Teledyne J412T-5M Established reliability to-5 relay Datasheet

SERIES
ESTABLISHED RELIABILITY
ESTABLISHED RELIABILITY
TO-5 RELAYS
412
DPDT
SERIES
DESIGNATION
RELAY TYPE
412
DPDT basic relay
412D
DPDT relay with internal diode for coil suppression
DPDT relay with internal diodes for coil transient suppression and polarity
reversal protection
412DD
DPDT relay with internal transistor driver and coil transient suppression
diode
412T
INTERNAL CONSTRUCTION
UNI-FRAME
DESCRIPTION
UPPER
STATIONARY
CONTACT
ARMATURE
LOWER
STATIONARY
CONTACT
MOVING
CONTACT
ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
Temperature
(Ambient)
–65°C to +125°C
Vibration
(General Note 1)
30 g’s to 3000 Hz
Shock
(General Note 1)
75 g’s,
6 msec, half-sine
Acceleration
50 g’s
Enclosure
Hermetically sealed
Weight
0.09 oz. (2.55g) max.
©2003 TELEDYNE RELAYS
The TO-5 relay, originally conceived and developed by Teledyne, has become
one of the industry standards for low-level switching from dry circuit to 1
ampere. Designed expressly for high-density PC board mounting, its small size
and low coil power dissipation make the 412 relay one of the most versatile
ultraminiature relays available.
The following unique construction features and manufacturing techniques
provide excellent resistance to environmental extremes and overall high
reliability.
• All welded construction.
• Unique uni-frame design, providing high magnetic efficiency and
mechanical rigidity.
• High force/mass ratios for resistance to shock and vibration.
• Advanced cleaning techniques provide maximum assurance of internal
cleanliness.
• Precious metal alloy contact material with gold plating assures excellent
high current and dry circuit switching capabilities.
The Series 412D and 412DD relays have internal discrete silicon diodes for
coil suppression and polarity reversal protection. The hybrid 412T relay
features an internal silicon suppression diode and transistor driver. This hybrid
package reduces required PC board floor space by reducing the number of
external components needed to drive the relay.
By virtue of its inherently low intercontact capacitance and contact circuit
losses, the 412 relay has proven to be an excellent ultraminiature RF switch
for frequency ranges well into the UHF spectrum. A typical RF application for
the TO-5 relay is in handheld radio transceivers, wherein the combined
features of good RF performance, small size, low coil power dissipation and
high reliability make it a preferred method of T-R switching (see Figure 1).
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
412 Page 1
412/1203/Q1
SERIES 412
GENERAL ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Notes 2 & 3)
Contact Arrangement
Rated Duty
Contact Resistance
2 Form C (DPDT)
Continuous
0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header)
Contact Load Ratings (DC)
(See Fig. 2 for other DC
resistive voltage/current ratings)
Resistive:
Inductive:
Lamp:
Low Level:
1 Amp/28Vdc
200 mA/28Vdc (320 mH)
100 mA/28Vdc
10 to 50 μA/10 to 50mV
Resistive:
250 mA/115Vac, 60 and 400 Hz (Case not grounded)
100 mA/115Vac, 60 and 400 Hz (Case grounded)
Contact Load Ratings (AC)
ESTABLISHED RELIABILITY
10,000,000 cycles (typical) at low level
1,000,000 cycles (typical) at 0.5A/28Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Life Ratings
Contact Overload Rating
2A/28Vdc Resistive (100 cycles min.)
Contact Carry Rating
Contact factory
Coil Operating Power
450 milliwatts typical at nominal rated voltage @ 25°C
Operate Time
2.0 msec max. at nominal rated coil voltage
Release Time
412 Series: 1.5 msec max. 412D, 412DD Series: 4.0 msec max. 412T Series: 7.5 msec max.
Contact Bounce
1.5 msec max.
Intercontact Capacitance
0.4 pf typical
Insulation Resistance
10,000 megohms min. between mutually isolated terminals
Dielectric Strength
Atmospheric pressure: 500 Vrms/60Hz
70,000 ft.: 125 Vrms/60Hz
Negative Coil Transient (Vdc)
412D, 412DD, 412T
1.0 max
Diode P.I.V. (Vdc)
412D, 412DD, 412T
100 min.
Base Turn Off Voltage (Vdc)
0.3 min.
412T
Transistor
Emitter-base breakdown Voltage (BVEBO) (@25°C) (Vdc)
6.0 min.
Characteristics
Collector-base breakdown Voltage (BVEBO) (@25°C & lc = 100 μA) (Vdc)
75 min.
DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Note 3)
412-5
412D-5
412DD-5
412T-5
5.0
5.8
50
39
93.2
128.2
82.2
112.1
3.5
3.9
3.5
3.00
0.14
2.3
0.6
2.8
BASE PART
NUMBERS
(See Note 10 for full P/N example)
Nom.
Max.
412, 412D, 412T (Note 4)
Coil Resistance
(Ohms ±10% @25°C)
412DD (Note 4)
Min.
Coil Current (mAdc @25°C)
(412DD Series)
Max.
Min.
Coil Current (mAdc @25°C)
(Note 7)
(412T Series)
Max.
412, 412D
Pick-up Voltage (Vdc, Max.)
412DD
412T (Note 7)
Base Current to Turn On (mAdc, Max.) (412T Series) (Note 7)
Min.
412, 412D, 412T
Max.
Drop-out Voltage (Vdc)
Min.
412DD
Max.
Coil Voltage (Vdc)
412-6
412D-6
412DD-6
412T-6
6.0
8.0
98
78
58.3
78.3
52.9
69.9
4.5
5.2
4.5
2.04
0.18
3.2
0.7
3.4
412-9
412D-9
412DD-9
412T-9
9.0
12.0
220
220
33.0
42.9
35.3
47.4
6.8
7.8
6.8
1.36
0.35
4.9
0.8
5.3
PERFORMANCE CURVES
TYPICAL RF PERFORMANCE
(NOTE 2)
0
ER
TIO
OS
10
1.92
)
WR
SS (VS
1.22
N LO
RETUR
30
CTS
1.07
NTA
40
N
ATIO
CO
OSS
ACR
ISOL
50
TION
OLA
OSS
ACR
LES
1.02
PO
1.01
IS
60
250
200
150
100
50
1.00
70
1.00
.01
FIGURE 1
412 Page 2
VSWR
dB
.4
LOAD VOLTAGE (VDC)
S
.3
20
412-26
412D-26
412DD-26
412T-26
26.5
32.0
1560
1560
14.8
18.5
14.7
19.8
18.0
19.0
18.0
0.50
0.89
13.0
1.4
13.0
300
NL
.2
412-18
412D-18
412DD-18
412T-18
18.0
24.0
880
880
17.5
22.1
17.9
24.0
13.5
14.5
13.5
0.68
0.59
10.0
1.1
10.0
TYPICAL DC CONTACT RATING (RESISTIVE)
INS
.1
412-12
412D-12
412DD-12
412T-12
12.0
16.0
390
390
25.6
32.8
26.6
35.8
9.0
10.0
9.0
1.03
0.41
6.5
0.9
6.5
0.5
.1
FREQUENCY (GHz)
.5
1.0
0
FIGURE 2
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
LOAD CURRENT (AMPS DC)
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
©2003 TELEDYNE RELAYS
412/1203/Q1
SERIES 412
OUTLINE DIMENSIONS
SCHEMATIC DIAGRAMS
TERMINAL LOCATIONS AND PIN NUMBERING (REF. ONLY)
(Viewed from Terminals)
.370
(9.40)
DIA. MAX.
.031 (.79)
± .003 (0.08)
.335
(8.51)
DIA. MAX.
10
TRANSISTOR BASE
CONNECTION FOR
412T ONLY
.035 (.89)
± .010 (0.25)
9
412
412DD
412D
412T
1
8
2
7
3
.270 (6.86) MAX.
ESTABLISHED RELIABILITY
WIRE LEAD: .75 (19.05) MIN.
PIN: .187 (4.75) ±.010 (.25)
(See Note 6)
+.002 (.05)
.017 (.43) –.001 (.03) DIA.
6
36° ±3°
TYP.
.200 (5.08)
± .010 (.25) DIA.
4
5
SCHEMATICS ARE VIEWED
FROM TERMINALS
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
TYPICAL LOGIC INTERFACE
GENERAL NOTES
(See Note 8)
1. Relay contacts will exhibit no chatter in excess of 10 μsec or transfer in excess of
1 μsec.
2. “Typical” characteristics are based on available data and are best estimates. No
on-going verification tests are performed.
3. Unless otherwise specified, parameters are initial values.
4. For reference only. Coil resistance not directly measurable at relay terminals due
to internal series semiconductor. 412DD and 412T only.
5. Unless otherwise specified, relays will be supplied with either gold-plated or
solder-coated leads.
6. The slash and characters appearing after the slash are not marked on the relay.
7. Limit Base Emitter current to 15 mAdc.
8. Applicable to all coil voltages. See Base current to turn on.
9. Screened HI-REL versions available. Contact factory.
10.
Vcc
Vr
Pin 1
Notes:
Logic 1 activates the relay.
Logic 0 de-activates the relay.
Vcc = logic bias power.
Vr = coil energization voltage.
Logic element
Pin 10
1 = 0.50 to 3.00mA
0 = 0.3Vdc min.
Pin 9
Teledyne Part Numbering System for T2R® Established Reliability Relay
ER
412 Y
M - 26
A / S Q
Established Reliability
Designator
Q= Solder-Coated Leads
G= Gold-Plated Leads
(Notes 5 and 6)
S= .187" leads
(Note 6)
Relay Series
Optional Ground Pin
(See Appendix)
Screening and Reliability
Level
Pad Option
(See Appendix)
Coil Voltage
Teledyne Part Numbering System for Military Qualified (JAN) Relays
J
412 Y
M - 26 P
L
Military (JAN)
Designator
Screening and Reliability
Level
Relay Series
Optional Ground Pin
(See Appendix)
Terminal Variant
P = 0.187"
Coil Voltage
Spreader Option
(See Appendix)
©2003 TELEDYNE RELAYS
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
412 Page 3
412/1203/Q1
Appendix A: Spacer Pads
Pad designation and
bottom view dimensions
Height
Ø.150
[3.81]
(REF)
Dim H
MAX
“M4” Pad for TO-5
Dim H
MAX
“M4” Pad for TO-5
Dim H
MAX
“M4” Pad for Centigrid®
.156
[3.96]
(REF)
Dim H
MAX
.256
[6.5]
(REF)
“M9” Pad for Centigrid®
For use with the following:
ER411T
ER412, ER412D, ER412DD
712, 712D, 712TN,
RF300, RF310, RF320
ER420, ER422D, ER420DD, 421,
ER421D, ER421DD, ER422, ER422D,
ER422DD, 722, 722D, RF341
ER431T, ER432T,
ER432, ER432D, ER432DD
732, 732D, 732TN, RF303, RF313,
RF323
.295 (7.49)
.300 (7.62)
.305 (7.75)
.400 (10.16)
.410 (10.41)
RF312
.350 (8.89)
ER411, ER411D, ER411DD
.295 (7.49)
ER431, ER431D, ER431DD
.400 (10.16)
RF311
.300 (7.62)
RF331
.410 (10.41)
172, 172D
.305 (7.75)
ER114, ER114D, ER114DD,
J114, J114D, J114DD
.300 (7.62)
ER134, ER134D, ER134DD,
J134, J134D, J134DD
.400 (10.16)
RF100
.315 (8.00)
RF103
.420 (10.67)
122C, A152
.320 (8.13)
ER116C, J116C
.300 (7.62)
ER136C, J136C
.400 (10.16)
RF180
.325 (8.25)
A150
.305 (7.75)
Notes:
1. Spacer pad material: Polyester lm.
2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering
example in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise specied, tolerance is ± .010 (.25).
5. Add 10 m to the contact resistance show in the datasheet.
6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
© 2008 Teledyne Relays
Dim. H
Max.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Appendix A: Spreader Pads
Pad designation and
bottom view dimensions
Height
For use with the following:
.370 [9.4]
MAX SQ
.100
[2.54]
Dim H
MAX
.150
[3.81]
.014
[0.36]
(REF)
.300
[7.62]
.100
[2.54]
.370
[9.4]
MIN
.200
[5.08]
“M” Pad 5/ 6/
.390 [9.91]
SQ
.100
[2.54]
.100
[2.54]
.150
[3.81]
.300
[7.62]
.300
[7.62]
.150
[3.81]
Dim H
MAX
ER411T, J411T, ER412, ER412D
ER412DD, J412, J412D, J412DD
ER412T, J412T
712, 712D, 712TN
ER431T, J431T, ER432, ER432D
ER432DD, J432, J432D, J432DD
ER432T, J432T
732, 732D, 732TN
.370 [9.4]
MAX SQ
.100
[2.54]
Dim H
MAX
.150
[3.81]
.014
[0.36]
(REF)
.300
[7.62]
.100
[2.54]
.200
[5.08]
.370
[9.4]
MIN
“M3” Pad 5/ 6/ 9/
.393 (9.99)
.493 (12.52)
.503 (12.78)
.398 (10.11)
ER411T
ER412, ER412D, ER412DD
J412, J412D, J412DD
.441 (11.20)
732, 732D
“M2” Pad 7/ 8/
.388 (9.86)
ER420, J420, ER420D, J420D
ER420DD, J420DD, ER421, J421
ER421D, J421D, ER421DD
J422D, ER422DD, J422DD, 722
712, 712D
ER421, ER421D, ER421DD
722, 732D
ER431T
ER432, ER432D, ER432DD
.130
[3.3]
Dim. H
Max.
ER411, ER411D, ER411DD
ER411TX
ER412X, ER412DX, ER412DDX
ER412TX
712X, 712DX, 712TNX
ER420X, ER420DX, ER420DDX
ER421X, ER421DX, ER421DDX
ER422X, ER422DX
ER422DDX, 722X, 722DDX
ER431, ER431D, ER431DD
ER431TX
ER432X, ER432DX, ER432DDX
ER432TX
732X, 732DX, 732TNX
.451 (11.46)
.451 (11.46)
.546 (13.87)
.556 (14.12)
.388 (9.86)
.393 (9.99)
.398 (10.11)
.493 (12.52)
.503 (12.78)
Notes:
1. Spreader pad material: Diallyl Phthalate.
2. To specify an “M”, “M2” or “M3” spreader pad, refer to the mounting variants portion of the part number example
in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise specied, tolerance is ± .010” (0.25).
5/. Add 25 m to the contact resistance shown in the datasheet.
6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
7/. Add 50 m to the contact resistance shown in the datasheet.
8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet.
9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.)
(800) 284-7007 • www.teledynerelays.com
+44 (0) 1236 453124 • www.teledyne-europe.com
© 2008 Teledyne Relays
Appendix A: Ground Pin Positions
Ø.200
[Ø5.08]
36°±3°
"Z"
POSITION
"X"
POSITION
"Y"
POSITION
"Z"
Ø.200
[Ø5.08]
"Y"
45°±3°
TO-5 Relays:
ER411T, ER412, ER412T, ER420, ER421, ER422,
ER431T, ER432, ER432T, 712, 712TN, 400H, 400K,
400V, RF300, RF303, RF341, RF312, RF310, RF313,
RF320, RF323
"Y"
POSITION
POSITION
TO-5 Relays:
ER411, ER431, RF311, RF331
POSITION
.100
[2.54]
"W"
"Z"
.100
[2.54]
.050
[1.27]
"X"
.100
[2.54]
POSITION
POSITION
"Z"
POSITION
POSITION
.100
[2.54]
POSITION
"U"
POSITION
(ER116C and ER136C only)
Centigrid® Relays:
RF180, ER116C, 122C, ER136C
.100
[2.54]
Centigrid® Relays:
RF100, RF103, ER114, ER134, 172
Indicates ground pin position
Indicates glass insulated lead position
Indicates ground pin or lead position
depending on relay type
© 2008 Teledyne Relays
"Y"
.100
[2.54]
NOTES
1. Terminal views shown
2. Dimensions are in inches (mm)
3. Tolerances: ± .010 (±.25) unless otherwise specied
4. Ground pin positions are within .015 (0.38) dia. of true position
5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref.
6. Lead dia. 0.017 (0.43) nom.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE