H HiTRON PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES 30 WATTS SINGLE OUTPUT HDM30-S SERIES FEATURES: SINGLE OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED SHIELD SPECIFICATION INPUT SPECIFICATION OUTPUT SPECIFICATION Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. (Voltage refer to the –Input) Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin). OFF(Disable)=Short(or 0-0.8Vdc above-Vin). Negative Logic version option available by adding a “N” suffix to the end of Model #. Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P ±2.0% typical. Line Regulation: Various with input & output voltages. ±0.5% typical. Load Regulation: Various with output voltages. ±1.0% typical. Noise & Ripple: Typical 100mV for 3.3V/5.0V & 1.0% for others peak to peak. OVP: Built-in on main output. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. GENERAL SPECIFICATION Efficiency: 81% typical various with input. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec.@ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10 Watts. / Cubic inch. MTBF: Type 1,000,000 hours to Mil. Std.217, 25°C. Operating Temperature: -10 to +70°C range. 0°C to +60°C full load without derating. From +60°C, derating linearly to half load @+70°C. (Refer to Derating Chart.) Temperature: -20°C to +85°C. Temperature Coefficient: 0.02% /°C. Cooling: Convection cooling up to +60°C @ full load. At least 100LFM moving air is recommended for full load > +60°C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only. NOTE: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drain at low Line input & Load and then adding 20-25％for the desired fuse size. Due to requests in market and advances in technology, specifications subject to change without notice. -27- INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART SINGLE OUTPUT MODEL NO. INPUT Vdc HDM30-12B-S03 9.0HDM30-12B-S05 9.0HDM30-12B-S09 9.0HDM30-12B-S12 9.0HDM30-12B-S15 9.0HDM30-12B-S24 9.0HDM30-24B-S03 18.0HDM30-24B-S05 18.0HDM30-24B-S09 18.0HDM30-24B-S12 18.0HDM30-24B-S15 18.0HDM30-24B-S24 18.0HDM30-48B-S03 36.0HDM30-48B-S05 36.0HDM30-48B-S09 36.0HDM30-48B-S12 36.0HDM30-48B-S15 36.0HDM30-48B-S24 36.0HDM30-24D-S03 9.0HDM30-24D-S05 9.0HDM30-24D-S09 9.0HDM30-24D-S12 9.0HDM30-24D-S15 9.0HDM30-24D-S24 9.0HDM30-48D-S03 20.0HDM30-48D-S05 20.0HDM30-48D-S09 20.0HDM30-48D-S12 20.0HDM30-48D-S15 20.0HDM30-48D-S24 20.0Symbols: "★" OVP built-in. INPUT CURRENT N. L. (mA) F.L. 30 18.0 30 18.0 30 18.0 30 18.0 30 18.0 30 18.0 20 36.0 20 36.0 20 36.0 20 36.0 20 36.0 20 36.0 15 72.0 15 72.0 15 72.0 15 72.0 15 72.0 15 72.0 30 36.0 30 36.0 30 36.0 30 36.0 30 36.0 30 36.0 20 72.0 20 72.0 20 72.0 20 72.0 20 72.0 20 72.0 "@" Adjustable. 2300 2700 2650 2750 2800 3100 1150 1350 1325 1375 1400 1550 575 675 662 687 700 775 1175 1375 1350 1400 1425 1575 587 687 675 700 712 787 OUTPUT VO1(Vdc) @★ OUTPUT VO1(A) CASE SIZE 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 156.0g (5.6 Oz.) PIN ASSIGNMENT PIN NO. PIN #1. PIN #2. PIN #3. PIN #4. PIN #5. PIN #6. PIN #7. PIN #8. PIN #9. PIN #10. SINGLE Remote ON/OFF +INPUT -INPUT/-Vin NO PIN NO PIN OUTPUT TRIM NO PIN +VO1 DC-COM NO PIN DERATING CHART CASE SIZE: DM2A -28- H HiTRON PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES 30 WATTS DUAL OUTPUT HDM30-D SERIES FEATURES: DUAL OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED METAL SHIELD SPECIFICATION INPUT SPECIFICATION OUTPUT SPECIFICATION Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. (Voltage refer to the -Input). Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin). OFF(Disable)=Short(or 0-0.8Vdc above-Vin). Negative Logic version option available by adding a “N” suffix to the end of Model #. Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P ±2.0% typical. Line Regulation: Various with input voltages. ±0.5% typical. Load Regulation: Various with output voltages. VO1 ±1.0% typical. VO2 ±2.0% typical. Noise & Ripple: 100mV for 3.3V/5.0V & 1.0% typical for other output peak to peak. OVP: Built-in on main output. Adjustability: VO1 O/P may optionally be external trimmed ±3.0% with a fixed resistors or trim-pot. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. Remark: Logic voltage refer to –Input (-Vin) GENERAL SPECIFICATION Efficiency: 76- 81% typical, various with input & output voltage. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: 100K Hz. Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec. @ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10.0 Watts. / Cubic inch. MTBF: 1,000,000 hours to Mil. Std. 271, 25°C. Operating Temperature: -10°C to +70°C range. 0°C to +60°C @ full load without derating. From +60°C, derating linearly to half load@+70°C. (Refer to the Derating Chart). Temperature: -20°C to +85°C. Temperature Coefficient: ± 0.03% /°C. Cooling: Convection cooling up to +60°C @ full load. At least 100LFM moving air is recommended for F-L > +60°C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only. NOTE: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size. Due to requests in market and advances in technology, specifications subject to change without notice. -29- INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART DUAL OUTPUT MODEL NO. HDM30-12B-D05 HDM30-12B-D12 HDM30-12B-D15 HDM30-24B-D05 HDM30-24B-D12 HDM30-24B-D15 HDM30-48B-D05 HDM30-48B-D12 HDM30-48B-D15 HDM30-24D-D05 HDM30-24D-D12 HDM30-24D-D15 HDM30-48D-D05 HDM30-48D-D12 HDM30-48D-D15 INPUT Vdc 9.0- 18.0 9.0- 18.0 9.0- 18.0 18.0- 36.0 18.0- 36.0 18.0- 36.0 36.0- 72.0 36.0- 72.0 36.0- 72.0 9.0- 36.0 9.0- 36.0 9.0- 36.0 20.0- 72.0 20.0- 72.0 20.0- 72.0 Symbols: "★" OVP built-in. INPUT CURRENT OUTPUT (Vdc) N.L. (mA) F.L. +VO1@★ -VO2‖ 30 2,670 +5.0V -5.0V 30 2,500 +12.0V -12.0V 30 2,590 +15.0V -15.0V 20 1,560 +5.0V -5.0V 20 1,525 +12.0V -12.0V 20 1,525 +15.0V -15.0V 20 780 +5.0V -5.0V 20 763 +12.0V -12.0V 20 763 +15.0V -15.0V 40 1,350 + 5.0V - 5.0V 40 1,265 +12.0V -12.0V 40 1,310 +15.0V -15.0V 30 800 +5.0V -5.0V 30 775 +12.0V -12.0V 30 775 +15.0V -15.0V "@" Adjustable. OUTPUT (A) +VO1 -VO2 2.50A 2.50A 1.00A 1.00A 0.83A 0.83A 3.00A 3.00A 1.25A 1.25A 1.00A 1.00A 3.00A 3.00A 1.25A 1.25A 1.00A 1.00A 2.50A 2.50A 1.00A 1.00A 0.83A 0.83A 3.00A 3.00A 1.25A 1.25A 1.00A 1.00A CASE SIZE DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A "‖" Double Feedback. MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 156.0g (5.6 Oz.) PIN ASSIGNMENT PIN NO. PIN# 1. PIN# 2. PIN# 3. PIN# 4. PIN# 5. PIN# 6. PIN# 7. PIN# 8. PIN# 9. PIN# 10. DUAL Remote ON/OFF + INPUT -INPUT/-Vin NO PIN +VO1 DC-COM -VO2 OUTPUT TRIM NO PIN NO PIN DERATING CHART CASE SIZE: DM2A -30- H HiTRON PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES 30 WATTS TRIPLE OUTPUT HDM30-T SERIES FEATURES: TRIPLE OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED METAL SHIELD SPECIFICATION INPUT SPECIFICATION OUTPUT SPECIFICATION Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin) OFF(Disable)=Short(or 0-0.8Vdc above-Vin) Negative Logic version option available by adding a “N” suffix to the end of Model #. Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P ±2.0% typical. Line Regulation: Various with input voltages. ±0.5% typ. Load Regulation: Various with output voltages. VO1 & VO3 ±2.0% typical. VO2 ±5.0% typical. Noise & Ripple: 100mV for 3.3V/5.0V & 1.0% typical for other output peak to peak. OVP: Built-in on main output. Adjustability: VO1 O/P may optionally be external trimmed ±3.0% with a fixed resistors or trim-pot. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. Remark: [Voltage refer to –Input (-Vin)]. GENERAL SPECIFICATION Efficiency: 78-81% typical, various with input & output voltage. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: 100K Hz. Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec. @ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10.0 Watts. / Cubic inch. MTBF: 1,000,000 hours Mil.Std.271, 25°C. Operating Temperature: -10°C to +70°C range. 0°C to +60°C @ full load without derating. From+60°C derating linearly to half load@+70°C. (Refer to the Derating Chart). Storage Temperature: -20 to +85°C. Temperature Coefficient: ± 0.03% /°C. Cooling: Convection cooling up to +60°C @ full load. At least 100LFM moving air is recommended for full load > +60°C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only. NOTE: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size. Due to requests in market and advances in technology, specifications subject to change without notice. -31- INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART TRIPLE OUTPUT MODEL NO. HDM30-12B-T5/12 HDM30-12B-T5/15 HDM30-12B-T5/+12,-5 HDM30-24B-T5/12 HDM30-24B-T5/15 HDM30-24B-T5/+12,-5 HDM30-48B-T5/12 HDM30-48B-T5/15 HDM30-48B-T5/+12,-5 HDM30-24D-T5/12 HDM30-24D-T5/15 HDM30-24D-T5/+12,-5 HDM30-48D-T5/12 HDM30-48D-T5/15 HDM30-48D-T5/+12,-5 Symbols: "★" OVP built-in. INPUT Vdc 9.0- 18.0 9.0- 18.0 9.0- 18.0 18.0- 36.0 18.0- 36.0 18.0- 36.0 36.0- 72.0 36.0- 72.0 36.0- 72.0 9.0- 36.0 9.0- 36.0 9.0- 36.0 20.0- 72.0 20.0- 72.0 20.0- 72.0 INPUT CURRENT OUTPUT (Vdc) N.L. (mA) F.L. +VO1★@ +VO2† -VO3‖ 50 2,550 +5.0V +12.0V -12.0V 50 2,550 +5.0V +15.0V -15.0V 50 2,500 +5.0V +12.0V - 5.0V 40 1,520 +5.0V +12.0V -12.0V 40 1,550 +5.0V +15.0V -15.0V 40 1,420 +5.0V +12.0V - 5.0V 40 760 +5.0V +12.0V -12.0V 40 775 +5.0V +15.0V -15.0V 40 710 +5.0V +12.0V - 5.0V 60 1,325 +5.0V +12.0V -12.0V 60 1,325 +5.0V +15.0V -15.0V 60 1,300 +5.0V +12.0V - 5.0V 50 785 +5.0V +12.0V -12.0V 50 800 +5.0V +15.0V -15.0V 50 735 +5.0V +12.0V - 5.0V "@" Adjustable. "‖" Double Feedback. OUTPUT (A) +VO1 +VO2 -VO3 2.5A 0.5A 0.5A 2.5A 0.4A 0.4A 2.5A 0.5A 1.0A 3.0A 0.6A 0.6A 3.0A 0.5A 0.5A 3.0A 0.6A 1.0A 3.0A 0.6A 0.6A 3.0A 0.5A 0.5A 3.0A 0.6A 1.0A 2.5A 0.5A 0.5A 2.5A 0.4A 0.4A 2.5A 0.5A 1.0A 3.0A 0.6A 0.6A 3.0A 0.5A 0.5A 3.0A 0.6A 1.0A "†" Stacked on main O/P. MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 156.0g (5.6 Oz.) PIN ASSIGNMENT PIN NO. PIN# 1. PIN# 2. PIN# 3. PIN# 4. PIN# 5. PIN# 6. PIN# 7. PIN# 8. PIN# 9. PIN# 10. TRIPLE Remote ON/OFF +INPUT - INPUT/-Vin NO PIN +VO2 DC-COM -VO3 + VO1 NO PIN OUTPUT TRIM DERATING CHART CASE SIZE: DM2A -32- CASE SIZE DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A