MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER • DESCRIPTION The 38B5 group is the 8-bit microcomputer based on the 740 family core technology. The 38B5 group has six 8-bit timers, a 16-bit timer, a fluorescent display automatic display circuit, 12-channel 10-bit A-D converter, a serial I/O with automatic transfer function, which are available for controlling musical instruments and household appliances. The 38B5 group has variations of internal memory size and packaging. For details, refer to the section on part numbering. For details on availability of microcomputers in the 38B5 group, refer to the section on group expansion. • • • • • • • FEATURES • Basic machine-language instructions ....................................... 71 • The minimum instruction execution time .......................... 0.48 µs (at 4.19 MHz oscillation frequency) • Memory size • • • • • • • ROM ............................................. 24K to 60K bytes RAM ............................................ 512 to 2048 bytes Programmable input/output ports ............................................. 55 High-breakdown-voltage output ports ....................................... 36 Software pull-up resistors ...... (Ports P5, P61 to P65, P7, P84 to P87, P9) Interrupts .................................................. 21 sources, 16 vectors Timers ........................................................... 8-bit ✕ 6, 16-bit ✕ 1 Serial I/O1 (Clock-synchronized) .................................... 8-bit ✕ 1 ...................... (max. 256-byte automatic transfer function) Serial I/O2 (UART or Clock-synchronized) ..................... 8-bit ✕ 1 • • PWM ............................................................................. 14-bit ✕ 1 8-bit ✕ 1 (also functions as timer 6) A-D converter .............................................. 10-bit ✕ 12 channels Fluorescent display function ........................ Total 40 control pins Interrupt interval determination function ..................................... 1 Watchdog timer ............................................................. 20-bit ✕ 1 Buzzer output ............................................................................. 1 2 Clock generating circuit Main clock (XIN–XOUT) ......................... Internal feedback resistor Sub-clock (XCIN–XCOUT) ......... Without internal feedback resistor (connect to external ceramic resonator or quartz-crystal oscillator) Power source voltage In high-speed mode ................................................... 4.0 to 5.5 V (at 4.19 MHz oscillation frequency and high-speed selected) In middle-speed mode ............................................... 2.7 to 5.5 V (at 4.19 MHz oscillation frequency and middle-speed selected) In low-speed mode .................................................... 2.7 to 5.5 V (at 32 kHz oscillation frequency and low-speed selected) Power dissipation In high-speed mode .......................................................... 35 mW (at 4.19 MHz oscillation frequency) In low-speed mode ............................................................ 60 µW (at 32 kHz oscillation frequency, at 3 V power source voltage) Operating temperature range ................................... –20 to 85 °C APPLICATION Musical instruments, VCR, household appliances, etc. 50 49 48 47 46 45 44 43 42 41 40 65 66 67 39 38 68 37 69 36 70 35 71 34 33 72 M38B57MC-XXXFP 73 32 74 31 75 30 76 29 77 28 78 27 79 80 26 21 22 23 24 13 14 15 16 17 18 19 20 11 12 4 5 6 7 8 9 10 P75/AN5 P74/AN4 P73/AN3 P72/AN2 P71/AN1 P70/AN0 P61/CNTR0/CNTR2 P60/CNTR1 P47/INT2 RESET P91/XCOUT P90/XCIN Vss XIN XOUT Vcc P46/T3OUT P45/T1OUT P44/PWM1 P43/BUZ01 P42/INT3 P41/INT1 P40/INT0 P87/PWM0/FLD39 2 3 25 1 P57/SRDY2/SCLK22 P56/SCLK21 P55/TxD P54/RxD P53/SCLK12 P52/SCLK11 P51/SOUT1 P50/SIN1 AVSS VREF P65/SSTB1/AN11 P64/INT4/SBUSY1/AN10 P63/AN9 P62/SRDY1/AN8 P77/AN7 P76/AN6 62 61 60 59 58 57 56 55 54 53 52 51 64 63 P20/BUZ02/FLD0 P21/FLD1 P22/FLD2 P23/FLD3 P24/FLD4 P25/FLD5 P26/FLD6 P27/FLD7 P00/FLD8 P01/FLD9 P02/FLD10 P03/FLD11 P04/FLD12 P05/FLD13 P06/FLD14 P07/FLD15 P10/FLD16 P11/FLD17 P12/FLD18 P13/FLD19 P14/FLD20 P15/FLD21 P16/FLD22 P17/FLD23 PIN CONFIGURATION (TOP VIEW) Package type : 80P6N-A 80-pin plastic-molded QFP Fig. 1 Pin Configuration of M38B57MC-XXXFP P30/FLD24 P31/FLD25 P32/FLD26 P33/FLD27 P34/FLD28 P35/FLD29 P36/FLD30 P37/FLD31 P80/FLD32 P81/FLD33 P82/FLD34 P83/FLD35 VEE P84/FLD36 P85/RTP0/FLD37 P86/RTP1/FLD38 2 Port P0(8) 8 Fig. 2 Functional Block Diagram A-D converter Port P7(8) 8 Port P6(6) 6 8 Interrupt interval determination function Watchdog timer 8 Port P8(8) RAM ROM Memory XIN-XOUT (main-clock) XCIN-XCOUT (sub-clock) System clock generation Port P3(8) 8 2 Port P9(2) Port P4(8) 1 7 ARY N I IM L E PR Port P5(8) (36 high-breakdown voltage ports) 40 control pins FLD display function CPU core Timer X(16-bit) Timer 1(8-bit) Timer 2(8-bit) Timer 3(8-bit) Timer 4(8-bit) Timer 5(8-bit) Timer 6(8-bit) Timers Port P2(8) 8 . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som Buzzer output PWM0(14-bit) PWM1(8-bit) Serial I/O2 (Clock-synchronized or UART) Serial I/O1(Clock-synchronized) (256 byte automatic transfer) Serial I/O (10-bit ✕ 12 channel) 8 Port P1(8) Build-in peripheral functions I/O ports FUNCTIONAL BLOCK DIAGRAM (Package : 80P6N-A) MITSUBISHI MICROCOMPUTERS 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FUNCTIONAL BLOCK MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PIN DESCRIPTION Table 1 Pin Description (1) Pin Name Function VCC, VSS Power source • Apply voltage of 4.0–5.5 V to VCC, and 0 V to VSS. VEE Pull-down • Apply voltage supplied to pull-down resistors of ports P0, P1, and P3. VREF power source Reference • Reference voltage input pin for A-D converter. Function except a port function voltage AVSS Analog power • Analog power source input pin for A-D converter. source • Connect to VSS. RESET Reset input • Reset input pin for active “L.” XIN Clock input • Input and output pins for the main clock generating circuit. • Feedback resistor is built in between XIN pin and XOUT pin. XOUT Clock output P00/FLD8– I/O port P0 ______ • Connect a ceramic resonator or quartz-crystal oscillator between the XIN and XOUT pins to set the oscillation frequency. • When an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open. • The clock is used as the oscillating source of system clock. P07/FLD15 • 8-bit I/O port. • I/O direction register allows each pin to be individually programmed as either input or output. • FLD automatic display pins • At reset, this port is set to input mode. • A pull-down resistor is built in between port P0 and the VEE pin. • CMOS compatible input level. • High-breakdown-voltage P-channel open-drain output structure. P10/FLD16– Output port P1 • At reset, this port is set to VEE level. • 8-bit output port. P17/FLD23 • A pull-down resistor is built in between port P1 and the VEE pin. • FLD automatic display pins • High-breakdown-voltage P-channel open-drain output structure. • At reset, this port is set to VEE level. P20/BUZ02/ FLD0– I/O port P2 • 8-bit I/O port with the same function as port P0. • Low-voltage input level. • FLD automatic display pins P27/FLD7 • High-breakdown-voltage P-channel open-drain output structure. • Buzzer output pin (P20) P30/FLD24– Output port P3 • 8-bit output port. • FLD automatic display P37/FLD31 • A pull-down resistor is built in between port P3 and the VEE pin. pins • High-breakdown-voltage P-channel open-drain output structure. P40/INT0, I/O port P4 • At reset, this port is set to VEE level. • 7-bit I/O port with the same function as port P0. P41/INT1, • CMOS compatible input level. P42/INT3 • N-channel open-drain output structure. • Interrupt input pins P43/BUZ01 • Buzzer output pin P44/PWM1 • PWM output pin (Timer output pin) • Timer output pin P45/T1OUT, P46/T3OUT P47/INT2 Input port P4 • 1-bit input port. • Interrupt input pin • CMOS compatible input level. 3 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 2 Pin Description (2) Pin P50/SIN1, Name I/O port P5 P51/SOUT1, P52/SCLK11, Function • 8-bit CMOS I/O port with the same function as port P0. Function except a port function • Serial I/O1 function pins • CMOS compatible input level. • CMOS 3-state output structure. P53/SCLK12 P54/RXD, P55/TXD, • Serial I/O2 function pins P56/SCLK21, ________ P57/SRDY2/ SCLK22 P60/CNTR1 I/O port P6 • 1-bit I/O port with the same function as port P0. • CMOS compatible input level. • Timer input pin • N-channel open-drain output structure. P61/CNTR0/ • 5-bit CMOS I/O port with the same function as port P0. CNTR2 • CMOS compatible input level. • Timer I/O pin ________ P62/SRDY1/ • CMOS 3-state output structure. AN8 P63/AN9 • Serial I/O1 function pin • A-D conversion input pin • A-D conversion input pin P64/INT4/ • Serial I/O1 function pin SBUSY1/AN10, • A-D conversion input pin P65/SSTB1/ • Interrupt input pin (P64) AN11 P70/AN0– P77/AN7 I/O port P7 • 8-bit CMOS I/O port with the same function as port P0. • CMOS compatible input level. • A-D conversion input pin • CMOS 3-state output structure. P80/FLD32– I/O port P8 P83/FLD35 • 4-bit I/O port with the same function as port P0. • Low-voltage input level. • FLD automatic display pins • High-breakdown-voltage P-channel open-drain output structure. P84/FLD36 P85/RTP0/ FLD37, P86/RTP1/ • 4-bit CMOS I/O port with the same function as port P0. • Low-voltage input level. FLD38 P87/PWM0/ FLD39 P90/XCIN, P91/XCOUT 4 • FLD automatic display pins • FLD automatic display pins • 14-bit PWM output I/O port P9 • 2-bit CMOS I/O port with the same function as port P0. • I/O pins for sub-clock generating • CMOS compatible input level. circuit (connect a ceramic resona- • CMOS 3-state output structure. tor or a quarts-crystal oscillator) MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PART NUMBERING Product M38B5 7 M C - XXX FP Package type FP : 80P6N-A package FS : 80D0 package ROM number Omitted in some types. ROM/PROM size 1 : 4096 bytes 2 : 8192 bytes 3 : 12288 bytes 4 : 16384 bytes 5 : 20480 bytes 6 : 24576 bytes 7 : 28672 bytes 8 : 32768 bytes 9 : 36864 bytes A : 40960 bytes B : 45056 bytes C : 49152 bytes D : 53248 bytes E : 57344 bytes F : 61440 bytes The first 128 bytes and the last 2 bytes of ROM are reserved areas ; they cannot be used for users. Memory type M : Mask ROM version E : EPROM or One Time PROM version RAM size 0 : 192 bytes 1 : 256 bytes 2 : 384 bytes 3 : 512 bytes 4 : 640 bytes 5 : 768 bytes 6 : 896 bytes 7 : 1024 bytes 8 : 1536 bytes 9 : 2048 bytes Fig. 3 Part Numbering 5 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GROUP EXPANSION Mitsubishi plans to expand the 38B5 group as follows: Memory Type Support for Mask ROM, One Time PROM and EPROM versions. Memory Size ROM/PROM size .................................................. 24K to 60K bytes RAM size ........................................................... 1024 to 2048 bytes Package 80P6N-A ..................................... 0.8 mm-pitch plastic molded QFP 80D0 ........................ 0.8 mm-pitch ceramic LCC (EPROM version) Under development ROM size (bytes) M38B59EF 60K 56K 52K New product M38B57MC 48K 44K 40K 36K 32K Planning 28K M38B57M6 24K 20K 16K 12K 8K 4K 256 512 768 1,024 1,536 2,048 RAM size (bytes) Note : Products under development or planning : the development schedule and specifications may be revised without notice. Fig. 4 Memory Expansion Plan Currently supported products are listed below. Table 3 List of Supported Products Product (P) ROM size (bytes) As of Jan. 1998 RAM size (bytes) Package 1024 80P6N-A Remarks ROM size for User ( ) M38B57MC-XXXFP 6 49152 (49022) Mask ROM version MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FUNCTIONAL DESCRIPTION Central Processing Unit (CPU) [CPU Mode Register] CPUM The 38B5 group uses the standard 740 family instruction set. Refer to the table of 740 family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction set. Machine-resident 740 Family instructions are as follows: •The FST and SLW instructions cannot be used. •The MUL, DIV, WIT and STP instructions can be used. b7 The CPU mode register contains the stack page selection bit and internal system clock control bits. The CPU mode register is allocated at address 003B16. b0 CPU mode register (CPUM (CM) : address 003B16) Processor mode bits b1 b0 0 0 : Single-chip mode 0 1 1 0 Not available 1 1 Stack page selection bit 0 : 0 page 1 : 1 page XCOUT drivability selection bit 0 : Low drive 1 : High drive Port XC switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function Main clock (XIN-XOUT) stop bit 0 : oscillating 1 : stopped Main clock division ratio selection bit 0 : f(XIN) (high-speed mode) 1 : f(XIN)/4 (middle-speed mode) Internal system clock selection bit 0 : XIN–XOUT selection (middle-/high-speed mode) 1 : XCIN–XCOUT selection (low-speed mode) Fig. 5 Structure of CPU Mode Register 7 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Memory Special function register (SFR) area Zero page RAM is used for data storage and for stack area of subroutine calls and interrupts. The 256 bytes from addresses 000016 to 00FF16 are called the zero page area. The internal RAM and the special function registers (SFR) are allocated to this area. The zero page addressing mode can be used to specify memory and register addresses in the zero page area. Access to this area with only 2 bytes is possible in the zero page addressing mode. ROM Special page The first 128 bytes and the last 2 bytes of ROM are reserved for device testing, and the other areas are user areas for storing programs. The 256 bytes from addresses FF0016 to FFFF16 are called the special page area. The special page addressing mode can be used to specify memory addresses in the special page area. Access to this area with only 2 bytes is possible in the special page addressing mode. The special function register (SFR) area in the zero page contains control registers such as I/O ports and timers. RAM Interrupt vector area The interrupt vector area contains reset and interrupt vectors. RAM area RAM size (byte) 192 256 384 512 640 768 896 1024 1536 2048 Address XXXX16 000016 SFR area 1 RAM 00FF16 013F16 01BF16 023F16 02BF16 033F16 03BF16 043F16 063F16 083F16 Zero page 004016 010016 XXXX16 Reserved area 044016 Not used (Note) 0EF016 0EFF16 0F0016 ROM area ROM size (byte) Address YYYY16 Address ZZZZ16 4096 8192 12288 16384 20480 24576 28672 32768 36864 40960 45056 49152 53248 57344 61440 F00016 E00016 D00016 C00016 B00016 A00016 900016 800016 700016 600016 500016 400016 300016 200016 100016 F08016 E08016 D08016 C08016 B08016 A08016 908016 808016 708016 608016 508016 408016 308016 208016 108016 ROM 0FFF16 YYYY16 SFR area 2 RAM area for Serial I/O automatic transfer RAM area for FLD automatic display Reserved ROM area (common ROM area,128 byte) ZZZZ16 FF0016 FFDC16 FFFE16 FFFF16 Special page Interrupt vector area Reserved ROM area Note: When 1024 bytes or more are used as RAM area, this area can be used. Fig. 6 Memory Map Diagram 8 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 000016 Port P0 (P0) 002016 Timer 1 (T1) 000116 Port P0 direction register (P0D) 002116 Timer 2 (T2) 000216 Port P1 (P1) 002216 Timer 3 (T3) 002316 Timer 4 (T4) 000316 000416 Port P2 (P2) 002416 Timer 5 (T5) 000516 Port P2 direction register (P2D) 002516 Timer 6 (T6) 000616 Port P3 (P3) 002616 PWM control register (PWMCON) 002716 Timer 6 PWM register (T6PWM) 000816 Port P4 (P4) 002816 Timer 12 mode register (T12M) 000916 Port P4 direction register (P4D) 002916 Timer 34 mode register (T34M) 000A16 Port P5 (P5) 002A16 Timer 56 mode register (T56M) 000B16 Port P5 direction register (P5D) 002B16 Watchdog timer control register (WDTCON) 000C16 Port P6 (P6) 002C16 Timer X (low-order) (TXL) 000D16 Port P6 direction register (P6D) 002D16 Timer X (high-order) (TXH) 000E16 Port P7 (P7) 002E16 Timer X mode register 1 (TXM1) 000F16 Port P7 direction register (P7D) 002F16 Timer X mode register 2 (TXM2) 001016 Port P8 (P8) 003016 Interrupt interval determination register (IID) 001116 Port P8 direction register (P8D) 003116 Interrupt interval determination control register (IIDCON) 001216 Port P9 (P9) 003216 A-D control register (ADCON) 001316 Port P9 direction register (P9D) 003316 A-D conversion register (low-order) (ADL) 001416 PWM register (high-order) (PWMH) 003416 A-D conversion register (high-order) (ADH) 001516 PWM register (low-order) (PWM L) 003516 001616 Baud rate generator (BRG) 003616 001716 UART control register (UARTCON) 003716 001816 Serial I/O1 automatic transfer data pointer (SIO1DP) 003816 001916 Serial I/O1 control register 1 (SIO1CON1) 003916 Interrupt source switch register (IFR) 001A16 Serial I/O1 control register 2 (SIO1CON2) 003A16 Interrupt edge selection register (INTEDGE) 001B16 Serial I/O1 register/Transfer counter (SIO1) 003B16 CPU mode register (CPUM) 001C16 Serial I/O1 control register 3 (SIO1CON3) 003C16 Interrupt request register 1(IREQ1) 001D16 Serial I/O2 control register (SIO2CON) 003D16 Interrupt request register 2(IREQ2) 001E16 Serial I/O2 status register (SIO2STS) 003E16 Interrupt control register 1(ICON1) 001F16 Serial I/O2 transmit/receive buffer register (TB/RB) 003F16 Interrupt control register 2(ICON2) 0EF016 Pull-up control register 1 (PULL1) 0EF816 FLD data pointer (FLDDP) 0EF116 Pull-up control register 2 (PULL2) 0EF916 Port P0FLD/port switch register (P0FPR) 0EF216 P1FLDRAM write disable register (P1FLDRAM) 0EFA16 Port P2FLD/port switch register (P2FPR) 0EF316 P3FLDRAM write disable register (P3FLDRAM) 0EFB16 Port P8FLD/port switch register (P8FPR) 0EF416 FLDC mode register (FLDM) 0EFC16 Port P8FLD output control register (P8FLDCON) 0EF516 Tdisp time set register (TDISP) 0EFD16 Buzzer output control register (BUZCON) 0EF616 Toff1 time set register (TOFF1) 0EFE16 0EF716 Toff2 time set register (TOFF2) 0EFF16 000716 Fig. 7 Memory Map of Special Function Register (SFR) 9 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER I/O Ports [Direction Registers] PiD The 38B5 group has 55 programmable I/O pins arranged in eight individual I/O ports (P0, P2, P40–P46, and P5–P9). The I/O ports have direction registers which determine the input/output direction of each individual pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input port or output port. When “0” is written to the bit corresponding to a pin, that pin becomes an input pin. When “1” is written to that pin, that pin becomes an output pin. If data is read from a pin set to output, the value of the port output latch is read, not the value of the pin itself. Pins set to input (the bit corresponding to that pin must be set to “0”) are floating and the value of that pin can be read. If a pin set to input is written to, only the port output latch is written to and the pin remains floating. b7 b0 P50, P51 pull-up control bit P52, P53 pull-up control bit P54, P55 pull-up control bit P56, P57 pull-up control bit P61 pull-up control bit [Pull-up Control Register] PULL Ports P5, P61–P65, P7, P84–P87 and P9 have built-in programmable pull-up resistors. The pull-up resistors are valid only in the case that the each control bit is set to “1” and the corresponding port direction registers are set to input mode. 10 0: No pull-up 1: Pull-up P62, P63 pull-up control bit P64, P65 pull-up control bit Not used (returns “0” when read) [High-Breakdown-Voltage Output Ports] The 38B5 group microprocessors have 5 ports with high-breakdownvoltage pins (ports P0–P3 and P80–P83). The high-breakdown-voltage ports have P-channel open-drain output with Vcc- 45 V of breakdown voltage. Each pin in ports P0, P1, and P3 has an internal pulldown resistor connected to VEE. At reset, the P-channel output transistor of each port latch is turned off, so that it goes to VEE level (“L”) by the pull-down resistor. Writing “1” (weak drivability) to bit 7 of the FLDC mode register (address 0EF416) shows the rising transition of the output transistors for reducing transient noise. At reset, bit 7 of the FLDC mode register is set to “0” (strong drivability). Pull-up control register 1 (PULL1 : address 0EF0 16) b7 b0 Pull-up control register 2 (PULL2 : address 0EF1 16) P70, P71 pull-up control bit P72, P73 pull-up control bit P74, P75 pull-up control bit P76, P77 pull-up control bit P84, P85 pull-up control bit 0: No pull-up 1: Pull-up P86, P87 pull-up control bit P90, P91 pull-up control bit Not used (returns “0” when read) Fig. 8 Structure of Pull-up Control Registers (PULL1 and PULL2) MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 4 List of I/O Port Functions (1) Pin P00/FLD8– P07/FLD15 Name Input/Output Port P0 Input/output, individual bits I/O Format Non-Port Function Related SFRs CMOS compatible input level FLD automatic display function FLDC mode register High-breakdown voltage PPort P0FLD/port switch register Ref.No. (1) channel open-drain output with pull-down resistor P10/FLD16– Port P1 Output P17/FLD23 P20/BUZ02/ High-breakdown voltage P- FLDC mode register (2) FLDC mode register (3) channel open-drain output Port P2 FLD0 Input/output, with pull-down resistor Low-voltage input level individual bits High-breakdown voltage P- Port P2FLD/port switch register channel open-drain output Buzzer output control register (1) High-breakdown voltage P- FLDC mode register (2) Interrupt edge selection register (4) P21/FLD1– Buzzer output (P20) P27/FLD7 P30/FLD24– Port P3 Output P37/FLD31 P40/INT0, channel open-drain output with pull-down resistor Port P4 P41/INT1, Input/output, CMOS compatible input level External interrupt input individual bits N-channel open-drain output P42/INT3 P43/BUZ01 P44/PWM1 Buzzer output PWM output Buzzer output control register Timer 56 mode register (5) (6) P45/T1OUT P46/T3OUT Timer output Timer output Timer 12 mode register Timer 34 mode register (7) (7) Interrupt edge selection register (8) P47/INT2 Input CMOS compatible input level External interrput input Interrupt interval determination control register P50/SIN1 P51/SOUT1, Port P5 Input/output, individual bits CMOS compatible input level Serial I/O1 function I/O CMOS 3-state output Serial I/O1 control register 1, 2 (9) (10) Serial I/O2 control register (9) UART control register (10) P52/SCLK11, P53/SCLK12 P54/RXD, Serial I/O2 function I/O P55/TXD, P56/SCLK21 ________ P57/SRDY2/ SCLK22 (11) P60/CNTR1 Port P6 CMOS compatible input level External count I/O N-channel open-drain output P61/CNTR0/ CNTR2 CMOS compatible input level CMOS 3-state output Interrupt edge selection register (4) (12) ________ P62/SRDY1/ AN8 Serial I/O1 function I/O A-D conversion input Serial I/O1 control register 1, 2 A-D control register P63/AN9 A-D conversion input A-D control register (14) P64/INT4/ S BUSY1/AN 10 Serial I/O1 function I/O A-D conversion input Serial I/O1 control register 1, 2 A-D control register (15) External interrupt input Interrupt edge selection register P65/SSTB1/ Serial I/O1 function I/O Serial I/O1 control register 1, 2 AN11 A-D conversion input A-D control register A-D conversion input A-D control register P70/AN0– P77/AN7 Port P7 (13) (16) (14) 11 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 5 List of I/O Port Functions (2) Name Input/Output I/O Format P80/FLD32– Port P8 P83/FLD35 Pin Input/output, individual bits Low-voltage input level High-breakdown voltage P- Non-Port Function Related SFRs FLD automatic display function FLDC mode register Port P8FLD/port switch register Ref.No. (1) channel open-drain output P84/FLD36 Low-voltage input level P85/RTP0/ CMOS 3-state output FLD37, (17) FLD automatic display function FLDC mode register Real time port output (18) Port P8FLD/port switch register P86/RTP1/ FLD38 P87/PWM0/ Timer X mode register 2 FLD automatic display function FLDC mode register FLD39 PWM output (19) Port P8FLD/port switch register PWM control register P90/XCIN P91/XCOUT Port P9 CMOS compatible input level Sub-clock generating circuit I/O CPU mode register (20) CMOS 3-state output (21) Notes 1 : How to use double-function ports as function I/O ports, refer to the applicable sections. 2 : Make sure that the input level at each pin is either 0 V or Vcc during execution of the STP instruction. When an input level is at an intermediate potential, a current will flow from Vcc to Vss through the input-stage gate. 12 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (2) Ports P1, P3 (1) Ports P0, P21–P27, P80–P83 FLD/Port switch register Dimmer signal (Note 1) * Port latch Data bus Dimmer signal (Note 1) Local data bus Direction register Local data bus * Port latch Data bus read VEE (Note 2) VEE (4) Ports P40–P42, P60 (3) Port P20 FLD/Port switch register Buzzer control signal Buzzer signal output Direction register Dimmer signal (Note 1) Local data bus Direction register Data bus Port latch Port latch Data bus * read INT0,INT1,INT3 interrupt input CNTR1 input Timer 4 external clock input (Note 2) VEE (6) Port P44 (5) Port P43 Buzzer control signal Buzzer signal output Timer 6 output selection bit Direction register Direction register Data bus Port latch Data bus Port latch Timer 6 output (7) Ports P45, P46 (8) Port P47 Timer 1 output bit Timer 3 output bit Direction register Data bus Data bus Port latch INT2 interrupt input Timer 1 output Timer 3 output * High-breakdown-voltage P-channel transistor Notes 1: The dimmer signal sets the Toff timing. 2: A pull-down resistor is not built in to ports P2 and P8. Fig. 9 Port Block Diagram (1) 13 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (9) Ports P50, P54 (10) Ports P51–P53, P55, P56 Pull-up control Pull-up control P-channel output disable signal (P51,P55) Output OFF control signal Serial I/O2 mode selection bit Direction register Direction register Port latch Data bus Port latch Data bus TXD, SOUT or SCLK Serial clock input Serial I/O input P52,P53,P56 (11) Port P57 (12) Port P61 Pull-up control Pull-up control Timer X operating mode bit SRDY2 output enable bit Direction register Direction register Data bus Data bus Port latch Timer X output CNTR0,CNTR2 input Timer2, TimerX external clock input Serial ready output Serial clock input (13) Port P62 Port latch (14) Ports P63, P7 Pull-up control P62/SRDY1•P64/SBUSY1 pin control bit Pull-up control Direction register Data bus Direction register Port latch Data bus Port latch Serial ready output Serial ready input A-D conversion input Analog input pin selection bit Fig. 10 Port Block Diagram (2) 14 A-D conversion input Analog input pin selection bit MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (15) Port P64 (16) Port P65 Pull-up control Pull-up control P62/SRDY1•P64/SBUSY1 pin control bit P65/SSTB1 pin control bit Direction register Direction register Data bus Port latch Data bus Port latch Analog input pin selection bit SBUSY1 output INT4 interrupt input, SBUSY1 input SSTB1 output A-D conversion input A-D conversion input (17) Port P84 (18) Ports P85, P86 Dimmer signal (Note) Dimmer signal (Note) Pull-up control FLD/Port switch register Real time port control bit Direction register Direction register Local data bus Port latch Data bus Local data bus Data bus Pull-up control FLD/Port switch register Port latch RTP output (19) Port P87 (20) Port P90 Dimmer signal (Note) FLD/Port switch register Pull-up control Port Xc switch bit P87/PWM output enable bit Pull-up control Direction register Local data bus Data bus Direction register Data bus Port latch PWM0 output Port latch Sub-clock generating circuit input (21) Port P91 Port Xc switch bit Pull-up control Direction register Data bus Port latch Oscillator Port P90 Port Xc switch bit * High-breakdown-voltage P-channel transistor Note: The dimmer signal sets the Toff timing. Fig. 11 Port Block Diagram (3) 15 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som Interrupts Interrupts occur by twenty one sources: five external, fifteen internal, and one software. (1) Interrupt Control Each interrupt except the BRK instruction interrupt have both an interrupt request bit and an interrupt enable bit, and is controlled by the interrupt disable flag. An interrupt occurs if the corresponding interrupt request and enable bits are “1” and the interrupt disable flag is “0.” Interrupt enable bits can be set or cleared by software. Interrupt request bits can be cleared by software, but cannot be set by software. The BRK instruction interrupt and reset cannot be disabled with any flag or bit. The I flag disables all interrupts except the BRK instruction interrupt and reset. If several interrupts requests occurs at the same time the interrupt with highest priority is accepted first. (2) Interrupt Operation Upon acceptance of an interrupt the following operations are automatically performed: 1. The contents of the program counter and processor status register are automatically pushed onto the stack. 2. The interrupt disable flag is set and the corresponding interrupt request bit is cleared. 3. The interrupt jump destination address is read from the vector table into the program counter. ■Notes on Use When the active edge of an external interrupt (INT0–INT4) is set or when switching interrupt sources in the same vector address, the corresponding interrupt request bit may also be set. Therefore, please take following sequence: (1) Disable the external interrupt which is selected. (2) Change the active edge in interrupt edge selection register (3) Clear the set interrupt request bit to “0.” (4) Enable the external interrupt which is selected. 16 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 6 Interrupt Vector Addresses and Priority Interrupt Source Priority Vector Addresses (Note 1) High Low Interrupt Request Remarks Generating Conditions Reset (Note 2) 1 FFFD16 FFFC16 At reset Non-maskable INT0 2 FFFB16 FFFA16 At detection of either rising or falling edge of External interrupt INT0 input (active edge selectable) INT1 3 FFF916 FFF816 At detection of either rising or falling edge of External interrupt INT2 4 FFF716 FFF616 INT1 input At detection of either rising or falling edge of (active edge selectable) External interrupt Remort control/ INT2 input (active edge selectable) At 8-bit counter overflow Valid when interrupt interval At completion of data transfer Valid when serial I/O1 ordinary At completion of the last data transfer mode is selected Valid when serial I/O1 automatic counter overflow Serial I/O1 determination is operating 5 FFF516 FFF416 Serial I/O1 automatic transfer transfer mode is selected Timer X 6 FFF316 FFF216 At timer X underflow Timer 1 7 FFF116 FFF016 At timer 1 underflow Timer 2 8 FFEF16 FFEE16 At timer 2 underflow Timer 3 Timer 4 9 10 FFED16 FFEB16 FFEC16 FFEA16 At timer 3 underflow At timer 4 underflow Timer 5 11 FFE916 FFE816 At timer 5 underflow STP release timer underflow Timer 6 12 FFE716 FFE616 At timer 6 underflow Serial I/O2 receive 13 FFE516 FFE416 At completion of serial I/O2 data receive INT3 14 FFE316 FFE216 At detection of either rising or falling edge of External interrupt INT3 input At completion of data transmit (active edge selectable) At detection of either rising or falling edge of External interrupt INT4 input (active edge selectable) Serial I/O2 transmit INT4 15 FFE116 FFE016 Valid when INT4 interrupt is selected A-D conversion FLD blanking FLD digit 16 FFDF16 FFDE16 At completion of A-D conversion Valid when A-D conversion is selected At falling edge of the last timing immediately before blanking period starts Valid when FLD blanking interrupt is selected At rising edge of each digit BRK instruction 17 FFDD16 FFDC16 At BRK instruction execution Notes 1 : Vector addresses contain interrupt jump destination addresses. 2 : Reset function in the same way as an interrupt with the highest priority. Valid when FLD digit interrupt is selected Non-maskable software interrupt 17 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Interrupt request bit Interrupt enable bit Interrupt disable flag I BRK instruction Reset Interrupt request Fig. 12 Interrupt Control b7 b0 Interrupt source switch register (IFR : address 003916) INT3/serial I/O2 transmit interrupt switch bit 0 : INT3 interrupt 1 : Serial I/O2 transmit interrupt INT4/AD conversion interrupt switch bit 0 : INT4 interrupt 1 : A-D conversion interrupt Not used (return “0” when read) (Do not write “1” to these bits.) b7 b0 Interrupt edge selection register (INTEDGE : address 003A16) INT0 interrupt edge selection bit INT1 interrupt edge selection bit INT2 interrupt edge selection bit INT3 interrupt edge selection bit INT4 interrupt edge selection bit Not used (return "0" when read) CNTR0 pin edge switch bit CNTR1 pin edge switch bit b7 0 : Falling edge active 1 : Rising edge active 0 : Rising edge count 1 : Falling edge count b0 Interrupt request register 1 (IREQ1 : address 003C16) b7 INT0 interrupt request bit INT1 interrupt request bit INT2 interrupt request bit Remote controller/counter overflow interrupt request bit Serial I/O1 interrupt request bit Timer 4 interrupt request bit Timer 5 interrupt request bit Timer 6 interrupt request bit Serial I/O2 receive interrupt request bit INT3/serial I/O2 transmit interrupt request bit INT4 interrupt request bit AD conversion interrupt request bit FLD blanking interrupt request bit FLD digit interrupt request bit Not used (returns “0” when read) Serial I/O automatic transfer interrupt request bit Timer X interrupt request bit Timer 1 interrupt request bit Timer 2 interrupt request bit Timer 3 interrupt request bit b7 b0 Interrupt control register 1 (ICON1 : address 003E16) INT0 interrupt enable bit INT1 interrupt enable bit INT2 interrupt enable bit Remote controller/counter overflow interrupt enable bit Serial I/O1 interrupt enable bit Serial I/O automatic transfer interrupt enable bit Timer X interrupt enable bit Timer 1 interrupt enable bit Timer 2 interrupt enable bit Timer 3 interrupt enable bit b0 Interrupt request register 2 (IREQ2 : address 003D16) 0 : No interrupt request issued 1 : Interrupt request issued b7 b0 Interrupt control register 2 (ICON2 : address 003F16) Timer 4 interrupt enable bit Timer 5 interrupt enable bit Timer 6 interrupt enable bit Serial I/O2 receive interrupt enable bit INT3/serial I/O2 transmit interrupt enable bit INT4 interrupt enable bit AD conversion interrupt enable bit FLD blanking interrupt enable bit FLD digit interrupt enable bit Not used (returns “0” when read) (Do not write “1” to this bit.) 0 : Interrupt disabled 1 : Interrupt enabled Fig. 13 Structure of Interrupt Related Registers 18 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Timers 8-Bit Timer The 38B5 group has six built-in timers : Timer 1, Timer 2, Timer 3, Timer 4, Timer 5, and Timer 6. Each timer has the 8-bit timer latch. All timers are down-counters. When the timer reaches “0016,” an underflow occurs with the next count pulse. Then the contents of the timer latch is reloaded into the timer and the timer continues down-counting. When a timer underflows, the interrupt request bit corresponding to that timer is set to “1.” The count can be stopped by setting the stop bit of each timer to “1.” The internal system clock can be set to either the high-speed mode or low-speed mode with the CPU mode register. At the same time, timer internal count source is switched to either f(XIN) or f(XCIN). ●Timer 1, Timer 2 The count sources of timer 1 and timer 2 can be selected by setting the timer 12 mode register. A rectangular waveform of timer 1 underflow signal divided by 2 is output from the P45/T1OUT pin. The waveform polarity changes each time timer 1 overflows. The active edge of the external clock CNTR0 can be switched with the bit 6 of the interrupt edge selection register. At reset or when executing the STP instruction, all bits of the timer 12 mode register are cleared to “0,” timer 1 is set to “FF16,” and timer 2 is set to “0116.” ●Timer 3, Timer 4 The count sources of timer 3 and timer 4 can be selected by setting the timer 34 mode register. A rectangular waveform of timer 3 underflow signal divided by 2 is output from the P46/T3OUT pin. The waveform polarity changes each time timer 3 overflows. The active edge of the external clock CNTR1 can be switched with the bit 7 of the interrupt edge selection register. ●Timer 5, Timer 6 The count sources of timer 5 and timer 6 can be selected by setting the timer 56 mode register. A rectangular waveform of timer 6 underflow signal divided by 2 is output from the P44/PWM1 pin. The waveform polarity changes each time timer 6 overflows. ●Timer 6 PWM1 Mode Timer 6 can output a rectangular waveform with “H” duty cycle n/ (n+m) from the P44/PWM1 pin by setting the timer 56 mode register (refer to Figure 16). The n is the value set in timer 6 latch (address 002516) and m is the value in the timer 6 PWM register (address 002716). If n is “0,” the PWM output is “L,” if m is “0,” the PWM output is “H” (n = 0 is prior than m = 0). In the PWM mode, interrupts occur at the rising edge of the PWM output. b7 b0 Timer 12 mode register (T12M: address 0028 16) Timer 1 count stop bit 0 : Count operation 1 : Count stop Timer 2 count stop bit 0 : Count operation 1 : Count stop Timer 1 count source selection bits 00 : f(XIN)/8 or f(XCIN)/16 01 : f(XCIN) 10 : f(XIN)/16 or f(X CIN)/32 11 : f(XIN)/64 or f(X CIN)/128 Timer 2 count source selection bits 00 : Underflow of Timer 1 01 : f(XCIN) 10 : External count input CNTR 0 11 : Not available Timer 1 output selection bit (P4 5) 0 : I/O port 1 : Timer 1 output Not used (returns “0” when read) (Do not write “1” to this bit.) b7 b0 Timer 34 mode register (T34M: address 0029 16) Timer 3 count stop bit 0 : Count operation 1 : Count stop Timer 4 count stop bit 0 : Count operation 1 : Count stop Timer 3 count source selection bits 00 : f(XIN)/8 or f(XCIN)/16 01 : Underflow of Timer 2 10 : f(XIN)/16 or f(XCIN)/32 11 : f(XIN)/64 or f(XCIN)/128 Timer 4 count source selection bits 00 : f(XIN)/8 or f(XCIN)/16 01 : Underflow of Timer 3 10 : External count input CNTR 1 11 : Not available Timer 3 output selection bit (P4 6) 0 : I/O port 1 : Timer 3 output Not used (returns “0” when read) (Do not write “1” to this bit.) b7 b0 Timer 56 mode register (T56M: address 002A 16) Timer 5 count stop bit 0 : Count operation 1 : Count stop Timer 6 count stop bit 0 : Count operation 1 : Count stop Timer 5 count source selection bit 0 : f(XIN)/8 or f(XCIN)/16 1 : Underflow of Timer 4 Timer 6 operation mode selection bit 0 : Timer mode 1 : PWM mode Timer 6 count source selection bits 00 : f(XIN)/8 or f(XCIN)/16 01 : Underflow of Timer 5 10 : Underflow of Timer 4 11 : Not available Timer 6 (PWM) output selection bit (P4 4) 0 : I/O port 1 : Timer 6 output Not used (returns “0” when read) (Do not write “1” to this bit.) Fig. 14 Structure of Timer Related Register 19 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Data bus XCIN Timer 1 count source “1” Internal system clock selection bit 1/8 XIN “0” RESET Timer 1 latch (8) 1/2 “01” selection bit Timer 1 (8) “00” 1/16 FF16 “10” STP instruction Timer 1 interrupt request Timer 1 count stop bit 1/64 P45/T1OUT “11” P45 latch 1/2 Timer 1 output selection bit Timer 2 latch (8) “00” Timer 2 count source selection bit 0116 Timer 2 (8) P45 direction register Timer 2 count stop bit “10” P61/CNTR0/CNTR2 Timer 2 interrupt request “01” Rising/Falling active edge switch Timer 3 latch (8) “01” “00” P46/T3OUT Timer 3 count source selection bit Timer 3 (8) Timer 3 interrupt request Timer 3 count stop bit “10” P46 latch “11” 1/2 Timer 3 output selection bit Timer 4 latch (8) “01” P46 direction register Timer 4 count source selection bit Timer 4 (8) “00” P60/CNTR1 Timer 4 interrupt request Timer 4 count stop bit “10” Rising/Falling active edge switch Timer 5 latch (8) “1” Timer 5 count source selection bit Timer 5 (8) “0” Timer 5 count stop bit “01” Timer 6 count source selection bit Timer 5 interrupt request Timer 6 latch (8) Timer 6 (8) “00” Timer 6 count stop bit “10” Timer 6 PWM register (8) P44/PWM1 P44 latch “1” “0” PWM 1/2 Timer 6 output selection bit Timer 6 operation mode selection bit P44 direction register Fig. 15 Block Diagram of Timer 20 Timer 6 interrupt request MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ts Timer 6 count source Timer 6 PWM mode n ✕ ts m ✕ ts (n+m) ✕ ts Timer 6 interrupt request Timer 6 interrupt request Note: PWM waveform (duty : n/(n + m) and period: (n + m) ✕ ts) is output. n : setting value of Timer 6 m: setting value of Timer 6 PWM register ts: period of Timer 6 count source Fig. 16 Timing Chart of Timer 6 PWM1 Mode 21 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 16-Bit Timer ■ Note Timer X is a 16-bit timer that can be selected in one of four modes by the Timer X mode register 1, 2 and can be controlled the timer X write and the real time port by setting the timer X mode registers. Read and write operation on 16-bit timer must be performed for both high- and low-order bytes. When reading a 16-bit timer, read from the high-order byte first. When writing to 16-bit timer, write to the loworder byte first. The 16-bit timer cannot perform the correct operation when reading during write operation, or when writing during read operation. •Timer X Write Control If the timer X write control bit is “0,” when the value is written in the address of timer X, the value is loaded in the timer X and the latch at the same time. If the timer X write control bit is “1,” when the value is written in the address of timer X, the value is loaded only in the latch. The value in the latch is loaded in timer X after timer X underflows. When the value is written in latch only, unexpected value may be set in the high-order counter if the writing in high-order latch and the underflow of timer X are performed at the same timing. ●Timer X Timer X is a down-counter. When the timer reaches “000016,” an underflow occurs with the next count pulse. Then the contents of the timer latch is reloaded into the timer and the timer continues downcounting. When a timer underflows, the interrupt request bit corresponding to that timer is set to “1.” (1) Timer mode A count source can be selected by setting the Timer X count source selection bits (bits 1 and 2) of the Timer X mode register 1. (2) Pulse output mode Each time the timer underflows, a signal output from the CNTR2 pin is inverted. Except for this, the operation in pulse output mode is the same as in timer mode. When using a timer in this mode, set the port shared with the CNTR2 pin to output. (3) Event counter mode The timer counts signals input through the CNTR2 pin. Except for this, the operation in event counter mode is the same as in timer mode. When using a timer in this mode, set the port shared with the CNTR2 pin to input. (4) Pulse width measurement mode A count source can be selected by setting the Timer X count source selection bits (bits 1 and 2) of the Timer X mode register 1. When CNTR2 active edge switch bit is “0,” the timer counts while the input signal of the CNTR2 pin is at “H.” When it is “1,” the timer counts while the input signal of the CNTR2 pin is at “L.” When using a timer in this mode, set the port shared with the CNTR2 pin to input. 22 •Real Time Port Control While the real time port function is valid, data for the real time port are output from ports P85 and P86 each time the timer X underflows. (However, if the real time port control bit is changed from “0” to “1,” data are output without the timer X.) When the data for the real time port is changed while the real time port function is valid, the changed data are output at the next underflow of timer X. Before using this function, set the corresponding port direction registers to output mode. MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group ge. ion. icat to chan ecif l sp ubject a in af es not mits ar li is is : Th metric e ic Not e para Som Real time port control bit “1” SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Data bus Q D P85 data for real time port P85 “0” Latch P85 direction register P85 latch Real time port control bit “1” Q D Real time port control bit (P85) “0” “0” Latch P86 direction register P86 latch Real time port control bit (P86) “0” “1” Timer X mode register write signal P86 data for real time port P86 XCIN 1/2 “1” Timer X mode register write signal Internal system clock selection bit 1/2 Count source selection bit 1/8 “0” 1/64 Timer X stop control bit Timer X operating Divider “1” XIN CNTR2 active edge switch bit P61/CNTR0/CNTR2 Timer X write control bit mode bit “0” Timer X latch (low-order) (8) Timer X latch (high-order) (8) “00”,“01”,“11” Timer X (low-order) (8) Timer X (high-order) (8) “10” “1” Pulse width measurement mode CNTR2 active edge switch bit “0” Pulse output mode Q P61 direction register “1” Timer X interrupt request S T Q P61 latch Pulse output mode CNTR0 Fig. 17 Block Diagram of Timer X b7 b7 b0 b0 Timer X mode register 1 (TXM1 : address 002E16) Timer X mode register 2 (TXM2 : address 002F16) Timer X write control bit 0 : Write data to both timer latch and timer 1 : Write data to timer latch only Timer X count source selection bits b2 b1 0 0 : f(XIN)/2 or f(XCIN)/4 0 1 : f(XIN)/8 or f(XCIN)/16 1 0 : f(XIN)/64 or f(XCIN)/128 1 1 : Not available Not used (returns "0" when read) Timer X operating mode bits b5 b4 0 0 : Timer mode 0 1 : Pulse output mode 1 0 : Event counter mode 1 1 : Pulse width measurement mode CNTR2 active edge switch bit 0 : • Event counter mode ; counts rising edges • Pulse output mode ; output starts with “H” level • Pulse width measurement mode ; measures “H” periods 1 : • Event counter mode ; counts falling edges • Pulse output mode ; output starts with “L” level • Pulse width measurement mode ; measures “L” periods Timer X stop control bit 0 : Count operating 1 : Count stop Real time port control bit (P85) 0 : Real time port function is invalid 1 : Real time port function is valid Real time port control bit (P86) 0 : Real time port function is invalid 1 : Real time port function is valid P85 data for real time port P86 data for real time port Not used (returns "0" when read) Fig. 18 Structure of Timer X Related Registers 23 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Serial I/O ●Serial I/O1 FLD automatic display RAM). ________ The P62/SRDY1/AN8, P64/INT4/SBUSY1/AN10, and P65/SSTB1/AN11 pins each have a handshake I/O signal function and can select either “H” active or “L” active for active logic. Serial I/O1 is used as the clock synchronous serial I/O and has an ordinary mode and an automatic transfer mode. In the automatic transfer mode, serial transfer is performed through the serial I/O automatic transfer RAM which has up to 256 bytes (addresses 0F0016 to 0FFF16: addresses 0F6016 to 0FFF16 are also used as Main address bus Local address bus Serial I/O automatic transfer RAM (0F0016—0FFF16) Main Local data bus data bus Serial I/O1 automatic transfer data pointer Address decoder Serial I/O1 automatic transfer controller XCIN 1/2 Serial I/O1 control register 3 Internal system clock selection bit “1” “0” P65 latch “0” P65/SSTB1 Divider XIN (P65/SSTB1 pin control bit) “1” P62/SRDY1•P64/SBUSY1 pin control bit P64 latch “0” Serial I/O1 synchronous clock selection bit “0” P64/SBUSY1 “1” P62/SRDY1•P64/SBUSY1 P62 latch pin control bit 1/4 1/8 1/16 1/32 1/64 1/128 1/256 Internal synchronous clock selection bits Synchronous circuit “1” SCLK1 “0” P62/SRDY1 “1” Serial I/O1 clock pin selection bit “0” “1” Serial transfer status flag P52 latch “0” P52/SCLK11 “0” “1” “1” Serial I/O1 counter “1” P53/SCLK12 Serial I/O1 clock pin selection bits “0” P53 latch “0” P51/SOUT1 P51 latch “1” Serial transfer selection bits P50/SIN1 Fig. 19 Block Diagram of Serial I/O1 24 Serial I/O1 register (8) Serial I/O1 interrupt request MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som b7 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b0 Serial I/O1 control register 1 (SIO1CON1 (SC11):address 0019 16) Serial transfer selection bits 00: Serial I/O disabled (pins P6 2,P64,P65,and P50—P53 are I/O ports) 01: 8-bits serial I/O 10: Not available 11: Automatic transfer serial I/O (8-bits) Serial I/O1 synchronous clock selection bits (P6 5/SSTB1 pin control bit) 00: Internal synchronous clock (P6 5 pin is an I/O port.) 01: External synchronous clock (P6 5 pin is an I/O port.) 10: Internal synchronous clock (P6 5 pin is an S STB1 output.) 11: Internal synchronous clock (P6 5 pin is an S STB1 output.) Serial I/O initialization bit 0: Serial I/O initialization 1: Serial I/O enabled Transfer mode selection bit 0: Full duplex (transmit and receive) mode (P5 0 pin is an SIN1 input.) 1: Transmit-only mode (P5 0 pin is an I/O port.) Transfer direction selection bit 0: LSB first 1: MSB first Serial I/O1 clock pin selection bit 0:SCLK11 (P53/SCLK12 pin is an I/O port.) 1:SCLK12 (P52/SCLK11 pin is an I/O port.) b7 b0 Serial I/O1 control register 2 (SIO1CON2 (SC12): address 001A 16) P62/SRDY1 • P64/SBUSY1 pin control bits 0000: Pins P62 and P64 are I/O ports 0001: Not used 0010: P62 pin is an S RDY1output, P64 pin is an I/O port. 0011: P62 pin is an S RDY1output, P64 pin is an I/O port. 0100: P62 pin is an I/O port, P6 4 pin is an SBUSY1 input. 0101: P62 pin is an I/O port, P6 4 pin is an SBUSY1 input. 0110: P62 pin is an I/O port, P6 4 pin is an SBUSY1 output. 0111: P62 pin is an I/O port, P6 4 pin is an SBUSY1 output. 1000: P62 pin is an S RDY1 input, P6 4 pin is an S BUSY1 output. 1001: P62 pin is an S RDY1 input, P6 4 pin is an S BUSY1 output. 1010: P62 pin is an S RDY1 input, P6 4 pin is an S BUSY1 output. 1011: P62 pin is an S RDY1 input, P6 4 pin is an S BUSY1 output. 1100: P62 pin is an S RDY1 output, P64 pin is an S BUSY1 input. 1101: P62 pin is an S RDY1 output, P64 pin is an S BUSY1 input. 1110: P62 pin is an S RDY1 output, P64 pin is an S BUSY1 input. 1111: P62 pin is an S RDY1 output, P64 pin is an S BUSY1 input. SBUSY1 output • SSTB1 output function selection bit (Valid in automatic transfer mode) 0: Functions as each 1-byte signal 1: Functions as signal for all transfer data Serial transfer status flag 0: Serial transfer completion 1: Serial transferring SOUT1 pin control bit (at no-transfer serial data) 0: Output active 1: Output high-impedance P51/SOUT1 P-channel output disable bit 0: CMOS 3-state (P-channel output is valid.) 1: N-channel open-drain (P-channel output is invalid.) Fig. 20 Structure of Serial I/O1 Control Registers 1, 2 25 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (1) Serial I/O1 Operation Either the internal synchronous clock or external synchronous clock can be selected by the serial I/O1 synchronous clock selection bits (b2 and b3 of address 001916) of serial I/O1 control register 1 as synchronous clock for serial transfer. The internal synchronous clock has a built-in dedicated divider where 7 different clocks are selected by the internal synchronous clock selection bits (b5, b6 and b7 of address 001C16) of serial I/O1 control register 3. ________ The P62/SRDY1/AN8, P64/INT4/SBUSY1/AN10, and P65/SSTB1/AN11 pins each select either I/O port or handshake I/O signal by the serial I/O1 synchronous clock selection bits (b2 and b3 of address ________ 001916) of serial I/O1 control register 1 as well as the P62/SRDY1 • P64/SBUSY1 pin control bits (b0 to b3 of address 001A16) of serial I/O1 control register 2. For the SOUT1 being used as an output pin, either CMOS output or N-channel open-drain output is selected by the P51/SOUT1 P-channel output disable bit (b7 of address 001A16) of serial I/O1 control register 2. Either output active or high-impedance can be selected as a SOUT1 pin state at serial non-transfer by the SOUT1 pin control bit (b6 of address 001A16) of serial I/O1 control register 2. However, when the external synchronous clock is selected, perform the following setup to put the SOUT1 pin into a high-impedance state. b7 When the SCLK1 input is “H” after completion of transfer, set the SOUT1 pin control bit to “1.” When the SCLK1 input goes to “L” after the start of the next serial transfer, the SOUT1 pin control bit is automatically reset to “0” and put into an output active state. Regardless of whether the internal synchronous clock or external synchronous clock is selected, the full duplex mode and the transmit-only mode are available for serial transfer, one of which is selected by the transfer mode selection bit (b5 of address 001916) of serial I/O1 control register 1. Either LSB first or MSB first is selected for the I/O sequence of the serial transfer bit strings by the transfer direction selection bit (b6 of address 001916) of serial I/O1 control register 1. When using serial I/O1, first select either 8-bit serial I/O or automatic transfer serial I/O by the serial transfer selection bits (b0 and b1 of address 001916) of serial I/O1 control register 1, after completion of the above bit setup. Next, set the serial I/O initialization bit (b4 of address 001916) of serial I/O1 control register 1 to “1” (Serial I/O enable) . When stopping serial transfer while data is being transferred, regardless of whether the internal or external synchronous clock is selected, reset the serial I/O initialization bit (b4) to “0.” b0 Serial I/O1 control register 3 (SIO1CON3 (SC13): address 001C16) Automatic transfer interval set bits 00000:2cycles of transfer clocks 00001:3cycles of transfer clocks : 11110:32cycles of transfer clocks 11111:33cycles of transfer clocks Data is written to a latch and read from a decrement counter. Internal synchronous clock selection bits 000:f(XIN)/4 or f(XCIN)/8 001:f(XIN)/8 or f(XCIN)/16 010:f(XIN)/16 or f(XCIN)/32 011:f(XIN)/32 or f(XCIN)/64 100:f(XIN)/64 or f(XCIN)/128 101:f(XIN)/128 or f(XCIN)/256 110:f(XIN)/256 or f(XCIN)/512 Fig. 21 Structure of Serial I/O1 Control Register 3 26 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (2) 8-bit Serial I/O Mode Address 001B16 is assigned to the serial I/O1 register. When the internal synchronous clock is selected, a serial transfer of the 8-bit serial I/O is started by a write signal to the serial I/O1 register (address 001B16). The serial transfer status flag (b5 of address 001A16) of serial I/O1 control register 2 indicates the shift register status of serial I/O1, and is set to “1” by writing into the serial I/O1 register, which becomes a transfer start trigger and reset to “0” after completion of 8bit transfer. At the same time, a serial I/O1 interrupt request occurs. When the external synchronous clock is selected, the contents of the serial I/O1 register are continuously shifted while transfer clocks are input to SCLK1. Therefore, the clock needs to be controlled externally. (3) Automatic Transfer Serial I/O Mode The serial I/O1 automatic transfer controller controls the write and read operations of the serial I/O1 register, so the function of address 001B16 is used as a transfer counter (1-byte units). When performing serial transfer through the serial I/O automatic transfer RAM (addresses 0F0016 to 0FFF16), it is necessary to set the serial I/O1 automatic transfer data pointer (address 001816) beforehand. Input the low-order 8 bits of the first data store address to be serially transferred to the automatic transfer data pointer set bits. When the internal synchronous clock is selected, the transfer interval for each 1-byte data can be set by the automatic transfer interval set bits (b0 to b4 of address 001C16) of serial I/O1 control register 3 in the following cases: 1. When using no handshake signal 2. When using the SRDY1 output, SBUSY1 output, and SSTB1 output of the handshake signal independently 3. When using a combination of SRDY1 output and SSTB1 output or a combination of SBUSY1 output and SSTB1 output of the handshake signal It is possible to select one of 32 different values, namely 2 to 33 cycles of the transfer clock, as a setting value. When using the SBUSY1 output and selecting the SBUSY1 output • SSTB1 output function selection bit (b4 of address 001A16) of serial I/O1 control register 2 as the signal for all transfer data, provided b7 that the automatic transfer interval setting is valid, a transfer interval is placed before the start of transmission/reception of the first data and after the end of transmission/reception of the last data. For SSTB1 output, regardless of the contents of the SBUSY1 output • SSTB1 output function selection bit (b4), the transfer interval for each 1-byte data is longer than the set value by 2 cycles. Furthermore, when using a combination of SBUSY1 output and SSTB1 output as a signal for all transfer data, the transfer interval after the end of transmission/reception of the last data is longer than the set value by 2 cycles. When the external synchronous clock is selected, automatic transfer interval setting is disabled. After completion of the above bit setup, if the internal synchronous clock is selected, automatic serial transfer is started by writing the value of “number of transfer bytes - 1” into the transfer counter (address 001B16). When the external synchronous clock is selected, write the value of “number of transfer bytes - 1” into the transfer counter and input an internal system clock interval of 5 cycles or more. After that, input transfer clock to SCLK1. As a transfer interval for each 1-byte data transfer, input an internal system clock interval of 5 cycles or more from the clock rise time of the last bit. Regardless of whether the internal or external synchronous clock is selected, the automatic transfer data pointer and the transfer counter are decremented after each 1-byte data is received and then written into the automatic transfer RAM. The serial transfer status flag (b5 of address 001A16) is set to “1” by writing data into the transfer counter. Writing data becomes a transfer start trigger, and the serial transfer status flag is reset to “0” after the last data is written into the automatic transfer RAM. At the same time, a serial I/O1 interrupt request occurs. The values written in the automatic transfer data pointer set bits (b0 to b7 of address 001816) and the automatic transfer interval set bits (b0 to b4 of address 001C16) are held in the latch. When data is written into the transfer counter, the values latched in the automatic transfer data pointer set bits (b0 to b7) and the automatic transfer interval set bits (b0 to b4) are transferred to the decrement counter. b0 Serial I/O1 automatic transfer data pointer (SIO1DP: address 001816) Automatic transfer data pointer set bits Specify the low-order 8 bits of the first data store address on the serial I/O automatic transfer RAM. Data is written into the latch and read from the decrement counter. Fig. 22 Structure of Serial I/O1 Automatic Transfer Data Pointer 27 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Automatic transfer RAM FFF16 Automatic transfer data pointer 5216 F5216 F5116 F5016 F4F16 F4E16 Transfer counter 0416 F0016 SIN1 SOUT1 Serial I/O1 register Fig. 23 Automatic Transfer Serial I/O Operation 28 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som (4) Handshake Signal 1. SSTB1 output signal The SSTB1 output is a signal to inform an end of transmission/reception to the serial transfer destination . The SSTB1 output signal can be used only when the internal synchronous clock is selected. In the initial status, namely, in the status in which the serial I/O initialization bit (b4) is reset to “0,” the SSTB1 output goes to “L,” or ________ the SSTB1 output goes to “H.” At the end of transmit/receive operation, when the data of the serial I/O1 register is all output from SOUT1, pulses are output in the period of 1 cycle of the transfer clock so as to cause the SSTB1 output ________ to go “H” or the SSTB1 output to go “L.” After that, each pulse is returned to the initial status in which SSTB1 output goes to “L” or the ________ SSTB1 output goes to “H.” Furthermore, after 1 cycle, the serial transfer status flag (b5) is reset to “0.” In the automatic transfer serial I/O mode, whether the SSTB1 output is to be active at an end of each 1-byte data or after completion of transfer of all data can be selected by the SBUSY1 output • SSTB1 output function selection bit (b4 of address 001A16) of serial I/O1 control register 2. SSTB1 Serial transfer status flag SCLK1 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER SBUSY1 SCLK1 SOUT1 Fig. 25 SBUSY1 Input Operation (internal synchronous clock) When the external synchronous clock is selected, input an “H” level _________ signal into the SBUSY1 input and an “L” level signal into the SBUSY1 input in the initial status in which transfer is stopped. At this time, the transfer clocks to be input in SCLK1 become invalid. During serial transfer, the transfer clocks to be input in SCLK1 become valid, enabling a transmit/receive operation, while an “L” level signal is input into the SBUSY1 input and an “H” level signal is input __________ into the SBUSY1 input. __________ When changing the input values in the SBUSY1 input and the SBUSY1 input at these operations, change them when the SCLK1 input is in a high state. When the high impedance of the SOUT1 output is selected by the SOUT1 pin control bit (b6), the SOUT1 output becomes active, enabling serial transfer by inputting a transfer clock to SCLK1, while an “L” level signal is input into the SBUSY1 input and an “H” level signal __________ is input into the SBUSY1 input. SOUT1 Fig. 24 SSTB1 Output Operation 2. SBUSY1 input signal The SBUSY1 input is a signal which receives a request for a stop of transmission/reception from the serial transfer destination. When the internal synchronous clock is selected, input an “H” level __________ signal into the SBUSY1 input and an “L” level signal into the SBUSY1 input in the initial status in which transfer is stopped. When starting a transmit/receive operation, input an “L” level signal __________ into the SBUSY1 input and an “H” level signal into the SBUSY1 input in the period of 1.5 cycles or more of the transfer clock. Then, transfer clocks are output from the SCLK1 output. When an “H” level signal is input into the SBUSY1 input and an “L” __________ level signal into the SBUSY1 input after a transmit/receive operation is started, this transmit/receive operation are not stopped immediately and the transfer clocks from the SCLK1 output is not stopped until the specified number of bits are transmitted and received. The handshake unit of the 8-bit serial I/O is 8 bits and that of the automatic transfer serial I/O is 8 bits. SBUSY1 SCLK1 Invalid SOUT1 (Output high-impedance) Fig. 26 SBUSY1 Input Operation (external synchronous clock) 3. SBUSY1 output signal The SBUSY1 output is a signal which requests a stop of transmission/reception to the serial transfer destination. In the automatic transfer serial I/O mode, regardless of the internal or external synchronous clock, whether the SBUSY1 output is to be active at transfer of each 1-byte data or during transfer of all data can be selected by the SBUSY1 output • SSTB1 output function selection bit (b4). In the initial status, the status in which the serial I/O initialization bit _________ (b4) is reset to “0,” the SBUSY1 output goes to “H” and the SBUSY1 output goes to “L.” 29 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som When the internal synchronous clock is selected, in the 8-bit serial I/O mode and the automatic transfer serial I/O mode (SBUSY1 output function outputs in 1-byte units), the SBUSY1 output goes to “L” _________ and the SBUSY1 output goes to “H” before 0.5 cycle (transfer clock) of the timing at which the transfer clock from the SCLK1 output goes to “L” at a start of transmit/receive operation. In the automatic transfer serial I/O mode (the SBUSY1 output function outputs all transfer data), the SBUSY1 output goes to “L” and the _________ SBUSY1 output goes to “H” when the first transmit data is written into the serial I/O1 register (address 001B16). When the external synchronous clock is selected, the SBUSY1 out__________ put goes to “L” and the SBUSY1 output goes to “H” when transmit 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER data is written into the serial I/O1 register to start a transmit operation, regardless of the serial I/O transfer mode. At termination of transmit/receive operation, the SBUSY1 output re__________ turns to “H” and the SBUSY1 output returns to “L”, the initial status, when the serial transfer status flag is set to "0", regardless of whether the internal or external synchronous clock is selected. Furthermore, in the automatic transfer serial I/O mode (SBUSY1 output function outputs in 1-byte units), the SBUSY1 output goes to “H” __________ and the SBUSY1 output goes to “L” each time 1-byte of receive data is written into the automatic transfer RAM. SBUSY1 SBUSY1 Serial transfer status flag Serial transfer status flag SCLK1 SCLK1 Write to Serial I/O1 register SOUT1 Fig. 27 SBUSY1 Output Operation (internal synchronous clock, 8-bits serial I/O) Fig. 28 SBUSY1 Output Operation (external synchronous clock, 8-bits serial I/O) Automatic transfer interval SCLK1 Serial I/O1 register →Automatic transfer RAM Automatic transfer RAM →Serial I/O1 register SBUSY1 Serial transfer status flag SOUT1 Fig. 29 SBUSY1 Output Operation in Automatic Transfer Serial I/O Mode (internal synchronous clock, SBUSY1 output function outputs each 1-byte) 30 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som 4. SRDY1 output signal The SRDY1 output is a transmit/receive enable signal which informs the serial transfer destination that transmit/receive is ready. In the initial status, when the serial I/O initialization bit (b4) is reset to “0,” ________ the SRDY1 output goes to “L” and the SRDY1 output goes to “H”. After transmitted data is stored in the serial I/O1 register (address 001B16) and a transmit/receive operation becomes ready, the SRDY1 output ________ goes to “H” and the SRDY1 output goes to “L”. When a transmit/ receive operation is started and the transfer clock goes to “L”, the ________ SRDY1 output goes to “L” and the SRDY1 output goes to “H”. 5. SRDY1 input signal The SRDY1 input signal becomes valid only when the SRDY1 input and the SBUSY1 output are used. The SRDY1 input is a signal for receiving a transmit/receive ready completion signal from the serial transfer destination. When the internal synchronous clock is selected, input a low level _________ signal into the SRDY1 input and a high level signal into the SRDY1 input in the initial status in which the transfer is stopped. When an “H” level signal is input into the SRDY1 input and an “L” _________ level signal is input into the SRDY1 input for a period of 1.5 cycles or more of transfer clock, transfer clocks are output from the SCLK1 output and a transmit/receive operation is started. After the transmit/receive operation is started and an “L” level signal is input into the SRDY1 input and an “H” level signal into the _________ SRDY1 input, this operation cannot be immediately stopped. After the specified number of bits are transmitted and received, the transfer clocks from the SCLK1 output is stopped. The handshake unit of the 8-bit serial I/O and that of the automatic transfer serial I/O are of 8 bits. When the external synchronous clock is selected, the SRDY1 input becomes one of the triggers to output the SBUSY1 signal. _________ To start a transmit/receive operation (SBUSY1 output: “L,” SBUSY1 output: “H”), input an “H” level signal into the SRDY1 input and an “L” _________ level signal into the SRDY1 input, and also write transmit data into the serial I/O1 register. 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER SRDY1 SCLK1 Write to serial I/O1 register Fig. 30 SRDY1 Output Operation SRDY1 SCLK1 SOUT1 Fig. 31 SRDY1 Input Operation (internal synchronous clock) 31 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER A: SCLK1 SCLK1 SRDY1 SRDY1 SBUSY1 Write to serial I/O1 register SRDY1 SBUSY1 SBUSY1 A: Internal synchronous clock selection SCLK1 B: External synchronous clock selection B: Write to serial I/O1 register Fig. 32 Handshake Operation at Serial I/O1 Mutual Connecting (1) SCLK1 SCLK1 SRDY1 SRDY1 SBUSY1 A: Write to serial I/O1 register SRDY1 SBUSY1 SBUSY1 A: Internal synchronous clock selection SCLK1 B: External synchronous clock selection B: Fig. 33 Handshake Operation at Serial I/O1 Mutual Connecting (2) 32 Write to serial I/O1 register MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ●Serial I/O2 ister (address 001D16) to “1.” For clock synchronous serial I/O, the transmitter and the receiver must use the same clock for serial I/O2 operation. If an internal clock is used, transmit/receive is started by a write signal to the serial I/O2 transmit/receive buffer register (TB/ RB) (address 001F16). _________ When P57 (SCLK22) is selected as a clock I/O pin, SRDY2 output function is invalid, and P56 (SCLK21) is used as an I/O port. Serial I/O2 can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer (baud rate generator) is also provided for baud rate generation during serial I/O2 operation. (1) Clock Synchronous Serial I/O Mode The clock synchronous serial I/O mode can be selected by setting the serial I/O2 mode selection bit (b6) of the serial I/O2 control reg- Data bus Serial I/O2 control register Address 001F 16 Receive buffer register Shift clock “0” P56/SCLK21 P57/SRDY2/SCLK22 XIN Serial I/O2 clock I/O pin selection bit “0” Internal system clock selection bit Serial I/O2 synchronous clock selection bit “0” “1” 1/2 F/F P57/SRDY2/SCLK22 P55/TXD Clock control circuit “1” “1” XCIN Receive interrupt request (RI) Receive shift register P54/RXD Address 001D 16 Receive buffer full flag (RBF) BRG count source selection bit Division ratio 1/(n+1) Baud rate generator BRG clock Address 0016 16 1/4 switch bit Falling edge detector Serial I/O2 clock I/O pin selection bit 1/4 Clock control circuit Transmit shift register shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Shift clock Transmit shift register Transmit buffer register Transmit buffer empty flag (TBE) Serial I/O2 status register Address 001E 16 Address 001F 16 Data bus Fig. 34 Block Diagram of Clock Synchronous Serial I/O2 Transmit/Receive shift clock (1/2—1/2048 of internal clock or external clock) Serial I/O2 output TxD D0 D1 D2 D3 D4 D5 D6 D7 Serial I/O2 input RxD D0 D1 D2 D3 D4 D5 D6 D7 Receive enable signal SRDY2 Write-in signal to serial I/O2 transmit/receive buffer register (address 001F 16) TBE = 0 TBE = 1 TSC = 0 RBF = 1 TSC = 1 Overrun error (OE) detection Notes 1 : The transmit interrupt (TI) can be selected to occur either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting transmit interrupt source selection bit (TIC) of the serial I/O2 control register. 2 : If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TxD pin. 3 : The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1.” Fig. 35 Operation of Clock Synchronous Serial I/O2 Function 33 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (2) Asynchronous Serial I/O (UART) Mode The asynchronous serial I/O (UART) mode can be selected by clearing the serial I/O2 mode selection bit (b6) of the serial I/O2 control register (address 001D16) to “0.” Eight serial data transfer formats can be selected and the transfer formats used by the transmitter and receiver must be identical. The transmit and receive shift registers each have a buffer (the two buffers have the same address in memory). Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer, and receive data is read from the receive buffer. The transmit buffer can also hold the next data to be transmitted, and the receive buffer can receive 2-byte data continuously. Data bus Serial I/O2 control register Address 001D16 Address 001F 16 OE P54/RXD Receive buffer full flag (RBF) Receive interrupt request (RI) Receive buffer register Character length selection bit 7 bit ST detector Receive shift register 1/16 8 bit PE FE P56/SCLK21 P57/SRDY2/SCLK22 XIN “0” Clock control circuit Serial I/O2 synchronous clock selection bit Serial I/O2 clock I/O pin selection bit “1” Internal system clock selection bit “0” “1” XCIN UART control register Address 0017 16 SP detector 1/2 BRG count source selection bit Division ratio 1/(n+1) Baud rate generator Address 0016 16 “1” BRG clock switch bit 1/4 ST/SP/PA generator Transmit shift register shift completion flag (TSC) 1/16 Transmit shift register P55/TXD Transmit interrupt source selection bit Transmit interrupt request (TI) Character length selection bit Transmit buffer empty flag (TBE) Address 001E16 Transmit buffer register Address 001F16 Serial I/O2 status register Data bus Fig. 36 Block Diagram of UART Serial I/O2 Transmit or receive clock Write-in signal to transmit buffer register TBE=0 TSC=0 TBE=1 Serial I/O2 output TXD TBE=0 TBE=1 ST D0 D1 SP TSC=1* ST D0 D1 Read-out signal from receive buffer register SP * Generated at 2nd bit in 2-stop bit mode 1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit RBF=0 RBF=1 Serial I/O2 input RXD ST Fig. 37 Operation of UART Serial I/O2 Function 34 D0 D1 SP RBF=1 ST D0 D1 SP MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [Serial I/O2 Control Register] SIO2CON (001D16) Writing “0” to the serial I/O2 enable bit (SIOE : b7 of the serial I/O2 control register) also clears all the status flags, including the error flags. All bits of the serial I/O2 status register are initialized to “0” at reset, but if the transmit enable bit (b4) of the serial I/O2 control register has been set to “1,” the transmit shift register shift completion flag (b2) and the transmit buffer empty flag (b0) become “1.” The serial I/O2 control register contains eight control bits for serial I/O2 functions. [UART Control Register] UARTCON (001716) This is a 5 bit register containing four control bits (b0 to b3), which are valid when UART is selected and set the data format of data receive/transfer, and one control bit (b4), which is always valid and sets the output structure of the P55/TxD pin. [Serial I/O2 Transmit Buffer Register/Receive Buffer Register] TB/RB (001F16) [Serial I/O2 Status Register] SIO2STS (001E16) The transmit buffer and the receive buffer are located in the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is "0". The read-only serial I/O2 status register consists of seven flags (b0 to b6) which indicate the operating status of the serial I/O2 function and various errors. Three of the flags (b4 to b6) are only valid in the UART mode. The receive buffer full flag (b1) is cleared to “0” when the receive buffer is read. The error detection is performed at the same time data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A writing to the serial I/O2 status register clears error flags OE, PE, FE, and SE (b3 to b6, respectively). b7 b0 Serial I/O2 status register (SIO2STS : address 001E16) [Baud Rate Generator] BRG (001616) The baud rate generator determines the baud rate for serial transfer. With the 8-bit counter having a reload register, the baud rate generator divides the frequency of the count source by 1/(n+1), where n is the value written to the baud rate generator. b7 Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift register shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns "1" when read) b7 b0 UART control register (UARTCON : address 001716) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits b0 Serial I/O2 control register (SIO2CON : address 001D16) BRG count source selection bit (CSS) 0: f(XIN) or f(XCIN)/2 or f(XCIN) 1: f(XIN)/4 or f(XCIN)/8 or f(XCIN)/4 Serial I/O2 synchronous clock selection bit (SCS) 0: BRG/ 4 (when clock synchronous serial I/O is selected) BRG/16 (UART is selected) 1: External clock input (when clock synchronous serial I/O is selected) External clock input/16 (UART is selected) SRDY2 output enable bit (SRDY) 0: P57 pin operates as ordinary I/O pin 1: P57 pin operates as SRDY2 output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O2 mode selection bit (SIOM) 0: Asynchronous serial I/O (UART) 1: Clock synchronous serial I/O Serial I/O2 enable bit (SIOE) 0: Serial I/O2 disabled (pins P54 to P57 operate as ordinary I/O pins) 1: Serial I/O2 enabled (pins P54 to P57 operate as serial I/O pins) Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits P55/TXD P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open-drain output (in output mode) BRG clock switch bit 0: XIN or XCIN (depends on internal system clock) 1: XCIN Serial I/O2 clock I/O pin selection bit 0: SCLK21 (P57/SCLK22 pin is used as I/O port or SRDY2 output pin.) 1: SCLK22 (P56/SCLK21 pin is used as I/O port.) Not used (return "1" when read) Fig. 38 Structure of Serial I/O2 Related Register 35 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FLD Controller The 38B5 group has fluorescent display (FLD) drive and control circuits. The FLD controller consists of the following components: •40 pins for FLD control pins •FLDC mode register •FLD data pointer •FLD data pointer reload register •Tdisp time set register •Toff1 time set register •Toff2 time set register •Port P0FLD/port switch register •Port P2FLD/port switch register •Port P8FLD/port switch register •Port P8 FLD output control register •FLD automatic display RAM (max. 160 bytes) A gradation display mode can be used for bright/dark display as a display function. Main data bus Main address bus FLD automatic display RAM 0F6016 Local address bus 0FFF16 Local data bus FLD/P P20/FLD0 FLD/P P21/FLD1 FLD/P P22/FLD2 8 FLD/P P23/FLD3 FLD/P P24/FLD4 FLD/P P25/FLD5 FLD/P P26/FLD6 FLD/P P27/FLD7 000416 0EFA16 FLD/P FLD/P FLD/P FLD/P FLD/P FLD/P FLD/P FLD/P 0EF916 P00/FLD8 P01/FLD9 P02/FLD10 8 P03/FLD11 P04/FLD12 P05/FLD13 P06/FLD14 P07/FLD15 000016 P10/FLD16 P11/FLD17 P12/FLD18 8 P13/FLD19 P14/FLD20 P15/FLD21 P16/FLD22 P17/FLD23 000216 FLDC mode register (0EF416) FLD data pointer reload register (0EF816) Address decoder FLD data pointer (0EF816) Timing generator Fig. 39 Block Diagram for FLD Control Circuit 36 P30/FLD24 P31/FLD25 P32/FLD26 8 P33/FLD27 P34/FLD28 P35/FLD29 P36/FLD30 P37/FLD31 000616 FLD/P P80/FLD32 FLD/P P81/FLD33 FLD/P P82/FLD34 8 FLD/P P83/FLD35 FLD/P P84/FLD36 FLD/P P85/FLD37 FLD/P P86/FLD38 FLD/P P87/FLD39 001016 0EFB16 FLD blanking interrupt FLD digit interrupt MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [FLDC Mode Register] FLDM The FLDC mode register is a 8-bit register respectively which is used to control the FLD automatic display and to set the blanking time Tscan for key-scan. b7 b0 FLDC mode register (FLDM: address 0EF4 16) Automatic display control bit (P0, P1, P2, P3, P8) 0 : General-purpose mode 1 : Automatic display mode Display start bit 0 : Stop display 1 : Display (start to display by switching “0” to “1”) Tscan control bits 00 : FLD digit interrupt (at rising edge of each digit) 01 : 1 ✕ Tdisp FLD blanking interrupt 10 : 2 ✕ Tdisp (at falling edge of the last digit) 11 : 3 ✕ Tdisp Timing number control bit 0 : 16 timing mode 1 : 32 timing mode Gradation display mode selection control bit 0 : Not selecting 1 : Selecting (Note) Tdisp counter count source selection bit 0 : f(XIN)/16 or f(XCIN)/32 1 : f(XIN)/64 or f(XCIN)/128 High-breakdown voltage port drivability selection bit 0 : Drivability strong 1 : Drivability weak Note: When a gradation display mode is selected, a number of timing is max. 16 timing. (Set the timing number control bit to “0.”) Fig. 40 Structure of FLDC Mode Register 37 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FLD automatic display pins This setting is performed by writing a value into the FLD/port switch register (addresses 0EF916 to 0EFB16) of each port. This setting can be performed in units of bit. When “0” is set, the port is set to the general-purpose port. When “1” is set, the port is set to the FLD pin. There is no restriction on whether the FLD pin is to be used as a segment pin or a digit pin. When the automatic display control bits of the FLDC mode register (address 0EF416) are set to “1,” the ports of P0, P1, P2, P3 and P8 are used as FLD automatic display pins. When using the FLD automatic display mode, set each port to the FLD pin or the general-purpose port using the respective switch register in accordance with the number of segments and the number of digits. Table 7 Pins in FLD Automatic Display Mode Port Name Automatic Display Pins Setting Method P0, P2, P80–P83 FLD0–FLD15 FLD32–FLD35 The individual bits of the FLD/port switch register (addresses 0EF916–0EFB16) can be set each pin either FLD port (“1”) or general-purpose port (“0”). P1, P3 P84–P87 FLD16–FLD31 FLD36–FLD39 None (FLD only) The individual bits of the FLD/port switch register (address 0EFB16) can be set each pin to either FLD port (“1”) or general-purpose port (“0”). The output can be reversed by the port P8 FLD output control register (address 0EFC16). The port output format is the CMOS output format. When using the port as a display pin, a driver must be installed externally. Setting example 2 Setting example 1 15 8 Number of segments Number of digits Port P2 Port P0 0 0 0 0 0 0 0 0 P20 1 0 0 0 0 0 1 1 FLD8(SEG1) P01 Port P1 P24 P25 P26 P27 P02 P03 P04 P05 FLD14(SEG2) FLD15(SEG3) FLD17(DIG2) FLD18(DIG3) FLD19(DIG4) FLD20(SEG4) FLD21(SEG5) FLD22(SEG6) FLD23(SEG7) Port P3 FLD24(SEG8) FLD25(SEG9) FLD26(SEG10) FLD27(SEG11) FLD28(DIG5) FLD29(DIG6) FLD30(DIG7) FLD31(DIG8) Port P8 1 1 1 1 0 0 0 0 FLD32(SEG12) FLD33(SEG13) FLD34(SEG14) FLD35(SEG15) P84 P85 P86 P87 Fig. 41 Segment/Digit Setting Example 38 Setting example 4 18 20 16 10 25 15 P21 P22 P23 FLD16(DIG1) Setting example 3 1 1 1 1 1 1 1 1 FLD0(SEG1) 1 1 1 1 1 1 1 1 FLD8(SEG9) FLD9(SEG10) FLD10(SEG11) FLD11(SEG12) 1 1 1 1 0 0 0 0 FLD1(SEG2) FLD2(SEG3) FLD3(SEG4) FLD4(SEG5) FLD5(SEG6) FLD6(SEG7) FLD7(SEG8) FLD12(SEG13) FLD13(SEG14) FLD14(SEG15) FLD15(SEG16) FLD16(DIG1) FLD17(DIG2) FLD18(DIG3) FLD19(DIG4) FLD20(DIG5) FLD21(DIG6) FLD22(DIG7) FLD23(DIG8) 0 0 1 1 1 1 1 1 P20 P21 FLD2(SEG1) FLD3(SEG2) FLD4(SEG3) FLD5(SEG4) FLD6(SEG5) 1 1 1 1 1 1 1 1 FLD8(DIG1) FLD9(DIG2) FLD10(DIG3) FLD11(DIG4) 1 1 1 1 1 1 1 1 FLD32(SEG18) FLD33(SEG19) FLD34(SEG20) FLD35(SEG21) FLD36(SEG22) FLD37(SEG23) FLD38(SEG24) FLD39(SEG25) FLD13(DIG6) FLD14(DIG7) FLD15(DIG8) FLD6(SEG3) FLD7(SEG4) FLD8(SEG5) FLD9(SEG6) FLD10(SEG7) FLD11(SEG8) FLD12(SEG9) FLD13(SEG10) 1 1 1 1 1 1 1 1 FLD16(DIG1) FLD17(DIG2) FLD18(DIG3) FLD19(DIG4) FLD20(DIG5) FLD21(DIG6) FLD22(DIG7) FLD23(DIG8) FLD24(DIG17) FLD25(DIG18) FLD26(DIG19) FLD27(DIG20) 1 1 FLD25(DIG10) 1 FLD14(SEG11) 1 FLD28(SEG7) FLD29(SEG8) FLD30(SEG9) FLD31(SEG10) 0 FLD19(DIG12) FLD20(DIG13) FLD21(DIG14) FLD22(DIG15) FLD23(DIG16) 1 1 1 1 1 1 1 P20 P21 P22 P23 P24 P25 FLD4(SEG1) FLD5(SEG2) 1 1 1 1 1 1 1 1 FLD18(DIG11) 1 1 1 1 FLD28(DIG13) 1 FLD29(DIG14) 1 FLD30(DIG15) 1 FLD31(SEG17) 0 1 1 1 1 1 1 1 1 FLD12(DIG5) FLD17(DIG10) FLD24(DIG9) FLD25(DIG10) FLD26(DIG11) FLD27(DIG12) 0 0 0 0 1 1 1 1 0 0 1 1 FLD7(SEG6) FLD16(DIG9) 1 1 1 1 1 1 1 1 0 0 0 0 FLD32(SEG11) FLD33(SEG12) FLD34(SEG13) FLD35(SEG14) FLD36(SEG15) FLD37(SEG16) FLD38(SEG17) 1 FLD39(SEG18) FLD24(DIG9) 1 1 FLD15(SEG12) 1 FLD26(SEG13) 0 FLD27(SEG14) 0 FLD28(SEG15) 0 FLD29(SEG16) 0 1 0 0 0 0 0 0 0 0 0 0 0 P80 P81 P82 P83 P84 P85 P86 P87 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER FLD automatic display RAM [FLD Data Pointer and FLD Data Pointer Reload Register] The FLD automatic display RAM uses the 160 bytes of addresses 0F6016 to 0FFF16. For FLD, the 3 modes of 16-timing ordinary mode, 16-timing•gradation display mode and 32-timing mode are available depending on the number of timings and the presence/absence of gradation display. The automatic display RAM in each mode is as follows: (1) 16-timing•Ordinary Mode The 80 bytes of addresses 0FB016 to 0FFF16 are used as a FLD display data store area. Because addresses 0F6016 to 0FAF16 are not used as the automatic display RAM, they can be the ordinary RAM or serial I/O automatic reverse RAM. (2) 16-timing•Gradation Display Mode The 160 bytes of addresses 0F6016 to 0FFF16 are used. The 80 bytes of addresses 0FB016 to 0FFF16 are used as an FLD display data store area, while the 80 bytes of addresses 0F6016 to 0FAF16 are used as a gradation display control data store area. (3) 32-timing Mode The 160 bytes of addresses 0F6016 to 0FFF16 are used as an FLD display data store area. FLDDP (0EF816) 16-timing•ordinary mode Both the FLD data pointer and FLD data pointer reload register are 8-bit registers assigned at address 0EF816. When writing data to this address, the data is written to the FLD data pointer reload register; when reading data from this address, the value in the FLD data pointer is read. 16-timing•gradation display mode 0F6016 0F6016 0F6016 Gradation display control data stored area Not used 0FB016 1 to 32 timing display data stored area 0FB016 1 to 16 timing display data stored area 0FFF16 32-timing mode 1 to 16 timing display data stored area 0FFF16 0FFF16 Fig. 42 FLD Automatic Display RAM Assignment 39 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Data setup (1) 16-timing•Ordinary Mode The area of addresses 0FB0 16 to 0FFF 16 are used as a FLD automatic display RAM. When data is stored in the FLD automatic display RAM, the last data of FLD port P2 is stored at address 0FB0 16 , the last data of FLD port P0 is stored at address 0FC0 16 , the last data of FLD port P1 is stored at address 0FD0 16 , the last data of FLD port P3 is stored at address 0FE0 16 , and the last data of FLD port P8 is stored at address 0FF016, to assign in sequence from the last data respectively. The first data of the FLD port P2, P0, P1, P3, and P8 is stored at an address which adds the value of (the timing number – 1) to the corresponding address 0FB016, 0FC016, 0FD016, 0FE016, and 0FF016. Set the FLD data pointer reload register to the value given by the number of digits – 1. “1” is always written to bit 6, and “0” is always written to bit 5. Note that “0” is always read from bits 6 and 5 when reading. (2) 16-timing•Gradation Display Mode Display data setting is performed in the same way as that of the 16-timing•ordinary mode. Gradation display control data is arranged at an address resulting from subtracting 005016 from the display data store address of each timing and pin. Bright display is performed by setting “0,” and dark display is performed by setting “1.” (3) 32-timing Mode The area of addresses 0F60 16 to 0FFF 16 are used as a FLD automatic display RAM. When data is stored in the FLD automatic display RAM, the last data of FLD port P2 is stored at address 0F60 16 , the last data of FLD port P0 is stored at address 0F80 16 , the last data of FLD port P1 is stored at address 0FA0 16 , the last data of FLD port P3 is stored at address 0FC0 16 , and the last data of FLD port P8 is stored at address 0FE016, to assign in sequence from the last data respectively. The first data of the FLD port P2, P0, P1, P3, and P8 is stored at an address which adds the value of (the timing number – 1) to the corresponding address 0F6016, 0F8016, 0FA016, 0FC016, and 0FE016. Set the FLD data pointer reload register to the value given by the number of digits–1. “1” is always written to bit 6, and “0” is always written to bit 5. Note that “0” is always read from bits 6 and 5 when reading. Number of FLD segments: 15 Number of timing: 8 (FLD data pointer reload register = 7) Bit Address 0FB016 0FB116 0FB216 0FB316 0FB416 0FB516 0FB616 0FB716 0FB816 0FB916 0FBA16 0FBB16 0FBC16 0FBD16 0FBE16 0FBF16 0FC016 0FC116 0FC216 0FC316 0FC416 0FC516 0FC616 0FC716 0FC816 0FC916 0FCA16 0FCB16 0FCC16 0FCD16 0FCE16 0FCF16 0FD016 0FD116 0FD216 0FD316 0FD416 0FD516 0FD616 0FD716 0FD816 0FD916 0FDA16 0FDB16 0FDC16 0FDD16 0FDE16 0FDF16 0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916 0FFA16 0FFB16 0FFC16 0FFD16 0FFE16 0FFF16 Note: 7 6 5 4 3 2 1 0 The last timing (The last data of FLDP2) Timing for start (The first data of FLDP2) FLDP2 data area The last timing (The last data of FLDP0) Timing for start (The first data of FLDP0) FLDP0 data area The last timing (The last data of FLDP1) Timing for start (The first data of FLDP1) FLDP1 data area The last timing (The last data of FLDP3) Timing for start (The first data of FLDP3) FLDP3 data area The last timing (The last data of FLDP8) Timing for start (The first data of FLDP8) FLDP8 data area shaded area is used for segment. shaded area is used for digit. Fig. 43 Example of Using the FLD Automatic Display RAM in 16-timing•Ordinary Mode 40 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Number of FLD segments: 25 Number of timing: 15 (FLD data pointer reload register = 14) Bit Address 0FB016 0FB116 0FB216 0FB316 0FB416 0FB516 0FB616 0FB716 0FB816 0FB916 0FBA16 0FBB16 0FBC16 0FBD16 0FBE16 0FBF16 0FC016 0FC116 0FC216 0FC316 0FC416 0FC516 0FC616 0FC716 0FC816 0FC916 0FCA16 0FCB16 0FCC16 0FCD16 0FCE16 0FCF16 0FD016 0FD116 0FD216 0FD316 0FD416 0FD516 0FD616 0FD716 0FD816 0FD916 0FDA16 0FDB16 0FDC16 0FDD16 0FDE16 0FDF16 0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916 0FFA16 0FFB16 0FFC16 0FFD16 0FFE16 0FFF16 Note: 7 6 5 4 3 2 1 Bit 0 Address The last timing (The last data of FLDP2) FLDP2 data area Timing for start (The first data of FLDP2) The last timing (The last data of FLDP0) FLDP0 data area Timing for start (The first data of FLDP0) The last timing (The last data of FLDP1) FLDP1 data area Timing for start (The first data of FLDP1) The last timing (The last data of FLDP3) FLDP3 data area Timing for start (The first data of FLDP3) The last timing (The last data of FLDP8) FLDP8 data area Timing for start (The first data of FLDP8) shaded area is used for segment. shaded area is used for digit. 0F6016 0F6116 0F6216 0F6316 0F6416 0F6516 0F6616 0F6716 0F6816 0F6916 0F6A16 0F6B16 0F6C16 0F6D16 0F6E16 0F6F16 0F7016 0F7116 0F7216 0F7316 0F7416 0F7516 0F7616 0F7716 0F7816 0F7916 0F7A16 0F7B16 0F7C16 0F7D16 0F7E16 0F7F16 0F8016 0F8116 0F8216 0F8316 0F8416 0F8516 0F8616 0F8716 0F8816 0F8916 0F8A16 0F8B16 0F8C16 0F8D16 0F8E16 0F8F16 0F9016 0F9116 0F9216 0F9316 0F9416 0F9516 0F9616 0F9716 0F9816 0F9916 0F9A16 0F9B16 0F9C16 0F9D16 0F9E16 0F9F16 0FA016 0FA116 0FA216 0FA316 0FA416 0FA516 0FA616 0FA716 0FA816 0FA916 0FAA16 0FAB16 0FAC16 0FAD16 0FAE16 0FAF16 Note: 7 6 5 4 3 2 1 0 The last timing (The last data of FLDP2) FLDP2 gradation display data area Timing for start (The first data of FLDP2) The last timing (The last data of FLDP0) FLDP0 gradation display data area Timing for start (The first data of FLDP0) The last timing (The last data of FLDP1) FLDP1 gradation display data area Timing for start (The first data of FLDP1) The last timing (The last data of FLDP3) FLDP3 gradation display data area Timing for start (The first data of FLDP3) The last timing (The last data of FLDP8) FLDP8 gradation display data area Timing for start (The first data of FLDP8) shaded area is used for gradation display data. Fig. 44 Example of Using the FLD Automatic Display RAM in 16-timing•Gradation Display Mode 41 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Number of FLD segments: 18 Number of timing: 20 (FLD data pointer reload register = 19) Bit Address 0FB016 0FB116 0FB216 0FB316 0FB416 0FB516 0FB616 0FB716 0FB816 0FB916 0FBA16 0FBB16 0FBC16 0FBD16 0FBE16 0FBF16 0FC016 0FC116 0FC216 0FC316 0FC416 0FC516 0FC616 0FC716 0FC816 0FC916 0FCA16 0FCB16 0FCC16 0FCD16 0FCE16 0FCF16 0FD016 0FD116 0FD216 0FD316 0FD416 0FD516 0FD616 0FD716 0FD816 0FD916 0FDA16 0FDB16 0FDC16 0FDD16 0FDE16 0FDF16 0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916 0FFA16 0FFB16 0FFC16 0FFD16 0FFE16 0FFF16 Note: 7 6 5 4 3 2 1 Bit 0 Address Timing for start (The first data of FLDP1) The last timing (The last data of FLDP3) FLDP3 data area Timing for start (The first data of FLDP3) The last timing (The last data of FLDP8) FLDP8 data area Timing for start (The first data of FLDP8) 7 0F6016 0F6116 0F6216 0F6316 0F6416 0F6516 0F6616 0F6716 0F6816 0F6916 0F6A16 0F6B16 0F6C16 0F6D16 0F6E16 0F6F16 0F7016 0F7116 0F7216 0F7316 0F7416 0F7516 0F7616 0F7716 0F7816 0F7916 0F7A16 0F7B16 0F7C16 0F7D16 0F7E16 0F7F16 0F8016 0F8116 0F8216 0F8316 0F8416 0F8516 0F8616 0F8716 0F8816 0F8916 0F8A16 0F8B16 0F8C16 0F8D16 0F8E16 0F8F16 0F9016 0F9116 0F9216 0F9316 0F9416 0F9516 0F9616 0F9716 0F9816 0F9916 0F9A16 0F9B16 0F9C16 0F9D16 0F9E16 0F9F16 0FA016 0FA116 0FA216 0FA316 0FA416 0FA516 0FA616 0FA716 0FA816 0FA916 0FAA16 0FAB16 0FAC16 0FAD16 0FAE16 0FAF16 shaded area is used for segment. shaded area is used for digit. Fig. 45 Example of Using the FLD Automatic Display RAM in 32-timing Mode 42 6 5 4 3 2 1 0 The last timing (The last data of FLDP2) FLDP2 data area Timing for start (The first data of FLDP2) The last timing (The last data of FLDP0) FLDP0 data area Timing for start (The first data of FLDP0) The last timing (The last data of FLDP1) FLDP1 data area MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Digit data protect function The FLD automatic display RAM is provided with a data protect function that disables the RAM area data to be rewritten as digit data. This function can disable data from being written in optional bits in the RAM area corresponding to P1 to P3. A programming load can be reduced by protecting an area that requires no change after data such as digit data is written. Write digit data beforehand; then set “1” in the corresponding bits. With this, the setting is completed. The data protect area becomes the maximum RAM area of P1 and P3. For example, when bit 0 of P1 is protected in the 16timing•ordinary mode, bits 0 of RAM addresses 0FD016 to 0FDF16 can be protected. Likewise, in the 16-timing•gradation display mode, bits 0 of addresses 0FD016 to 0FDF16 and 0F8016 to 0F8F16 can be protected. In the 32-timing mode, bits 0 of addresses 0FA016 to 0FBF16 can be protected. b7 b7 b0 P1FLDRAM write disable register (P1FLDRAM : address 0EF216) b0 P3FLDRAM write disable register (P3FLDRAM : address 0EF316) FLDRAM corresponding to P10 FLDRAM corresponding to P30 FLDRAM corresponding to P11 FLDRAM corresponding to P31 FLDRAM corresponding to P12 FLDRAM corresponding to P32 FLDRAM corresponding to P13 FLDRAM corresponding to P33 FLDRAM corresponding to P14 FLDRAM corresponding to P34 FLDRAM corresponding to P15 FLDRAM corresponding to P35 FLDRAM corresponding to P16 FLDRAM corresponding to P36 FLDRAM corresponding to P17 FLDRAM corresponding to P37 0: Operating normally 1: Write disabled 0: Operating normally 1: Write disabled Fig. 46 Structure of FLDRAM Write Disable Register 43 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Setting method when using the grid scan type FLD When using the grid scan type FLD, set “1” in the RAM area corresponding to the digit ports that output “1” at each timing. Set “0” in the RAM area corresponding to the other digit ports. Number of timing: 10 The first second third.......................9th 10th DIG10 (P31) DIG9 (P30) DIG8 (P17) DIG2 (P11) DIG1 (P10) Segment output Fig. 47 Example of Digit Timing Using Grid Scan Type Number of FLD segments: 16 Number of timing: 10 (FLD data pointer reload register = 9) Bit Address 0FB016 0FB116 0FB216 0FB316 0FB416 0FB516 0FB616 0FB716 0FB816 0FB916 0FBA16 0FBB16 0FBC16 0FBD16 0FBE16 0FBF16 0FC016 0FC116 0FC216 0FC316 0FC416 0FC516 0FC616 0FC716 0FC816 0FC916 0FCA16 0FCB16 0FCC16 0FCD16 0FCE16 0FCF16 0FD016 0FD116 0FD216 0FD316 0FD416 0FD516 0FD616 0FD716 0FD816 0FD916 0FDA16 0FDB16 0FDC16 0FDD16 0FDE16 0FDF16 0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 0FF716 0FF816 0FF916 0FFA16 0FFB16 0FFC16 0FFD16 0FFE16 0FFF16 Note: 7 6 5 4 3 2 1 0 The last timing (The last data of FLDP2) FLDP2 data area Timing for start (The first data of FLDP2) The last timing (The last data of FLDP0) FLDP0 data area Timing for start (The first data of FLDP0) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 The last timing (The last data of FLDP1) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 The last timing (The last data of FLDP3) FLDP1 data area Timing for start (The first data of FLDP1) FLDP3 data area Timing for start (The first data of FLDP3) The last timing (The last data of FLDP8) FLDP8 data area Timing for start (The first data of FLDP8) shaded area is used for segment. shaded area is used for digit. Fig. 48 Example of Using the FLD Automatic Display RAM Using Grid Scan Type 44 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Timing setting Key-scan Each timing is set by the FLDC mode register, Tdisp time set register, Toff1 time set register, and Toff2 time set register. •Tdisp time setting Set the Tdisp time by the Tdisp counter count source selection bit of the FLDC mode register and the Tdisp time set register. Supposing that the value of the Tdisp time set register is n, the Tdisp time is represented as Tdisp = (n+1) ✕ t (t: count source synchronization). When the Tdisp counter count source selection bit of the FLDC mode register is “0” and the value of the Tdisp time set register is 200 (C816), the Tdisp time is: Tdisp = (200+1) ✕ 4 (at XIN= 4 MHz) = 804 µs. When reading the Tdisp time set register, the value in the counter is read out. •Toff1 time setting Set the Toff1 time by the Toff1 time set register. Supposing that the value of the Toff1 time set register is n1, the Toff1 time is represented as Toff1 = n1 ✕ t. When the Tdisp counter count source selection bit of the FLDC mode register is “0” and the value of the Toff1 time set register is 30 (1E16), Toff1 = 30 ✕ 4 (at XIN = 4 MHz) = 120 µs. •Toff2 time setting Set the Toff2 time by the Toff2 time set register. Supposing that the value of the Toff2 time set register is n2, the Toff2 time is represented as Toff2 = n2 ✕ t. When the Tdisp counter count source selection bit of the FLDC mode register is “0” and the value of the Toff2 time set register is 180 (B416), Toff2 = 180 ✕ 4 (at XIN = 4 MHz) = 720 µs. This Toff2 time setting is valid only for FLD ports which are in the gradation display mode and whose gradation display control RAM value is “1.” When a key-scan is performed with the segment during key-scan blanking period Tscan, take the following sequence: 1. Write “0” to bit 0 of the FLDC mode register (address 0EF416). 2. Set the port corresponding to the segment for key-scan to the output port. 3. Perform the key-scan. 4. After the key-scan is performed, write “1” to bit 0 of FLDC mode register (address 0EF416). ■ Note When performing a key-scan according to the above steps 1 to 4, take the following points into consideration. 1. Do not set “0” in bit 1 of the FLDC mode register (address 0EF416). 2. Do not set “1” in the ports corresponding to digits. P84 to P87 FLD Output Reverse Function P84 to P87 are provided with a function to reverse the polarity of the FLD output. This function is useful in adjusting the polarity when using an externally installed driver. The output polarity can be reversed by setting bit 0 of the port P8 FLD output control register to “1.” FLD automatic display start To perform FLD automatic display, set the following registers. •Port P0FLD/port switch register •Port P2FLD/port switch register •Port P8FLD/port switch register •FLDC mode register •Tdisp time set register •Toff1 time set register •Toff2 time set register •FLD data pointer FLD automatic display mode is selected by writing “1” to the bit 0 of the FLDC mode register (address 0EF416), and the automatic display is started by writing “1” to bit 1. During FLD automatic display, bit 1 of the FLDC mode register (address 0EF416) always keeps “1,” and FLD automatic display can be interrupted by writing “0” to bit 1. 45 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Repeat synchronous Tdisp Tn Segment Digit output Tscan Tn-1 Tn-2 T4 T3 T2 T1 Segment setting by software FLD blanking interrupt request occurs at the falling edge of the last timing. FLD digit interrupt request occurs at the rising edge of digit (each timing). Segment Digit Toff1 Tdisp Segment Digit When a gradation display mode is selected Pin under the condition that bit 5 of the FLDC mode register is “1,” and the corresponding gradation display control data value is “1.” Toff1 Toff2 Tdisp n: Number of timing Fig. 49 FLDC Timing b7 b0 P8FLD output control register (P8FLDCON: address 0EFC 16) P84–P87 FLD output reverse bits 0: Output normally 1: Reverse output Not available (returns “0” when read) Fig. 50 Structure of P8FLD Output Control Register 46 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER A-D Converter The 38B5 group has a 10-bit A-D converter. The A-D converter performs successive approximation conversion. conversion interrupt request bit to “1.” Note that the comparator is constructed linked to a capacitor, so set f(XIN) to at least 250 kHz during A-D conversion. Use a CPU system clock dividing the main clock XIN as the internal system clock. [A-D Conversion Register] AD One of these registers is a high-order register, and the other is a loworder register. The high-order 8 bits of a conversion result is stored in the A-D conversion register (high-order) (address 003416), and the low-order 2 bits of the same result are stored in bit 7 and bit 6 of the A-D conversion register (low-order) (address 0033 16 ). During A-D conversion, do not read these registers. b7 b0 A-D control register (ADCON: address 0032 16) Analog input pin selection bits 0000: P70/AN0 0001: P71/AN1 0010: P72/AN2 0011: P73/AN3 0100: P74/AN4 0101: P75/AN5 0110: P76/AN6 0111: P77/AN7 1000: P62/SRDY1/AN8 1001: P63/AN9 1010: P64/INT4/SBUSY1/AN10 1011: P65/SSTB1/AN11 [A-D Control Register] ADCON This register controls A-D converter. Bits 3 to 0 are analog input pin selection bits. Bit 4 is an AD conversion completion bit and “0” during A-D conversion. This bit is set to “1” upon completion of A-D conversion. A-D conversion is started by setting “0” in this bit. AD conversion completion bit 0: Conversion in progress 1: Conversion completed [Comparison Voltage Generator] The comparison voltage generator divides the voltage between AVSS and VREF, and outputs the divided voltages. Not used (returns “0” when read) b7 [Channel Selector] b0 A-D conversion register (high-order) (ADH: address 0034 16) The channel selector selects one of the input ports P77/AN7–P70/ ________ AN0, and P65/SSTB1/AN11–P62/SRDY1/AN8 and inputs it to the comparator. When port P64 is selected as an analog input pin, an external interrupt function (INT4) is invalid. AD conversion result stored bits b7 b0 A-D conversion register (low-order) (ADL: address 0033 16) [Comparator and Control Circuit] The comparator and control circuit compares an analog input voltage with the comparison voltage and stores the result in the A-D conversion register. When an A-D conversion is completed, the control circuit sets the AD conversion completion bit and the AD Not used (returns “0” when read) AD conversion result stored bits Fig. 51 Structure of A-D Control Register Data bus b7 b0 A-D control register 4 A-D control circuit Channel selector P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 P62/SRDY1/AN8 P63/AN9 P64/INT4/SBUSY1/AN10 P65/SSTB1/AN11 Comparator A-D interrupt request A-D conversion register (H) A-D conversion register (L) (Address 003416) (Address 003316) Resistor ladder AVSS VREF Fig. 52 Block Diagram of A-D Converter 47 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Pulse Width Modulation (PWM) The 38B5 group has a PWM function with a 14-bit resolution. When the oscillation frequency XIN is 4 MHz, the minimum resolution bit width is 250 ns and the cycle period is 4096 µs. The PWM timing generator supplies a PWM control signal based on a signal that is the frequency of the XIN clock. The explanation in the rest of this data sheet assumes XIN = 4 MHz. Data bus It is set to “1” when write. bit7 PWM register (low-order) (address 001516) bit7 bit5 bit0 bit0 PWM register (high-order) (address 001416) PWM latch (14-bit) MSB LSB 14 P87 latch P87/PWM0 14-bit PWM circuit XCIN XIN (4MHz) When an internal 1/2 system clock selection bit is set (64 µs cycle) Timing “1” to “0” generating unit for PWM (4096 µs cycle) “0” Fig. 53 PWM Block Diagram 48 PWM P87/PWM output selection bit P87/PWM output selection bit P87 direction register MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 1. Data setup The PWM output pin also function as port P87. Set port P87 to be the PWM output pin by setting bit 0 of the PWM control register (address 002616) to “1.” The high-order 8 bits of output data are set in the high-order PWM register PWMH (address 001416) and the low-order 6 bits are set in the low-order PWM register PWML (address 001516). 3. Transfer from register to latch Data written to the PWML register is transferred to the PWM latch once in each PWM period (every 4096 µs), and data written to the PWMH register is transferred to the PWM latch once in each subperiod (every 64 µs). When the PWML register is read, the contents of the latch are read. However, bit 7 of the PWML register indicates whether the transfer to the PWM latch is completed; the transfer is completed when bit 7 is “0.” Table 8 Relationship between Low-order 6-bit Data and Setting Period of ADD Bit Low-order 6-bit data Sub-periods tm lengthened (m = 0 to 63) 2. PWM operation The timing of the 14-bit PWM function is shown in Figure 56. The 14-bit PWM data is divided into the low-order 6 bits and the high-order 8 bits in the PWM latch. The high-order 8 bits of data determine how long an “H” level signal is output during each sub-period. There are 64 sub-periods in each period, and each sub-period t is 256 ✕ τ (= 64 µs) long. The signal’s “H” has a length equal to N times τ, and its minimum resolution = 250 ns. The last bit of the sub-period becomes the ADD bit which is specified either “H” or “L,” by the contents of PWML. As shown in Table 8, the ADD bit is decided either “H” or “L.” That is, only in the sub-period tm shown in Table 8 in the PWM cycle period T = 64t, the “H” duration is lengthened during the minimum resolution width τ period in comparison with the other period. For example, if the high-order eight bits of the 14-bit data are “0316” and the low-order six bits are “0516,” the length of the “H” level output in sub-periods t8, t24, t32, t40 and t56 is 4 τ, and its length 3 τ in all other sub-periods. Time at the “H” level of each sub-period almost becomes equal because the time becomes length set in the high-order 8 bits or becomes the value plus τ, and this sub-period t (= 64 µs, approximate 15.6 kHz) becomes cycle period approximately. LSB 000000 None 000001 m = 32 000010 000100 m = 16, 48 001000 m = 4, 12, 20, 28, 36, 44, 52, 60 010000 m = 2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 50, 54, 58, 62 100000 m = 1, 3, 5, 7, .................................................., 57, 59, 61, 63 m = 8, 24, 40, 56 4096 µs 64 µs 64 µs m=0 15.75 µs m=7 15.75 µs 15.75 µs 64 µs m=8 16.0 µs 64 µs 64 µs m=9 15.75 µs m = 63 15.75 µs 15.75 µs Pulse width modulation register H: 00111111 Pulse width modulation register L: 000101 Sub-periods where “H” pulse width is 16.0 µs: m = 8, 24, 32, 40, 56 Sub-periods where “H” pulse width is 15.75 µs: m = all other values Fig. 54 PWM Timing 49 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group ge. ion. icat to chan ecif l sp ubject a in af es not mits ar li is is : Th metric e ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 PWM control register (PWMCON: address 0026 16) P87/PWM output selection bit 0: I/O port 1: PWM output Not used (return “0” when read) Fig. 55 Structure of PWM Control Register Data 6A16 stored at address 001416 PWM register (high-order) 5916 Data 7B16 stored at address 001416 6A16 7B16 Data 2416 stored at address 001516 PWM register (low-order) 1316 Bit 7 cleared after transfer A416 Data 3516 stored at address 001516 2416 3516 Transfer from register to latch PWM latch (14-bit) 165316 1A9316 Transfer from register to latch B516 1AA416 1AA416 1EE416 1EF516 When bit 7 of PWML is “0,” transfer from register to latch is disabled. T = 4096 µs (64 ✕ 64 µs) t = 64 µs 6A (Example 1) 6B 6A 6B 6A 6B 6A 6B 6A 6B 6B 5 2 5 6B 6A 6B 6A 6B 6A 6B 6A 6B 6A 6B 6A 6B 6A 6B 6A PWM output 1 Low-order 6-bits output H = 6A16 L = 2416 5 6A (Example 2) 5 5 5 6B16............36 times (107) 6A 6A 6A 6B 6A 5 5 6B 6A 6B 6A 6A 6A 5 5 5 5 5 5 106 ✕ 64 + 36 6A16............28 times (106) 6B 6A 6B 6A 6B 6A 6A 6A 6B 6A 6B 6A 6B 6A 6A PWM output Low-order 6 bits output H = 6A16 L = 1816 4 3 4 6B16............24 times 4 3 4 6A16............40 times 4 3 4 106 ✕ 64 + 24 t = 64 µs (256 ✕ 0.25 µs) Minimum bit width PWM output 6B τ = 0.25 µs 6A 69 68 67 ……… 02 01 FF FE FD FC ……… 97 96 6A 69 68 67 ……… 02 01 FF FE FD FC ……… 97 96 2 ADD 8-bit counter 02 01 The ADD portions with additional τ are determined either “H” or “L” by low-order 6-bit data. 00 ADD “H” period length specified by PWMH 256 Fig. 56 14-bit PWM Timing 50 95 τ (64 µs), fixed ……… 02 01 00 95 ............. MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Interrupt Interval Determination Function The 38B5 group has an interrupt interval determination circuit. This interrupt interval determination circuit has an 8-bit binary up counter. Using this counter, it determines a duration of time from the rising edge (falling edge) of an input signal pulse on the P47/INT2 pin to the rising edge (falling edge) of the signal pulse that is input next. How to determine the interrupt interval is described below. 1. Enable the INT2 interrupt by setting bit 2 of the interrupt control register 1 (address 003E16). Select the rising interval or falling interval by setting bit 2 of the interrupt edge selection register (address 003A16). 2. Set bit 0 of the interrupt interval determination control register (address 003116) to “1” (interrupt interval determination operating). 3. Select the sampling clock of 8-bit binary up counter by setting bit 1 of the interrupt interval determination control register. When writing “0,” f(XIN)/128 is selected (the sampling interval: 32 µs at f(XIN) = 4.19 MHz); when “1,” f(XIN)/256 is selected (the sampling interval: 64 µs at f(X IN) = 4.19 MHz). 4. When the signal of polarity which is set on the INT2 pin (rising or falling edge) is input, the 8-bit binary up counter starts counting up of the selected counter sampling clock. 5. When the signal of polarity above 4 is input again, the value of the 8-bit binary up counter is transferred to the interrupt interval determination register (address 003016), and the remote control interrupt request occurs. Immediately after that, the 8-bit binary up counter continues to count up again from “0016.” 6. When count value reaches “FF16,” the 8-bit binary up counter stops counting up. Then, simultaneously when the next counter sampling clock is input, the counter sets value “FF16” to the interrupt interval determination register to generate the counter overflow interrupt request. Counter sampling clock selection bit f(XIN)/128 f(XIN)/256 Noise filter INT2 interrupt input Noise filter The P47/INT2 pin builds in the noise filter. The noise filter operation is described below. 1. Select the sampling clock of the input signal with bits 2 and 3 of the interrupt interval determination control register. When not using the noise filter, set “00.” 2. The P47/INT2 input signal is sampled in synchronization with the selected clock. When sampling the same level signal in a series of three sampling, the signal is recognized as the interrupt signal, and the interrupt request occurs. When setting bit 4 of interrupt interval determination control register to “1,” the interrupt request can occur at both rising and falling edges. When using the noise filter, set the minimum pulse width of the INT2 input signal to 3 cycles or more of the sample clock. Note: In the low-speed mode (CM7 = 1), the interrupt interval determination function cannot operate. 8-bit binary up counter Counter overflow interrupt request or remote control interrupt request Interrupt interval determination register address 003016 One-sided/both-sided detection selection bit Noise filter sampling clock selection bit 1/128 1/32 1/64 Data bus Divider f(XIN) Fig. 57 Interrupt Interval Determination Circuit Block Diagram 51 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group ge. ion. icat to chan ecif l sp ubject a in af es not mits ar li is is : Th metric e ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 Interrupt interval determination control register (IIDCON: address 003116) Interrupt interval determination circuit operating selection bit 0 : Stopped 1 : Operating Counter sampling clock selection bit 0 : f(XIN)/128 1 : f(XIN)/256 Noise filter sampling clock selection bits (INT2) 00 : Filter stop 01 : f(XIN)/32 10 : f(XIN)/64 11 : f(XIN)/128 One-sided/both-sided edge detection selection bit 0 : One-sided edge detection 1 : Both-sided edge detection (can be used when using a noise filter) Not used (return “0” when read) Fig. 58 Structure of Interrupt Interval Determination Control Register (When IIDCON4 = “0”) Noise filter sampling clock INT2 pin Acceptance of interrupt Counter sampling clock N 8-bit binary up counter value 0 1 3 2 5 4 0 1 FF ~ 3 ~ 2 FF N FF 6 Remote control interrupt request Remote control interrupt request 1 0 6 N Interrupt interval determination register value FE 6 Counter overflow interrupt request Fig. 59 Interrupt Interval Determination Operation Example (at rising edge active) (When IIDCON4 = “1”) Noise filter sampling clock INT2 pin Acceptance of interrupt Counter sampling clock FE N 8-bit binary up counter value 0 1 N Interrupt interval determination register value 2 0 1 2 N Remote control interrupt request 2 0 1 3 2 Remote control interrupt request 3 2 0 2 3 Remote control Remote control interrupt request interrupt request Fig. 60 Interrupt Interval Determination Operation Example (at both-sided edge active) 52 1 FF 2 0 FF 2 FF Counter overflow interrupt request 1 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Watchdog Timer The watchdog timer gives a mean of returning to the reset status when a program cannot run on a normal loop (for example, because of a software runaway). The watchdog timer consists of an 8-bit watchdog timer L and a 12-bit watchdog timer H. ●Standard operation of watchdog timer When any data is not written into the watchdog timer control register (address 002B16) after resetting, the watchdog timer is in the stop state. The watchdog timer starts to count down by writing an optional value into the watchdog timer control register (address 002B16) and an internal reset occurs at an underflow of the watchdog timer H. Accordingly, programming is usually performed so that writing to the watchdog timer control register (address 002B16) may be started before an underflow. When the watchdog timer control register (address 002B16) is read, the values of the 6 high-order bits of the watchdog timer H, STP instruction disable bit, and watchdog timer H count source selection bit are read. (1) Initial value of watchdog timer At reset or writing to the watchdog timer control register (address 002B16), a watchdog timer H is set to “FFF16” and a watchdog timer L to “FF16.” (2) Watchdog timer H count source selection bit operation Bit 7 of the watchdog timer control register (address 002B16) permits selecting a watchdog timer H count source. When this bit is set to XCIN (3) Operation of STP instruction disable bit Bit 6 of the watchdog timer control register (address 002B16) permits disabling the STP instruction when the watchdog timer is in operation. When this bit is “0,” the STP instruction is enabled. When this bit is “1,” the STP instruction is disabled. Once the STP instruction is executed, an internal resetting occurs. When this bit is set to “1,” it cannot be rewritten to “0” by program. This bit is cleared to “0” after resetting. ■ Note When releasing the stop mode, the watchdog timer performs its count operation even in the stop release waiting time. Be careful not to cause the watchdog timer H to underflow in the stop release waiting time, for example, by writing data in the watchdog timer control register (address 002B16) before executing the STP instruction. “FF16” is set when watchdog timer control register is written to. 1/2 Data bus “0” “1” Internal system clock selection bit (Note) “0,” the underflow signal of watchdog timer L becomes the count source. The detection time is set then to f(X IN) = 2.1 s at 4 MHz frequency and f(XCIN) = 512 s at 32 kHz frequency. When this bit is set to “1,” the count source becomes the signal divided by 8 for f(XIN) (or divided by 16 for f(XCIN)). The detection time in this case is set to f(XIN) = 8.2 ms at 4 MHz frequency and f(XCIN) = 2 s at 32 KHz frequency. This bit is cleared to “0” after resetting. Watchdog timer L (8) 1/8 “1” “0” Watchdog timer H (12) “FFF16” is set when watchdog timer control register is written to. Watchdog timer H count source selection bit XIN STP instruction disable bit STP instruction Reset circuit RESET Internal reset Note: Either high-speed, middle-speed or low-speed mode is selected by bit 7 of CPU mode register. Fig. 61 Block Diagram of Watchdog Timer b7 b0 Watchdog timer control register (WDTCON : address 002B16) Watchdog timer H (for read-out of high-order 6 bit) STP instruction disable bit 0: STP instruction enabled 1: STP instruction disabled Watchdog timer H count source selection bit 0: Watchdog timer L underflow 1: f(XIN)/8 or f(XCIN)/16 Fig. 62 Structure of Watchdog Timer Control Register 53 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Buzzer Output Circuit The 38B5 group has a buzzer output circuit. One of 1 kHz, 2 kHz and 4 kHz (at XIN = 4.19 MHz) frequencies can be selected by the buzzer output control register (address 0EFD16). Either P43/BUZ01 or P20/ BUZ02/FLD0 can be selected as a buzzer output port by the output port selection bits (b2 and b3 of address 0EFD16). The buzzer output is controlled by the buzzer output ON/OFF bit (b4). Port latch f(XIN) Divider 1/1024 1/2048 1/4096 Buzzer output Buzzer output ON/OFF bit Output port control signal Port direction register Fig. 63 Block Diagram of Buzzer Output Circuit b7 b0 Buzzer output control register (BUZCON: address 0EFD16) Output frequency selection bits (X IN = 4.19 MHz) 00 : 1 kHz (f(XIN)/4096) 01 : 2 kHz (f(XIN)/2048) 10 : 4 kHz (f(XIN)/1024) 11 : Not available Output port selection bits 00 : P20 and P43 function as ordinary ports. 01 : P43/BUZ01 functions as a buzzer output. 10 : P20/BUZ02 /FLD0 functions as a buzzer output. 11 : Not available Buzzer output ON/OFF bit 0 : Buzzer output OFF (“0” output) 1 : Buzzer output ON Not used (return “0” when read) Fig. 64 Structure of Buzzer Output Control Register 54 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som Reset Circuit SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ______ Poweron To reset the microcomputer, RESET pin should be held at an “L” ______ level for 2 µs or more. Then the RESET pin is returned to an “H” level (the power source voltage should be between 2.7 V and 5.5 V, and the oscillation should be stable), reset is released. After the reset is completed, the program starts from the address contained in address FFFD16 (high-order byte) and address FFFC16 (low-order byte). Make sure that the reset input voltage is less than 0.5 V for VCC of 2.7 V (switching to the high-speed mode, a power source voltage must be between 4.0 V and 5.5 V). RESET Power source voltage 0V VCC Reset input voltage 0V (Note) 0.2VCC Note : Reset release voltage ; Vcc=2.7 V RESET VCC Power source voltage detection circuit Fig. 65 Reset Circuit Example XIN φ RESET Internal reset Address ? ? ? ? FFFC FFFD ADL Data ADH, ADL ADH SYNC XIN: about 4000 cycles Notes 1: The frequency relation of f(X IN) and f(φ) is f(XIN)=4 • f(φ). 2: The question marks (?) indicate an undefined state that depends on the previous state. Fig. 66 Reset Sequence 55 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Address Register contents Address Register contents (1) Port P0 000016 0016 (33) Timer 34 mode register 002916 0016 (2) Port P0 direction register 000116 0016 (34) Timer 56 mode register 002A16 0016 (3) Port P1 000216 0016 (35) Watchdog timer control register 002B16 3F16 (4) Port P2 000416 0016 (36) Timer X (low-order) 002C16 FF16 (5) Port P2 direction register 000516 0016 (37) Timer X (high-order) 002D16 FF16 (6) Port P3 000616 0016 (38) Timer X mode register 1 002E16 0016 (7) Port P4 000816 0016 (39) Timer X mode register 2 002F16 0016 (8) Port P4 direction register 000916 0016 003116 0016 (9) Port P5 000A16 0016 (40) Interrupt interval determination control register (41) A-D control register 003216 1016 (10) Port P5 direction register 000B16 0016 (42) Interrupt source switch register 003916 0016 (11) Port P6 000C16 0016 (43) Interrupt edge selection register 003A16 0016 (12) Port P6 direction register 000D16 0016 (44) CPU mode register 003B16 0 1 0 0 1 0 0 0 (13) Port P7 000E16 0016 (45) Interrupt request register 1 003C16 0016 (14) Port P7 direction register 000F16 0016 (46) Interrupt request register 2 003D16 0016 (15) Port P8 001016 0016 (47) Interrupt control register 1 003E16 0016 (16) Port P8 direction register 001116 0016 (48) Interrupt control register 2 003F16 0016 (17) Port P9 001216 0016 (49) Pull-up control register 1 0EF016 0016 (18) Port P9 direction register 001316 0016 (50) Pull-up control register 2 0EF116 0016 (19) UART control register 001716 8016 (51) P1FLDRAM write disable register 0EF216 0016 (20) Serial I/O1 control register 1 001916 0016 (52) P3FLDRAM write disable register 0EF316 0016 (21) Serial I/O1 control register 2 001A16 0016 (53) FLDC mode register 0EF416 0016 (22) Serial I/O1 control register 3 001C16 0016 (54) Tdisp time set register 0EF516 0016 (23) Serial I/O2 control register 001D16 0016 (55) Toff1 time set register 0EF616 FF16 (24) Serial I/O2 status register 001E16 8016 (56) Toff2 time set register 0EF716 FF16 (25) Timer 1 002016 FF16 (57) Port P0FLD/port switch register 0EF916 0016 (26) Timer 2 002116 0116 (58) Port P2FLD/port switch register 0EFA16 0016 (27) Timer 3 002216 FF16 (59) Port P8FLD/port switch register 0EFB16 0016 (28) Timer 4 002316 FF16 (60) Port P8FLD output control register 0EFC16 0016 (29) Timer 5 002416 FF16 (61) Buzzer output control register 0EFD16 0016 (30) Timer 6 002516 FF16 (62) Processor status register (31) PWM control register 002616 0016 (63) Program counter (32) Timer 12 mode register 002816 0016 (PS) ✕ ✕ ✕ ✕ ✕ 1 ✕ ✕ (PCH) FFFD16 contents (PCL) FFFC16 contents X: Not fixed Since the initial values for other than above mentioned registers and RAM contents are indefinite at reset, they must be set. Fig. 67 Internal Status at Reset 56 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Clock Generating Circuit ●Oscillation control The 38B5 group has two built-in oscillation circuits. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT (XCIN and XCOUT). Use the circuit constants in accordance with the resonator manufacturer's recommended values. No external resistor is needed between XIN and XOUT since a feedback resistor exists on-chip. However, an external feedback resistor is needed between XCIN and XCOUT. Immediately after power on, only the XIN oscillation circuit starts oscillating, and XCIN and XCOUT pins function as I/O ports. (1) Stop mode If the STP instruction is executed, the internal system clock stops at an “H” level, and XIN and XCIN oscillators stop. Timer 1 is set to “FF16” and timer 2 is set to “0116.” Either XIN divided by 8 or XCIN divided by 16 is input to timer 1 as count source, and the output of timer 1 is connected to timer 2. The bits of the timer 12 mode register are cleared to “0.” Set the interrupt enable bits of the timer 1 and timer 2 to disabled (“0”) before executing the STP instruction. Oscillator restarts when an external interrupt is received, but the internal system clock is not supplied to the CPU until timer 1 underflows. This allows time for the clock circuit oscillation to stabilize. ●Frequency control (1) Middle-speed mode The internal system clock is the frequency of XIN divided by 4. After reset, this mode is selected. (2) High-speed mode The internal system clock is the frequency of XIN. (3) Low-speed mode The internal system clock is the frequency of XCIN divided by 2. (2) Wait mode If the WIT instruction is executed, the internal system clock stops at an “H” level. The states of XIN and XCIN are the same as the state before executing the WIT instruction. The internal system clock restarts at reset or when an interrupt is received. Since the oscillator does not stop, normal operation can be started immediately after the clock is restarted. ■Note If you switch the mode between middle/high-speed and low-speed, stabilize both XIN and XCIN oscillations. The sufficient time is required for the sub clock to stabilize, especially immediately after power on and at returning from stop mode. When switching the mode between middle/high-speed and low-speed, set the frequency on condition that f(XIN) > 3f(XCIN). (4) Low power consumption mode The low power consumption operation can be realized by stopping the main clock XIN in low-speed mode. To stop the main clock, set bit 5 of the CPU mode register to “1.” When the main clock XIN is restarted (by setting the main clock stop bit to “0”), set enough time for oscillation to stabilize. By clearing furthermore the XCOUT drivability selection bit (b3) of CPU mode register to “0,” low power consumption operation of less than 200 µA (f(XCIN) = 32 kHz) can be realized by reducing the drivability between XCIN and XCOUT. At reset or during STP instruction execution this bit is set to “1” and a strong drivability that has an easy oscillation start is set. XCIN XCOUT Rf XIN XOUT Rd CCIN CCOUT CIN COUT Fig. 68 Ceramic Resonator Circuit XCIN XCOUT open XIN XOUT open External oscillation circuit External oscillation circuit or external pulse VCC VCC VSS VSS Fig. 69 External Clock Input Circuit 57 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER XCOUT XCIN “0” “1” Port XC switch bit (Note 3) 1/2 XOUT XIN Timer 2 count source selection bit (Note 2) Timer 1 count source selection bit (Note 2) Internal system clock selection bit (Notes 1, 3) “1” Low-speed mode Timer 1 “1” 1/4 1/2 “0” Timer 2 “0” “0” “1” High-speed or middle-speed mode Main clock division ratio selection bits (Note 3) Middle-speed mode “1” Timing φ (internal clock) “0” Main clock stop bit (Note 3) Q High-speed or low-speed mode S R S Q STP instruction WIT instruction R Q S R Reset Interrupt disable flag l Interrupt request Notes 1: When low-speed mode is selected, set the port Xc switch bit (b4) to “1.” 2: Refer to the structure of the timer 12 mode register. 3: Refer to the structure of the CPU mode register. Fig. 70 Clock Generating Circuit Block Diagram 58 STP instruction MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Reset CM4 “1” CM7=0(4 MHz selected) CM6=0(high-speed) CM5=0(XIN oscillating) CM4=0(32 kHz stopped) “0 4 “0” CM 6 0” ” M “ “1 C ” “1 Middle-speed mode (φ =1 MHz) “0” “1 ” ” CM 4 CM “1 6 ” “0 ” High-speed mode (φ =4 MHz) CM 6 “1” “0” CM7=0(4 MHz selected) CM6=0(high-speed) CM5=0(X IN oscillating) CM4=1(32 kHz oscillating) “1” “1” CM 7 CM 7 “0” “0” CM7=0(4 MHz selected) CM6=1(middle-speed) CM5=0(XIN oscillating) CM4=1(32 kHz oscillating) CM4 “0” CM7=0(4 MHz selected) CM6=1(middle-speed) CM5=0(X IN oscillating) CM4=0(32 kHz stopped) High-speed mode (φ =4 MHz) “0” CM 6 “1” “1” Middle-speed mode (φ =1 MHz) C M 5 CM 5 “0 ” “0 CM 1” 6 “1 ” ” “0 “ Low-power dissipation mode (φ =16 kHz) CM7=1(32 kHz selected) CM6=1(middle-speed) CM5=1(XIN stopped) CM4=1(32 kHz oscillating) CM7=1(32 kHz selected) CM6=0(high-speed) CM5=0(XIN oscillating) CM4=1(32 kHz oscillating) Low-power dissipation mode (φ =16 kHz) CM 6 “1” ” CM 5 CM “1 6 ” “0 ” “0” “0” ” “1 “0” CM 5 “1” CM7=1(32 kHz selected) CM6=1(middle-speed) CM5=0(X IN oscillating) CM4=1(32 kHz oscillating) “1” Low-speed mode (φ =16 kHz) CM 6 “1” Low-speed mode (φ =16 kHz) “0” CM7=1(32 kHz selected) CM6=0(high-speed) CM5=1(X IN stopped) CM4=1(32 kHz oscillating) b7 b4 CPU mode register (CPUM : address 003B 16) CM4 : Port Xc switch bit 0: I/O port function 1: X CIN-XCOUT oscillating function CM5 : Main clock (X IN- XOUT) stop bit 0: Oscillating 1: Stopped CM6: Main clock division ratio selection bit 0: f(X IN) (High-speed mode) 1: f(X IN)/4 (Middle-speed mode) CM7: Internal system clock selection bit 0: X IN–XOUT selected (Middle-/High-speed mode) 1: X CIN–XCOUT selected (Low-speed mode) Notes 1: Switch the mode by the allows shown between the mode blocks. (Do not switch between the mode directly without an allow.) 2: The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is ended. 3: Timer operates in the wait mode. 4: When the stop mode is ended, a delay of approximately 1 ms occurs by Timer 1 in middle-/high-speed mode. 5: When the stop mode is ended, a delay of approximately 0.25 s occurs by Timer 1 in low-speed mode. 6: The example assumes that 4 MHz is being applied to the X IN pin and 32 kHz to the X CIN pin. φ indicates the internal system clock. Fig. 71 State Transitions of System Clock 59 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som NOTES ON PROGRAMMING Processor Status Register 38B5 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER A-D Converter The contents of the processor status register (PS) after a reset are undefined, except for the interrupt disable flag (I) which is “1.” After a reset, initialize flags which affect program execution. In particular, it is essential to initialize the index X mode (T) and the decimal mode (D) flags because of their effect on calculations. The comparator uses internal capacitors whose charge will be lost if the clock frequency is too low. Therefore, make sure that f(XIN) is at least on 250 kHz during an A-D conversion. Do not execute the STP or WIT instruction during an A-D conversion. Interrupts Instruction Execution Time The contents of the interrupt request bits do not change immediately after they have been written. After writing to an interrupt request register, execute at least one instruction before performing a BBC or BBS instruction. The instruction execution time is obtained by multiplying the frequency of the internal system clock by the number of cycles needed to execute an instruction. The number of cycles required to execute an instruction is shown in the list of machine instructions. The frequency of the internal system clock is the same of the XIN frequency in high-speed mode. Decimal Calculations •To calculate in decimal notation, set the decimal mode flag (D) to “1,” then execute an ADC or SBC instruction. Only the ADC and SBC instructions yield proper decimal results. After executing an ADC or SBC instruction, execute at least one instruction before executing a SEC, CLC, or CLD instruction. •In decimal mode, the values of the negative (N), overflow (V), and zero (Z) flags are invalid. At STP Instruction Release At the STP instruction release, all bits of the timer 12 mode register are cleared. The XCOUT drivability selection bit (the CPU mode register) is set to “1” (high drive) in order to start oscillating. Timers NOTES ON USE If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1). Notes on Built-in EPROM Version Multiplication and Division Instructions •The index X mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instruction. •The execution of these instructions does not change the contents of the processor status register. Ports The contents of the port direction registers cannot be read. The following cannot be used: •The data transfer instruction (LDA, etc.) •The operation instruction when the index X mode flag (T) is “1” •The addressing mode which uses the value of a direction register as an index •The bit-test instruction (BBC or BBS, etc.) to a direction register •The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a direction register. Use instructions such as LDM and STA, etc., to set the port direction registers. Serial I/O •Using an external clock When using an external clock, input “H” to the external clock input pin and clear the serial I/O interrupt request bit before executing serial I/O transfer and serial I/O automatic transfer. •Using an internal clock When using an internal clock, set the synchronous clock to the internal clock, then clear the serial I/O interrupt request bit before executing a serial I/O transfer and serial I/O automatic transfer. 60 The P47 pin of the One Time PROM version or the EPROM version functions as the power source input pin of the internal EPROM. Therefore, this pin is set at low input impedance, thereby being affected easily by noise. To prevent a malfunction due to noise, insert a resistor (approx. 5 kΩ) in series with the P47 pin. MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER DATA REQUIRED FOR MASK ORDERS ROM PROGRAMMING METHOD The following are necessary when ordering a mask ROM production: (1) Mask ROM Order Confirmation Form (2) Mark Specification Form (3) Data to be written to ROM, in EPROM form (three identical copies) The built-in PROM of the blank One Time PROM version and the EPROM version can be read or programmed with a general purpose PROM programmer using a special programming adapter. Set the address of PROM programmer in the user ROM area. Table 9 Special Programming Adapter Package Name of Programming Adapter 80P6N-A PCA7438F-80A 80D0 PCA7438L-80A The PROM of the blank One Time PROM version is not tested or screened in the assembly process and following processes. To ensure proper operation after programming, the procedure shown in Figure 72 is recommended to verify programming. Programming with PROM programmer Screening (Note) (150°C for 40 hours) Verification with PROM programmer Functional check in target device Note: The screening temperature is far higher than the storage temperature. Never expose to 150 °C exceeding 100 hours. Fig. 72 Programming and Testing of One Time PROM Version 61 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Table 10 Absolute Maximum Ratings Parameter Symbol VCC Power source voltage VEE Pull-down power source voltage VI Input voltage P47, P50–P57, P61–P65, P70– P77, P84–P87, P90, P91 VI Input voltage P40–P46, P60 VI Input voltage P00–P07, P20–P27, P80–P83 VI Input voltage RESET, XIN VI Input voltage XCIN VO Output voltage P00–P07, P10–P17, P20–P27, P30–P37, P80–P83 VO Output voltage P50–P57, P61–P65, P70–P77, P84–P87, P90, P91, XOUT, XCOUT VO Output voltage P40–P46, P60 Pd Power dissipation Topr Tstg 62 Conditions All voltages are based on VSS. Output transistors are cut off. Ratings Unit –0.3 to 7.0 V VCC – 45 to VCC +0.3 V –0.3 to VCC +0.3 V –0.3 to 13 V VCC – 45 to VCC +0.3 V –0.3 to VCC +0.3 V –0.3 to VCC +0.3 V VCC – 45 to VCC +0.3 V –0.3 to VCC +0.3 V –0.3 to 13 V 600 mW Operating temperature –20 to 85 °C Storage temperature –40 to 125 °C Ta = 25°C MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group ge. ion. icat to chan ecif l sp ubject a in af es not mits ar li is is : Th metric e ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER RECOMMENDED OPERATING CONDITIONS Table 11 Recommended Operating Conditions (1) (VCC = 4.0 to 5.5V, Ta = –20 to 85°C, unless otherwise noted) Symbol Limits Parameter Unit Min. Typ. Max. in high-speed mode 4.0 5.0 5.5 V in middle-/low-speed mode 2.7 5.0 5.5 V VCC Power source voltage VSS Power source voltage VEE Pull-down power source voltage VREF Analog reference voltage (when A-D converter is used) AVSS Analog power source voltage 0 V VCC – 43 VCC V 2.0 VCC V V 0 VIA Analog input voltage AN0–AN11 0 VCC V VIH “H” input voltage P40–P47, P50–P57, P60–P65, P70–P77, P90, P91 0.75VCC VCC V VIH “H” input voltage P84–P87 0.4VCC VCC V VIH “H” input voltage P00–P07 0.8VCC VCC V VIH “H” input voltage P20–P27, P80–P83 0.52VCC VCC V VIH “H” input voltage RESET 0.8VCC VCC V VIH “H” input voltage XIN, XCIN 0.8VCC VCC V VIL “L” input voltage P40–P47, P50–P57, P60–P65, P70–P77, P90, P91 0 0.25VCC V VIL “L” input voltage P84–P87 0 0.16VCC V VIL “L” input voltage P00–P07, P20–P27, P80–P83 0 0.2VCC V VIL “L” input voltage 0 0.2VCC V VIL “L” input voltage 0 0.2VCC V I OH(peak) “H” total peak output current (Note 1) P00–P07, P10–P17, P20–P27, P30–P37, P80–P83 –240 mA I OH(peak) “H” total peak output current (Note 1) P50–P57, P61–P65, P70–P77, P90, P91 –60 mA I OL(peak) “L” total peak output current (Note 1) P50–P57, P60–P65, P70–P77, P90, P91 100 mA I OL(peak) “L” total peak output current (Note 1) P40–P46, P84–P87 60 mA I OH(avg) “H” total average output current (Note 1) P00–P07, P10–P17, P20–P27, P30–P37, P80–P87 –120 mA ____________ ____________ RESET XIN, XCIN I OH(avg) “H” total average output current (Note 1) P50–P57, P61–P65, P70–P77, P90, P91 –30 mA I OL(avg) “L” total average output current (Note 1) P50–P57, P60–P65, P70–P77, P90, P91 50 mA I OL(avg) “L” total average output current (Note 1) P40–P46, P84–P87 30 mA IOH(peak) “H” peak output current (Note 2) P00–P07, P10–P17, P20–P27, P30–P37, P80–P83 –40 mA IOH(peak) “H” peak output current (Note 2) P50–P57, P61–P65, P70–P77, P84–P87, P90, P91 –10 mA IOL(peak) “L” peak output current (Note 2) P50–P57, P61–P65, P70–P77, P84–P87, P90, P91 10 mA IOL(peak) “L” peak output current (Note 2) P40–P46, P60 30 mA IOH(avg) “H” average output current (Note 3) P00–P07, P10–P17, P20–P27, P30–P37, P80–P83 –18 mA IOH(avg) “H” average output current (Note 3) P50–P57, P60–P65, P70–P77, P84–P87, P90, P91 –5 mA IOL(avg) “L” average output current (Note 3) P50–P57, P61–P65, P70–P77, P84–P87, P90, P91 5 mA IOL(avg) “L” average output current (Note 3) P40–P46, P60 15 mA Notes 1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100 ms. The total peak current is the peak value of all the currents. 2: The peak output current is the peak current flowing in each port. 3: The average output current IOL (avg), IOH (avg) in an average value measured over 100 ms. 63 MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 12 Recommended Operating Conditions (2) (VCC = 4.0 to 5.5V, Ta = –20 to 85°C, unless otherwise noted) Symbol Limits Parameter Min. f(CNTR0) f(CNTR1) Clock input frequency for timers 2, 4, and X (duty cycle 50 %) f(XIN) Main clock input oscillation frequency (Note 1) f(XCIN) Sub-clock input oscillation frequency (Note 1, 2) Typ. 32.768 Max. Unit 250 kHz 4.2 MHz 50 kHz Notes 1: When the oscillation frequency has a duty cycle of 50%. 2: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency on condition that f(XCIN) < f(XIN)/3. ELECTRICAL CHARACTERISTICS Table 13 Electrical Characteristics (1) (VCC = 4.0 to 5.5V, Ta = –20 to 85°C, unless otherwise noted) Symbol Parameter Test conditions Limits Min. Typ. Max. Unit VOH “H” output voltage P00–P07, P10–P17, P20–P27, P30–P37, P80–P83 IOH = –18 mA VCC–2.0 V VOH “H” output voltage P50–P57, P60–P65, P70–P77, P84–P87, P90, P91 IOH = –10 mA VCC–2.0 V VOL “L” output voltage P50–P57, P61–P65, P84–P87, P90, P91 IOL = 10 mA VOL “L” output voltage P40–P46, P60 IOL = 15 mA 0.6 2.0 V 2.0 V VT+–VT– Hysteresis P40–P42, P44–P47, P5, P60, P61, P64 0.4 VT+–VT– Hysteresis RESET, XIN 0.5 VT+–VT– Hysteresis XCIN IIH “H” input current P47, P50–P57, P61–P65, P70–P77, P84–P87 VI = VCC 5.0 µA IIH “H” input current P40–P46, P60 VI = 12 V 10.0 µA V V V 0.5 IIH “H” input current P20–P27, P80–P83 (Note) VI = VCC 5.0 µA IIH “H” input current RESET, XCIN VI = VCC 5.0 µA IIH “H” input current XIN VI = VCC IIL “L” input current P40–P47, P60 VI = VSS –5.0 µA IIL “L” input current P50–P57, P61–P65, P70–P77, P84–P87, P90, P91 VI = VSS Pull-up “off” –5.0 µA IIL “L” input current P20–P27, P80–P83 (Note) VCC = 5 V, VI = VSS Pull-up “on” –30 –70 –140 µA VCC = 3 V, VI = VSS Pull-up “on” –6.0 –25 –45 µA VI = VSS –5.0 µA –5.0 µA IIL “L” input current RESET, XCIN VI = VSS IIL “L” input current XIN VI = VSS ILOAD Output load current P00–P07, P10–P17, P30–P37 VEE = VCC–43 V, VOL = VCC Output transistors “off” ILEAK Output leak current P00–P07, P10–P17, P20–P27, P30–P37, P80–P83 VEE = VCC–43 V, VOL = VCC –43 V Output transistors “off” IREADH “H” read current VRAM RAM hold voltage Note: Except when reading ports P2 or P8. 64 µA 4.0 VI = 5 V When clock is stopped µA –4.0 300 600 900 µA –10 µA µA 1 2 5.5 V MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 14 Electrical Characteristics (2) (VCC = 4.0 to 5.5V, Ta = –20 to 85°C, unless otherwise noted) Symbol Parameter Power source current ICC Limits Test conditions Min. High-speed mode f(XIN) = 4.2 MHz f(XCIN) = 32 kHz Output transistors “off” Typ. Max. 7.5 15 Unit mA High-speed mode f(XIN) = 4.2 MHz (in WIT state) f(XCIN) = 32 kHz Output transistors “off” 1 mA Middle-speed mode f(XIN) = 4.2 MHz f(XCIN) = stopped Output transistors “off” 3 mA Middle-speed mode f(XIN) = 4.2 MHz (in WIT state) f(XCIN) = stopped Output transistors “off” 1 mA Low-speed mode f(XIN) = stopped f(XCIN) = 32 kHz Low-power dissipation mode (CM3 = 0) Output transistors “off” 60 200 µA Low-speed mode f(XIN) = stopped f(XCIN) = 32 kHz (in WIT state) Low-power dissipation mode (CM3 = 0) Output transistors “off” 20 40 µA Increment when A-D conversion is executed 0.6 All oscillation stopped (in STP state) Output transistors “off” 0.1 Ta = 25°C Ta = 85°C mA 1 µA 10 µA A-D CONVERTER CHARACTERISTICS Table 15 A-D Converter Characteristics (VCC = 4.0 to 5.5V, VSS = 0V, Ta = –20 to 85°C, f(XIN) = 250 kHz to 4.2 MHz in high-speed mode, unless otherwise noted) Symbol Parameter — Resolution — Absolute accuracy (excluding quantization error) Test conditions Limits Min. VCC = VREF = 5.12 V Max. 10 Bits ±1 ±2.5 LSB 62 tc(φ) µA TCONV Conversion time 61 IVREF Reference input current 150 200 IIA Analog port input current 0.5 5.0 RLADDER Ladder resistor 35 VREF = 5.0 V 50 Unit Typ. µA kΩ 65 MITSUBISHI MICROCOMPUTERS ARY N I LIM E R P 38B5 Group e. n. atio chang cific o spe bject t l a fin su ot a its are is n m This etric li : e m ic Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TIMING REQUIREMENTS Table 16 Timing Requirements (VCC = 4.0 to 5.5V, VSS = 0V, Ta = –20 to 85°C, unless otherwise noted) Symbol Limits Parameter Min. Typ. Max. Unit ____________ tW(RESET) Reset input “L” pulse width 2.0 µs tC(XIN) Main clock input cycle time (XIN input) 238 ns tWH(XIN) Main clock input “H” pulse width 60 ns tWL(XIN) Main clock input “L” pulse width 60 ns tC(XCIN) Sub-clock input cycle time (XCIN input) 20 µs tWH(XCIN) Sub-clock input “H” pulse width 5.0 µs tWL(XCIN) Sub-clock input “L” pulse width 5.0 µs tC(CNTR) CNTR0, CNTR1 input cycle time 4.0 µs tWH(CNTR) CNTR0, CNTR1 input “H” pulse width 1.6 µs tWL(CNTR) CNTR0, CNTR1 input “L” pulse width 1.6 µs tWH(INT) INT0 to INT4 input “H” pulse width 80 ns tWL(INT) INT0 to INT4 input “L” pulse width 80 ns tC(SCLK) Serial I/O clock input cycle time 0.95 µs tWH(SCLK) Serial I/O clock input “H” pulse width 400 ns tWL(SCLK) Serial I/O clock input “L” pulse width 400 ns tsu(SCLK–SIN) Serial I/O input set up time 200 ns th(SCLK–SIN) Serial I/O input hold time 200 ns SWITCHING CHARACTERISTICS Table 17 Switching Characteristics (VCC = 4.0 to 5.5V, VSS = 0V, Ta = –20 to 85°C, unless otherwise noted) Symbol Parameter Test conditions Limits Min. Typ. Max. Unit tWH(SCLK) Serial I/O clock output “H” pulse width CL = 100 pF tC(SCLK)/2–160 tWL(SCLK) Serial I/O clock output “L” pulse width CL = 100 pF tC(SCLK)/2–160 ns td(SCLK–SOUT) Serial I/O output delay time tv(SCLK–SOUT) Serial I/O output valid time tr(SCLK) Serial I/O clock output rising time CL = 100 pF 40 ns tf(SCLK) Serial I/O clock output falling time CL = 100 pF 40 ns tr(Pch–strg) P-channel high-breakdown voltage output rising time (Note 1) CL = 100 pF VEE = VCC–43 V 55 ns tr(Pch–weak) P-channel high-breakdown voltage output rising time (Note 2) CL = 100 pF VEE = VCC–43 V 1.8 µs ns 0.2 tc 0 ns Notes 1: When bit 7 of the FLDC mode register (address 0EF416) is at “0”. 2: When bit 7 of the FLDC mode register (address 0EF416) is at “1”. Serial I/O clock output port P52/SCLK11, P53/SCLK12, P56/SCLK21, P57/SCLK22 CL P0,P1,P2, P3,P80–P83 High-breakdown P-channel opendrain output port CL (Note) VEE Note: Ports P2 and P8 need external resistors. Fig. 73 Circuit for Measuring Output Switching Characteristics 66 ns MITSUBISHI MICROCOMPUTERS ARY N I IM L E PR 38B5 Group . . tion hange c ifica pec ject to s l fina sub ot a its are is n his tric lim T : e m ice Not e para Som SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Timing Diagram tC(CNTR) tWL(CNTR) tWH(CNTR) CNTR0,CNTR1 0.8VCC 0.2VCC tWL(INT) tWH(INT) INT0–INT4 0.8VCC 0.2VCC tW(RESET) RESET 0.8VCC 0.2VCC tC(XIN) tWL(XIN) tWH(XIN) XIN 0.8VCC 0.2VCC tC(XCIN) tWL(XCIN) tWH(XCIN) XCIN 0.8VCC 0.2VCC tC(SCLK) tf(SCLK) SCLK tWL(SCLK) tr tWH(SCLK) 0.8VCC 0.2VCC tsu(SIN-SCLK) th(SCLK-SIN) 0.8VCC 0.2VCC SIN td(SCLK-SOUT) tv(SCLK-SOUT) SOUT Fig. 74 Timing Diagram 67 Keep safety first in your circuit designs! ¡ Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials ¡ These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. ¡ Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. ¡ All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. ¡ Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. ¡ The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. ¡ If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. ¡ Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein. © 1998 MITSUBISHI ELECTRIC CORP. \KI-9802 Printed in Japan (ROD) 2 New publication, effective Feb. 1998. Specifications subject to change without notice. REVISION DESCRIPTION LIST Rev. No. 1.0 38B5 GROUP DATA SHEET Revision Description First Edition Rev. date 980202 (1/1)