plerowTM ALN2045M3 Internally Matched LNA Module Features Description · S21 = 36.4 dB @ 1920 MHz = 35.6 dB @ 2170 MHz · NF of 0.7 dB over Frequency · Unconditionally Stable · Single 5V Supply · High OIP3 @ Low Current The plerowTM ALN-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communication terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface-mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Specifications (in Production) Typ. @ T = 25°C, Vs = 5 V, Freq. = 2045 MHz, Zo.sys = 50 ohm Parameter Frequency Range Unit Min MHz 1920 Gain dB 35 Gain Flatness dB Noise Figure (NF) Output IP3 S11 / S22 (1) dB dBm (2) 3-stage Single Type Specifications 43 Typ Max 2170 36 ± 0.4 ± 0.5 0.70 0.75 More Information Website: www.asb.co.kr E-mail: [email protected] 44 DB Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 -18 / -10 Output P1dB dBm 28 29 Switching Time µsec - Supply Current mA 400 Supply Voltage V 5 Impedance Ω 50 ASB Inc., 4th Fl. Venture Town Bldg., 367-17 Goijeong-Dong, Seo-Gu, Daejon 302-716, Korea 430 Max. RF Input Power dBm C.W 29 ~ 31 (before fail) Package Type & Size mm Surface Mount Type, 25Wx13Lx3.8H Operating temperature is -40°C to +85°C. 1) OIP3 is measured with two tones at an output power of +12 dBm / tone separated by 1 MHz. 2) S11/S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to Vs. Outline Drawing (Unit: mm) plerow ALN2045M3 (Top View) Pin Number Function 3 RF In 8 RF Out 10 Vs Others Ground (Bottom View) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins for better RF and thermal performance, as shown in the drawing at the left side. Solder Stencil Area (Side View) Ø0.4 plated thru holes to ground plane 1/3 (Recommended Footprint) www.asb.co.kr March 2009 plerowTM ALN2045M3 Internally Matched LNA Module S-parameters Typical Performance (Measured) 1920~2170 +5 V Stability Factor (K) Noise Figure OIP3 2/3 P1dB www.asb.co.kr March 2009 plerowTM ALN2045M3 Internally Matched LNA Module Application Circuit VS + - Tantal or MLC (Multi Layer Ceramic) Capacitor C1 C2 ALN IN OUT 1) The tantal or MLC (Multi Layer Ceramic) capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. The capacitor should be placed as close as possible to Vs pin and be connected directly to the ground plane for the best electrical performance. 2) DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are included inside the ALN module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is determined by considering the application frequency. Evaluation Board Layout Recommended Soldering Reflow Process Vs 20~40 sec 260°C Ramp-up (3˚C/sec) 200°C Ramp-down (6°C/sec) OUT IN 150°C 60~180 sec 3/3 Size 40x40mm (for ALN-M3 Series – 25x13mm) www.asb.co.kr March 2009