AZ695 SENSITIVE SUBMINIATURE RELAY FEATURES • Extremely small footprint utilizing only 0.18 square inch of PCB area • Thin vertical profile only 0.256" wide • 1 Form A contact with up to 5 Amp switching capability • High sensitivity, 100 mW pickup • Dielectric strength 3000 Vrms contact to coil • Coils to 24 VDC • Epoxy sealed for automatic wave soldering and cleaning • UL file E44211; CSA file 74461 CONTACTS GENERAL DATA Arrangement SPST (1 Form A) Ratings Resistive load: Max. switched power: 150 W or 1250 VA Max. switched current: 5 A Max. switched voltage: 150* VDC or 250 VAC Inductive load (p.f. = 0.40, L/R = 7 ms) 2 A at 250 VAC, 30 VDC UL/CSA Ratings 5 A at 30 VDC resistive 5 A at 250 VAC general use 1/10 HP 120 VAC Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Material Resistance Options: Silver cadmium oxide Silver cadmium oxide with gold plating < 30 milliohms initially (6 V, 1 A, voltage drop method) COIL Power At Pickup Voltage (typical) 100 mW Max. Continuous Dissipation 550 mW at 20°C (68°F) ambient 420 mW at 40°C (104°F) ambient Temperature Rise 25°C (45°F) at nominal coil voltage Temperature Max. 105°C (221°F) NOTES Life Expectancy Mechanical Electrical Minimum operations 20 million operations 1 X 105 at 5 A, 30 VDC or 250 VAC Res. Operate Time (typical) 6 ms at nominal coil voltage Release Time (typical) 3 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 750 Vrms between open contacts (at sea level for 1 min.) 3000 Vrms contact to coil Insulation Resistance 100 megohms min. at 20°C, 500 VDC, 50% RH Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 3 grams 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Minimum permissible contact load: SCO contact: 100 mA at 5 VDC SCO contact with gold plating: 10 mA at 5 VDC 4. Specifications subject to change without notice. 7/12/01W AZ695 RELAY ORDERING DATA COIL SPECIFICATIONS ORDER NUMBER Nominal Coil VDC 5 Max. Continuous VDC 8.4 Coil Resistance ± 10% 125 Must Operate VDC 3.5 SCO Contact AZ695–5 SCO with Gold Plating Contact AZ695–5G 6 10.1 180 4.2 AZ695–6 AZ695–6G 9 15.2 405 6.3 AZ695–9 AZ695–9G 12 20.2 720 8.4 AZ695–12 AZ695–12G 18 29.5 1,620 12.6 AZ695–18 AZ695–18G 24 40.5 2,880 16.8 AZ695–24 AZ695–24G MECHANICAL DATA .012 (0.3) .690 (17.5) .012 (0.3) .256 (6.5) .492 (12.5) 0.13 (3.3) .032 (0.8) .012 (0.3) .020 (0.5) 0.2 (5.08) 0.3 (7.62) 0.1 (2.54) .035 (0.9) 0.2 (5.08) PC BOARD LAYOUT WIRING DIAGRAM .043 (1.1) DIA 13 0.2 (5.08) 0.2 (5.08) 0.3 (7.62) 0.1 (2.54) Viewed toward terminals 7 5 1 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 7/12/01W