Keysight N6700 Modular Power System Family N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Legal Notices © Keysight Technologies 2010 - 2015 No part of this document may be photocopied, reproduced, or translated to another language without the prior agreement and written consent of Keysight Technologies as governed by United States and international copyright laws. Warranty The material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Keysight disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Keysight shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. Should Keysight and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control. Manual Editions Manual Part Number: N6700-90001 Edition 8, January 2015 Available in electronic format only. Updates of this manual containing minor corrections may have the same edition date. Revised editions are identified by a new edition date. 2 Certification Keysight Technologies certifies that this product met its published specifications at time of shipment from the factory. Keysight Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institute's calibration facility, and to the calibration facilities of other International Standards Organization members. Technologies Licenses The hardware and or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license. U.S. Government Restricted Rights Software and technical data rights granted to the federal government include only those rights customarily provided to end user customers. Keysight provides this customary commercial license in Software and technical data pursuant to FAR 12.211 (Technical Data) and 12.212 (Computer Software) and, for the Department of Defense, DFARS 252.227-7015 (Technical Data – Commercial Items) and DFARS 227.7202-3 (Rights in Commercial Computer Software or Computer Software Documentation). Declaration of Conformity Declarations of Conformity for this product and for other Keysight products may be downloaded from the Web. Go to http://www.keysight.com/go/conform ity and click on “Declarations of Conformity.” You can then search by product number to find the latest Declaration of Conformity. Regulatory Symbols The CE mark shows that the product complies with all applicable European Directives. The C-Tick mark is a registered trademark of the Australian Communications Authority. This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada. This is the symbol for an Industrial, Scientific and Medical, Group 1 Class A product. The CSA mark is a registered trademark of Intertek-etlsemko Inc. This is the RoHS (Restriction of Hazardous Substances) symbol for electrical and electronic equipment. This symbol indicates separate collection for electrical and electronic equipment mandated under EU law as of August 13, 2005. All electric and electronic equipment are required to be separated from normal waste for disposal (Reference WEEE Directive 2002/96/EC). N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Where to Find More Information This document provides specification and supplemental characteristic information for the following instruments: • Keysight N6731B through N6784A Power Modules • Keysight N6700B through N6705B Mainframes For additional technical details and ordering information for the Keysight N6700 Modular Power System Family, refer to the following: Document Description Keysight N6700 Modular Power System Family: Low-Profile MPS Mainframe for Automated Test Environments The Keysight N6700 Low-Profile Modular Power System (MPS) is a 1U (rack unit) high, multiple-output programmable DC power supply system that enables test system integrators to optimize performance, power and price to match test needs. Go to: http:// literature.cdn.keysight.com/litweb/pdf/5989-1411EN.pdf Keysight N6700 Modular Power System Family: DC Power Analyzer Mainframe for R&D The Keysight N6705 DC Power Analyzer represents an entirely new instrument category for R&D engineers. It provides unrivaled productivity gains when sourcing and measuring DC voltage and current into a DUT. Using the Keysight N6705 DC Power Analyzer, R&D engineers can gain insights into the DUT’s power consumption in minutes, with all sourcing and measuring functions available from the front panel. Go to: http:// literature.cdn.keysight.com/litweb/pdf/5989-6319EN.pdf Keysight N6700 Modular Power System Family: N6780 Series Source/Measure Units The Keysight N6781A/82A/85A/86A 2-quadrant SMUs offer advanced sourcing and measurement capabilities required to overcome test challenges associated with optimizing power consumption and maximizing battery life of batterypowered devices and their components. The Keysight N6784A 4-quadrant SMU offers advanced sourcing and measurement capabilities in four quadrants for general purpose applications. Go to: http:// literature.cdn.keysight.com/litweb/pdf/5990-5829EN.pdf Keysight N6700 Modular Power System Family: Battery Charge/Discharge Module The Keysight N6783A-BAT battery charge/discharge module is a basic, 2-quadrant DC power module designed to be used by mobile device designers. Its 2-quadrant operation allows it to act as a programmable power supply to charge the battery or as a programmable electronic load to discharge the battery, all in one instrument. Go to: http:// literature.cdn.keysight.com/litweb/pdf/5990-8662EN.pdf Keysight N6700 Modular Power System Family: Mobile Communications DC Power Module The Keysight N6783A-MFG mobile communications DC power module offers advanced features specifically for testing battery-powered (mobile) devices in manufacturing or automated test environments. Go to: http:// literature.cdn.keysight.com/litweb/pdf/5990-8643EN.pdf NOTE You can contact Keysight Technologies at one of the following telephone numbers for warranty, service, or technical support information. In the United States: (800) 829-4444 In Europe: 31 20 547 2111 In Japan: 0120-421-345 Or use our Web link for information on contacting Keysight in your country or specific location: www.keysight.com/find/assist Or contact your Keysight Technologies Representative. The web contains the most up to date version of this manual. Go to http:// literature.cdn.keysight.com/litweb/pdf/N6700-90001.pdf. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 3 Contents 1 - Power Module Differences ................................................................................. 5 Power Module Differences–for Keysight N6700 Modular Power System ....................................................................................................... 6 Power Module Differences–for Keysight N6705 DC Power Analyzer ..................................................................................................... 8 Power Module Option Characteristics ............................................... 10 2 - Keysight N673xB, N674xB, N677xA DC Power Modules ................................. 11 Performance Specifications ................................................................. 12 Supplemental Characteristics ............................................................. 14 Output Quadrant Characteristic.......................................................... 17 Arbitrary Waveform Generator Maximum Bandwidth ..................... 17 3 - Keysight N675xA High Performance Power Modules ....................................... 19 Performance Specifications ................................................................. 20 Supplemental Characteristics ............................................................. 21 Autoranging Characteristic .................................................................. 23 Output Impedance Graphs................................................................... 23 Arbitrary Waveform Generator Maximum Bandwidth ..................... 26 4 - Keysight N676xA Precision Power Modules ..................................................... 27 Performance Specifications ................................................................. 28 Supplemental Characteristics ............................................................. 29 Autoranging Characteristic .................................................................. 31 Output Impedance Graphs................................................................... 31 Arbitrary Waveform Generator Maximum Bandwidth ..................... 33 5 - Keysight N678xA Source/Measure Units.......................................................... 35 Performance Specifications ................................................................. 36 Supplemental Characteristics ............................................................. 38 Output Quadrant Characteristic.......................................................... 43 Output Impedance Graphs................................................................... 44 Voltage Programming Response ........................................................ 46 Measurement Accuracy and Resolution ............................................ 48 6 - Keysight N6783A-BAT, N6783A-MFG Application-Specific Power Modules ... 49 Performance Specifications ................................................................. 50 Supplemental Characteristics ............................................................. 51 Output Quadrant Characteristic.......................................................... 52 7 - Keysight N6700 Modular Power System Mainframes ....................................... 53 Supplemental Characteristics ............................................................. 54 Outline Diagrams ................................................................................... 56 4 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 1 Power Module Differences Power Module Differences–for Keysight N6700 Modular Power System ....................................................................................................... 6 Power Module Differences–for Keysight N6705 DC Power Analyzer ..................................................................................................... 8 Power Module Option Characteristics ............................................... 10 This chapter provides a brief overview of the basic differences between the Keysight N6700 series DC Power Modules. Note that the basic capabilities of a power module depend not only on its hardware capabilities, but also the on the hardware and firmware capabilities of the mainframe in which it is installed. In addition to their primary output and measurement capabilities, power modules installed in a Keysight N6705 DC Power Analyzer have expanded capabilities such as front panel scope view, arbitrary waveform generation, and internal and external data logging. Refer to the Keysight N6700 or N6705 User’s Guide for more information about the power module capabilities. 5 Power Module Differences–for Keysight N6700 Modular Power Systems Keysight N6731B–N6777A Differences Feature DC Power High-Performance Precision (● = available) N673xB, N674xB, N677xA N675xA N676xA 50 W output rating N6731B – N6736B N6751A N6761A 100 W output rating N6741B – N6746B N6752A N6762A 300 W output rating N6773A – N6777A N6753A, N6754A N6763A, N6764A N6755A, N6756A N6765A, N6766A 500 W output rating Output disconnect relays Option 761 Option 761 Option 761 Output disconnect/polarity reversal relays Option 760 Option 760 Option 760 ● ● NOTE 1 Autoranging output capability Voltage or current turn-on priority N6761A, N6762A ● Precision voltage and current measurements Low voltage and low current output range N6761A, N6762A ● Low voltage and low current measurement range 200 microampere measurement range NOTE 2 Option 2UA ● Simultaneous voltage and current measurements SCPI command output list capability NOTE 3 Option 054 Option 054 ● SCPI command array readback NOTE 3 Option 054 Option 054 ● SCPI command programmable sample rate Option 054 Option 054 ● Option 054 Option 054 ● N6753A – N6756A N6763A – N6766A NOTE 3 SCPI command external data logging NOTE 3 Double-wide (occupies 2 channel locations) Option 760 limits the output current to 10A maximum on Models N6742B and N6773A. 1 Option 760 is not available on Models N6741B, N6751A, N6752A, N6761A, and N6762A. 2 Option 2UA.is only available on Models N6761A and N6762A. It includes Option 761. 3 Only available when using the remote interfaces; not from the front panel. 6 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Keysight N6781A–N6786A Differences Feature (● = available) N6781A Output rating 20 W ● 2-quadrant operation Source/Measure Units (SMU) Application-Specific N6782A N6784A N6783A BAT N6783A MFG 24 W ● 18 W ● 20 W ● 20 W N6785A N6786A 80 W ● 80 W ● ● 4-quadrant operation Auxiliary voltage measurement input ● ● Output disconnect relays ● ● ● ● ● Negative voltage protection ● ● ● ● ● Voltage or current priority mode ● ● ● ● ● Programmable output resistance ● Multiple voltage output ranges 3 3 3 4 4 4 4 3 ● 3 ● ● Multiple current output ranges 3 3 4 Multiple voltage measurement ranges 3 3 3 Multiple current measurement ranges Simultaneous voltage and current measurements 4 ● 4 ● 4 ● Seamless measurement autoranging ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● SCPI command output list capability SCPI command array readback NOTE 1, 2 NOTE 2 SCPI command programmable sample rate SCPI command external data logging NOTE 2 NOTE 2 Double-wide (occupies 2 channel locations) 1 List capability is not available on the negative current output on Model N6783A. 2 Only available when using the remote interfaces; not the front panel. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Option 761 Option 761 ● ● 2 2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 7 Power Module Differences–for Keysight N6705 DC Power Analyzers Keysight N6731B–N6777A Differences Feature DC Power High-Performance Precision (● = available) N673xB, N674xB, N677xA N675xA N676xA 50 W output rating N6731B – N6736B N6751A N6761A 100 W output rating N6741B – N6746B N6752A N6762A 300 W output rating N6773A – N6777A N6753A, N6754A N6763A, N6764A N6755A, N6756A N6765A, N6766A 500 W output rating Output disconnect relays Option 761 Option 761 Option 761 Output disconnect/polarity reversal relays NOTE 1 Option 760 ● Option 760 ● Option 760 ● ● ● Arbitrary waveform generation Autoranging output capability Voltage or current turn-on priority N6761A, N6762A ● Precision voltage and current measurements Low voltage and low current output range N6761A, N6762A ● Low voltage and low current measurement range 200 microampere measurement range NOTE 2 Option 2UA ● Voltage or current scope traces ● ● Simultaneous voltage and current scope traces ● Simultaneous voltage and current data logging NOTE 3 ● Interleaved voltage and current data logging NOTE 3 ● ● Dynamic current correction ● N6751A, N6752A N6761A, N6762A SCPI command output list capability NOTE 4 ● ● ● SCPI command array readback ● ● ● ● ● ● NOTE 4 SCPI command programmable sample rate SCPI command external data logging NOTE 4 NOTE 4 ● Double-wide (occupies 2 channel locations) ● ● N6753A – N6756A N6763A – N6766A Option 760 limits the output current to 10A maximum on Models N6742B and N6773A. 1 Option 760 is not available on Models N6741B, N6751A, N6752A, N6761A, and N6762A. 2 Option 2UA is only available on Models N6761A and N6762A. It includes Option 761. 3 Option 055 deletes the Data Logger function on Model N6705. 4 Only available when using the remote interfaces; not from the front panel. 8 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Keysight N6781A–N6786A Differences Feature (● = available) N6781A Output rating 20 W ● 2-quadrant operation Source/Measure Units (SMU) Application-Specific N6782A N6784A N6783A BAT N6783A MFG 24 W ● 18 W ● 20 W ● 20 W N6785A N6786A 80 W ● 80 W ● ● 4-quadrant operation Auxiliary voltage measurement input ● ● Output disconnect relays ● ● ● ● ● ● ● ● ● ● Negative voltage protection ● ● ● ● ● Voltage or current priority mode ● ● ● ● ● CC load/CV load ● ● ● ● ● Voltage/current measurement only ● ● ● ● ● Battery emulator/charger ● ● Programmable output resistance ● ● Multiple voltage output ranges 3 3 3 4 4 Multiple current output ranges 3 3 4 4 4 Arbitrary waveform generation NOTE 1 Option 761 Option 761 ● ● ● ● Multiple voltage measurement ranges 3 3 3 Multiple current measurement ranges 4 4 4 3 3 2 2 Voltage or current scope traces ● ● ● ● ● ● ● Simultaneous voltage and current measurements ● ● ● ● ● Simultaneous voltage and current data logging NOTE 2 ● ● ● ● ● ● ● ● ● Interleaved voltage and current data logging NOTE 2 Seamless measurement autoranging ● ● SCPI command output list capability NOTE 1, 3 ● ● ● ● ● ● ● ● ● ● ● ● ● ● SCPI command programmable sample rate NOTE 3 ● ● ● ● ● ● ● SCPI command external data logging NOTE 3 ● ● ● ● ● ● ● SCPI command histogram measurements ● ● ● ● ● ● SCPI command array readback NOTE 3 NOTE 3 Double-wide (occupies 2 channel locations) 1 Arbitrary waveform generation and list capability are not available on the negative current output on Model N6783A. 2 Option 055 deletes the Data Logger function on Model N6705. 3 Only available when using the remote interfaces; not the front panel. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 9 Power Module Option Characteristics Option 760 & 761 Option 761 provides output and sense disconnect relays. Option 760 provides polarity reversal in addition to output and sense disconnect. Note that models N678xA SMU have output and sense disconnect relays built in. • Option 760 limits the output current to 10 A on Models N6742B and N6773A. + sense + rail +S + Option 761 - rail -S - sense • Option 760 is not available on Models N6741B, N6751A, N6752A, N6761A, N6762A, and N6781A – N6786A Although the plus and minus rail of the output power mesh are physically disconnected from the output terminals with options 760 and 761, a small AC network is still connected across the plus and minus output terminals (see figure). Option 054 Option 054 (High-speed Test Extensions) include output list and digitized measurement capability. This option is separately orderable for Models N673xB, N674xB, N677xA, and N675xA when installed in an N6700 MPS mainframes. All other power modules as well as the N6705 DC Power Analyzer mainframes have output list and digitized measurement capability built in. Output list: • Maximum number of steps = 512 • Maximum dwell time in seconds = 262 • Maximum list repetitions = 256 or infinite Digitized measurement: • Maximum measurement points = 524,288 • Maximum sample rate = 97.656 kHz Option 2UA Option 2UA is a 200 microampere measurement range available on Models N6761A and N6762A only. It includes Option 761 relay capability. 10 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 2 Keysight N673xB, N674xB, N677xA DC Power Modules Performance Specifications ................................................................. 12 Supplemental Characteristics ............................................................. 14 Output Quadrant Characteristic.......................................................... 17 Arbitrary Waveform Generator Maximum Bandwidth ..................... 17 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Keysight N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. 11 Performance Specifications (N6731B-N6746B) N6731B/ N6741B N6732B/ N6742B N6733B/ N6743B N6734B/ N6744B N6735B/ N6745B N6736B/ N6746B DC Output Ratings: 0-5V 0-8V 0 - 20 V 0 - 35 V 0 - 60 V 0 - 100 V Current NOTE 1 Voltage 0-10 A/ 0-20 A 0-6.25 A/0-12.5 A 0-2.5 A / 0-5 A 0-1.5 A / 0-3 A 0-0.8 A / 0-1.6 A 0-0.5 A / 0-1 A Power 50 W / 100 W 50 W / 100 W 50 W / 100 W 52.5W / 105W 50 W / 100 W 50 W / 100 W 10 mV / 20 mV 12 mV 14 mV 15 mV 25 mV 30 mV 2 mV 2 mV 3 mV 5 mV 9 mV 18 mV NOTE 2 Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) CV peak-to- peak CV rms Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 5 mV 6 mV 9 mV 11 mV 13 mV / 16 mV 20 mV / 30 mV Current 2 mA 2 mA 2 mA 2 mA 2 mA 2 mA Source Effect (Regulation): Voltage 1 mV 2 mV 2 mV 4 mV 6 mV 10 mV Current 1 mA 1 mA 1 mA 1 mA 1 mA 1 mA Programming Accuracy: (@ 23 °C ±5 °C after a 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.1% + 19 mV 0.1% + 19 mV 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV Current 0.15% + 20 mA 0.15% + 20 mA 0.15% + 20 mA 0.15% + 20 mA 0.15% + 20 mA 0.15% + 10mA Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.1% + 20 mV 0.1% + 20 mV 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV Current 0.15% + 20 mA 0.15% + 10 mA 0.15% + 5 mA 0.15% + 4 mA 0.15% + 4 mA 0.15% + 2 mA Load Transient Recovery Time: (Time to recover to within the settling band following a load change from 50% to 100% and from 100% to 50% of full load.) Voltage settling band Time 12 NOTE 3 NOTE 3 ±0.08 V / 0.1 V ±0.08 V / 0.1 V ± 0.2 V / 0.3 V ± 0.2 V / 0.3 V ± 0.4 V / 0.5 V ± 0.5 V / 1.0 V < 200 µs < 200 µs < 200 µs < 200 µs < 200 µs < 200 µs N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Performance Specifications (N6773A-N6777A) N6773A N6774A N6775A N6776A N6777A 0 - 20 V 0 - 35 V 0 - 60 V 0 - 100 V 0 - 150 V DC Output Ratings: Voltage Current 0 - 8.5 A 0-5A 0-3A 0-2A 300 W 300 W 300 W 300 W 300 W CV peak-to- peak 20 mV 22 mV 35 mV 45 mV 68 mV CV rms 3 mV 5 mV 9 mV 18 mV 27 mV NOTE 1 0 - 15 A Power NOTE 2 Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 13 mV 16 mV 24 mV 45 mV 68 mV Current 6 mA 6 mA 6 mA 6 mA 6 mA Source Effect (Regulation): Voltage 2 mV 4 mV 6 mV 10 mV 15 mV Current 1 mA 1 mA 1 mA 1 mA 1 mA Programming Accuracy: (@ 23 °C ±5 °C after 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV 0.1% +150 mV Current 0.15% + 60 mA 0.15% + 60 mA 0.15% + 60 mA 0.15% + 30 mA 0.15% + 30 mA Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV 0.1% +150 mV Current 0.15% + 15 mA 0.15% + 12 mA 0.15% + 12 mA 0.15% + 6 mA 0.15% + 6 mA Load Transient Recovery Time: (Time to recover to within the settling band following a load change from 50% to 100% and from 100% to 50% of full load.) Voltage settling band ± 0.3 V NOTE 4 ± 0.3 V NOTE 4 ± 0.5 V ± 1.0 V ± 2.0 V < 250 µs < 250 µs < 250 µs < 250 µs < 250 µs Time 1 Output current is derated 1% per °C above 40°C. 2 When relay option 760 is installed on Models N6742B and N6773A, the output current is limited to 10 A. 3 When relay option 760 or 761 is installed, the settling band is ±0.10V/0.125 V. Option 760 is not available on Model N6741B. 4 When relay option 760 or 761 is installed, the settling band is ±0.35 V. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 13 Supplemental Characteristics (N6731B-N6746B) N6731B/ N6741B N6732B/ N6742B N6733B/ N6743B N6734B/ N6744B N6735B/ N6745B N6736B/ N6746B Programming Ranges: Voltage 15 mV – 5 .1 V 15 mV – 8 .16 V 30 mV – 20.4 V 40 mV – 35.7 V 70 mV – 61.2 V 100 mV – 102 V Current 60 mA – 10.2A/ 60 mA – 20.4 A 40 mA –6.375 A/ 40 mA – 12.75 A 10 mA – 2.55 A/ 10 mA – 5.1 A 5 mA – 1.53 A/ 5 mA – 3.06 A 2.5 mA – 0.85 A/ 2.5 m A – 1.7 A 1.5 mA – 0.51A/ 1.5 mA – 1.02 A Programming Resolution: Voltage 3.5 mV 4 mV 7 mV 10 mV 18 mV 28 mV Current 7 mA 4 mA 3 mA 2 mA 1 mA 0.5 mA Voltage 3 mV 4 mV 10 mV 18 mV 30 mV 50 mV Current 10 mA 7 mA 3 mA 2 mA 1 mA 0.5 mA Measurement Resolution: Programming Temperature Coefficient per °C: Voltage 0.005% +0.1mV 0.005% + 0.1 mV 0.005% + 0.2 mV 0.005% + 0.5 mV 0.005% + 0.5 mV 0.005% + 1 mV Current 0.005% + 1 mA 0.005% + 0.5 mA 0.005% + 0.1 mA 0.005% +0.05mA 0.005% +0.02mA 0.005% +0.02mA Measurement Temperature Coefficient per °C: Voltage 0.01% + 0.1mV 0.01% + 0.1 mV 0.01% + 0.2 mV 0.01% + 0.2 mV 0.01% + 0.5 mV 0.01% + 0.5 mV Current 0.01% + 1 mA 0.01% + 0.5 mA 0.01% + 0.1 mA 0.01% + 0.05 mA 0.01% + 0.02 mA 0.01% + 0.02 mA Measurement Small Signal Bandwidth: (– 3 db typical) Voltage 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 10 kHz 10 kHz 10 kHz 10 kHz 10 kHz 10 kHz NOTE 2 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz Correction On NOTE 1 2 kHz 2 kHz 2 kHz 2 kHz 2 kHz 2 kHz Correction On NOTE 1 Current N6705 Mainframe Oscilloscope Measurement Accuracy: (@t 23 °C ±5 °C; accuracy of any individual point in the trace) Voltage 0.1% + 25 mV 0.1% + 30 mV 0.1% + 45 mV 0.1% + 75 mV 0.1% + 130 mV 0.1% + 190 mV Current 0.15% + 70mA 0.15% + 40 mA 0.15% + 20 mA 0.15% + 14 mA 0.15% + 12 mA 0.15% + 7 mA Correction On NOTE 1 0.15% + 50 mA 0.15% + 30 mA 0.15% + 15 mA 0.15% + 10 mA 0.15% + 9 mA 0.15% + 5 mA Up-programming and Down-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion; for voltage setting from 0V to full scale and full scale to 0V) 20 ms 20 ms 20 ms 20 ms 20 ms 20 ms Up-programming and Down-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full-scale value; for voltage setting from 0V to full scale and full scale to 0V) 100 ms 100 ms 100 ms 100 ms 100 ms 100 ms 0.25% + 50mV 0.25% + 50 mV 0.25% + 75 mV 0.25% + 100 mV 0.25% + 200 mV 0.25% + 250 mV With Option. 760 0.25%+600mV 0.25% + 600 mV 0.25% + 350 mV 0.25% + 250 mV 0.25% + 300 mV 0.25% + 300 mV With Option. 761 0.25%+600mV 0.25% + 600 mV 0.25% + 350 mV 0.25% + 250 mV 0.25% + 300 mV 0.25% + 300 mV 7.5 V 10 V 22 V 38.5 V 66 V 110 V Over-voltage Protection: Accuracy Maximum setting Response time 14 50 µs from occurrence of over-voltage condition to start of output shutdown N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6731B/ N6741B N6732B/ N6742B N6733B/ N6743B N6734B/ N6744B N6735B/ N6745B N6736B/ N6746B 4 mA 2 mA 2 mA 2 mA 2 mA Output Ripple and Noise (PARD): CC rms 8 mA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) Rms Peak-to- peak 1 mA 1 mA 1 mA 1 mA 1 mA 1 mA < 15 mA < 10 mA < 10 mA < 10 mA < 10 mA < 10 mA Remote Sense Capability: Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Series and Parallel Operation: Identically rated outputs can be operated directly in parallel or can be connected for straight series operation. Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay 32 ms 32 ms 32 ms 32 ms 32 ms 32 ms With Option 760 58 ms 58 ms 58 ms 58 ms 58 ms 58 ms 1 Correction On compensates for current flowing into the output capacitor during voltage transients. 2 Stated values apply when the load resistance is at or close to zero. To determine the frequency for larger resistance valuess, refer to the User’s Guide under “Measurement System Bandwidth”. Supplemental Characteristics (N6773A-N6777A) N6773A N6774A N6775A N6776A N6777A Programming Ranges: Voltage 30 mV – 20.4 V 40 mV – 35.7 V 70 mV – 61.2 V 100 mV– 102 V 145 mV –153 V Current 30 mA – 15.3 A 15 mA – 8.67 A 7.5 mA – 5.1 A 4.5 mA– 3.06 A 2.75mA–2.04 A Voltage 7 mV 10 mV 18 mV 28 mV 43 mV Current 9 mA 6 mA 3 mA 1.5 mA 1 mA Voltage 10 mV 18 mV 30 mV 50 mV 77 mV Current 9 mA 6 mA 3 mA 1.5 mA 1 mA Programming Resolution: Measurement Resolution: Programming Temperature Coefficient per °C: Voltage 0.01% + 0.2 mV 0.01% + 0.5 mV 0.01% + 0.5 mV 0.01% + 1 mV 0.01% + 1 mV Current 0.01% + 0.5 mA 0.01% + 0.5 mA 0.01% + 0.1 mA 0.01% + 0.1 mA 0.01% + 0.1 mA Measurement Temperature Coefficient per °C: Voltage 0.01% + 0.2 mV 0.01% + 0.2 mV 0.01% + 0.5 mV 0.01% + 0.5 mV 0.01% + 0.5 mV Current 0.01% + 0.5 mA 0.01% + 0.5 mA 0.01% + 0.05 mA 0.01% + 0.05 mA 0.01% + 0.05 mA Measurement Small Signal Bandwidth: (– 3 db typical) Voltage Correction On NOTE 1 Current NOTE 2 Correction On NOTE 1 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 10 kHz 10 kHz 10 kHz 10 kHz 10 kHz 10 kHz 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 25 kHz 2 kHz 2 kHz 2 kHz 2 kHz 2 kHz 2 kHz N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 15 Supplemental Characteristics (continued) N6773A N6774A N6775A N6776A N6777A N6705 Mainframe Oscilloscope Measurement Accuracy: (@ 23 °C ±5 °C; accuracy of any individual point in the trace) Voltage 0.1% + 45 mV 0.1% + 75 mV 0.1% + 120 mV 0.1% + 160 mV 0.1% + 175 mV Current 0.15% + 45 mA 0.15% + 27 mA 0.15% + 22 mA 0.15% + 12 mA 0.15% + 12 mA 0.15% + 35 mA 0.15% + 22 mA 0.15% + 19 mA 0.15% + 9 mA 0.15% + 9 mA Correction On NOTE 1 Up-programming and Down-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion; for voltage setting from 0V to full scale and full scale to 0V) 20 ms 20 ms 20 ms 20 ms 20 ms Maximum Up-programming and Down-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full-scale value; for voltage setting from 0V to full scale and full scale to 0V) 100 ms 100 ms 100 ms 100 ms 100 ms 0.25% +100 mV 0.25% + 130 mV 0.25% + 260 mV 0.25% + 650 mV 0.25% + 650 mV With Option. 761 0.25% + 500 mV 0.25% + 350 mV 0.25% + 350 mV 0.25% + 650 mV 0.25% + 650 mV With Option. 760 0.25% + 700 mV 0.25% + 700 mV 0.25% + 400 mV 0.25% + 650 mV 0.25% + 650 mV 22 V 38.5 V 66 V 110 V 165 V Over-voltage Protection: Accuracy Maximum setting Response time 50 µs from occurrence of over-voltage condition to start of output shutdown Output Ripple and Noise (PARD): CC rms 6 mA 6 mA 6 mA 6 mA 6 mA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) Rms Peak-to- peak Remote Sense Capability: Series and Parallel Operation: 2 mA 2 mA 2 mA 2 mA 2 mA < 20 mA < 20 mA < 20 mA < 20 mA < 20 mA Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Identically rated outputs can be operated directly in parallel or can be connected for straight series operation. Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay 32 ms 32 ms 32 ms 32 ms 32 ms With Option 760 58 ms 58 ms 58 ms 58 ms 58 ms 1 Correction On compensates for current flowing into the output capacitor during voltage transients. 2 Stated values apply when the load resistance is at or close to zero. To determine the frequency for larger resistance valuess, refer to the User’s Guide under “Measurement System Bandwidth”. 16 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Output Quadrant Characteristic Voltage maximum power + rated voltage 0 + rated current Current Arbitrary Waveform Generator Maximum Bandwidth NOTE The information in this section only applies when the power modules are installed in a Keysight N6705 DC Power Analyzer. The following tables characterize the maximum bandwidth of the arbitrary waveform generator. The maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. The following definitions apply in the frequency tables: V p-p = Voltage peak-to-peak 3 dB max. = Max. frequency where the voltage drops to 3 dB below its setting 6 dB max. = Max. frequency where the voltage drops to 6 dB below its setting THD 3 dB = The total harmonic distortion at 3 dB max. frequency THD 6 dB = The total harmonic distortion at 6 dB max. frequency Voltage 3 dB max THD 3 dB 6 dB max THD 6 dB N6731B & N6741B 0.1 Vp-p 175 Hz 1.0% 260 Hz 3.0% 0.1 Vp-p 125 Hz 1.0% 175 Hz 3.0% 0.3 Vp-p 75 Hz 6.0% 100 Hz 6.0% 0.5 Vp-p 40 Hz 9.0% 55 Hz 9.0% 5.0 Vp-p 20 Hz 10% 37 Hz 10% N6732B & N6742B 0.1 Vp-p 125 Hz 1.0% 200 Hz 3.0% 0.2 Vp-p 125 Hz 1.0% 180 Hz 3.0% 0.4 Vp-p 75 Hz 6.0% 100 Hz 6.0% 0.8 Vp-p 40 Hz 8.5% 60 Hz 8.5% 8.0 Vp-p 20 Hz 10% 37 Hz 10% N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 17 Arbitrary Waveform Generator Maximum Bandwidth (continued) Voltage 3 dB max THD 3 dB 6 dB max THD 6 dB 3 dB max THD 3 dB N6733B & N6743B 6 dB max THD 6 dB N6773A 0.2 Vp-p 110 Hz 1.0% 190 Hz 3.0% 125 Hz 1.5% 210 Hz 4.0% 0.4 Vp-p 110 Hz 1.0% 160 Hz 3.0% 125 Hz 1.5% 180 Hz 4.0% 1.0 Vp-p 72 Hz 6.0% 95 Hz 6.0% 75 Hz 6.0% 95 Hz 6.0% 2.0 Vp-p 40 Hz 8.0% 55 Hz 8.5% 42 Hz 9.0% 60 Hz 9.0% 20 Vp-p 20 Hz 10% 37 Hz 10% 20 Hz 10% 37 Hz 10% N6734B & N6744B N6774A 0.4 Vp-p 125 Hz 1.0% 200 Hz 1.0% 125 Hz 1.0% 200 Hz 1.0% 0.7 Vp-p 125 Hz 1.0% 175 Hz 3.5% 125 Hz 1.0% 160 Hz 3.0% 1.8 Vp-p 72 Hz 6.0% 100 Hz 6.0% 75 Hz 6.0% 95 Hz 6.0% 3.5 Vp-p 40 Hz 8.0% 55 Hz 8.5% 40 Hz 8.5% 55 Hz 8.5% 35 Vp-p 20 Hz 8.0% 37 Hz 8.5% 20 Hz 10% 37 Hz 10% N6735B & N6745B N6775A 0.6 Vp-p 100 Hz 1.0% 180 Hz 1.0% 120 Hz 1.0% 200 Hz 1.0% 1.2 Vp-p 100 Hz 1.0% 160 Hz 3.0% 120 Hz 1.0% 160 Hz 3.0% 3.0 Vp-p 70 Hz 5.5% 92 Hz 5.5% 70 Hz 5.0% 95 Hz 6.0% 6.0 Vp-p 40 Hz 8.0% 55 Hz 8.0% 40 Hz 8.5% 55 Hz 8.5% 60 Vp-p 20 Hz 8.0% 37 Hz 8.0% 20 Hz 10% 35 Hz 10% N6736B & N6746B N6776A 1.0 Vp-p 90 Hz 1.0% 160 Hz 1.5% 75 Hz 1.0% 160 Hz 1.0% 2.0 Vp-p 90 Hz 1.0% 150 Hz 3.0% 75 Hz 1.0% 150 Hz 3.0% 5.0 Vp-p 62 Hz 4.5% 85 Hz 6.0% 55 Hz 4.0% 75 Hz 6.0% 10 Vp-p 37 Hz 8.0% 50 Hz 8.0% 35 Hz 8.0% 45 Hz 8.0% 100 Vp-p 20 Hz 8.0% 35 Hz 8.0% N/A N/A 35 Hz 8.0% N6777A 1.5 Vp-p 70 Hz 1.0% 150 Hz 1.0% 3.0 Vp-p 55 Hz 5.0% 120 Hz 2.0% 7.5 Vp-p 55 Hz 5.0% 70 Hz 6.0% 15 Vp-p 35 Hz 7.0% 55 Hz 7.0% 150 Vp-p N/A N/A 30 Hz 1.0% 18 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 3 Keysight N675xA High Performance Power Modules Performance Specifications ................................................................. 20 Supplemental Characteristics ............................................................. 21 Autoranging Characteristic .................................................................. 23 Output Impedance Graphs................................................................... 23 Arbitrary Waveform Generator Maximum Bandwidth ..................... 26 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Keysight N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. 19 Performance Specifications N6751A/N6752A N6753A/N6755A N6754A/N6756A 0 - 50 V 0 - 20 V 0 - 60 V 0 - 5 A / 0 - 10 A 0 - 50 A 0 - 20 A / 0 - 17A 50 W / 100 W 300 W / 500 W 300 W / 500 W CV peak-to-peak 4.5 mV 5 mV 6 mV CV rms 0.35 mV 1 mV 1 mV DC Output Ratings: Voltage Current NOTE 1 Power Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 2 mV 2 mV 2 mV Current 2 mA 12 mA 5 mA Voltage 1 mV 0.5 mV 1.2 mV Current 1 mA 5 mA 2 mA Source Effect (Regulation): Programming Accuracy: (@ 23 °C ±5 °C after 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.06% + 19 mV 0.06% + 10 mV 0.06% + 25 mV Current 0.1% + 20 mA 0.1% + 30 mA 0.1% + 12 mA Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.05% + 20 mV 0.05% + 10 mV 0.05% + 25 mV Current 0.1% + 4 mA 0.1% + 30 mA 0.1% + 8 mA Load Transient Recovery Time: (Time to recover to within the settling band following a load change - from 60% to 100% and from 100% to 60% of full load for model N6751A - from 50% to 100% and from 100% to 50% of full load for models N6752A through N6756A.) Voltage settling band Time ± 75 mV NOTE 2 ± 30 mV NOTE 3 ± 90 mV NOTE 4 < 100 µs < 100 µs < 100 µs 1 Output current is derated 1% per °C above 40°C. 2 When relay option 761 is installed on Model N6752A, the settling band is ±125 mV. 3 When relay option 760 or 761 is installed on Model N6753A and N6755A, the settling band is ±200 mV. 4 When relay option 760 or 761 is installed on Model N6754A and N6756A, the settling band is ±350 mV. 20 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6751A / N6752A N6753A / N6755A N6754A / N6756A Voltage 20 mV – 51 V 10 mV – 20.4 V 25 mV- 61.2 V Current 10 mA – 5.1A/10 mA – 10.2A 50 mA – 51 A 20 mA – 20.4 A/20 mA – 17.3A Voltage 3.5 mV 1.5 mV 4.2 mV Current 3.25 mA 16.3 mA 6.5 mA Voltage 1.8 mV 0.8 mV 2.2 mV Current 410 µA 2.05 mA 0.82 mA Programming Ranges: Programming Resolution: Measurement Resolution: Programming Temperature Coefficient per °C: Voltage 18 ppm + 160 µV 35 ppm + 100 µV 35 ppm + 170 µV Current 100 ppm + 45 µA 60 ppm + 500 µA 60 ppm + 200 µA Measurement Temperature Coefficient per °C: Voltage 25 ppm + 35 µV 50 ppm + 85 µV 50 ppm + 100 µV Current 60 ppm + 3 µA 60 ppm + 30 µA 60 ppm + 12 µA 10 kHz 10 kHz Measurement Small Signal Bandwidth: (– 3 db typical) Voltage Correction On 10 kHz NOTE 1 Current NOTE 2 Correction On NOTE 1 10 kHz - - 10 kHz 10 kHz 10 kHz 2 kHz - - N6705 Mainframe Oscilloscope Measurement Accuracy: (@ 23 °C ±5 °C, accuracy of any individual point in the trace) Voltage Current Correction On NOTE 1 0.05% + 32 mV 0.05% + 15 mV 0.05% + 37 mV 0.1% + 8 mA 0.1% + 52 mA 0.1% + 17 mA 0.1% + 14 mA - - Up-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion) Small voltage step Time 0 V to 10 V 0.2 ms 0 V to 6 V/0 V to 10 V 0.4 ms/0.5 ms 0 V to 15 V/0 V to 29 V 0.35 ms/0.7 ms Large voltage step Time 0 V to 50 V 1.5 ms 0 V to 20 V 1.5 ms 0 V to 60 V 2 ms Up-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time 0 V to 10 V 0 V to 6 V/0 V to 10 V 0 V to 15 V/0 V to 29 V 0.5 ms 0.8 ms/1.0 ms 0.8 ms/1.4 ms 0 V to 50 V 0 V to 20 V 0 V to 60 V 4 ms 3 ms 4.2 ms Down-programming Time with no load: (Time from start of voltage change to output voltage < 0.5 V) Small voltage step Time 10 V to 0 V 0.3 ms 6 V to 0 V/10 V to 0 V 0.55 ms/1.0 ms 15 V to 0 V/29 V to 0 V 0.6 ms/1.2 ms Large voltage step Time 50 V to 0 V 1.3 ms 20 V to 0 V 1.8 ms 60 V to 0 V 2.2 ms N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 21 Supplemental Characteristics (continued) N6751A / N6752A N6753A / N6755A N6754A / N6756A Down-programming Settling Time with no load: (Time from start of voltage change to 0.1% of full scale value) Small voltage step Time 10 V to 0 V 0.45 ms 6 V to 0 V/10 V to 0 V 0.8 ms/1.3 ms 15 V to 0 V/29 V to 0 V 0.8 ms/1.5 ms Large voltage step Time 50 V to 0 V 1.4 ms 20 V to 0 V 2 ms 60 V to 0 V 2.3 ms Down-programming Time with Capacitive load: (Time from start of voltage change to output voltage < 0.5 V) Small voltage step Time 10 V to 0 V 2.1 ms 6 V to 0 V/10 V to 0 V 2.2 ms/4.5 ms 15 V to 0 V/29 V to 0 V 2.3 ms/5.5 ms Large voltage step Time 50 V to 0 V 11 ms 20 V to 0 V 8.5 ms 60 V to 0 V 10 ms 1000 µF 4700 µF 680 µF Continuous power 7W 12.5 W 12.5 W Peak current 7A 15 A 6A Accuracy 0.25% + 0.25 V 0.25% + 0.15V 0.25% + 0.3V Accuracy with Option 761 0.25% + 0.25 V 0.25% + 0.45V 0.25% + 0.6V - 0.25% + 0.45V 0.25% + 0.6V 55 V 22 V 66 V Capacitive load NOTE 3 Down-programming Capability: Over-voltage Protection: Accuracy with Option 760 Maximum setting Response time 50 µs from occurrence of over-voltage condition to start of output shutdown Output Ripple and Noise: (PARD) CC rms: 2 mA 10 mA 4 mA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) rms 500 µA 500 µA 750 µA peak-to-peak < 2 mA < 2 mA < 3 mA Remote Sense Capability: Series and Parallel Operation: Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Identically rated outputs can be operated directly in parallel or can be connected for straight series operation.. Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) 1 Without relay option 25 ms 18 ms 18 ms With relay Option 760 51 ms 44 ms 44 ms Correction On compensates for current flowing into the output capacitor during voltage transients. 2 Stated values apply when the load resistance is at or close to zero. To determine the frequency for larger resistance valuess, refer to the User’s Guide under “Measurement System Bandwidth”. 3 Modules can discharge the specified capacitive load from full scale to 0V at a rate of 4 times/second. 22 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Autoranging Characteristic N6751A 50 W Output Voltage Voltage 50 V N6752A 100 W Output Voltage N6753A / N6754A 300 W Output 20 V 60 V 50 V Voltage N6755A / N6756A 500 W Output 20 V 60 V 500 W curve 50 W curve 100 W curve 6V 15 V 12 V Current 8.5 V 10 V 0 1A 5A 0 300 W curve Current 2A Current 0 8.33 A 10 A 10 V 29 V 15 A 5A 50 A 20 A Current 0 25 A 8.33 A 50 A 17 A Output Impedance Graphs Magnitude 4 90 45 2 Phase 1 0 0.5 -45 0.25 -90 PHASE (degrees) IMPEDANCE (ohms) 8 0.125 100 1k 10k FREQUENCY (Hz) 100k Model N6752A, CC Mode, @50V, 2A N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 23 24 Model N6753A and N6755A, CV Mode, @20 V, 15A Model N6753A and N6755A, Option 760, CV Mode, @20 V, 15A Model N6753A and N6755A, CC Mode, @20 V, 15A Model N6753A and N6755A, Option 760, CC Mode, @20 V, 15A N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Model N6754A and N6756A, CV Mode, @60 V, 5A Model N6754A and N6756A, Option 760, CV Mode, @60 V, 5A Model N6754A and N6756A, CC Mode, @60 V, 5A Model N6754A and N6756A, Option 760, CC Mode, @60 V, 5A N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 25 Arbitrary Waveform Generator Maximum Bandwidth NOTE The information in this section only applies when the power modules are installed in a Keysight N6705 DC Power Analyzer. The following tables characterize the maximum bandwidth of the arbitrary waveform generator. The maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. The following definitions apply in the frequency tables: V p-p = Voltage peak-to-peak 3 dB max. = Max. frequency where the voltage drops to 3 dB below its setting THD 3 dB = The total harmonic distortion at 3 dB max. frequency THD < 1.5% = The frequency below which the THD is less than 1.5%. Voltage 3 dB max THD 3 dB THD < 1.5% N6751A & N6752A 0.5 Vp-p 4000 Hz 12% 440 Hz 1.0 Vp-p 2200 Hz 21% 440 Hz 2.5 Vp-p 900 Hz 25% 265 Hz 5.0 Vp-p 500 Hz 27% 160 Hz 50.0 Vp-p 340 Hz 22% 25 Hz N6753A & N6755A 0.2 Vp-p 2300 Hz 10% 1300 Hz 0.4 Vp-p 1500 Hz 15% 800 Hz 1.0 Vp-p 980 Hz 19% 480 Hz 2.0 Vp-p 580 Hz 21% 300 Hz 20.0 Vp-p 400 Hz 12% 32 Hz N6754A & N6756A 26 0.6 Vp-p 2800 Hz 8.0% 1600 Hz 1.2 Vp-p 1400 Hz 15% 800 Hz 3.0 Vp-p 600 Hz 17% 300 Hz 6.0 Vp-p 400 Hz 20% 200 Hz 60.0 Vp-p 344 Hz 12% 30 Hz N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 4 Keysight N676xA Precision Power Modules Performance Specifications ........................................................... 28 Supplemental Characteristics ........................................................ 29 Autoranging Characteristic ............................................................ 31 Output Impedance Graphs............................................................. 31 Arbitrary Waveform Generator Maximum Bandwidth ................... 33 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Keysight N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. 27 Performance Specifications N6761A/N6762A N6763A/N6765A N6764A/N6766A 0 - 50 V 0 - 1.5 A / 0 - 3 A 0 - 20 V 0 - 50 A 0 - 60 V 0 - 20 A / 0 - 17 A 50 W / 100 W 5.5 V; 100 mA 5.5 V; 100 mA 300 W / 500 W 2 V; 1.5 A 300 W / 500 W 6 V; 0.5 A 5 mV 1 mV 6 mV 1 mV DC Ratings: Voltage NOTE 1 Current Power Low programming ranges (V & I) Low measurement ranges (V & I) Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) CV peak-to-peak CV rms 4.5 mV 0.35 mV Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage Current 0.5 mV 30 µA (@ 0 –7 V) 65 µA (@ 7 – 50V) 2 mV 12 mA 2 mV 5 mA 0.5 mV 30 µA 0.5 mV 5 mA 1.2 mV 2 mA 0.03% + 5 mV 0.1% + 15 mA - 0.03% + 12 mV 0.075% + 4 mA - Source Effect (Regulation): Voltage Current Programming Accuracy: (@ 23 °C ±5 °C after 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage, high range 0.016% + 6 mV Voltage, low range 0.016% + 1.5 mV Current, high range 0.04% + 200 µA Current, low range 0.04% + 30 µA (@ 0 –7 V) 0.04% + 55 µA (@ 7 –50 V) Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C) Applies when measuring 4096 data points with a 20.48 μs time interval.) Voltage, high range Voltage, low range Current, high range Current, low range 200 µA current range (Option 2UA) 0.016% + 6 mV 0.016% + 1.5 mV 0.04% + 160 µA 0.03% + 15 µA (@ 0 – 7 V) 0.03% + 55 µA (@ 7 – 50 V) 0.5% + 100 nA 0.03% + 10 mV 0.03% + 1.5 mV 0.1% + 10 mA 0.05% + 1.1 mA NOTE 2 0.03% + 25 mV 0.03% + 5 mV 0.1% + 5 mA 0.05% + 0.75 mA NOTE 2 - - Load Transient Recovery Time: (time to recover to within the settling band following a load change - from 60% to 100% and from 100% to 60% of full load for model N6761A - from 50% to 100% and from 100% to 50% of full load for model N6762A through N6766A) Voltage settling band ± 75 mV ± 30 mV NOTE 3 ± 90 mV NOTE 4 Time < 100 µs < 100 µs < 100 µs 1 Output current is derated 1% per °C above 40°C. Applies when measuring currents that remain within the low range. Due to thermal settling, when transitioning from measuring full-rated output current (the worst case), to measuring the current within the low range, the low range accuracy specification is typically met within 5 seconds after the current has transitioned into the low range. Accuracies within this 5 second settling period are typically 2X the specified accuracy or better. 3 When relay option 760 or 761 is installed on Models N6763Aand N6765A, the settling band is ±200 mV. 4 When relay option 760 or 761 is installed on Models N6764Aand N6766A, the settling band is ±350 mV. 2 28 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6761A / N6762A N6763A / N6765A N6764A / N6766A Voltage, high range 15 mV – 51 V 10 mV – 20.4 V 25 mV- 61.2 V Voltage, low range 12 mV – 5.5 V - - Current, high range 1 mA–1.53 A/1 mA–3.06 A 50 mA – 51 A 20 mA–20.4A/20mA–17.3A Current, low range 0.1 mA – 0.1 A - - 880 µV 1.5 mV 4.2 mV Programming Ranges: NOTE 1 Programming Resolution: Voltage, high range Voltage, low range 90 µV - - Current, high range 60 µA 16.3 mA 6.5 mA Current, low range 2 µA - - 440 µV 250 µV 600 µV Measurement Resolution: Voltage, high range Voltage, low range 44 µV 25 µV 60 µV Current, high range 30 µA 500 µA 250 µA Current, low range 1 µA 20 µA 10 µA 200 µA current range (Option 2UA) 4 nA - - Voltage, high range 18 ppm + 140 µV 23 ppm + 95 µV 23 ppm + 218 µV Voltage, low range 40 ppm + 70 µV - - Current, high range 33 ppm + 10 µA 25ppm + 129 µA 25ppm + 52 µA Current, low range 60 ppm + 1.5 µA - - 23 ppm + 53 µV 23 ppm + 73 µV Programming Temperature Coefficient per °C: Measurement Temperature Coefficient per °C: Voltage, high range 23 ppm + 40 µV Voltage, low range 30 ppm + 40 µV 25 ppm + 53 µV 25 ppm + 73 µV Current, high range 40 ppm + 0.3 µA 25 ppm + 21 µA 25 ppm + 7 µA 50 ppm + 0.3 µA 27 ppm + 21 µA 27 ppm + 7 µA 100 ppm + 3 nA/°C - - 10 kHz 10 kHz 10 kHz 10 kHz - - 10 kHz 10 kHz 10 kHz 2 kHz - - Current, low range Current, 200 µA range (Option 2UA) Measurement Small Signal Bandwidth: (– 3 db typical) Voltage Correction On NOTE 2 Current NOTE 3 Correction On NOTE 2 N6705 Mainframe Oscilloscope Measurement Accuracy: (@ 23 °C ±5 °C, accuracy of any individual point in the trace) Voltage Current, high range Correction On NOTE 2 Current, low range 0.016% + 16 mV 0.03% + 13 mV 0.03% + 32 mV 0.04% + 1 mA 0.1% + 16 mA 0.1% + 8.4 mA 0.04% + 10 mA - - 0.03% + 0.175 mA 0.05% + 6.6 mA 0.05% + 2.6 mA Up-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion) Small voltage step Time Large voltage step Time N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 0 V to 10 V 0.6 ms 0 V to 50 V 2.2 ms 0 V to 6 V/0 V to 10 V 0.4 ms/0.5 ms 0 V to 20 V 1.5 ms 0 V to 15 V/0 V to 29 V 0.35 ms/0.7 ms 0 V to 60 V 2 ms 29 Supplemental Characteristics (continued) N6761A / N6762A N6763A / N6765A N6764A / N6766A Up-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time 0 V to 10 V 0.9 ms 0 V to 50 V 4 ms 0 V to 6 V/0 V to 10 V 0.8 ms/1.0 ms 0 V to 20 V 3 ms 0 V to 15 V/0 V to 29 V 0.8 ms/1.4 ms 0 V to 60 V 4.2 ms Down-programming Time with no load: (time from start of voltage change to output voltage < 0.5 V) Small voltage step Time Large voltage step Time 10 V to 0 V 0.3 ms 50 V to 0 V 1.3 ms 6 V to 0 V/10 V to 0 V 0.55 ms/1.0 ms 20 V to 0 V 1.8 ms 15 V to 0 V/29 V to 0 V 0.6 ms/1.2 ms 60 V to 0 V 2.2 ms Down-programming Settling Time with no load: (time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time 10 V to 0 V 0.45 ms 50 V to 0 V 1.4 ms 6 V to 0 V/10 V to 0 V 0.8 ms/1.3 ms 20 V to 0 V 2 ms 15 V to 0 V/29 V to 0 V 0.8 ms/1.5 ms 60 V to 0 V 2.3 ms Down-programming Time with Capacitive load: (time from start of voltage change to output voltage < 0.5 V) Small voltage step Time Large voltage step Time Capacitive load NOTE 4 10 V to 0 V 4.5 ms 50 V to 0 V 23 ms 6 V to 0 V/10 V to 0 V 2.2 ms/4.5 ms 20 V to 0 V 8.5 ms 15 V to 0 V/29 V to 0 V 2.3 ms/5.5 ms 60 V to 0 V 10 ms 1000 µF 4700 µF 680 µF 7W 3.8 A 12.5 W 15 A 12.5 W 6A 0.25% + 0.25 V 0.25% + 0.25 V 55 V 0.25% + 0.15 V 0.25% + 0.45 V 0.25% + 0.45 V 22 V 0.25% + 0.3 V 0.25% + 0.6 V 0.25% + 0.6 V 66 V Down-programming Capability: Continuous power Peak current Over-voltage Protection: Accuracy With Option 761 With Option 760 Maximum setting Response time 50 µs from occurrence of over-voltage condition to start of output shutdown Output Ripple and Noise: (PARD) CC rms: 2 mA 10 mA 4 mA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) rms peak-to-peak Remote Sense Capability: Series and Parallel Operation: 500 µA 500 µA 750 µA < 2 mA < 2 mA < 3 mA Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Identically rated outputs can be operated directly in parallel or can be connected for straight series operation. Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay option 32 ms NOTE 5 18 ms 18 ms With relay Option 760 58 ms NOTE 5 44 ms 44 ms If you are operating the unit below 255 µA in constant current mode, the output may become unregulated with the following load conditions: The load resistance is <175 mΩ and the load inductance is >20 µH. If this occurs, an UNRegulated flag will be generated and the output current may rise above the programmed value but will remain < 255 µA. 2 Correction On compensates for current flowing into the output capacitor during voltage transients 3 Stated values apply when the load resistance is at or close to zero. To determine the frequency for larger resistance valuess, refer to the User’s Guide under “Measurement System Bandwidth”. 4 Modules can discharge the specified capacitive load from full scale to 0V at a rate of 4 times/second. 5 In Current priority mode, minimum delay is 23 ms without relays and 45 ms with relay Option 760. 1 30 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Autoranging Characteristic Output Impedance Graphs Model N6763A and N6765A, CV Mode, @20 V, 15A N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Model N6763A and N6765A, Option 760, CV Mode, @20 V, 15A 31 32 Model N6763A and N6765A, CC Mode, @20 V, 15A Model N6763A and N6765A, Option 760, CC Mode, @20 V, 15A Model N6764A and N6766A, CV Mode, @60 V, 5A Model N6764A and N6766A, Option 760, CV Mode, @60 V, 5A Model N6764A and N6766A, CC Mode, @60 V, 5A Model N6764A and N6766A, Option 760, CC Mode, @60 V, 5A N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Arbitrary Waveform Generator Maximum Bandwidth NOTE The information in this section only applies when the power modules are installed in a Keysight N6705 DC Power Analyzer. The following tables characterize the maximum bandwidth of the arbitrary waveform generator. The maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. The following definitions apply in the frequency tables: V p-p = Voltage peak-to-peak 3 dB max. = Max. frequency where the voltage drops to 3 dB below its setting THD 3 dB = The total harmonic distortion at 3 dB max. frequency THD < 1.5% = The frequency below which the THD is less than 1.5%. Voltage 3 dB max THD 3 dB THD < 1.5% N6761A & N6762A 0.5 Vp-p 4500 Hz 14% 450 Hz 1.0 Vp-p 3600 Hz 14% 450 Hz 2.5 Vp-p 1300 Hz 25% 340 Hz 5.0 Vp-p 600 Hz 25% 250 Hz 50.0 Vp-p 350 Hz 22% 30 Hz N6763A & N6765A 0.2 Vp-p 2300 Hz 10% 1300 Hz 0.4 Vp-p 1500 Hz 15% 800 Hz 1.0 Vp-p 980 Hz 19% 480 Hz 2.0 Vp-p 580 Hz 21% 300 Hz 20.0 Vp-p 400 Hz 12% 32 Hz N6764A & N6766A 0.6 Vp-p 2800 Hz 8.0% 1600 Hz 1.2 Vp-p 1400 Hz 15% 800 Hz 3.0 Vp-p 600 Hz 17% 300 Hz 6.0 Vp-p 400 Hz 20% 200 Hz 60.0 Vp-p 344 Hz 12% 30 Hz N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 33 Chapter 5 Keysight N678xA Source/Measure Units Performance Specifications ........................................................... 36 Supplemental Characteristics ........................................................ 38 Output Quadrant Characteristic .................................................... 43 Output Impedance Graphs............................................................. 44 Voltage Programming Response ................................................... 46 Measurement Accuracy and Resolution ........................................ 48 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 30°C after a 30-minute warm-up period. Unless otherwise noted, specifications apply at the mainframe output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Keysight N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. 35 Performance Specifications N6781A / N6782A N6784A N6785A / N6786A DC Ratings: Voltage Current NOTE 1 Power Auxiliary Voltage Measurement Input NOTE 2 20 V/6 V ±20 V/± 6 V 20 V/15 V/10 V/6 V ± 1 A/± 3 A ± 1 A/± 3 A ± 4 A/± 5 A/± 6.7 A/± 8 A 20 W 20 W 80 W ± 20 V - ± 20 V Output Voltage Ripple & Noise (PARD) from 20 Hz – 20 MHz: Measured at the output terminals, under all load conditions, in Voltage Priority mode. Output Bandwidth setting = Low CV peak-to-peak 12 mV 12 mV 15 mV CV rms 1.2 mV 1.2 mV 1.5 mV Load Effect (Load regulation): For any load change, with a lead drop of 1.0 V. The load lead drop reduces the maximum available voltage at the load. Voltage, 20 V range 700 μV Voltage, 15 V & 10 V ranges Voltage, 6 V range Current, 8 A, 6.7 A, 5 A, & 4 A ranges 700 μV 700 μV - - 700 μV 400 μV 400 μV 700 μV - - 400 μA 100 μA 100 μA - Current, 1 A range 50 μA 50 μA - Current, 300 mA ranges NOTE 3 50 μA - - - 1 μA - Current, 3 A range Current, 100 mA & 10 mA ranges NOTE 3 Source Effect (Line regulation): Source Effect is guaranteed by design. Refer to “Supplemental Characteristics” later in this chapter. Programming Accuracy @ 23 °C ±5 °C: After a 30 minute warm-up. Applies from minimum to maximum programming range at any load. Voltage, 20 V range 0.025% + 1.8 mV Voltage, 15 V & 10 V ranges 0.025% + 1.8 mV 0.025% + 1.8 mV - - 0.025% + 1.8 mV 0.025% + 600 μV 0.025% + 600 μV 0.025% + 1.8 mV 0.025% + 200 μV 0.025% + 200 μV - - - 0.04% + 1.5 mA Current, 3 A & 1 A ranges 0.04% + 300 μA 0.04% + 300 μA - Current, 300 mA range NOTE 3 0.03% + 150 μA - - Voltage, 6V range Voltage, 600 mV range NOTE 3 Current, 8 A, 6.7 A, 5 A, & 4 A ranges Current, 100 mA range - 0.03% + 12 μA - - 0.025% + 5 μA - Resistance for 20 V output range NOTE 2 0.1% + 3 mΩ - 0.1% + 1 mΩ Resistance for 15 V & 10 V ranges NOTE 2 - - 0.1% + 1 mΩ 0.1% + 1.5 mΩ - 0.1% + 1 mΩ NOTE 3 Current, 10 mA range NOTE 3 Resistance for 6 V output range 36 NOTE 2 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Performance Specifications (continued) N6781A / N6782A N6784A N6785A / N6786A Measurement Accuracy @ 23 °C ±5 °C: Applies when measuring the default value of 4883 data points with a 20.48 μs time interval. Refer to “Measurement Accuracy and Resolution” later in this chapter for more information. Voltage, 20 V range 0.025% + 1.2 mV Voltage, 1 V range Voltage, 100 mV range Auxiliary Voltage Measurement Input 0.025% + 1.2 mV 0.025% + 1.8 mV 0.025% + 75 μV 0.025% + 75 μV - 0.025% + 50 μV 0.025% + 50 μV - 0.025% + 5 mV - 0.025% + 5 mV Current, 8 A range - - 0.04% + 1.5 mA Current, 3 A range 0.03% + 250 μA 0.03% + 250 μA - Current, 100 mA range 0.025% + 10 μA 0.025% + 10 μA 0.025% + 10 μA Current, 1 mA range NOTE 4 0.025% + 100 nA (110 nA) 0.025% + 100 nA (110 nA) 0.025% + 100 nA (110 nA) Current, 10 μA range NOTE 4 0.025% + 8 nA (20 nA) 0.025% + 8 nA (20 nA) - NOTE 2 Load Transient Response Time in Voltage Priority mode: Time to recover to within the settling band. With 150 μF cap (ESR=50 mΩ )at load, remote sensing at cap, 4.25' twisted pair load leads-See Service Guide for setup information. Rise time (10% to 90%) 10 μs 10 μs 10 μs Settling band 20 V range with a 0.8 A load step 15 V & 10 V range with a 1.4 A load step 6 V range with a 1.4 A load step ± 10 mV ± 20 mV ± 10 mV ± 20 mV ± 20 mV NOTE 5 ± 20 mV ± 20 mV Recovery time ≤ 35 μs ≤ 35 μs ≤ 35 μs Output current is derated 1% per °C above 30°C. Applies to N6781A and N6785A only. Add an additional voltage programming error of 1 mV/Ω for N6781A and 10 mV/Ω for N6785A is also present. 3 600 mV range is only available in Voltage Priority mode; 300 mA, 100 mA, 10 mA ranges are only available in Current Priority mode. 4 Values in parentheses apply when power modules are installed in Keysight N6705A mainframes. 5 Applies with a 1.4 A load step. 1 2 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 37 Supplemental Characteristics N6781A / N6782A N6784A N6785A / N6786A 10 mA 10 mA 8 mA - - 8 mA 20 mA 20 mA 8 mA - - 20 mV 3 A range Current Priority mode 10 mV 10 mV - 1 A range Current Priority mode 20 mV 20 mV - Voltage, 20 V range 0 to 20.4 V; 200 μV -20.4 V to 20.4 V; 200 μV 0 to 20.4 V; 200 μV Voltage, 15 V range - - 0 to 15.3 V; 200 μV Voltage, 10 V range - - 0 to 10.2 V; 200 μV Voltage, 6 V range 0 to 6.12 V; 60 μV -6.12 V to 6.12 V; 60 μV 0 to 6.12 V; 200 μV Voltage, 600 mV range Minimum Current and Voltage Compliance limits: 20 V range Voltage Priority mode 10 V & 15 V ranges Voltage Priority mode 6 V range Voltage Priority mode 8 A, 6.7 A, 5 A, & 4 A ranges Current Priority Programming Range & Resolution: 0 to 612 mV; 6 μV -612 mV to 612 mV; 6 μV - Current, 8 A range - - -8.16 A to 8.16 A; 75 μA Current, 6.7 A range - - -6.83 A to 6.83 A; 75 μA Current, 5 A range - - -5.1 A to 5.1 A; 75 μA Current, 4 A range - - -4.08 A to 4.08 A; 75 μA Current, 3 A range -3.06 A to 3.06 A; 25 μA -3.06 A to 3.06 A; 25 μA - Current, 1 A range -1.02 A to 1.02 A; 25 μA -1.02 A to 1.02 A; 25 μA - Current, 300 mA range -306 mA to 306 mA; 3 μA - - Current, 100 mA range - -102 mA to 102 mA; 1 μA - - -10.2 mA to 10.2 mA; 0.1 μA - -40mΩ to +1Ω; 0.5mΩ - -40mΩ to +1Ω; 0.17mΩ Current, 10 mA range Resistance for 20 V range NOTE 1 Resistance for 15 V, & 10 V ranges NOTE 1 - - -40mΩ to +1Ω; 0.17mΩ -40mΩ to +1Ω; 0.25m - -40mΩ to +1Ω; 0.17mΩ 0.002% +120uV 0.002% +120uV 0.0025% +200uV - - 0.0025% +200uV Voltage, 6 V range 0.0015% +40uV 0.0015% +40uV 0.0025% +200uV Voltage, 600 mV range 0.0015% +10uV 0.0015% +10uV - - - 0.0025% +150uA Current, 3 A & 1 A ranges 0.0025% +22uA 0.0025% +22uA - Current, 300 mA range 0.0025% +14uA - - Current, 100 mA range - 0.0025% +1uA - Current, 10 mA range - 0.0025% +0.5 μA - 200 μV 10 μV 1 μV 800 μV 200 μV 10 μV 1 μV - 200 μV 800 μV 25 uA 1 uA 10 nA 0.1 nA 25 uA 1 uA 10 nA 0.1 nA 75 uA 1 uA 10 nA - Resistance for 6 V range NOTE 1 Programming Accuracy Temperature Coefficient per °C: Voltage, 20 V range Voltage, 10 V & 15 V ranges Current, 8 A, 6.7 A, 5 A, & 4 A ranges Measurement Resolution: Voltage, 20 V range Voltage,1 V range Voltage, 100 mV range Auxiliary Voltage Measurement Input NOTE 1 Measurement Resolution (continued) Current, 8 A range Current, 3 A range Current, 100 mA range Current, 1 mA range Current, 10 μA range 38 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6781A / N6782A N6784A N6785A / N6786A Measurement Accuracy Temperature Coefficient per °C: 0.003% +75 uV 0.0007% +200 uV 0.002% +110 uA 0.0025% +0.4 uA 0.002% +5 nA - 0.0025% +25 uV 0.002% +2.5 uV 0.0025% +2.5 uV 0.0025% +14 uA 0.0025% +0.4 uA 0.002% +5 nA 0.002% +0.55 nA 0.0025% +25 uV 0.002% +2.5 uV 0.0025% +2.5 uV 0.0007% +200 uV 0.0025% +14 uA 0.0025% +0.4 uA 0.002% +5 nA 0.002% +0.55 nA Voltage, 20 V range Voltage, 1 V range Voltage, 100 mV range Auxiliary Voltage Measurement Input NOTE 1 Current, 8 A range Current, 3 A range Current, 100 mA range Current, 1 mA range Current, 10 μA range Voltage Programming Speed & Settling Time: (At the specified bandwidth) With slew rate set to maximum; with High 2 output cap = 1 uF; with High 3 output cap = 7 uF Compensation setting Low High1 High 2 High 3 Low High1 High 2 High 3 Low High1 High2 High3 Rise Time from 10% to 90% of step 20 V range with a 0-10 V step NOTE 2 15 V & 10 V ranges with a 0-4 V step 6 V range with a 0-4 V step 600 mV range with a 0-500 mV step 300 μs 15 μs 20 μs 120 μs 300 μs 15 μs 20 μs 120 μs 300μs 12 μs 300μs 12 μs 300 μs 20 μs 22 μs 50 μs 300 μs 20 μs 22 μs 50 μs 300μs 12 μs 400 μs 75 μs 30 μs 50 μs 400 μs 75 μs 30 μs 50 μs - 15 μs 15 μs 15 μs - 40μs 40μs 40μs - Settling Time to 0.1% of step 20 V range with a 0-10 V step NOTE 2 15 V, & 10 V ranges with a 0-4 V step 6 V range with a 0-4 V step 600 mV range with a 0-500 mV step 850 μs 45 μs 65 μs 240 μs 850 μs 45 μs 65 μs 240 μs 1.2ms 1.2ms 850 μs 55 μs 65 μs 160 μs 850 μs 55 μs 65 μs 160 μs 1.2ms 1.2 ms 220 μs 85 μs 170 μs 1.2 ms 220 μs 85 μs 170 μs - 50 μs 50 μs 50 μs - 120μs 120μs 120μs - 40 μs 40 μs 40 μs - High Frequency Output Voltage Noise: (At the specified bandwidth) With High 2 setting, output cap = 1 uF; with High 3 setting, output cap = 7 uF Compensation setting Low High1 High 2 High 3 Low High1 High 2 High 3 Low High1 High2 High3 CV peak-to-peak from 20Hz - 20 MHz 20 V range with any load 15 V & 10 V ranges with any load 6 V range with any load 600 mV range with any load 12 mV 12 mV 4 mV 12 mV 12 mV 4 mV 12 mV 12 mV 4 mV CV rms from 20 Hz – 20 MHz 20 V range with any load 15 V & 10 V ranges with any load 6 V range with any load 600 mV range with any load 1.2 mV 1.2 mV 0.5 mV 0.5 mV 1.2 mV 1.2 mV 0.5 mV 0.5 mV 1.5mV 1.5mV 0.4mV 0.3mV 1.5mV 1.5mV 0.4mV 0.3mV 1 mV 1 mV 0.3 mV 0.3 mV 1 mV 1 mV 0.3 mV 0.3 mV 1.5mV 1.5mV 0.4mV 0.3mV 1 mV 1 mV 0.3 mV 0.3 mV 1 mV 1 mV 0.3 mV 0.3 mV - 4 mV 12 mV 12 mV 4 mV 3 mV 12 mV 12 mV 4 mV 3 mV 12 mV 12 mV 4 mV 4 mV 3 mV 3 mV 15mV 15mV 15mV 15mV 15mV 15mV - 3 mV 3 mV 3 mV - 3 mV 3 mV 3 mV - Low Frequency Output Voltage Noise: CV peak to peak from 0.1 Hz – 10 Hz 20 V range 6 V range 600 mV range CV rms from 0.1 Hz – 10 Hz 20 V range 6 V range 600 mV range - 100 μV 50 μV 20 μV - - 20 μV 10 μV 5 μV - Voltage Programming Small Signal Bandwidth: Refer to “Voltage Programming Response” later in this chapter. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 39 Supplemental Characteristics (continued) N6781A / N6782A Voltage Measurement Noise: (peak value) 20 V range 1 V range 100 mV range N6784A 3 mV 250 μV 50 μV N6785A / N6786A 3 mV 250 μV 50 μV 2.9 mV - 40 μs 35 μs DC to 30 kHz DC to 17 kHz - DC to 30 kHz DC to 17 kHz - Voltage Measurement Settling Time: (All ranges) Settling Time with no range change 40 μs Voltage Measurement Small Signal Bandwidth: (All ranges) –3 db typical with seamless ranging Off with seamless ranging On –1 db typical with seamless ranging Off with Seamless ranging On DC DC DC DC to 30 kHz to 27 kHz to 17 kHz to 15 kHz Voltage Priority Transient Characteristic: (Time to recover to within the settling band) At the specified bandwidth, 6 V range only, with remote sensing at load cap, 4.25' twisted pair load leads. Compensation setting Settling band. Low High1 High2 High3 Low High1 High2 High3 Low High1 High2 High3 40 mV 50 mV 30 mV 20 mV 40 mV 50 mV 30 mV 20 mV 40 mV 50 mV 30 mV 20 mV CC Load Step 0.2 A 0.2 A 0.5 A 1.4 A 0.2 A 0.2 A 0.5 A 1.4 A 0.2 A 0.2 A 0.5 A 1.4 A Rise Time from 10% to 90% of step 10 μs 5 μs 5 μs 10 μs 10 μs 5 μs 5 μs 10 μs 10 μs 5 μs 5 μs 10 μs Recovery time with no load cap with 1μF load cap (ESR=50 mΩ) with 6.8μF load cap (ESR=50 mΩ) with 150μF load cap (ESR=50 mΩ) 30 μs 10 μs 30 μs 10 μs 20 μs 10 μs 20 μs 10 μs 25 μs 15 μs 25 μs 15 μs 140 μs 35 μs 140 μs 35 μs 40 μs 150 μs 12 μs 20 μs - 12 μs 14 μs - 15 μs 25 μs Maximum peak voltage deviation with no load cap with 1μF load cap (ESR=50 mΩ) with 6.8μF load cap (ESR=50 mΩ) with 150μF load cap (ESR=50 mΩ) 180 mV 200 mV 180 mV200 mV 250mV 260mV - 260 mV 140 mV - 260 mV 140 mV 290mV 140mV - 140 mV 60 mV - 140 mV 60 mV 140mV 60 mV 45 mV 45 mV 45 mV 45 mV 65 mV 45 mV Auxiliary Voltage Measurement Input: NOTE 1 Differential input resistance Maximum conversion rate Maximum voltage from common Maximum continuous input without damage 10 MΩ 100k samples/second ± 240 VDC ± 60 V - 10 MΩ 100k samples/second ± 240 VDC ± 60 V 0.05% + 20 mV 24 V 0.05% + 20 mV 24 V 0.05% + 20 mV 24 V <30 µs 30 to 272 µs; 30 µs <30 µs 30 to 272 µs; 30 µs <30 µs 30 to 272 µs; 30 µs 300 μV 60 μA 300 μV 60 μA 100 μV 100 μA 2.8 μs 3.2 μs 3.5 μs - 2.8 μs 3.2 μs 4 μs 5 μs 3.0 μs - Over-Voltage Protection: Accuracy Maximum setting Response time NOTE 3 Programmable delay range & default value Source Effect (Line regulation): Voltage, all ranges Current, all ranges Current Programming Speed & Settling Time: Rise Time from 10% to 90% of step 8 A range with a 0-8 A step 3 A range with a 0-3 A step 1 A range with a 0-1 A step 300 mA range with a 0-300 mA step 100 mA range with a 0-100 mA step 10 mA range with a 0-10 mA step 40 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6781A / N6782A Current Programming Speed & Settling Time (continued) Settling Time to 0.1% of step 8 A range with a 0-8 A step 3 A range with a 0-3 A step 1 A range with a 0-1 A step 300 mA range with a 0-300 mA step 100 mA range with a 0-100 mA step 10 mA range with a 0-10 mA step N6784A N6785A / N6786A 30 μs 30 μs 30 μs 30 μs 20 μs - 200 μA 1 mA 2 μA 50 nA 20 nA - 30 μs 30 μs 40 μs - High Frequency Output Current Noise: (All ranges) CC rms from 20 Hz – 20 MHz 200 μA Low Frequency Output Current Noise: (CC rms from 0.1 Hz – 10 Hz) 3 A & 1 A ranges 100 mA range 10 mA range - Current Programming Small Signal Bandwidth: –3 dB all except 100 mA & 10 mA range for 100 mA & 10 mA range DC to 120 kHz - DC to 120 kHz DC to 100 kHz DC to 130 kHz - –1 dB all except 100 mA & 10 mA range for 100 mA & 10 mA range DC to 75 kHz - DC to 75 kHz DC to 50 kHz DC to 70 kHz - 400 μA 20 μA 2 μA 20 nA 1.2 mA 13.5 μA 1.4 μA - Current Measurement Noise: (Peak value) 400 μA 20 μA 2 μA 20 nA 8 A range 3 A range 100 mA range 1 mA range 10 μA range Current Measurement Settling Time: (to 1% of the specified step with no range change or with up-ranging) 8 A range with 0.5-1A step 3 A range with a 0.5-1 A step 100 mA range with a 50-100 mA step 1 mA range with a 0.5-1 mA step 10 μA range with a 5-10 μA step Up-ranging to 8 A range with a 0-8 A step 3 A range with a 0-3 A step 100 mA range with a 0-100 mA step 1 mA range with a 0-1 mA step 35 μs 35 μs 120 μs 750 μs 35 μs 35 μs 120 μs - 35 μs 35 μs 120 μs (to 1% of the specified range with down-ranging) 35 μs 35 μs - 35 μs 35 μs 120 μs 750 μs Down-ranging from 3 A & 8 A ranges to: 100 mA range 1 mA range 10 μA range 45 μs 200 μs 3.5 ms 45 μs 200 μs 3.5 ms 50 μs 200 μs - Current Measurement Small Signal Bandwidth: NOTE 4 –3 dB typical with seamless ranging Off 8 A range 3 A range 100 mA range 1 mA range 10 μA range N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide DC DC DC DC to 29 kHz to 29 kHz to 10 kHz to 750 Hz DC DC DC DC to 27 kHz to 27 kHz to 10 kHz to 750 Hz DC to 28 kHz DC to 30 kHz DC to 10 kHz - 41 Supplemental Characteristics (continued) N6781A / N6782A Current Measurement Small Signal Bandwidth (continued) –3 dB typical with seamless ranging On 8 A range 3 A range 100 mA range 1 mA range –1 dB typical with seamless ranging Off 8 A range 3 A range 100 mA range 1 mA range 10 μA range –1 dB typical with seamless ranging On 8 A range 3 A range 100 mA range 1 mA range N6784A N6785A / N6786A DC to 26 kHz DC to 26 kHz DC to 10 kHz - DC to 26 kHz DC to 27 kHz DC to 10 kHz DC to 16 kHz DC to 16 kHz DC to 6 kHz DC to 400 Hz DC to 16 kHz DC to 16 kHz DC to 6.5 kHz DC to 400 Hz DC to 16 kHz DC to 17 kHz DC to 6 kHz - DC to 14 kHz DC to 14 kHz DC to 6 kHz - DC to 15 kHz DC to 15 kHz DC to 16 kHz Current Priority Transient Characteristic: (with 4.25' twisted pair load leads) 8 A range with a 5-15 V step Current settling band Recovery time NOTE 5 - - 40 mA 5 μs (7 μs) 3 A range with a 1-4 V step Current settling band Recovery time NOTE 5 5 mA 12 μs (24 μs) 5 mA 12 μs (24 μs) - 1 A range with a 0.5-0 V step Current settling band Recovery time NOTE 5 10 mA 12 μs (24 μs) 10 mA 12 μs (24 μs) - Common Mode Current from 20 Hz – 20 MHz: (with negative output connected to chassis) CC peak-to-peak CC rms < 1 mA < 1 mA < 1.5 mA < 100 μA < 100 μA < 150 μA Remote Sense Capability: Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Parallel Operation: NOTE 6 Identically rated outputs can be operated directly in parallel in Current Priority mode only. Operating units in series is not available. Minimum Output Turn-on Delay: (Time from when any Output On command is received until the output starts turning on.) Turn-off mode set to Low impedance 25.6 ms 25.6 ms 25.6 ms Turn-off mode set to High impedance 24.7 ms 24.7 ms 24.7 ms Applies to N6781A and N6785A only For N6785A and N6786A applies with a 0 - 4 V step. 3 Response time applies from the occurrence of the over-voltage condition to the start of output shutdown. 4 When using an N6705A mainframe connected through the front panel binding posts, additional output capacitance causes large measurement peaking/overshoots when the load impedance is >~1 kΩ. This does not apply to N6705B mainframes. When using an N6705A or N6705B mainframe connected directly to the module connector, there are slight measurement peaking/overshoots when the load impedance is > ~10 kΩ. 5 Values in parentheses apply when power modules are installed in N6705A mainframes. 6 In CV priority mode, uneven current sharing while paralleling prevents using the lower current measurement ranges and will also cause degradation in transient response performance. 1 2 42 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Output Quadrant Characteristic Voltage N6781A, N6782A, 20 W Voltage +1 A +20 V -1 A +1 A +20 V N6784A, 20 W +3 A +6 V +3 A -3 A +6 V Current 0 Current -6 V -3 A 0 Key -20 V -1 A Sourcing power Sinking power Voltage Note 1 Voltage -0.9 A N6785A, N6786A, -4 A 80 W -5 A +4 A, +20 V +15 V +5 A, +15 V +6.7 A, +10 V +8 A, +6 V -6.7 A -8 A Current 0 -2.3 A Current +2.2 V -2.2 V N6784A Downprogrammer derating +2.3 A -15 V +0.9 A Note 1. When sinking power, Keysight Model N6784A can operate at the maximum rated output power for only a limited time. When the internal temperature of the unit exceeds its safe limit, the output latches off. A protect clear is required to resume normal operation. The condition is annunciated by the OT status bit. The Downprogrammer derating figure shows the safe limit boundary values. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 43 Output Impedance Graphs N6781A N6782A N6784A CV Mode @3V, 0.5A N6781A N6782A N6784A CC Mode @2.4V, 0.4A 44 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide N6785A N6786A CV Mode @3V, 0.5A N6785A N6786A CC Mode @2.4V, 0.4A N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 45 Voltage Programming Response The following graphs show the voltage programming response with the indicated bandwidths and loads. Note that the load ESR=200 mΩ. N6781A N6782A N6784A Bandwidth LOW HIGH 1 N6781A N6782A N6784A Bandwidth HIGH 2 HIGH 3 46 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide N6785A N6786A Bandwidth LOW HIGH 1 N6785A N6786A Bandwidth HIGH 2 HIGH 3 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 47 Measurement Accuracy and Resolution (with shorter measurement intervals) The following table shows changes to the short-term measurement accuracy and resolution with various number of power line cycle (NPLC) measurement settings. Changes are due to the A-to-D converter’s noise performance. The table’s baseline is 1 NPLC with no added noise. To determine the measurement accuracy at shorter averaging intervals, simply add the noise value to the fixed accuracy value in the specification table. N6785A and N6786A NPLC @ 60 Hz: 0.0003 0.003 0.006 0.010 0.031 0.06 0.1 0.6 1 Time: 5.1E-6 51.2E-6 102.4E-6 169E-6 512E-6 998.4E-6 1.7E-3 10E-3 16.7E-3 Averaged points: 1 10 20 33 100 195 325 1953 3255 20V range noise: 2.9E-3 1.3E-3 1.0E-3 1.0E-3 394.2E-6 298.5E-6 260.6E-6 98.1E-6 69.8E-6 Resolution (bits): 12.7 13.9 14.2 14.2 15.6 16 16.2 17.6 18.1 8A range noise: 1.2E-3 552.2E-6 409.7E-6 313.8E-6 198.9E-6 138.0E-6 94.4E-6 45.6E-6 43.5E-6 Resolution (bits): 12.7 13.8 14.2 14.6 15.2 15.8 16.3 17.4 17.4 13.5E-6 7.1E-6 5.4E-6 4.1E-6 2.5E-6 1.7E-6 1.3E-6 644.2E-9 471.5E-9 100mA range noise: Resolution (bits): 12.8 13.7 14.1 14.5 15.2 15.8 16.2 17.2 17.6 1mA range noise: 1.4E-6 594.3E-9 306.2E-9 191.0E-9 67.7E-9 38.8E-9 23.8E-9 8.2E-9 6.9E-9 Resolution (bits): 9.4 10.7 11.6 12.3 13.8 14.6 15.3 16.8 17.1 N6781A, N6782A and N6784A NPLC @ 60 Hz: 0.0003 0.003 0.006 0.010 0.031 0.06 0.1 0.6 1 Time: 5.1E-6 51.2E-6 102.4E-6 169E-6 512E-6 998.4E-6 1.7E-3 10E-3 16.7E-3 Averaged points: 1 10 20 33 100 195 325 1953 3255 20V range noise: 2.3E-3 1.2E-3 993.7E-6 894.8E-6 533.4E-6 297.5E-6 276.6E-6 87.4E-6 69.6E-6 Resolution (bits): 13 14 14.2 14.4 15.1 16 16.1 17.7 18.1 1V range noise: 186.6E-6 Resolution (bits): 100mV range noise: Resolution (bits): 90.3E-6 57.0E-6 45.5E-6 26.7E-6 22.1E-6 19.8E-6 7.1E-6 4.8E-6 12.3 13.4 14 14.4 15.1 15.4 15.6 17.1 17.6 38.9E-6 20.7E-6 12.5E-6 10.5E-6 5.9E-6 5.1E-6 5.0E-6 3.9E-6 3.4E-6 11.3 12.2 12.9 13.2 14 14.2 14.2 14.6 14.8 3A range noise: 480.3E-6 Resolution (bits): 100mA range noise: 159.7E-6 120.5E-6 71.0E-6 48.3E-6 41.4E-6 16.8E-6 18.5E-6 13.8 14.2 14.6 15.3 15.9 16.1 17.4 17.2 14.1E-6 8.7E-6 6.4E-6 4.4E-6 2.5E-6 2.2E-6 1.5E-6 858.1E-9 573.3E-9 Resolution (bits): 12.8 13.4 13.9 14.4 15.2 15.4 16 16.8 17.4 1mA range noise: 1.8E-6 798.7E-9 363.1E-9 248.5E-9 74.1E-9 44.8E-9 27.3E-9 8.5E-9 6.8E-9 Resolution (bits): 9.1 10.2 11.4 11.9 13.7 14.4 15.1 16.8 17.1 15.9E-9 18.0E-9 20.3E-9 15.4E-9 11.0E-9 4.8E-9 3.3E-9 9.2 9.1 8.9 9.3 9.8 11 11.5 10uA range noise: Resolution (bits): 48 206.4E-6 12.6 752.2E-12 456.3E-12 13.7 14.4 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 6 Keysight N6783A-BAT, N6783A-MFG Application-Specific Power Modules Performance Specifications ........................................................... 50 Supplemental Characteristics ........................................................ 51 Output Quadrant Characteristic .................................................... 52 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Keysight N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. 49 Performance Specifications N6783A-BAT N6783A-MFG 0-8V 0-6V – 2 to +3 A – 2; 0 to +3 A 24 W 18 W 150 mA 150 mA 8 mV 8 mV 1.5 mV 1.5 mV DC Ratings: Voltage Current NOTE 1 Power Low current measurement range Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) CV peak-to-peak CV rms Load Effect (Regulation): (For any output load change, with a maximum load-lead drop of 0.5V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 6 mV 6 mV Current 2 mA 2 mA Voltage 2 mV 2 mV Current 1 mA 1 mA Voltage 0.1% + 10 mV 0.1% + 10 mV Positive Current 0.1% + 1.8 mA 0.1% + 1.8 mA Negative Current @ –2 A 0.2% + 1.8 mA N/A Source Effect (Regulation): Programming Accuracy: (@ 23 °C ±5 °C after a 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.05% + 5 mV 0.05% + 5 mV Current high range 0.1% + 600 µA 0.1% + 600 µA Current low range 0.1% + 75 µA 0.1% + 75 µA Load Transient Recovery (Time to recover to within settling band for a load change from 0.15 A to 1.5 A and from 1.5 A to 0.15 A at 6 V output) Voltage settling band NOTE 2 ± 75 mV ± 75 mV Time NOTE 2 < 45 µs < 45 µs 1 Output current is derated 1% per °C above 40°C. 2 When relay Option 761 is installed, the settling band is ± 90 mV. The time is < 75 µs. 50 N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6783A-BAT N6783A-MFG 15 mV to 8.16 V 5 mA to 3.06 A – 5 mA to – 2 A 15 mV to 6.12 V 5 mA to 3.06 A Fixed at – 2 A 2.5 mV 1 mA 10 mA 2.5 mV 1 mA N/A 300 µV 100 µA 5 µA 300 µV 100 µA 5 µA 25 ppm + 50 µV 25 ppm + 10 µA 25 ppm + 50 µV 25 ppm + 10 µA 25 ppm + 40 µV 25 ppm + 2.5 µA 25 ppm + 1.5 µA 25 ppm + 40 µV 25 ppm + 2.5 µA 25 ppm + 1.5 µA Programming Ranges: Voltage Positive Current Negative Current Programming Resolution: Voltage Positive Current Negative Current Measurement Resolution: Voltage Current high range Current low range (≤ 0.150 A) Programming Temperature Coefficient per °C: Voltage Current Measurement Temperature Coefficient per °C: Voltage Current high range Current low range (≤ 0.150 A) Maximum Up-Programming and Down-Programming Time with Full Resistive Load (Time from 10% to 90% of total voltage excursion) Voltage Settling from 0V to Full Scale 4.0 ms 4.0 ms Voltage Settling from Full Scale to 0V 4.0 ms 4.0 ms Maximum Up-Programming and Down-Programming Settling Time with Full Resistive Load (Time from start of voltage change until voltage settles within 0.1% of the full-scale voltage of its final value) Voltage Settling from 0V to Full Scale 20 ms 20 ms Voltage Settling from Full Scale to 0V 20 ms 20 ms 0.25% + 75 mV 0.25% + 275 mV 0 – 10 V 60 µs – 5 ms 0.25% + 75 mV 0.25% + 275 mV 0 – 10 V 60 µs – 5 ms 0 – 255 ms 5 mA – 3.06 A 0 – 255 ms 5 mA – 3.06 A 4 mA 4 mA Rms 1 mA 1 mA Peak-to-peak 6 mA 6 mA Over-voltage Protection: Accuracy without disconnect relays Accuracy with disconnect relays Nominal range Programmable delay time Over-Current Protection: Programmable delay time Nominal Range Output Ripple and Noise: (PARD) CC rms: Common Mode Noise: (From 20 Hz – 20 MHz; from either output to chassis) Remote Sense Capability: Outputs can maintain DC specifications with up to a 0.5-volt drop per load lead. Maximum sense lead resistance is limited to 300mΩ/lead. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 51 Supplemental Characteristics (continued) N6783A-BAT N6783A-MFG Series and Parallel Operation: Identically rated outputs can be operated directly in parallel. N6783A modules cannot be used in series with other N6783A modules or any other N67xx module. Down-programming Capability: (Current down-programming capability is reduced at output voltages below 0.5 V) Continuous power 12 W Continuous current 12 W 2A 2A Output Quadrant Characteristic N6783A-BAT N6783A-MFG Voltage +8 V (BAT) +6 V (MFG) Current -2 A 0 Key Sourcing power Sinking power 52 +3 A Negative current not programmable on N6783A-MFG N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 7 Keysight N6700 Modular Power System Mainframes Supplemental Characteristics ........................................................ 54 Outline Diagrams............................................................................ 56 Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. NOTE Refer to the following documents for information about using and servicing the Keysight N6700 Modular Power System Mainframes Keysight Model N6705 DC Power Analyzer User’s Guide Go to http:// literature.cdn.keysight.com/litweb/pdf/N6705-90001.pdf. Keysight Model N6705 DC Power Analyzer Service Guide Go to http:// literature.cdn.keysight.com/litweb/pdf/N6705-90010.pdf. Keysight Series N6700 Low-Profile Modular Power System User’s Guide Go to http:// literature.cdn.keysight.com/litweb/pdf/5969-2937.pdf. Keysight Series N6700 Low-Profile Modular Power System Service Guide Go to http:// literature.cdn.keysight.com/litweb/pdf/5969-2938.pdf. 53 Supplemental Characteristics N6700B, N6701A, N6702A N6705A, N6705B 400 W (for N6700B mainframes) 600 W (for N6701A mainframes) 1200 W (for N6702A mainframes) 600 W N/A 20 A N/A N/A Digital TTL level compatible 5V N/A N/A 200 mA 300 mA Maximum Power Available for Modules: Values represent combined power rating of all modules installed per mainframe. Front Panel Output Terminals: Maximum current rating BNC Trigger Connectors: I/O Maximum voltage USB Current Ratings: Front panel USB connector Rear panel USB connector Data Storage: Internal flash memory 8 Mbyte 4 Gbyte (Earlier N6705 models have less memory) Protection Response Characteristic: INH input Fault on coupled outputs 5 µs from receipt of inhibit to start of shutdown < 10 µs from receipt of fault to start of shutdown Command Processing Time: ≤ 1 ms from receipt of command to start of output change Digital Port Characteristics: Maximum voltage ratings +16.5 VDC/− 5 VDC between pins (pin 8 is internally connected to chassis ground). Pins 1 and 2 as FLT output Maximum low-level output voltage = 0.5 V @ 4 mA Maximum low-level sink current = 4 mA Typical high-level leakage current = 1 mA @ 16.5 VDC Pins 1 - 7 as digital/trigger outputs (pin 8 = common) Maximum low-level output voltage = 0.5 V @ 4 mA; 1 V @ 50 mA; 1.75 V @ 100 mA Maximum low-level sink current = 100 mA Typical high-level leakage current = 0.8 mA @ 16.5 VDC Pins 1 - 7 as digital/trigger inputs and pin 3 as INH input (pin 8 = common) Maximum low-level input voltage = 0.8 V Minimum high-level input voltage = 2 V Typical low-level current = 2 mA @ 0 V (internal 2.2k pull-up) Typical high-level leakage current = 0.12 mA @ 16.5 VDC Interface Capabilities: GPIB LXI Compliance USB 2.0 10/100 LAN Built-in Web server 54 SCPI - 1993, IEEE 488.2 compliant interface Class C (only applies to units with LXI label on front panel) Requires Keysight IO Library version M.01.01 or 14.0 and up Requires Keysight IO Library version L.01.01 or 14.0 and up Requires Internet Explorer 7+ or Firefox 2+ N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6700B, N6701A, N6702A N6705A, N6705B Regulatory Compliance: EMC Complies with European EMC Directive for test and measurement products. ● IEC/EN 61326-1 ● CISPR 11, Group 1, class A ● AS/NZS CISPR 11 ● ICES/NMB-001 Complies with Australian standard and carries C-Tick mark. This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada. Complies with European Low Voltage Directive and carries the CE-marking. Conforms to UL 61010-1 and CSA C22.2 61010-1. Safety Environmental Conditions Operating environment Temperature range Relative humidity Altitude Storage temperature Indoor use, installation category II (for AC input), pollution degree 2 0°C to 55°C (output current is derated 1% per °C above 40°C ambient temperature) Up to 95% Up to 2000 meters -30°C to 70°C Acoustic Noise Declaration: This statement is provided to comply with the requirements of the German Sound Emission Directive, from 18 January 1991. Sound Pressure Lp <70 dB(A), At Operator Position, Normal Operation, According to EN 27779 (Type Test). Schalldruckpegel Lp <70 dB(A), Am Arbeitsplatz, Normaler Betrieb, Nach EN 27779 (Typprüfung). Output Terminal Isolation: No output terminal may be more than ±240 VDC from any other terminal or chassis ground. Maximum rating N6781A Note When using the AUX measurement input terminals on Model N6781A, no output or input terminal may be more than ±60 VDC from any other terminal and chassis ground. AC Input: Input Ratings Power Consumption Power Factor Fuse N6702A Note ~ 100 VAC – 240 VAC; 50/60/400Hz ~ 100 VAC – 240 VAC; 50/60/400Hz 1000 VA (N6700B) 1440 VA 1440 VA (N6701A) 1440 VA (N6702A @ < 180 VAC input) 2200 VA (N6702A @ > 180 VAC input) 0.99 @ nominal input and rated power 0.99 @ nominal input and rated power Internal fuse - not customer accessible. Internal fuse - not customer accessible. AC mains circuits rated at 100-180 VAC cannot supply enough current to power the N6702A mainframe when operated at its full rated power. When connected to a 100180 VAC mains, internal circuits will limit the power to modules to 600 W maximum. Net Weight: (typical) Mainframe with 4 modules N6700B 12.73 kg / 28 lbs N6701A 11.82 kg / 26 lbs N6702A 14.09 kg / 31 lbs 1.23 kg / 2.71 lbs Single-wide power module 16 kg / 35 lbs 1.23 kg / 2.71 lbs Dimensions: Refer to the outline diagrams on the following page. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 55 Outline Diagrams 272.6 mm 10.733 in. = airflow 16.9 mm 0.663 in. 425.6 mm 16.756 in. 23.5 mm 0.923 in. 17.7 mm 0.697 in. 56 177.0 mm 6.968 in. N6731B-N6786A DC Power Modules N6700B-N6705B Mainframes Specifications Guide This information is subject to change without notice. © Keysight Technologies 2010 - 2015 Edition 8, January 2015 N6700-90001 www.keysight.com