Pressure Freescale Semiconductor + MPX2102 Rev 7, 10/2008 100 kPa On-Chip Temperature Compensated Silicon Pressure Sensors MPX2102 Series 0 to 100 kPa (0 to 14.5 psi) 40 mV Full Scale (Typical) The MPX2102 series devices are silicon piezoresistive pressure sensors providing a highly accurate and linear voltage output directly proportional to the applied pressure. The sensor is a single, monolithic silicon diaphragm with the strain gauge and a thin-film resistor network integrated on-chip. The chip is laser trimmed for precise span and offset calibration and temperature compensation. Application Examples • • • • • • • Features • • • • Temperature Compensated Over 0°C to +85°C Easy-to-Use Chip Carrier Package Options Available in Absolute, Differential and Gauge Configurations Absolute, Differential and Gauge Options Pump/Motor Control Robotics Level Detectors Medical Diagnostics Pressure Switching Barometers Altimeters ORDERING INFORMATION Package Device Name Options Unibody Package (MPX2102 Series) MPX2102A Tray MPX2102DP Tray Case No. None 344 • MPX2102AP Tray 344B MPX2102GP Tray 344B MPX2102ASX Tray 344F Tray 344D Small Outline Package (MPXV2102G Series) MPXV2102GP Tray 1369 MPAK Package (MPXM2102 Series) MPXM2102A Rail 1320 MPXM2102AT1 Tape and Reel 1320 MPXM2102GST1 MPXM2102AS MPXM2102AST1 Rail 1320A Tape and Reel 1320A Rail 1320A Tape and Reel 1320A Dual Gauge Pressure Type Differential Absolute • • 344C • • • • MPX2102GVP MPXM2102GS # of Ports Single • • • MPX2102AP MPX2102GP • MPX2102A • MPX2102GVP • MPXV2102GP • • © Freescale Semiconductor, Inc., 2005-2008. All rights reserved. MPX2102A MPX2102DP • • • • • • • Device Marking • • MPXM2102A MPXM2102A MPXM2102GS MPXM2102GS • • MPXM2102AS MPXM2102AS Pressure UNIBODY PACKAGES MPX2102A CASE 344-15 MPX2102AP/GP CASE 344B-01 MPX2102DP CASE 344C-01 MPX2102GVP CASE 344D-01 MPAK SMALL OUTLINE PACKAGES MPXV2102GP CASE 1369-01 MPX2102ASX CASE 344F-01 MPXM2102A CASE 1320-02 MPXM2102GS/AS CASE 1320A-02 MPX2102 2 Sensors Freescale Semiconductor Pressure Operating Characteristics Table 1. Operating Characteristics (VS = 10 VDC, TA = 25°C unless otherwise noted, P1 > P2) Characteristic Symbol Min Typ Max Units POP 0 — 100 kPa Supply Voltage(2) VS — 10 16 VDC Supply Current IO — 6.0 — mAdc VFSS 38.5 40 41.5 mV VOFF -1.0 -2.0 -1.0 -2.0 — — — — 1.0 2.0 1.0 2.0 mV ΔV/ΔΡ — 0.4 — mV/kPa — — — — -0.6 -1.0 -0.6 -1.0 — — — — 0.4 1.0 0.4 1.0 %VFSS Pressure Hysteresis(5) (0 to 100 kPa) — — ±0.1 — %VFSS Temperature Hysteresis(5)(- 40°C to +125°C) — — ±0.5 — %VFSS Temperature Coefficient of Full Scale Span(5) TCVFSS -2.0 — 2.0 %VFSS Temperature Coefficient of Offset(5) TCVOFF -1.0 — 1.0 mV ZIN 1000 — 2500 W ZOUT 1400 — 3000 W Response Time(6) (10% to 90%) tR — 1.0 — ms Warm-Up Time — — 20 — ms Offset Stability(7) — — ±0.5 — %VFSS Differential Pressure Range(1) Full Scale Span(3) Offset(4) MPX2102D Series MPX2102A Series MPXM2102D/G Series MPXM2102A Series Sensitivity VOFF mV Linearity(5) MPX2102D Series MPX2102A Series MPXM2102D/G Series MPXM2102A Series Input Impedance Output Impedance %VFSS 1. 1.0 kPa (kiloPascal) equals 0.145 psi. 2. Device is ratiometric within this specified excitation range. Operating the device above the specified excitation range may induce additional error due to device self-heating. 3. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum related pressure. 4. Offset (VOFF) is defined as the output voltage at the minimum rated pressure. 5. Accuracy (error budget) consists of the following: • Linearity: • • • • Output deviation from a straight line relationship with pressure, using end point method, over the specified pressure range. Temperature Hysteresis:Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. Pressure Hysteresis: Output deviation at any pressure with the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure at 25°C. TcSpan: Output deviation at full rated pressure over the temperature range of 0 to 85°C, relative to 25°C. TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85°C, relative to 25°C. 6. Response Time is defined as the time from the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 7. Offset stability is the product’s output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test. MPX2102 Sensors Freescale Semiconductor 3 Pressure Maximum Ratings Table 2. Maximum Ratings(1) Rating Symbol Value Unit Maximum Pressure (P1 > P2) PMAX 400 kPa Storage Temperature TSTG -40 to +125 °C TA -40 to +125 °C Operating Temperature 1. Exposure beyond the specified limits may cause permanent damage or degradation to the device. Voltage Output versus Applied Differential The differential voltage output of the sensor is directly proportional to the differential pressure applied. The absolute sensor has a built-in reference vacuum. The output voltage will decrease as vacuum, relative to ambient, is drawn on the pressure (P1) side. The output voltage of the differential or gauge sensor increases with increasing pressure applied to the pressure (P1) side relative to the vacuum (P2) side. Similarly, output voltage increases as increasing vacuum is applied to the vacuum (P2) side relative to the pressure (P1) side. Figure 1 illustrates a block diagram of the internal circuitry on the stand-alone pressure sensor chip. VS 3 Thin Film Temperature Compensation and Calibration Circuitry X-ducer Sensing Element 2 +V OUT 4 -V OUT 1 GND Figure 1. Temperature Compensated Pressure Sensor Schematic MPX2102 4 Sensors Freescale Semiconductor Pressure On-Chip Temperature Compensation and Calibration Figure 2 shows the output characteristics of the MPX2102 series at 25°C. The output is directly proportional to the differential pressure and is essentially a straight line. VS = 10 VDC TA = 25°C MPX2102 P1 > P2 40 35 30 The effects of temperature on Full Scale Span and Offset are very small and are shown under Operating Characteristics. TYP Output (mVDC) 25 20 Span Range (TYP) MAX 15 MIN 10 5 0 kPa PSI -5 0 25 3.62 50 7.25 100 75 10.88 14.5 Offset (TYP) Figure 2. Output vs. Pressure Differential Silicone Gel Die Coat Differential/Gauge Die P1 Epoxy Case Wire Bond Lead Frame Silicone Gel Die Coat Stainless Steel Metal Cover Differential/GaugeElement P2 Bond Die Absolute Die P1 Stainless Steel Metal Cover Epoxy Case Wire Bond Lead Frame Die Bond Absolute Element P2 Figure 3. Cross Sectional Diagrams (Not to Scale) LINEARITY Linearity refers to how well a transducer's output follows the equation: VOUT = VOFF + sensitivity x P over the operating pressure range. There are two basic methods for calculating nonlinearity: (1) end point straight line fit (see Figure 4) or (2) a least squares best line fit. While a least squares fit gives the “best case” linearity error (lower numerical value), the calculations required are burdensome. Conversely, an end point fit will give the “worst case” error (often more desirable in error budget calculations) and the calculations are more straightforward for the user. Freescale’s specified pressure sensor linearities are based on the end point straight line method measured at the midrange pressure. Least Squares Fit Least Square Deviation Exaggerated Performance Curve Relative Voltage Output Figure 3 illustrates the absolute sensing configuration (right) and the differential or gauge configuration in the basic chip carrier (Case 344). A silicone gel isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MPX2102 series pressure sensor operating characteristics and internal reliability and qualification tests are based on use of dry air as the pressure media. Media other than dry air may have adverse effects on sensor performance and long term reliability. Contact the factory for information regarding media compatibility in your application. Straight Line Deviation End Point Straight Line Fit Offset 0 50 Pressure (% Full scale) 100 Figure 4. Linearity Specification Comparison MPX2102 Sensors Freescale Semiconductor 5 Pressure PRESSURE (P1)/VACUUM (P2) SIDE IDENTIFICATION TABLE Freescale designates the two sides of the pressure sensor as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing the silicone gel which isolates the die. The differential or gauge sensor is designed to operate with positive differential pressure applied, P1 > P2. The absolute sensor is designed for vacuum applied to P1 side. The Pressure (P1) side may be identified by using Table 3. Table 3. Pressure (P1) Side Delineation Part Number MPX2102A Case Type 344 Pressure (P1) Side Identifier Stainless Steel Cap MPX2102DP 344C Side with Part Marking MPX2102AP, MPX2102GP 344B Side with Port Attached MPX2102GVP 344D Stainless Steel Cap MPX2102ASX 344F Side with Port Marking MPXV2102GP 1369 Side with Port Attached MPXM2102A, MPX2102ATI 1320 Stainless Steel Cap MPXM2102AS, MPXM2102GS, MPXM2102ASTI, MPXM2102GSTI 1320A Side with Port Attached MPX2102 6 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS C R M 1 B 2 -A- 3 Z 4 DIM A B C D F G J L M N R Y Z N L 1 2 3 4 PIN 1 -TSEATING PLANE J F G F Y D 4 PL 0.136 (0.005) STYLE 1: PIN 1. 2. 3. 4. M T A DAMBAR TRIM ZONE: THIS IS INCLUDED WITHIN DIM. "F" 8 PL M STYLE 2: PIN 1. 2. 3. 4. GROUND + OUTPUT + SUPPLY - OUTPUT STYLE 3: PIN 1. 2. 3. 4. VCC - SUPPLY + SUPPLY GROUND NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION -A- IS INCLUSIVE OF THE MOLD STOP RING. MOLD STOP RING NOT TO EXCEED 16.00 (0.630). INCHES MILLIMETERS MIN MAX MIN MAX 0.595 0.630 15.11 16.00 0.514 0.534 13.06 13.56 0.200 0.220 5.08 5.59 0.016 0.020 0.41 0.51 0.048 0.064 1.22 1.63 0.100 BSC 2.54 BSC 0.014 0.016 0.36 0.40 0.695 0.725 17.65 18.42 30˚ NOM 30˚ NOM 0.475 0.495 12.07 12.57 0.430 0.450 10.92 11.43 0.048 0.052 1.22 1.32 0.106 0.118 2.68 3.00 GND -VOUT VS +VOUT CASE 344-15 ISSUE AA UNIBODY PACKAGE SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -A- -T- U L R H N PORT #1 POSITIVE PRESSURE (P1) -Q- B 1 2 3 4 PIN 1 K -P0.25 (0.010) J M T Q S S F C G D 4 PL 0.13 (0.005) M T S S Q S DIM A B C D F G H J K L N P Q R S U INCHES MILLIMETERS MIN MAX MIN MAX 1.145 1.175 29.08 29.85 0.685 0.715 17.40 18.16 0.305 0.325 7.75 8.26 0.016 0.020 0.41 0.51 0.048 0.064 1.22 1.63 0.100 BSC 2.54 BSC 0.182 0.194 4.62 4.93 0.014 0.016 0.36 0.41 0.695 0.725 17.65 18.42 0.290 0.300 7.37 7.62 0.420 0.440 10.67 11.18 0.153 0.159 3.89 4.04 0.153 0.159 3.89 4.04 0.230 0.250 5.84 6.35 0.220 0.240 5.59 6.10 0.910 BSC 23.11 BSC STYLE 1: PIN 1. GROUND 2. + OUTPUT 3. + SUPPLY 4. - OUTPUT CASE 344B-01 ISSUE B UNIBODY PACKAGE MPX2102 7 Sensors Freescale Semiconductor Pressure 16 PACKAGE DIMENSIONS NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -AU V PORT #1 R W L H PORT #2 N DIM A B C D F G H J K L N P Q R S U V W PORT #1 POSITIVE PRESSURE (P1) PORT #2 VACUUM (P2) -QB SEATING PLANE SEATING PLANE 1 2 3 4 PIN 1 K -P-T- -T- 0.25 (0.010) M T Q S S F J G D 4 PL C 0.13 (0.005) T S M S Q S INCHES MILLIMETERS MIN MAX MIN MAX 1.145 1.175 29.08 29.85 0.685 0.715 17.40 18.16 0.405 0.435 10.29 11.05 0.016 0.020 0.41 0.51 0.048 0.064 1.22 1.63 0.100 BSC 2.54 BSC 0.182 0.194 4.62 4.93 0.014 0.016 0.36 0.41 0.695 0.725 17.65 18.42 0.290 0.300 7.37 7.62 0.420 0.440 10.67 11.18 0.153 0.159 3.89 4.04 0.153 0.159 3.89 4.04 0.063 0.083 1.60 2.11 0.220 0.240 5.59 6.10 0.910 BSC 23.11 BSC 0.248 0.278 6.30 7.06 0.310 0.330 7.87 8.38 STYLE 1: PIN 1. 2. 3. 4. GROUND + OUTPUT + SUPPLY - OUTPUT CASE 344C-01 ISSUE B UNIBODY PACKAGE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. -AU SEATING PLANE -T- L H PORT #2 VACUUM (P2) R DIM A B C D F G H J K L N P Q R S U POSITIVE PRESSURE (P1) N -Q- B 1 2 3 4 K PIN 1 S C F -P- J 0.25 (0.010) M T Q S G D 4 PL 0.13 (0.005) M T S S Q S STYLE 1: PIN 1. 2. 3. 4. INCHES MILLIMETERS MIN MAX MIN MAX 1.145 1.175 29.08 29.85 0.685 0.715 17.40 18.16 0.305 0.325 7.75 8.26 0.016 0.020 0.41 0.51 0.048 0.064 1.22 1.63 0.100 BSC 2.54 BSC 0.182 0.194 4.62 4.93 0.014 0.016 0.36 0.41 0.695 0.725 17.65 18.42 0.290 0.300 7.37 7.62 0.420 0.440 10.67 11.18 0.153 0.159 3.89 4.04 0.153 0.158 3.89 4.04 0.230 0.250 5.84 6.35 0.220 0.240 5.59 6.10 0.910 BSC 23.11 BSC GROUND + OUTPUT + SUPPLY - OUTPUT CASE 344D-01 ISSUE B UNIBODY PACKAGE MPX2102 Sensors Freescale Semiconductor 8 Pressure PACKAGE DIMENSIONS -TC A E -Q- U N V B R PORT #1 POSITIVE PRESSURE (P1) PIN 1 -P0.25 (0.010) M T Q M 4 3 2 1 S K J F D 4 PL 0.13 (0.005) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K N P Q R S U V INCHES MILLIMETERS MIN MAX MIN MAX 1.080 1.120 27.43 28.45 0.740 0.760 18.80 19.30 0.630 0.650 16.00 16.51 0.016 0.020 0.41 0.51 0.160 0.180 4.06 4.57 0.048 0.064 1.22 1.63 0.100 BSC 2.54 BSC 0.014 0.016 0.36 0.41 0.220 0.240 5.59 6.10 0.070 0.080 1.78 2.03 0.150 0.160 3.81 4.06 0.150 0.160 3.81 4.06 0.440 0.460 11.18 11.68 0.695 0.725 17.65 18.42 0.840 0.860 21.34 21.84 0.182 0.194 4.62 4.92 G M T P S Q S STYLE 1: PIN 1. 2. 3. 4. GROUND V (+) OUT V SUPPLY V (-) OUT CASE 344F-01 ISSUE B UNIBODY PACKAGE MPX2102 9 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS PAGE 1 OF 2 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPX2102 Sensors Freescale Semiconductor 10 Pressure PACKAGE DIMENSIONS PAGE 2 OF 2 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPX2102 11 Sensors Freescale Semiconductor Pressure CASE 1320-02 ISSUE B MPAK MPX2102 12 Sensors Freescale Semiconductor Pressure CASE 1320-02 ISSUE B MPAK MPX2102 Sensors Freescale Semiconductor 13 Pressure PIN 4 PIN 1 CASE 1320A-02 ISSUE A MPAK MPX2102 14 Sensors Freescale Semiconductor Pressure CASE 1320A-02 ISSUE A MPAK MPX2102 Sensors Freescale Semiconductor 15 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 010 5879 8000 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 [email protected] MPX2102 Rev. 7 10/2008 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2008. All rights reserved.