0.9
VCC + 0.5
V
VIH1
Input Hifh-voltage
0.7 VCC
VCC + 0.5
V
IOL = 1.6 mA
0.5
V
IOL = 3.2 mA
0.5
V
(Except XTAL1, RST)
(XTAL1, RST)
(1)
VOL
Output Low-voltage
(Ports 1,2,3)
VOL1
Output Low-voltage (1)
(Port 0, ALE, PSEN)
VOH
Output Hifh-voltage
(Ports 1,2,3, ALE, PSEN)
IOH = -60 µA, VCC = 5V ± 10%
2.4
V
IOH = -25 µA
0.75 VCC
V
IOH = -10 µA
0.9 VCC
V
2.4
V
IOH = -300 µA
0.75 VCC
V
IOH = -80 µA
0.9 VCC
V
IOH = -800 µA, VCC = 5V ± 10%
VOH1
Output Hifh-voltage
(Port 0 in External Bus Mode)
IIL
Logical 0 Input Current (Ports 1,2,3)
VIN = 0.45V
-50
µA
ITL
Logical 1 to 0 Transition Current (Ports 1,2,3)
VIN = 2V, VCC = 5V ± 10%
-650
µA
ILI
Input Leakage Current
(Port 0, EA)
0.45 < VIN < VCC
±10
µA
RRST
Reset Pull-down Resistor
300
KΩ
CIO
Pin Capacitance
Test Freq. = 1 MHz, TA = 25°C
10
pF
Active Mode, 12 MHz
25
mA
Idle Mode, 12 MHz
6.5
mA
VCC = 6V
100
µA
50
Power Supply Current
ICC
Power-down Mode (2)
VCC = 3V
Notes:
26
1. Under steady state (non-transient) conditions, IOL
must be externally limited as follows:
Maximum IOL per port pin: 10 mA
Maximum IOL per 8-bit port:
Port 0: 26 mA
Ports 1, 2, 3: 15 mA
AT89S8252
40
µA
Maximum total IOL for all output pins: 71 mA
If IOL exceeds the test condition, VOL may exceed the
related specification. Pins are not guaranteed to sink
current greater than the listed test conditions.
2. Minimum VCC for Power-down is 2V
AT89S8252
AC Characteristics
Under operating conditions, load capacitance for Port 0, ALE/PROG, and PSEN = 100 pF; load capacitance for all other
outputs = 80 pF.
External Program and Data Memory Characteristics
Variable Oscillator
Symbol
Parameter
Min
Max
Units
1/tCLCL
Oscillator Frequency
0
24
MHz
tLHLL
ALE Pulse Width
2tCLCL - 40
ns
tAVLL
Address Valid to ALE Low
tCLCL - 13
ns
tLLAX
Address Hold after ALE Low
tCLCL - 20
ns
tLLIV
ALE Low to Valid Instruction In
tLLPL
ALE Low to PSEN Low
tCLCL - 13
ns
tPLPH
PSEN Pulse Width
3tCLCL - 20
ns
tPLIV
PSEN Low to Valid Instruction In
tPXIX
Input Instruction Hold after PSEN
tPXIZ
Input Instruction Float after PSEN
tPXAV
PSEN to Address Valid
tAVIV
Address to Valid Instruction In
tPLAZ
PSEN Low to Address Float
tRLRH
RD Pulse Width
6tCLCL - 100
ns
tWLWH
WR Pulse Width
6tCLCL - 100
ns
tRLDV
RD Low to Valid Data In
tRHDX
Data Hold after RD
tRHDZ
Data Float after RD
2tCLCL - 28
ns
tLLDV
ALE Low to Valid Data In
8tCLCL - 150
ns
tAVDV
Address to Valid Data In
9tCLCL - 165
ns
tLLWL
ALE Low to RD or WR Low
3tCLCL - 50
3tCLCL + 50
ns
tAVWL
Address to RD or WR Low
4tCLCL - 75
ns
tQVWX
Data Valid to WR Transition
tCLCL - 20
ns
tQVWH
Data Valid to WR High
7tCLCL - 120
ns
tWHQX
Data Hold after WR
tCLCL - 20
ns
tRLAZ
RD Low to Address Float
tWHLH
RD or WR High to ALE High
4tCLCL - 65
3tCLCL - 45
0
ns
ns
tCLCL - 10
tCLCL - 8
ns
ns
5tCLCL - 55
ns
10
ns
5tCLCL - 90
0
tCLCL - 20
ns
ns
ns
0
ns
tCLCL + 25
ns
27
External Program Memory Read Cycle
External Data Memory Read Cycle
28
AT89S8252
AT89S8252
External Data Memory Write Cycle
External Clock Drive Waveforms
External Clock Drive
Symbol
Parameter
1/tCLCL
Oscillator Frequency
tCLCL
Clock Period
tCHCX
VCC = 4.0V to 6.0V
Units
Min
Max
0
24
MHz
41.6
ns
High Time
15
ns
tCLCX
Low Time
15
ns
tCLCH
Rise Time
20
ns
tCHCL
Fall Time
20
ns
29
Serial Port Timing: Shift Register Mode Test Conditions
The values in this table are valid for VCC = 4.0V to 6V and Load Capacitance = 80 pF.
Symbol
Parameter
Variable Oscillator
Min
tXLXL
Serial Port Clock Cycle Time
tQVXH
Output Data Setup to Clock Rising Edge
tXHQX
Output Data Hold after Clock Rising Edge
tXHDX
Input Data Hold after Clock Rising Edge
tXHDV
Clock Rising Edge to Input Data Valid
Units
Max
12tCLCL
µs
10tCLCL - 133
ns
2tCLCL - 117
ns
0
ns
10tCLCL - 133
ns
Shift Register Mode Timing Waveforms
AC Testing Input/Output Waveforms(1)
Float Waveforms(1)
Notes:
Notes:
30
1. AC Inputs during testing are driven at VCC - 0.5V
for a logic 1 and 0.45V for a logic 0. Timing measurements are made at VIH min. for a logic 1 and VIL max.
for a logic 0.
AT89S8252
1. For timing purposes, a port pin is no longer floating
when a 100 mV change from load voltage occurs. A
port pin begins to float when a 100 mV change from
the loaded VOH/VOL level occurs.
AT89S8252
AT89S8252
TYPICAL ICC (ACTIVE) at 25°C
24
VCC = 6.0V
20
I
C 16
C
12
m
A 8
VCC = 5.0V
4
0
0
4
8
12
16
20
24
F (MHz)
AT89S8252
TYPICAL ICC (IDLE) at 25°C
4.8
VCC = 6.0V
4.0
I
C 3.2
C 2.4
VCC = 5.0V
m 1.6
A
0.8
0.0
0
4
8
12
16
20
24
F (MHz)
Notes:
1. XTAL1 tied to GND for Icc (power-down)
2. Lock bits programmed
31
Ordering Information
Speed
(MHz)
Power
Supply
24
33
Ordering Code
Package
Operation Range
4.0V to 6.0V
AT89S8252-24AC
AT89S8252-24JC
AT89S8252-24PC
AT89S8252-24QC
44A
44J
40P6
44Q
Commercial
(0°C to 70°C)
4.0V to 6.0V
AT89S8252-24AI
AT89S8252-24JI
AT89S8252-24PI
AT89S8252-24QI
44A
44J
40P6
44Q
Industrial
(-40°C to 85°C)
4.5V to 5.5V
AT89S8252-33AC
AT89S8252-33JC
AT89S8252-33PC
AT89S8252-33QC
44A
44J
40P6
44Q
Commercial
(0°C to 70°C)
= Preliminary Information
Package Type
44A
44-lead, Thin Plastic Gull Wing Quad Flatpack (TQFP)
44J
44-lead, Plastic J-leaded Chip Carrier (PLCC)
40P6
40-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP)
44Q
44-lead, Plastic Gull Wing Quad Flatpack (PQFP)
32
AT89S8252
AT89S8252
Packaging Information
44A, 44-lead, Thin (1.0 mm) Plastic Gull Wing Quad
Flatpack (TQFP)
Dimensions in Millimeters and (Inches)*
44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC)
Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-018 AC
JEDEC STANDARD MS-026 ACB
12.21(0.478)
SQ
11.75(0.458)
PIN 1 ID
0.45(0.018)
0.30(0.012)
0.80(0.031) BSC
.045(1.14) X 45°
.045(1.14) X 30° - 45°
PIN NO. 1
IDENTIFY
.630(16.0)
.590(15.0)
.656(16.7)
SQ
.650(16.5)
.032(.813)
.026(.660)
.695(17.7)
SQ
.685(17.4)
.050(1.27) TYP
.500(12.7) REF SQ
10.10(0.394)
SQ
9.90(0.386)
.021(.533)
.013(.330)
.043(1.09)
.020(.508)
.120(3.05)
.090(2.29)
.180(4.57)
.165(4.19)
1.20(0.047) MAX
0
7
0.20(.008)
0.09(.003)
.012(.305)
.008(.203)
.022(.559) X 45° MAX (3X)
0.75(0.030)
0.45(0.018)
0.15(0.006)
0.05(0.002)
Controlling dimension: millimeters
40P6, 40-lead, 0.600" Wide, Plastic Dual Inline
Package (PDIP)
Dimensions in Inches and (Millimeters)
2.07(52.6)
2.04(51.8)
44Q, 44-lead, Plastic Quad Flat Package (PQFP)
Dimensions in Millimeters and (Inches)*
JEDEC STANDARD MS-022 AB
13.45 (0.525)
SQ
12.95 (0.506)
PIN
1
PIN 1 ID
.566(14.4)
.530(13.5)
0.50 (0.020)
0.35 (0.014)
0.80 (0.031) BSC
.090(2.29)
MAX
1.900(48.26) REF
.220(5.59)
MAX
.005(.127)
MIN
SEATING
PLANE
.065(1.65)
.015(.381)
.022(.559)
.014(.356)
.161(4.09)
.125(3.18)
.110(2.79)
.090(2.29)
.012(.305)
.008(.203)
.065(1.65)
.041(1.04)
10.10 (0.394)
SQ
9.90 (0.386)
.630(16.0)
.590(15.0)
2.45 (0.096) MAX
0 REF
15
.690(17.5)
.610(15.5)
0.17 (0.007)
0.13 (0.005)
0
7
1.03 (0.041)
0.78 (0.030)
0.25 (0.010) MAX
Controlling dimension: millimeters
33
Atmel Headquarters
Atmel Operations
Corporate Headquarters
Atmel Colorado Springs
2325 Orchard Parkway
San Jose, CA 95131
TEL (408) 441-0311
FAX (408) 487-2600
Europe
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL (719) 576-3300
FAX (719) 540-1759
Atmel Rousset
Atmel U.K., Ltd.
Coliseum Business Centre
Riverside Way
Camberley, Surrey GU15 3YL
England
TEL (44) 1276-686-677
FAX (44) 1276-686-697
Zone Industrielle
13106 Rousset Cedex
France
TEL (33) 4-4253-6000
FAX (33) 4-4253-6001
Asia
Atmel Asia, Ltd.
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
Japan
Atmel Japan K.K.
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
Fax-on-Demand
North America:
1-(800) 292-8635
International:
1-(408) 441-0732
e-mail
[email protected]
Web Site
http://www.atmel.com
BBS
1-(408) 436-4309
© Atmel Corporation 2000.
Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for
any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without
notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are
not authorized for use as critical components in life suppor t devices or systems.
Marks bearing
®
and/or
™
are registered trademarks and trademarks of Atmel Corporation.
Terms and product names in this document may be trademarks of others.
Printed on recycled paper.
0401E–02/00/xM
Similar pages