ZETTLER AZ822 Subminiature dip relay Datasheet

AZ822
SUBMINIATURE
DIP RELAY
FEATURES
•
•
•
•
•
•
•
•
•
Low profile for compact board spacing
DC coils to 48 VDC
Life expectancy to 10 million operations
Standard PC 0.1" grid terminal spacing
Fits standard 16 pin IC socket
Epoxy sealed
Meets FCC Part 68.302 1500 V lightning surge
Meets FCC Part 68.304 1000 V dielectric
UL, CUR file E43203
CONTACTS
GENERAL DATA
Arrangement
DPDT (2 Form C)
Bifurcated crossbar contacts
Ratings
Resistive load:
Max. switched power:
60 W or 125 VA
Max. switched current:
2A
Max. switched voltage: 220 VDC* or 250 VAC
Life Expectancy
Mechanical
Electrical
Minimum operations
1 x 108
5 x 105 at 1 A 30 VDC
(see table for additional figures)
Operate Time (typical)
5 ms at nominal coil voltage
Release Time (typical)
2 ms at nominal coil voltage
(with no coil suppression)
Capacitance
Contact to contact: 1.2 pF
Contact set to contact set: 1.6 pF
Contact to coil: 1.5 pF
Bounce
(typical)
At 10 mA contact current
2 ms at operate N.O. side
3 ms at operate N.C. side
* Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
Rated Load
UL, CUR
1.0 A at 24 VDC
0.5 A at 120 VAC
Material
Silver palladium, gold clad
Resistance
< 50 milliohms initially
Dielectric Strength
1000 Vrms contact to coil
(at sea level for 1 min.) 1000 Vrms contact to contact
1000 Vrms between contact sets
Insulation Resistance
1000 megohms min. at 20°C, 500 VDC,
50% RH
Dropout
Greater than 5% of nominal coil voltage
Ambient Temperature
Operating
Storage
At nominal coil voltage
-55°C (-67°F) to 90°C (194°F)
-55°C (-67°F) to 105°C (221°F)
Vibration
0.062" (1.5 mm) DA at 10–55 Hz
Shock
20 g
Enclosure
P.B.T. polyester (UL94 V-0)
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
1. All values at 20°C (68°F).
Max. Solvent Temp.
80°C (176°F)
2. Relay may pull in with less than “Must Operate” value.
Max. Immersion Time
30 seconds
3. Relay adjustment may be affected if undue pressure is exerted
on relay case.
Weight
4.5 grams
4. Specifications subject to change without notice.
Packing unit in pcs
20 per plastic tube / 1000 per carton box
COIL
Power
At Pickup Voltage
(typical)
74 mW 3 - 12 V coils
98 mW 15 - 24 V coils
147 mW 48 V coils
Max. Continuous
Dissipation
0.94 W at 20°C (68°F)
Temperature Rise
15°C (27°F) at nominal coil voltage
Temperature
Max. 105°C (221°F)
NOTES
ZETTLER
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2004-08-22
China
AZ822
RELAY ORDERING DATA
COIL SPECIFICATIONS
Nominal Coil
VDC
3
ORDER NUMBER
Must Operate
VDC
2.1
Max. Continuous
VDC
7.5
Coil Resistance
Ohm ± 10%
60
AZ822–2C–3DSE
5
3.5
12.5
167
AZ822–2C–5DSE
6
9
4.2
6.3
15.0
22.5
240
540
AZ822–2C–6DSE
AZ822–2C–9DSE
12
8.4
30.0
960
AZ822–2C–12DSE
18
12.6
40.0
1,620
AZ822–2C–18DSE
24
16.8
52.9
2,880
AZ822–2C–24DSE
48
33.6
84.9
7,680
AZ822–2C–48DSE
MECHANICAL DATA
PC BOARD LAYOUT
8 x ø .03
[ø 0.8]
.047
(1.2) REF
.386
(9.8)
.787
(20)
.138
(3.5)
.047
(1.2) REF
0.1
(2.54)
.015
(0.38)
.472
(12)
Viewed toward terminals
WIRING DIAGRAM
.044
(1.11)
.300
(7.61)
.200
(5.07)
.200
(5.07)
(.020 ± .005)
(0.5 ± 0.13)
TYP
.010 ± .005
(0.25 ± 0.13)
TYP
1
4
6
8
16
13
11
9
Viewed toward terminals
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
TYPICAL CONTACT LIFE EXPECTANCY
Maximum Switching Capacity
NUMBER OF OPERATIONS
VOLTAGE
CURRENT
RESISTIVE
LOAD
1x 107
10.0
9.0
8.0
7.0
6.0
5.0
4.0
INDUCTIVE
LOAD
1 x 107
50 mV
1 mA
30 VDC
1A
5 x 105
15 x 104
30 VDC
0.7 A
1 x 106
3 x 105
30 VDC
0.3 A
3 x 106
1 x 106
60 VDC
0.5 A
5 x 105
—
60 VDC
0.3 A
1 x 106
—
60 VDC
0.2 A
106
—
.3
30 VAC
2A
5 x 105
15 x 104
.2
30 VAC
1.3 A
1 x 106
3 x 105
30 VAC
0.7 A
3 x 106
1 x 106
60 VAC
1A
5 x 105
15 x 104
60 VAC
0.7 A
1x
106
3 x 105
60 VAC
0.3 A
3 x 106
1 x 106
125 VAC
0.5 A
5 x 105
15 x 104
125 VAC
0.3 A
1 x 106
3 x 105
125 VAC
0.2 A
3 x 106
1 x 106
ZETTLER
2.0
AC resistive
1.0
.9
.8
.7
.6
.5
1000
400
500
600
700
800
900
300
200
100
50
60
70
80
90
40
20
.1
30
DC resistive
.4
10
3x
CURRENT
3.0
Contact Voltage (V)
NOTES: 1. Relays operated at nominal coil voltage.
2. Inductive load tests are at 0.7 power factor.
3. Table represents typical life figures and are not
guaranteed minimums.
electronics GmbH
Junkersstrasse 3, D-82178 Puchheim, Germany
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
[email protected]
www.ZETTLERelectronics.com
2004-08-22
China
Similar pages