MDU3C data 3 delay devices, inc. TRIPLE, HCMOS-INTERFACED FIXED DELAY LINE (SERIES MDU3C) FEATURES • • • • • • PACKAGES Three independent delay lines Fits standard 14-pin DIP socket Low profile Auto-insertable Input & outputs fully CMOS interfaced & buffered 2 10 T L fan-out capability I1 1 14 VDD I2 3 12 O1 I3 5 10 O3 GND 7 8 O5 MDU3C-xx MDU3C-xxA2 MDU3C-xxB2 MDU3C-xxM I1 N/C I2 N/C I3 N/C GND 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VDD N/C O1 N/C O2 N/C O3 Military SMD MDU3C-xxMC2 DIP Gull-Wing J-Lead Military DIP FUNCTIONAL DESCRIPTION PIN DESCRIPTIONS The MDU3C-series device is a 3-in-1 digitally buffered delay line. The signal inputs (I1-I3) are reproduced at the outputs (O1-O3), shifted in time by an amount determined by the device dash number (See Table). The delay lines function completely independently of each other. I1-I3 O1-O3 VDD GND SERIES SPECIFICATIONS • • • • • • DASH NUMBER SPECIFICATIONS Minimum input pulse width: 100% of total delay Output rise time: 8ns typical Supply voltage: 5VDC ± 5% Supply current: ICCL = 40µa typical ICCH = 60ma typical Operating temperature: 0° to 70° C Temp. coefficient of total delay: 300 PPM/°C O1 O2 Signal Inputs Signal Outputs +5 Volts Ground O3 Part Number MDU3C-10 MDU3C-15 MDU3C-20 MDU3C-25 MDU3C-30 MDU3C-40 MDU3C-50 MDU3C-60 MDU3C-75 MDU3C-100 Delay Per Line (ns) 10 ± 2.0 15 ± 2.0 20 ± 2.0 25 ± 2.0 30 ± 2.0 40 ± 2.0 50 ± 2.5 60 ± 3.0 75 ± 3.7 100 ± 5.0 NOTE: Any dash number between 10 and 100 not shown is also available. VCC 100% 100% 100% I1 I2 I3 GND Functional block diagram 1997 Data Delay Devices Doc #97039 12/12/97 DATA DELAY DEVICES, INC. 3 Mt. Prospect Ave. Clifton, NJ 07013 1 MDU3C APPLICATION NOTES Delay Devices if your application requires device testing at a specific input condition. HIGH FREQUENCY RESPONSE The MDU3C tolerances are guaranteed for input pulse widths and periods greater than those specified in the test conditions. Although the device will function properly for pulse widths as small as 100% of the total delay and periods as small as 200% of the total delay (for a symmetric input), the delays may deviate from their values at low frequency. However, for a given input condition, the deviation will be repeatable from pulse to pulse. Contact technical support at Data POWER SUPPLY BYPASSING The MDU3C relies on a stable power supply to produce repeatable delays within the stated tolerances. A 0.1uf capacitor from VDD to GND, located as close as possible to the VDD pin, is recommended. A wide VDD trace and a clean ground plane should be used. DEVICE SPECIFICATIONS TABLE 1: ABSOLUTE MAXIMUM RATINGS PARAMETER DC Supply Voltage Input Pin Voltage Storage Temperature Lead Temperature SYMBOL VDD VIN TSTRG TLEAD MIN -0.3 -0.3 -55 MAX 7.0 VDD+0.3 150 300 UNITS V V C C NOTES 10 sec TABLE 2: DC ELECTRICAL CHARACTERISTICS (0C to 70C, 4.75V to 5.25V) PARAMETER High Level Output Voltage SYMBOL VOH Low Level Output Voltage VOL High Level Output Current Low Level Output Current High Level Input Voltage Low Level Input Voltage Input Current IOH IOL VIH VIL IIH Doc #97039 12/12/97 MIN 3.98 TYP 4.4 MAX UNITS V 0.15 0.26 V -4.0 4.0 mA mA V V µA 3.15 1.35 0.10 NOTES VDD = 5.0, IOH = MAX VIH = MIN, VIL = MAX VDD = 5.0, IOL = MAX VIH = MIN, VIL = MAX VDD = 5.0 DATA DELAY DEVICES, INC. Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com 2 MDU3C PACKAGE DIMENSIONS 14 12 10 8 Lead Material: Nickel-Iron alloy 42 TIN PLATE 14 12 3 5 8 .410 TYP. 1 1 10 3 5 7 7 .280 MAX. .780 MAX. .820 MAX. .290 MAX. .020 .320 TYP. MAX. .130 ±.030 .015 TYP. .010±.002 .018 TYP. .070 MAX. .350 MAX. .600±.010 14 12 .040 TYP. 10 .010 TYP. 1 3 .090 5 8 14 12 7 .050 TYP. MDU3C-xxA2 (Commercial Gull-Wing) .020 TYP. 9 3 .110 2 .090 3 4 5 6 .100 .600 .780±.020 7 .200 .600 .790 MAX. .350 MAX. .110 TYP. .010±.002 8 .882 ±.005 .710 .590 ±.005 MAX. 1 5 MDU3C-xxB2 (Commercial J-Lead) .040 TYP. 14 13 12 11 10 .320 TYP. .270 TYP. 1 .300 MAX. .050 TYP. 8 10 .430 TYP. .200 .600 .790 MAX. .300 TYP. .040 TYP. .020 TYP. .270 TYP. .020 TYP. MDU3C-xxM (Military DIP) MDU3C-xx (Commercial DIP) .020 TYP. .200 TYP. .018 TYP. .600 TYP. .007 ±.005 7 .280 MAX. .050 ±.010 MDU3C-xxMC2 (Military SMD) Doc #97039 12/12/97 DATA DELAY DEVICES, INC. 3 Mt. Prospect Ave. Clifton, NJ 07013 3 MDU3C DELAY LINE AUTOMATED TESTING TEST CONDITIONS INPUT: o o Ambient Temperature: 25 C ± 3 C Supply Voltage (VDD): 5.0V ± 0.1V Input Pulse: High = 5.0V ± 0.1V Low = 0.0V ± 0.1V Source Impedance: 50Ω Max. Rise/Fall Time: 5.0 ns Max. (measured between 0.5V and 4.5V ) Pulse Width: PWIN = 1.5 x Total Delay Period: PERIN = 10 x Total Delay OUTPUT: Load: Cload: Threshold: 1 FAST-TTL Gate 5pf ± 10% 2.5V (Rising & Falling) NOTE: The above conditions are for test only and do not in any way restrict the operation of the device. PRINTER COMPUTER SYSTEM REF PULSE GENERATOR OUT I1 TRIG I2 DEVICE UNDER TEST (DUT) I3 O1 IN O2 TRIG TIME INTERVAL COUNTER O3 Test Setup PERIN PWIN TRISE INPUT SIGNAL TFALL VIH 4.5V 2.5V 0.5V 4.5V 2.5V 0.5V TRISE VIL TFALL VOH OUTPUT SIGNAL 2.5V 2.5V VOL Timing Diagram For Testing Doc #97039 12/12/97 DATA DELAY DEVICES, INC. Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com 4