Hittite HMC421QS16 Pcs/umts high ip3 rfic downconverter, 1.4 - 2.3 ghz Datasheet

HMC421QS16 / 421QS16E
v04.0810
MIXERS - DOWNCONVERTERS - SMT
9
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
Typical Applications
Features
The HMC421QS16 / HMC421QS16E is ideal for:
Input IP3: +19 dBm
• GSM, GPRS & EDGE Infrastructure
Integrated IF & LO Amps: +10 dBm LO
• CDMA, WCDMA Infrastructure
Conversion Gain: 9 dB
• PHS & PDC Infrastructure
Noise Figure: 9 dB
Single Positive Supply: +5V @ 60 mA
Functional Diagram
General Description
The HMC421QS16 & HMC421QS16E are high
linearity down-converter receiver ICs suitable for
PCS/UMTS infrastructure applications. The receiver
IC is designed to support UMTS applications where
a high third order intercept point (OIP3) is required.
A passive mixer coupled with a high dynamic range
IF amplifier achieves an Input IP3 of +19 dBm. The
converter provides a gain of 8 dB and 9 dB typical
single side band noise. The IC operates from positive
+5V rails and consumes 60 mA of current. The design
requires no external Baluns. The mixer supports IF
frequencies between 50 MHz and 300 MHz.
Electrical Specifications, TA = +25 °C, LO = +10 dBm, Vdd = 5V
Parameter
IF= 100 MHz
Min.
Typ.
IF= 250 MHz
Max.
Min.
Typ.
IF= 250 MHz
Max.
Min.
Typ.
Max.
Units
Frequency Range, RF
1.4 - 1.6
1.7 - 2.0
2.0 - 2.3
GHz
Frequency Range, LO
1.3 - 1.55
1.4 - 1.95
1.7 - 2.25
GHz
50 - 300
MHz
8
dB
Frequency Range, IF*
Conversion Gain
50 - 100
6
Noise Figure (SSB)
LO to RF Isolation
50 - 300
9
7
11
23
9
5
9
29
28
33
9.5
dB
26
32
dB
dB
LO to IF Isolation
35
42
42
52
50
60
RF to IF Isolation
35
42
42
52
50
60
dB
IP3 (Input)
15
18
17
19
17
20
dBm
1 dB Compression (Input)
3
6
4
6.5
4
7
dBm
+8 to +12
dBm
LO Input Drive Level (Typical)
Supply Current (Idd for LO & IF)
(IF bias resistor= 6.8 Ohms)
+8 to +12
84
+8 to +12
105
84
105
84
105
mA
* If matching must be tuned for optimal results, see application circuit herein.
9-1
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC421QS16 / 421QS16E
v04.0810
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
Isolation @ LO = +10 dBm
0
12
-15
10
8
6
+25 C
-40 C
+85 C
4
-30
-45
-60
RF/IF
LO/RF
LO/IF
-75
2
-90
0
1
1.5
2
1
2.5
1.5
0
12
-5
10
8
6
LO = +4 dBm
LO = +6 dBm
LO = +8 dBm
LO = +10 dBm
LO = +12 dBm
LO = +13 dBm
2
2.5
Return Loss @ LO = +10 dBm
14
RETURN LOSS (dB)
CONVERSION GAIN (dB)
Conversion Gain vs. LO Drive
4
2
FREQUENCY (GHz)
FREQUENCY (GHz)
-10
-15
-20
RF
LO
-25
-30
0
1
1.5
2
1
2.5
1.5
Conversion Gain
vs. Vdd @ LO = +10 dBm
14
12
10
RESPONSE (dB)
10
8
+4.5V
+5.0V
+5.5V
4
2.5
IF Bandwidth @ LO = +10 dBm
14
6
2
FREQUENCY (GHz)
FREQUENCY (GHz)
CONVERSION GAIN (dB)
9
MIXERS - DOWNCONVERTERS - SMT
14
ISOLATION (dB)
CONVERSION GAIN (dB)
Conversion Gain
vs. Temperature @ LO = +10 dBm
6
CONVERSION GAIN
RETURN LOSS
2
-2
-6
2
0
-10
1
1.5
2
FREQUENCY (GHz)
2.5
0
0.1
0.2
0.3
0.4
0.5
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
9-2
HMC421QS16 / 421QS16E
v04.0810
Input P1dB vs. Vdd @ LO = +10 dBm
10
10
8
8
INPUT P1dB (dBm)
INPUT P1dB (dBm)
Input P1dB vs.
Temperature @ LO = +10 dBm
6
4
+25 C
-40 C
+85 C
2
0
1.4
1.6
1.8
6
4
+4.5V
+5.0V
+5.5V
2
2
2.2
0
1.4
2.4
1.6
FREQUENCY (GHz)
2
2.2
2.4
Input and Output IP3 vs. LO Drive*
40
40
OIP3
OIP3
30
30
IP3 (dBm)
IIP3
20
OUTPUT, +25C
OUTPUT, -40C
OUTPUT, +85C
INPUT, +25C
INPUT, -40C
INPUT, +85C
10
0
1.4
1.8
FREQUENCY (GHz)
Input and Output IP3 vs.
Temperature @ LO = +10 dBm*
IP3 (dBm)
MIXERS - DOWNCONVERTERS - SMT
9
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
1.6
1.8
2
2.2
IIP3
20
OUTPUT, LO = +8dBm
OUTPUT, LO = +10dBm
OUTPUT, LO = +12dBm
INPUT, LO = +8dBm
INPUT, LO = +10dBm
INPUT, LO = +12dBm
10
0
1.4
2.4
1.6
FREQUENCY (GHz)
1.8
2
2.2
2.4
2.2
2.4
FREQUENCY (GHz)
Input and Output IP3
vs. Vdd @ LO = +10 dBm*
Input IP2 vs.
Temperature @ LO = +10 dBm*
40
80
OIP3
IIP3
20
OUTPUT, Vdd = +4.5V
OUTPUT, Vdd = +5.0V
OUTPUT, Vdd = 5.5V
INPUT, Vdd = +4.5v
INPUT, Vdd = +5.0V
INPUT, Vdd = 5.5V
10
0
1.4
+ 25 C
-40 C
+ 85 C
75
IP2 (dBm)
IP3 (dBm)
30
1.6
1.8
2
2.2
70
65
2.4
FREQUENCY (GHz)
60
1.4
1.6
1.8
2
FREQUENCY (GHz)
* Two-tone input power= -5 dBm each tone, 1 MHz spacing.
9-3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC421QS16 / 421QS16E
v04.0810
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
Noise Figure
Swept IF, Fixed LO = 2 GHz
15
+25 C
-40 C
+85 C
13
NOISE FIGURE (dB)
NOISE FIGURE (dB)
13
11
9
7
5
1.4
9
15
11
9
7
5
1.6
1.8
2
2.2
2.4
0
0.1
FREQUENCY (GHz)
0.2
0.3
0.4
FREQUENCY (GHz)
MxN Spurious @ IF Port
Harmonics of LO
nLO
nLO Spur @ RF Port
mRF
0
1
2
3
4
LO Freq. (GHz)
1
2
3
4
0
XX
42
55
47
52
1.4
27
16
33
33
1
65
0
66
80
89
1.6
30
19
33
42
2
>108
103
50
99
106
1.8
32
19
29
35
3
>108
>108
>108
80
>108
2
33
19
30
49
4
>108
>108
>108
>108
>108
2.2
33
20
34
45
2.4
28
20
34
42
RF = 2.05 GHz @ -10 dBm
LO = 1.8 GHz @ +10 dBm
All values in dBc relative to the IF power level.
LO = +10 dBm
All values in dBc below input LO level @ RF port.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
MIXERS - DOWNCONVERTERS - SMT
Noise Figure vs. Temperature,
Swept LO, Fixed IF = 250 MHz
9-4
HMC421QS16 / 421QS16E
v04.0810
MIXERS - DOWNCONVERTERS - SMT
9
Absolute Maximum Ratings
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
Typical Supply Current vs. Vdd
RF / IF Input (Vdd= +5V)
+13 dBm
Vdd (LO + IF) (Vdc)
(Idd) mA
LO Drive (Vdd= +5V)
+15 dBm
4.5
61
Vdd (LO or IF)
+7 Vdc
5.0
62
Channel Temperature
150°C
5.5
63
Continuous Pdiss (T = 85°C)
(Derate 6.34 mW/°C above 85 C)
0.41 W
Storage Temperature
-65 to +150°C
Operating Temperature
-40 to +85°C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC421QS16
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC421QS16E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
HMC421
XXXX
HMC421
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
9-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC421QS16 / 421QS16E
v04.0810
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
Pin Number
Function
Description
1, 7, 9, 14, 16
N/C
Not Connected
2
LO
This pin is AC coupled and matched to 50 Ohm
from 1.3 - 2.5 GHz.
3, 4, 11, 12, 13
GND
Pin must connect to RF ground.
5
Vdd LO
Power supply for the LO amplifier. One external RF
bypass capacitor (10,000 pF) is required.
6
Vdd IF
Bias voltage for IF amplifier. One external RF bypass
capacitor (10,000 pF) is required.
8
IF Bias
DC bias setting for IF amplifier.
10
IF
Output of IF and bias port for amplifier. A pull up
inductor (L1), output matching network (C5, C6, L2),
and 10,000 pF bypass capacitor (C4) are required.
15
RF
This pin is DC coupled and matched to 50 Ohm
from 1.7 - 2.5 GHz.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
9
MIXERS - DOWNCONVERTERS - SMT
Pin Descriptions
9-6
HMC421QS16 / 421QS16E
v04.0810
Evaluation PCB
MIXERS - DOWNCONVERTERS - SMT
9
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
List of Materials for Evaluation PCB 105087 [1]
Item
Description
J1 - J3
PCB Mount SMA RF Connector
J4 - J6
DC Pins
C1
1000 pF Chip Capacitor, 0603 Pkg.
C2, C3, C4
0.01 µF Chip Capacitor, 0603 Pkg.
C5
82 pF Chip Capacitor, 0402 Pkg.
C6
6 pF Chip Capacitor, 0603 Pkg.
L1
150 nH Chip Inductor, 0805 Pkg.
L2
27 nH Chip Inductor, 0805
R1
6.8 Ohm Resistor, 0603
U1
HMC421QS16 / HMC421QS16E Mixer
PCB [2]
104814 Evaluation Board, 1.100” x 1.100”
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads should be connected directly to the ground
plane similar to that shown. A sufficient number of
via holes should be used to connect the top and
bottom ground planes. The evaluation circuit board
shown is available from Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
9-7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC421QS16 / 421QS16E
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.4 - 2.3 GHz
Application Circuit
Notes:
1. Pin 5 and Pin 6 may be connected to a common Vdd supply.
2. Select C6 & L2 to optimize IF frequency. Values for IF = 250 MHz are shown.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
9
MIXERS - DOWNCONVERTERS - SMT
v04.0810
9-8
Similar pages