JEWEL HILL ELECTRONIC CO.,LTD. JEWEL HILL ELECTRONIC CO.,LTD. SPECIFICATIONS FOR LCD MODULE GG2048 Module No. Office Address: Rm. 518,5/F., 101 Shangbu Industrial District, HuaqiangNorthRoad, Shenzhen, China TEL : (86)-755-83362489 83617492 FAX: (86)-755-83286396 83365871 E-mail: [email protected] [email protected] Website: GG2048 www.jewelhillelectronic.com VER: 2.0 -0- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. TABLE OF CONTENTS LCM NUMBER SYSTEM ..................................................................... 2 1. GENERAL DESCRIPTION ........................................................... 3 2. FEATURES...................................................................................... 3 3. MECHANICAL SPECIFICATION .............................................. 3 4. MECHANICAL DIMENSION ....................................................... 4 5. MAXIMUM RATINGS .................................................................. 5 6. ELECTRICAL CHARACTERISTICS ......................................... 5 7. MODULE FUNCTION DESCRIPTION ...................................... 6 8. ELECTRO-OPTICAL CHARACTERISTICS .......................... 14 9. RELIABILITY............................................................................... 18 10. PRECAUTIONS FOR USING LCD MODULES ...................... 19 11. USING LCD MODULES .............................................................. 21 12. REVISION HISTORY .................................................................. 23 SAMPLE APPROVED REPORT ....................................................... 24 GG2048 VER: 2.0 -1- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. LCM Number System GG 2048 F W D S P F N F-V00-L Y C X OTHER C: WITH CONTROLLER N: WITHOUT CONTROLLER; BACKLIGHT COLOR: A: AMBER; B: BLUE; W: WHITE; Y: YELLOW-GREEN R: RED; O: THER COLOR BACKLIGHT MODE: L: LED; E: EL; C: CCFL; N: WITHOUT BACKLIGHT VERSION NUMBER: V00~V99 CONNECTOR: P: PIN; H: HEATSEAL; Z: ZEBRA; F: FPC; O: OTHER SILK-SCREEN N: WIHTOUT SILK-SCREEN; S: WITH SILK-SCREEN POLARIZER TYPE: R: REFLECTIVE; T:TRANSMISSIVE F: TRANSFLECTIVE; OTHER LCD DISPLAY MODE: P: POSITIVE; N: NEGATIVE TEMPERATURE RANGE: N: NORMAL TEMPERATURE RANGE M: MIDDLE TEMPERATURE RANGE W: WIDE TEMPERATURE RANGE S: SUPER WIDE TEMPERATURE RANGE VIEWING DIRECTION: U: UPPER(12:00); D: DOWN(6:00) L: LEFT(9:00); R: RIGHT(3:00) LCD COLOR MODE: W: BLACK-WHITE; Y: YELLOW-GREEN G: GRAY; B: BLUE; O: OTHER LCD TYPE: T: TN; H: HTN; S: STN; F: FSTN; C: CSTN; D: TFT SERIAL NUMBER:0000~9999 PRODUCE GP: LCD GT: TAB GF: COF GG2048 VER: 2.0 -2- TYPE: PANEL; GC: COLOR STN; LCM; GG: COG LCM; & TFT LCM Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 1. GENERAL DESCRIPTION The GG2048 is a 128 x 32 Dots+Icon Graphic LCD module. It has a FSTN panel composed of 128 segments and 33 commons. The LCM can be easily accessed by microcontroller via parallel or series interface. 2. FEATURES Display Mode Display Format Input Data Transflective and positive FSTN module Graphic 128x32 dots+Icon 8 bit parallel or Serial data input from MPU (Selection with PCB) Multiplexing Ratio 1/65 Duty Bias 1/9 Bias Viewing Direction 6 O’clock Controller LSI SSD1815 Backlight LED/Y-G 3. MECHANICAL SPECIFICATION GG2048 Item Specifications Unit Dimensional outline 117.6 x (31.2+24.0) x 10.0(max) mm Resolution 128segs x 32coms+Icon dots Active area Reference the Drawing in page4 mm Dots pitch Reference the Drawing in page4 mm Dots size Reference the Drawing in page4 mm VER: 2.0 -3- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 4. MECHANICAL DIMENSION GG2048 VER: 2.0 -4- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 5. MAXIMUM RATINGS Item Symbol Min Max Unit VDD - Vss -0.3 4.0 V VLCD -0.3 18.0 V Input Voltage VIN -0.3 VDD+0.3 Operating temperature TOPR -20 +70 V ℃ Storage temperature TSTR -30 +80 ℃ --- --- 90 %RH Supply voltage Humidity Note 6. ELECTRICAL CHARACTERISTICS Item Supply Voltage Input Voltage Symbol Condition Min. Typ. Max. Unit Logic VDD --- --- 3.0 --- V H level VIH 0.8VDD --- VDD L level VIL VSS --- 0.2VDD Current Consumption (LCD DRIVER) LCD Driving Voltage Current Consumption (WITH LED) GG2048 VER: 2.0 --- V VDD=3.0V; IDD VLCD=9.3V,Tamb=25℃; --- --- 2.0 mA VLCD Bias=1/7 VLCD=V0-VSS --- 9.3 --- V --- --- TBD mA VDD=3.0V; ILED VLED=8.7V,Tamb=25℃; -5- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 7. MODULE FUNCTION DESCRIPTION 7.1. PIN DESCRIPTION Pin No. Symbol 1 /CS1 Chip Selection 2 /RES Reset Signal Input 3 D/C Date/Command Register Selection 4 NC/WR 5 Description No Connect(Serial Interface)/Write Signal(parallel Interface) NC/E_RD No Connect(Serial Interface)/Read Signal(parallel Interface) 6 7 8 NC/DB0 NC/DB1 NC/DB2 9 NC/DB3 10 NC/DB4 11 NC/DB5 12 SCL/DB6 Serial Colok Input/Data Bus with bit6 for Parallel Interface 13 SDA/DB7 Serial Data Input/Data Bus with bit7 for Parallel Interface No Connect(Serial Interface)/Data Bus Low 5-bit(parallel Interface) 14 VDD 15 NC No Connect 16 VSS Power Supply for Ground 17 NC/VR 18 LED+ 19 NC 20 LED- GG2048 VER: 2.0 Power Supply for Positive No Connect/External Resistor Regulator Terminal Power Supply for LED Positive No Connect Power Supply for LED Negative -6- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 7.2 TIMING CHARACTERISTICS 1.SYSTEM BUS READ/WRITE CHARACTERISTIC GG2048 VER: 2.0 -7- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. GG2048 VER: 2.0 -8- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. GG2048 VER: 2.0 -9- Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 7.3 BLOCK CIRCUIT 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 /CS /RES D/C R/W E_RD D0 D1 D2 D3 D4 D5 D6 D7 VDD VSS VEE C3N C1P C1N C2N C2P VL2 VL3 VL4 VL5 VL6 VF VSS C86 PS VDD /HPM VSS IRS CON2 2048CON34 C10 J7 E_RD R3 CON1 2048CON20 CS RES D/C NC(RW) NC(E_RD) NC(D0) NC(D1) NC(D2) NC(D3) NC(D4) NC(D5) SCL(D6) SDA(D7) VDD NC VSS NC(VR) LED+ VC LEDLED1 J6 R/W C4 J8 D0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 C3 J9 D1 J2 J3 J4 J5 C86 PS /HPM IRS C9 R2 C2 C8 J10 D2 C1 C7 C6 J1 R1 C5 J11 D3 R4 J12 D4 R5 R6 J13 D5 R7 GG2048 VER: 2.0 - 10 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 7.4 TABLE OF COMMAND GG2048 VER: 2.0 - 11 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. GG2048 VER: 2.0 - 12 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. GG2048 VER: 2.0 - 13 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 8. ELECTRO-OPTICAL CHARACTERISTICS Item Symbol LCD driving Condition θ=ψ= 0 VLCD voltage Rise Time (Tr) Temp Min Typ. Max 0℃ --- 9.5 --- 25℃ 9.0 9.3 9.6 50℃ --- 9.1 --- --- --- -- --- ---- --- --- 225 340 --- 240 360 --- --- -- --- --- -- 5 10 --- 0℃ Decay Time (Tf) Response Time Rise Time (Tr) Decay Time (Tf) θ=ψ= 0 Rise Time (Tr) 25℃ 50℃ Decay Time (Tf) Contrast Ratio Viewing Angle Range θ(25℃) Cr θ=ψ= 0 25℃ θ(ψ= 0°) ψ= 90° ψ=180° ψ=270° (6”) (3”) (12”) (9”) 45 35 15 30 CR≥2 Units Note V NOTE1 msec --- NOTE2 NOTE4 備註 Deg NOTE3 z For panel only GG2048 VER: 2.0 - 14 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. ․Electro-Optical Characteristics Measuring Equipment(DMS501) Printer Detector Positioning (θ,φ) Display Driver LCD Temperature Control System GG2048 VER: 2.0 Illumination (D65) - 15 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. ․Note 1. Definition of Driving Voltage( Vlcd) : Selected Waveform 100 % 30 % 50 % Non-Selected Waveform 50 % Vth2 Vth1 Operation Voltage Vlcd ․Note 2. Definition of Optical Response Time : NO SEL ECTED W AV EFORM (1 0S EC) SEL ECTED WA VEFORM (1 0S EC) NO SEL ECTED W AV EFORM (1 0S EC) 1 0% 10 0 % 9 0% 10 0 % Brig htn ess Tr Tf Rise Tim e Fall Tim e t GG2048 VER: 2.0 - 16 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. ․Note 3. Definition of Viewing Angle θ and ψ : Normal : θ=0° 12 O’clock Direction φ=180° θ φ=90° φ=270° 9 O’clock Direction 3 O’clock Direction φ φ=0° Viewing Direction 6 O’clock Direction ․Note 4. Definition of Contrast ratio( CR) : Brightness (%) CR = Brightness of Non-selected Segment (B2) Brightness of Selected Segment (B1) Brightness Curve for Selected Segment 100% 0% B2 Brightness Curve for Non-selected Segment CR,max B1 Driving Voltage V,max GG2048 VER: 2.0 Contrast - 17 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 9. RELIABILITY 9.1. MTBF The LCD module shall be designed to meet a minimum MTBF value of 50000 hours with normal. (25°C in the room without sunlight) 9.2. TESTS NO. ITEM CONDITION CRITERION 。No Defect Of 1 High Temperature Operating 70℃ 120Hrs Operational Function In Room Temperature Are Allowable. 2 Low Temperature Operating -20℃ 120Hrs 。IDD of LCM in 3 High Temperature/ Humidity Non-Operating 70℃ ,90%RH ,120 Hrs 4 High Temperature Non-Operating 80℃ 120Hrs 5 Low Temperature Non-Operating -30℃ 120Hrs 6 Temperature Cycling Non-Operating Pre-and post-test should follow specification -20℃(30Min )↔ 60℃(30Min) 10 CYCLES Notes: Judgments should be mode after exposure in room temperature for two hours. GG2048 VER: 2.0 - 18 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 10. PRECAUTIONS FOR USING LCD MODULES 10.1. HANDLING PRECAUTIONS (1) The display panel is made of glass. Do not subject it to a mechanical shock or impact by dropping it. (2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water. (3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. (4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. (5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily contaminated, moisten a cloth with one of the following solvents: - Isopropyl alcohol - Ethyl alcohol (6) Solvents other than those above mentioned may damage the polarizer. Especially, do not use the following: - Water - Ketone - Aromatic solvents (7) Extra care to minimize corrosion of the electrode. Water droplets, moisture condensation or a current flow in a high-humidity environment accelerates corrosion of the electrode. (8) Install the LCD Module by using the mounting holes. When mounting the LCD Module, make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable. (9) (10) (11) (12) Do not attempt to disassemble or process the LCD Module. NC terminal should be open. Do not connect anything. If the logic circuit power is off, do not apply the input signals. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. - Be sure to ground the body when handling he LCD Module. - Tools required for assembling, such as soldering irons, must be properly grounded. -To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. GG2048 VER: 2.0 - 19 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. -The LCD Module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated. 10.2. STORAGE CONDITIONS When storing, avoid the LCD module to be exposed to direct sunlight of fluorescent lamps. For stability, to keep it away form high temperature and high humidity environment (The best condition is : 23±5°C, 45±20%RH). ESD protection is necessary for long-term storage also. 10.3. OTHERS Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature. If the LCD Module have been operating for a long time showing the same display patterns the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be recovered by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability. To minimize the performance degradation of the LCD Module resulting from destruction caused by static electricity etc. exercise care to avoid holding the following sections when handling the modules. - Exposed area of the printed circuit board. - Terminal electrode sections. GG2048 VER: 2.0 - 20 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 11. Using LCD modules 11.1 LIQUID CRYSTAL DISPLAY MODULES LCD is composed of glass and polarizer. Pay attention to the following items when handling. (1) Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation or polarizer peel-off may occur with high temperature and high humidity. (2) Do not touch, push or rub the exposed polarizers with anything harder than a HB pencil lead (glass, tweezers, etc). (3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of organic substances, which will be damaged by chemicals such as acetone, toluene, toluene, ethanol and isopropyl alcohol. (4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois soaked in petroleum ether. Do not scrub hard to avoid damaging the display surface. (5) Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. (6) Avoid contacting oil and fats. (7) Condensation on the surface and contact with terminals due to cold will damage, stain or polarizers. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air. (8) Do not put or attach anything on the display area to avoid leaving marks on. (9) Do not touch the display with bare hands. This will stain the display area and degrade insulation between terminals (some cosmetics are determinate to the polarizers). (10)As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. 11.2 INSTALLING LCD MODULE Attend to the following items when installing the LCM. (1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell. (2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be ±0.1mm. 11.3 ELECTRO-STATIC DISCHARGE CONTROL Since this module uses a CMOS LSI, the same careful attention should be paid for electrostatic discharge as for an ordinary CMOS IC. GG2048 VER: 2.0 - 21 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. (1) Make certain that you are grounded when handing LCM. (2) Before removing LCM from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. (3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak. (4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. (5) As far as possible, make the electric potential of your work clothes and that of the workbenches to the ground potential. (6) To reduce the generation of electro-static discharge, be careful that the air in the work is not too dried. A relative humidity of 50%-60% is recommended. 11.4 PRECAUTIONS FOR OPERATION (1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to show the best contrast. (2) Driving the LCD in the voltage above the limit will shorten its lifetime. (3) Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature range. (4) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is turned off and then on. (5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, this product must be used and stored within the specified condition of 23±5°C, 45±20%RH. (6) When turning the power on, input each signal after the positive/negative voltage becomes stable. 11.5 SAFETY (1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. (2) If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water. GG2048 VER: 2.0 - 22 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. 12. REVISION HISTORY Version Revise record Date 1.0 Original version 05-01-01 2.0 Change specification format 05-11-21 GG2048 VER: 2.0 - 23 - Issue date: 2005/11/21 JEWEL HILL ELECTRONIC CO.,LTD. SAMPLE APPROVED REPORT (样品确认单) SAMPLE MODEL NO. (样品型号) GG2048 SAMPLE SERIES NUMBER NO. (样品序号) SAMPLE QUANTITY (样品数量) COLOR/TYPE (底色/类型) FSTN/POSITIVE VIEWING DIRECTION (视角) 6:00 DRIVING METHOD (驱动参数) 1/33Duty, 1/7Bias LOGIC VOLTAGE (IC 工作电压) 3.0V LCD VOP (LCD 驱动电压) 9.3V OPERATING TEMP. (操作温度) ℃ -20~70 STORAGE TEMP. (储存温度) ℃ -30~80 POLARIZER----FRONT (首偏光片) TRANSMISSIVE POLARIZER----BACK (后偏光片) TRANSFLECTIVE CONTROLLER/DRIVER IC(控制/驱动 IC) SSD1815 BACKLIGHT COLOR/TYPE (背光源类型/颜色) LED/Y-G DRAWING REV/NO./QUANTITY (图纸版本/数量) SPECIFICATION (规格书 份数) REMARKS： (备注) WRIT BY：_________ DATE：_________ APROV BY：_________ DATE：________ CUSTOMER’S APPROVAL (客户确认)： 1） FUNCTION （功能）： OK N.G. 2） DRIVER CONDITION （驱动条件）： OK N.G. 3） DISPLAY MODE （显示模式）： OK N.G. 4） VIEWING ANGLE （视角）： OK N.G. 5） BACKLIGHT （背光源）： OK N.G. 6） DISPLAYING PATTERN （显示效果）： OK N.G. CUSTOMER’S CONCLUSIONS (客户意见)：______________________________________ _______________________________________________________________________________ ________________________________________ CUSTOMER’S SIGNATURE（客户签名）：_____________ DATE (日期)：___________ GG2048 VER: 2.0 - 24 - Issue date: 2005/11/21