ACE510 Technology Dual, Low noise, 150mA LDO regulator Description The ACE510 dual, low-noise, low-dropout regulator delivers at least 150mA of continuous output current. The output voltage for each regulator is set independently by trimming. Voltages are selectable in 100mV steps within a range of 1.2V to 5.0V.Typical output noise is 27uVrms,and PSRR is 65dB at 1KHz. The ACE510 includes two independent logic-controlled shutdown inputs and allows the output of each regulator to be turned of independenly. The ACE510 includes high accuracy voltage reference, error amplifier, current limit circuit and output driver module. The ACE510 has excellent load and line transient response and good temperature characteristics, which can assure the stability of chip and power system. And it uses trimming technique to guarantee output voltage accuracy within±2%. The ACE510 is available in SOT-23-6 package which is lead (Pb)- free Features • • • • • • • • • • • • Two low dropout voltage regulators 150mA output current for each LDO 25uA operating supply current per LDO Low 27uVRMS output noiseV~10V Standby Mode: 0.1uA Low 200mV dropout at 100mA load 65dB PSRR at kHz Excellent Line regulation: 0.05%/V Independent Shutdown controls 1.2V to 5.0V Factory-Preset Output Output Current Limit Highly Accurate: ±2% (±1% customized) Application • • • • • • Cellular phones Cordless phones and radio communication equipment Battery Powered equipment Notebook and hand-ole equipment Wireless LAN GPS receivers Typical Performance Characteristic: ACE505-1.8V Output Output Current Iout (mA) VER 1.2 1 ACE510 Technology Dual, Low noise, 150mA LDO regulator Absolute Maximum Ratings Parameter Symbol Max Unit Input voltage VIN 10 V Power Dissipation SOT-23-6 Junction temperature Storage temperature Output Current 200 TJ TS 125 - 45 to 150 200 mW O C C mA O Packaging Type SOT-23-6 6 5 4 1 2 3 Pin SOT-23-6(C) SOT-23-6(D) SOT-23-6(E) Function Vout1 1 6 6 Output 1 pin Vdd 2 2 5 Input pin Vout2 3 4 1 Output 2 pin CE2 4 3 3 Chip Enable pin2 GND 5 5 2 Ground pin CE1 6 1 4 Chip Enable pin1 VER 1.2 2 ACE510 Technology Dual, Low noise, 150mA LDO regulator Ordering information Selection Guide ACE510 XX XX + H Halogen - free Pb - free CGM : SPT-23-6C DGM : SOT-23-6D EGM : SOT-23-6E Output Voltage： A:1.5V(Output1),2.5V(Output2) C:1.5V(Output1),3.0V(Output2) E:1.5V(Output1),4.0V(Output2) G:1.8V(Output1),2.5V(Output2) I: 1.8V(Output1),3.0V(Output2) K: 2.5V(Output1),1.8V(Output2) M:2.8V(Output1),1.8V(Output2) O:2.8V(Output1),2.8V(Output2) Q:3.0V(Output1),2.5V(Output2) S:3.0V(Output1),3.3V(Output2) U:3.3V(Output1),2.5V(Output2) W:5.0V(Output1),3.3V(Output2) Y:2.8V(Output1),3.3V(Output2) B:1.5V(Output1),2.8V(Output2) D:1.5V(Output1),3.3V(Output2) F:1.8V(Output1),1.8V(Output2) H:1.8V(Output1),2.8V(Output2) J:1.8V(Output1),3.3V(Output2) L:2.5V(Output1),2.5V(Output2) N:2.8V(Output1),2.5V(Output2) P:2.8V(Output1),3.0V(Output2) R:3.0V(Output1),3.0V(Output2) T:3.3V(Output1),1.8V(Output2) V:3.3V(Output1),2.8V(Output2) X:2.8V(Output1),1.5V(Output2) Z:3.3V(Output1),3.3V(Output2) VER 1.2 3 ACE510 Technology Dual, Low noise, 150mA LDO regulator Block Diagram Recommended Work Conditions Item Input Voltage Range Ambient Temperature Min Recommended Max Unit 8 V -40 85 ℃ Electrical Characteristics (Test Conditions: C1=1uF, C2=C3=2.2uF,TA=25℃, unless otherwise specified.) ACE510, fro arbitrary output voltage Parameter Symbol Input Voltage VIN Output Voltage VOUT Maximum Output Current Input-Output Voltage Differential IOUT(Max.) Dropout Voltage ΔVOUT / ΔVIN•VOUT Line Regulation Load Regulation ΔVOUT / ΔIOUT Supply Current Supply Current (Srandby) Iss Istandby Conditions Min Typ Max Units 1.8 8 V Vout Vin=Set Vout+1V Vout V x1.02 1mA≦Iout≦30mA x0.98 Vin-Vout=1V 150 mA Refer to the Electrical Characteristics by Output Voltage Iout=40mA 0.05 0.2 %/V 1.6V≦Vin≦8V Vin=Set Vout+1V 12 40 mA 1mA≦Iout≦80mA Vin=Set Vout+1V 25 50 uA Vin=Set Vout+1V 0.2 1.0 uA VER 1.2 4 ACE510 Technology Dual, Low noise, 150mA LDO regulator Vce=Gnd Output Voltage Temperature Coefficiency ΔVOUT / ΔT•VOUT Ripple Rejection PSRR Short Current Limit CE Pull down Resistance CE Input Voltage “H” CE Input Voltage “L” Output Noise Llim Rpd Vceh Vcel en Iout=30mA F=1kHz Ripple=0.5Vp-p Vin=Set Vout+1V Vout=0V 2.0 1.5 0 BW=10Hz~100kHz ±100 ppm/℃ 65 dB 20 5.0 mA MΩ V V uVrms 27 10.0 Vin 0.25 Electrical Characteristics by Output Voltage Output Voltge Vout(V) Vout=1.5V Vout=1.6V Vout=1.7V 1.8≦Vout≦2.0 2.1≦Vout≦2.7 2.8≦Vout≦4.0 Dropout Voltage, VDIF(V) Condition Typ Max 0.38 0.70 0.36 0.65 0.34 0.60 Iout=120mA 0.32 0.55 0.28 0.50 0.22 0.35 Typical Application Circuit Out2 C3 VOUT2 CE2 ACE510 Vin GND VDD VOUT1 CE1 Out1 C2 C1 Application hints: Note 1:Input capacitor (Cin=1uF) is recommended in all application circuit. Note 2:Output capacitor (C2=C3=1uF/2.2uF) is recommended in all application to assure the stability of circuit. VER 1.2 5 ACE510 Technology Dual, Low noise, 150mA LDO regulator Explanation： The ACE510 series are highly accurate ,Dual, low noise, CMOS low dropout voltage regulators. The output voltage for each regulator is set independently by trimming. Voltages are selectable in 100mV steps within a range of 1.2V to 5.0V . It also can be customized on command. The ACE510 includes high accuracy voltage reference, error amplifier, current limit circuit and output driver module. The ACE510 has excellent load and line transient response and good temperature characteristics, which can assure the stability of chip and power system. And it uses trimming technique to guarantee output voltage accuracy within±2% Typical Performance Characteristics 1.Output Voltage vs. Output Current (with output short protection) ACE510-1.8V 2.Output Voltage vs. Input Voltage ACE510-1.8V Output Current Iout(mA) 3.Dropout Voltage vs. Output Current Output Current Iout(mA) Input Voltage Vin(V) 4.Supply Current vs. Input Voltage Input Voltage Vin(V) VER 1.2 6 ACE510 Technology 5.Ripple rejection vs. Frequency Dual, Low noise, 150mA LDO regulator 6.Line transient response Voltage Frequency f(kHz) 7.Load transient response VER 1.2 7 ACE510 Technology Dual, Low noise, 150mA LDO regulator Packing Information SOT-23-6 VER 1.2 8 ACE510 Technology Dual, Low noise, 150mA LDO regulator Notes ACE does not assume any responsibility for use as critical components in life support devices or systems without the express written approval of the president and general counsel of ACE Electronics Co., LTD. As sued herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and shoes failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ACE Technology Co., LTD. http://www.ace-ele.com/ VER 1.2 9