HA-2529/883 Uncompensated, High Slew Rate High Output Current, Operational Amplifier July 1997 Features Description • This Circuit is Processed in Accordance to MIL-STD-883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. The HA-2529/883 is a monolithic operational amplifier which typifies excellence of design. With a design based on years of experience coupled with the reliable dielectric isolation process, these amplifiers provide an outstanding combination of DC and AC parameters at closed loop gains of 3 or greater without external compensation. • High Slew Rate . . . . . . . . . . . . . . . . . . . . . 135V/µs (Min) 150V/µs (Typ) • High Output Current . . . . . . . . . . . . . . . . . ±30mA (Min) The HA-2529/883 offers 135V/µs (min) slew rate and fast settling time (200ns typ), while consuming a mere 6mA (max) quiescent supply current, making these amplifiers ideal components for video circuitry and data acquisition designs. With 15MHz minimum gain-bandwidth product combined with 7.5kV/V minimum open loop gain, the HA-2529/883 is an ideal component for demanding signal conditioning designs. These devices provide ±30mA (min) output current drive with an output voltage swing of ±10V (min), making then suited for pulse amplifier and RF amplifier components. HA-2529/883 will upgrade a system presently using the HA-2520/22/883 or EHA-2520/22/883 in regards to output current, slew rate, offset voltage drift, and offset current drift. To insure compliance with slew rate and transient response specifications, all devices are 100% tested for AC performance characteristics over full temperature. • High Gain-Bandwidth Product . . . . . . . . . 15MHz (Min) 20MHz(Typ) • Wide Power Bandwidth . . . . . . . . . . . . . . . 2.1MHz (Min) • High Input Impedance . . . . . . . . . . . . . . . . . 50MΩ (Min) 130MΩ (Typ) • Low Offset Current . . . . . . . . . . . . . . . . . . . 25nA (Max) 5nA (Typ) • Fast Settling (10V Step to 0.1%) . . . . . . . . . . . 200ns (Typ) • Low Quiescent Supply Current . . . . . . . . . . 6mA (Max) Applications • Data Acquisition Systems Ordering Information • RF Amplifiers • Video Amplifiers PART NUMBER • Signal Generators • Pulse Amplification TEMP. RANGE (oC) PACKAGE PKG. NO. HA2-2529/883 -55 to 125 8 Pin Metal Can T8.C HA7-2529/883 -55 to 125 8 Ld CERDIP F8.3A Pinouts HA-2529/883 (CERDIP) TOP VIEW HA-2529/883 (METAL CAN) TOP VIEW COMP BAL 1 -IN 2 +IN 3 V- 4 8 + COMP 7 V+ 6 OUT 5 BAL 8 BAL + 2 -IN +IN 7 V+ 1 6 OUT 5 3 BAL 4 V- CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 1 511025-883 File Number 3736.1 Spec Number HA-2529/883 Absolute Maximum Ratings TA = 25oC Thermal Information Thermal Resistance (Typical, Note 1) θJA θJC CERDIP Package . . . . . . . . . . . . . . . . 115oC/W 28oC/W Metal Can Package . . . . . . . . . . . . . . . 160oC/W 75oC/W Package Power Dissipation Limit at 75oC for TJ ≤ 175oC CERDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625mW Package Power Dissipation Derating Factor Above 75oC CERDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mW/oC Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 175oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V VINCM ≤ 1/2 (V+ - V-) RL ≥ 500Ω CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETER Input Offset Voltage Input Bias Current SYMBOL VIO +IB -IB Input Offset Current Common Mode Range IIO +CMR -CMR Large Signal Voltage Gain +AVOL -AVOL Common Mode Rejection Ratio +CMRR -CMRR Output Voltage Swing +VOUT -VOUT CONDITIONS VCM = 0V VCM = 0V, +RS = 100kΩ, -RS = 100Ω VCM = 0V, +RS = 100Ω, -RS = 100kΩ VCM = 0V, +RS = 100kΩ, -RS = 100kΩ V+ = 5V, V- = -25V V+ = 25V, V- = -5V VOUT = 0V and +10V, RL = 2kΩ VOUT = 0V and -10V, RL = 2kΩ ∆VCM = +10V, V+ = +5V, V- = -25V, VOUT = -10V ∆VCM = -10V, V+ = +25V, V- = -5V, VOUT = +10V RL = 2kΩ RL = 2kΩ GROUP A SUBGROUPS TEMP. (oC) MIN MAX UNITS 1 25 -5 5 mV 2, 3 125, -55 -8 8 mV 1 25 -200 200 nA 2, 3 125, -55 -400 400 nA 1 25 -200 200 nA 2, 3 125, -55 -400 400 nA 1 25 -25 25 nA 2, 3 125, -55 -50 50 nA 1 25 +10 - V 2, 3 125, -55 +10 - V 1 25 - -10 V 2, 3 125, -55 - -10 V 4 25 10 - kV/V 5, 6 125, -55 7.5 - kV/V 4 25 10 - kV/V 5, 6 125, -55 7.5 - kV/V 1 25 83 - dB 2, 3 125, -55 80 - dB 1 25 83 - dB 2, 3 125, -55 80 - dB 4 25 10 - V 5, 6 125, -55 10 - V 4 25 - -10 V 5, 6 125, -55 - -10 V Spec Number 2 511025-883 HA-2529/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETER Output Current SYMBOL +IOUT -IOUT Quiescent Power Supply Current +ICC -ICC Power Supply Rejection Ratio +PSRR -PSRR Offset Voltage Adjustment +VIOAdj -VIOAdj CONDITIONS GROUP A SUBGROUPS TEMP. (oC) MIN MAX UNITS 4 25 30 - mA 5, 6 125, -55 20 - mA 4 25 - -30 mA 5, 6 125, -55 - -20 mA 1 25 - 6 mA 2, 3 125, -55 - 7 mA 1 25 -6 - mA 2, 3 125, -55 -7 - mA 1 25 80 - dB 2, 3 125, -55 80 - dB 1 25 80 - dB 2, 3 125, -55 80 - dB 1 25 VIO-1 - mV 2, 3 125, -55 VIO-1 - mV 1 25 VIO+1 - mV 2, 3 125, -55 VIO+1 - mV VOUT = -10V VOUT = +10V VOUT = 0V, IOUT = 0mA VOUT = 0V, IOUT = 0mA ∆VSUP = 10V, V+ = +20V, V- = -15V, V+ = +10V, V- = -15V ∆VSUP = 10V, V+ = +15V, V- = -20V, V+ = +15V, V- = -10V Note 2 Note 2 NOTE: 2. Offset adjustment range is [VIO (Measured) ±1mV] minimum referred to output. This test is for functionality only to assure adjustment through 0V. TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +3V/V, Unless Otherwise Specified. PARAMETERS Slew Rate SYMBOL +SR -SR Rise and Fall Time tr tf Overshoot +OS -OS CONDITIONS GROUP A SUBGROUPS TEMP. (oC) MIN MAX UNITS 7 25 135 - V/µs 8A, 8B 125, -55 125 - V/µs 7 25 135 - V/µs 8A, 8B 125, -55 125 - V/µs 7 25 - 45 ns 8A, 8B 125, -55 - 50 ns 7 25 - 45 ns 8A, 8B 125, -55 - 50 ns 7 25 - 40 % 8A, 8B 125, -55 - 40 % 7 25 - 40 % 8A, 8B 125, -55 - 40 % VOUT = -5V to +5V 25% ≤ +SR ≤ 75% VOUT = +5V to -5V 75% ≥ -SR ≥ 25% VOUT = 0 to +200mV 10% ≤ tr ≤ 90% VOUT = 0 to -200mV 10% ≤ tf ≤ 90% VOUT = 0 to +200mV VOUT = 0 to -200mV Spec Number 3 511025-883 HA-2529/883 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, CCOMP = 0pF, Unless Otherwise Specified. PARAMETERS SYMBOL Differential Input Resistance RIN NOTES TEMP. (oC) MIN MAX UNITS VCM = 0V 3 25 50 - MΩ 3 25 15 - MHz 3, 4 25 2.1 - MHz CONDITIONS Gain Power Bandwidth GBWP VO = 200mV, fO ≥ 10kHz Full Power Bandwidth FPBW VPEAK = 10V Minimum Closed Loop Stable Gain CLSG RL = 2kΩ, CL = 50pF 3 -55 to 125 ±3 - V/V Output Resistance ROUT Open Loop 3 25 - 60 Ω 3, 5 -55 to 125 - 210 mW Power Consumption PC VOUT = 0V, IOUT = 0mA NOTES: 3. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 4. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK). 5. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.) TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLES 1 AND 2) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 6), 2, 3, 4, 5, 6, 7, 8A, 8B Group A Test Requirements 1, 2, 3, 4, 5, 6, 7, 8A, 8B Groups C and D Endpoints 1 NOTE: 6. PDA applies to Subgroup 1 only. Spec Number 4 511025-883 HA-2529/883 Die Characteristics DIE DIMENSIONS: WORST CASE CURRENT DENSITY: 0.78 x 105 A/cm2 67 mils x 57 mils x 19 mils 1700µm x 1440µm x 483µm SUBSTRATE POTENTIAL (Powered Up): METALLIZATION: Unbiased Type: Al, 1% Cu Thickness: 16kÅ ±2kÅ TRANSISTOR COUNT: 40 PROCESS: Bipolar Dielectric Isolation GLASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.) Silox Thickness: 12kÅ ± 2kÅ Nitride Thickness: 3.5kÅ ± 1.5kÅ Metallization Mask Layout HA-2529/883 COMP V+ OUT BAL -IN +IN BAL V- Spec Number 5 511025-883 HA-2529/883 Test Circuit (Applies to Tables 1 and 2) 667 1.33K ACOUT 0.1 100K S7 3 S3A S1 2 1 - 1 OPEN 2 S2 1 S5A S6 1 OPEN 2 100K 2 100 50K OPEN 1 NOTE: Includes stray capacitances 2 1 S5B + 2 For loop stability, use min value capacitor to prevent oscillation 500K 2 DUT OPEN 1 - S8 2 3 OPEN 1 - + S9 + -1 2 S3B BUFFER V2 2K 1 OPEN 100 V1 1 1 OPEN 2 -1/10 50pF (NOTE) V+ 0.1 VAC 1 50 10K VEOUT x2 5K 2 S4 ALL RESISTORS = ±1% (Ω) ALL CAPACITORS = ±10% (µF) 1 50K Test Circuits and Waveforms +1.67V INPUT -67mV 0mV 90% OUTPUT -5V 0 67mV INPUT -1.67V +5V OVERSHOOT ∆V 10% ∆t SLEW RATE = ∆V/∆t +200mV 90% OUTPUT 10% 0V ERROR BAND ±10mV FROM FINAL VALUE SETTLING TIME RISE TIME NOTE: Measured on both positive and negative transitions from 0V to +200mV and 0V to -200mV at the output. FIGURE 1. SLEW RATE AND SETTLING TIME VIN FIGURE 2. TRANSIENT RESPONSE + - VOUT 1.33kΩ 50Ω 50pF 667Ω FIGURE 3. SIMPLIFIED TEST CIRCUIT (APPLIES TO TABLE 2) Spec Number 6 511025-883 Burn-In Circuits HA7-2529/883 CERDIP 1 R1 8 2 - 3 + D2 C3 6 4 V- V+ 7 D1 C1 5 C2 HA2-2529/883 METAL CAN V+ C3 C1 8 1 7 + 2 6 5 3 4 R1 V- NOTES: R1 = 1MΩ, ±5%, 1/4W (Min) C1 = C2 = 0.01µF/Socket (Min) or 0.1µF/Row (Min) C3 = 0.01µF/Socket (10%) D1 = D2 = 1N4002 or Equivalent/Board |(V+) - (V-)| = 30V 7 C2 D2 D1 HA-2529/883 Ceramic Dual-In-Line Frit Seal Packages (CERDIP) c1 F8.3A MIL-STD-1835 GDIP1-T8 (D-4, CONFIGURATION A) LEAD FINISH 8 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE -D- -A- BASE METAL INCHES (c) E b1 M M (b) -Bbbb S C A-B S SECTION A-A D S D BASE PLANE Q -C- SEATING PLANE A α L S1 eA A A b2 b ccc M C A-B S e D S eA/2 c aaa M C A - B S D S SYMBOL MIN MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.405 - 10.29 5 E 0.220 0.310 5.59 7.87 5 e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - 3.81 BSC - eA/2 NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. MILLIMETERS 0.150 BSC L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 6 S1 0.005 - 0.13 - 7 α 90o 105o 90o 105o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2, 3 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. N 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 8 8 8 Rev. 0 4/94 5. This dimension allows for off-center lid, meniscus, and glass overrun. 6. Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners. 8. N is the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. Spec Number 8 511025-883 HA-2529/883 Metal Can Packages (Can) T8.C MIL-STD-1835 MACY1-X8 (A1) REFERENCE PLANE A 8 LEAD METAL CAN PACKAGE e1 L L2 L1 INCHES ØD2 A A k1 Øe ØD ØD1 2 N 1 F α β Øb1 Øb k C L BASE AND SEATING PLANE Q BASE METAL Øb1 LEAD FINISH Øb2 SECTION A-A NOTES: 1. (All leads) Øb applies between L1 and L2. Øb1 applies between L2 and 0.500 from the reference plane. Diameter is uncontrolled in L1 and beyond 0.500 from the reference plane. MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.165 0.185 4.19 4.70 - Øb 0.016 0.019 0.41 0.48 1 Øb1 0.016 0.021 0.41 0.53 1 Øb2 0.016 0.024 0.41 0.61 - ØD 0.335 0.375 8.51 9.40 - ØD1 0.305 0.335 7.75 8.51 - ØD2 0.110 0.160 2.79 4.06 - e 0.200 BSC 5.08 BSC - e1 0.100 BSC 2.54 BSC - F - 0.040 - 1.02 - k 0.027 0.034 0.69 0.86 - k1 0.027 0.045 0.69 1.14 2 L 0.500 0.750 12.70 19.05 1 L1 - 0.050 - 1.27 1 L2 0.250 - 6.35 - 1 Q 0.010 0.045 0.25 1.14 - α 45o BSC 45o BSC β 45o BSC 45o BSC 3 N 8 8 4 2. Measured from maximum diameter of the product. 3 Rev. 0 5/18/94 3. α is the basic spacing from the centerline of the tab to terminal 1 and β is the basic spacing of each lead or lead position (N -1 places) from α, looking at the bottom of the package. 4. N is the maximum number of terminal positions. 5. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 6. Controlling dimension: INCH. All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 Spec Number 9 511025-883