CEN-100 100W Single Output LED Power Supply series ½ Features : Universal AC input / Full range (up to 295VAC) Protections: Short circuit / Over current / Over voltage / Over temperature Output voltage and constant current level adjustable Built-in active PFC function IP66 design for indoor or outdoor installations Cooling by free air convection 100% full load burn-in test High reliability Suitable for LED lighting and moving sign applications Compliance to worldwide safety regulations for lighting Suitable for dry / damp / wet locations 3 years warranty F 110 SELV SPECIFICATION MODEL CEN-100-20 CEN-100-24 20V DC VOLTAGE CONSTANT CURRENT OPERATION VOLTAGE Note.5 13 ~ 20V OUTPUT 30V 36V 42V 48V 54V 19.5 ~ 30V 23.4 ~ 36V 27.3 ~ 42V 31.2 ~ 48V 35.1 ~ 54V 3.2A 2.65A 2.28A 2A 1.77A 0 ~ 4A 0 ~ 3.2A 0 ~ 2.65A 0 ~ 2.28A 0 ~ 2A 0 ~ 1.77A RATED POWER 96W 96W 96W 95.4W 95.76W 96W 95.58W RIPPLE & NOISE (max.) Note.2 2.0Vp-p 2.7Vp-p 3Vp-p 3.6Vp-p 4Vp-p 4.6Vp-p 5Vp-p VOLTAGE ADJ. RANGE (SVR1) 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 37 ~ 46V 43 ~ 53V 49 ~ 58V CURRENT ADJ. RANGE(SVR2) 3.12 ~ 4.8A 2.6 ~ 4A 2.08 ~ 3.2A 1.72 ~ 2.65A 1.48 ~ 2.28A 1.3 ~ 2A 1.15 ~ 1.77A VOLTAGE TOLERANCE Note.3 10% LINE REGULATION 3.0% 5.0% 3000ms / 230VAC 5000ms / 115VAC at full load Note.4 90 ~ 295VAC 127 ~ 417VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) EFFICIENCY (Typ.) 88% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.4A/115VAC 60A/230VAC 89% 90% 90% 90% 91% <0.75mA / 240VAC OVER CURRENT 95 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed OVER VOLTAGE WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT Hiccup mode, recovers automatically after fault condition is removed 22.8 ~ 26V 28 ~ 32V 34 ~ 38V 41 ~ 46V 47 ~ 52V 100 10 (RTH1) -30 ~ +70 (Refer to "Derating Curve") 20 ~ 95% RH non-condensing -40 ~ +80 0.03%/ , 10 ~ 95% RH (0 ~ 50 ) SAFETY STANDARDS UL8750, TUV EN61347-1, EN61347-2-13, J61347-1, J61347-2-13, IP66 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG: >100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN61000-3-2 Class C ( 65% load) ; EN61000-3-3 PACKING 59 ~ 65V Protection type : Shut down o/p voltage, re-power on to recover VIBRATION DIMENSION 54 ~ 60V Protection type : Shut down o/p voltage, re-power on to recover 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes EMC IMMUNITY MTBF 91% 0.7A/230VAC LEAKAGE CURRENT WORKING TEMP. NOTE 24V 15.6 ~ 24V 4A OVER TEMPERATURE OTHERS CEN-100-54 0 ~ 4.8A SHORT CIRCUIT EMC CEN-100-48 4.8A VOLTAGE RANGE SAFETY & CEN-100-42 CURRENT RANGE SETUP TIME PROTECTION CEN-100-36 RATED CURRENT LOAD REGULATION INPUT CEN-100-30 IP66 I/P-FG:1.88KVAC O/P-FG:0.5KVAC Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria A 519.5Khrs min. MIL-HDBK-217F (25 193*62.5*40.5mm (L*W*H) 0.6Kg; 24pcs/15.4Kg/1.11CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. Constant current operation region is within 65% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. File Name:CEN-100-SPEC 2011-07-28 CEN-100 100W Single Output LED Power Supply Mechanical Specification Case No. 993A series Unit:mm 193 10.5 172 7.6 300 20 T case SJTW 18AWG 3C 86 300 20 Vo Io ADJ. ADJ. 31.25 30.6 45 62.5 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) +V(Red) -V(Black) SVT 18AWG 2C 30.64 4.6 4PL 40.5 T case: Max. Case Temperature. Block Diagram fosc : 42KHz(115VAC) 68KHz(230VAC) EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING FG +V -V DETECTION CIRCUIT O.L.P. PWM & PFC CONTROL O.C.P. O.V.P. Derating Curve Static Characteristics 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -30 -25 -5 0 15 30 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 295 INPUT VOLTAGE (V) 60Hz File Name:CEN-100-SPEC 2011-07-28 CEN-100 100W Single Output LED Power Supply series Power Factor Characteristic Constant Current Mode PF 1 .0 0 0 .9 8 0 .9 6 0 .9 4 0 .9 2 0 .9 0 0 .8 8 0 .8 6 0 .8 4 0 .8 2 0 .8 0 0 .7 8 2 7 7 V ac 2 3 0 V ac 1 1 5 V ac 50% 60% 70% 80% 90% 100% (100W) LOAD EFFICIENCY vs LOAD (48V Model) CEN-100 series possess superior working efficiency that up to 91% can be reached in field applications. 94 EFFICIENCY (%) 90 86 82 78 74 277Vac 230Vac 70 115Vac 66 62 58 54 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. Vo(%) 100 (B) Constant Current area (A) Constant Voltage area 65 (max.) (C) Hiccup Protection 50 100 Io (%) Typical LED power supply I-V curve File Name:CEN-100-SPEC 2011-07-28