ACST2 Overvoltage protected AC switch Features OUT ■ Triac with overvoltage crowbar technology ■ High noise immunity: static dV/dt > 500 V/µs ■ ACST210-8FP, in the TO-220FPAB package, provides insulation voltage rated at 1500 V rms G COM G OUT COM Benefits ■ Enables equipment to meet IEC 61000-4-5 ■ High off-state reliability with planar technology ■ Needs no external overvoltage protection ■ Reduces component count ■ Interfaces directly with the micro-controller ■ High immunity against fast transients described in IEC 61000-4-4 standards Figure 1. Functional diagram OUT Applications G ■ AC on/off static switching in appliances and industrial control systems ■ Driving low power highly inductive loads like solenoid, pump, fan, and micro-motor Description The ACST2 series belongs to the ACS™/ACST power switch family built with A.S.D.® (application specific discrete) technology. This high performance device is suited to home appliances or industrial systems and drives loads up to 2 A. This ACST2 switch embeds a Triac structure with a high voltage clamping device to absorb the inductive turn-off energy and withstand line transients such as those described in the IEC 61000-4-5 standards. The component needs a low gate current to be activated (IGT < 10 mA) and still shows a high electrical noise immunity complying with IEC standards such as IEC 61000-4-4 (fast transient burst test). July 2010 DPAK ACST210-8B TO-220FPAB ACST210-8FP COM Table 1. Device summary Symbol Value Unit IT(RMS) 2 A VDRM/VRRM 800 V IGT 10 mA TM: ACS is a trademark of STMicroelectronics ®: A.S.D. is a registered trademark of STMicroelectronics Doc ID 13304 Rev 3 1/13 www.st.com 13 Characteristics ACST2 1 Characteristics Table 2. Absolute maximum ratings (limiting values) Symbol Parameter Value TO-220FPAB IT(RMS) On-state rms current (full sine wave) Non repetitive surge peak on-state current (full cycle sine wave, TJ initial = 25 °C) ITSM ² ² It dI/dt Tc = 105 °C A 2 DPAK Tc = 110 °C F = 60 Hz t = 16.7 ms 8.4 F = 50 Hz t = 20 ms 8.0 I t Value for fusing tp = 10 ms Critical rate of rise of on-state current IG = 2 x IGT, tr = 100 ns F = 120 Hz Unit A 0.5 A ²s Tj = 125 °C 50 A/µs VPP (1) Non repetitive line peak mains voltage (1) Tj = 25 °C 2 kV PG(AV) Average gate power dissipation Tj = 125 °C 0.1 W PGM Peak gate power dissipation (tp = 20 µs) Tj = 125 °C 10 W IGM Peak gate current (tp = 20 µs) Tj = 125 °C 1.6 A Tstg Tj Storage junction temperature range Operating junction temperature range -40 to +150 -40 to +125 °C 260 °C 1500 V Tl Maximum lead soldering temperature during 10 s (at 3 mm from plastic case) VINS(RMS) Insulation rms voltage T0-220FPAB 1. According to test described in IEC 61000-4-5 standard and Figure 18 Table 3. Electrical characteristics (Tj = 25 °C, unless otherwise specified) Symbol Test conditions Quadrant Unit IGT(1) VOUT = 12 V, RL = 33 Ω I - II - III MAX 10 mA VGT VOUT = 12 V, RL = 33 Ω I - II - III MAX 1.1 V VGD VOUT = VDRM, RL = 3.3 kΩ,Tj = 125 °C I - II - III MIN 0.2 V MAX 10 mA I - III MAX 25 II MAX 35 VOUT = 67% VDRM gate open, Tj = 125 °C MIN 500 V/µs (dV/dt)c = 15 V/µs, Tj = 125 °C MIN 0.5 A/ms ICL = 0.1 mA, tp = 1 ms, Tj = 25 °C MIN 850 V IH (2) IOUT = 100 mA IL (dI/dt)c VCL mA IG = 1.2 x IGT dV/dt (2) (2) 1. Minimum IGT is guaranteed at 5% of IGT max 2. For both polarities of OUT pin referenced to COM pin 2/13 Value Doc ID 13304 Rev 3 ACST2 Characteristics Table 4. Static electrical characteristics Symbol VTM(1) (1) Test conditions Value Unit ITM = 2.8 A, tp = 500 µs Tj = 25 °C MAX 2 V Threshold voltage Tj = 125 °C MAX 0.9 V RD(1) Dynamic resistance Tj = 125 °C MAX 250 mΩ IDRM IRRM 10 µA VOUT = VDRM / VRRM 0.5 mA VTO Tj = 25 °C MAX Tj = 125 °C 1. For both polarities of OUT pin referenced to COM pin Table 5. Thermal resistances Symbol Parameter Value DPAK Rth(j-c) Unit 4.5 Junction to case (AC) TO-220FPAB 7 TO-220FPAB 60 DPAK 70 °C/W Rth(j-a) Junction to ambient SCU (1)= 0.5 cm² 1. SCU = copper surface under tab Figure 2. Maximum power dissipation versus Figure 3. on-state rms current (full cycle) P(W) On-state rms current versus case temperature IT(RMS)(A) 2.8 2.4 α=180 ° 2.2 2.4 DPAK 2.0 1.8 2.0 TO-220FPAB 1.6 1.4 1.6 1.2 1.2 1.0 0.8 0.8 0.6 180° 0.4 0.4 0.2 0.4 0.6 0.8 1.0 TC(°C) 0.0 0.0 0.0 α=180 ° 0.2 IT(RMS)(A) 1.2 1.4 1.6 1.8 2.0 0 Doc ID 13304 Rev 3 25 50 75 100 125 3/13 Characteristics Figure 4. ACST2 On-state rms current versus ambient temperature Figure 5. IT(RMS) (A) 1.00 1.8 Relative variation of thermal impedance versus pulse duration TO-220FPAB K=[Zth/Rth] α=180 ° Printed circuit board FR4 Natural convection SCU=0.5 cm² 1.6 1.4 Zth(j-c) 1.2 Zth(j-a) 1.0 0.10 0.8 0.6 0.4 0.2 Tamb(°C) 0.0 0 25 Figure 6. 1.0E+00 50 75 100 125 Relative variation of thermal impedance versus pulse duration DPAK 1.0E-04 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 Relative variation of gate trigger, holding and latching current versus junction temperature IGT, IH, IL [T J] / IGT, IH, IL [T j=25 °C] 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 Zth(j-c) Zth(j-a) 1.0E-01 DPAK tP(s) 1.0E-02 1.0E-04 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 Figure 8. 1.0E-03 Figure 7. K=[Zth/Rth] TO-220FPAB tP(s) 0.01 Relative variation of static dV/dt versus junction temperature IL & IH Tj(°C) Figure 9. 2.0 VOUT=540 V Typical values -40 -30 -20 -10 0 dV/dt [T j] / dV/dt [T j=125 °C] 100 IGT 10 20 30 40 50 60 70 80 90 100 110 120 130 Relative variation of critical rate of decrease of main current versus reapplied dV/dt (typical values) (dI/dt)c [ (dV/dt) c ] / Specified (dI/dt) c VOUT=300 V 1.8 1.6 1.4 1.2 1.0 10 0.8 0.6 0.4 0.2 T j(°C) 25 4/13 (dV/dt)c(V/µs) 0.0 1 50 75 100 125 0.1 Doc ID 13304 Rev 3 1.0 10.0 100.0 ACST2 Characteristics Figure 10. Relative variation of critical rate of decrease of main current versus junction temperature (dI/dt)c [T j] / (dI/dt)c [T j=125 °C] Figure 11. Surge peak on-state current versus number of cycles 9 20 VOUT=300 V 18 ITSM (A) 8 16 t=20ms 7 14 One cycle Non repetitive Tj initial=25 °C 6 12 5 10 4 8 Repetitive TC=110 °C 3 6 2 4 1 2 T j(°C) Number of cycles 0 0 25 50 75 100 125 1 10 100 1000 Figure 12. Non repetitive surge peak on-state Figure 13. On-state characteristics (maximum current and corresponding value values) of I²t ITSM(A), I²t (A²s) 100.0 ITM(A) 1.E+01 Tj initial=25 °C ITSM Tj=125 °C 1.E+00 10.0 1.0 1.E-01 I²t sinusoidal pulse with width tP < 10 ms 0.1 0.01 TJ max. : VTO= 0.90 V RD= 250 mW VTM(V) tP(ms) 0.10 Tj=25 °C 1.E-02 1.00 0.0 10.00 Figure 14. Thermal resistance junction to ambient versus copper surface under tab DPAK 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Figure 15. Relative variation of clamping voltage VCL versus junction temperature Rth(j-a) (°C/W) VCL [T j] / VCL [T j=25 °C] 1.20 100 DPAK printed circuit board FR4, copper thickness = 35 µm 90 1.15 80 1.10 70 60 1.05 50 1.00 40 30 0.95 20 0.90 10 T j(°C) SCU(cm²) 0 0 5 10 15 20 0.85 25 30 35 40 -40 Doc ID 13304 Rev 3 -20 0 20 40 60 80 100 120 140 5/13 Application information ACST2 2 Application information 2.1 Typical application description The ACST2 device has been designed to switch on and off highly inductive or resistive loads such as pump, valve, fan, or bulb lamp. Thanks to its high sensitivity (IGT max = 10 mA), the ACST2 can be driven directly by logic level circuits through a resistor as shown on the typical application diagram. Thanks to its thermal and turn-off commutation performances, the ACST2 switch can drive, without any additional snubber, an inductive load up to 2 A. Figure 16. AC induction motor control – typical diagram Line L AC Mains AC LOAD R ACST2 Rg Power supply 6/13 Doc ID 13304 Rev 3 MCU ACST2 2.2 Application information AC line transient voltage ruggedness In comparison with standard Triacs, which are not robust against surge voltage, the ACST2 is self-protected against over-voltage, specified by the new parameter VCL. In addition, the ACST2 is a sensitive device (IGT = 10 ma), but provides a high noise immunity level againast fast transients. The ACST2 switch can safely withstand AC line transient voltages either by clamping the low energy spikes, such as inductive spikes at switch off, or by switching to the on state (for less than 10 ms) to dissipate higher energy shocks through the load. This safety feature works even with high turn-on current ramp up. The test circuit of Figure 17 represents the ACST2 application, and is used to stress the ACST switch according to the IEC 61000-4-5 standard conditions. With the additional effect of the load which is limiting the current, the ACST switch withstands the voltage spikes up to 2 kV on top of the peak line voltage. The protection is based on an overvoltage crowbar technology. The ACST2 folds back safely to the on state as shown in Figure 18. The ACST2 recovers its blocking voltage capability after the surge and the next zero current crossing. Such a non repetitive test can be done at least 10 times on each AC line voltage polarity. Figure 17. Overvoltage ruggedness test circuit for resistive and inductive loads for IEC 61000-4-5 standards R = 20 Ω, L = 10 µH, VPP = 2 kV Surge generator 2kV surge Rgene Model of the load Filtering unit R L ACST210-8x AC Mains Rg Doc ID 13304 Rev 3 7/13 Application information ACST2 Figure 18. Typical current and voltage waveforms across the ACST2 during IEC 61000-4-5 standard test V peak = V CL 1.2/50 µs voltage surge V 0 8/20 µs current surge I 0 2.3 Electrical noise immunity The ACST2 is a sensitive device (IGT = 10 mA) and can be controlled directly though a simple resistor by a logic level circuit, and still provides a high electrical noise immunity. The intrinsic immunity of the ACST2 is shown by the specified dV/dt equal to 500 V/µs @ 125 °C. This immunity level is 5 to 10 times higher than the immunity provided by an equivalent standard technology Triac with the same sensitivity. In other words, the ACST2 is sensitive, but has an immunity usually available only for non-sensitive device (IGT higher than 35 mA). 8/13 Doc ID 13304 Rev 3 ACST2 3 Ordering information scheme Ordering information scheme Figure 19. Ordering information scheme ACS T 2 10 - 8 B TR AC switch Topology T = Triac On-state rms current 2=2A Sensitivity 10 = 10 mA Voltage 8 = 800 V Package FP = TO-220FPAB B = DPAK Delivery mode TR = Tape and reel (DPAK) Blank = Tube (TO-220FPAB, DPAK) Doc ID 13304 Rev 3 9/13 Package information 4 ACST2 Package information ● Epoxy meets UL94, V0 ● Recommended torque (TO-220FPAB): 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 6. TO-220FPAB dimensions Dimensions Ref. A B H Dia L6 L7 L2 L3 L5 F1 L4 Min. Max. Min. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 F2 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 E G1 G 10/13 Inches D F2 F Millimeters Doc ID 13304 Rev 3 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.646 L7 9.00 9.30 0.354 0.366 Dia. 3.00 3.20 0.118 0.126 ACST2 Package information Table 7. DPAK dimensions Dimensions Ref. E A B2 C2 Millimeters Inches Min. Max. Min. Max. A 2.20 2.40 0.086 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.212 C 0.45 0.60 0.017 0.023 C2 0.48 0.60 0.018 0.023 D 6.00 6.20 0.236 0.244 E 6.40 6.60 0.251 0.259 G 4.40 4.60 0.173 0.181 H 9.35 10.10 0.368 0.397 L2 D R H L4 A1 B G R C A2 0.60 MIN. V2 L2 0.80 typ. 0.031 typ. L4 0.60 1.00 0.023 0.039 V2 0° 8° 0° 8° Figure 20. Footprint (dimensions in mm) 6.7 3 3 1.6 2.3 6.7 2.3 1.6 Doc ID 13304 Rev 3 11/13 Ordering information 5 ACST2 Ordering information Table 8. Ordering information Order code Marking ACST210-8FP ACST210-8B Package Weight Base Qty Packing mode TO-220FPAB 2.4g 50 Tube DPAK 0.3g 50 Tube DPAK 0.3g 2500 Tape and Reel ACST2108 ACST210-8B-TR 6 Revision history Table 9. 12/13 Document revision history Date Revision Changes 01-Mar-2007 1 Initial release. 13-Apr-2010 2 Updated ECOPACK statement. Reformatted for consistency with other datasheets in this product class. 01-Jul-2010 3 Updated Figure 19. Doc ID 13304 Rev 3 ACST2 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 13304 Rev 3 13/13