CY7C1360B CY7C1362B 9-Mbit (256K x 36/512K x 18) Pipelined SRAM Functional Description[1] Features • Supports bus operation up to 225 MHz • Available speed grades are 225, 200 and 166 MHz • Registered inputs and outputs for pipelined operation • 3.3V core power supply • 2.5V/3.3V I/O operation • Fast clock-to-output times — 2.8 ns (for 225-MHz device) — 3.0 ns (for 200-MHz device) — 3.5 ns (for 166-MHz device) The CY7C1360B/CY7C1362B SRAM integrates 262,144 x 36 and 524,288 x 18 SRAM cells with advanced synchronous peripheral circuitry and a two-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive-edge-triggered Clock Input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining Chip Enable (CE1), depth-expansion Chip Enables (CE2 and CE3[2]), Burst Control inputs (ADSC, ADSP, and ADV), Write Enables (BWX, and BWE), and Global Write (GW). Asynchronous inputs include the Output Enable (OE) and the ZZ pin. Addresses and chip enables are registered at rising edge of clock when either Address Strobe Processor (ADSP) or Address Strobe Controller (ADSC) are active. Subsequent burst addresses can be internally generated as controlled by the Advance pin (ADV). • Provide high-performance 3-1-1-1 access rate • User-selectable burst counter supporting Intel Pentium® interleaved or linear burst sequences • Separate processor and controller address strobes • Synchronous self-timed writes • Asynchronous output enable • Single Cycle Chip Deselect • Offered in JEDEC-standard 100-pin TQFP, 119-ball BGA and 165-Ball fBGA packages • TQFP Available with 3-Chip Enable and 2-Chip Enable • IEEE 1149.1 JTAG-Compatible Boundary Scan • “ZZ” Sleep Mode Option Address, data inputs, and write controls are registered on-chip to initiate a self-timed Write cycle.This part supports Byte Write operations (see Pin Descriptions and Truth Table for further details). Write cycles can be one to two or four bytes wide as controlled by the Byte Write control inputs. GW when active LOW causes all bytes to be written. The CY7C1360B/CY7C1362B operates from a +3.3V core power supply while all outputs may operate with either a +2.5 or +3.3V supply. All inputs and outputs are JEDEC-standard JESD8-5-compatible. Selection Guide 225 MHz 200 MHz 166 MHz Unit Maximum Access Time 2.8 3.0 3.5 ns Maximum Operating Current 250 220 180 mA Maximum CMOS Standby Current 30 30 30 mA Shaded areas contain advance information. Please contact your local Cypress sales representative for availability of these parts. Notes: 1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com. 2. CE3 is for A version of TQFP (3 Chip Enable option) and 165 fBGA package only. 119 BGA is offered only in 2 Chip Enable. Cypress Semiconductor Corporation Document #: 38-05291 Rev. *C • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised April 9, 2004 CY7C1360B CY7C1362B 1 Logic Block DiagrC1360B (256K x 36) A0, A1, A ADDRESS REGISTER 2 A[1:0] MODE ADV CLK Q1 BURST COUNTER CLR AND Q0 LOGIC ADSC ADSP BWD DQD ,DQPD BYTE WRITE REGISTER DQD ,DQPD BYTE WRITE DRIVER BWC DQC ,DQPC BYTE WRITE REGISTER DQC ,DQPC BYTE WRITE DRIVER DQB ,DQPB BYTE WRITE REGISTER DQB ,DQPB BYTE WRITE DRIVER BWB BWA BWE ZZ SENSE AMPS OUTPUT REGISTERS OUTPUT BUFFERS E DQs DQPA DQPB DQPC DQPD DQA ,DQPA BYTE WRITE DRIVER DQA ,DQPA BYTE WRITE REGISTER GW CE1 CE2 CE3 OE MEMORY ARRAY ENABLE REGISTER INPUT REGISTERS PIPELINED ENABLE SLEEP CONTROL 2 Logic Block Diagram – CY7C1362B (512K x 18) A0, A1, A ADDRESS REGISTER 2 A[1:0] MODE BURST Q1 COUNTER AND LOGIC CLR Q0 ADV CLK ADSC ADSP BWB DQB,DQPB WRITE DRIVER DQB,DQPB WRITE REGISTER MEMORY ARRAY BWA DQA,DQPA WRITE DRIVER DQA,DQPA WRITE REGISTER SENSE AMPS OUTPUT REGISTERS OUTPUT BUFFERS DQs DQPA DQPB E BWE GW CE1 CE2 CE3 ENABLE REGISTER PIPELINED ENABLE INPUT REGISTERS OE ZZ SLEEP CONTROL Document #: 38-05291 Rev. *C Page 2 of 34 CY7C1360B CY7C1362B Pin Configurations CY7C1360B (256K X 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DQPB DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA DQPA NC NC NC VDDQ VSSQ NC NC DQB DQB VSSQ VDDQ DQB DQB NC VDD NC VSS DQB DQB VDDQ VSSQ DQB DQB DQPB NC VSSQ VDDQ NC NC NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CY7C1362B (512K x 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A NC NC VDDQ VSSQ NC DQPA DQA DQA VSSQ VDDQ DQA DQA VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA NC NC VSSQ VDDQ NC NC NC MODE A A A A A1 A0 NC / 72M NC / 36M VSS VDD NC / 18M A A A A A A A A MODE A A A A A1 A0 NC / 72M NC / 36M VSS VDD NC / 18M A A A A A A A A 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DQPC DQC DQc VDDQ VSSQ DQC DQC DQC DQC VSSQ VDDQ DQC DQC NC VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD DQPD A A CE1 CE2 NC NC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 BWD BWC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100-pin TQFP Pinout (3 Chip Enables) (A version) NC NC NC VDDQ VSSQ NC NC DQB DQB VSSQ VDDQ DQB DQB NC VDD NC VSS DQB DQB VDDQ VSSQ DQB DQB DQPB NC VSSQ VDDQ NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CY7C1362B (512K x 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 NC NC VSS VDD NC NC A A A A A A A 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DQPB DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA DQPA MODE A A A A A1 A0 NC NC VSS VDD NC NC A A A A A A A CY7C1360B (256K X 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 DQPC DQC DQC VDDQ VSSQ DQC DQC DQC DQC VSSQ VDDQ DQC DQC NC VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD DQPD 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 NC NC BWB BWA A VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 BWD BWC BWB BWA A VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100-pin TQFP (2 Chip Enables) (AJ Version) Document #: 38-05291 Rev. *C A NC NC VDDQ VSSQ NC DQPA DQA DQA VSSQ VDDQ DQA DQA VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA NC NC VSSQ VDDQ NC NC NC Page 3 of 34 CY7C1360B CY7C1362B Pin Configurations (continued) 119-ball BGA (2 Chip Enables with JTAG) 1 CY7C1360B (256K x 36) 3 4 5 A A ADSP A VDDQ 2 A 6 A 7 VDDQ B C NC NC CE2 A A A ADSC VDD A A A A NC NC D E DQC DQC DQPC DQC VSS VSS NC CE1 VSS VSS DQPB DQB DQB DQB F VDDQ DQC VSS OE VSS DQB VDDQ G H J K DQC DQC VDDQ DQD DQC DQC VDD DQD BWC VSS NC VSS ADV BWB VSS NC VSS DQB DQB VDD DQA DQB DQB VDDQ DQA L DQD DQD NC DQA VDDQ DQD BWA VSS DQA M BWD VSS DQA VDDQ N DQD DQD VSS VSS DQA DQA GW VDD CLK BWE A1 P DQD DQPD VSS A0 VSS DQPA DQA R NC A MODE VDD NC A NC T U NC VDDQ NC TMS A TDI A TCK A TDO NC NC ZZ VDDQ 6 7 CY7C1362B (512K x 18) 1 2 3 4 5 A VDDQ A A ADSP A A VDDQ B NC CE2 A A A NC C NC A A ADSC VDD A A NC D DQB NC VSS NC VSS DQPA NC E NC DQB VSS CE1 VSS NC DQA F VDDQ NC VSS VSS DQA VDDQ G H J NC DQB VDDQ DQB NC VDD BWB VSS NC OE ADV GW VDD VSS VSS NC NC DQA VDD DQA NC VDDQ K NC DQB VSS CLK VSS NC DQA L M DQB VDDQ NC DQB VSS VSS NC DQA NC NC VDDQ N DQB NC VSS BWE A1 BWA VSS VSS DQA NC P NC DQPB VSS A0 VSS NC DQA R T U NC NC VDDQ A A TMS MODE A TDI VDD NC TCK NC A TDO A A NC NC ZZ VDDQ Document #: 38-05291 Rev. *C Page 4 of 34 CY7C1360B CY7C1362B Pin Configurations (continued) 165-ball fBGA (3 Chip Enable with JTAG) CY7C1360B (256K x 36) 1 A B C D E F G H J K L M N P NC / 288M R 2 A 3 4 5 6 7 8 9 10 11 CE1 BWC BWB CE3 BWE ADSC ADV A NC NC A CE2 BWD BWA CLK GW A NC / 144M NC DQC VDDQ VSS VSS VSS VSS VSS VSS VDDQ VDDQ VSS VDD OE VSS VDD ADSP DQPC DQC VDDQ NC DQB DQPB DQB DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB DQC DQC NC DQD DQC VDDQ VDD VSS VSS VSS VDD DQB DQB DQC VSS DQD VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ VDDQ NC VDDQ DQB NC DQA DQB ZZ DQA DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA DQD DQPD DQD NC VDDQ VDDQ VDD VSS VSS NC VSS NC / 18M VSS NC VDD VSS VDDQ VDDQ DQA NC DQA DQPA NC NC / 72M A A TDI A1 TDO A A A A MODE NC / 36M A A TMS TCK A A A A 7 8 9 10 11 A A0 CY7C1362B (512K x 18) 1 2 A B C D E F G H J K L M N P NC / 288M A 3 4 5 6 NC CE3 A CE1 CE2 BWB NC NC BWA NC NC NC DQB VDDQ VSS VDD VSS VDDQ R CLK BWE GW ADSC OE ADV ADSP A VSS VSS VSS VSS VSS VDD VDDQ VSS VDDQ NC NC A NC / 144M DQPA DQA NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA NC NC DQB DQB VSS NC VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ NC VDDQ NC NC DQA DQA ZZ NC DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC DQB DQPB NC NC VDDQ VDDQ VDD VSS VSS NC VSS NC / 18M VSS NC VDD VSS VDDQ VDDQ DQA NC NC NC NC NC / 72M A A TDI A1 TDO A A A A MODE NC / 36M A A TMS A0 TCK A A A A Document #: 38-05291 Rev. *C Page 5 of 34 CY7C1360B CY7C1362B CY7C1360B–Pin Definitions Name TQFP 3-Chip Enable TQFP 2-Chip Enable BGA fBGA I/O Description A0, A1, A 37,36,32, 33,34,35, 43,44,45, 46,47,48, 49,50,81, 82,99,100 InputAddress Inputs used to select one of the 256K P4,N4, R6,P6,A2, 37,36,32, A10,B2, Synchronous address locations. Sampled at the rising edge of A2,C2, 33,34,35, the CLK if ADSP or ADSC is active LOW, and CE1, R2,3A, B10,P3,P4, 44,45,46, B3,C3, P8,P9,P10, 47,48,49, CE2, and CE3[2]are sampled active. A1, A0 are fed 50,81,82, T3,T4,A5, P11,R3,R4, to the two-bit counter.. 92,99,100 B5,C5, R8,R9,R10, R11 T5,A6,B6, C6,R6 BWA,BWB 93,94,95, 96 93,94,95, 96 L5,G5, G3,L3 B5,A5,A4, B4 InputByte Write Select Inputs, active LOW. Qualified Synchronous with BWE to conduct Byte Writes to the SRAM. Sampled on the rising edge of CLK. GW 88 88 H4 B7 InputGlobal Write Enable Input, active LOW. When Synchronous asserted LOW on the rising edge of CLK, a global Write is conducted (ALL bytes are written, regardless of the values on BWX and BWE). BWE 87 87 M4 A7 InputByte Write Enable Input, active LOW. Sampled Synchronous on the rising edge of CLK. This signal must be asserted LOW to conduct a Byte Write. CLK 89 89 K4 B6 98 98 E4 A3 InputChip Enable 1 Input, active LOW. Sampled on the Synchronous rising edge of CLK. Used in conjunction with CE2 and CE3[2] to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE2 97 97 B2 B3 InputChip Enable 2 Input, active HIGH. Sampled on Synchronous the rising edge of CLK. Used in conjunction with CE1 and CE3[2] to select/deselect the device. CE3[2] 92 - - A6 InputChip Enable 3 Input, active LOW. Sampled on the Synchronous rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. Not available for AJ package version. Not connected for BGA. Where referenced, CE3[2] is assumed active throughout this document for BGA. OE 86 86 F4 B8 ADV 83 83 G4 A9 BWC,BWD CE1 Document #: 38-05291 Rev. *C InputClock InputAsynchronous Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. InputAdvance Input signal, sampled on the rising Synchronous edge of CLK, active LOW. When asserted, it automatically increments the address in a burst cycle. Page 6 of 34 CY7C1360B CY7C1362B CY7C1360B–Pin Definitions (continued) TQFP 3-Chip Enable TQFP 2-Chip Enable BGA fBGA 84 84 A4 B9 InputAddress Strobe from Processor, sampled on Synchronous the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A1, A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC 85 85 B4 A8 InputAddress Strobe from Controller, sampled on the Synchronous rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A1, A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ZZ 64 64 T7 H11 52,53,56, 57,58,59, 62,63,68, 69,72,73, 74,75,78, 79,2,3,6,7, 8,9,12,13,1 8,19,22, 23,24,25, 28,29,51, 80,1,30 52,53,56, 57,58,59, 62,63,68, 69,72,73, 74,75,78, 79,2,3,6,7, 8,9,12,13,1 8,19,22, 23,24,25, 28,29,51, 80,1,30 K6,L6, M6,N6, K7,L7, N7,P7, E6,F6, G6,H6, D7,E7, G7,H7, D1,E1, G1,H1, E2,F2, G2,H2, K1,L1, N1,P1, K2,L2, M2,N2, P6,D6, D2,P2 VDD 15,41,65, 91 15,41,65, 91 VSS 17,40,67, 90 17,40,67, 90 Name ADSP DQs, DQPs Document #: 38-05291 Rev. *C I/O InputAsynchronous Description ZZ “Sleep” Input, active HIGH. When asserted HIGH places the device in a non-time-critical “sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. I/OBidirectional Data I/O lines. As inputs, they feed M11,L11, K11,J11, Synchronous into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data J10,K10, contained in the memory location specified by the L10,M10, addresses presented during the previous clock rise D10,E10, F10,G10, of the read cycle. The direction of the pins is D11,E11, controlled by OE. When OE is asserted LOW, the F11,G11, pins behave as outputs. When HIGH, DQs and D1,E1,F1, DQPX are placed in a three-state condition. G1,D2,E2, F2,G2,J1, K1,L1,M1, J2,K2,L2, M2,N11, C11,C1,N1 J2,C4,J4, D4,D8,E4, Power Supply Power supply inputs to the core of the device. R4,J6 E8,F4,F8, G4,G8,H4, H8,J4,J8, K4,K8,L4, L8,M4,M8 D3,E3, F3,H3, K3,M3, N3,P3, D5,E5, F5,H5, K5,M5, N5,P5 C4,C5,C6, C7,C8,D5, D6,D7,E5, E6,E7,F5, F6,F7,G5, G6,G7,H2, H5,H6,H7,J 5,J6,J7, K5,K6,K7, L5,L6,L7, M5,M6,M7, N4,N8 Ground Ground for the core of the device. Page 7 of 34 CY7C1360B CY7C1362B CY7C1360B–Pin Definitions (continued) Name TQFP 3-Chip Enable TQFP 2-Chip Enable BGA fBGA I/O - - I/O Ground Ground for the I/O circuitry. I/O Power Supply Power supply for the I/O circuitry. VSSQ 5,10,21,26, 5,10,21,26, 55,60,71, 55,60,71, 76 76 VDDQ 4,11,20,27, 4,11,20,27, A1,F1,J1, C3,C9,D3, 54,61,70, 54,61,70, M1,U1, D9,E3,E9,F 77 77 A7,F7,J7, 3,F9,G3, M7,U7 G9,J3,J9, K3,K9,L3, L9,M3,M9, N3,N9 MODE 31 31 R3 R1 TDO - - U5 P7 JTAG serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG feature is output Synchronous not being utilized, this pin should be disconnected. This pin is not available on TQFP packages. TDI - - U3 P5 JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not being input Synchronous utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP packages. TMS - - U2 R5 JTAG serial Serial data-In to the JTAG circuit. Sampled on the input rising edge of TCK. If the JTAG feature is not being Synchronous utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP packages. TCK - - U4 R7 JTAG-Clock Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must be connected to VSS. This pin is not available on TQFP packages. NC 14,16,66, 42,39,38 B1,C1, 14,16,38, 39,42,43, R1,T1,T2, J3,D4, 66, L4,5J,5R, 6T,6U, B7,C7, R7 Document #: 38-05291 Rev. *C A11,B1,C2, C10,H1,H3, H9,H10, N2,N5,N7, N10,P1,A1, B11,P2,R2, N6 InputStatic Description - Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode pin has an internal pull-up. No Connects. Not internally connected to the die Page 8 of 34 CY7C1360B CY7C1362B CY7C1362B–Pin Definitions TQFP 3-Chip Enable TQFP 2-Chip Enable A0, A1, A 37,36,32, 33,34,35, 43,44,45, 46,47,48, 49,50,80, 81,82,99, 100 37,36,32, 33,34,35, 44,45,46, 47,48,49, 50,80,81, 82,92,99, 100 P4,N4, A2,C2, R2,T2, A3,B3, C3,T3, A5,B5, C5,T5, A6,B6, C6,R6, T6 BWA,BWB 93,94 93,94 G3,L5 B5,A4 InputByte Write Select Inputs, active LOW. Qualified Synchronous with BWE to conduct Byte Writes to the SRAM. Sampled on the rising edge of CLK. GW 88 88 H4 B7 InputGlobal Write Enable Input, active LOW. When Synchronous asserted LOW on the rising edge of CLK, a global Write is conducted (ALL bytes are written, regardless of the values on BWX and BWE). BWE 87 87 M4 A7 InputByte Write Enable Input, active LOW. Sampled Synchronous on the rising edge of CLK. This signal must be asserted LOW to conduct a Byte Write. CLK 89 89 K4 B6 98 98 E4 A3 InputChip Enable 1 Input, active LOW. Sampled on Synchronous the rising edge of CLK. Used in conjunction with CE2 and CE3[2] to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE2 97 97 B2 B3 InputChip Enable 2 Input, active HIGH. Sampled on Synchronous the rising edge of CLK. Used in conjunction with CE1 and CE3[2] to select/deselect the device. CE3 [2] 92 - - A6 InputChip Enable 3 Input, active LOW. Sampled on Synchronous the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. Not available for AJ package version. Not connected for BGA. Where referenced, CE3[2] is assumed active throughout this document for BGA. OE 86 86 F4 B8 InputOutput Enable, asynchronous input, active Asynchronous LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a Read cycle when emerging from a deselected state. ADV 83 83 G4 A9 InputAdvance Input signal, sampled on the rising Synchronous edge of CLK, active LOW. When asserted, it automatically increments the address in a burst cycle. Name CE1 Document #: 38-05291 Rev. *C BGA fBGA I/O Description InputAddress Inputs used to select one of the 512K R6,P6,A2, A10,A11, Synchronous address locations. Sampled at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, B2,B10,P3, P4,P8,P9, CE2, and CE3[2] are sampled active. A1, A0 are fed P10,P11, to the two-bit counter.. R3,R4,R8, R9,R10, R11 InputClock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. Page 9 of 34 CY7C1360B CY7C1362B CY7C1362B–Pin Definitions (continued) TQFP 3-Chip Enable TQFP 2-Chip Enable BGA fBGA 84 84 A4 B9 InputAddress Strobe from Processor, sampled on Synchronous the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A1, A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC 85 85 P4 A8 InputAddress Strobe from Controller, sampled on Synchronous the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A1, A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ZZ 64 64 T7 H11 InputZZ “Sleep” Input, active HIGH. When asserted Asynchronous HIGH places the device in a non-time-critical “sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. Name ADSP I/O Description DQs, DQPs 58,59,62, 63,68,69, 72,73,8,9, 12,13,18, 19,22,23, 74,24 I/OBidirectional Data I/O lines. As inputs, they feed J10,K10, P7,K7, 58,59,62, L10,M10, Synchronous into an on-chip data register that is triggered by the G7,E7, 63,68,69, rising edge of CLK. As outputs, they deliver the 72,73,8,9, F6,H6,L6, D11,E11, data contained in the memory location specified by N6,D1, F11,G11,J1, 12,13,18, the addresses presented during the previous clock H1,L1, K1,L1,M1,D 19,22,23, 2,E2,F2, N1,E2, 74,24 rise of the a Read cycle. The direction of the pins G2,K2, G2,C11,N1 is controlled by OE. When OE is asserted LOW, M2,D6, the pins behave as outputs. When HIGH, DQs and P2 DQPX are placed in a three-state condition. VDD 15,41,65, 91 15,41,65, 91 VSS 17,40,67, 90 17,40,67, D3,D5, 90 E5,E3,F3, F5,G5, H3,H5, K3,K5,L3, M3,M5, N3,N5, P3,P5 VSSQ 5,10,21,26, 5,10,21,26, 55,60,71, 55,60,71, 76 76 Document #: 38-05291 Rev. *C C4,J2,J4, D4,D8,E4,E Power Supply Power supply inputs to the core of the device. J6,R4 8,F4,F8, G4,G8,H4, H8,J4,J8, K4,K8,L4, L8,M4,M8 - H2,C4,C5, C6,C7,C8, D5,D6,D7,E 5,E6,E7, F5,F6,F7, G5,G6,G7, H5,H6,H7,J 5,J6,J7, K5,K6,K7, L5,L6,L7, M5,M6,M7, N4,N8 Ground - I/O Ground Ground for the core of the device. Ground for the I/O circuitry. Page 10 of 34 CY7C1360B CY7C1362B CY7C1362B–Pin Definitions (continued) Name VDDQ MODE TQFP 3-Chip Enable TQFP 2-Chip Enable BGA fBGA 4,11,20,27, 4,11,20,27, A1,A7,F1, C3,C9,D3, 54,61,70, 54,61,70, F7,J1,J7, D9,E3,E9, 77 77 M1,M7, F3,F9,G3, U1,U7 G9,J3,J9, K3,K9,L3, L9,M3,M9, N3,N9 I/O I/O Power Supply Power supply for the I/O circuitry. 31 31 R3 R1 TDO - - U5 P7 TDI - - U3 P5 JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not input Synchronous being utilized, this pin can be left floating or connected to VDD through a pull-up resistor. This pin is not available on TQFP packages. TMS - - U2 R5 JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not input Synchronous being utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP packages. TCK - - U4 R7 JTAG-Clock NC 1,2,3,6,7, 14,16,25, 28,29,30, 38,39,42, 51,52,53, 56,57,66, 75,78,79, 95,96 1,2,3,6,7, 14,16,25, 28,29,30, 38,39,42, 43,51,52, 53,56,57, 66,75,78, 79,95,96 B1,B7, C1,C7, D2,D4, D7,E1, E6,H2, F2,G1, G6,H7, J3,J5,K1, K6,L4,L2, L7,M6, N2,L7,P1, P6,R1, R5,R7, T1,T4,U6 A5,B1,B4, C1,C2,C10, D1,D10, E1,E10,F1, F10,G1, G10,H1,H3, H9,H10,J2, J11,K2, K11,L2,L1, M2,M11, N2,N7,N10, N5,N11,P1, A1,B11,P2, R2,N6 - Document #: 38-05291 Rev. *C InputStatic Description JTAG serial output Synchronous Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode pin has an internal pull-up. Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG feature is not being utilized, this pin should be left unconnected. This pin is not available on TQFP packages. Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must be connected to VSS. This pin is not available on TQFP packages. No Connects. Not internally connected to the die. Page 11 of 34 CY7C1360B CY7C1362B Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (tCO) is 3.0 ns (200-MHz device). The CY7C1360B/CY7C1362B supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium and i486 processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the Processor Address Strobe (ADSP) or the Controller Address Strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte Write operations are qualified with the Byte Write Enable (BWE) and Byte Write Select (BWX) inputs. A Global Write Enable (GW) overrides all Byte Write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self-timed Write circuitry. Three synchronous Chip Selects (CE1, CE2, CE3[2]) and an asynchronous Output Enable (OE) provide for easy bank selection and output three-state control. ADSP is ignored if CE1 is HIGH. Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2) CE1, CE2, CE3[2] are all asserted active, and (3) the Write signals (GW, BWE) are all deasserted HIGH. ADSP is ignored if CE1 is HIGH. The address presented to the address inputs (A) is stored into the address advancement logic and the address register while being presented to the memory array. The corresponding data is allowed to propagate to the input of the output registers. At the rising edge of the next clock the data is allowed to propagate through the output register and onto the data bus within 3.0 ns (200-MHz device) if OE is active LOW. The only exception occurs when the SRAM is emerging from a deselected state to a selected state, its outputs are always three-stated during the first cycle of the access. After the first cycle of the access, the outputs are controlled by the OE signal. Consecutive single Read cycles are supported. Once the SRAM is deselected at clock rise by the chip select and either ADSP or ADSC signals, its output will three-state immediately. Single Write Accesses Initiated by ADSP This access is initiated when both of the following conditions are satisfied at clock rise: (1) ADSP is asserted LOW, and (2) CE1, CE2, CE3[2] are all asserted active. The address presented to A is loaded into the address register and the address advancement logic while being delivered to the memory array. The Write signals (GW, BWE, and BWX) and ADV inputs are ignored during this first cycle. ADSP-triggered Write accesses require two clock cycles to complete. If GW is asserted LOW on the second clock rise, the data presented to the DQs inputs is written into the corresponding address location in the memory array. If GW is HIGH, Document #: 38-05291 Rev. *C then the Write operation is controlled by BWE and BWX signals. The CY7C1360B/CY7C1362B provides Byte Write capability that is described in the Write Cycle Descriptions table. Asserting the Byte Write Enable input (BWE) with the selected Byte Write (BWX) input, will selectively write to only the desired bytes. Bytes not selected during a Byte Write operation will remain unaltered. A synchronous self-timed Write mechanism has been provided to simplify the Write operations. Because the CY7C1360B/CY7C1362B is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQs inputs. Doing so will three-state the output drivers. As a safety precaution, DQs are automatically three-stated whenever a Write cycle is detected, regardless of the state of OE. Single Write Accesses Initiated by ADSC ADSC Write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted HIGH, (3) CE1, CE2, CE3[2] are all asserted active, and (4) the appropriate combination of the Write inputs (GW, BWE, and BWX) are asserted active to conduct a Write to the desired byte(s). ADSC-triggered Write accesses require a single clock cycle to complete. The address presented to A is loaded into the address register and the address advancement logic while being delivered to the memory array. The ADV input is ignored during this cycle. If a global Write is conducted, the data presented to the DQs is written into the corresponding address location in the memory core. If a Byte Write is conducted, only the selected bytes are written. Bytes not selected during a Byte Write operation will remain unaltered. A synchronous self-timed Write mechanism has been provided to simplify the Write operations. Because the CY7C1360B/CY7C1362B is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQs inputs. Doing so will three-state the output drivers. As a safety precaution, DQs are automatically three-stated whenever a Write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1360B/CY7C1362B provides a two-bit wraparound counter, fed by A1, A0, that implements either an interleaved or linear burst sequence. The interleaved burst sequence is designed specifically to support Intel Pentium applications. The linear burst sequence is designed to support processors that follow a linear burst sequence. The burst sequence is user selectable through the MODE input. Asserting ADV LOW at clock rise will automatically increment the burst counter to the next address in the burst sequence. Both Read and Write burst operations are supported. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CE1, CE2, CE3[2], ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Page 12 of 34 CY7C1360B CY7C1362B Interleaved Burst Address Table (MODE = Floating or VDD) Linear Burst Address Table (MODE = GND) First Address A1, A0 Second Address A1, A0 Third Address A1, A0 Fourth Address A1, A0 First Address A1, A0 Second Address A1, A0 Third Address A1, A0 Fourth Address A1, A0 00 01 10 11 00 01 10 11 01 00 11 10 01 10 11 00 10 11 00 01 10 11 00 01 11 10 01 00 11 00 01 10 . ZZ Mode Electrical Characteristics Parameter Description Test Conditions Min. Max. Unit IDDZZ Snooze mode standby current ZZ > VDD – 0.2V 35 mA tZZS Device operation to ZZ ZZ > VDD – 0.2V 2tCYC ns tZZREC ZZ recovery time ZZ < 0.2V tZZI ZZ Active to snooze current This parameter is sampled tRZZI ZZ Inactive to exit snooze current This parameter is sampled Document #: 38-05291 Rev. *C 2tCYC ns 2tCYC 0 ns ns Page 13 of 34 CY7C1360B CY7C1362B Truth Table[3, 4, 5, 6, 7, 8] Operation Deselect Cycle, Power Down Add. Used CE1 None H CE2 CE3 DQ ZZ ADSP ADSC ADV WRITE OE CLK L X L X X X L-H Three-State X X Deselect Cycle, Power Down None L L X L Deselect Cycle, Power Down None L X H Deselect Cycle, Power Down None L L X L X X X X L-H Three-State L L X X X X L-H Three-State L H L X X X L-H Three-State Deselect Cycle, Power Down None L X H L H L X X X L-H Three-State Snooze Mode, Power Down None X X X H X X X X X X Three-State READ Cycle, Begin Burst External L H L L L X X X L L-H Q READ Cycle, Begin Burst External L H L L L X X X H L-H Three-State WRITE Cycle, Begin Burst External L H L L H L X L X L-H D READ Cycle, Begin Burst External L H L L H L X H L L-H Q READ Cycle, Begin Burst External L H L L H L X H H L-H Three-State READ Cycle, Continue Burst Next X X X L H H L H L L-H Q READ Cycle, Continue Burst Next X X X L H H L H H L-H Three-State READ Cycle, Continue Burst Next H X X L X H L H L L-H Q READ Cycle, Continue Burst Next H X X L X H L H H L-H Three-State WRITE Cycle, Continue Burst Next X X X L H H L L X L-H D WRITE Cycle, Continue Burst Next H X X L X H L L X L-H D READ Cycle, Suspend Burst Current X X X L H H H H L L-H Q READ Cycle, Suspend Burst Current X X X L H H H H H L-H Three-State READ Cycle, Suspend Burst Current H X X L X H H H L L-H Q READ Cycle, Suspend Burst Current H X X L X H H H H L-H Three-State WRITE Cycle, Suspend Burst Current X X X L H H H L X L-H D WRITE Cycle, Suspend Burst Current H X X L X H H L X L-H D Notes: 3. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. 4. WRITE = L when any one or more Byte Write Enable signals and BWE = L or GW = L. WRITE = H when all Byte Write Enable signals, BWE, GW = H. 5. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 6. CE1, CE2, and CE3 are available only in the TQFP package. BGA package has only 2 chip selects CE1 and CE2. 7. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the Write cycle to allow the outputs to three-state. OE is a don't care for the remainder of the Write cycle 8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during Write cycles. During a Read cycle all data bits are Three-State when OE is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW). 9. Table only lists a partial listing of the byte write combinations. Any combination of BW[A:D] is valid. Appropriate write will be done based on which byte write is active. Document #: 38-05291 Rev. *C Page 14 of 34 CY7C1360B CY7C1362B Partial Truth Table for Read/Write[5, 9] Function (CY7C1360B) Read Read Write Byte A – (DQA and DQPA) Write Byte B – (DQB and DQPB) Write Bytes B, A Write Byte C – (DQC and DQPC) Write Bytes C, A Write Bytes C, B Write Bytes C, B, A Write Byte D – (DQD and DQPD) Write Bytes D, A Write Bytes D, B Write Bytes D, B, A Write Bytes D, C Write Bytes D, C, A Write Bytes D, C, B Write All Bytes Write All Bytes GW H H H H H H H H H H H H H H H H H L BWE H L L L L L L L L L L L L L L L L X BWD X H H H H H H H H L L L L L L L L X BWC X H H H H L L L L H H H H L L L L X BWB X H H L L H H L L H H L L H H L L X BWA X H L H L H L H L H L H L H L H L X Truth Table for Read/Write[5] Function (CY7C1362B) Read Read Write Byte A – (DQA and DQPA) Write Byte B – (DQB and DQPB) Write Bytes B, A Write All Bytes Write All Bytes Document #: 38-05291 Rev. *C GW H H H H H H L BWE H L L L L L X BWB X H H L L L X BWA X H L H L L X Page 15 of 34 CY7C1360B CY7C1362B IEEE 1149.1 Serial Boundary Scan (JTAG) Test MODE SELECT (TMS) The CY7C1360B/CY7C1362B incorporates a serial boundary scan test access port (TAP). This port operates in accordance with IEEE Standard 1149.1-1990 but does not have the set of functions required for full 1149.1 compliance. These functions from the IEEE specification are excluded because their inclusion places an added delay in the critical speed path of the SRAM. Note that the TAP controller functions in a manner that does not conflict with the operation of other devices using 1149.1 fully compliant TAPs. The TAP operates using JEDEC-standard 3.3V or 2.5V I/O logic levels. The CY7C1360B/CY7C1362B contains a TAP controller, instruction register, boundary scan register, bypass register, and ID register. Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull-up resistor. TDO should be left unconnected. Upon power-up, the device will come up in a reset state which will not interfere with the operation of the device. The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this ball unconnected if the TAP is not used. The ball is pulled up internally, resulting in a logic HIGH level. Test Data-In (TDI) The TDI ball is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see Figure . TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) of any register. (See Tap Controller Block Diagram.) Test Data-Out (TDO) The TDO output ball is used to serially clock data-out from the registers. The output is active depending upon the current state of the TAP state machine. The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. (See Tap Controller State Diagram.) TAP Controller Block Diagram TAP Controller State Diagram 1 0 Bypass Register TEST-LOGIC RESET 2 1 0 0 0 RUN-TEST/ IDLE 1 SELECT DR-SCAN 1 SELECT IR-SCAN 0 1 1 CAPTURE-DR 0 TDO x . . . . . 2 1 0 SHIFT-IR 0 Boundary Scan Register 1 EXIT1-DR 1 EXIT1-IR 0 1 TCK 0 PAUSE-DR 0 PAUSE-IR 1 0 TMS TAP CONTROLLER 1 EXIT2-DR 0 EXIT2-IR 1 Performing a TAP Reset 1 UPDATE-DR 0 UPDATE-IR 1 0 The 0/1 next to each state represents the value of TMS at the rising edge of TCK. Test Access Port (TAP) Test Clock (TCK) The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Document #: 38-05291 Rev. *C Selection Circuitry Identification Register CAPTURE-IR 1 Instruction Register 31 30 29 . . . 2 1 0 0 SHIFT-DR 1 TDI Selection Circuitry 0 0 0 1 A RESET is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power-up, the TAP is reset internally to ensure that TDO comes up in a High-Z state. TAP Registers Registers are connected between the TDI and TDO balls and allow data to be scanned into and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction register. Data is serially loaded into the TDI ball on the rising edge of TCK. Data is output on the TDO ball on the falling edge of TCK. Page 16 of 34 CY7C1360B CY7C1362B Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO balls as shown in the Tap Controller Block Diagram. Upon power-up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the Capture-IR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board-level serial test data path. Bypass Register Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO balls. To execute the instruction once it is shifted in, the TAP controller needs to be moved into the Update-IR state. EXTEST EXTEST is a mandatory 1149.1 instruction which is to be executed whenever the instruction register is loaded with all 0s. EXTEST is not implemented in this SRAM TAP controller, and therefore this device is not compliant to 1149.1. The TAP controller does recognize an all-0 instruction. To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between the TDI and TDO balls. This allows data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. When an EXTEST instruction is loaded into the instruction register, the SRAM responds as if a SAMPLE/PRELOAD instruction has been loaded. There is one difference between the two instructions. Unlike the SAMPLE/PRELOAD instruction, EXTEST places the SRAM outputs in a High-Z state. Boundary Scan Register IDCODE The boundary scan register is connected to all the input and bidirectional balls on the SRAM. The SRAM has a 71-bit-long register. The boundary scan register is loaded with the contents of the RAM I/O ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO balls when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the I/O ring. The Boundary Scan Order tables show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI and the LSB is connected to TDO. Identification (ID) Register The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO balls and allows the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power-up or whenever the TAP controller is given a test logic reset state. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO balls when the TAP controller is in a Shift-DR state. It also places all SRAM outputs into a High-Z state. SAMPLE/PRELOAD The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions table. SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The PRELOAD portion of this instruction is not implemented, so the device TAP controller is not fully 1149.1 compliant. TAP Instruction Set The user must be aware that the TAP controller clock can only operate at a frequency up to 10 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output will undergo a transition. The TAP may then try to capture a signal while in transition (metastable state). This will not harm the device, but there is no guarantee as to the value that will be captured. Repeatable results may not be possible. Overview Eight different instructions are possible with the three-bit instruction register. All combinations are listed in the Instruction Codes table. Three of these instructions are listed as RESERVED and should not be used. The other five instructions are described in detail below. The TAP controller used in this SRAM is not fully compliant to the 1149.1 convention because some of the mandatory 1149.1 instructions are not fully implemented. The TAP controller cannot be used to load address data or control signals into the SRAM and cannot preload the I/O buffers. The SRAM does not implement the 1149.1 commands EXTEST or INTEST or the PRELOAD portion of SAMPLE/PRELOAD; rather, it performs a capture of the I/O ring when these instructions are executed. Document #: 38-05291 Rev. *C When the SAMPLE/PRELOAD instruction is loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the inputs and bidirectional balls is captured in the boundary scan register. To guarantee that the boundary scan register will capture the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller’s capture set-up plus hold time (tCS plus tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is still Page 17 of 34 CY7C1360B CY7C1362B BYPASS possible to capture all other signals and simply ignore the value of the CLK captured in the boundary scan register. When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO balls. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. Once the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO balls. Note that since the PRELOAD part of the command is not implemented, putting the TAP to the Update-DR state while performing a SAMPLE/PRELOAD instruction will have the same effect as the Pause-DR command. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. TAP Timing 1 2 Test Clock (TCK) 3 t TH t TMSS t TMSH t TDIS t TDIH t TL 4 5 6 t CYC Test Mode Select (TMS) Test Data-In (TDI) t TDOV t TDOX Test Data-Out (TDO) DON’T CARE UNDEFINED TAP AC Switching Characteristics Over the Operating Range[10, 11] Parameter Description Min. Max. Unit 20 MHz Clock tTCYC TCK Clock Cycle Time tTF TCK Clock Frequency tTH TCK Clock HIGH time 25 ns tTL TCK Clock LOW time 25 ns 50 ns Output Times tTDOV TCK Clock LOW to TDO Valid tTDOX TCK Clock LOW to TDO Invalid 5 ns 0 ns Set-up Times tTMSS TMS Set-up to TCK Clock Rise 5 ns tTDIS TDI Set-up to TCK Clock Rise 5 ns tCS Capture Set-up to TCK Rise 5 tTMSH TMS hold after TCK Clock Rise 5 tTDIH TDI Hold after Clock Rise 5 ns tCH Capture Hold after Clock Rise 5 ns Hold Times ns Notes: 10. tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register. 11. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1ns. Document #: 38-05291 Rev. *C Page 18 of 34 CY7C1360B CY7C1362B 3.3V TAP AC Test Conditions 2.5V TAP AC Test Conditions Input pulse levels ........ ........................................VSS to 3.3V Input pulse levels......... ........................................VSS to 2.5V Input rise and fall times ..................... ..............................1 ns Input rise and fall time .....................................................1 ns Input timing reference levels ...........................................1.5V Input timing reference levels................... ......................1.25V Output reference levels...................................................1.5V Output reference levels .................. ..............................1.25V Test load termination supply voltage...............................1.5V Test load termination supply voltage .................... ........1.25V 3.3V TAP AC Output Load Equivalent 2.5V TAP AC Output Load Equivalent 1.5V 1.25V 50Ω 50Ω TDO TDO Z O= 50Ω Z O= 50Ω 20pF 20pF TAP DC Electrical Characteristics And Operating Conditions (0°C < TA < +70°C; VDD = 3.3V ±0.165V unless otherwise noted)[12] Parameter Description Conditions VOH1 Output HIGH Voltage IOH = –4.0 mA VOH2 Output HIGH Voltage VOL1 Output LOW Voltage IOL = 8.0 mA VOL2 Output LOW Voltage VIH Input HIGH Voltage VIL Input LOW Voltage IX Input Load Current Min. Max. Unit VDDQ = 3.3V 2.4 V IOH = –1.0 mA VDDQ = 2.5V 2.0 V IOH = –100 µA VDDQ = 3.3V 2.9 V VDDQ = 2.5V 2.1 V VDDQ = 3.3V 0.4 V IOL = 8.0 mA VDDQ = 2.5V 0.4 V IOL = 100 µA VDDQ = 3.3V 0.2 V VDDQ = 2.5V 0.2 V 2.0 VDD + 0.3 V VDDQ = 2.5V 1.7 VDD + 0.3 V VDDQ = 3.3V –0.5 0.7 V VDDQ = 2.5V –0.3 0.7 V –5 5 µA VDDQ = 3.3V GND < VIN < VDDQ Note: 12. All voltages referenced to VSS (GND). Document #: 38-05291 Rev. *C Page 19 of 34 CY7C1360B CY7C1362B Identification Register Definitions CY7C1360B (256KX36) CY7C1362B (512KX18) 001 001 Device Depth (28:24) 01010 01010 Reserved for Internal Use Device Width (23:18) 000000 000000 Defines memory type and architecture Cypress Device ID (17:12) 100110 010110 Defines width and density 00000110100 00000110100 1 1 Instruction Field Revision Number (31:29) Cypress JEDEC ID Code (11:1) ID Register Presence Indicator (0) Description Describes the version number Allows unique identification of SRAM vendor Indicates the presence of an ID register Scan Register Sizes Bit Size(x36) Bit Size(x18) Instruction 3 3 Bypass 1 1 Register Name ID 32 32 Boundary Scan Order 71 71 Identification Codes Instruction Code Description EXTEST 000 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces all SRAM outputs to High-Z state. This instruction is not 1149.1 compliant. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operations. SAMPLE Z 010 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a High-Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Does not affect SRAM operation. This instruction does not implement 1149.1 preload function and is therefore not 1149.1 compliant. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operations. Document #: 38-05291 Rev. *C Page 20 of 34 CY7C1360B CY7C1362B 119-Ball BGA Boundary Scan Order CY7C1360B (256K x 36) CY7C1362B (512K x 18) BIT # BALL ID Signal Name BIT # BALL ID Signal Name BIT# BALL ID Signal Name BIT# BALL ID Signal Name 1 K4 CLK 37 P4 A0 1 K4 CLK 37 P4 A0 2 H4 GW 38 N4 A1 2 H4 GW 38 N4 A1 3 M4 BWE 39 R6 A 3 M4 BWE 39 R6 A 4 F4 OE 40 T5 A 4 F4 OE 40 T5 A 5 B4 ADSC 41 T3 A 5 B4 ADSC 41 T3 A 6 A4 ADSP 42 R2 A 6 A4 ADSP 42 R2 A 7 G4 ADV 43 R3 MODE 7 G4 ADV 43 R3 MODE 8 C3 A 44 P2 DQPD 8 C3 A 44 Internal Internal 9 B3 A 45 P1 DQD 9 B3 A 45 Internal Internal 10 D6 DQPB 46 L2 DQD 10 T2 A 46 Internal Internal 11 H7 DQB 47 K1 DQD 11 Internal Internal 47 Internal Internal 12 G6 DQB 48 N2 DQD 12 Internal Internal 48 P2 DQPB 13 E6 DQB 49 N1 DQD 13 Internal Internal 49 N1 DQB 14 D7 DQB 50 M2 DQD 14 D6 DQPA 50 M2 DQB 15 E7 DQB 51 L1 DQD 15 E7 DQA 51 L1 DQB 16 F6 DQB 52 K2 DQD 16 F6 DQA 52 K2 DQB 17 G7 DQB 53 Internal Internal 17 G7 DQA 53 Internal Internal 18 H6 DQB 54 H1 DQC 18 H6 DQA 54 H1 DQB 19 T7 ZZ 55 G2 DQC 19 T7 ZZ 55 G2 DQB 20 K7 DQA 56 E2 DQC 20 K7 DQA 56 E2 DQB 21 L6 DQA 57 D1 DQC 21 L6 DQA 57 D1 DQB 22 N6 DQA 58 H2 DQC 22 N6 DQA 58 Internal Internal 23 P7 DQA 59 G1 DQC 23 P7 DQA 59 Internal Internal 24 N7 DQA 60 F2 DQC 24 Internal Internal 60 Internal Internal 25 M6 DQA 61 E1 DQC 25 Internal Internal 61 Internal Internal 26 L7 DQA 62 D2 DQPC 26 Internal Internal 62 Internal Internal 27 K6 DQA 63 C2 A 27 Internal Internal 63 C2 A 28 P6 DQPA 64 A2 A 28 Internal Internal 64 A2 A 29 T4 A 65 E4 CE1 29 T6 A 65 E4 CE1 30 A3 A 66 B2 CE2 30 A3 A 66 B2 CE2 31 C5 A 67 L3 BWD 31 C5 A 67 Internal Internal 32 B5 A 68 G3 BWC 32 B5 A 68 Internal Internal 33 A5 A 69 G5 BWB 33 A5 A 69 G3 BWB 34 C6 A 70 L5 BWA 34 C6 A 70 L5 BWA 35 A6 A 71 Internal Internal 35 A6 A 71 Internal Internal 36 B6 A 36 B6 A Document #: 38-05291 Rev. *C Page 21 of 34 CY7C1360B CY7C1362B 165-Ball fBGA Boundary Scan Order CY7C1360B (256K x 36) CY7C1362B (512K x 18) BIT# BALL ID Signal Name BIT# BALL ID Signal Name BIT# BALL ID Signal Name BIT# BALL ID Signal Name 1 B6 CLK 37 R6 A0 1 B6 CLK 37 R6 A0 2 B7 GW 38 P6 A1 2 B7 GW 38 P6 A1 3 A7 BWE 39 R4 A 3 A7 BWE 39 R4 A 4 B8 OE 40 P4 A 4 B8 OE 40 P4 A 5 A8 ADSC 41 R3 A 5 A8 ADSC 41 R3 A 6 B9 ADSP 42 P3 A 6 B9 ADSP 42 P3 A 7 A9 ADV 43 R1 MODE 7 A9 ADV 43 R1 MODE 8 B10 A 44 N1 DQPD 8 B10 A 44 Internal Internal 9 A10 A 45 L2 DQD 9 A10 A 45 Internal Internal 10 C11 DQPB 46 K2 DQD 10 A11 A 46 Internal Internal 11 E10 DQB 47 J2 DQD 11 Internal Internal 47 Internal Internal 12 F10 DQB 48 M2 DQD 12 Internal Internal 48 N1 DQPB 13 G10 DQB 49 M1 DQD 13 Internal Internal 49 M1 DQB 14 D10 DQB 50 L1 DQD 14 C11 DQPA 50 L1 DQB 15 D11 DQB 51 K1 DQD 15 D11 DQA 51 K1 DQB 16 E11 DQB 52 J1 DQD 16 E11 DQA 52 J1 DQB 17 F11 DQB 53 Internal Internal 17 F11 DQA 53 Internal Internal 18 G11 DQB 54 G2 DQC 18 G11 DQA 54 G2 DQB 19 H11 ZZ 55 F2 DQC 19 H11 ZZ 55 F2 DQB 20 J10 DQA 56 E2 DQC 20 J10 DQA 56 E2 DQB 21 K10 DQA 57 D2 DQC 21 K10 DQA 57 D2 DQB 22 L10 DQA 58 G1 DQC 22 L10 DQA 58 Internal Internal 23 M10 DQA 59 F1 DQC 23 M10 DQA 59 Internal Internal 24 J11 DQA 60 E1 DQC 24 Internal Internal 60 Internal Internal 25 K11 DQA 61 D1 DQC 25 Internal Internal 61 Internal Internal 26 L11 DQA 62 C1 DQPC 26 Internal Internal 62 Internal Internal 27 M11 DQA 63 B2 A 27 Internal Internal 63 B2 A 28 N11 DQPA 64 A2 A 28 Internal Internal 64 A2 A 29 R11 A 65 A3 CE1 29 R11 A 65 A3 CE1 30 R10 A 66 B3 CE2 30 R10 A 66 B3 CE2 31 P10 A 67 B4 BWD 31 P10 A 67 Internal Internal 32 R9 A 68 A4 BWC 32 R9 A 68 Internal Internal 33 P9 A 69 A5 BWB 33 P9 A 69 A4 BWB 34 R8 A 70 B5 BWA 34 R8 A 70 B5 BWA 35 P8 A 71 A6 CE3 35 P8 A 71 A6 CE3 36 P11 A 36 P11 A Document #: 38-05291 Rev. *C Page 22 of 34 CY7C1360B CY7C1362B Maximum Ratings Current into Outputs (LOW)......................................... 20 mA (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Ambient Temperature with Power Applied............................................. –55°C to +125°C Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V DC Voltage Applied to Outputs in Three-State ..................................... –0.5V to VDDQ + 0.5V DC Input Voltage....................................–0.5V to VDD + 0.5V Static Discharge Voltage........................................... >2001V (per MIL-STD-883, Method 3015) Latch-up Current..................................................... >200 mA Operating Range Ambient Range Temperature VDD VDDQ Commercial 0°C to +70°C 3.3V – 5%/+10% 2.5V – 5% to VDD Industrial –40°C to +85°C Electrical Characteristics Over the Operating Range[13, 14] Parameter Description VDD Power Supply Voltage VDDQ I/O Supply Voltage VOH VOL VIH VIL IX Output HIGH Voltage Output LOW Voltage Input HIGH Input LOW Voltage[13] Voltage[13] Input Load Current except ZZ and MODE Test Conditions Min. Max. Unit 3.135 3.6 V V VDDQ = 3.3V 3.135 VDD VDDQ = 2.5V 2.375 2.625 VDDQ = 3.3V, VDD = Min., IOH = –4.0 mA 2.4 V VDDQ = 2.5V, VDD = Min., IOH = –1.0 mA 2.0 V VDDQ = 3.3V, VDD = Min., IOL = 8.0 mA 0.4 V VDDQ = 2.5V, VDD = Min., IOL = 1.0 mA 0.4 V VDDQ = 3.3V 2.0 VDD + 0.3V V VDDQ = 2.5V 1.7 VDD + 0.3V V VDDQ = 3.3V –0.3 0.8 V VDDQ = 2.5V –0.3 0.7 V –5 5 µA GND ≤ VI ≤ VDDQ Input Current of MODE Input = VSS Input Current of ZZ 5 Input = VSS Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled IDD VDD Operating Supply Current VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC VDD = Max, Device Deselected, VIN ≥ VIH or VIN ≤ VIL f = fMAX = 1/tCYC µA µA –5 Input = VDD IOZ µA –30 Input = VDD 30 µA 5 µA 4.4-ns cycle, 225 MHz 250 mA 5-ns cycle, 200 MHz 220 mA 6-ns cycle, 166 MHz 180 mA All speeds 50 mA –5 ISB1 Automatic CE Power-down Current—TTL Inputs ISB2 Automatic CE VDD = Max, Device Deselected, Power-down VIN ≤ 0.3V or VIN > VDDQ – 0.3V, Current—CMOS Inputs f = 0 All speeds 30 mA ISB3 Automatic CE VDD = Max, Device Deselected, or All speeds Power-down VIN ≤ 0.3V or VIN > VDDQ – 0.3V Current—CMOS Inputs f = fMAX = 1/tCYC 50 mA ISB4 Automatic CE Power-down Current—TTL Inputs 40 mA VDD = Max, Device Deselected, VIN ≥ VIH or VIN ≤ VIL, f = 0 All Speeds Shaded areas contain advance information. Notes: 13. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2V (Pulse width less than tCYC/2). 14. TPower-up: Assumes a linear ramp from 0V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD. Document #: 38-05291 Rev. *C Page 23 of 34 CY7C1360B CY7C1362B Thermal Resistance[15] Parameter Description ΘJA Thermal Resistance (Junction to Ambient) ΘJC Thermal Resistance (Junction to Case) Test Conditions TQFP Package BGA Package fBGA Package Unit 25 25 27 °C/W 9 6 6 °C/W Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA / JESD51. Capacitance[15] Parameter Description Test Conditions CIN Input Capacitance CCLK Clock Input Capacitance CI/O Input/Output Capacitance TA = 25°C, f = 1 MHz, VDD = 3.3V. VDDQ = 2.5V TQFP Package BGA Package fBGA Package Unit 5 5 5 pF 5 5 5 pF 5 7 7 pF AC Test Loads and Waveforms 3.3V I/O Test Load R = 317Ω 3.3V OUTPUT OUTPUT RL = 50Ω Z0 = 50Ω GND 5 pF R = 351Ω INCLUDING JIG AND SCOPE 10% 90% 10% 90% ≤ 1 ns ≤ 1 ns VL = 1.5V (a) ALL INPUT PULSES VDD (c) (b) 2.5V I/O Test Load R = 1667Ω 2.5V OUTPUT OUTPUT RL = 50Ω Z0 = 50Ω GND 5 pF R =1538Ω VL = 1.25V (a) ALL INPUT PULSES VDD INCLUDING JIG AND SCOPE (b) 10% 90% 10% 90% ≤ 1 ns ≤ 1 ns (c) Note: 15. Tested initially and after any design or process change that may affect these parameters. Document #: 38-05291 Rev. *C Page 24 of 34 CY7C1360B CY7C1362B Switching Characteristics Over the Operating Range[16, 17] 225 MHz Parameter tPOWER Description VDD(Typical) to the First Access[18] Min. Max 200 MHz Min. Max 166 MHz Min. Max Unit 1 1 1 ms Clock tCYC Clock Cycle Time 4.4 5.0 6.0 ns tCH Clock HIGH 1.8 2.0 2.4 ns tCL Clock LOW 1.8 2.0 2.4 ns Output Times tCO Data Output Valid after CLK Rise tDOH Data Output Hold after CLK Rise 1.25 1.25 1.25 ns tCLZ Clock to Low-Z[19, 20, 21] 1.25 1.25 1.25 ns tCHZ High-Z[19, 20, 21] 1.25 tOEV tOELZ tOEHZ Clock to OE LOW to Output Valid OE LOW to Output Low-Z[19, 20, 21] 2.8 2.8 3.0 1.25 2.8 0 [19, 20, 21] 1.25 3.0 0 2.8 OE HIGH to Output High-Z 3.0 3.5 3.5 ns 3.5 ns 0 3.0 ns ns 3.5 ns Set-up Times tAS Address Set-up before CLK Rise 1.4 1.5 1.5 ns tADS ADSC, ADSP Set-up before CLK Rise 1.4 1.5 1.5 ns 1.5 1.5 ns tWES ADV Set-up before CLK Rise GW, BWE, BWX Set-up before CLK Rise 1.4 1.4 1.5 1.5 ns tDS Data Input Set-up before CLK Rise 1.4 1.5 1.5 ns tCES Chip Enable Set-Up before CLK Rise 1.4 1.5 1.5 ns Address Hold after CLK Rise 0.4 0.5 0.5 ns 0.5 0.5 ns 0.4 0.5 0.5 ns tWEH ADSP , ADSC Hold after CLK Rise ADV Hold after CLK Rise GW,BWE, BWX Hold after CLK Rise 0.4 0.4 0.5 0.5 ns tDH Data Input Hold after CLK Rise 0.4 0.5 0.5 ns tCEH Chip Enable Hold after CLK Rise 0.4 0.5 0.5 ns tADVS Hold Times tAH tADH tADVH Shaded areas contain advance information. Notes: 16. Timing reference level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V. 17. Test conditions shown in (a) of AC Test Loads unless otherwise noted. 18. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a Read or Write operation can be initiated. 19. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage. 20. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve High-Z prior to Low-Z under the same system conditions 21. This parameter is sampled and not 100% tested. Document #: 38-05291 Rev. *C Page 25 of 34 CY7C1360B CY7C1362B Switching Waveforms Read Cycle Timing[22] t CYC CLK t CH t ADS t CL t ADH ADSP tADS tADH ADSC tAS tAH A1 ADDRESS A2 tWES A3 Burst continued with new base address tWEH GW, BWE, BWx tCES Deselect cycle tCEH CE tADVS tADVH ADV ADV suspends burst. OE t OEHZ t CLZ Data Out (Q) Q(A1) High-Z tOEV tCO t OELZ tDOH Q(A2) t CHZ Q(A2 + 1) Q(A2 + 2) Q(A2 + 3) Q(A2) Q(A2 + 1) t CO Burst wraps around to its initial state Single READ BURST READ DON’T CARE UNDEFINED Note: 22. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. Document #: 38-05291 Rev. *C Page 26 of 34 CY7C1360B CY7C1362B Switching Waveforms(continued) Write Cycle Timing[22, 23] t CYC CLK tCH tADS tCL tADH ADSP tADS ADSC extends burst tADH tADS tADH ADSC tAS tAH A1 ADDRESS A2 A3 Byte write signals are ignored for first cycle when ADSP initiates burst tWES tWEH BWE, BWX tWES tWEH GW tCES tCEH CE t t ADVS ADVH ADV ADV suspends burst OE tDS Data In (D) High-Z t OEHZ tDH D(A1) D(A2) D(A2 + 1) D(A2 + 1) D(A2 + 2) D(A2 + 3) D(A3) D(A3 + 1) D(A3 + 2) Data Out (Q) BURST READ Single WRITE BURST WRITE DON’T CARE Extended BURST WRITE UNDEFINED Note: 23. Full width Write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BWX LOW. Document #: 38-05291 Rev. *C Page 27 of 34 CY7C1360B CY7C1362B Switching Waveforms(continued) Read/Write Cycle Timing[22, 24, 25] tCYC CLK tCL tCH tADS tADH tAS tAH ADSP ADSC ADDRESS A1 A2 A3 A4 A5 A6 D(A5) D(A6) tWES tWEH BWE, BWX tCES tCEH CE ADV OE tDS tCO tDH tOELZ Data In (D) High-Z tCLZ Data Out (Q) High-Z Q(A1) Back-to-Back READs tOEHZ D(A3) Q(A2) Q(A4) Single WRITE Q(A4+1) Q(A4+2) BURST READ DON’T CARE Q(A4+3) Back-to-Back WRITEs UNDEFINED Notes: 24. The data bus (Q) remains in high-Z following a Write cycle, unless a new Read access is initiated by ADSP or ADSC. 25. GW is HIGH. Document #: 38-05291 Rev. *C Page 28 of 34 CY7C1360B CY7C1362B Switching Waveforms(continued) ZZ Mode Timing [26, 27] CLK t ZZ ZZ I t ZZREC t ZZI SUPPLY I DDZZ t RZZI ALL INPUTS (except ZZ) DESELECT or READ Only Outputs (Q) High-Z DON’T CARE Notes: 26. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device. 27. DQs are in High-Z when exiting ZZ sleep mode. Ordering Information Speed (MHz) 225 Ordering Code CY7C1360B-225AC CY7C1362B-225AC Package Name A101 Part and Package Type 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables CY7C1360B-225AI CY7C1362B-225AI CY7C1360B-225AJC Operating Range Commercial Industrial A101 CY7C1362B-225AJC 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables CY7C1360B-225AJI Commercial Industrial CY7C1362B-225AJI CY7C1360B-225BGC BG119 CY7C1362B-225BGC 119-ball (14 x 22 x 2.4 mm) BGA 2 Chip Enables and JTAG CY7C1360B-225BGI Commercial Industrial CY7C1362B-225BGI CY7C1360B-225BZC CY7C1362B-225BZC BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG CY7C1360B-225BZI Commercial Industrial CY7C1362B-225BZI Shaded areas contain advance information. Please contact your local sales representative for availability of these parts. Document #: 38-05291 Rev. *C Page 29 of 34 CY7C1360B CY7C1362B Ordering Information (continued) Speed (MHz) 200 Ordering Code CY7C1360B-200AC CY7C1362B-200AC Package Name A101 Part and Package Type 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables CY7C1360B-200AI CY7C1362B-200AI CY7C1360B-200AJC Operating Range Commercial Industrial A101 CY7C1362B-200AJC 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables CY7C1360B-200AJI Commercial Industrial CY7C1362B-200AJI CY7C1360B-200BGC BG119 CY7C1362B-200BGC 119-ball (14 x 22 x 2.4 mm) BGA 2 Chip Enables and JTAG CY7C1360B-200BGI Commercial Industrial CY7C1362B-200BGI CY7C1360B-200BZC BB165A CY7C1362B-200BZC 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG CY7C1360B-200BZI Commercial Industrial CY7C1362B-200BZI 166 CY7C1360B-166AC A101 CY7C1362B-166AC 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables CY7C1360B-166AI Commercial Industrial CY7C1362B-166AI CY7C1360B-166AJC A101 CY7C1362B-166AJC 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables CY7C1360B-166AJI Commercial Industrial CY7C1362B-166AJI CY7C1360B-166BGC BG119 CY7C1362B-166BGC 119-ball (14 x 22 x 2.4 mm) BGA 2 Chip Enables and JTAG CY7C1360B-166BGI Commercial Industrial ICY7C1362B-166BGI CY7C1360B-166BZC CY7C1362B-166BZC BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG CY7C1360B-166BZI Commercial Industrial CY7C1362B-166BZI Shaded areas contain advance information. Please contact your local sales representative for availability of these parts. Document #: 38-05291 Rev. *C Page 30 of 34 CY7C1360B CY7C1362B Package Diagrams 100-pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101 51-85050-A Document #: 38-05291 Rev. *C Page 31 of 34 CY7C1360B CY7C1362B Package Diagrams (continued) 119-Lead PBGA (14 x 22 x 2.4 mm) BG119 51-85115-*B Document #: 38-05291 Rev. *C Page 32 of 34 CY7C1360B CY7C1362B Package Diagrams (continued) 165-Ball FBGA (13 x 15 x 1.2 mm) BB165A 51-85122-*C i486 is a trademark, and Intel and Pentium are registered trademarks of Intel Corporation. PowerPC is a trademark of IBM Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-05291 Rev. *C Page 33 of 34 © Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. Cypress products are not warranted nor intended to be used for medical, life-support, life-saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. CY7C1360B CY7C1362B Document History Page Document Title: CY7C1360B/CY7C1362B 9-Mbit (256K x 36/512K x 18) Pipelined SRAM Document #: 38-05291 Rev. *C Issue Date Orig. of Change REV. ECN NO. Description of Change ** 114766 08/08/02 RCS New Data Sheet *A 117939 08/20/02 RCS Added A0 and A1 to 165 fBGA pinout *B 205060 See ECN NJY Final Data Sheet *C 225181 See ECN VBL Update Ordering Info section: shade S,E part numbers Document #: 38-05291 Rev. *C Page 34 of 34