Data Sheet 0635E CRYSTAL OSCILLATORS OF-X8HXXXXX Series Precision SC-cut OCXO in 25x22 mm Low Profile SMD Package Product Data Sheet Features • • SC-cut crystal -9 High Stability (up to ± 5x10 ) • • • • Low Aging (5x10 /day, 5x10 /year) Low Phase Noise (-160 dBc/Hz, TYP, floor) Sine Wave or HCMOS/TTL output 4.8 MHz to 160 MHz Frequencies Available -10 1.0 (25,4 mm) -8 1 5 0.87 (22,0 mm) 2 Applications 3 4 • Specifications: Telecommunication Systems • • • Data Communications GPS Instrumentation 0.41 (10.5 mm) 0.1 (2,5 mm) Vcc 3 4 0.1 (2,5 mm) A 0.70 (17,8 mm) Vc 1 Vref 2 2 3 DUT B 4 OUTPUT 0.2 (5 mm) 1 5 5 10K 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com Data Sheet 0635E CRYSTAL OSCILLATORS OF-X8HXXXXX Series Aging ∆F/F After Reflow Allan Variance SSB Phase Noise ∆F/F Retrace G-sensitivity Input Voltage Vcc Min Max Unit -0.5 13.0 V -40 -1 85 9 °C V 160 MHz ppb ppb/V 4.8 vs. Temp. vs. Supply per day per year Per profile below .1s to 10s 1Hz 10 Hz 100 Hz 1 KHz 10 KHz After 30 minutes worst direction 4.75 3.15 11.4 Typ 10.000 ±10 1 5E-10 1E-7 0.1 1E-11 -90 -120 -150 -153 -160 5.0 3.3 12.0 0.8 1.5 2.5 -50 2 0.2 ±10 ±1.0 5.25 3.45 12.6 1.2 Note 1* See chart below ppm after 30 days 5E-8 available2* Each time dBc/Hz 3* ppb ppb/G V See chart below to specify steady state, 25°C W Standard Operating steady state, -30°C Temperature, for Op start-up @ -30°C 3.2 Temp. 85 °C ad 20% Subharmonics -45 dBc At Higher Frequencies Spectral Purity Spurious -80 Harmonics/Sine -35 -30 10KOhm//15pF (HCMOS/TTL), 50 Ohm (Sinewave) Load to 0.1ppm accuracy 3 5 minutes 3 min. at 12V Warm-up time τ 3.3V HCMOS/TTL compatible or Sinewave (+7± 3) dBm -25dBm Harmonics at sine Output Waveform Vc 0 4.0 V Control voltage from nominal F ±0.5 ±1 ppm Pull range Monotonic, posit 0.4 ppm/V Deviation slope Vc0 @25°C, Fnom. 1.0 2.0 3.0 V Setability Environmental and Mechanical -30°C to 70°C Standard, Other options – see chart below Operating temp. range Per MIL-STD-202, 30G, 11ms Mechanical Shock Per MIL-STD-202, 5G to 2000 Hz Vibration See MAX reflow profile below Soldering Conditions Electrical Connections Pin #1-Vc ; Pin#2 – Vref; Pin #3 – Vcc; Pin #4- Output ; Pin #5- GND; 4* Pin Out Power consumption P Condition All parameters for 10 MHz Parameter Symb Absolute Maximum Ratings Vcc Input Break Down Voltage Ts Storage temper. Vc Control Voltage Electrical F Frequency Frequency stability ∆F/F Notes: 1* Higher frequencies can be achieved either by using higher frequency crystals or by low noise analog harmonic multiplication. Both methods have advantages and drawbacks. If lowest possible phase noise on the noise floor is most important – high frequency crystal will be used. If phase noise close to the carrier and aging are more important – multiplication will be used. Please consult factory for your specific requirement. 2* Aging rate is usually proportional to the operating frequency, unless higher frequency is achieved by multiplication. Keep it in mind while specifying aging. 3* Phase noise deteriorates with frequencies going higher. If analog multiplication is used to achieve higher frequency the phase noise roughly follows the formula of additional 20LogN, where N is a multiplication factor across entire frequency offset range. If higher frequency is achieved by using higher frequency crystal phase noise close to the carrier deteriorates due to the lower Q of the crystal and is usually worse, compared to multiplied solution. On the noise floor, however it remains more or less the same. This design usually starts utilizing multiplication techniques in the range of 25 MHz to 35 MHz. 4* Pads “A” and “B” may or may not appear on the actual package. They can be used when additional functions i.e. “Oven Ready” alarm or “Tristate” are specified. Please consult factory. 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com Data Sheet 0635E CRYSTAL OSCILLATORS OF-X8HXXXXX Series Creating a Part Number OF - X 8H X XX X X Aging Package Code OF 5 pad 25x22mm SMD Code L S P Supply Voltage Code 0 A F Specification 5V ± 5% 3.3V± 5% 12V 5% Output Code T S Specification TTL Sinewave Temperature Stability Code 17 58 28 18 59 YZ Specification 1x10-9/Day 5x10-10/Day 2x10-10/Day Temperature Range Specification 1x10-7 5x10-8 2x10-8 1x10-8 5x10-9 Yx10-Z Code A B C D E F Specification 0°C to 50°C -10°C to 60°C 0°C to 70°C -20°C to 70°C -30°C to 70°C -40°C to 80°C Not all combinations are available. Consult Factory. MAX Reflow Profile 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com