Features Regulated Converters ● ● ● ● ● ● ● ● ● POWERLINE 2:1 Wide Input Voltage Range Safety standards and approvals: EN 60950 certified, rated for 250VAC (LVD test report) 3 Watts Regulated Output Power 1.6kVDC Isolation Over Current Protection Five-Sided Shield Standard DIP24 and SMD-Pinning UL 1950 Component Recognized High Efficiency to 82% DC/DC-Converter RP03S_DA Series Selection Guide 12V, 24V and 48V Input Types Part Number Input Current(4) Efficiency(5) Capacitive(6) Load max. mA % µF DIP24 (SMD) Input Range VDC Output Voltage VDC Output Current mA RP03-123.3SA** 9-18 3.3 500 196 74 2200 RP03-1205SA** 9-18 5 500 289 76 1000 RP03-1212SA** 9-18 12 250 329 80 220 RP03-1215SA** 9-18 15 200 325 81 150 RP03-243.3SA** 18-36 3.3 500 101 72 2200 RP03-2405SA** 18-36 5 500 149 74 1000 RP03-2412SA** 18-36 12 250 171 77 220 RP03-2415SA** 18-36 15 200 169 78 150 RP03-483.3SA** 36-75 3.3 500 50 73 2200 RP03-4805SA** 36-75 5 500 75 74 1000 RP03-4812SA** 36-75 12 250 83 79 220 RP03-4815SA** 36-75 15 200 84 78 150 RP03-1205DA** 9-18 ±5 ±250 282 78 ±470 RP03-1212DA** 9-18 ±12 ±125 329 80 ±100 RP03-1215DA** 9-18 ±15 ±100 321 82 ±68 RP03-2405DA** 18-36 ±5 ±250 149 74 ±470 RP03-2412DA** 18-36 ±12 ±125 171 77 ±100 RP03-2415DA** 18-36 ±15 ±100 169 78 ±68 RP03-4805DA** 36-75 ±5 ±250 76 73 ±470 RP03-4812DA** 36-75 ±12 ±125 83 79 ±100 RP03-4815DA** 36-75 ±15 ±100 86 86 ±68 3 Watt DIP24 & SMD, Single & Dual Output ** add Suffix SMD for SMD package Description The A-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards. 166 April-2005 www.recom-international.com RP03-S_DA Series POWERLINE DC/DC-Converter Derating-Graph (Ambient Temperature) RP03-4805SA/M1 125 125 100 100 75 75 Natural Convection 50 Output Power (%) Output Power (%) RP03-4805SA 25 0 -25 -10 0 Natural Convection 50 25 0 -40 -25 -10 0 50 60 70 80 90 100 85 Ambient Temperature Range (°C) 50 60 70 80 90 100 Ambient Temperature Range (°C) Derating graphes are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at [email protected] Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 24V nominal input 48V nominal input Input Filter Input Surge Voltage (100 ms max.) Pi Type 12V Input 24V Input 48V Input Input Reflected Ripple (nominal Vin and full load) 36VDC 50VDC 100VDC 20mAp-p Start Up Time (nominal Vin and constant resistor load) 350ms typ. Output Power 3W max. Output Voltage Accuracy (full Load and nominal Vin) ±2% Minimum Load (see Note 1) 10% of FL Line Regulation (LL-HL at full load) Load Regulation (25% to 100% FL) 9-18VDC 18-36VDC 36-75VDC ±0.2% Single Dual Cross Regulation (asymmetrical load 25%/100% FL) ±0.2% ±1% ±5% Ripple and Noise (20MHz bandwith) 50mVp-p Temperature Coefficient ±0.02%/°C, max. Transient Response (25% load step change) 200µS Over Load Protection (% of full load at nominal Vin) 180% typ Short Circuit Protection Continuous, automatic recovery Efficiency see „Selection Guide“ table continued on next page www.recom-international.com April-2005 167 POWERLINE RP03-S_DA Series DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Isolation Voltage In to out I/O to case I/O to case 1.600VDC min. DIP type 1.600VDC min. SMD type 1.000VDC min. Isolation Resistance 109 Ω min. Isolation Capacitance 300pF max. Operating Frequency 300kHz typ. Approved to Safety Standards Operating Temperature Range UL 1950, EN60950 Standard M1 (see note 3) -25°C to +85°C (with derating) -40°C to +85°C (non-derating) Maximum Case Temperature +100°C Storage Temperature Range -55°C to +105°C Thermal Impedance Natural convection Thermal Shock 20°C/Watt MIL-STD-810D Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Nickel-Coated copper Base Material Non-conductive black plastic Potting Material Epoxy (UL94-V0) Conducted Emissions Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Weight DIP SMD 16g 18g Dimensions DIP SMD 31.8 x 20.3 x 10.2mm 32.0 x 20.3 x 10.9mm 3.155 x 106 Hours MTBF (see note 2) Notes : 1. The RP03 A series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40 °C (Ground fixed and controlled environment). 3. M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than the standard version. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. See application notes for EMI-filtering. 168 April-2005 www.recom-international.com POWERLINE RP03-S_DA Series DC/DC-Converter Package Style and Pinning (mm) DIP24 Package Style 3rd angle projection 31.80 20.30 10.20 3.8 4.60 5.10 17.80 15.20 Pin Connections Pin # 0.25 x 0.50 Rectangular Pin 9 10 11 2 3 Bottom View 16 15 14 23 22 Single Dual 2 –Vin 3 –Vin 9 NC 10 NC 11 NC 14 +Vout 15 NC 16 –Vout 22 +Vin 23 +Vin NC = No Connection –Vin –Vin Com NC –Vout +Vout NC Com +Vin +Vin Pin Pitch Tolerance ±0.35 mm SMD Package Style 32.00 20.30 31.40 SMD Package Style 11.20 2.54 Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 10.90 3.81 21.30 6.35 25.40 Pin Connections Pin # Pin area 0.1 x 0.50 2.54 0.50 1.60 2.40 9 10 11 12 1 2 3 4 5 23.40 Bottom View 26.54 24.14 24 23 22 21 20 16 15 14 13 11 x 2.54 Top View 1 27.94 Single Dual 2 –Vin 3 –Vin 9 NC 10 NC 11 NC 14 +Vout 15 NC 16 –Vout 22 +Vin 23 +Vin Others NC NC = No Connection –Vin –Vin Com NC –Vout +Vout NC Com +Vin +Vin NC Pin Pitch Tolerance ±0.35 mm www.recom-international.com April-2005 169