Maxim MAX9670CTL+ Low-power audio/video switch with audio volume control for dual scart connector Datasheet

19-4653; Rev 0; 7/09
KIT
ATION
EVALU
E
L
B
AVAILA
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
The MAX9670/MAX9671 dual SCART matrices route
audio and video signals between a set-top box
decoder chip and two external SCART connectors
under I2C control. Operating from a 3.3V supply and a
12V supply, the MAX9670/MAX9671 consume 70mW
during quiescent operation and 471mW during average
operation when driving typical signals into typical
loads. Video input detection, video load detection, and
a 2.5mW standby mode facilitate the design of intelligent, low-power set-top boxes.
The MAX9670/MAX9671 audio section contains a
buffered crosspoint to route audio inputs to audio outputs and programmable volume control from -62dB to
0dB in 2dB steps. The DirectDrive® output amplifiers
create a 2VRMS full-scale audio signal biased around
ground, eliminating the need for bulky output capacitors and reducing click-and-pop noise. The zero-cross
detection circuitry also further reduces clicks and pops
by enabling audio sources to switch only during a zerocrossing. The MAX9671 offers TV left and right audio
inputs.
The MAX9670/MAX9671 video section contains a
buffered crosspoint to route video inputs to video outputs. The standard-definition video signals from the settop box decoder chip are lowpass filtered to remove
out-of-band artifacts.
The MAX9670/MAX9671 also support slow-switching
and fast-switching signals. An interrupt signal from the
MAX9670/MAX9671 informs the microcontroller when
the system status has changed.
Applications
Features
o 70mW Quiescent Power Consumption
o 2.5mW Standby Mode Consumption
o Programmable Audio Gain Control of -62dB to
0dB (TV Audio Outputs)
o Clickless, Popless, DirectDrive Audio
o Video Input and Video Load Detection
o Video Reconstruction Filter with 10MHz Passband
and 52dB Attenuation at 27MHz
o 3.3V and 12V Supply Voltages
Ordering Information
PART
TEMP RANGE
MAX9670CTL+
0°C to +70°C
40 TQFN-EP*
MAX9671CTH+
0°C to +70°C 44 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
TV R+L
AUDIO
INPUTS
No
Yes
*EP = Exposed pad.
System Block Diagram
V12
12V
STB CHIP
VVID
3.3V
VAUD
3.3V
MAX9670/MAX9671
RGB, Y/C, CVBS
I2C
Set-Top Boxes
µC
TVs
PINPACKAGE
I2C INTERFACE
REGISTERS AND
ACTIVITY
MONITOR
INTERRUPT
OUTPUT
DVD Players
CVBS
L/R AUDIO
(MAX9671 ONLY)
L/R AUDIO
(MAX9670 ONLY)
TV
SCART
SLOW SWITCHING
VIDEO
ENCODER
STEREO
AUDIO
DAC
RGB, Y/C, CVBS
SINGLE-ENDED R/L
STEREO AUDIO
VIDEO FILTERS AND
CROSSPOINT
FAST SWITCHING
AUDIO CROSSPOINT
WITH DIRECTDRIVE
OUTPUTS, VOLUME
CONTROL
RGB, Y/C, CVBS
Y/C, CVBS
L/R AUDIO
VCR
SCART
SLOW SWITCHING
SLOW SWITCHING
FAST SWITCHING
FAST SWITCHING
Typical Application Circuit appears at end of data sheet.
CHARGE PUMP
DirectDrive is a registered trademark of Maxim Integrated
Products, Inc.
EP
GNDVID
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX9670/MAX9671
General Description
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
ABSOLUTE MAXIMUM RATINGS
Continuous Power Dissipation (TA = +70°C)
40-Pin TQFN-EP (derate 26.3mW/°C above +70°C) ...2105.3mW
44-Pin TQFN-EP (derate 26.3mW/°C above +70°C)...2222.2mW
Operating Temperature Range...............................0°C to +70°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
VVID to GNDVID........................................................-0.3V to +4V
V12 to EP.................................................................-0.3V to +14V
VAUD to EP ...............................................................-0.3V to +4V
EP to GNDVID .......................................................-0.1V to +0.1V
All Video Inputs, VCRIN_FS to GNDVID...................-0.3V to +4V
All Audio Inputs to EP .........................................-1V to (EP + 1V)
SDA, SCL, DEV_ADDR, INT to GNDVID ..................-0.3V to +4V
TV_SS, VCR_SS to EP .................................-0.3V to (V12 + 0.3V)
Current
All Video/Audio Inputs ...................................................±20mA
C1P, C1N, CPVSS .........................................................±50mA
Output Short-Circuit Current Duration
Video and Fast-Switching Outputs to VVID,
GNDVID.................................................................Continuous
Audio Outputs to VAUD, EP .....................................Continuous
TV_SS, VCR_SS to V12, EP......................................Continuous
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V12 = 12V, VVID = VAUD = 3.3V, VGNDVID = VEP = 0V, no load, TA = 0°C to +70°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
Video Supply Voltage Range
VVID
Inferred from video PSRR test at 3V and
3.6V
Audio Supply Voltage Range
VAUD
Inferred from audio PSRR test at 3V and
3.6V
V12 Supply Voltage Range
V12
Inferred from slow-switching levels
Normal operation; all video output
amplifiers are enabled and muted (Note 2)
VVID Quiescent Supply Current
IVID_Q
MIN
TYP
MAX
UNITS
3
3.3
3.6
V
3
3.3
3.6
V
11.4
12
12.6
V
16
30
mA
Standby mode, slow switch inputs low
1500
Shutdown
VAUD Quiescent Supply Current
V12 Quiescent Supply Current
IAUD_Q
I12_Q
35
Normal operation (Note 2)
3.2
Shutdown
Normal operation
(Note 2)
Slow-switching output
set to low-level
0.3
Slow-switching output
set to medium-level
475
µA
6
mA
35
µA
100
µA
Shutdown, TA = +25°C
10
µA
1.15
VP-P
VIDEO CHARACTERISTICS
DC-COUPLED INPUT
Input Voltage Range
VIN
Input Current
IIN
Input Resistance
RIN
2
RL = 75Ω to
GNDVID or 150Ω
to VVID/2; inferred
from gain test
VVID = 3V
1.15
VVID = 3.135V
VVID = 3.3V
VIN = 0.3V, TA = +25°C
1.3
1
300
_______________________________________________________________________________________
2
µA
kΩ
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
(V12 = 12V, VVID = VAUD = 3.3V, VGNDVID = VEP = 0V, no load, TA = 0°C to +70°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
-13
-4
+6
mV
2
%
2
µA
AC-COUPLED INPUT
Sync-Tip Clamp Level
VCLP
Sync-tip clamp
Sync Crush
Sync-tip clamp; percentage reduction in
sync pulse (0.3VP-P); guaranteed by input
clamping current measurement, TA = +25°C
Input Clamping Current
Sync-tip clamp, VIN = 0.3V, TA = +25°C
Maximum Input Source
Resistance
Input sync-tip circuit must be stable even if
the source resistance is as high as 300Ω
Input Voltage
Input Resistance
1
Ω
300
Bias circuit
0.57
High-impedance input circuit
0.3 x
VVID
0.6
0.63
0.36 x
VVID
Bias circuit
10
High-impedance input circuit
222
V
kΩ
DC CHARACTERISTICS
DC Voltage Gain
Av
DC Gain Mismatch Among R, G,
and B Outputs
Output Level
Guaranteed by output voltage swing
Guaranteed by output voltage swing of
TV_R/C_OUT, TV_G_OUT, and TV_B_OUT;
first input signal set is VCR_R/C_IN,
VCR_G_IN, and VCR_B_IN; second signal
set is ENC_R/C_IN, ENC_G_IN, and
ENC_B_IN
Sync-tip clamp (VIN = VCLP)
1.95
0.1
0.30
0.51
Bias circuit
1.3
1.5
1.78
-2
Sync-tip clamp, measured at output,
VVID = 3V, VIN = VCLP to (VCLP +1.15V),
RL = 150Ω to VVID/2, RL = 75Ω to GNDVID
Measured at output, VVID = 3.135V, VIN =
VCLP to (VCLP + 1.15V), RL = 150Ω to
VVID/2, RL = 75Ω to GNDVID
2
2.05
V/V
+2
%
2.3
2.243
2.3
2.358
VP-P
Output Voltage Swing
Bias circuit, measured at output, VVID = 3V,
VIN = (VBIAS - 0.575V) to (VBIAS + 0.575V),
RL = 150Ω to VVID/2, RL = 75Ω to GNDVID
Measured at output, VVID = 3.135V,
VIN = (VBIAS - 0.575V) to (VBIAS + 0.575V),
RL = 150Ω to VVID/2, RL = 75Ω to GNDVID
2.3
2.243
Output Short-Circuit Current
Output Resistance
V
2.3
2.358
100
ROUT
mA
Ω
0.5
Output Leakage Current
Output disabled (load detection not active)
Power-Supply Rejection Ratio
3V ≤ VVID ≤ 3.6V
170
35
µA
dB
_______________________________________________________________________________________
3
MAX9670/MAX9671
ELECTRICAL CHARACTERISTICS (continued)
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
ELECTRICAL CHARACTERISTICS (continued)
(V12 = 12V, VVID = VAUD = 3.3V, VGNDVID = VEP = 0V, no load, TA = 0°C to +70°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
AC CHARACTERISTICS
VOUT = 2VP-P, f = 100kHz to 5.5MHz
Filter Passband Flatness
3
f = 27MHz
40
Filter Attenuation
VOUT = 2VP-P,
attenuation is
referred to 100kHz
Slew Rate
VOUT = 2VP-P, no filter in video path
Settling Time
-1
f = 9.5MHz
f = 54MHz
dB
dB
55
60
V/µs
ns
VOUT = 2VP-P, settle to 0.1% (Note 3)
400
Differential Gain
DG
5-step modulated staircase, f = 4.43MHz
0.15
%
Differential Phase
DP
5-step modulated staircase, f = 4.43MHz
0.5
Degrees
2T Pulse-to-Bar K Rating
2T = 200ns, bar time is 18µs, the beginning
2.5% and the ending 2.5% of the bar time is
ignored
0.3
K%
2T Pulse Response
2T = 200ns
0.2
K%
2T Bar Response
2T = 200ns, bar time is 18µs, the beginning
2.5% and the ending 2.5% of the bar time is
ignored
0.2
K%
Nonlinearity
Group Delay Distortion
5-step staircase
100kHz ≤ f ≤ 5MHz, outputs are 2VP-P
0.1
11
%
ns
Glitch Impulse Caused by
Charge-Pump Switching
Measured at outputs
100
pV-s
Peak Signal to RMS Noise
100kHz ≤ f ≤ 5MHz
70
dB
Power-Supply Rejection Ratio
f = 100kHz, 100mVP-P
47
dB
Output Impedance
f = 5MHz
2
Ω
Video Crosstalk
f = 4.43MHz
-80
dB
Reverse Isolation
VCR SCART inputs to encoder inputs,
full-power mode with VCR being looped
through to TV, f = 4.43MHz
92
dB
Pulldown Resistance
Enable VCR_R/C_OUT pulldown through
I2C interface
4.4
7.5
Ω
4.05
V/V
+1.5
%
AUDIO CHARACTERISTICS
Voltage Gain
VIN = -0.707V to +0.707V
3.95
Gain Mismatch
VIN = -0.707V to +0.707V
-1.5
4
Flatness
f = 20Hz to 20kHz, 0.25VRMS input
0.006
dB
Frequency Bandwidth
0.25VRMS input, frequency where output is
-3dB referenced to 1kHz
230
kHz
Capacitive Drive
No sustained oscillations; 75Ω series
resistor on output
300
pF
4
_______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
(V12 = 12V, VVID = VAUD = 3.3V, VGNDVID = VEP = 0V, no load, TA = 0°C to +70°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
Input Resistance
VIN = -0.707V to +0.707V
Input Bias Current
VIN = 0, TA = +25°C
Input Signal Amplitude
f = 1kHz, THD < 1%
Output DC Level
Power-Supply Rejection Ratio
MIN
TYP
MAX
10
MΩ
500
0.5
No input signal, VIN grounded
-4
DC
75
f = 1kHz
+4
f = 1kHz, 0.25VRMS input, 20Hz to 20kHz
RL = 3.33kΩ, f = 1kHz, 0.25VRMS input
0.002
RL = 3.33kΩ, f = 1kHz, 0.5VRMS input
0.001
mV
dB
90
Total Harmonic Distortion Plus
Noise
nA
VRMS
100
Signal-to-Noise Ratio
UNITS
96
dB
%
0.4
Ω
2
dB
Volume Control Minimum
Attenuation
0
dB
Volume Control Maximum
Attenuation
62
dB
Output Impedance
f = 1kHz
Volume Control Attenuation Step
Programmable gain to TV SCART volume
control from -62dB to 0
Mute Suppression
f = 1kHz, 0.25VRMS input
110
dB
Audio Crosstalk
f = 1kHz, 0.25VRMS input
100
dB
Video input: f = 15kHz, 1VP-P signal
Audio input: f = 15kHz, 0.5VRMS signal
92
dB
570
kHz
VIDEO-TO-AUDIO INTERACTION
Crosstalk
CHARGE PUMP
Switching Frequency
FAST SWITCHING
Input Low
0.4
Input High Level
1
Input Current
TA = +25°C
Output Low Voltage
IOL = 0.5mA
Output High Voltage
IOH = 0.5mA
V
V
10
µA
0.1
V
VVID 0.1
V
7
Ω
Rise Time
143Ω to GNDVID
12
ns
Fall Time
143Ω to GNDVID
10
ns
Output Resistance
SLOW SWITCHING
Input Low Voltage
Input Medium Voltage
4.5
Input High Voltage
9.5
2
V
7
V
V
_______________________________________________________________________________________
5
MAX9670/MAX9671
ELECTRICAL CHARACTERISTICS (continued)
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
ELECTRICAL CHARACTERISTICS (continued)
(V12 = 12V, VVID = VAUD = 3.3V, VGNDVID = VEP = 0V, no load, TA = 0°C to +70°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
Input Current
TYP
MAX
UNITS
70
100
µA
Output Low Voltage
10kΩ to EP, 11.4V ≤ V12 ≤ 12.6V
Output Medium Voltage
10kΩ to EP, 11.4V ≤ V12 ≤ 12.6V
5
Output High Voltage
10kΩ to EP, 11.4V ≤ V12 ≤ 12.6V
10
V
0.7 x
VVID
V
1.5
V
6.5
V
DIGITAL INTERFACE
Input High Voltage
VIH
Input Low Voltage
VIL
Input Hysteresis
VHYS
Input Leakage Current
IIH, IIL
0.3 x
VVID
0.06 x
VVID
TA = +25°C
-1
Input Capacitance
V
+1
6
Input Current
0.1VVID < SDA < 3.3V,
0.1VVID < SCL < 3.3V
I/O pins of fast-mode devices must not
obstruct the SDA and SCL lines if V+ is
switched off, TA = +25°C
ISINK = 6mA
V
µA
pF
-10
+10
µA
0.4
V
400
kHz
Output Low Voltage SDA
VOL
Serial-Clock Frequency
fSCL
0
Bus Free Time Between a STOP
and a START Condition
tBUF
1.3
µs
tHD, STA
0.6
µs
Low Period of the SCL Clock
tLOW
1.3
µs
High Period of the SCL Clock
tHIGH
0.6
µs
Setup Time for a Repeated
START Condition
tSU, STA
0.6
µs
Data Hold Time
tHD, DAT
Data Setup Time
tHD, DAT
Hold Time, (Repeated) START
Condition
Fall Time of SDA Transmitting
Setup Time for STOP Condition
Pulse Width of Spike Suppressed
6
tF
(Note 4)
0.9
100
ISINK ≤ 6mA, CB = total capacitance of one
bus line in pF, tR and tF measured between
0.3VVID and 0.7VVID
tSU, STO
tSP
0
ns
100
ns
0.6
Input filters on the SDA and SCL inputs
suppress noise spikes less than 50ns
µs
0
_______________________________________________________________________________________
µs
50
ns
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
(V12 = 12V, VVID = VAUD = 3.3V, VGNDVID = VEP = 0V, no load, TA = 0°C to +70°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
0.3 x
VVID
V
OTHER DIGITAL I/O
DEV_ADDR Low Level
0.7 x
VVID
DEV_ADDR High Level
V
DEV_ADDR Input Current
TA = +25°C
+1
µA
Interrupt Output Low Voltage
IOL = 0.5mA
0.1
V
Interrupt Output Leakage Current
INT high impedance, TA = +25°C
10
µA
Note 1:
Note 2:
Note 3:
Note 4:
-1
All devices are 100% production tested at TA = +25°C. Specifications over temperature limits are guaranteed by design.
Normal operation mode is full power with input video and load detection active.
The settling time is measured from the 50% of the input swing to the 0.1% of the final value of the output.
A master device must provide a hold time of at least 300ns for the SDA signal (referred to VIL of the SCL signal) to bridge
the undefined region of SCL’s falling edge.
Typical Operating Characteristics
(VVID = VAUD = 3.3V, V12 = 12V, VGNDVID = VEP = 0V, video load is 150Ω to GNDVID, audio load is 10kΩ to EP, TA = +25°C, unless
otherwise noted.)
0
-1
NO FILTER
GAIN (dB)
GAIN (dB)
-10
VOUT = 100mVP-P
1
-20
FILTER
-30
VOUT = 2VP-P
0
-10
NO FILTER
-2
-3
FILTER
-4
-5
-40
10
MAX9670 toc03
0
2
NO FILTER
GAIN (dB)
VOUT = 100mVP-P
MAX9670 toc01
10
LARGE-SIGNAL GAIN
vs. FREQUENCY
SMALL-SIGNAL GAIN FLATNESS
vs. FREQUENCY
MAX9670 toc02
SMALL-SIGNAL GAIN
vs. FREQUENCY
-20
FILTER
-30
-40
-6
-50
-50
-7
-8
-60
100k
1M
10M
FREQUENCY (Hz)
100M
1G
-60
1M
10M
FREQUENCY (Hz)
100M
100k
1M
10M
100M
1G
FREQUENCY (Hz)
_______________________________________________________________________________________
7
MAX9670/MAX9671
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics (continued)
(VVID = VAUD = 3.3V, V12 = 12V, VGNDVID = VEP = 0V, video load is 150Ω to GNDVID, audio load is 10kΩ to EP, TA = +25°C, unless
otherwise noted.)
NO FILTER
-20
-1
140
VOUT = 2VP-P
120
100
-2
-3
-4
FILTER
-60
DELAY (ns)
-40
DELAY (ns)
ALL HOSTILE
-80
-5
-6
-100
10M
100M
1M
100k
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FREQUENCY (Hz)
VIDEO POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
VIDEO VOLTAGE GAIN
vs. TEMPERATURE
VIDEO OUTPUT VOLTAGE
vs. INPUT VOLTAGE
FILTER
-20
-25
-30
NO FILTER
-35
2.02
3.0
OUTPUT VOLTAGE (V)
-15
2.03
OUTPUT VOLTAGE (V)
-10
3.5
MAX9670 toc08
2.04
MAX9670 toc07
0
-5
PSRR (dB)
NO FILTER
0
1M
100k
100M
10M
60
20
-120
1M
FILTER
40
-7
-8
80
2.01
2.00
1.99
1.98
MAX9670 toc09
GAIN (dB)
VOUT = 100mVP-P
MAX9670 toc06
1
MAX9670 toc05
0
MAX9670 toc04
2
0
GROUP DELAY
vs. FREQUENCY
VIDEO CROSSTALK
vs. FREQUENCY
LARGE-SIGNAL GAIN FLATNESS
vs. FREQUENCY
2.5
2.0
1.5
1.0
-40
0.5
1.97
-45
1.96
-50
100k
1M
10M
0
25
0
100M
8
0
1
1
2
2
3
3
4
4
5
5
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
75
0
0.4
0.8
INPUT VOLTAGE (V)
DIFFERENTIAL GAIN AND PHASE
2T WITH FILTER
1.2
1.6
MAX9670 toc12
MAX9670 toc11
DIFFERENTIAL GAIN (%)
0
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
DIFFERENTIAL PHASE (deg)
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
MAX9670 toc10
DIFFERENTIAL GAIN (%)
DIFFERENTIAL GAIN AND PHASE
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
50
INPUT VOLTAGE (V)
FREQUENCY (Hz)
DIFFERENTIAL PHASE (deg)
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
VIDEO INPUT
200mV/div
0
1
2
3
4
5
VIDEO OUTPUT
500mV/div
0
1
2
3
4
5
80ns/div
_______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
2T NO FILTER
12.5T WITH FILTER
MAX9670 toc13
MAX9670 toc14
VIDEO INPUT
200mV/div
VIDEO INPUT
200mV/div
VIDEO OUTPUT
500mV/div
VIDEO OUTPUT
500mV/div
80ns/div
1µs/div
12.5T NO FILTER
NTC7 WITH FILTER
MAX9670 toc15
MAX9670 toc16
VIDEO INPUT
200mV/div
VIDEO INPUT
500mV/div
VIDEO OUTPUT
500mV/div
VIDEO OUTPUT
1V/div
1µs/div
10µs/div
NTC7 NO FILTER
FIELD SQUARE WAVE
MAX9670 toc17
10µs/div
MAX9670 toc18
VIDEO INPUT
500mV/div
VIDEO INPUT
500mV/div
VIDEO OUTPUT
1V/div
VIDEO OUTPUT
1V/div
2ms/div
_______________________________________________________________________________________
9
MAX9670/MAX9671
Typical Operating Characteristics (continued)
(VVID = VAUD = 3.3V, V12 = 12V, VGNDVID = VEP = 0V, video load is 150Ω to GNDVID, audio load is 10kΩ to EP, TA = +25°C, unless
otherwise noted.)
Typical Operating Characteristics (continued)
(VVID = VAUD = 3.3V, V12 = 12V, VGNDVID = VEP = 0V, video load is 150Ω to GNDVID, audio load is 10kΩ to EP, TA = +25°C, unless
otherwise noted.)
VIDEO INPUT SYNC-TIP CLAMP VOLTAGE
vs. TEMPERATURE
0
-1
-2
-3
-4
615
-5
605
600
595
590
580
0
25
50
75
25
0
50
75
TEMPERATURE (°C)
TEMPERATURE (°C)
VIDEO INPUT SYNC-TIP CLAMP CURRENT
vs. TEMPERATURE
VIDEO INPUT SYNC-TIP CLAMP CURRENT
vs. INPUT VOLTAGE
1.2
1.1
1.0
0.9
0.8
MAX9670 toc22
1.3
8
7
INPUT CLAMP CURRENT (µA)
MAX9670 toc21
1.4
6
5
4
3
2
1
0.7
0
0.6
0
25
50
0
75
0.5
1.0
1.5
2.0
2.5
3.0
TEMPERATURE (°C)
INPUT VOLTAGE (V)
VIDEO OUTPUT BIAS VOLTAGE
vs. TEMPERATURE
AUDIO LARGE-SIGNAL GAIN
vs. FREQUENCY
10
MAX9670 toc23
1.50
1.49
3.5
MAX9670 toc24
INPUT CLAMP CURRENT (mA)
610
585
-6
5
1.48
0
GAIN (dB)
1.47
1.46
1.45
-5
-10
1.44
-15
1.43
1.42
-20
0
25
50
TEMPERATURE (°C)
10
MAX9670 toc20
620
INPUT BIAS VOLTAGE (mV)
1
INPUT CLAMP VOLTAGE (mV)
VIDEO INPUT BIAS VOLTAGE
vs. TEMPERATURE
MAX9670 toc19
2
OUTPUT BIAS VOLTAGE (V)
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
75
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
AUDIO CROSSTALK
vs. FREQUENCY
-20
VIN = 0.25VRMS
-40
0.01
THD+N (%)
CROSSTALK (dB)
0.1
MAX9670 toc25
0
MAX9670 toc26
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
-60
-80
TVIN TO
TVOUT
TVIN TO
VCROUT
0.001
-100
-120
0.0001
10
100
1k
10k
100k
1k
10k
VAUD POWER-SUPPLY REJECTION RATIO
(INPUT REFERRED) vs. FREQUENCY
VVID QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE
-20
25
CURRENT (mA)
-40
-60
100k
MAX9670 toc28
30
MAX9670 toc27
VAUD = 3.3V + 100mVP-P
20
15
-80
10
-100
5
0
-120
100
1k
10k
0
100k
25
50
FREQUENCY (Hz)
TEMPERATURE (°C)
VAUD QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE
V12 QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE
800
MAX9670 toc29
5
4
75
MAX9670 toc30
10
700
600
CURRENT (nA)
CURRENT (mA)
100
FREQUENCY (Hz)
0
PSRR (dB)
10
FREQUENCY (Hz)
3
2
500
400
300
200
1
100
0
0
0
25
50
TEMPERATURE (°C)
75
0
25
50
75
TEMPERATURE (°C)
______________________________________________________________________________________
11
MAX9670/MAX9671
Typical Operating Characteristics (continued)
(VVID = VAUD = 3.3V, V12 = 12V, VGNDVID = VEP = 0V, video load is 150Ω to GNDVID, audio load is 10kΩ to EP, TA = +25°C, unless
otherwise noted.)
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Pin Description
PIN
NAME
FUNCTION
MAX9670
MAX9671
1
1
SDA
Bidirectional I2C Data I/O. Output is open drain and tolerates up to 3.6V.
2
2
SCL
I2C Clock Input
3
3
DEV_ADDR
Device Address Set Input. Connect to GNDVID, VVID, SDA or SCL. See Table 3.
Interrupt Output. This is an open-drain output that pulls down to GNDVID to
indicate a change in the VCR slow switching or fast switching input, the activity
status of the composite video inputs, or the load status of the composite video
outputs.
12
4
4
INT
5
5
VAUD
Audio Supply. Connect to a 3.3V supply. Bypass with a 10µF aluminum
electrolytic capacitor and a 0.47µF ceramic capacitor to EP.
6
6
C1P
Charge-Pump Flying Capacitor Positive Terminal. Connect a 0.47µF capacitor
from C1P to C1N.
7
7
C1N
Charge-Pump Flying Capacitor Negative Terminal. Connect a 0.47µF capacitor
from C1P to C1N.
8
8
CPVSS
9
9
ENC_INL
Encoder Left-Channel Audio Input
10
10
ENC_INR
Encoder Right-Channel Audio Input
—
11
TV_INL
TV SCART Left-Channel Audio Input
—
12
TV_INR
TV SCART Right-Channel Audio Input
11
13
VCR_INL
VCR SCART Left-Channel Audio Input
12
14
VCR_INR
VCR SCART Right-Channel Audio Input
13
15
TV_OUTL
TV SCART Left-Channel Audio Output
14
16
VCR_OUTL
VCR SCART Left-Channel Audio Output
15
17
VCR_OUTR
VCR SCART Right-Channel Audio Output
16
18
TV_OUTR
17
19
TV_SS
V12
Charge-Pump Negative Power Supply. Bypass with a 1µF ceramic capacitor to EP.
TV SCART Right-Channel Audio Output
TV SCART Bidirectional Slow-Switch Signal
+12V Supply for the Slow Switching Circuit. Bypass with a 10µF + 0.47µF ceramic
capacitor to EP.
18
20
19
21
VCR_SS
20
22
TVOUT_FS
—
23, 44
N.C.
21
24
VCRIN_FS
VCR SCART Fast-Switching Logic Input
22
25
ENC_B_IN
Encoder Blue Video Input
23
26
ENC_G_IN
Encoder Green Video Input
24
27
VCR_B_IN
VCR SCART Blue Video Input
25
28
VCR_G_IN
VCR SCART Green Video Input
26
29
TV_B_OUT
TV SCART Blue Video Output
27
30
TV_G_OUT
TV SCART Green Video Output
VCR SCART Bidirectional Slow-Switch Signal
TV SCART Fast-Switching Logic Output
No Connection. Leave unconnected.
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
PIN
NAME
FUNCTION
MAX9670
MAX9671
28
31
GNDVID
29
32
VCR_R/C_IN
30
33
VVID
31
34
ENC_C_IN
32
35
ENC_R/C_IN
Encoder Red/Chroma Video Input
33
36
TV_R/C_OUT
TV SCART Red/Chroma Video Output
34
37
VCR_R/C_OUT
35
38
36
39
TV_Y/CVBS_OUT
TV SCART Luma/Composite Video Output
37
40
VCR_Y/CVBS_IN
VCR SCART Luma/Composite Video Input
38
41
TV_Y/CVBS_IN
39
42
ENC_Y_IN
40
43
ENC_Y/CVBS_IN
—
—
EP
Video Ground
VCR SCART Red/Chroma Video Input
Video and Digital Supply. Connect to a 3.3V supply. Bypass with parallel 1µF and
0.1µF ceramic capacitors to GNDVID. VVID also serves as a digital supply for the
I2C interface.
Encoder Chroma Video Input
VCR SCART Red/Chroma Video Output
VCR_Y/CVBS_OUT VCR SCART Luma/Composite Video Output
TV SCART Luma/Composite Video Input
Encoder Luma Video Input
Encoder SCART Luma/Composite Video Input
Exposed Pad. The exposed pad is the internal ground for the audio amplifiers and
charge pump. A low-impedance connection between ground and EP is required
for proper isolation.
Detailed Description
The MAX9670/MAX9671 represents Maxim’s third generation of SCART audio/video (A/V) switches. Under I2C
control, these devices route audio, video, and control
information between the set-top box decoder chip and
two SCART connectors. The audio signals are left audio
and right audio. The video signals are composite video
with blanking and sync (CVBS) and component video
(red, green, blue). S-video (Y/C) can be transported
across the SCART interface if CVBS is reassigned to
luma (Y) and red is reassigned to chroma (C). Support
for S-video is optional. The slow-switch signal and the
fast-switch signal carry control information. The slowswitch signal is a 12V, three-level signal that indicates
whether the picture aspect ratio is 4:3 or 16:9 or causes
the television to use an internal A/V source such as an
antenna. The fast-switch signal indicates whether the
television should display CVBS or RGB signals.
CVBS, left audio, and right audio are full duplex. All the
other signals are half duplex. Therefore, one device on
the link must be designated as the transmitter, and the
other device must be designated as the receiver.
The low power consumption and the advanced monitoring functions of the MAX9670/MAX9671 enable the cre-
ation of lower power set-top boxes, televisions, and
DVD players. Unlike competing SCART ICs, the audio
and video circuits of the MAX9670/MAX9671 operate
entirely from 3.3V rather than from 5V and 12V. Only the
slow-switch circuit of the MAX9670/MAX9671 requires a
12V supply. The MAX9670/MAX9671 also have circuits
that detect activity on the CVBS inputs, loads on the
CVBS outputs, and the level of the slow-switch signals.
The INT signal informs the microcontroller if there are
any changes so that the microcontroller can intelligently decide whether to power up or power down
the equipment.
In addition, the MAX9670/MAX9671 have DirectDrive
audio circuitry to eliminate click-and-pop noise. With
DirectDrive, the DC bias of the audio line outputs is
always at ground, no matter whether the MAX9670/
MAX9671 are being powered up or powered down.
Conventional audio line output drivers that operate from a
single supply require series AC-coupling capacitors.
During power-up, the DC bias on the AC-coupling capacitor moves from ground to a positive voltage, and during
power-down, the opposite occurs. The changing DC bias
usually causes an audible transient.
______________________________________________________________________________________
13
MAX9670/MAX9671
Pin Description (continued)
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
ZCD
MUTE
ENC_INL
MUTE
VCR_INL
VOLUME
CONTROL
0dB TO -62dB
(0.5VRMS FULL-SCALE INPUT)
MUTE
VOLUME
CONTROL
0dB TO -62dB
*TV_INL
x4
TV_OUTL
(2VRMS FULL-SCALE OUTPUT)
x4
TV_OUTR
x4
VCR_OUTL
MUTE
MUTE
ENC_INR
(2VRMS FULL-SCALE OUTPUT)
VCR_INR
x4
VCR_OUTR
MUTE
*TV_INR
SCL
REGISTER
CONTROL
SDA
DEV_ADDR
VAUD
C1P
CHARGE
PUMP
EP
C1N
CPVSS
MAX9670/MAX9671
*MAX9671 ONLY.
Figure 1. MAX9670/MAX9671 Audio Section Functional Diagram
Audio Section
The MAX9670 audio circuit is essentially a stereo,
2-by-2, nonblocking, audio crosspoint with output drivers. The encoder (stereo audio DAC) and the VCR are
the two input sources, and the two outputs go to the TV
SCART connector and the VCR SCART connector. See
Figure 1. The MAX9671 audio circuit is similar to that of
the MAX9670 except that it is a stereo, 3-by-2,
14
nonblocking audio crosspoint with TV as the third input
source.
The integrated charge pump inverts the +3.3V supply
to create a -3.3V supply. The audio circuit operates
from bipolar supplies so the audio signal is always
biased to ground.
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
VDD
VDD/2
GND
CONVENTIONAL DRIVER-BIASING SCHEME
+VDD
GND
VOUT
2VDD
-VDD
DirectDrive BIASING SCHEME
Figure 2. Conventional Driver Output Waveform vs. MAX9670/
MAX9671 Output Waveform.
Clickless Switching
The TV audio channel incorporates a zero-crossing
detect (ZCD) circuit that minimizes click noise due to
abrupt signal level changes that occur when switching
between audio signals at an arbitrary moment.
To implement the zero-crossing function when switching audio signals, set the ZCD bit high (Audio Control
register 00h, bit 6). Then set the mute bit high (Audio
Control register 00h, bit 0). Next, wait for a sufficient
period of time for the audio signal to cross zero. This
period is a function of the audio signal path’s low-frequency 3dB corner (fL3dB). Thus, if fL3dB = 20Hz, the
time period to wait for a zero-crossing detect is 1/20Hz
or 50ms.
After the wait period, select a new audio source for the
TV audio channel by writing to bits 1 and 0 of TV Audio
Control register (01h). Finally, clear mute (Audio Control
register, 00h, bit 0), but leave ZCD (Audio Control register 00h, bit 6) high. The MAX9670/MAX9671 switches
the signal out of mute at the next zero crossing. See
Tables 12 and 13.
Conventional single-supply audio line drivers have their
outputs biased about a nominal DC voltage (typically
half the supply) for maximum dynamic range. Large
coupling capacitors are needed to block this DC bias.
Clicks and pops are created when the coupling capacitors are charged during power-up and discharged during power-down.
The MAX9670/MAX9671 features a low-noise charge
pump that requires only two small ceramic capacitors.
The 580kHz switching frequency is well beyond the
audio range and does not interfere with audio signals.
The switch drivers feature a controlled switching speed
that minimizes noise generated by turn-on and turn-off
transients.
The SCART standard specifies 2VRMS as the full-scale
for audio signals. As the audio circuits process
0.5V RMS full-scale audio signals internal to the
MAX9670/MAX9671, the gain-of-4 output amplifiers
restore the audio signals to a full-scale of 2VRMS.
To select which audio input source is routed to the TV
SCART connector, write to bits 1 and 0 of the TV Audio
Control register (01h). To select which audio input
source is routed to the VCR SCART connector, write to
bits 3 and 2 of the TV Audio Control register (01h). The
power-on default is for the TV and VCR audio outputs to
be muted (the inputs of the output amplifiers are connected to audio ground). See Tables 10 and 13.
Volume Control
Volume control is programmable from -62dB to 0dB in
2dB steps through I2C interface. The block consists of
a resistive ladder network to generate 31 2dB volume
control steps, a unity gain buffer to isolate the input
from the resistive ladder, switches (MPLx and MNLx)
that select 1 of 32 nodes on the resistive ladder, and
logic to decode the the I2C volume control value. See
Table 12.
______________________________________________________________________________________
15
MAX9670/MAX9671
VDD
Audio Outputs
The MAX9670/MAX9671 audio output amplifiers feature
Maxim’s patented DirectDrive architecture, thereby
eliminating the need for output-coupling capacitors
required by conventional single-supply audio line drivers. An internal charge pump inverts the positive supply (VAUD), creating a negative supply (CPVSS). The
audio output amplifiers operate from these bipolar supplies with their outputs biased about audio ground
(Figure 2). The benefit of this audio ground bias is that
the amplifier outputs do not have a DC component. The
DC-blocking capacitors required with conventional
audio line drivers are unnecessary, conserving board
space, reducing system cost, and improving frequency
response.
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
ACTIVITY DETECT
ACTIVITY DETECT
ACTIVITY DETECT
MAX9670/MAX9671
ACTIVITY DETECT
TV_Y/CVBS_IN
CLAMP
VCR_Y/CVBS_IN
CLAMP
ENC_Y/CVBS_IN
CLAMP
ENC_Y_IN
CLAMP
LOAD SENSE
TV_Y/CVBS_OUT
AV = 2V/V
LPF
LPF
MUTE
LOAD SENSE
VCR_R/C_IN
CLAMP/BIAS
ENC_R/C_IN
CLAMP/BIAS
LPF
ENC_C_IN
CLAMP/BIAS
LPF
AV = 2V/V
VCR_Y/CVBS_OUT
AV = 2V/V
TV_R/C_OUT
AV = 2V/V
VCR_R/C_OUT
AV = 2V/V
TV_G_OUT
AV = 2V/V
TV_B_OUT
AV = 1V/V
TVOUT_FS
AV = 1V/V
TV_SS
AV = 1V/V
VCR_SS
MUTE
VCR_G_IN
CLAMP
ENC_G_IN
CLAMP
LPF
MUTE
VCR_B_IN
CLAMP
ENC_B_IN
CLAMP
LPF
MUTE
VVID
GNDVID
VCRIN_FS
0.7V
V12
+6V
EP
TO I2C
x1
V12
+6V
EP
TO I2C
x1
Figure 3. MAX9670/MAX9671 Video Section Function Diagram
Video Section
The video circuit routes different video formats between
the set-top box decoder, the TV SCART connector, and
16
the VCR SCART connector. It also routes slow-switch
and fast-switch control information. See Figure 3.
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
The transparent sync-tip clamp is transparent when the
incoming video signal is DC-coupled and at or above
ground. Under such conditions, the clamp never activates. Therefore, the outputs of video DACs that generate signals between 0 and 1V can be directly
connected to the MAX9670/MAX9671 inputs.
The bias circuit accepts AC-coupled chroma, which is
a subcarrier with the color information modulated onto
it. The bias voltage of the bias circuits is around
600mV.
ENC_R/C_IN and VCR_R/C_IN can receive either a red
video signal or a chroma video signal. Set the input configuration by writing to bits 7 and 3 of the VCR Video
Input Control register (08h). See Tables 10 and 16.
The MAX9670/MAX9671 also have video input detection. When activated, activity detect circuits check if
sync is present on incoming CVBS signals. If so, then
there is a valid video signal. Read bits 2, 3, 4, and 5 of
the Video Activity Status register (0Fh) to determine the
status of the CVBS inputs. See Table 21.
In high-impedance mode, the inputs to the MAX9670/
MAX9671 do not distort the video signal in case the outputs of the video DAC are also connected to another
video circuit such as a high-definition video filter amplifier. See the SCART Set-Top Box with Analog HD Outputs
section. The inputs in high-impedance mode are biased
at VVID/3, which is sufficiently above ground so that the
ESD diodes never forward biases as the video signal
changes. The input resistance is 222kΩ, which presents
negligible loading on the video current DAC.
Video Reconstruction Filter
The video DAC outputs of the set-top box decoder chip
need to be lowpass-filtered to reject the out-of-band
noise. The MAX9670/MAX9671 integrate sixth-order,
Butterworth filters. The filter passband (±1dB) is typically 5.5MHz, and the attenuation at 27MHz is 52dB. The
filters are suited for standard-definition video.
Video Outputs
The video output amplifiers can both source and sink
load current, allowing output loads to be DC- or ACcoupled. The amplifier output stage needs around
300mV of headroom from either supply rail. For video
signals with a sync pulse, the sync tip is typically at
300mV, as shown in Figure 4. For a chroma signal, the
blank level is typically at 1.5V, as shown in Figure 5.
If the supply voltage is greater than 3.135V (5% below
a 3.3V supply), each amplifier can drive two DC-coupled video loads to ground. If the supply is less than
3.135V, each amplifier can drive only one DC-coupled
or AC-coupled video load.
The SCART standard allows for video signals to have a
superimposed DC component within 0 and 2V.
Therefore, most video signals are DC-coupled at the
output. In the unlikely event that the video signal needs
to be AC-coupled, the coupling capacitors should be
220µF or greater to keep the highpass filter formed by
the 37.5Ω equivalent resistance of the video transmission line to a corner frequency of 4.8Hz or below to keep
it well below the 25Hz frame rate of the PAL standard.
The CVBS outputs have load sense circuits. If enabled,
each load sense circuit checks for a load eight times
per second by connecting an internal 15kΩ pullup
resistor to the output for 1ms. If the output is pulled up,
no load is present. If the output stays low, a load is connected. Read bits 1 and 3 to determine load status. See
Table 21.
The selection of video sources that are sent to the TV
SCART connector are controlled by bits 0 to 4 of the TV
______________________________________________________________________________________
17
MAX9670/MAX9671
Video Inputs
Whether the incoming video signal is AC-coupled or
DC-coupled into the MAX9670/MAX9671 depends
upon the origin, format, and voltage range of the video
signal. Table 1 below shows the recommended connections. Always AC-couple an external video signal
through a 0.1µF capacitor because its voltage is not
well defined (see the Typical Application Circuit ). For
example, the video transmitter circuit might have a different ground than the video receiver, thereby level
shifting the DC bias. 60Hz power line hum might cause
the video signal to change DC bias slowly.
Internal video signals that are between 0 and 1V can be
DC-coupled. Most video DACs generate video signals
between 0 and 1V because the video DAC sources current into a ground-referenced resistor. For the minority
of video DACs that generate video signals between
2.3V and 3.3V because the video DAC sinks current
from a VVID-referenced resistor, AC-couple the video
signal to the MAX9670/MAX9671.
The MAX9670/MAX9671 restore the DC level of incoming, AC-coupled video signals with either transparent
sync-tip clamps or bias circuits. When using an ACcoupled input, the transparent sync-tip clamp automatically clamps the input signal minimum to ground,
preventing it from going lower. A small current of 1µA
pulls down on the input to prevent an AC-coupled signal from drifting outside the input range of the part. Use
sync-tip clamps with CVBS, RGB, and luma signals.
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Video Input Control register (06h) while the selection of
video sources that are sent to the VCR SCART connector are controlled by bits 0 to 2 of the VCR Video Input
Control register (08h). See Tables 10, 14, and 16. The
video outputs can be enabled or disabled by bits 2
through 7 of the Output Enable register (0Dh). See
Table 18.
Slow Switching
The MAX9670/MAX9671 support the IEC 933-1,
Amendment 1, three-level slow switching that selects
the aspect ratio for the display (TV). Under I2C control,
the MAX9670/MAX9671 set the slow-switching output
voltage level. Table 2 shows the valid input levels of the
slow-switching signal and the corresponding operating
modes of the display device.
Two bidirectional ports are available for slow-switching
signals for the TV and VCR. The slow-switching input
status is continuously read and stored in the Status register (0Eh). The slow-switching outputs can be set to a
logic level or high impedance by writing to the TV Video
Output Control register (07h) and the VCR Video Output
Control register (09h). When enabled, INT becomes
active low if the voltage level changes on TV_SS or
VCR_SS. See Tables 10, 15, 17, and 20.
Fast Switching
The fast-switching signal was originally used to switch
between CVBS and RGB signals on a pixel-by-pixel
basis so that on-screen display (OSD) information
could be inserted. Since modern set-top box decoder
chips have integrated OSD circuitry, there is no need to
create OSD information using the older technique. Now,
the fast-switching signal is just used to switch between
CVBS and RGB signal sources.
Set the source of the fast-switching signal by writing to
bits 4 and 3 of the TV Video Output Control register
(07h). The fast-switching signal to the TV SCART connector can be enabled or disabled by bit 1 of the Output
Enable register (0Dh). See Tables 10, 15, and 18.
I2C Serial Interface
The MAX9670/MAX9671 feature an I2C/SMBus™-compatible, 2-wire serial interface consisting of a serial-data
line (SDA) and a serial-clock line (SCL). SDA and SCL
facilitate communication between the MAX9670/
MAX9671 and the master at clock rates up to 400kHz.
Figure 6 shows the 2-wire interface timing diagram. The
master generates SCL and initiates data transfer on the
bus. A master device writes data to the MAX9670/
MAX9671 by transmitting a START (S) condition, the
proper slave address with the R/W bit set to 0, followed
by the register address and then the data word. Each
transmit sequence is framed by a START and a STOP
(P) condition. Each word transmitted to the
MAX9670/MAX9671 is 8 bits long and is followed by an
acknowledge clock pulse. A master reads from the
MAX9670/MAX9671 by transmitting the slave address
with the R/W bit set to 0, the register address of the register to be read, a REPEATED START (Sr) condition, the
slave address with the R/W bit set to 1, followed by a
series of SCL pulses. The MAX9670/MAX9671 transmit
data on SDA in sync with the master-generated SCL
pulses. The master acknowledges receipt of each byte
of data. Each read sequence is framed by a START or
MAX9670 fig05
MAX9670 fig04
INPUT
200mV/div
INPUT
500mV/div
OUTPUT
500mV/div
20µs/div
Figure 4. MAX9670/MAX9671 Video Output with CVBS Signal,
Multiburst Video Test Signal Shown
18
OUTPUT
200mV/div
10µs/div
Figure 5. MAX9670/MAX9671 Video Output with Chroma (C)
Signal, Multiburst Video Test Signal Shown
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
SDA
tBUF
tSU, STA
tSU, DAT
tHD, STA
tHD, DAT
tLOW
tSP
tSU, STO
SCL
tHIGH
tHD, STA
tR
tF
START
CONDITION
REPEATED
START CONDITION
STOP
CONDITION
START
CONDITION
Figure 6. I2C Serial-Interface Timing Diagram
REPEATED START (Sr) condition, an acknowledge or a
not acknowledge, and a STOP (P) condition. SDA operates as both an input and an open-drain output. A
pullup resistor, typically greater than 500Ω, is required
on the SDA bus. SCL operates as only an input. A
pullup resistor, typically greater than 500Ω, is required
on SCL if there are multiple masters on the bus, or if the
master in a single-master system has an open-drain
SCL output. Series resistors in line with SDA and SCL
are optional. Series resistors protect the digital inputs of
the MAX9670/MAX9671 from high-voltage spikes on the
bus lines, and minimize crosstalk and undershoot of the
bus signals.
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the START and STOP
Conditions section). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START (S)
condition. A START condition is a high-to-low transition
on SDA with SCL high. A STOP condition is a low-tohigh transition on SDA while SCL is high (Figure 7). A
START condition from the master signals the beginning
of a transmission to the MAX9670/MAX9671. The master terminates transmission, and frees the bus, by issuing a STOP condition. The bus remains active if a
REPEATED START condition is generated instead of a
STOP condition.
S
Sr
P
SCL
SDA
Figure 7. START, STOP, and REPEATED START Conditions
Early STOP Conditions
The MAX9670/MAX9671 recognize a STOP condition at
any point during data transmission except if the STOP
condition occurs in the same high pulse as a START
condition. For proper operation, do not send a STOP
condition during the same SCL high pulse as the
START condition.
Slave Address
The slave address is defined as the 7 most significant
bits (MSBs) followed by the read/write (R/W) bit. Set the
R/W bit to 1 to configure the MAX9670/MAX9671 to
read mode. Set the R/W bit to 0 to configure the
MAX9670/MAX9671 to write mode. The slave address
is always the first byte of information sent to the
MAX9670/MAX9671 after a START or a REPEATED
START condition. The MAX9670/MAX9671 slave
address is configurable with DEV_ADDR. Table 3
shows the possible slave addresses for the
MAX9670/MAX9671.
______________________________________________________________________________________
19
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9670/MAX9671 use to handshake receipt of each
byte of data when in write mode (see Figure 8). The
MAX9670/MAX9671 pull down SDA during the entire
master-generated ninth clock pulse if the previous byte
is successfully received. Monitoring ACK allows for
detection of unsuccessful data transfers. An unsuccessful data transfer occurs if a receiving device is
busy or if a system fault has occurred. In the event of
an unsuccessful data transfer, the bus master may retry
communication. The master pulls down SDA during the
ninth clock cycle to acknowledge receipt of data when
Write Data Format
A write to the MAX9670/MAX9671 consists of transmitting a START condition, the slave address with the R/W
bit set to 0, one data byte to configure the internal register address pointer, one or more data bytes, and a
STOP condition. Figure 9 illustrates the proper frame
format for writing one byte of data to the
MAX9670/MAX9671. Figure 10 illustrates the frame format for writing n bytes of data to the MAX9670/
MAX9671.
CLOCK PULSE FOR
ACKNOWLEDGMENT
START
CONDITION
SCL
the MAX9670/MAX9671 are in read mode. An acknowledge is sent by the master after each read byte to allow
data transfer to continue. A not acknowledge is sent
when the master reads the final byte of data from the
MAX9670/MAX9671, followed by a STOP (P) condition.
1
2
8
The slave address with the R/W bit set to 0 indicates
that the master intends to write data to the MAX9670/
MAX9671. The MAX9670/MAX9671 acknowledge
receipt of the address byte during the master-generated ninth SCL pulse.
The second byte transmitted from the master configures the MAX9670/MAX9671’s internal register address
pointer. The pointer tells the MAX9670/MAX9671 where
to write the next byte of data. An acknowledge pulse is
sent by the MAX9670/MAX9671 upon receipt of the
address pointer data.
9
NOT ACKNOWLEDGE
SDA
ACKNOWLEDGE
Figure 8. Acknowledge
ACKNOWLEDGE FROM MAX9670/MAX9671
B7
ACKNOWLEDGE FROM MAX9670/MAX9671
SLAVE ADDRESS
S
0
B6
B5
B4
B3
B2
B1
B0
ACKNOWLEDGE FROM MAX9670/MAX9671
A
REGISTER ADDRESS
A
DATA BYTE
A
R/W
P
1 BYTE
Figure 9. Writing a Byte of Data to the MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
ACKNOWLEDGE FROM MAX9670/MAX9671
ACKNOWLEDGE FROM MAX9670/MAX9671
S
SLAVE ADDRESS
0
A
REGISTER ADDRESS
R/W
B7 B6 B5 B4 B3 B2 B1 B0
B7 B6 B5 B4 B3 B2 B1 B0
A
DATA BYTE 1
A
1 BYTE
DATA BYTE n
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
Figure 10. Writing n Bytes of Data to the MAX9670/MAX9671
20
______________________________________________________________________________________
A
P
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
S
SLAVE ADDRESS
0
A
REGISTER ADDRESS
R/W
NOT ACKNOWLEDGE FROM MASTER
ACKNOWLEDGE FROM
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
A
Sr
SLAVE ADDRESS
REPEATED START
1
R/W
A
DATA BYTE
A
P
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
Figure 11. Reading One Indexed Byte of Data from the MAX9670/MAX9671
S
SLAVE ADDRESS
0
R/W
ACKNOWLEDGE FROM
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
A
REGISTER ADDRESS
A
Sr
SLAVE ADDRESS
REPEATED START
1
R/W
A
DATA BYTE
A
P
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
Figure 12. Reading n Bytes of Indexed Data from the MAX9670/MAX9671
The third byte sent to the MAX9670/MAX9671 contains
the data that is written to the chosen register. An
acknowledge pulse from the MAX9670/MAX9671 signals receipt of the data byte. The address pointer
autoincrements to the next register address after each
received data byte. This autoincrement feature allows a
master to write to sequential register address locations
within one continuous frame. The master signals the
end of transmission by issuing a STOP (P) condition.
Read Data Format
The master presets the address pointer by first sending
the MAX9670/MAX9671’s slave address with the R/W
bit set to 0 followed by the register address after a
START (S) condition. The MAX9670/MAX9671 acknowledges receipt of its slave address and the register
address by pulling SDA low during the ninth SCL clock
pulse. A REPEATED START (Sr) condition is then sent
followed by the slave address with the R/W bit set to 1.
The MAX9670/MAX9671 transmits the contents of the
specified register. Transmitted data is valid on the rising edge of the master-generated serial clock (SCL).
The address pointer autoincrements after each read
data byte. This autoincrement feature allows all registers to be read sequentially within one continuous
frame. A STOP condition can be issued after any number of read data bytes. If a STOP condition is issued
followed by another read operation, the first data byte
to be read is from the register address location set by
the previous transaction and not 00h and subsequent
reads autoincrement the address pointer until the next
STOP condition. Attempting to read from register
addresses higher than 01h results in repeated reads
from a dummy register containing FFh data. The master
acknowledges receipt of each read byte during the
acknowledge clock pulse. The master must acknowledge all correctly received bytes except the last byte.
The final byte must be followed by a not acknowledge
from the master and then a STOP condition. Figures 11
and 12 illustrate the frame format for reading data from
the MAX9670/MAX9671.
Interrupt Output
When interrupt is enabled in modes 1 and 2, INT, which
is an open-drain output, pulls low under the following
conditions: slow-switch signals change value, CVBS
input signals are detected or disappear, and CVBS output loads are added or removed.
When interrupt is enabled in mode 3, INT pulls low only
when the slow-switch signal changes value.
Enable INT by writing a 1 into bit 4 of register 01h. See
Table 13.
The interrupt can be cleared by reading register 0Eh
and 0Fh.
Applications Information
Audio Inputs
The maximum full-scale audio signal that can be
applied to the audio inputs is 0.5V RMS biased at
ground. The recommended application circuit to attenuate and bias an incoming audio signal is shown in
Figure 13.
______________________________________________________________________________________
21
MAX9670/MAX9671
ACKNOWLEDGE FROM
MAX9670/MAX9671
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
STEREO
AUDIO
DACS
1µF
MAX9670
6.65kΩ
ENC_INL
R1*
1µF
6.65kΩ
ENC_INR
R1*
*R1 VALUES
DAC = CS4334/5/8/9: R1 = 4.53kΩ, 1%
DAC = PCM1742: R1 = 5.57kΩ, 1%
Figure 13. Application circuit to connect audio source to audio
inputs. The 1µF capacitor connected to the ground-referenced
resistors biases the audio signal at ground. The resistors attenuate the audio signal.
The audio path has a gain of 4V/V so that the full scale
of the audio output signal is 2VRMS. If less than 2VRMS,
full scale is desired at the audio outputs, and the full
scale of the audio input signal should be proportionately decreased below 0.5VRMS.
Operating Modes
The MAX9670/MAX9671 has four operating modes,
which can be set by writing to bits 6 and 7 of register
10h. See Table 19.
considers this condition to be illegal and does not loop
through any signals.
A finite state machine (Figure 14) controls the operation
of the MAX9670/MAX9671. State 0 is always the initial
state when the MAX9670/MAX9671 enter standby
mode. Table 4 shows the values of the I2C registers in
state 0. The state machine sets the other I2C registers
to the correct values to loop through the audio/video
signals in states 1 and 2 (see Tables 5 and 6). When
the MAX9670/MAX9671 leaves standby mode, the values in all of the I2C registers except register 10h are
preserved so that the operation is not disturbed. For
example, if in standby mode, the MAX9670 is looping
through the audio/video signals from VCR SCART to TV
SCART, and if the microcontroller changes the operating mode from standby mode to full-power mode, the
audio/video signals continue to be looped through during and after the mode change. The user does not
experience any disruption in audio or video service.
The microcontroller can be turned off in standby mode
because the MAX9670/1 operate autonomously. Upon
power-up, the default operating mode is standby mode.
Full-Power Mode with Video Input Detection
and Video Load Detection
In this mode, the MAX9670/MAX9671 are fully on. If
interrupt is enabled, INT goes active low whenever the
slow-switch signal changes; a CVBS signal appears or
disappears; or a CVBS load appears or disappears.
The microcontroller can decide whether to change the
routing configuration or operating mode of the
MAX9670/MAX9671.
Shutdown
All circuitry is shutdown in the MAX9670/MAX9671
except for the I2C interface, which is designed with static CMOS logic. Except for register 10h, which sets the
operating mode, the values in all of the other I2C registers are preserved while entering, during, and leaving
shutdown mode.
Full-Power Mode Without Video Input Detection
and Video Load Detection
This mode is similar to the above mode except that
video input detection and video load detection are not
active. If interrupt is enabled, INT goes active low only
when the slow-switch signal changes.
Standby Mode
In standby mode, the MAX9670/MAX9671 monitor the
slow-switch signals and decide whether to loop through
the audio/video signals. If the VCR slow switch input
has activity (6V or 12V at the input), the audio/video signals are looped through from the VCR SCART to the TV
SCART. If the TV slow-switch input has activity, the
audio/video signals are looped through from the TV
SCART to the VCR SCART. If neither the VCR slowswitch input nor the TV slow switch input show activity,
i.e., both inputs are at ground, no signals are looped
through. If both the VCR slow-switch input and the TV
slow-switch input have activity, the MAX9670/MAX9671
The quiescent power consumption and average power
consumption of the MAX9670/MAX9671 are very low
because of 3.3V operation and low-power circuit design.
Quiescent power consumption is defined when the
MAX9670/MAX9671 are operating without loads and
without any audio or video signals. Table 7 shows the
quiescent power consumption in all 4 operating modes.
Average power consumption is defined when the
MAX9670/MAX9671 drives typical signals into typical
loads. Table 6 shows the average power consumption
in full-power mode and Table 9 shows the input and
output conditions.
22
Power Consumption
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
TV_SS ACTIVE
VCR_SS ACTIVE
TV_SS NOT ACTIVE
VCR_SS NOT ACTIVE
STATE 0
SEARCH
AUDIO: INACTIVE
VIDEO: INACTIVE
SLOW SWITCH: LISTENING FOR ACTIVITY
FAST SWITCH: INACTIVE
TV_SS ACTIVE
VCR_SS NOT ACTIVE
TV_SS NOT ACTIVE
VCR_SS ACTIVE
TV_SS NOT ACTIVE
VCR_SS NOT ACTIVE
TV_SS NOT ACTIVE
VCR_SS NOT ACTIVE
TV_SS ACTIVE
VCR_SS NOT ACTIVE
TV_SS NOT ACTIVE
VCR_SS ACTIVE
STATE 1
TV-TO-VCR
STATE 2
VCR-TO-TV
AUDIO: TV TO VCR
VIDEO: TV TO VCR
SLOW SWITCH: TV TO VCR
FAST SWITCH: NOT APPLICABLE
AUDIO: VCR TO TV
VIDEO: VCR TO TV
SLOW SWITCH: VCR TO TV
FAST SWITCH: VCR TO TV
TV_SS ACTIVE
VCR_SS ACTIVE
TV_SS ACTIVE
VCR_SS ACTIVE
TV_SS NOT ACTIVE
VCR_SS ACTIVE
TV_SS ACTIVE
VCR_SS NOT ACTIVE
Figure 14. Standby mode finite state machine. TV_SS is active when either 6V or 12V are present. VCR_SS is active when either 6V
or 12V are present.
S-Video
The MAX9670/MAX9671 support S-video from the settop box to the TV, set-top box to the VCR, and VCR to
the set-top box. S-video was not included in the original
SCART specifications but was added afterwards. As a
consequence, the luma (Y) signal of S-video shares the
same SCART pin as the CVBS signal. Likewise, the
chroma (C) signal shares the same SCART pin as the
red signal. The pins that can carry both CVBS and luma
have Y/CVBS in their names, and the pins that can
carry red and chroma have R/C in their names.
Now, the Y/CVBS signals are full duplex while the R/C
signals are half duplex. Therefore, S-video is limited to
being half duplex. The MAX9670/MAX9671 have to
transmit a chroma signal and receive a chroma signal
______________________________________________________________________________________
23
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
0.1µF
VCR_R/C_IN
ENC_R/C_IN
ENC_C_IN
BIAS
AV = 2V/V
BIAS
LPF
BIAS
LPF
AV = 2V/V
TV_R/C_OUT
75Ω
VCR_R/C_OUT
75Ω
MAX9670/MAX9671
TV
SCART
VCR
SCART
ON
Figure 15. Gain-of-2 amplifier on VCR_R/C_OUT outputs chroma signal to VCR SCART connector. Notice that the pulldown switch on
VCR_R/C_OUT is open.
0.1µF
VCR_R/C_IN
ENC_R/C_IN
ENC_C_IN
BIAS
AV = 2V/V
BIAS
LPF
BIAS
LPF
AV = 2V/V
TV_R/C_OUT
75Ω
VCR_R/C_OUT
75Ω
MAX9670/MAX9671
TV
SCART
VCR
SCART
OFF
Figure 16. VCR_R/C_IN receives chroma signal from VCR SCART connector. Notice that the pulldown switch on VCR_R/C_OUT is
closed and that the gain-of-2 amplifier is off. The chroma signal from VCR SCART is looped through to the TV SCART in the above
configuration.
on the same SCART pin, but not at the same time. The
75Ω resistor connected to VCR_R/C_OUT must act as a
back termination resistor when the MAX9670/MAX9671
is transmitting chroma signal and as an input termination resistor when it is receiving a chroma signal. Figure
15 shows how the MAX9670/MAX9671 transmits a
chroma signal to the VCR SCART connector while
Figure 16 shows how the MAX9670/MAX9671 receives
a chroma from the VCR SCART connector.
24
Write a 0 into bit 2 of register 09h to open the pulldown
switch at VCR_R/C_OUT. To close the pulldown switch,
write a 0 into bit 6 of register 0Dh to turn off the output
amplifier, and then write a 1 into register 09h. See
Tables 17 and 18.
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
TV_OUTR
10kΩ
MAX9670/MAX9671
MONO AUDIO
10kΩ
TV_OUTL
75Ω
TV
SCART
TV_Y/CVBS_OUT
75Ω OR GREATER
75Ω OR GREATER
RF
MODULATOR
Figure 17. Application Circuit to Connect CVBS and Mono Audio from TV SCART to RF Modulator
Interfacing to an RF Modulator
If the set-top box modulates CVBS and mono audio
onto an RF carrier (for example, channel 3), a simple
application circuit can provide the needed signals (see
Figure 17). 10kΩ resistor summer circuit between
TV_OUTR and TV_OUTL creates the mono audio signal. The resistor-divider to ground on TV_Y/CVBS_OUT
creates a video signal with normal amplitude. The
unique feature of the MAX9670/MAX9671 that facilitates
this application circuit is that the audio and video output amplifiers of the MAX9670/MAX9671 can drive multiple loads if V AUD and V VID are both greater than
3.135V.
Floating-Chassis Discharge Protection
and ESD
Some set-top boxes have a floating chassis problem in
which the chassis is not connected to earth ground. As
a result, the chassis can charge up to 500V. When a
SCART cable is connected to the SCART connector,
the charged chassis can discharge through a signal
pin. The equivalent circuit is a 2200pF capacitor
charged to 311V connected through less than 0.1Ω to a
signal pin. The MAX9670/MAX9671 are soldered on the
PCB when it experiences such a discharge. Therefore,
the current spike flows through both external and internal ESD protection devices and is absorbed by the
supply bypass capacitors, which have high capacitance and low ESR.
To better protect the MAX9670/MAX9671 against
excess voltages during the cable discharge condition
or ESD events, add series resistors to all inputs and
outputs to the SCART connector if series resistors are
not already present in the application circuit. Also, add
external ESD protection diodes (for example, BAV99)
on all inputs and outputs to the SCART connector.
SCART Set-Top Box
with Analog HD Outputs
In set-top boxes with SCART connectors and cinch
connectors for high-definition YPbPr outputs, a triplevideo DAC usually outputs either standard-definition
RGB signals that are routed to the MAX9670/MAX9671
or high-definition YPbPr signals that are routed through
a high-definition filter amplifier like the MAX9653 (see
Figure 19). The set-top box devices have a limited number of video DACs, and hence, one bank of triple-video
DACs switches video format depending upon whether
standard-definition RGB or high-definition YPbPr signals are required.
When RGB signals are desired, the high-definition filter
amplifier should be turned off so that the RGB signals
do not appear on the YPbPr connectors. The
MAX9653/MAX9654 are well-suited for this application
because their video inputs are in high-impedance
mode when in shutdown.
______________________________________________________________________________________
25
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
12V
3.3V
0.1µF
V12
3.3V
0.1µF
VVID
0.1µF
VAUD
VAUD
TV_INL
(MAX9671 ONLY)
+3.3 V
TV_INR
(MAX9671 ONLY)
STB CHIP
VAUD CPVSS
2.55kΩ
7.68kΩ
1µF
CPVSS VAUD
2.55kΩ
75Ω
SDA
MICROCONTROLLER
1µF
7.68kΩ
TV_OUTR
VAUD
SCL
75Ω
INT
CPVSS
TV_OUTL
V12
DEV_ADDR
75Ω
CPVSS
TV_SS
VID
75Ω
TV_B_OUT
VIDEO ENCODER
75Ω
75Ω
75Ω
ENC_R/C_IN
75Ω
75Ω
75Ω
VVID
75Ω
TV_Y/CVBS_IN
ENC_Y_IN
GNDVID
TV_Y/CVBS_OUT
ENC_B_IN
75Ω
GNDVID
VID
TVOUT_FS
ENC_G_IN
75Ω
GNDVID
VID
TV_R/C_OUT
75Ω
75Ω
GNDVID
VID
TV_G_OUT
75Ω
75Ω
VID
75Ω
ENC_Y/CVBS_IN
TV
SCART
EP
0.1µF
75Ω
MAX9670
MAX9671
75Ω
VAUD
GNDVID
75Ω
GNDVID
ENC_C_IN
GNDVID
75Ω
VCR_OUTR
75Ω
VAUD
7.68kΩ
CPVSS
1µF
VCR_INR
STEREO
AUDIO DACS
1µF
CPVSS
2.55kΩ
75Ω
6.65kΩ
VCR_OUTL
ENC_INL
VAUD
7.68kΩ
CPVSS
1µF
VCR_INL
R1*
1µF
VAUD
CPVSS
2.55kΩ
75Ω
6.65kΩ
V12
VCR
SCART
VCR_SS
ENC_INR
VVID
0.1µF
75Ω
R1*
EP
VCR_B_IN
75Ω
GNDVID VVID
0.1µF
75Ω
VCR_G_IN
75Ω
75Ω
VVID GNDVID
0.1µF
VCR_R/C_IN
VVID
GNDVID
VCR_R/C_OUT
*R1 VALUES
DAC = CS4334/5/8/9: R1 = 4.53kΩ ±1%
DAC = PCM1742: R1 = 5.57kΩ ±1%
VVID
75Ω
GNDVID
VCRIN_FS
VVID
75Ω
GNDVID
VCR_Y/CVBS_OUT
75Ω
VVID
GNDVID
0.1µF
C1P
EP
VCR_Y/CVBS_IN
C1N CPVSS
75Ω
1µF
GNDVID
75Ω
1µF
Figure 18. Application Circuit to Connect Series Resistors and External ESD Protection Diodes at MAX9670/MAX9671 Outputs
26
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
ENC_R/C_IN
3.3V
0.1µF
75Ω
0.1µF
75Ω
SCART
CONNECTOR
3.3V
75Ω
75Ω
TV_G_OUT
ENC_G_IN
0.1µF
SET-TOP BOX
CHIP
TV_B_OUT
ENC_B_IN
MAX9670/MAX9671
ENC_R/C_IN TV_R/C_OUT
TV_G_OUT
ENC_G_IN
0.1µF
SET-TOP BOX
CHIP
75Ω
TV_R/C_OUT
TV_B_OUT
ENC_B_IN
INPUTS SET TO SYNC-TIP CLAMP
SCART
CONNECTOR
75Ω
INPUTS SET TO HIGH IMPEDANCE
DAC
DAC
3.3V
3.3V
DAC
DAC
3.3V
3.3V
DAC
DAC
MAX9653
MAX9654
YOUT
YIN
YPbPr OUTPUTS
75Ω
PRIN
75Ω
YIN
YOUT
PBIN
PBOUT
PRIN
PROUT
0.1µF
75Ω
PBOUT
PBIN
MAX9653
MAX9654
0.1µF
75Ω
0.1µF
PROUT
ON
OFF
(A)
YPbPr OUTPUTS
75Ω
SHDN
3.3V
SHDN
75Ω
(B)
Figure 19. Triple DAC is connected to both a MAX9670 and a MAX9653/MAX9654 high-definition video-filter amplifier. (A) The
MAX9670/MAX9671 are transmitting standard-definition RGB signals while the MAX9653/MAX9654 are in shutdown mode. (B) The
MAX9670/MAX9671 are not transmitting RGB signals, but the MAX9653/MAX9654 are transmitting high-definition YPbPr signals.
Similarly, when YPbPr signals are desired, ENC_R/C_IN,
ENC_G_IN, and ENC_B_IN of the MAX9670/MAX9671
should be set to high-impedance mode by setting bit 4 in
register 08h to high if those video inputs are AC-coupled.
The high-impedance mode has higher priority whether
ENC_R/C_IN is in sync-tip clamp or bias circuit mode
(set by bit 3 in register 08h). If ENC_R/C_IN, ENC_G_IN,
and ENC_B_IN are DC-coupled, the inputs should be left
in sync-tip clamp mode. The RGB outputs of the
MAX9670 should be muted or shut down.
In either case, the inactive device should not distort the
video signals generated by the DACs.
Power-Supply Bypassing
The MAX9670/MAX9671 feature single 3.3V and 12V
supply operation and require no negative supply. The
12V supply V12 is for the SCART switching function. For
V12, place a 0.1µF bypass capacitor as close as possible. Connect all VAUD pins together to 3.3V and bypass
with a 10µF electrolytic capacitor in parallel with a
0.1µF ceramic capacitor to audio ground. Bypass each
VVID to video ground with a 0.1µF ceramic capacitor.
Using a Digital Supply
The MAX9670/MAX9671 are designed to operate from
noisy digital supplies. The high PSRR (49dB at 100kHz)
allows the MAX9670/MAX9671 to reject the noise from
the digital power supplies (see the Typical Operating
Characteristics). If the digital power supply is very noisy
and stripes appear on the television screen, increase
the supply bypass capacitance. An additional, smaller
capacitor in parallel with the main bypass capacitor
can reduce digital supply noise because the smaller
capacitor has lower equivalent series resistance (ESR)
and equivalent series inductance (ESL).
Layout and Grounding
For optimal performance, use controlled-impedance
traces for video signal paths and place input termination resistors and output back-termination resistors
close to the MAX9670/MAX9671. Avoid routing video
traces parallel to high-speed data lines.
The MAX9670/MAX9671 provide separate ground connections for video and audio supplies. For best performance, use separate ground planes for each of the
ground returns and connect all ground planes together
at a single point. See the MAX9670/MAX9671 evaluation kit for a proven circuit board layout example.
If the MAX9670/MAX9671 are mounted using flow soldering or wave soldering, the ground via(s) for the EP
pad should have a finished hole size of at least 14mils
to insure adequate wicking of soldering onto the
exposed pad. If the MAX9670/MAX9671 are mounted
using solder mask technique, the via requirement does
not apply. In either case, a good connection between
the exposed pad and ground is required to minimize
noise from coupling onto the outputs.
______________________________________________________________________________________
27
MAX9670/MAX9671
MAX9670/MAX9671
0.1µF
0.1µF
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Table 1. Recommended Coupling for Incoming Video Signals and Input Circuit
Configuration*
VIDEO ORIGIN
FORMAT
VOLTAGE RANGE
COUPLING
INPUT CIRCUIT CONFIGURATION
External
CVBS
Unknown
AC
Transparent sync-tip clamp
External
RGB
Unknown
AC
Transparent sync-tip clamp
External
Y
Unknown
AC
Transparent sync-tip clamp
External
C
Unknown
AC
Bias circuit
Internal
CVBS
0 to 1V
DC
Transparent sync-tip clamp
Internal
R, G, B
0 to 1V
DC
Transparent sync-tip clamp
Internal
Y, C
0 to 1V
DC
Transparent sync-tip clamp
Internal
Y, Pb, Pr
0 to 1V
DC
Transparent sync-tip clamp
Internal
CVBS
2.3V to 3.3V
AC
Transparent sync-tip clamp
Internal
R, G, B
2.3V to 3.3V
AC
Transparent sync-tip clamp
Internal
Y
2.3V to 3.3V
AC
Transparent sync-tip clamp
Internal
C
2.3V to 3.3V
AC
Bias circuit
*Use a 0.1µF capacitor to AC-couple a video signal into the MAX9670/MAX9671.
Table 2. Slow-Switching Modes
SLOW-SWITCHING
SIGNAL VOLTAGE
(V)
0 to 2
28
MODE
Display device uses an internal
source such as a built-in tuner to
provide a video signal.
4.5 to 7.0
Display device uses a video signal
from the SCART connector and sets
the display to 16:9 aspect ratio.
9.5 to 12.6
Display device uses a signal from the
SCART connector and sets the
display to 4:3 aspect ratio.
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
Table 3. Slave Address
DEV_ADDR
B7
B6
B5
B4
B3
B2
B1
B0
GNDVID
VVID
SCL
SDA
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
0
0
1
1
1
1
0
0
0
1
0
1
R/W
R/W
R/W
R/W
Table 4. I2C Register Values in State 0*
WRITE ADDRESS
(hex)
94h
96h
98h
9Ah
READ ADDRESS
(hex)
95h
97h
99h
9Bh
Table 5. I2C Register Values in State 1*
VALUE (binary)
REGISTER ADDRESS
(hexadecimal)
VALUE (binary)
00h
uuuu uuuu
00h
uuuu uuu0
01h
uuuu 1111
01h
uuuu 1011
06h
uuuu uuuu
06h
uuuu uuuu
07h
uuuu uu10
07h
uuu0 0u10
08h
uuuu uuuu
08h
uuuu u011
09h
uuuu u010
09h
uuuu u0MM
0Dh
0000 000u
0Dh
1100 001u
REGISTER ADDRESS
(hexadecimal)
*u indicates that the bit is unchanged from its previous state.
*u indicates that the bit is unchanged from its previous state;
MM = Register 0Eh (bit 0, bit 1)
Table 6. I2C Register Values in State 2*
REGISTER ADDRESS
(hexadecimal)
VALUE (binary)
00h
uuuu uuu0
01h
uuuu 1101
06h
uuu0 1010
07h
uuu0 0uNN
08h
uuuu uuuu
09h
uuuu u110
0Dh
0011 111u
*u indicates that the bit is unchanged from its previous state;
NN = Register 0Eh (bit 3, bit 2)
______________________________________________________________________________________
29
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Table 7. Quiescent Power Consumption
OPERATING MODE
Table 8. Average Power Consumption
POWER CONSUMPTION
(mW)
Shutdown
0.13
Standby mode with no video
activity (i.e., TV slow-switch and
VCR slow-switch inputs are at
ground). Standby mode is the
power-on default.
2.83
Full-power mode with input video
detection and video load
detection active.
66
Full-power mode without input
video detection and video load
detection active.
65
OPERATING MODE
POWER CONSUMPTION
(mW)
Full-power mode with input video
detection and video load
detection active.
300
Full-power mode without input
video detection and video load
detection active.
300
Table 9. Conditions for Average Power Consumption Measurement
30
PIN (MAX9670)
NAME
TYPE
SIGNAL
LOAD
5
VAUD
Supply
3.3V
N/A
9
ENC_INL
Input
0.25VRMS, 1kHz
N/A
10
ENC_INR
Input
0.25VRMS, 1kHz
N/A
11
VCR_INL
Input
None
N/A
12
VCR_INR
Input
None
N/A
13
TV_OUTL
Output
1VRMS, 1kHz
10kΩ to ground
14
VCR_OUTL
Output
1VRMS, 1kHz
10kΩ to ground
15
VCR_OUTR
Output
1VRMS, 1kHz
10kΩ to ground
16
TV_OUTR
Output
1VRMS, 1kHz
10kΩ to ground
17
TV_SS
Output
12V
10kΩ to ground
18
V12
Supply
12V
N/A
19
VCR_SS
Input
0
N/A
20
TVOUT_FS
Output
3.3V
150Ω to ground
21
VCRIN_FS
Input
0
N/A
22
ENC_B_IN
Input
50% flat field
N/A
23
ENC_G_IN
Input
50% flat field
N/A
24
VCR_B_IN
Input
None
N/A
25
VCR_G_IN
Input
None
N/A
26
TV_B_OUT
Output
50% flat field
150Ω to ground
27
TV_G_OUT
Output
50% flat field
150Ω to ground
28
GNDVID
Supply
0
N/A
29
VCR_R/C_IN
Input
None
N/A
30
VVID
Supply
3.3V
N/A
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
Table 9. Conditions for Average Power Consumption Measurement (continued)
PIN (MAX9670)
NAME
TYPE
SIGNAL
31
ENC_C_IN
Input
None
LOAD
N/A
32
ENC_R/C_IN
Input
50% flat field
N/A
33
TV_R/C_OUT
Output
50% flat field
150Ω to ground
34
VCR_R/C_OUT
Output
50% flat field
150Ω to ground
35
VCR_Y/CVBS_OUT
Output
50% flat field
150Ω to ground
36
TV_Y/CVBS_OUT
Output
50% flat field
150Ω to ground
37
VCR_Y/CVBS_IN
Input
None
N/A
38
TV_Y/CVBS_IN
Input
None
N/A
39
ENC_Y_IN
Input
None
N/A
40
ENC_Y/CVBS_IN
Input
50% flat field
N/A
Table 10. Data Format for Write Mode
REGISTER
ADDRESS (hex)
BIT 7
BIT 6
00h
Not used
TV ZCD
01h
Not used
02h
03h
04h
05h
06h
07h
Not used
Not used
08h
VCR_R/C_IN
clamp
BIT 5
Not used
0Ah
0Bh
0Ch
0Dh
10h
VCR_Y/
VCR_R/
CVBS_OUT
C_OUT
enable
enable
Operating mode
BIT 3
TV volume control
Not used
09h
BIT 4
TV_R/
C_OUT
enable
BIT 2
BIT 1
BIT 0
TV audio
output mute
Interrupt
VCR audio selection
TV audio selection
enable
Not used
Not used
Not used
Not used
TV G and B video switch
TV video switch
Set TV fast switching
Not used
Set TV slow switching
ENC R/G/B
ENC_R/C_IN
highVCR video switch
clamp
impedance
bias
VCR_R/C_OUT
Set VCR slow
ground
switching
Not used
Not used
Not used
TV_Y/
TV_G_OUT TV_B_OUT
TVOUT_FS
Not used
CVBS_OUT
enable
enable
enable
enable
Not used
______________________________________________________________________________________
31
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Table 11. Data Format for Read Mode
REGISTER
ADDRESS (hex)
BIT 7
BIT 6
0Eh
Not used
Power-on
reset
0Fh
BIT 5
BIT 4
BIT 3
Not used
BIT 1
VCR slow-switch input
status
Not used
ENC_Y/
CVBS_IN
input video
detection
ENC_Y_IN
input video
detection
BIT 2
TV slow switch input
status
VCR CVBS
input video
detection
VCR CVBS
output load
BIT 0
TV CVBS
output load
TV CVBS
input video
detection
Table 12. Register 00H: Audio Control
DESCRIPTION
BIT
7
6
5
4
3
2
1
0
TV Audio Mute
1
TV Volume Control
Off
On (power-on default)
0
0
0
0
0
0dB gain (power-on default)
0
0
0
0
1
-2dB gain
0
0
0
1
0
-4dB gain
0
0
0
1
1
-6dB gain
0
0
1
0
0
-8dB gain
0
0
1
0
1
-10dB gain
...
...
...
...
...
...
...
...
...
TV Zero-Crossing Detector
COMMENTS
0
1
1
1
1
0
-60dB gain
1
1
1
1
1
-62dB gain
0
Off
1
On (power-on default)
Table 13. Register 01H: TV Audio
DESCRIPTION
BIT
7
6
5
4
3
2
Input Source for TV Audio
Input Source for VCR Audio
Interrupt Enable
32
1
0
0
0
COMMENTS
Encoder audio
0
1
VCR audio
1
0
TV audio (MAX9671 only)
1
1
Mute (power-on default)
0
0
0
1
Encoder audio
VCR audio
1
0
TV audio (MAX9671 only)
1
1
Mute (power-on default)
0
Disabled (power-on default)
1
Enabled
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
DESCRIPTION
BIT
7
6
5
4
3
Input Sources for TV Video
Input Sources for TV_G_OUT and TV_B_OUT
2
1
COMMENTS
0
TV_Y/CVBS_OUT
TV_R/C_OUT
0
0
0
ENC_Y/CVBS_IN
ENC_R/C_IN
0
0
1
ENC_Y_IN
ENC_C_IN
0
1
0
VCR_Y/CVBS_IN
VCR_R/C_IN
0
1
1
TV_Y/CVBS_IN
1
0
0
Not used
Not used
1
0
1
Mute
Mute
1
1
0
Mute
Mute
1
1
1
Mute (power-on
default)
Mute (power-on
default)
TV_G_OUT
TV_B_OUT
0
0
ENC_G_IN
ENC_B_IN
0
1
VCR_G_IN
VCR_B_IN
1
0
Mute
Mute
1
1
Mute (power-on
default)
Mute (power-on
default)
Table 15. Register 07H: TV Video Output Control
DESCRIPTION
BIT
7
6
5
4
3
Set TV Slow Switching
2
0
0
0
Low (< 2V) internal source
0
1
Medium (4.5V to 7V); external SCART
source with 16:9 aspect ratio
1
0
High impedance (power-on default)
1
High (> 9.5V); external SCART source
with 4:3 aspect ratio
1
Set TV Fast Switching
COMMENTS
1
0
0
0
1
GNDVID (power-on default)
Not used
1
0
Same level as VCR_FB_IN
1
1
VVID
______________________________________________________________________________________
33
MAX9670/MAX9671
Table 14. Register 06H: TV Video Input Control
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Table 16. Register 08H: ENC and VCR Video Input/Output Control
DESCRIPTION
BIT
7
6
5
4
3
Input Sources for VCR Video
ENC_R/C_IN Clamp/Bias
34
1
COMMENTS
0
VCR_Y/CVBS_OUT
VCR_R/C_OUT
0
0
0
ENC_Y/CVBS_IN
ENC_R/C_IN
0
0
1
ENC_Y_IN
ENC_C_IN
0
1
0
VCR_Y/CVBS_IN
VCR_R/C_IN
0
1
1
TV_Y/CVBS_IN
Mute
1
0
0
Not used
Not used
1
0
1
Mute
Mute
1
1
0
Mute
Mute
1
1
1
Mute (power-on
default)
Mute (power-on
default)
0
DC restore clamp active at input
(power-on default)
1
Chrominance bias applied at input
0
High-impedance bias off
(power-on default)
1
Biases the R/C, G, and B inputs to high
impedance (overwrites the ENC_R/C_IN
clamp and bias bit)
ENC R/C, G, and B inputs high-impedance
bias (in HD application)
VCR_R/C_IN Clamp/Bias
2
0
DC restore clamp active at input
(power-on default)
1
Chrominance bias applied at input
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
DESCRIPTION
BIT
7
6
5
4
3
2
Set VCR Function Switching
COMMENTS
1
0
0
0
Low (< 2V) internal source
0
1
Medium (4.5V to 7V); external SCART
source with 16:9 aspect ratio
1
0
High impedance (power-on default)
1
High (> 9.5V); external SCART source
with 4:3 aspect ratio
1
0
Normal operation; pulldown on
VCR_R/C_OUT is off (power-on
default)
1
Ground; pulldown on VCR_R/C_OUT
is on; the output amplifier driving
VCR_R/C_OUT is off
VCR_R/C_OUT Ground
Table 18. Register 0DH: Output Enable
DESCRIPTION
BIT
7
6
5
4
3
2
1
0
TVOUT_FS Enable
1
TV_Y/CVBS_OUT Enable
0
TV_B_OUT Enable
1
0
TV_G_OUT Enable
1
TV_R/C_OUT Enable
0
VCR_R/C_OUT Enable
VCR_Y/CVBS_OUT Enable
1
COMMENTS
0
Off (power-on default)
On
0
Off (power-on default)
1
On
Off (power-on default)
On
Off (power-on default)
On
0
Off (power-on default)
1
On
Off (power-on default)
On
0
Off (power-on default)
1
On
______________________________________________________________________________________
35
MAX9670/MAX9671
Table 17. Register 09H: VCR Video Output Control
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Table 19. Register 10H: Operating Modes
DESCRIPTION
BIT
5
4
3
2
1
COMMENTS
7
6
0
0
0
Shutdown
0
1
Standby mode (power-on default).
Input video detection circuits are
active. Audio circuitry is off unless
video is detected. Once slow switch
is detected, the signal paths between
the VCR and TV SCART are
connected.
1
0
Full-power mode with input video
detection and video-load detection
active.
1
1
Full-power mode without input video
detection and video-load detection
active.
7
6
Operating Mode
Table 20. Register 0EH: Status
DESCRIPTION
BIT
5
4
3
2
TV Slow-Switching Input Status
VCR Slow-Switching Input Status
Power-On Reset
1
36
COMMENTS
1
0
0
0
0 to 2V; internal source
0
1
4.5V to 7V; external source with 16:9
aspect ratio
1
0
Not used
1
1
9.5V to 12.6V; external source with
4:3 aspect ratio
0
0
0 to 2V; internal source
0
1
4.5V to 7V; external source with 16:9
aspect ratio
1
0
Not used
1
1
9.5V to 12.6V; external source with
4:3 aspect ratio
0
VVID is too low for digital logic to
operate
1
VVID is high enough for digital logic to
operate
The temperature is below the thermal
shutdown limit
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
Table 21. Register 0Fh: Video Activity Status
DESCRIPTION
BIT
7
6
5
4
3
2
1
TV CVBS Input Video Detection
0
TV CVBS Output Load
1
VCR CVBS Input Video Detection
0
VCR CVBS Output Load
1
0
ENC_Y/CVBS Input Video Detection
ENC_Y_IN Input Video Detection
1
0
COMMENTS
0
No video detected.
1
Video detected.
No video detected.
Video detected.
0
No video detected.
1
Video detected.
No load connected.
Load connected.
No video detected.
Video detected.
0
No video detected.
1
Video detected.
______________________________________________________________________________________
37
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
MAX9670/MAX9671
Typical Application Circuit
12V
3.3V
3.3V
0.1µF
V12
0.1µF
VVID
0.1µF
VAUD
7.68kΩ
TV_INL
(MAX9671 ONLY)
+3.3 V
2.55kΩ
7.68kΩ
TV_INR
(MAX9671 ONLY)
STB CHIP
2.55kΩ
SDA
MICROCONTROLLER
TV_OUTR
75Ω
SCL
TV_OUTL
INT
75Ω
DEV_ADDR
TV_SS
75Ω
TV_B_OUT
VIDEO ENCODER
TV
SCART
75Ω
TV_G_OUT
ENC_Y/CVBS_IN
75Ω
TV_R/C_OUT
75Ω
75Ω
ENC_R/C_IN
TVOUT_FS
75Ω
75Ω
ENC_G_IN
TV_Y/CVBS_OUT
0.1µF
75Ω
75Ω
TV_Y/CVBS_IN
ENC_B_IN
75Ω
75Ω
ENC_Y_IN
75Ω
MAX9670
MAX9671
GNDVID
VCR_OUTR
ENC_C_IN
75Ω
7.68kΩ
75Ω
1µF
VCR_INR
2.55kΩ
STEREO
AUDIO DACS
VCR_OUTL
1µF
75Ω
7.68kΩ
6.65kΩ
ENC_INL
1µF
VCR_INL
2.55kΩ
R1*
VCR_SS
1µF
0.1µF
6.65kΩ
75Ω
VCR_B_IN
ENC_INR
VCR
SCART
75Ω
0.1µF
R1*
VCR_G_IN
75Ω
0.1µF
VCR_R/C_IN
VCR_R/C_OUT
75Ω
VCRIN_FS
75Ω
*R1 VALUES
DAC = CS4334/5/8/9: R1 = 4.53kΩ ±1%
DAC = PCM1742: R1 = 5.57kΩ ±1%
VCR_Y/CVBS_OUT
0.1µF
C1P
EP
75Ω
VCR_Y/CVBS_IN
C1N CPVSS
1µF
75Ω
1µF
38
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
VVID
VCR_R/C_IN
GNDVID
TV_G_OUT
TV_B_OUT
VCR_G_IN
VCR_B_IN
ENC_G_IN
ENC_B_IN
VCRIN_FS
N.C.
33
32
31
30
29
28
27
26
25
24
23
VCRIN_FS
ENC_B_IN
VCR_B_IN
ENC_G_IN
VCR_G_IN
TV_G_OUT
TV_B_OUT
GNDVID
VCR_R/C_IN
VVID
TOP VIEW
TOP VIEW
30 29 28 27 26 25 24 23 22 21
20 TVOUT_FS
ENC_C_IN 31
ENC_C_IN
34
22
TVOUT_FS
ENC_R/C_IN
35
21
VCR_SS
TV_R/C_OUT
36
20
V12
VCR_R/C_OUT
37
19
TV_SS
VCR_Y/CVBS_OUT
38
18
TV_OUTR
TV _Y/CVBS_OUT
39
17
VCR_OUTR
VCR_Y/CVBS_IN
40
16
VCR_OUTL
TV_Y/CVBS_IN
41
15
TV_OUTL
13 TV_OUTL
ENC_Y_IN
42
14
VCR_INR
ENC_Y_IN 39
12 VCR_INR
ENC_Y/CVBS_IN
43
13
VCR_INL
ENC_Y/CVBS_IN 40
11 VCR_INL
N.C.
44
12
TV_INR
3
4
DEV_ADDR
INT
11
2
TV_INL
1
40 TQFN
10
10
ENC_INR
9
SCL
8
SDA
INT
7
ENC_INL
DEV_ADDR
6
*EP
ENC_INR
SCL
EP* = EXPOSED PAD
5
CPVSS
4
C1P
3
C1N
2
VAUD
1
SDA
*EP
9
TV_Y/CVBS_IN 38
ENC_INL
14 VCR_OUTL
VCR_Y/CVBS_IN 37
MAX9671
8
15 VCR_OUTR
CPVSS
MAX9670
TV_Y/CVBS_OUT 36
7
16 TV_OUTR
VCR _Y/CVBS_OUT 35
C1N
17 TV_SS
VCR_R/C_OUT 34
6
18 V12
C1P
TV_R/C_OUT 33
5
19 VCR_SS
VAUD
ENC_R/C_IN 32
44 TQFN
EP* = EXPOSED PAD
Chip Information
PROCESS: BiCMOS
______________________________________________________________________________________
39
MAX9670/MAX9671
Pin Configurations
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
40 TQFN
T4066+3
21-0141
44 TQFN
T4477+2
21-0144
QFN THIN.EPS
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
40
______________________________________________________________________________________
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
______________________________________________________________________________________
41
MAX9670/MAX9671
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
42 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.

Open as PDF

Similar pages