IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES 0.5 AMP NEGATIVE VOLTAGE REGULATOR ! 2 1 3 FEATURES Pin 1 – Ground Pin 2 – VOUT Case – VIN Pin 1 – Ground Pin 2 – VIN Case – VOUT H Package – TO–39 SMD Package - SMD1 CERAMIC SURFACE MOUNT • OUTPUT CURRENT UP TO 0.5A • OUTPUT VOLTAGES OF -5, -12, -15V • 0.01% / V LINE REGULATION • 0.3% / A LOAD REGULATION GND 1 8 NC • THERMAL OVERLOAD PROTECTION NC 2 7 NC • SHORT CIRCUIT PROTECTION NC 3 6 VIN • OUTPUT TRANSISTOR SOA PROTECTION VOUT 4 5 NC • 1% VOLTAGE TOLERANCE (–A VERSIONS) 8 Pin J Package Order Information Part H–Pack Number (TO–39) IP79MxxAzz ✔ IP79Mxxzz ✔ IP120MAzz–xx ✔ IP120Mzz–xx ✔ Note: xx = Voltage Code (05, 12, 15) eg. IP79M05J DESCRIPTION J–Pack SMD–Pack Temp. CERDIP SMD1 Range ✔ ✔ -55 to +150°C ✔ ✔ ” ✔ ” ✔ ” zz = Package Code (H, J) IP120MAH–12 The IP120MA and IP79M00A series of voltage regulators are fixed output regulators intended for local, on-card voltage regulation. These devices are available in -5, -12, and -15 volt options and are capable of delivering in excess of 500mA over temperature. The A suffix devices are fully specified at 0.5A, provide 0.01% / V line regulation, 0.3% / A load regulation, and ±1% output voltage tolerance at room temperature. Protection features include safe operating area, current limiting and thermal shutdown. ABSOLUTE MAXIMUM RATINGS (TC = 25°C unless otherwise stated) VI DC Input Voltage PD Power Dissipation RqJC Thermal Resistance Junction to Case RqJA (for VO = -5, -12, -15V) Thermal Resistance Junction to Ambient -35V Internally limited – H Package 20°C / W – SMD Package TBA°C / W – H Package 120°C / W – J Package 119°C / W TJ Operating Junction Temperature Range –55 to 150°C Tstg Storage Temperature –65 to 150°C Note 1. Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 2W for the H–Package ,1.05W for the J–Package and 15W for the SG–Package. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Prelim. 9/00 IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES ELECTRICAL CHARACTERISTICS Parameter Test Conditions IO = 100mA VO Output Voltage VIN = -10V IP79M05A IP120MA–05 Min. Typ. Max. IP79M05 IP120M–05 Min. Typ. Max. -4.95 -5.05 -4.8 -5.15 -4.75 PD £ PMAX -4.85 IO = 350mA VIN = -8V to -18V TJ = -55 to 150°C DVO Load Regulation IQ Quiescent Current IO = 5mA to 500mA VIN = -10V VIN = -10V TJ = -55 to 150°C IO = 350mA TJ = -55 to 150°C IO = 5mA to 500mA DIQ Quiescent Current VIN = -10V IO = 200mA Change TJ = -55 to 150°C Output Noise Voltage DVIN DVO Ripple Rejection Dropout Voltage Isc Short Circuit Current Ipk Peak Output Current Average Temperature Coefficient of VO f = 10Hz to 100kHz f = 120Hz VIN = -8V to -18V IO = 300mA IO = 100mA TJ = -55 to 150°C 10 50 3 10 30 5 50 100 mV 1 2 2 mA 0.1 0.4 0.4 0.1 0.4 0.4 40 400 400 1 65 80 54 65 80 54 1.1 2.3 VIN = -35V 300 600 1.0 1.4 0.5 2.0 IO = 5mA V 3 IO = 350mA VIN = -10V -5.25 mV mA VIN = -8V to -25V TJ = -55 to 150°C VN -5.2 TJ = -55 to 150°C VIN = -7V to -25V Line Regulation -5 IO = 5mA to 350mA VIN = -7V to -25V DVO -5 Units 0.5 0.5 mV dB 2.3 V 300 600 mA 1.0 1.6 A 0.5 mV °C 1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. £ 10ms, d £ 5%). Output 2) Test Conditions unless otherwise stated: TJ = 25°C PMAX = 2W for H Package (TO–39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SMD1 Package (SMD1) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Prelim. 9/00 IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES ELECTRICAL CHARACTERISTICS Parameter Test Conditions IO = 100mA VO IP79M12A IP120MA–12 Min. Typ. Max. Output Voltage VIN = -19V -11.88 VIN = -14.5V to -30V -11.64 -12 IP79M12 IP120M–12 Min. Typ. Max. -12.12 -11.5 -12.36 -11.4 -12 -12.5 IO = 5mA to 350mA PD £ PMAX Units -12.6 V TJ = -55 to 150°C 4 18 80 4 18 50 10 60 240 mV 1.5 3 3 mA 0.1 0.4 0.4 0.1 0.4 0.4 96 960 960 VIN = -14.5V to -30V DVO Line Regulation IO = 350mA VIN = -15V to -25V TJ = -55 to 150°C DVO Load Regulation IQ Quiescent Current IO = 5mA to 500mA VIN = -19V VIN = -19V TJ = -55 to 150°C IO = 350mA TJ = -55 to 150°C IO = 5mA to 500mA DIQ Quiescent Current VIN = -19V IO = 200mA Change TJ = -55 to 150°C mA VIN = -14.5V to -30V TJ = -55 to 150°C VN Output Noise Voltage DVIN DVO Ripple Rejection Dropout Voltage Isc Short Circuit Current Ipk Peak Output Current Average Temperature Coefficient of VO f = 10Hz to 100kHz f = 120Hz IO = 300mA VIN = -15V to IO = 100mA -25V TJ = -55 to 150°C 58 72 54 58 72 54 IO = 350mA 1.1 2.3 VIN = -35V 300 600 1.0 1.4 1.2 4.8 VIN = -19V IO = 5mA 1.5 mV 0.5 0.5 mV dB 2.3 V 300 600 mA 1.0 1.6 A 1.2 mV °C 1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. £ 10ms, d £ 5%). Output 2) Test Conditions unless otherwise stated: TJ = 25°C PMAX = 2W for H Package (TO–39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SMD Package (SMD1) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Prelim. 9/00 IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES ELECTRICAL CHARACTERISTICS Parameter Test Conditions IO = 100mA VO IP79M15A IP120MA–15 Min. Typ. Max. Output Voltage VIN = -23V -14.85 VIN = -17.5V to -30V -14.55 -15 IP79M15 IP120M–15 Min. Typ. Max. -15.15 -14.4 -15.45 -14.25 -15 -15.6 IO = 5mA to 350mA PD £ PMAX Units -15.75 V TJ = -55 to 150°C 4 22 80 4 22 50 12 75 240 mV 1.5 3 3 mA 0.1 0.4 0.4 0.1 0.4 0.4 120 1200 1200 VIN = -17.5V to -30V DVO Line Regulation IO = 350mA VIN = -18V to -28V TJ = -55 to 150°C DVO Load Regulation IQ Quiescent Current IO = 5mA to 500mA VIN = -23V VIN = -23V TJ = -55 to 150°C IO = 350mA TJ = -55 to 150°C IO = 5mA to 500mA DIQ Quiescent Current VIN = -23V IO = 200mA Change TJ = -55 to 150°C mA VIN = -17.5V to -30V TJ = -55 to 150°C VN Output Noise Voltage DVIN DVO Ripple Rejection Dropout Voltage Isc Short Circuit Current Ipk Peak Output Current Average Temperature Coefficient of VO f = 10Hz to 100kHz f = 120Hz IO = 300mA VIN = -18.5V to IO = 100mA -28.5V TJ = -55 to 150°C 57 70 54 57 70 54 IO = 350mA 1.1 2.3 VIN = -35V 300 600 1.0 1.4 1.5 6.0 VIN = -23V IO = 5mA 1.5 mV 0.5 0.5 mV dB 2.3 V 300 600 mA 1.0 1.6 A 1.5 mV °C 1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. £ 10ms, d £ 5%). Output 2) Test Conditions unless otherwise stated: TJ = 25°C PMAX = 2W for H Package (TO–39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SMD Package (SMD1) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Prelim. 9/00