Power-One HPT015YEHH-A Hpt series - triple output, 15 watt Datasheet

(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com
HPT SERIES - TRIPLE OUTPUT, 15 WATT
DESCRIPTION
FEATURES
HPT triple output DC/DC converters provide
15 Watts of output power in an industry standard
package. HPT’s feature excellent efficiency and
industry-leading power density. The HPT has openframe packaging to provide maximum useable power
with minimal thermal constraints. These units are
fully compatible with production board washing
processes.
•
•
•
•
Triple Output 2” X 2”
Open-Frame Packaging
2.5 Million Hours MTBF
Short Circuit and
Overvoltage Protection
• 500V Isolation
• Input Undervoltage
Lockout
• 3-1 Wide Voltage
Input
• 100°C Baseplate
Operation
TECHNICAL SPECIFICATIONS
Input
Voltage Range
24 VDC Nominal
48 VDC Nominal
48 VDC Wide
10 - 30 VDC
34 - 75 VDC
20 - 60 VDC
Output
Setpoint Accuracy
Auxiliary Setpoint Accuracy
Line Regulation Vin Min. - Vin Max., Iout Rated
Load Regulation Iout Min. - Iout Max., Vin Nom.
Minimum Output Current
Dynamic Regulation, Loadstep
Pk Deviation
Settling Time
Ripple and Noise w/ 25 MHz BW, Pk-Pk / RMS
Current Limit Type
Current Limit Threshold Range, % of Iout Rated
Short Circuit Current Max.
OVP Trip Range
OVP Type
±1%
5%
±1% Vout
±1% Vout
10 % Iout Rated
25% Iout
1% Vout
250 µs
1% / 0.3% Vout
Hiccup
110 - 140%
200% Iout Nom.
110 - 140% Vout Nom.
Second Control Loop
General
Switching Frequency
Isolation
Input - Output
Input - Case
Output - Case
Temperature Coefficient
Case Temperature
Operating Range
Storage Range
Thermal Shutdown Range
Humidity Max., Non-Condensing
Vibration, 3 Axes, 5 Min Each
MTBF† (Bellcore TR-NWT-000332)
Safety
Weight (approx.)
200 kHz
500 VDC
500 VDC
500 VDC
0.02 ppm/°C
-40 to +100°C
-40 to +125°C
105 to 115°C
95%
2g
2.5 x 106 hrs
Consult Factory
0.85 oz
1
Notes
1
For negative logic, add suffix “N” to model number.
†
MTBF predictions may vary slightly from model to model.
Specifications typically at 25°C, normal line, and full load, unless otherwise stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory
for specific model information.
Units are water-washable and fully compatible with commercial spray or immersion
post wave-solder washing equipment.
HPT SERIES - TRIPLE OUTPUT, 15 WATT
MODELS - (See the last page of this file for options.)
Vin
(Volts)
Vin Range
(Volts)
Iin Max.*
(Amps)
Vout
(Volts)
Iout Rated
(Amps)
24
24
24
24
48
48
48
48
48 WIDE
48 WIDE
48 WIDE
48 WIDE
18 - 36
18 - 36
18 - 36
18 - 36
34 - 75
34 - 75
34 - 75
34 - 75
20 - 60
20 - 60
20 - 60
20 - 60
1.90
1.90
1.84
1.84
0.56
0.56
0.54
0.54
0.95
0.95
0.92
0.92
3.3, –12
3.3, –15
5, –12
5, –15
3.3, –12
3.3, –15
5, –12
5, –15
3.3, –12
3.3, –15
5, –12
5, –15
2.3,
2.3,
1.5,
1.5,
2.3,
2.3,
1.5,
1.5,
2.3,
2.3,
1.5,
1.5,
Ripple & Noise
Pk-Pk (mV)
100,
100,
100,
100,
100,
100,
100,
100,
100,
100,
100,
100,
–0.31
–0.25
–0.31
–0.25
–0.31
–0.25
–0.31
–0.25
–0.31
–0.25
–0.31
–0.25
–200
–200
–200
–200
–200
–200
–200
–200
–200
–200
–200
–200
Efficiency
Typ. **
Model
HPT015YEHH-A
HPT015YEJJ-A
HPT015YGHH-A
HPT015YGJJ-A
HPT015ZEHH-AS1
HPT015ZEJJ-AS1
HPT015ZGHH-AS1
HPT015ZGJJ-AS1
HPT015ZEHH-A
HPT015ZEJJ-A
HPT015ZGHH-A
HPT015ZGJJ-A
80%
80%
83%
83%
80%
80%
83%
83%
80%
80%
83%
83%
Denotes advanced product release. Consult factory for product availability.
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
MECHANICAL DRAWING
2.00"
0.18"
(50.8mm)
0.700"(17.8mm)
0.500"(12.7mm)
(4.6mm)
3
1.200"(30.5mm)
4
0.800"(20.3mm)
1
2
DIA 0.040"
(1.0mm)
2.00"
(50.8mm)
BOTTOM VIEW
5
0.400"(10.2mm)
6
0
-0.40"(-10.2mm)
0.025" REF.
0
1.800"(45.7mm)
(0.6mm)
-0.10"(-2.5mm)
Thermal Impedance
Natural Convection
100 LFM
200 LFM
300 LFM
400 LFM
11.2
9.6
6.8
5.1
4.2
°C/W
°C/W
°C/W
°C/W
°C/W
Note:
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated for
specific application.
Pin
Function
1
2
3
4
5
6
+Vin
-Vin
+V out
+V out
-V out
-V out
2
0.40"
(10.2mm)
Tolerances
Inches:
.XX ± 0.020
.XXX ± 0.010
Pin:
± 0.002
(Millimeters)
.X ± 0.5
.XX ± 0.25
± 0.05
(Dimensions as listed unless otherwise
specified.)
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that
you prefer and add them to the model number. Example ordering options are located below the
options table.
OPTION
SUFFIX
APPLICABLE SERIES
Negative Logic
N
HAS, HBD, HBS, HES, LES, QBS,
QES, TES, TQD
Lucent Compatible Trim
T
HAS, HBD, HBS, HES, QBS, QES
Terminal Strip
TS
REMARKS
TTL “Low” Turns Module ON
TTL “High” Turns Module OFF
XWS, XWD, XWT
Trim
1
IAS, LES
Enable
2
IAD, IAS, LES, SMS
Trim and Enable
3
IAS, LES
Current Share
4
SMS
Headerless
Y
Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
Standard Pin Length is 0.180”
(4.6mm)
0.110” (2.8mm) Pin Length
8
All Units (Except SMS)
0.150” (3.8mm) Pin Length
9
All Units (Except SMS)
0.24” (6.1mm) Horizontal Heatsink
1H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.24” (6.1mm) Vertical Heatsink
1V
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.45” (11.4mm) Horizontal
Heatsink
2H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.45” (11.4mm) Vertical Heatsink
2V
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.95” (24.1mm) Horizontal
Heatsink
3H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.95” (24.1mm) Vertical Heatsink
3V
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and
0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
3
Similar pages