LCDA15C-6 Low Capacitance TVS Diode Array For Multi-mode Tranciever Protection PROTECTION PRODUCTS Description Features The LCDA15C-6 has been specifically designed to protect sensitive components which are connected to data and transmission lines from over voltages caused by electrostatic discharge (ESD), electrical fast transients (EFT), and lightning. The low capacitance array configuration of the LCDA15C-6 allows the user to protect six high-speed data or I/O lines. They may be used on systems operating from 5 to 15 Volts. The high surge capability (500W, tp=8/20µs) makes the LCDA15C-6 suitable for telecommunications systems operating in harsh transient environments. The low inductance construction minimizes voltage overshoot during high current surges. The features of the LCDA15C-6 are ideal for protecting multi-protocol transceivers in WAN applications such as Frame Relay systems, routers, and switches. Transient protection for high-speed data lines to IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) IEC 61000-4-5 (Lightning) 0.5kV, 12A (8/20µs) Protects six I/O lines Low capacitance for high-speed interfaces High surge capability Low clamping voltage Solid-state silicon avalanche technology Mechanical Characteristics JEDEC SO-8 package Molding compound flammability rating: UL 94V-0 Marking : Part number, date code, logo Packaging : Tape and Reel per EIA 481 Applications Multi-Mode Transceiver Protection WAN Equipment: CSU/DSU Multiplexers Routers ISP Equipment Customer Premise Equipment Protection for any of the following interfaces: RS-232 (V.28) RS-422 (V.11, X.21) RS-449 (V.11/V.10) RS-485 Circuit Diagram Schematic & PIN Configuration Pin 1 Pin 4 and 5 SO-8 (Top View) Revision 08/15/06 1 www.semtech.com LCDA15C-6 PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20µs) Pp k 500 Watts Peak Pulse Current (tp = 8/20µs) IP P 15 A Lead Soldering Temp erature TL 260 (10 sec.) °C Op erating Temp erature TJ -55 to +125 °C TSTG -55 to +150 °C Storage Temp erature Electrical Characteristics LCDA15C-6 Parameter Symbol Conditions Minimum Typical Maximum Units 15 V Reverse Stand-Off Voltage VRWM Reverse Breakdown Voltage V BR It= 1mA Reverse Leakage Current IR VRWM = 15V, T=25°C 5 µA Clamp ing Voltage VC IPP = 1A, tp = 8/20µs Line-to-Ground 24 V Clamp ing Voltage VC IPP = 15A, tp = 8/20µs Line-to-Ground 33 V Junction Cap acitance Cj Between I/O p ins and Ground VR = 0V, f = 1MHz 8 15 pF Between I/O p ins VR = 0V, f = 1MHz 3 2005 Semtech Corp. 2 16.7 V pF www.semtech.com LCDA15C-6 PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 110 10 Peak Pulse Power - Ppk (kW) 100 % of Rated Power or IPP 90 1 0.1 80 70 60 50 40 30 20 10 0.01 0 0.1 1 10 100 0 1000 25 50 Pulse Waveform 100 125 150 175 Clamping Voltage vs. Peak Pulse Current 28 110 Waveform Parameters: tr = 8µs td = 20µs 90 80 70 26 Clamping Voltage - VC (V) 100 Percent of IPP 75 Ambient Temperature - TA (oC) Pulse Duration - tp (µs) -t e 60 50 40 td = IPP/2 30 20 24 22 20 18 16 Waveform Parameters: tr = 8µs td = 20µs 14 12 10 10 0 0 5 10 15 20 25 0 30 2 4 6 8 10 12 14 16 Peak Pulse Current - IPP (A) Time (µs) Capacitance vs. Reverse Voltage Capacitance - Cj (pF) 9 8.5 8 7.5 f=1MHz Line-to-Ground 7 0 1 2 3 4 5 6 7 8 9 10 11 12 Reverse Voltage - VR (V) 2005 Semtech Corp. 3 www.semtech.com LCDA15C-6 PROTECTION PRODUCTS Applications Information Device Connection Device Connection Options for Protection of Six HighSpeed Data Lines The LCDA15C-6 may be configured to protect up to six I/O lines operating between 5 and 15V. It may be used to protect the most popular serial data interface standard lines making it ideal for use in equipment utilizing multi-mode transceivers. Data lines are connected at pins 1, 2, 3, 6, 7, and 8. Pins 4 and 5 are connected to ground. For best results, these pins should be connected directly to a ground plane on the board. The path length should be kept as short as possible to minimize parasitic inductance. Multi-Mode Transceiver Protection Multi-Mode Tranceiver Protection Example A typical multi-mode transceiver protection circuit is shown. The LCDA15C-6 is used to protect I/O lines with external connections. The LCDA15C-6 adds a maximum loading capacitance of 15pF with a working voltage of 15V. This allows the transceiver to safely operate in all modes without clipping or degradation of the signal. With proper design and layout, the transceiver port can be protected to >15kV (HBM per IEC 61000-4-2). Circuit Board Layout Recommendations for Suppression of ESD. Good circuit board layout is critical for the suppression of fast rise-time transients such as ESD. The following guidelines are recommended: z Place the LCDA15C-6 near the input terminals or connectors to restrict transient coupling. z Minimize the path length between the LCDA15C-6 and the protected line. z Minimize all conductive loops including power and ground loops. z The ESD transient return path to ground should be kept as short as possible. z Never run critical signals near board edges. z Use ground planes whenever possible. 2005 Semtech Corp. Matte Tin Lead Finish Matte tin has become the industry standard lead-free replacement for SnPb lead finishes. A matte tin finish is composed of 100% tin solder with large grains. Since the solder volume on the leads is small compared to the solder paste volume that is placed on the land pattern of the PCB, the reflow profile will be determined by the requirements of the solder paste. Therefore, these devices are compatible with both lead-free and SnPb assembly techniques. In addition, unlike other lead-free compositions, matte tin does not have any added alloys that can cause degradation of the solder joint. 4 www.semtech.com LCDA15C-6 PROTECTION PRODUCTS Outline Drawing - SO-8 A h D e N h H 2X E/2 E1 E 1 0.25 L (L1) e/2 DETAIL B 01 A D aaa C SEATING PLANE A2 A C SEE DETAIL A .053 .069 .010 .004 .065 .049 .012 .020 .010 .007 .189 .193 .197 .150 .154 .157 .236 BSC .050 BSC .010 .020 .016 .028 .041 (.041) 8 8° 0° .004 .010 .008 1.35 1.75 0.10 0.25 1.25 1.65 0.31 0.51 0.17 0.25 4.80 4.90 5.00 3.80 3.90 4.00 6.00 BSC 1.27 BSC 0.25 0.50 0.40 0.72 1.04 (1.04) 8 0° 8° 0.10 0.25 0.20 SIDE VIEW A1 bxN bbb DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX A A1 A2 b c D E1 E e h L L1 N 01 aaa bbb ccc c GAGE PLANE 2 ccc C 2X N/2 TIPS DIM C A-B D NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD MS-012, VARIATION AA. Land Pattern - SO-8 X DIM (C) G C G P X Y Z Z Y DIMENSIONS INCHES MILLIMETERS (.205) .118 .050 .024 .087 .291 (5.20) 3.00 1.27 0.60 2.20 7.40 P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 2. REFERENCE IPC-SM-782A, RLP NO. 300A. 2005 Semtech Corp. 5 www.semtech.com LCDA15C-6 PROTECTION PRODUCTS Ordering Information Part Number Lead Finish Qty per Reel Reel Size LCDA15C-6.TB SnPb 500 7 Inch LCDA15.C-6TBT Pb Free 500 7 inch SnPb 95/Tube N/A Pb Free 95/Tube N/A LCDA15C-6 LCDA15C-6.T Note: Lead-free devices are RoHS/WEEE Compliant Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 2005 Semtech Corp. 6 www.semtech.com