OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Features: Choice of four output options in low-cost side-looking package Choice of two sensitivity options (OPL560/561/562/563) High noise immunity Direct TTL/LSTTL CMOS interface Data rates to 250 kBaud for all except OPL560 series (200 kBaud) Low power consumption RoHS Description: All components in this series include a photodiode, amplifier, voltage regulator, Schmitt trigger and NPN output transistor on a single silicon chip. OPL560 chips also include a voltage regulator on the chip. All devices in the series have a Photologic® chip that is encapsulated in a molded plastic side-looking package with an integral lens (recessed integral lens for OPL535 and OPL536). This packaging provides enhanced optical coupling, combined with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each device offers high immunity to noise on input and VCC. OPL530, OPL531, OPL535 and OPL536 include a 10 K Ω pull-up resistor (RL) from output to VCC. These components exhibit very stable performance over supply voltages ranging from 4.5 V to 16 V and a wide range of irradiance levels. OPL550 and OPL551 devices feature TTL/LSTTL compatible logic level output which can drive up to 8 TTL loads without additional circuitry and medium-speed data rates to 250 kBaud, with typical rise and fall times of 25 nanoseconds. OPL560, OPL561, OPL562 and OPL563 devices feature TTL/LSTTL compatible logic level output which can drive up to 10 TTL loads over supply voltages ranging from 4.5 V to 16 V. OPL530, OPL531, OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 are mechanically and spectrally matched to OP140 and OP240 LEDs. OPL535 and OPL536 are mechanically and spectrally matched to OP145 and OP245 series LEDs. Applications: Non-contact reflective object sensor, Assembly line automation, Machine automation, Machine safety, End of travel sensor, Door sensor Base Part Number OPL530, OPL530-OC OPL531A, OPL531-OCA OPL535A, OPL535B OPL536A, OPL536-OC, OPL536-OCA Package External Lens Recessed Lens Output Type - with Light Input Power Range (mW/cm2) [Min/Max] - A B 0.08/0.40 0.08/0.25 Internal 10K - High Internal 10K - Low Internal 10K - High 0.20/0.40 Internal 10K - Low OPL550, OPL550A, OPL550-OC, OPL550-OCA Totem Pole - High 0.25/2.4 0.25/1.4 OPL551A, OPL551-OC, OPL551-OCA Totem Pole - Low 0.25/2.5 0.25/1.5 0.09/0.55 0.09/0.36 N/A 0.025/0.23 0.025/0.14 N/A OPL560, OPL560A, OPL560-OCA OPL561, OPL561-OC, OPL561-OCA External Lens Totem Pole - High Totem Pole - Low OPL562, OPL562A, OPL562-OC, OPL562-OCA Totem Pole - High OPL563, OPL563-OC, OPL563-OCA Totem Pole - Low N/A OC = Open Collector Output General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 1 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL550, OPL560 Series DIMENSIONS ARE IN: [ MILLIMETERS] INCHES Pin # Sensor 1 Ground Pin # Sensor 2 Output 1 Ground 3 VCC 2 Output 3 Vcc OPL535, OPL536 Series DIMENSIONS ARE IN: Pin # Sensor 1 Ground 2 3 General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc [ MILLIMETERS] INCHES Pin # Sensor Output 1 Ground VCC 2 Output 3 Vcc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 2 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 (-OC, -OCA, -OCB) OPL550, OPL550A, OPL551A, OPL560, OPL560A, OPL561, OPL562, OPL562A, OPL563, OPL563A OPL550/550A/560/560A/562/562A Totem-Pole OPL530/535/550/560/562 (-OC, -OCA, -OCB) Open-Collector VCC VCC OUT OUT GND OPL 551A/561/563/563A Inverted Totem-Pole GND OPL 531/536/551/561/563 (-OC, -OCA, -OCB) Inverted Open-Collector VCC VCC OUT OUT GND General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc GND OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 3 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 OPL530, OPL531A, OPL535A, OPL535B, OPL536, OPL536A OPL530, OPL535A/535B 10K Pull-Up OPL531A, OPL536/536A Inverted 10K Pull-Up VCC VCC OUT OUT GND GND VCC VCC OUT OUT GND General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc GND OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 4 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Absolute Maximum Ratings (TA = 25° C unless otherwise noted) Input Diode Supply Voltage (VCC) OPL530, OPL530-OC, OPL536-OC, OPL550 OPL560, OPL561, OPL562, OPL563 18 V 10 V 18 V Operating Temperature Range -40° C to + 85° C Storage Temperature Range -40° C to + 100° C Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] 260°C Sourcing Current OPL560, OPL561, OPL562, OPL563 10 mA Power Dissipation OPL530, OPL530-OC, OPL536-OC OPL550, OPL560, OPL561, OPL562, OPL563 90 mW 200 mW(2) Sinking Current OPL530, OPL530-OC, OPL536-OC OPL550 OPL560, OPL561, OPL562, OPL563 50 mA 50 mA Voltage at Output Lead (4) OPL530, OPL530-OC, OPL536-OC OPL550-OC, OPL551-OC OPL561-OC, OPL562-OC, OPL563-OC 35 V 35 V 35 V Duration of Output Short to VCC or Ground OP550 1 second Duration of Output Short to VCC OPL550-OC, OPL551-OC OPL560, OPL561, OPL562, OPL563, OPL561-OC, OPL562-OC, OPL563-OC 1 second 1 second Low Level Output Current OPL550, OPL551 Series 16 mA High Level Output Current OPL550, OPL551 Series 1 mA Irradiance OPL550, OPL551 Series OPL560, OPL561, OPL561-OC OPL562, OPL562-OC, OPL563, OPL563-OC 10 mW/cm2 9 mW/cm 3 mW/cm2 Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 5 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS 4.5 - 16 V - 4.5 - 5.5 - - 2 - 2 - - 2.7 5 mA EE = 0 or 1 mW/cm2 OPL550, OPL551 Series - 8 15 mA EE = 0 or 3 mW/cm2, VCC = 5.5 V OPL560, OPL561 Series - 8 12 mA EE = 0 or 1 mW/cm2 0.08 - 0.40 mW/cm2 TA = 25° C OPL531A, OPL531-OCA OPL535A, OPL536A, OPL536-OCA 0.08 - 0.25 mW/cm2 TA = 25° C OPL535B 0.12 - 0.40 mW/cm2 TA = 25° C OPL550, OPL550-OC, OPL551-OC OPL550A, OPL550-OCA, OPL551-OCA .25 .25 - 2.4 1.4 mW/cm2 VCC = 5 V, TA = 25° C mW/cm2 VCC = 5 V, TA = 25° C Operating Supply Voltage OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC, OPL560, OPL561 Series OPL550, OPL551 Series VCC Peak-to-Peak VCC Ripple Necessary to Cause False Triggering of Output OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC OPL560, OPL561 Series OPL550, OPL551 Series Supply Current(4) OPL530, OPL530-OC OPL536-OC V - V f = DC to 50 MHz V VCC = 5 V DC, f = DC to 50 MHz ICC Positive-Going Threshold Irradiance(3) OPL530, OPL530-OC OPL536-OC EeT(+) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 6 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Hysteresis Ratio OP530, OP531 Series 1.05 1.3 1.6 - - OP535, OP536 Series 1.05 1.2 1.5 - - OPL550, OPL551 Series 1.50 2 2.5 - - OPL560, OPL561 Series 1.20 1.55 2 - - - -0.6 - %/°C >0°C - -1.6 - %/°C <0°C EeT(+)/EeT(-) ∆Eet(+)(∆T) Temperature Co-efficient OPL530, OPL530-OC OPL536-OC Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 7 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS 2.4 3.3 - V VCC = 4.5 V, IOH = -800 µa, EE = 3 mW/cm2 OPL560 VCC -2.1 - - V IOH = -1 µA, EE = 1 mW/cm2 OPL561 VCC -2.1 - - V IOH = -1 µA, EE = 0 - 0.2 0.4 V IOL = 16 mA, EE = 0 OPL536-OC - 0.2 0.4 V IOL = 16 mA, EE = 1 mW/cm2 OPL550 - 0.25 0.4 V VCC = 4.5 V, IOL = 12.8 mA, EE = 0 OPL560 - - .4 V IOL = 16 mA, EE = 0 OPL561, OPL561-OC - - .4 V IOL = 16 mA, EE = 1 mW/cm2 Short Circuit Output Current OPL550 -20 -55 -100 mA VCC = 5.5 V, Output = GND, EE = 3 mW/cm2 High Level Output Current(4) OPL536-OC - 0.1 10 µA VOH = 30 V, EE = 0 OPL530, OPL530-OC - 0.1 10 µA VOH = 30 V, EE = 1 mW/cm2 OPL550-OC - 1 100 µA OPL551-OC - 1 100 µA VCC = 4.5 V, VOH = 30 V, EE = 3 mW/cm2 VCC = 4.5 V, VOH = 30 V, EE = 0 OPL561-OC - - 100 µA Operating Supply Voltage OPL550 TEST CONDITIONS VOH Low Level Output Voltage OPL530, OPL530-OC VOL IOS IOH VOH = 30 V, EE = 0 Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 8 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER Output Rise Time OPL530 MIN TYP MAX UNITS - 1.5 - µs EE = 0 or 1 mW/cm2, CL = 50 pF - 50 - ns - 25 70 ns OPL550-OC, OPL551-OC - 25 70 ns OPL560, OPL561 - - 70 ns OPL561-OC - - 100 µs EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 Pf VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, f = 10 kHz, DC = 50% RL = 8 TTL loads VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, f = 10 kHz, DC = 50%, RL = 360 Ω TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz, DC = 50%, RL = 360 Ω - - - µs EE = 0 or 1 mW/cm2, CL = 50 pF OPL530-OC, OPL536-OC - - - ns EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF OPL550-OC, OPL551-OC - 25 70 ns OPL561-OC - - 70 ns OPL560, OPL561 - - 70 ns OPL561-OC - - 100 ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz - 20 - ns EE = 0 or 1 mW/cm2, CL = 50 Pf OPL530-OC, OPL536-OC - 20 - ns EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF OPL550-OC, OPL551-OC - 25 70 ns OPL560, OPL561 - - 70 ns OPL561-OC - - 100 ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 360 Ω, f = 10 kHz, DC = 50% TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz TA = 25° C, EE = 0 or 1 mW/cm2, f = 10 kHz OPL530-OC, OPL536-OC OPL550 tr Output Rise Time OPL530 tr Output Fall Time OPL530 tf Notes: (1) (2) (3) (4) TEST CONDITIONS RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560, OPL561, OPL562 and OPL563 series. Irradiance measurements are made with λi = 935 nm. This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 9 OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS - 1.0 - µs - 1.0 - µs - 2.5 5 µs EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V, CL = 50 pF VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% - 3.0 - µs EE= 0 or 1 mW/cm2, RL = 300 Ω to 5V, CL = 50 pF - 2.5 5 µs VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2, RL = 360 Ω, f = 10 kHz, DC = 50% - 5 - µs DC = 50%, RL = 10 TTL Loads - 5 - µs DC = 50%, RL = 300 Ω Propagation Delay OPL530 OPL530-OC, OPL536-OC tpEeT(+) OPL550-OC, OPL551-OC tpEeT(-) Propagation Delay OPL530, OPL530-OC, OPL536-OC OPL550-OC, OPL551-OC tPLH, TPHL Propagation Delay (Low-High/High-Low) OPL560, OPL561 OPL561-OC Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL536, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with λi = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue C 09/2016 Page 10