LCD Switches Programmable OLED Video Switch and Display IS Series DISTINCTIVE CHARACTERISTICS • • • • • • • • • Organic LED technology Range of 65,536 colors in 16 bit mode, 256 colors in 8 bit mode Full viewing angle of 180° Exceptional contrast and brightness: 50 times greater brightness than previous LCD products, four times more enhanced resolution High resolution provides sharp, clear images of very small characters Operated by commands and data supplied via SPI communications protocol Distinct, long travel of 4.5mm (same as KP01 Series) Dust tight construction Sophisticated housing based on black color Viewing area: 15.5mm x 11.6mm (horizontal x vertical) High reliability and long life of three million actuations minimum High resolution of 64RGB x 48 pixels Epoxy Sealed Straight PC Terminals Snap-in Standoff for Easy, Secure Mounting and Alignment Viewing area: 12.9mm x 9.9mm (horizontal x vertical) High resolution of 52RGB x 36 pixels Crimped terminals ensure secure PC mounting and prevent dislodging during wave soldering APPLICATIONS Actual Sizes The OLED SMARTSWITCH Series complements multiple applications, including: TM • Broadcast equipment • Image equipment • Education equipment • Vending machines • Audio equipment • POS • Automation control equipment [email protected] www.greatecs.com 1 LCD Switches Programmable OLED Video Switch and Display IS Series SMARTSWITCH PART NUMBER & DESCRIPTION Part Number Switch Description OLED Pixel Format ISC15ANP4 SPST Momentary ON Gold Contacts Straight PC Terminals Color OLED Display Module 65,536 Colors 64RGB x 48 Pixels Horizontal x Vertical SMARTSWITCH SPECFICATIONS Circuit SPST normally open Contact Position Leave actuator: 1 – 2 OFF Push actuator: 1 – 2 ON Electrical Capacity (Resistive Load) 100mA @ 12V DC Contact Resistance 200 milliohms maximum @ 20mV 10mA Insulation Resistance 100 megohms minimum @ 100V DC Dielectric Strength 125V AC for 1 minute minimum Mechanical Endurance 3,000,000 operations minimum Electrical Endurance 3,000,000 operations minimum Operating Force 2.0 ± 0.5 Newtons Total Travel 4.5mm (.177”) SMARTSWITCH OLED SPECFICATIONS Characteristics of Display Display Device Color OLED display module Display Mode Passive matrix Viewing Area 15.5mm x 11.6mm (horizontal x vertical) Pixel Format 64RGB x 48 pixels (horizontal x vertical) Pixel Size 0.21mm x 0.20mm (horizontal x vertical) Interface Serial (SPI) interface Number of Colors 65,536 Colors (16bit: R 5bit/G 6bit/B 5bit) or 256 Colors (8bit: R 2bit/G 3bit/B 3bit) Operating Temperature Range –20°C ~ +70°C (–4°F ~ +158°F) Storage Temperature Range –30°C ~ +80°C (–22°F ~ +176°F) Operating Life Time (Display) 15,000 hours (at 40% duty) Absolute Maximum Ratings Recommended Operating Conditions Items Symbols Supply Voltage for Logic/Interface V DD Supply Voltage for Drive Input Voltage Ratings Items DD 2.4V 2.8V 3.5V V CC 15.0V 16.0V 17.0V V IH 0.8 x V –– –– V IL –– V CC –0.3V to +19.0V Supply Voltage for Drive VI –0.3V to V Input High Level Voltage Input Low Level Voltage D D +0.3V CC Symbols Min Typical Max Items I CC1 –– 5.5mA 7.0mA Luminosity All-Pixels-On Mode *Logic/IF System Power Current I DD1 –– 0.16mA 0.2mA White Color Coordinate Sleep Mode **Drive System Power Current I CC2 –– 10μA Red Color Coordinate Sleep Mode **Logic/IF System Power Current I DD2 –– DD –– 0.2V x V DD Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F) = 16.0V) All-Pixels-On Mode *Drive System Power Current –– –– 10μA * All pixels shall be turned on with the maximum level gray scale ** All pixels shall be turned off (while chip is operating) [email protected] Maximum V DD = 2.8V, V Items Typical –0.3V to +4.0V Current Consumption (Temperature at 25°C, V Symbols Minimum Supply Voltage for Logic/Interface Green Color Coordinate Blue Color Coordinate Contrast Ratio (x) (y) (x) (y) (x) (y) (x) (y) Min Typical Max Unit Remarks 75 100 125 cd/m 2 White (All pixels on) 0.29 0.30 0.60 0.31 0.26 0.59 0.10 0.12 100 0.31 0.35 0.64 0.35 0.30 0.63 0.14 0.18 –– 0.35 0.40 0.68 0.39 0.34 0.67 0.18 0.24 –– –– –– –– –– –– –– –– –– –– www.greatecs.com 2 LCD Switches Programmable OLED Video Switch and Display IS Series SMARTSWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Color OLED Panel 64RGB x 48 SR1,SG1,SB1......SR64, SG64,SB64 COM1....COM48 Segment Driver Common Driver OLED Driver with Controller VDD 3 VCC 9 RES 5 SEG/COM Driving Block Gray Scale Decoder SCK 7 SS 4 SDI 8 D/C 6 Oscillator Graphic Display Data RAM 96 x 64 x 16 Bit Display Timing Generator Command Decoder MCU Interface ISC15ANP4 GND 10 SW 2 1 Pin No. Symbol SW Name Function 1 2 3 4 SW SW V DD SS Terminal of Switch Terminal of Switch Power Slave Select Normally open Normally open Power source for logic circuit Slave select for SPI. This line is active low. 5 RES Reset Reset signal input. When pin is low, initialization of chip is executed 6 D/C Data/Command 7 8 SCK SDI VCC GND Serial Clock Serial Data In Power Ground 9 10 Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. Clock line for SPI that synchronizes command and data Data input line for SPI Power source for drive OLED Connect to ground SMARTSWITCH TYPICAL DIMENSIONS Terminal numbers are not on the switch. See Pixel Detail (3.3) .130 (13.41) .528 (18.0) .709 Standoff 1 Standoff 2 (0.6) Typ .024 (20.59) .811 (11.6) .457 (9.57) .377 (0.02) Typ .0008 (0.21)Typ .0083 (0.02) Typ .0008 See Pixel Detail A [email protected] (16.0) .630 (0.4) Typ .016 See Standoff Detail (15.5) .610 (23.13) .911 Pixel Detail (23.0) .906 Pixel Detail A (0.20) .0079 (0.17) .0067 (0.04) Typ .0016 (0.07) Typ .0028 10 (7.62) .300 (0.74) .029 (0.20) Typ .0079 (1.0)Typ .039 2 (0.2) .008 R Standoff 1 (8.0) .315 (1.25) .049 (2.0) Dia .079 Dimension A Standoff 2 = (2.3) Standoff 1 = (2.7) .091 .106 (0.2) Typ .008 (2.0) .079 (7.05) .278 2x (0.9) Dia .035 (18.0) .709 Footprint A (7.0) .276 3 (0.3) Typ .012 R G B R (0.21) .0083 1 9 Standoff 2 (3.4) .134 Standoff Detail 4 (1.0)Typ .039 (7.0) .276 9 3 2 10 (7.62) .300 4 1 8x (0.75) Dia .029 (2.0) .079 (7.05) .278 (8.0) .315 (16.0) .630 4x (1.3) Dia .051 Landless www.greatecs.com 3 LCD Switches Programmable OLED Video Switch and Display IS Series SMARTSWITCH PART NUMBER & DESCRIPTION Part Number Display Description OLED Pixel Format ISC01P Straight PC Terminals Color OLED Display Module 65,536 Colors 52RGB x 36 Pixels Horizontal x Vertical SMARTSWITCH LCD SPECFICATIONS Characteristics of Display Display Device Color OLED display module Display Mode Passive matrix Viewing Area 12.9mm x 9.9mm (horizontal x vertical) Pixel Format 52RGB x 36 pixels (horizontal x vertical) Pixel Size 0.21mm x 0.22mm (horizontal x vertical) Interface Serial (SPI) interface Number of Colors 65,536 Colors (16bit: B 5bit/G 6bit/R 5bit) or 256 Colors (8bit: B 3bit/G 3bit/R 2bit) Operating Temperature Range –20°C ~ +70°C (–4°F ~ +158°F) Storage Temperature Range –30°C ~ +80°C (–22°F ~ +176°F) Operating Life Time (Display) 15,000 hours (40% pixels ON) Absolute Maximum Ratings Absolute Maximum Ratings Items Symbols Ratings Items Symbols Minimum Typical Maximum Supply Voltage for Logic/Interface V DD –0.3V to +4.0V Supply Voltage for Logic/Interface V DD 2.4V 2.8V 3.5V Supply Voltage for Drive V CC 0.3V to +19.0V Supply Voltage for Drive V CC 15.0V 16.0V 17.0V Input Voltage VI –0.3V to V Input High Level Voltage VIH 0.8 x V –– –– Input Low Level Voltage V IL –– DD +0.3V Current Consumption (Temperature at 25°C, V DD = 2.8V, V Items All-Pixels-On Mode *Drive System Power Current All-Pixels-On Mode *Logic/IF System Power Current Sleep Mode **Drive System Power Current Sleep Mode **Logic/IF System Power Current CC Max –– 4.5mA I DD1 I CC2 I DD2 3.5mA –– 0.16mA –– –– –– –– 0.2mA 10μA 10μA *All pixels shall be turned on with the maximum level gray scale **All pixels shall be turned off (while chip is operating) [email protected] –– 0.2V x V DD Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F) = 16.0V) Symbols Min Typical I CC1 DD Items Luminosity Min Typical Max Unit Remarks 75 100 125 cd/m 2 White (All pixels on) White Color Coordinate (x) 0.29 0.31 0.35 –– (y) 0.30 0.35 0.40 –– Red Color Coordinate (x) 0.60 0.64 0.68 –– (y) 0.31 0.35 0.39 –– Green Color Coordinate (x) 0.26 0.30 0.34 –– (y) 0.59 0.63 0.67 –– Blue Color Coordinate (x) 0.10 0.14 0.18 –– (y) 0.12 0.18 0.24 –– 100 –– –– –– Contrast Ratio www.greatecs.com 4 LCD Switches Programmable OLED Video Switch and Display IS Series SMARTSWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Color OLED Panel 52RGB x 36 SR1,SG1,SB1......SR52, SG52,SB52 COM1....COM36 Segment Driver Common Driver OLED Driver with Controller VDD 1 VCC 7 RES 3 SCK 5 SS 2 SDI 6 D/C 4 SEG/COM Driving Block Gray Scale Decoder Oscillator Graphic Display Data RAM 96 x 64 x 16 Bit Display Timing Generator Command Decoder MCU Interface ISC01P GND 8 Pin No. Symbol Name Function 1 V DD Power Power source for logic circuit 2 SS Slave Select Slave select for SPI. This line is active low. 3 RES Reset 4 D/C Data/Command Reset signal input. When pin is low, initialization of chip is executed Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. 5 SCK Serial Clock Clock line for SPI that synchronizes command and data 6 SDI Serial Data In Data input line for SPI 7 VCC Power Power source for drive OLED 8 GND Ground Connect to ground SMARTSWITCH TYPICAL DIMENSIONS Terminal numbers are not on the switch. See Pixel Detail (12.9) .508 (9.9) .390 (17.2) .677 See Standoff Detail (0.4) Typ .016 (7.89) .311 (16.8) .661 (10.0) .394 (0.65) Typ .026 (14.7) .579 (5.25) .207 (0.75) .030 (0.7) .028 (9.9) .390 (10.89) .429 (17.8) .701 Pixel Detail (0.22) Typ .0087 Pixel Detail A (0.21)Typ .0083 (0.02) Typ .0008 (0.22) .0087 (0.19) .0075 R R G B R (0.2) (2.0) .008 .079 (1.0) Typ .039 (3.0) .118 (7.0) .276 (15.0) .591 (0.02) Typ .0008 See Pixel Detail A Footprint (14.7) .579 (16.8) .661 8 [email protected] (1.0)Typ .039 (5.25) .207 2 1 4x (0.9) Dia .035 (0.21) .0083 (2.0) .079 (15.0) .591 (10.0) .394 7 (0.04) Typ .0016 (0.07) Typ .0028 (0.4) Typ .016 (7.0) .276 (2.0) .079 3x (0.9) Dia .035 Landless 8x (.075) Dia .029 www.greatecs.com 5 LCD Switches Programmable OLED Video Switch and Display IS Series TIMING SPECIFICATIONS FOR SMARTSWITCH & SMARTDISPLAY AC Characteristics (Temperature at 25°C) , V DD = 2.4V ~ 3.5V) Items Symbols Minimum Typical Maximum Clock Cycle Time tc yc le 150ns –– –– D/C Setup Time tAS 40ns –– –– D/C Hold Time tAH 40ns –– –– SS Setup Time tC SS 75ns –– –– D/C SS tAS tAH tCSS tCSH tR SS Hold Time tC SH 60ns –– –– Write Data Setup Time tDSW 40ns –– –– Write Data Hold Time tDHW 40ns –– –– SCK Low Time tC LKL 75ns –– –– SCK High Time tC LKH 75ns –– –– SCK Rise Time tR –– –– 15ns SCK Fall Time tF –– –– 15ns tC LKH tcy cle SCK tC LKL tF tD SW tD H W D7 SDI D6 D5 D4 D2 D3 D1 D0 STATE TRANSITION 7 : Initialization 1 : Power ON, 7 : Initialization State 0 Power OFF (VCC, VDD O F F) 2 : Power OFF State 1 Display OFF (Sleep Mode) 3 : Display ON 4 : Display OFF 8 : Changing the Display State Number State V CC VDD Changing the Display 0 Power OFF OFF –– OFF OFF Disable 1 Display OFF OFF ON ON ON Enable 2 Display ON ON OFF ON ON Enable Display Sleep Transition Initialization Setting State 0 Power ON 2 Power OFF 3 Display ON 4 Display OFF 7 Initialization Initialize Setting of Command/Data Image Rewriting Send Display Data Display Settings Dimmer, Scroll, etc. 8 [email protected] Power ON State 1 State 2 Power OFF State 0 Minimum 0µs Minimum 0µs 0V Reset low pulse width Trw (minimum 3µs) Index 1 8 : Changing the Display Power ON/OFF Sequence VDD State Transition State 2 Display ON RES “L” or “Hi-z” Refer to "Power ON/OFF Sequence" “L” or “Hi-z” Minimum 3µs Minimum 0µs VCC D/C SS “L” or “Hi-z” SCK SDI VDD level (due to ESD protection circuit between VDD and VCC ) “H” or “L” “L” or “Hi-z” www.greatecs.com 6 LCD Switches Programmable OLED Video Switch and Display IS Series PRECAUTIONS FOR HANDLING & STORAGE ATTENTION ELECTROST AT IC SENSITIVE DEVICES Handling 1. The IS Series OLED devices are electrostatic sensitive. To avoid damage to IC, do not touch keytops unless properly isolated from static electricity. 2. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages. 3. If the OLED panel is broken, avoid contact with the contents and wash off any spills to the skin or clothing. 4. Limit operating force to switch keytop to 100.0N maximum, as excessive pressure may damage the OLED. 5. For OLED display, it is necessary for terminal of metal cover to be connected to a ground. 6. Recommended soldering time and temperature limits for OLED switch or display: 11 seconds maximum @ 270°C maximum; avoid temperatures exceeding 80°C at the OLED. 7. The IS series OLED devices are not process sealed. 8. If OLED unit is operated with the same display pattern, the difference between the operation duration of adjacent pixels may be interpreted as difference between luminosity of pixels. To minimize this difference, operate OLED unit so that each pixel may be turned on at frequency as equal as possible. 9. For switch, clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. For display, avoid contact with any flux or detergent. If any liquids spill on display surface, immediately wipe with soft absorbent cloth. Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. [email protected] www.greatecs.com 7