AZ2501P 50 AMP LATCHING POWER RELAY FEATURES • • • • • • • 50 Amp switching Heavy loads to 13850 VA 4 kV dielectric strength 8 mm creepage distance Manual switch available Epoxy sealed version available UL, CUR file E44211 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C), SPST (1 Form A) Ratings Resistive load: Max. switched power: 13850 VA Max. switched current: 50 A Max. switched voltage: 440 VAC Rated Load UL, CUR 1 Form A (SPST) 50 A at 277 VAC, resistive, 70°C, 100k cycles 20 A at 347 VAC, resistive, 70°C, 30k cycles 5000 W at 240 VAC, tungsten, 40°C, 30k cycles 120 LRA / 20 FLA, at 120 VAC, 40°C, 30k cycles 102 LRA / 17 FLA, at 240 VAC, 40°C, 30k cycles 84 LRA / 14 FLA, at 277 VAC, 40°C, 30k cycles Life Expectancy Mechanical Electrical Minimum operations 1 x 106 1 x 105 at 50 A 250 VAC Res. (SPST) Set and Reset Pulse Duration 50 ms minimum at nominal coil voltage Set Time (typical) 15 ms at nominal coil voltage Reset Time (typical) 15 ms at nominal coil voltage Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1500 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Creepage Distance 8 mm (1 Form A), 6 mm (1 Form C) 1 Form C (SPDT) 40 A at 277 VAC, general use, 70°C, 30k cycles Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 70°C (158°F) Material Silver tin oxide Vibration 1.5mm DA at 10–55 Hz Resistance < 50 milliohms initially (at rated current, voltage drop method) Shock COIL Power At Pickup Voltage (typical) Temperature Operating 10 g, 11 ms, 1/2 sine (no false operation) Non-Operating 100 g, 11 ms, 1/2 sine (no damage) Enclosure P.B.T. polyester Terminals Tinned copper alloy .96 W single coil 1.9 W dual coil Max. Solder Temp. 270°C (518°F) Max. 105°C (221°F) Max. Solder Time 5 seconds Weight 32 grams NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 4. Initial state of contacts may be changed during transportation or shock! ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-09-08 AZ2501P RELAY ORDERING DATA COIL SPECIFICATIONS - STANDARD SINGLE COIL Nominal Coil VDC Must Operate VDC Max. Continuous VDC [1] ORDER NUMBER* Coil Resistance Ohm ± 10% 1 Form A 1 Form C AZ2501P1-1C-6D 6 4.8 7.8 24 AZ2501P1-1A-6D 9 7.2 11.7 54 AZ2501P1-1A-9D AZ2501P1-1C-9D 12 9.6 15.6 96 AZ2501P1-1A-12D AZ2501P1-1C-12D 24 19.2 31.2 384 AZ2501P1-1A-24D AZ2501P1-1C-24D 48 38.4 62.4 1536 AZ2501P1-1A-48D AZ2501P1-1C-48D COIL SPECIFICATIONS - STANDARD DUAL COIL ORDER NUMBER* Nominal Coil VDC Must Operate VDC Max. Continuous VDC [1] Coil Resistance Ohm ± 10% 1 Form A 1 Form C 6 4.8 7.8 12 AZ2501P2-1A-6D AZ2501P2-1C-6D 9 7.2 11.7 27 AZ2501P2-1A-9D AZ2501P2-1C-9D 12 9.6 15.6 48 AZ2501P2-1A-12D AZ2501P2-1C-12D 24 19.2 31.2 192 AZ2501P2-1A-24D AZ2501P2-1C-24D 48 38.4 62.4 768 AZ2501P2-1A-48D AZ2501P2-1C-48D * For epoxy sealed version (not allowed with manual switch) add suffix “E”. For manual switch add suffix “W”. For PCB retaining stud add suffix “K”. For reverse polarity coil add suffix “R”. NOTE: [1] Max. continuous voltage should not be applied for more then 60 seconds. MECHANICAL DATA PC BOARD LAYOUT Suffix “W” only .376 [9.6] .601MAX [15.3] 1.547MAX [39.3] .295 [7.5] 0.177 [4.5] .266 [6.8] .132 [3.35] .118 [3.0] 1.083 [27.5] .472 [12.0] .167 [4.3] 3x .041 [1.04] 2 5 4 3x .078 [1.98] .205 [5.2] .394 [10.0] 3 1.201MAX [30.5] 6 1 .143 [3.63] Suffix “K” only .083 [2.1] Viewed toward terminals .376 [9.6] .295 [7.5] .132 [3.35] 1.083 [27.5] .472 [12.0] .266 [6.8] .167 [4.3] .024 [0.60] .031 [0.8] .094 [2.4] 2 3 .394 [10.0] 5 4 1 .059 [1.5] .063 [1.6] Terminal 5 omitted (single coil) 6 .094 [2.4] .024 [0.60] Suffix “K” only Terminal 6 omitted (form A) Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-09-08 AZ2501P WIRING DIAGRAMS 4 4 4 3 4 6 6 1 2 SPST&Single Coil 3 3 3 1 2 SPDT&Single Coil 1 5 2 1 5 2 SPST&Double Coil SPDT&Double Coil NOTE: Standard Polarity type: 1. “Single Coil Latching Version” (1) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 2 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is disconnected. 2. “Double Coil Latching Version” (1) After energizing 5 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 5 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is disconnected. Reverse Polarity type: 1. “Single Coil Latching Version” (1) After energizing 1 (-) and 2 (+), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is disconnected. 2. “Double Coil Latching Version” (1) After energizing 5 (-) and 1 (+), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 5 (-) and 2 (+), 50ms pulse, terminal 3 and 4 is disconnected. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-09-08