NSC LM883K 3-terminal adjustable regulator Datasheet

LM117/LM317A/LM317
3-Terminal Adjustable Regulator
General Description
The LM117 series of adjustable 3-terminal positive voltage
regulators is capable of supplying in excess of 1.5A over a
1.2V to 37V output range. They are exceptionally easy to
use and require only two external resistors to set the output
voltage. Further, both line and load regulation are better than
standard fixed regulators. Also, the LM117 is packaged in
standard transistor packages which are easily mounted and
handled.
In addition to higher performance than fixed regulators, the
LM117 series offers full overload protection available only in
IC’s. Included on the chip are current limit, thermal overload
protection and safe area protection. All overload protection
circuitry remains fully functional even if the adjustment terminal is disconnected.
Normally, no capacitors are needed unless the device is
situated more than 6 inches from the input filter capacitors in
which case an input bypass is needed. An optional output
capacitor can be added to improve transient response. The
adjustment terminal can be bypassed to achieve very high
ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators.
Besides replacing fixed regulators, the LM117 is useful in a
wide variety of other applications. Since the regulator is
“floating” and sees only the input-to-output differential volt-
Typical Applications
age, supplies of several hundred volts can be regulated as
long as the maximum input to output differential is not exceeded, i.e., avoid short-circuiting the output.
Also, it makes an especially simple adjustable switching
regulator, a programmable output regulator, or by connecting
a fixed resistor between the adjustment pin and output, the
LM117 can be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping
the adjustment terminal to ground which programs the output to 1.2V where most loads draw little current.
For applications requiring greater output current, see LM150
series (3A) and LM138 series (5A) data sheets. For the
negative complement, see LM137 series data sheet.
Features
n
n
n
n
n
n
n
n
n
Guaranteed 1% output voltage tolerance (LM317A)
Guaranteed max. 0.01%/V line regulation (LM317A)
Guaranteed max. 0.3% load regulation (LM117)
Guaranteed 1.5A output current
Adjustable output down to 1.2V
Current limit constant with temperature
P+ Product Enhancement tested
80 dB ripple rejection
Output is short-circuit protected
LM117 Series Packages
Part Number
1.2V–25V Adjustable Regulator
Suffix
Design
Package
Load
Current
00906301
Full output current not available at high input-output voltages
*Needed if device is more than 6 inches from filter capacitors.
K
TO-3
1.5A
H
TO-39
0.5A
T
TO-220
1.5A
E
LCC
0.5A
S
TO-263
1.5A
EMP
SOT-223
1A
MDT
TO-252
0.5A
SOT-223 vs. D-Pak (TO-252)
Packages
†Optional — improves transient response. Output capacitors in the range
of 1µF to 1000µF of aluminum or tantalum electrolytic are commonly used
to provide improved output impedance and rejection of transients.
00906354
Scale 1:1
© 2004 National Semiconductor Corporation
DS009063
www.national.com
LM117/LM317A/LM317 3-Terminal Adjustable Regulator
July 2004
LM117/LM317A/LM317
Connection Diagrams
(TO-3)
Metal Can Package
(TO-39)
Metal Can Package
00906331
CASE IS OUTPUT
Bottom View
NS Package Number H03A
00906330
CASE IS OUTPUT
Bottom View
Steel Package
NS Package Number K02A or K02C
(TO-220)
Plastic Package
(TO-263) Surface-Mount Package
00906335
Top View
00906332
Front View
NS Package Number T03B
Ceramic Leadless
Chip Carrier
00906336
Side View
NS Package Number TS3B
00906334
Top View
NS Package Number E20A
www.national.com
2
LM117/LM317A/LM317
Connection Diagrams
(Continued)
4-Lead SOT-223
TO-252 (D-Pak)
00906359
Front View
NS Package Number MP04A
00906366
Front View
NS Package Number TD03B
Ordering Information
Package
Temperature Range
Part Number
Package Marking
Transport Media
NSC
Drawing
Metal Can
(TO-3)
−55˚C ≤ TJ ≤ +150˚C
LM117K STEEL
0˚C ≤ TJ ≤ +125˚C
LM317K STEEL
LM117K STEEL P+
50 Per Bag
K02A
LM317K STEEL P+
50 Per Bag
−55˚C ≤ TJ ≤ +150˚C
LM117K/883
LM117K/883
50 Per Bag
K02C
Metal Can
(TO-39)
−55˚C ≤ TJ ≤ +150˚C
LM117H
LM117H P+
500 Per Box
H03A
−55˚C ≤ TJ ≤ +150˚C
LM117H/883
LM117H/883
20 Per Tray
−40˚C ≤ TJ ≤ +125˚C
LM317AH
LM317AH P+
500 Per Box
0˚C ≤ TJ ≤ +125˚C
LM317H
LM317H P+
500 Per Box
TO-220
3- Lead
−40˚C ≤ TJ ≤ +125˚C
LM317AT
LM317AT P+
45 Units/Rail
0˚C ≤ TJ ≤ +125˚C
LM317T
LM317T P+
45 Units/Rail
TO-263
3- Lead
0˚C ≤ TJ ≤ +125˚C
LM317S
LM317S P+
LCC
−55˚C ≤ TJ ≤ +150˚C
SOT-223
4- Lead
0˚C ≤ TJ ≤ +125˚C
LM317SX
LM117E/883
LM117E/883
50 Units/Rail
E20A
LM317EMP
N01A
1k Units Tape and Reel
MP04A
2k Units Tape and Reel
LM317AEMP
N07A
LM317AEMPX
D- Pack
3- Lead
0˚C ≤ TJ ≤ +125˚C
1k Units Tape and Reel
2k Units Tape and Reel
LM317MDT
LM317MDT
LM317MDTX
−40˚C ≤ TJ ≤ +125˚C
TS3B
500 Units Tape and Reel
LM317EMPX
−40˚C ≤ TJ ≤ +125˚C
45 Units/Rail
T03B
75 Units/Rail
TD03B
2.5k Units Tape and Reel
LM317AMDT
LM317AMDT
LM317AMDTX
75 Units/Rail
2.5k Units Tape and Reel
3
www.national.com
LM117/LM317A/LM317
Absolute Maximum Ratings (Note 1)
ESD Tolerance (Note 5)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Power Dissipation
Storage Temperature
Operating Temperature Range
Internally Limited
Input-Output Voltage Differential
3 kV
+40V, −0.3V
LM117
−55˚C ≤ TJ ≤ +150˚C
LM317A
−40˚C ≤ TJ ≤ +125˚C
0˚C ≤ TJ ≤ +125˚C
LM317
−65˚C to +150˚C
Lead Temperature
Metal Package (Soldering, 10 seconds)
300˚C
Plastic Package (Soldering, 4 seconds)
260˚C
Preconditioning
Thermal Limit Burn-In
All Devices 100%
Electrical Characteristics (Note 3)
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA.
Parameter
Conditions
LM117 (Note 2)
Units
Min
Typ
Max
1.20
1.25
1.30
V
0.01
0.02
%/V
0.02
0.05
%/V
0.3
%
Reference Voltage
V
3V ≤ (VIN − VOUT) ≤ 40V,
10 mA ≤ IOUT ≤ IMAX, P ≤ PMAX
Line Regulation
3V ≤ (VIN − VOUT) ≤ 40V (Note 4)
Load Regulation
10 mA ≤ IOUT ≤ IMAX (Note 4)
0.1
0.3
1
%
Thermal Regulation
20 ms Pulse
0.03
0.07
%/W
50
100
µA
Adjustment Pin Current Change
10 mA ≤ IOUT ≤ IMAX
0.2
5
µA
Temperature Stability
TMIN ≤ TJ ≤ TMAX
Minimum Load Current
(VIN − VOUT) = 40V
5
mA
Current Limit
(VIN − VOUT) ≤ 15V
Adjustment Pin Current
3V ≤ (VIN − VOUT) ≤ 40V
1
3.5
%
K Package
1.5
2.2
3.4
A
H Package
0.5
0.8
1.8
A
0.3
0.4
0.15
0.2
A
0.003
%
65
dB
80
dB
(VIN − VOUT) = 40V
K Package
H Package
RMS Output Noise, % of VOUT
10 Hz ≤ f ≤ 10 kHz
Ripple Rejection Ratio
VOUT = 10V, f = 120 Hz,
A
CADJ = 0 µF
VOUT = 10V, f = 120 Hz,
66
CADJ = 10 µF
Long-Term Stability
TJ = 125˚C, 1000 hrs
0.3
1
%
Thermal Resistance,
K Package
2.3
3
˚C/W
Junction-to-Case
H Package
12
15
˚C/W
Thermal Resistance, Junction-
K Package
35
˚C/W
to-Ambient (No Heat Sink)
H Package
140
˚C/W
E Package
˚C/W
E Package
www.national.com
˚C/W
4
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA.
Parameter
Conditions
LM317A
Reference Voltage
3V ≤ (VIN − VOUT) ≤ 40V,
LM317
Min
Typ
Max
1.238
1.250
1.262
1.225
1.250
1.270
0.005
0.01
Units
Min
Typ
Max
1.20
1.25
1.30
V
0.01
0.01
0.04
%/V
0.02
0.02
0.07
%/V
V
10 mA ≤ IOUT ≤ IMAX, P ≤ PMAX
Line Regulation
Load Regulation
Thermal Regulation
3V ≤ (VIN − VOUT) ≤ 40V (Note 4)
10 mA ≤ IOUT ≤ IMAX (Note 4)
20 ms Pulse
Adjustment Pin Current
Adjustment Pin Current
Change
10 mA ≤ IOUT ≤ IMAX
Temperature Stability
TMIN ≤ TJ ≤ TMAX
Minimum Load Current
(VIN − VOUT) = 40V
Current Limit
(VIN − VOUT) ≤ 15V
0.1
0.5
0.1
0.5
%
0.3
1
0.3
1.5
%
0.04
0.07
0.04
0.07
%/W
50
100
50
100
µA
0.2
5
0.2
5
µA
3V ≤ (VIN − VOUT) ≤ 40V
1
3.5
1
10
3.5
%
10
mA
K, T, S Packages
1.5
2.2
3.4
1.5
2.2
3.4
A
H Package
MP Package
0.5
1.5
0.8
2.2
1.8
3.4
0.5
1.5
0.8
2.2
1.8
3.4
A
A
K, T, S Packages
0.15
0.4
0.15
0.4
A
H Package
MP Package
0.075
0.15
0.2
0.4
0.075
0.15
0.2
0.4
A
A
(VIN − VOUT) = 40V
RMS Output Noise, % of VOUT
10 Hz ≤ f ≤ 10 kHz
Ripple Rejection Ratio
VOUT = 10V, f = 120 Hz,
0.003
0.003
%
65
65
dB
80
dB
CADJ = 0 µF
VOUT = 10V, f = 120 Hz,
66
80
66
CADJ = 10 µF
Long-Term Stability
TJ = 125˚C, 1000 hrs
Thermal Resistance,
Junction-to-Case
K Package
MDT Package
0.3
H Package
T Package
MP Package
Thermal Resistance,
Junction-to-Ambient (No Heat
Sink)
1
0.3
1
%
2.3
5
3
˚C/W
˚C/W
15
12
15
12
4
23.5
5
4
23.5
˚C/W
˚C/W
˚C/W
˚C/W
˚C/W
K Package
MDT Package(Note 6)
35
35
92
H Package
140
140
˚C/W
T Package
50
50
˚C/W
S Package (Note 6)
50
50
˚C/W
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed.
Note 2: Refer to RETS117H drawing for the LM117H, or the RETS117K for the LM117K military specifications.
Note 3: Although power dissipation is internally limited, these specifications are applicable for maximum power dissipations of 2W for the TO-39 and SOT-223 and
20W for the TO-3, TO-220, and TO-263. IMAX is 1.5A for the TO-3, TO-220, and TO-263 packages, 0.5A for the TO-39 package and 1A for the SOT-223 Package.
All limits (i.e., the numbers in the Min. and Max. columns) are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 4: Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are
covered under the specifications for thermal regulation.
Note 5: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 6: If the TO-263 or TO-252 packages are used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the
package. Using 0.5 square inches of copper area. θJA is 50˚C/W; with 1 square inch of copper area, θJA is 37˚C/W; and with 1.6 or more square inches of copper
area, θJA is 32˚C/W. If the SOT-223 package is used, the thermal resistance can be reduced by increasing the PC board copper area (see applications hints for
heatsinking).
5
www.national.com
LM117/LM317A/LM317
Electrical Characteristics (Note 3)
LM117/LM317A/LM317
Typical Performance Characteristics
Output Capacitor = 0µF unless otherwise noted
Load Regulation
Current Limit
00906337
00906338
Adjustment Current
Dropout Voltage
00906340
00906339
Temperature Stability
Minimum Operating Current
00906341
www.national.com
00906342
6
Ripple Rejection
(Continued)
Ripple Rejection
00906344
00906343
Ripple Rejection
Output Impedance
00906346
00906345
Line Transient Response
Load Transient Response
00906347
00906348
7
www.national.com
LM117/LM317A/LM317
Typical Performance Characteristics Output Capacitor = 0µF unless otherwise noted
LM117/LM317A/LM317
can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1µF solid tantalum (or 25µF
aluminum electrolytic) on the output swamps this effect and
insures stability. Any increase of the load capacitance larger
than 10µF will merely improve the loop stability and output
impedance.
Application Hints
In operation, the LM117 develops a nominal 1.25V reference
voltage, VREF, between the output and adjustment terminal.
The reference voltage is impressed across program resistor
R1 and, since the voltage is constant, a constant current I1
then flows through the output set resistor R2, giving an
output voltage of
LOAD REGULATION
The LM117 is capable of providing extremely good load
regulation but a few precautions are needed to obtain maximum performance. The current set resistor connected between the adjustment terminal and the output terminal (usually 240Ω) should be tied directly to the output (case) of the
regulator rather than near the load. This eliminates line
drops from appearing effectively in series with the reference
and degrading regulation. For example, a 15V regulator with
0.05Ω resistance between the regulator and load will have a
load regulation due to line resistance of 0.05Ω x IL. If the set
resistor is connected near the load the effective line resistance will be 0.05Ω (1 + R2/R1) or in this case, 11.5 times
worse.
Figure 2 shows the effect of resistance between the regulator and 240Ω set resistor.
00906305
FIGURE 1.
Since the 100µA current from the adjustment terminal represents an error term, the LM117 was designed to minimize
IADJ and make it very constant with line and load changes.
To do this, all quiescent operating current is returned to the
output establishing a minimum load current requirement. If
there is insufficient load on the output, the output will rise.
00906306
FIGURE 2. Regulator with Line Resistance in Output
Lead
EXTERNAL CAPACITORS
An input bypass capacitor is recommended. A 0.1µF disc or
1µF solid tantalum on the input is suitable input bypassing
for almost all applications. The device is more sensitive to
the absence of input bypassing when adjustment or output
capacitors are used but the above values will eliminate the
possibility of problems.
The adjustment terminal can be bypassed to ground on the
LM117 to improve ripple rejection. This bypass capacitor
prevents ripple from being amplified as the output voltage is
increased. With a 10µF bypass capacitor 80dB ripple rejection is obtainable at any output level. Increases over 10µF do
not appreciably improve the ripple rejection at frequencies
above 120Hz. If the bypass capacitor is used, it is sometimes necessary to include protection diodes to prevent the
capacitor from discharging through internal low current paths
and damaging the device.
In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance even at
high frequencies. Depending upon capacitor construction, it
takes about 25µF in aluminum electrolytic to equal 1µF solid
tantalum at high frequencies. Ceramic capacitors are also
good at high frequencies; but some types have a large
decrease in capacitance at frequencies around 0.5MHz. For
this reason, 0.01µF disc may seem to work better than a
0.1µF disc as a bypass.
Although the LM117 is stable with no output capacitors, like
any feedback circuit, certain values of external capacitance
www.national.com
With the TO-3 package, it is easy to minimize the resistance
from the case to the set resistor, by using two separate leads
to the case. However, with the TO-39 package, care should
be taken to minimize the wire length of the output lead. The
ground of R2 can be returned near the ground of the load to
provide remote ground sensing and improve load regulation.
PROTECTION DIODES
When external capacitors are used with any IC regulator it is
sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator. Most 10µF capacitors have low enough
internal series resistance to deliver 20A spikes when
shorted. Although the surge is short, there is enough energy
to damage parts of the IC.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the
regulator, and the rate of decrease of VIN. In the LM117, this
discharge path is through a large junction that is able to
sustain 15A surge with no problem. This is not true of other
types of positive regulators. For output capacitors of 25µF or
less, there is no need to use diodes.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs
8
LM117/LM317A/LM317
Application Hints
(Continued)
when either the input or output is shorted. Internal to the
LM117 is a 50Ω resistor which limits the peak discharge
current. No protection is needed for output voltages of 25V
or less and 10µF capacitance. Figure 3 shows an LM117
with protection diodes included for use with outputs greater
than 25V and high values of output capacitance.
00906355
FIGURE 4. θ(J−A) vs Copper (1 ounce) Area for the
TO-263 Package
00906307
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. It should also
be observed that the minimum value of θ(J−A) for the TO-263
package mounted to a PCB is 32˚C/W.
As a design aid, Figure 5 shows the maximum allowable
power dissipation compared to ambient temperature for the
TO-263 device (assuming θ(J−A) is 35˚C/W and the maximum junction temperature is 125˚C).
D1 protects against C1
D2 protects against C2
FIGURE 3. Regulator with Protection Diodes
When a value for θ(H−A) is found using the equation shown,
a heatsink must be selected that has a value that is less than
or equal to this number.
θ(H−A) is specified numerically by the heatsink manufacturer
in the catalog, or shown in a curve that plots temperature rise
vs power dissipation for the heatsink.
HEATSINKING TO-263, SOT-223 AND TO-252 PACKAGE
PARTS
The TO-263 (“S”), SOT-223 (“MP”) and TO-252 (”DT”) packages use a copper plane on the PCB and the PCB itself as
a heatsink. To optimize the heat sinking ability of the plane
and PCB, solder the tab of the package to the plane.
Figure 4 shows for the TO-263 the measured values of θ(J−A)
for different copper area sizes using a typical PCB with 1
ounce copper and no solder mask over the copper area used
for heatsinking.
00906356
FIGURE 5. Maximum Power Dissipation vs TAMB for
the TO-263 Package
Figure 6 and Figure 7 show the information for the SOT-223
package. Figure 7 assumes a θ(J−A) of 74˚C/W for 1 ounce
copper and 51˚C/W for 2 ounce copper and a maximum
junction temperature of 125˚C.
9
www.national.com
LM117/LM317A/LM317
Application Hints
mine if a heatsink is needed, the power dissipated by the
regulator, PD, must be calculated:
IIN = IL + IG
PD = (VIN − VOUT) IL + VINIG
Figure 8 shows the voltage and currents which are present in
the circuit.
(Continued)
00906360
00906357
FIGURE 8. Power Dissipation Diagram
FIGURE 6. θ(J−A) vs Copper (2 ounce) Area for the
SOT-223 Package
The next parameter which must be calculated is the maximum allowable temperature rise, TR(max):
TR(max) = TJ(max) − TA(max)
where TJ(max) is the maximum allowable junction temperature (125˚C), and TA(max) is the maximum ambient temperature which will be encountered in the application.
Using the calculated values for TR(max) and PD, the maximum allowable value for the junction-to-ambient thermal
resistance (θJA) can be calculated:
θJA = TR(max)/PD
If the maximum allowable value for θJA is found to be
≥92˚C/W (Typical Rated Value) for TO-252 package, no
heatsink is needed since the package alone will dissipate
enough heat to satisfy these requirements. If the calculated
value for θJA falls below these limits, a heatsink is required.
As a design aid, Table 1 shows the value of the θJA of
TO-252 for different heatsink area. The copper patterns that
we used to measure these θJAs are shown at the end of the
Application Notes Section. Figure 9 reflects the same test
results as what are in the Table 1
Figure 10 shows the maximum allowable power dissipation
vs. ambient temperature for the TO-252 device. Figure 11
shows the maximum allowable power dissipation vs. copper
area (in2) for the TO-252 device. Please see AN1028 for
power enhancement techniques to be used with SOT-223
and TO-252 packages.
00906358
FIGURE 7. Maximum Power Dissipation vs TAMB for
the SOT-223 Package
The LM317 regulators have internal thermal shutdown to
protect the device from over-heating. Under all possible
operating conditions, the junction temperature of the LM317
must be within the range of 0˚C to 125˚C. A heatsink may be
required depending on the maximum power dissipation and
maximum ambient temperature of the application. To deter-
TABLE 1. θJA Different Heatsink Area
Layout
www.national.com
Copper Area
Thermal Resistance
Top Side (in2)*
Bottom Side (in2)
(θJA˚C/W) TO-252
1
0.0123
0
103
2
0.066
0
87
3
0.3
0
60
4
0.53
0
54
5
0.76
0
52
6
1
0
47
7
0
0.2
84
8
0
0.4
70
9
0
0.6
63
10
LM117/LM317A/LM317
Application Hints
(Continued)
TABLE 1. θJA Different Heatsink Area (Continued)
Layout
Copper Area
Thermal Resistance
10
0
0.8
57
11
0
1
57
12
0.066
0.066
89
13
0.175
0.175
72
14
0.284
0.284
61
15
0.392
0.392
55
16
0.5
0.5
53
Note: * Tab of device attached to topside of copper.
00906361
FIGURE 9. θJA vs 2oz Copper Area for TO-252
00906363
FIGURE 10. Maximum Allowable Power Dissipation vs. Ambient Temperature for TO-252
11
www.national.com
LM117/LM317A/LM317
Application Hints
(Continued)
00906362
FIGURE 11. Maximum Allowable Power Dissipation vs. 2oz Copper Area for TO-252
00906364
FIGURE 12. Top View of the Thermal Test Pattern in Actual Scale
www.national.com
12
LM117/LM317A/LM317
Application Hints
(Continued)
00906365
FIGURE 13. Bottom View of the Thermal Test Pattern in Actual Scale
13
www.national.com
LM117/LM317A/LM317
Schematic Diagram
00906308
Typical Applications
Adjustable Regulator with Improved Ripple Rejection
5V Logic Regulator with Electronic Shutdown*
00906310
†Solid tantalum
*Discharges C1 if output is shorted to ground
00906303
*Min. output ) 1.2V
High Stability 10V Regulator
Slow Turn-On 15V Regulator
00906309
00906311
www.national.com
14
LM117/LM317A/LM317
Typical Applications
(Continued)
High Current Adjustable Regulator
00906312
‡ Optional — improves ripple rejection
†Solid tantalum
*Minimum load current = 30 mA
Power Follower
0 to 30V Regulator
00906313
00906314
Full output current not available at high input-output voltages
15
www.national.com
LM117/LM317A/LM317
Typical Applications
(Continued)
5A Constant Voltage/Constant Current Regulator
00906315
†Solid tantalum
*Lights in constant current mode
1A Current Regulator
High Gain Amplifier
00906316
1.2V–20V Regulator with Minimum Program Current
00906318
00906317
*Minimum load current ) 4 mA
www.national.com
16
LM117/LM317A/LM317
Typical Applications
(Continued)
Low Cost 3A Switching Regulator
00906319
†Solid tantalum
*Core — Arnold A-254168-2 60 turns
4A Switching Regulator with Overload Protection
00906320
†Solid tantalum
*Core — Arnold A-254168-2 60 turns
Precision Current Limiter
00906321
17
www.national.com
LM117/LM317A/LM317
Typical Applications
(Continued)
Tracking Preregulator
00906322
Current Limited Voltage Regulator
00906323
(Compared to LM117’s higher current limit)
— At 50 mA output only 3⁄4 volt of drop occurs in R3 and R4
Adjusting Multiple On-Card Regulators with Single Control*
00906324
*All outputs within ± 100 mV
†Minimum load — 10 mA
www.national.com
18
LM117/LM317A/LM317
Typical Applications
(Continued)
AC Voltage Regulator
00906325
12V Battery Charger
00906326
Use of RS allows low charging rates with fully charged battery.
50mA Constant Current Battery Charger
00906327
19
www.national.com
LM117/LM317A/LM317
Typical Applications
(Continued)
Adjustable 4A Regulator
00906328
Digitally Selected Outputs
Current Limited 6V Charger
00906329
00906302
*Sets peak current (0.6A for 1Ω)
*Sets maximum VOUT
**The 1000µF is recommended to filter out input transients
www.national.com
20
LM117/LM317A/LM317
Physical Dimensions
inches (millimeters)
unless otherwise noted
TO-3 Metal Can Package (K)
NS Package Number K02A
TO-3 Metal Can Package (K)
Mil-Aero Product
NS Package Number K02C
21
www.national.com
LM117/LM317A/LM317
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
(TO-39) Metal Can Package
NS Package Number H03A
3-Lead TO-220
NS Package Number T03B
www.national.com
22
LM117/LM317A/LM317
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead TO-263
NS Package Number TS3B
23
www.national.com
LM117/LM317A/LM317
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
Ceramic Leadless Chip Carrier
NS Package Number E20A
4-Lead SOT-223
NS Package Number MP04A
www.national.com
24
LM117/LM317A/LM317 3-Terminal Adjustable Regulator
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead D-Pack
NS Package Number TD03B
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.