MPQ4569-AEC1 75V, 0.3A Synchronous Step-Down Converter AEC-Q100 Qualified FEATURES DESCRIPTION The MPQ4569 is a step-down switching regulator with integrated high-side/low-side, high-voltage power MOSFETs. It provides a highly efficient output of up to 0.3A. The wide 4.5V to 75V input range accommodates a variety of step-down applications in automotive environment. A 5μA shutdown mode quiescent current in full temperature range is good for battery-powered applications. It allows for high power conversion efficiency over a wide load range by scaling down the switching frequency under light-load condition to reduce the switching and gate driver losses. 20μA Quiescent Current (Active mode) Wide 4.5V to 75V Operating Input Range 1.2Ω/0.45Ω Internal Power MOSFETs Programmable Soft-Start FB-Tolerance: 1% at Room Temperature; 2% at Full Temperature. Adjustable Output Voltage 1V Reference Voltage Output for QFN Package Low Shutdown Mode Current: 5μA Available in QFN-10 (3mmx3mm) and SOIC-8 EP Packages Available in AEC-Q100 Grade 1 APPLICATIONS The switching frequency during start-up and short circuit also can be scaled down to prevent inductor current runaway. Thermal shutdown provides reliable, fault-tolerant operation. Automotive Systems Industrial Power Systems Distributed Power Systems Battery Powered Systems All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. The MPQ4569 is available in QFN-10 (3mmx3mm) and SOIC-8 EP packages. “MPS” and “The Future of Analog IC Technology” are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION 2 7 VIN C1 10uF 100V SW GND 5 SS FB 6 C3 0.1uF C1 10uF 100V EN 3 VREF 4 BST VIN R1 1.2M C4 39pF R2 523K U1 2 BIAS 4 9 GND VOUT GND BIAS EN C5 10nF 4.5V-75V 3.3V/300mA C2 47uF 10V 1 3 VIN L1 33uH 8 MPQ4569GN GND EN C3 0.1uF BST U1 4.5V-75V VIN SW L1 33uH VOUT C2 47uF 10V MPQ4569GQ EN GND BIAS VREF FB 8 BIAS R1 1.2M 5 C4 39pF SS POK 7 POK 1 6 GND R2 523K C5 10nF 3.3V/300mA 10 MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 1 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER ORDERING INFORMATION Part Number* Package Top Marking QFN-10 (3mmx3mm) See Below SOIC-8 EP See Below MPQ4569GQ MPQ4569GQ-AEC1 MPQ4569GN MPQ4569GN-AEC1 * For Tape & Reel, add suffix –Z (e.g. MPQ4569GQ–Z) TOP MARKING (QFN-10 (3mmx3mm)) AEX: product code of MPQ4569GQ; Y: year code; LLL: lot number; TOP MARKING (SOIC-8 EP) MP4569: part number: LLLLLLLL: lot number; MPS: MPS prefix: Y: year code; WW: week code: MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 2 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER PACKAGE REFERENCE QFN-10 (3mmx3mm) SOIC-8 EP ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance Supply Voltage (VIN) ………… ..... -0.3V to +80V Switch Voltage (VSW) …… …….-0.3V to VIN + 1V BST to SW…………………………-0.3V to +6.0V All Other Pins……………… . ……-0.3V to +6.0V EN Sink Current ………………..........……150μA (2) Continuous Power Dissipation (TA = +25°C) QFN-10 (3mmx3mm)…………………….......2.5W SOIC-8 EP ……..…………………..…………2.6W Junction Temperature………… .. …………150C Lead Temperature ………… ...... …………260C Storage Temperature…………. -65°C to +150C QFN-10 (3mmx3mm) …………50……12…C/W SOIC-8 EP ……..………………48……12…C/W Recommended Operating Conditions (3) Supply Voltage VIN ………… ........... 4.5V to 75V Output Voltage VOUT .. …………1V to 0.9xVIN Operating Junction Temp. (TJ). -40°C to +125°C (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD (MAX) = (TJ (MAX)-TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7, 4-layer PCB. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 3 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER ELECTRICAL CHARACTERISTICS VIN = 24V, VEN = 2V, TJ = - 40C to +125C, unless otherwise noted. Typical values are at TJ=+25°C. Parameter Condition Supply Quiescent Current Shutdown Supply Current VIN UVLO Rising Threshold No load, VFB=1.2V VEN < 0.3V VIN UVLO Falling Threshold VIN UVLO Hysteresis Feedback Voltage Feedback Current (5) VREF Pin Voltage Upper Switch On Resistance Lower Switch On Resistance Lower Switch Leakage Min Typ Max Units 3.9 20 2.2 4.2 30 5 4.4 μA μA V 3.75 0.45 1 3.95 1.01 1.02 50 1.035 V V V V nA V 0.45 1.5 2.5 0.625 0.9 1 Ω Ω Ω Ω μA 720 810 mA 3.45 VIN=4.5V to 75V, TJ=25 °C VIN=4.5V to 75V, VFB=1.2V VIN=4.5V to 75V, IREF=100μA 0.99 0.98 -50 0.965 VBST-VSW =5V, TJ=25 °C VBST-VSW =5V, VBIAS=5V, TJ=25 °C VBIAS=5V VEN = 0V, VSW = 75V 0.9 0.7 0.275 0.2 Peak Current Limit 630 (6) Minimum Switch On Time Enable Rising Threshold Enable Falling Threshold Enable Threshold Hysteresis Enable Current Soft Start Current (5) POK Upper Trip Threshold (5) POK Lower Trip Threshold (5) POK Threshold Hysteresis (5) POK Deglitch Timer (5) POK Output Voltage Low FB OVP Rising Threshold 1.25 1.152 VEN=2.4V 4 FB respect to the nominal value FB respect to the nominal value FB respect to the nominal value 1.2 120 1.55 1.2 0.35 0.8 5.5 1.85 1.248 90 85 5 40 ISINK = 1mA FB OVP Hysteresis Thermal Shutdown 86 81 2 1 (6) Thermal Shutdown (6) Hysteresis 1.05 7 94 89 0.4 1.1 ns V V V μA μA % % % μs V V 50 mV 175 C 20 C Notes: 5) QFN package only. 6) Derived from bench characterization. Not tested in production. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 4 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER PIN FUNCTIONS Pin # QFN-10 (3mmx3mm) Pin # SOIC-8 EP Name Description 1 1 GND Ground. Connected the output capacitor as close as possible to avoid high-current switch paths. 2 2 IN Input Supply. Requires a decoupling capacitor to ground to reduce switching spikes. 3 3 EN Enable Input. Pull this pin below the low threshold to shut the chip down. Pull it above the high threshold enables the chip. Float this pin to shut the chip down. 4 No Bonding VREF 5 4 FB 6 5 SS 7 No Bonding POK 8 6 BIAS 9 7 BST 10 8 SW Reference Voltage Output, for QFN-10 (3mmx3mm) package only. Feedback Connected to the tap of an external resistive divider between the output and GND. Sets the regulation voltage when compared to the internal 1V reference. Soft-Start Control Input. Connect a capacitor from SS to GND to set the soft-start period. Open Drain Power Good Output. “HIGH” output indicates VOUT is higher than 90% of reference. POK is pulled down in shutdown, for QFN-10 (3mmx3mm) package only Controller Bias Input. Supplies current to the internal circuit when VBIAS>2.9V. Bootstrap. Positive power supply for the internal floating high-side MOSFET driver. Connect a bypass capacitor between this pin and SW pin. Switch Node. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 5 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER TYPICAL CHARACTERISTICS VIN=12V, unless otherwise noted. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 6 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS VIN = 12V, VOUT = 3.3V, L = 33µH, COUT=2x22μF, TA = +25°C, unless otherwise noted. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 7 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 12V, VOUT = 3.3V, L = 33µH, COUT=2x22μF, TA = +25°C, unless otherwise noted. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 8 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER FUNCTIONAL BLOCK DIAGRAM VIN BIAS BST REGULATOR REF VREF EN ICOMP EN Control + 3M ILIMIT POK POK + + SS - S RS R COMP SS - SW ZCD FB GND Figure 1 - Functional Block Diagram MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 9 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER OPERATION The MPQ4569 is a 75V, 0.3A, synchronous, step-down switching regulator with integrated high-side and low-side high-voltage power MOSFETs (HS_FET and LS_FET, respectively). It provides a highly-efficient, 0.3A output. It features a wide input voltage range, external softstart control, and precision current limit. Its very low operational quiescent current makes it suitable for battery-powered applications. Control Scheme The ILIM comparator, FB comparator and zero current detector (ZCD) block control the PWM. If VFB is below the 1V reference and the inductor current drops to zero, HS_FET turns on and the ILIM comparator starts to sense the HS_FET current: When the HS_FET current reaches the limit, the HS_FET turns off and LS_FET turns on together with the ZCD block. Meanwhile, the ILIM comparator is turned off to reduce the quiescent current. The LS_FET turns off together with ZCD block after the inductor current drops to zero. If VFB is less than the 1V reference at this time, the HS_FET turns on at once and commences another cycle. If VFB is still higher than 1V reference, HS_FET would not turn on till VFB drops below 1V. VFB VREF VSW IL Ipeak Io Io increase Internal Regulator and BIAS The 2.6V internal regulator powers most of the internal circuitry. This regulator takes VIN and operates in the full VIN range. When VIN is greater than 3.0V, the output of the regulator is in full regulation. Lower values of VIN result in lower output voltages. When VBIAS>2.9V, the bias supply overrides the input voltage and supplies power to the internal regulator. When VBIAS>4.5V, it can power LS_FET driver furthermore. Using BIAS to power internal regulator can improve the efficiency. It is recommended to connect BIAS to the regulated output voltage when it is in the range of 2.9V to 5.5V. When output voltage is out of above range, an external supply that is >2.9V or even better >4.5V can be used to power BIAS. Enable Control The MPQ4569 has a dedicated enable-control pin, EN: when VIN goes high, the EN pin enables and disables the chip. This is HIGH logic. Its trailing threshold is a consistent 1.2V. Its rising threshold is about 350mV higher. When floating, EN pin is internally pulled down to GND to disable the chip. When EN = 0V, the chip goes into the lowest shutdown-current mode. When EN is higher than zero but lower than its rising threshold, the chip remains in shutdown mode with a slightly larger shutdown current. Internally a zener diode is connected from EN pin to GND pin. The typical clamping voltage of the zener diode is 6.5V. So VIN can be connected to EN through a high ohm resistor if the system doesn't have another logic input acting as enable signal. The resistor needs to be designed to limit the EN pin sink current less than 150μA. Just note that there is an internal 3M resistor from EN to GND, so the external pull up resistor should be smaller than [VIN (MIN) - 1.55V] 3M to make sure 1.55V the part can EN on at the lowest operation VIN. Figure2 - Control Scheme MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 10 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER Under-Voltage Lockout VIN under voltage lockout (UVLO) protects the chip from operating below the operational supply voltage range. The UVLO-rising threshold is about 4.2V while its trailing threshold is about 3.75V. Soft-start Reference-type soft-start prevents the converter output voltage from overshooting during startup. When the chip starts, the internal circuitry generates a constant current to charge external SS capacitor. The soft-start (SS) voltage slowly ramps up from 0V at a slow pace set by the softstart time. When VSS is less than the VREF, VSS overrides VREF so the FB comparator uses VSS instead of VREF as the reference. When VSS is higher than VREF, VREF resumes control. VSS is also associated with VFB. Though VSS can be much smaller than VFB, it can only barely exceed VFB. If somehow VFB drops, VSS tracks VFB. This function prevents output voltage overshoot in short-circuit recovery -- when the short circuit is removed, the SS ramps up as if it is a fresh soft-start process. Thermal Shutdown Thermal shutdown prevents the chip from thermally running away. When the silicon die temperature exceeds its upper threshold, the thermal shutdown feature shuts down the whole chip. When the temperature falls below its lower threshold, the chip resumes function. Floating Driver and Bootstrap Charging The external bootstrap capacitor powers the floating HS_FET driver. This floating driver has its own UVLO protection, with a rising threshold of about 2.4V with a hysteresis of about 300mV. During this UVLO, the SS voltage resets to zero. When the UVLO is disabled, the regulator follows the soft-start process. The dedicated internal bootstrap regulator charges and regulates the bootstrap capacitor to about 5V. When the voltage difference between BST and SW falls below its working parameters, a PMOS pass transistor connected from VIN to BST turns on to charge the bootstrap capacitor. The current path is from VIN to BST and then to SW. The external circuit must have enough voltage headroom to accommodate charging. As long as VIN is sufficiently higher than SW, the bootstrap capacitor can charge. When the HS_FET is ON, VIN is about equal to SW so the bootstrap capacitor cannot charge. The best charging period occurs when the LS_FET is on so that VIN - VSW is at its largest. When there is no current in the inductor, VSW equals VOUT so the difference between VIN and VOUT can charge the bootstrap capacitor. If the internal circuit does not have sufficient voltage and time to charge the bootstrap capacitor, extra external circuitry can be used to ensure the bootstrap voltage in normal operation region. Startup and Shutdown If both VIN and VEN are higher than their appropriate thresholds, the chip starts operating. The reference block starts first, generating stable reference voltage and currents, and then enables the internal regulator. The regulator provides stable supply for the rest device. While the internal supply rail is high, an internal timer holds the power MOSFET off for about 50µsec to blank startup glitches. When the softstart block is enabled, it first holds its SS output low and then slowly ramps up. Three events shut down the chip: VEN low, VIN low, and junction temperature triggers the thermal shutdown threshold. For shutdown, the signaling path is blocked first to avoid any fault triggering. Internal supply rail is pulled down then. The floating driver is not subject to this shutdown command, but its charging path is disabled. Power OK (POK) POK is an open drain power good output. “HIGH” output indicates VOUT is higher than 90% of its nominal value. POK is pulled down in shutdown mode. Reference Voltage Output (VREF) VREF pin output 1V reference voltage. It has up to 500uA source current capability. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 11 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER APPLICATION INFORMATION To get the desired output voltage, divider resistor Selecting the Inductor VOUT As the Ipeak is fixed, for given input voltage and output voltage, the inductor value can be determined by the following formula: R4 L VOUT VIN - VOUT VIN Ipeak fs Where fs is the switching frequency at the maximal output current. Larger inductor value results in lower switching frequency, as well as higher efficiency. However, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current as well as the slow load transient dynamic performance. There is also a lower limit of the inductor value, which is determined by the minimum on time. In order to keep the inductor working under control, the inductor value should be chosen higher than Lmin that is derived from below formula: L MIN VIN (MAX ) t ON(MIN) Ipeak Where VIN(MAX) is the max value of input voltage. tON(MIN) is the 120ns minimum switch on time. Switching Frequency Switching frequency can be estimated by below equation. fs 2 Io VOUT VIN - VOUT 2 Ipeak VIN L Larger inductor can get lower fs. And fs increases as Io increasing. When Io increases to its maximal value Ipeak/2, fs also reaches its highest value and can be derived by: fs(max) VOUT VIN - VOUT Ipeak VIN L Setting the Output Voltage The output voltage is set using a resistive voltage divider from the output voltage to FB pin. As shown in figure 3. FB R5 Figure 3 – Adjustable VOUT by divider resistors can be chosen through below formula: R4 VOUT -1 R5 VREF Where VREF is the FB reference voltage 1V. The current flows into divider resistor would increase the supply current, especially at no load and light load condition. The Vin supply current caused by the feedback resistors can be calculated from: IIN_FB VOUT V 1 OUT R4 R5 VIN η Where η is the efficiency of the regulator. To reduce this current, resistors in the megohm range are recommended. The recommended value of the feedback resistors are shown in Table 1. Table 1—Resistor Selection for Common Output Voltages VOUT (V) R4 (kΩ) R5 (kΩ) 3.3 5 1200 1200 523 300 Under Voltage Lock Out Point Setting MPQ4569 has internal fixed under voltage lock out (UVLO) threshold: rising threshold is about 4.2V while trailing threshold is about 3.75V. External resistor divider between EN and VIN as shown in Figure 4 can be used to get higher equivalent UVLO threshold. VIN IN R1 R2 EN 3M Figure 4 – Adjustable UVLO using EN pin MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 12 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER The UVLO threshold can be computed from below two equations. R1 ) ENTH_Rising 3M//R2 R1 UVLO TH_Falling (1 ) ENTH_Falling 3M//R2 UVLO TH_Rising (1 5) For better thermal performance and long-term reliability consideration, VIN, SW and GND should be connected to a large copper area respectively to cool the chip. Soft Start Capacitor The soft start time is the duration when SS is charged from 0 to FB reference voltage 1V by an internal 5μA current source. So the capacitor at SS pin can be chosen according to below formula: CSS 5 t SS (μF) Feedforward Capacitor As described above that the PWM control scheme of MPQ4569 is very special and the HS_FET turns on when FB drops lower than reference voltage. This brings good load transient performance. However, this also makes the HS_FET turn on moment is very sensitive to the FB voltage. Once there is noise on FB, the moment HS_FET turns on is easy to be affected, and then Fsw jitter would occur. The Fsw jitter is easy to happen especially when Vo ripple is very small. To improve the jitter performance, a small feedforward capacitor between Vo and FB can be used and typical 39pF is recommended. Top Layer PCB Layout PCB layout is very important to achieve stable operation. Please follow below guidelines and use Figure 5 as reference. 1) Keep the path of switching current short and minimize the loop area formed by input capacitor, high-side, low-side MOSFET and output capacitor. 2) Bypass ceramic capacitors should be as close as possible to the VIN pin. 3) Make sure that all feedback connections are short and direct. Place the feedback resistors as close to the chip as possible. 4) Keep SW away from sensitive analog areas such as FB. Bottom Layer 1) Layout Reference of QFN-10 Package(7) MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 13 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER Top Layer Bottom Layer 2) Layout Reference of SOIC-8 EP Package(8) Figure 5 – Layout Reference Notes: 7) Take Figure 6 as schematic 8) Take Figure 7 as schematic MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 14 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER TYPICAL APPLICATION CIRCUITS C3 0.1uF U1 4.5V-75V 2 VIN R1 1M C1A 10uF 100V C1B 0.1uF 100V GND 3 VIN L1 33uH 9 BST SW 3.3V/300mA 10 VOUT C2 22uF 16V MPQ4569GQ EN GND BIAS R3 8 10 R2 NS C4 0.1uF 4 VREF FB R4 1.2M 5 C7 1uF C5 R5 523K 39pF R6 100K 6 SS GND POK 7 1 C6 10nF Figure 6 – 3.3V Output Typical Application Circuit of QFN-10 Package C3 0.1uF U1 4.5V-75V 2 VIN R1 1M C1A 10uF 100V C1B 0.1uF 100V GND 3 VIN L1 33uH 7 BST SW 3.3V/300mA 8 VOUT C2 22uF 16V MPQ4569GN EN BIAS GND R3 6 10 R2 NS C4 0.1uF 5 C6 10nF FB SS GND 1 R4 1.2M 4 R5 523K C5 39pF Figure 7 – 3.3V Output Typical Application Circuit of SOIC-8 EP Package MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 15 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER PACKAGE INFORMATION QFN-10 (3mmx3mm) MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 16 MPQ4569―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER SOIC-8 EP NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MPQ4569 Rev. 1.02 www.MonolithicPower.com 5/25/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 17