CURRENT SENSING CHIP RESISTORS HOW TO ORDER CRL10 R020 J N M Packaging M = Tape/Reel FEATURES B = Bulk TCR (PPM/°°C) K=+100 L=+200 O=+400 Q=+600 N=+300 M=+500 Tolerance (%) F = +1 G = +2 J = +5 Current Sensing Resistor Reference Standard = IEC 60115-8, JIS C 5201-8 EIA Resistance Value Standard decade values Series Size CRL05 = 0402 CRL16 = 0603 CRL10 = 0805 CRL18 = 1206 CRL14 = 1210 DERATING CURVE CRL12 = 2010 CRL01 = 2512 CR12S = 0612 CR1S = 3720 CRL02 = 7520 DIMENSIONS (mm) Size 0402 0603 0805 1206 2010 2512 3720 0612 L 1.00 + 0.05 1.60 + 0.10 2.00 + 0.15 3.10 + 0.15 5.00 + 0.15 6.30 + 0.15 3.75 + 0.20 7.50 + 0.20 W 0.50 + 0.05 0.80 + 0.10 1.25 + 0.15 1.55 + 0.15 2.50 + 0.15 3.10 + 0.15 2.00 + 0.20 2.00 + 0.20 D1 0.25 + 0.10 0.30 + 0.20 0.30 + 0.20 0.50 + 0.30 0.60 + 0.30 0.60 + 0.30 0.40+ 0.20 0.40+ 0.20 D2 0.20 + 0.10 0.30 + 0.20 0.30 + 0.20 0.40 + 0.20 0.50 + 0.25 0.50 + 0.25 0.40 + 0.20 0.40 + 0.20 Tt 0.32 + 0.05 0.45 + 0.10 0.50 + 0.10 0.60 + 0.10 0.60 + 0.10 0.60 + 0.10 0.60 + 0.10 0.60 + 0.10 ±300 0.100 ~ 0.200 0.100 ~ 0.910 Max TCR (ppm/°C) Per Resistance Range in Ω ±250 ±200 ±150 0.220 ~ 1.000 0.010 ~ 0.200 0402 0603 ±1, ±2, ±5 ±1, ±2, ±5 0805 ±1, ±2, ±5 0.100 ~ 0.910 0.010 ~ 0.091 1206 1210 2010 ±1, ±2, ±5 ±1, ±2, ±5 ±1, ±2, ±5 0.100 ~ 0.910 2512 ±1, ±2, ±5 0.010 ~ 0.091 0.100 ~ 0.910 0.100 ~ 0.910 0.010 ~ 0.091 0.100 ~ 0.910 3720 0612 ±1, ±2, ±5 ±1, ±2, ±5 0.001 ~ 0.050 0.100 ~ 0.200 ±100 0.021 ~ 0.910 0.005 ~ 0.020 0.210 ~ 0.910 0.002 ~ 0.030 0.005 ~ 0.030 Rated Power 1/16 W 1/10 W 1/8 W 1/4 W 1/4 W 1/2 W 0.001 ~ 0.010 1W 0.001 ~ 0.030 0.001 ~ 0.010 0.5W & 1W 0.5W & 1W Operating Temp. Range is -55°C ~ + 125°C Tolerance (%) Operating Current I = √(P/R) Size Operating Voltage V = √(P*R) RATING & CHARACTERISTIC PERFORMANCE Item Temp. Coefficient of Resistance Short Time Overload Dielectric Withstand Voltage Insulation Resistance Thermal Shock Load Life Humidity (Stable State) Resistance to Dry Heat Low Temperature Operation Bending Strength Solderability Resistance to Soldering Heat Specification As Spec ±(0.5% + 0.05Ω) By type >1000M Ω ±(0.5% + 0.05Ω) ±(1% + 0.05Ω) ±(1% + 0.05Ω) ±(0.5% + 0.05Ω) ±(0.5% + 0.05Ω) ±(0.5% + 0.05Ω) 95% min. Coverage ±(0.5% + 0.05Ω) Test Method ~ MIL-STD-202F, Method 304 304 +25/-55/+25/+125/+25°C JIS-C-5202-5.5 RCWV*2.5orMax Overloading Voltage 5 seconds MIL-STD-202F, Method 301 Apply Max Overload Voltage for 1 minute MIL-STD-202F, Method 302 Apply 100VDC for 1 minute MIL-STD-202F, Method 107G -55°C ~ + 150°C, 100 cycles MIL-STD-202F, Method 108A RCWV 70°C, 1.5 hrs ON, 0.5 hrs off, 1000 ~ 1048 hrs MIL-STD-202F, Method 103B 40°C, 90~95%RH , RCWV 1.5 hrs ON, 0.5 hrs OFF, total 1000 ~ 1048 hrs JIS-C-5202 7.2 96 hours @ +125°C without load JIS-C-5202 7.1 1 hour, -65°C followed by 45 minutes if RCWV JIS-C-5202 6.1.4 Bending Amplitude 3mm for 10 seconds MIL-STD-202F, Method 208H 235°C±5°C, 2±0.5 (sec) MIL-STD-202F, Method 210E 260±5°C ,10±1second The content of this specification may change without notification 5/15/2015 American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 1