规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF948A SMD-6 MARKING 印 字： HDF6940 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-4-24 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDF948A S-6 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDF948A S-6 1. Package Dimension Marking：HDF6940 HD: Brand F : Filter 6 : SMD-6 940 : No. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 8 SAW FILTER HDF948A S-6 2.Maximum Rating Operation Temperature Range -40℃ to +85℃ Storage Temperature Range -40℃to +85℃ DC. Permissive Voltage 0 V DC. max. 3.1Electronic Characteristics Center Frequency Insertion Loss (In Fc +/- 3.75 MHz) Amplitude Ripple (In Fc +/- 3.75 MHz) Relative Attenuation 0.3 MHz ~ 875.0 MHz 875.0 MHz ~ 923.0MHz 973.0 MHz ~ 1030.0MHz 1030.0 MHz ~ 1550.0MHz Input/Output Impedance Unit Minimum Typical Maximum MHz - 948.75 - 4.0 1.0 4.5 2.0 dB dB dB 40 35 40 40 Ohms 50 40 50 45 50 - 3.2 Frequency Characteristics www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDF948A S-6 4. Test Circuit 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-3 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in table 1. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in table 1. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in table 1. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in table 1. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in table 1. 5-8 Lead fatigue www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER HDF948A S-6 5-8-1 Pulling test Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial Characteristics. 5-8-2 Bending test Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of thickness. This operation shall be done toward both direction. The device shall show no evidence of damage and shall 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER HDF948A S-6 Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW FILTER HDF948A S-6 [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 4.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.5 ±0.25 0.31 ±0.05 1.30 ±0.10 3.4 MAX. 3.4 MAX [Figure 2] [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8