TI1 LP2981AIM5-5.0 Micropower 100-ma ultralow dropout regulator Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
LP2981-N Micropower 100-mA Ultralow Dropout Regulator in SOT-23 Package
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
•
•
The LP2981-N is a 100-mA, fixed-output voltage
regulator designed specifically to meet the
requirements of battery-powered applications.
1
Operating Input Voltage Range: 2.1 V to 16 V
Ultralow-Dropout Voltage
Output Voltage Accuracy 0.75% (A Grade)
Specified 100-mA Output Current
< 1-μA Quiescent Current when Shutdown
Low Ground Pin Current at All Load Currents
High Peak Current Capability (300 mA Typical)
Wide Supply Voltage Range (16 V Maximum)
Fast Dynamic Response to Line and Load
Low ZOUT Over Wide Frequency Range
Overtemperature and Overcurrent Protection
−40°C to 125°C Junction Temperature Range
Dropout Voltage: Typically 200 mV at 100-mA load,
and 7 mV at 1-mA load.
Ground Pin Current: Typically 600 μA at 100-mA
load, and 80 μA at 1-mA load.
Sleep Mode: Less than 1-μA quiescent current when
ON/OFF pin is pulled low.
Precision Output: 0.75% tolerance output voltages
available (A grade).
2 Applications
•
•
•
•
Using an optimized Vertically Integrated PNP (VIP)
process,
the
LP2981-N
delivers
unequaled
performance in all specifications critical to batterypowered designs:
Cellular Phones
Palmtop and Laptop Computers
Personal Digital Assistants (PDA)
Camcorders, Personal Stereos, Cameras
Assorted voltage options, from 2.5 V to 5 V, are
available as standard products.
Device Information(1)
PART NUMBER
LP2981-N
PACKAGE
BODY SIZE (NOM)
SOT-23 (5)
2.90 mm × 1.60 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application
VIN
IN
VOUT
OUT
COUT
CIN
GND
ON/OFF
ON/OFF
NC
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
5
5
8
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 14
7.1 Overview ................................................................. 14
7.2 Functional Block Diagram ....................................... 14
7.3 Feature Description................................................. 14
7.4 Device Functional Modes........................................ 15
8
Application and Implementation ........................ 16
8.1 Application Information............................................ 16
8.2 Typical Application ................................................. 16
9 Power Supply Recommendations...................... 20
10 Layout................................................................... 20
10.1 Layout Guidelines ................................................. 20
10.2 Layout Example .................................................... 20
11 Device and Documentation Support ................. 21
11.1
11.2
11.3
11.4
11.5
Third-Party Products Disclaimer ...........................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
21
21
21
21
21
12 Mechanical, Packaging, and Orderable
Information ........................................................... 21
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision M (September 2015) to Revision N
•
Page
Changed update typical application drawing and change pin names from Vin, Vout to IN and OUT ................................... 1
Changes from Revision L (June 2015) to Revision M
Page
•
Changed split out ESD values by specific pins ..................................................................................................................... 4
•
Changed correct junction-to-case and junction-to-board values (typo from last format update) .......................................... 5
Changes from Revision K (April 2013) to Revision L
Page
•
Changed "Nine" to "Assorted" ................................................................................................................................................ 1
•
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
•
Changed text of NC pin description ....................................................................................................................................... 3
•
Changed thermal value in footnote 3 .................................................................................................................................... 4
•
Changed thermal values to TI measure ................................................................................................................................ 5
Changes from Revision J (January 2009) to Revision K
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 19
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
5 Pin Configuration and Functions
DBV Package
5-Pin SOT-23
Top View
Pin Functions
PIN
NO.
1
NAME
TYPE
IN
I
2
GND
—
3
ON/OFF
I
DESCRIPTION
Input voltage pin
Common ground (device substrate)
Logic high enable input
4
NC
—
DO NOT CONNECT. Device pin 4 is reserved for post packaging test and calibration of the
LP2989 VOUT accuracy. Device pin 2 must be left floating. Do not connect to any potential. Do
not connect to ground. Any attempt to do pin continuity testing on device pin 2 is discouraged.
Continuity test results will be variable depending on the actions of the factory calibration.
Aggressive pin continuity testing (high voltage, or high current) on device pin 2 may activate the
trim circuitry forcing VOUT to move out of tolerance.
5
OUT
O
Regulated output voltage
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
3
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
Operating junction temperature
Power dissipation
(3)
MIN
MAX
UNIT
−40
125
°C
Internally limited
Input supply voltage (survival)
−0.3
16
V
Input supply voltage (operating)
2.1
16
V
Shutdown input voltage (survival)
−0.3
16
V
Output voltage (survival) (4)
−0.3
9
V
IOUT (survival)
Short-circuit protected
Input-output voltage (survival) (5)
−0.3
16
V
Storage temperature
–65
150
°C
(1)
(2)
(3)
(4)
(5)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace-specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, RθJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using P(MAX) = (TJ(MAX) – TA) / RθJA. The value of RθJA for the SOT-23 package is 175.7°C/W. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown.
If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2980-N output must be diode-clamped
to ground.
The output PNP structure contains a diode between the IN and OUT pins that is normally reverse-biased. Reversing the polarity from
VIN to VOUT will turn on this diode (See Reverse Current Path).
6.2 ESD Ratings
VALUE
V(ESD)
(1)
Electrostatic
discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
Pins 1, 2 and 5
±2000
Pins 3 and 4
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
Operating junction temperature
−40
125
°C
Input supply voltage (operating)
2.1
16
V
4
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
6.4 Thermal Information
LP2981-N
THERMAL METRIC (1)
DBV (SOT-23)
UNIT
5 PINS
RθJA
Junction-to-ambient thermal resistance, High-K
175.7
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
78.0
°C/W
RθJB
Junction-to-board thermal resistance
30.8
°C/W
ψJT
Junction-to-top characterization parameter
2.8
°C/W
ψJB
Junction-to-board characterization parameter
30.3
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics
Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2 V. (1)
PARAMETER
TEST CONDITIONS
ΔVO
ΔVO/ΔVIN
Output voltage line
regulation
MIN
TYP
−1.25
1.25
−2
2
1 mA < IL < 100 mA
–40°C ≤ TJ ≤ 125°C
−2.5
2.5
−3.5
3.5
VO(NOM) + 1 V ≤ VIN ≤ 16 V
0.007
VO(NOM) + 1 V ≤ VIN ≤ 16 V
–40°C ≤ TJ ≤ 125°C
1
7
10
70
100
IL = 1 mA, –40°C ≤ TJ ≤ 125°C
3
7
10
70
100
250
15
IL = 0 mA, –40°C ≤ TJ ≤ 125°C
95
80
IL = 1 mA, –40°C ≤ TJ ≤ 125°C
110
200
IL = 25 mA, –40°C ≤ TJ ≤ 125°C
300
80
600
IL = 100 mA, –40°C ≤ TJ ≤ 125°C
800
110
170
200
550
IL = 100 mA
95
125
170
IL = 25 mA
250
375
65
125
IL = 1 mA
mV
150
200
375
65
%/V
5
150
200
0.014
1
15
IL = 25 mA
IL = 0 mA
(3)
3
%VNOM
0.032
5
IL = 100 mA, –40°C ≤ TJ ≤ 125°C
(2)
0.007
0.032
IL = 100 mA
(1)
0.014
UNIT
MAX
1
IL = 25 mA, –40°C ≤ TJ ≤ 125°C
Ground pin current
TYP
0.75
IL = 1 mA
IGND
MIN
−1
IL = 0 mA, –40°C ≤ TJ ≤ 125°C
Dropout voltage (3)
MAX
−0.75
IL = 0 mA
VIN – VO
LP2981I-XX (2)
1 mA < IL < 100 mA
IL = 1 mA
Output voltage
tolerance
LP2981AI-XX (2)
300
550
600
1500
μA
800
1500
VON/OFF < 0.3 V
0.01
0.8
0.01
0.8
VON/OFF < 0.15 V
–40°C ≤ TJ ≤ 125°C
0.05
2
0.05
2
Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (TJ) range of
–40°C to 125°C, unless otherwise stated. Typical values represent the most likely parametric norm at TA = 25°C, and are provided for
reference purposes only.
Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical
Quality Control (SQC) methods. The limits are used to calculate Average Outgoing Quality Level (AOQL).
Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a
1-V differential.
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
5
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
Electrical Characteristics (continued)
Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2 V.(1)
PARAMETER
TEST CONDITIONS
LP2981AI-XX (2)
MIN
TYP
High = O/P ON
VON/OFF
ON/OFF input
voltage (4)
(4)
6
Peak output current
1.6
Low = O/P OFF
0.5
0.5
0.01
0.01
5
–1
400
μA
5
15
150
UNIT
0.15
–1
VON/OFF = 5 V
MAX
V
0.15
VON/OFF = 0 V
–40°C ≤ TJ ≤ 125°C
VOUT ≥ VO(NOM) − 5%
TYP
1.4
1.6
VON/OFF = 5 V
–40°C ≤ TJ ≤ 125°C
IO(PK)
MIN
1.4
VON/OFF = 0 V
ON/OFF input current
MAX
High = O/P ON
–40°C ≤ TJ ≤ 125°C
Low = O/P OFF
–40°C ≤ TJ ≤ 125°C
ION/OFF
LP2981I-XX (2)
15
150
mA
The ON/OFF inputs must be properly driven to prevent misoperation. For details, see Operation With ON/OFF Control.
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
Electrical Characteristics (continued)
Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2 V.(1)
PARAMETER
en
Output noise voltage
(RMS)
ΔVO/ΔVIN Ripple rejection
IO(MAX)
(5)
Short-circuit current
TEST CONDITIONS
LP2981AI-XX (2)
MIN
TYP
LP2981I-XX (2)
MAX
MIN
TYP
MAX
UNIT
BW = 300 Hz to 50 kHz
COUT = 10 μF
160
160
μV
ƒ = 1 kHz, COUT = 10 μF
63
63
dB
150
150
mA
RL = 0 Ω (steady state)
(5)
See related curve(s) in Typical Characteristics section.
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
7
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
6.6 Typical Characteristics
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 4.7 μF, CIN = 1 μF all voltage options, ON/OFF pin tied to
VIN.
Figure 1. 5-V Output Voltage vs Temperature
Figure 2. 3.3-V Output Voltage vs Temperature
Figure 3. 3-V Output Voltage vs Temperature
Figure 4. 5-V Dropout Characteristics
Figure 5. 3.3-V Dropout Characteristics
8
Submit Documentation Feedback
Figure 6. 3-V Dropout Characteristics
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
Typical Characteristics (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 4.7 μF, CIN = 1 μF all voltage options, ON/OFF pin tied to
VIN.
Figure 7. Dropout Voltage vs Temperature
Figure 8. Dropout Voltage vs Load Current
Figure 9. Ground Pin Current vs Temperature
Figure 10. Ground Pin Current vs Load Current
Figure 11. Input Current vs VIN
Figure 12. Input Current vs VIN
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
9
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 4.7 μF, CIN = 1 μF all voltage options, ON/OFF pin tied to
VIN.
10
Figure 13. Line Transient Response
Figure 14. Line Transient Response
Figure 15. Load Transient Response
Figure 16. Load Transient Response
Figure 17. Load Transient Response
Figure 18. Load Transient Response
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
Typical Characteristics (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 4.7 μF, CIN = 1 μF all voltage options, ON/OFF pin tied to
VIN.
Figure 19. Short-Circuit Current
Figure 20. Instantaneous Short Circuit Current vs
Temperature
Figure 21. Short-Circuit Current
Figure 22. Instantaneous Short-Circuit Current vs Output
Voltage
Figure 23. Output Impedance vs Frequency
Figure 24. Ripple Rejection
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
11
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 4.7 μF, CIN = 1 μF all voltage options, ON/OFF pin tied to
VIN.
12
Figure 25. Output Noise Density
Figure 26. Output Impedance vs Frequency
Figure 27. Input-to-Output Leakage vs Temperature
Figure 28. Output Reverse Leakage vs Temperature
Figure 29. Turnon Waveform
Figure 30. Turnoff Waveform
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
Typical Characteristics (continued)
Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 4.7 μF, CIN = 1 μF all voltage options, ON/OFF pin tied to
VIN.
Figure 31. ON/OFF Pin Current vs VON/OFF
Figure 32. ON/OFF Threshold vs Temperature
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
13
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
7 Detailed Description
7.1 Overview
The LP2981-N is a 100-mA, fixed-output voltage regulator designed specifically to meet the requirements of
battery-powered applications. Available in assorted output voltages from 2.5 V to 5 V, the device has an output
tolerance of 0.75% for the A grade (1.25% for the non-A version). Using a VIP process, the LP2981-N contains
these features to facilitate battery-powered designs:
• Fixed 5-V, 3.6-V, 3.3-V, 3-V, and 2.5-V output versions
• Very high-accuracy 1.23-V reference
• Low-dropout voltage, typical dropout of 200 mV at 100-mA load current and 7 mV at 1-mA load
• Low ground current, typically 600 μA at 100-mA load and 80 μA at 1-mA load
• A sleep mode feature is available, allowing the regulator to consume only 1 µA (typical) when the ON/OFF pin
is pulled low.
• Overtemperature protection and overcurrent protection circuitry is designed to safeguard the device during
unexpected conditions.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Multiple Voltage Options
To meet the different application requirements, the LP2981-N provides multiple fixed output options from 2.5 V to
5 V.
7.3.2 High-Accuracy Output Voltage
With special careful design to minimize all contributions to the output voltage error, the LP2981-N distinguishes
itself as a very high-accuracy output voltage micropower LDO. This includes a tight initial tolerance (0.75%
typical), extremely good line regulation (0.007%/V typical), and a very low output voltage temperature coefficient,
making the part an ideal low-power voltage reference.
14
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
Feature Description (continued)
7.3.3 Ultra-Low-Dropout Voltage
Generally speaking, the dropout voltage often refers to the voltage difference between the input and output
voltage (VDO = VIN – VOUT), where the main current pass-FET is fully on in the ohmic region of operation and is
characterized by the classic RDS(ON) of the FET. VDO indirectly specifies a minimum input voltage above the
nominal programmed output voltage at which the output voltage is expected to remain within its accuracy
boundary.
7.3.4 Low Ground Current
LP2981-N uses a vertical PNP process which allows for quiescent currents that are considerably lower than
those associated with traditional lateral PNP regulators, typically 600 μA at 100-mA load and 80 μA at 1-mA load.
7.3.5 Sleep Mode
When pulling the ON/OFF pin to low level, LP2981-N will enter sleep mode, and less than 1-μA quiescent current
is consumed. This function is designed for the application which needs a sleep mode to effectively enhance
battery life cycle.
7.3.6 Short-Circuit Protection (Current Limit)
The internal current-limit circuit is used to protect the LDO against high-load current faults or shorting events. The
LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources
constant current. Therefore, the output voltage falls when load impedance decreases. If a current limit occurs
and the resulting output voltage is low, excessive power may be dissipated across the LDO resulting in a thermal
shutdown of the output. A foldback feature limits the short-circuit current to protect the regulator from damage
under all load conditions. If OUT is forced below 0 V before EN goes high and the load current required exceeds
the foldback current limit, the device may not start up correctly.
7.3.7 Thermal Protection
The LP2981-N contains a thermal shutdown protection circuit to turn off the output current when excessive heat
is dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output
cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The
internal protection circuitry of the LM2981-N is designed to protect against thermal overload conditions. The
circuitry is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown
degrades its reliability.
7.4 Device Functional Modes
7.4.1 Operation with VOUT(TARGET) + 1 V ≤ VIN < 16 V
The device operates if the input voltage is equal to, or exceeds, VOUT(TARGET) + 0.6 V. At input voltages below the
minimum VIN requirement, the device does not operate correctly and output voltage may not reach target value.
7.4.2 Operation With ON/OFF Control
If the voltage on the ON/OFF pin is less than 0.15 V, the device is disabled, and the shutdown current does not
exceed 1 μA. Raising ON/OFF above 1.4 V initiates the start-up sequence of the device.
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
15
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP2981-N is a linear voltage regulator operating from 2.1 V to 16 V on the input and regulates voltages
between 2.5 V to 5 V with 0.75% accuracy and 100-mA maximum output current. Efficiency is defined by the
ratio of output voltage to input voltage because the LP2981-N is a linear voltage regulator. To achieve high
efficiency, the dropout voltage (VIN – VOUT) must be as small as possible, thus requiring a very-low-dropout LDO.
Successfully implementing an LDO in an application depends on the application requirements. If the
requirements are simply input voltage and output voltage, compliance specifications (such as internal power
dissipation or stability) must be verified to ensure a solid design. If timing, start-up, noise, power supply rejection
ratio (PSRR), or any other transient specification is required, then the design becomes more challenging.
8.2 Typical Application
VIN
IN
VOUT
OUT
COUT
CIN
GND
ON/OFF
ON/OFF
NC
Copyright © 2016, Texas Instruments Incorporated
*ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used.
**Minimum output capacitance is shown to insure stability over full load current range. More capacitance provides
superior dynamic performance and additional stability margin (see Capacitor Characteristics).
***Do not make connections to this pin.
Figure 33. LP2981-N Typical Application
8.2.1 Design Requirements
PARAMETER
DESIGN REQUIREMENT
Input voltage
5 V ±10%, provided by the DC-DC converter switching at 1 MHz
Output voltage
3.3 V ±5%
Output current
100 mA (maximum), 1 mA (minimum)
RMS noise, 300 Hz to 50 kHz
< 1 mVRMS
PSRR at 1 kHz
> 40 dB
8.2.2 Detailed Design Procedure
8.2.2.1 External Capacitors
Like any low-dropout regulator, the external capacitors used with the LP2981-N must be carefully selected to
assure regulator loop stability.
16
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
8.2.2.1.1 Input Capacitor
An input capacitor with a value ≥ 1 μF is required with the LP2981-N (amount of capacitance can be increased
without limit).
This capacitor must be located a distance of not more than 0.5 inches from the input pin of the LP2981-N and
returned to a clean analog ground. Any good quality ceramic or tantalum can be used for this capacitor.
8.2.2.1.2 Output Capacitor
The output capacitor must meet both the requirement for minimum amount of capacitance and equivalent series
resistance (ESR) value. Curves are provided which show the allowable ESR range as a function of load current
for various output voltages and capacitor values (refer to Figure 36, Figure 37, Figure 38, and Figure 39).
NOTE
Important: The output capacitor must maintain its ESR in the stable region over the full
operating temperature range to ensure stability. Also, capacitor tolerance and variation
with temperature must be considered to ensure the minimum amount of capacitance is
provided at all times.
This capacitor should be located not more than 0.5 inches from the OUT pin of the LP2981-N and returned to a
clean analog ground.
8.2.2.2 Capacitor Characteristics
8.2.2.2.1 Tantalum
Tantalum capacitors are the best choice for use with the LP2981-N. Most good quality tantalums can be used
with the LP2981-N, but check the manufacturer's data sheet to be sure the ESR is in range.
It is important to remember that ESR increases at lower temperatures and a capacitor that is near the upper limit
for stability at room temperature can cause instability when it gets cold.
In applications which must operate at very low temperatures, it may be necessary to parallel the output tantalum
capacitor with a ceramic capacitor to prevent the ESR from going up too high (see below for important
information on ceramic capacitors).
8.2.2.2.2 Ceramic
Ceramic capacitors are not recommended for use at the output of the LP2981-N. This is because the ESR of a
ceramic can be low enough to go below the minimum stable value for the LP2981-N. A 2.2-μF ceramic was
measured and found to have an ESR of about 15 mΩ, which is low enough to cause oscillations.
If a ceramic capacitor is used on the output, a 1-Ω resistor should be placed in series with the capacitor.
8.2.2.2.3 Aluminum
Because of large physical size, aluminum electrolytics are not typically used with the LP2981-N. They must meet
the same ESR requirements over the operating temperature range, more difficult because of their steep increase
at cold temperature.
An aluminum electrolytic can exhibit an ESR increase of as much as 50x when going from 20°C to −40°C. Also,
some aluminum electrolytics are not operational below −25°C because the electrolyte can freeze.
8.2.2.3 Reverse Current Path
The internal PNP power transistor used as the pass element in the LP2981-N has an inherent diode connected
between the regulator output and input. During normal operation (where the input voltage is higher than the
output) this diode is reverse biased (See Figure 34).
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
17
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
LP2981-N
VIN
VOUT
PNP
GND
Figure 34. LP2981-N Reverse Current Path
However, if the input voltage is more than a VBE below the output voltage, this diode will turn ON and current will
flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into
the VIN pin and out the ground pin, which can damage the part.
The internal diode can also be turned on if the input voltage is abruptly stepped down to a voltage which is a VBE
below the output voltage.
In any application where the output voltage may be higher than the input voltage, an external Schottky diode
must be connected from VIN to VOUT (cathode on VIN, anode on VOUT; see Figure 35), to limit the reverse voltage
across the LP2981-N to 0.3 V (see Absolute Maximum Ratings).
SCHOTTKY DIODE
LP2981-N
VIN
VOUT
PNP
GND
Figure 35. Adding External Schottky Diode Protection
8.2.2.4 ON and OFF Input Operation
The LP2981-N is shut off by pulling the ON/OFF input low, and turned on by driving the input high. If this feature
is not to be used, the ON/OFF input should be tied to VIN to keep the regulator on at all times (the ON/OFF input
must not be left floating).
To ensure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and
below the specified turnon/turnoff voltage thresholds which specify an ON or OFF state (see Electrical
Characteristics).
18
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
The ON/OFF signal may come from either a totem-pole output, or an open-collector output with pullup resistor to
the LP2981-N input voltage or another logic supply. The high-level voltage may exceed the LP2981-N input
voltage, but must remain within the Absolute Maximum Ratings for the ON/OFF pin.
It is also important that the turnon/turnoff voltage signals applied to the ON/OFF input have a slew rate which is
greater than 40 mV/μs.
NOTE
IMPORTANT: The regulator shutdown function will not operate correctly if a slow-moving
signal is applied to the ON/OFF input.
8.2.3 Application Curves
Figure 36. 5-V, 3.3-μF ESR Curves
Figure 37. 5-V, 10-μF ESR Curves
Figure 38. 3-V, 3.3-μF ESR Curves
Figure 39. 3-V, 10-μF ESR Curves
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
19
LP2981-N
SNOS773N – MARCH 2000 – REVISED APRIL 2016
www.ti.com
9 Power Supply Recommendations
The LP2981-N is designed to operate from an input voltage supply range between 2.1 V and 16 V. The input
voltage range provides adequate headroom for the device to have a regulated output. This input supply must be
well regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the output
noise performance.
10 Layout
10.1 Layout Guidelines
For best overall performance, place all circuit components on the same side of the circuit board and as near as
practical to the respective LDO pin connections. Place ground return connections to the input and output
capacitors, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side,
copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and
negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and
thereby reduces load-current transients, minimizes noise, and increases circuit stability. A ground reference
plane is also recommended and is either embedded in the PCB itself or located on the bottom side of the PCB
opposite the components. This reference plane serves to assure accuracy of the output voltage, shield noise,
and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In most applications, this
ground plane is necessary to meet thermal requirements.
10.2 Layout Example
VIN
Input
Capacitor
VOUT
IN
GND
OUT
Output
Capacitor
Ground
ON/OFF
ON/OFF
NC
Figure 40. LP2981-N Layout Example
20
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
LP2981-N
www.ti.com
SNOS773N – MARCH 2000 – REVISED APRIL 2016
11 Device and Documentation Support
11.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LP2981-N
21
PACKAGE OPTION ADDENDUM
www.ti.com
10-Sep-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP2981AIM5-2.5
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L0CA
LP2981AIM5-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0CA
LP2981AIM5-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L05A
LP2981AIM5-3.3
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L04A
LP2981AIM5-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L04A
LP2981AIM5-3.6
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L0JA
LP2981AIM5-3.6/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0JA
LP2981AIM5-5.0
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L03A
LP2981AIM5-5.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L03A
LP2981AIM5X-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L05A
LP2981AIM5X-3.3
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L04A
LP2981AIM5X-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L04A
LP2981AIM5X-3.6/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0JA
LP2981AIM5X-5.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L03A
LP2981IM5-2.5
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L0CB
LP2981IM5-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0CB
LP2981IM5-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L05B
LP2981IM5-3.3
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L04B
LP2981IM5-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L04B
LP2981IM5-3.6/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0JB
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
10-Sep-2015
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP2981IM5-5.0
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
L03B
LP2981IM5-5.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L03B
LP2981IM5X-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L05B
LP2981IM5X-3.3
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L04B
LP2981IM5X-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L04B
LP2981IM5X-3.6/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L0JB
LP2981IM5X-5.0
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
L03B
LP2981IM5X-5.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L03B
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Sep-2015
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LP2981AIM5-2.5
SOT-23
DBV
5
1000
178.0
8.4
LP2981AIM5-2.5/NOPB
SOT-23
DBV
5
1000
178.0
LP2981AIM5-3.0/NOPB
SOT-23
DBV
5
1000
178.0
LP2981AIM5-3.3
SOT-23
DBV
5
1000
LP2981AIM5-3.3/NOPB
SOT-23
DBV
5
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5-3.6
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5-3.6/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5-5.0
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5-5.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5X-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5X-3.3/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5X-3.6/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5X-5.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981AIM5X-3.3
LP2981IM5-2.5
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5-2.5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5-3.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5-3.3
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2015
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LP2981IM5-3.3/NOPB
SOT-23
DBV
5
1000
178.0
8.4
LP2981IM5-3.6/NOPB
SOT-23
DBV
5
1000
178.0
8.4
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5-5.0
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5-5.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5X-3.0/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5X-3.3
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5X-3.3/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5X-3.6/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5X-5.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP2981IM5X-5.0/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP2981AIM5-2.5
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-3.3
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-3.6
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-3.6/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2015
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP2981AIM5-5.0
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5-5.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981AIM5X-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981AIM5X-3.3
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981AIM5X-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981AIM5X-3.6/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981AIM5X-5.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981IM5-2.5
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-3.3
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-3.6/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-5.0
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5-5.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LP2981IM5X-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981IM5X-3.3
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981IM5X-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981IM5X-3.6/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981IM5X-5.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP2981IM5X-5.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages