PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com HIGH PERFORMANCE DIFFERENTIAL OSCILLATOR SERIES „DLPO-2“ 220.0—800.0 MHz FEATURES APPLICATIONS + + + + + + + + + + + + + + + 100% pin-to-pin drop-in replacement to quartz and MEMS based XO Differential Oscillator for Low Cost LVCMOS, LVPECL, LVDS and CML output signal possible Low Power Consumption Excellent low RMS phase jitter Excellent long time reliability Very tight frequency stability as low as ±10 ppm Outstanding long term aging Standard housings: 5.0x3.2; 7.0x5.0 mm Pb-free, RoHS and REACH compliant / MSL1@260°C Server, Router, RAID controller Gigabit Ethernet, 10 Gigabit Ethernet, Fiber Channel SATA / SAS,PCI-Express, Fully Buffered DIMM System clock, Networking and computing, etc. PIN DESCRIPTION PIN SYMBOL 1 OE/ST 2 NC TOP VIEW FUNCTIONALITY Input NA Standby or Output Enable pin for OUT+ and OUT-. OE: When High or Open : OUT+ and OUT- = active When Low : OUT+ and OUT- = High Impedance state ST: When High or Open : OUT+ and OUT- = active When Low : OUT+ and OUT- = High Impedance State OE/ST 1 6 VDD NC 2 5 OUT- GND 3 4 OUT+ Do not connect pin, leave it floating. 3 GND Power VDD Power Supply Ground. Connect to Ground 4 OUT+ Output 220 to 800 MHz programmable clock output. 5 OUT- Output 6 VDD Power Power Supply Voltage CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DC ELECTRICAL SPECIFICATIONS LVCMOS input, OE or ST pin, 3.3V ±10% or 2.5V ±10% or 1.8V ±5%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Input High Voltage VIH 70 – – %VDD CONDITION Input Low Voltage VIL – – 30 %VDD Input High Current IIH – – 10 µA OE or ST pin Input Low Current IIL -10 – – µA OE or ST pin Power Up Time Tpu – – 10 ms Time from minimum power supply voltage to the first cycle (Guaranteed no runt pulses) LVPECL Output, 3.3V ±10% or 2.5V ±10%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Supply Voltage VDD 2.97 3.3 3.63 V 2.25 2.5 2.75 V Supply Current IDD – 68 74 mA VDD = 3.3, Excluding Load Termination Current – 65 71 mA VDD = 2.5, Excluding Load Termination Current Output High Voltage VOH VDD-1.1 – VDD-0.7 V Output Low Voltage VOL VDD-2.0 – VDD-1.4 V Vswing 600 800 1000 mV Pk-Pk Output Voltage Swing CONDITION 50 Ohm termination to Vdd - 2.0V See Figure 1, 2. LVDS Output, 3.3V ±10% or 2.5V ±10%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Supply Voltage VDD 2.97 3.3 3.63 V 2.25 2.5 2.75 V Supply Current IDD – 73 79 mA VDD = 3.3, Excluding Load Termination Current – 70 76 mA VDD = 2.5, Excluding Load Termination Current VOD1 250 350 450 mV Swing Mode = Normal Single load termination. See Figure 4. ΔVOD1 – – 50 mV VOS1 – 1.2 – V ΔVOS1 – – 50 mV Differential Output Voltage VOD Magnitude Change Offset Voltage VOS Magnitude Change Differential Output Voltage VOD Magnitude Change Offset Voltage VOD2 500 700 900 mV ΔVOD2 – – 50 mV VOS2 – 1.2 – V VOS Magnitude Change ΔVOS2 – – 50 mV Differential Output Voltage VOD3 250 350 450 mV ΔVOD3 – – 50 mV VOS3 – 1.2 – V ΔVOS3 – – 50 mV VOD Magnitude Change Offset Voltage VOS Magnitude Change CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS CONDITION Swing Mode = High Single load termination. See Figure 4. Swing Mode = High Double load termination. See Figure 5. PAGE 2 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DC ELECTRICAL SPECIFICATIONS CML Output, 3.3V ±10% or 2.5V ±10% or 1.8V ±5%, -40 to 85°C PARAMETER Supply Voltage Supply Current SYMBOL MIN. TYP. MAX. UNIT VDD 2.97 3.3 3.63 V 2.25 2.5 2.75 V 1.71 1.8 1.89 V – 48 51 mA VDD = 3.3V – 47 50 mA VDD = 2.5V – 38 41 mA VDD = 1.8V – VDD IDD Output High Voltage VOH1 VDD-0.1 Output Low Voltage VOL1 VDD- Pk-Pk Output Voltage Swing 0.55 VDD- 0.425 VDD- 0.3 V 300 425 550 mV Output High Voltage VOH2 VDD-0.1 – VDD V Output Low Voltage VOL2 VDD- VDD- V Pk-Pk Output Voltage Swing VDD- 0.85 0.6 Vswing2 600 850 1100 mV Output High Voltage VOH3 VDD-0.1 – VDD V Output Low Voltage VOL3 VDD- VDD- V Pk-Pk Output Voltage Swing Vswing3 0.55 300 VDD- 0.425 425 CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS 0.3 550 Excluding Load Termination Current Swing Mode = Normal Single Load Termination See Figure 6. V Vswing1 1.1 CONDITION Swing Mode = High Single Load Termination See Figure 6. Swing Mode = High Double Load Termination See Figure 7. mV PAGE 3 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com AC ELECTRICAL SPECIFICATIONS LVPECL Output, 3.3V ±10%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -10 – +10 PPM -15 – +15 PPM -20 – +20 PPM +25 PPM -25 -50 CONDITION Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C +50 PPM Aging Fage – – 1 PPM Duty Cycle DC 45 – 55 % Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz Output Rise/Fall Time tR/tF 160 260 350 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.3 0.44 ps Fout= 212.5MHz @ BW: 1.875M Hz to10 MHz – 0.3 0.33 ps Fout= 312.5 MHz @ BW: 1.875M Hz to10 MHz – 0.3 0.34 ps Fout= 600 MHz @ BW: 1.875M Hz to10 MHz – 1.4 1.8 ps Fout= 212.5 MHz – 1.4 1.8 ps Fout= 312.5 MHz – 1.5 2.2 ps Fout= 600 MHz – 1.2 1.6 ps Fout= 800 MHz RMS Period Jitter PJ First year @ 25°C LVPECL Output, 2.5V ±10%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -10 – +10 PPM -15 – +15 PPM -20 – +20 PPM +25 PPM -25 -50 CONDITION Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C +50 PPM Aging Fage – – 1 PPM Duty Cycle DC 45 – 55 % Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz First year @ 25°C Output Rise/Fall Time tR/tF 160 260 350 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.3 0.44 ps Fout= 212.5MHz @ BW: 1.875MHz to10 MHz – 0.3 0.33 ps Fout= 312.5 MHz @ BW: 1.875MHz to10 MHz – 0.3 0.34 ps Fout= 600 MHz @ BW: 1.875MHz to10 MHz – 1.4 1.8 ps Fout= 212.5 MHz – 1.4 1.8 ps Fout= 312.5 MHz – 1.5 2.2 ps Fout= 600 MHz – 1.2 1.6 ps Fout= 800 MHz RMS Period Jitter PJ CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com AC ELECTRICAL SPECIFICATIONS LVDS Output, 3.3V ±10%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -10 – +10 PPM -15 – +15 PPM -20 – +20 PPM -25 – +25 PPM -50 – +50 PPM CoNdition Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C Aging Fage – – 1 PPM First year @ 25°C Duty Cycle DC 45 – 55 % Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz Output Rise/Fall Time tR/tF 240 310 420 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.4 0.8 ps Fout= 212.5MHz @ BW: 1.875M Hz to10 MHz – 0.3 0.6 ps Fout= 312.5 MHz @ BW: 1.875M Hz to10 MHz – 0.2 0.4 ps Fout= 600 MHz @ BW: 1.875M Hz to10 MHz – 1.8 2.5 ps Fout= 212.5 MHz – 1.7 2.4 ps Fout= 312.5 MHz – 1.7 2.5 ps Fout= 600 MHz – 1.5 2.2 ps Fout= 800 MHz SYMBOL MIN. TYP. MAX. UNIT Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -10 – +10 PPM -15 – +15 PPM -20 – RMS Period Jitter PJ LVDS Output, 2.5V ±10%, -40 to 85°C PARAMETER +20 PPM -25 +25 PPM -50 +50 PPM CONDITION Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C Aging Fage – – 1 PPM Duty Cycle DC 45 – 55 % First year @ 25°C Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz Output Rise/Fall Time tR/tF 240 310 420 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.4 0.8 ps Fout= 212.5MHz @ BW: 1.875MHz to10 MHz – 0.3 0.6 ps Fout= 312.5 MHz @ BW: 1.875MHz to10 MHz – 0.2 0.4 ps Fout= 600 MHz @ BW: 1.875MHz to10 MHz – 1.7 2.4 ps Fout= 212.5 MHz – 1.7 2.5 ps Fout= 312.5 MHz – 1.6 2.1 ps Fout= 600 MHz – 1.4 1.8 ps Fout= 800 MHz RMS Period Jitter PJ CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com AC ELECTRICAL SPECIFICATIONS CML Output, 3.3V ±10%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -10 – +10 PPM -15 – +15 PPM -20 – +20 PPM -25 +25 PPM -50 +50 PPM CONDITION Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C Aging Fage – – 1 PPM Duty Cycle DC 45 – 55 % First year @ 25°C Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz Output Rise/Fall Time tR/tF 270 350 470 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.47 0.53 ps Fout= 212.5MHz @ BW: 1.875M Hz to10 MHz – 0.32 0.42 ps Fout= 312.5 MHz @ BW: 1.875M Hz to10 MHz – 0.26 0.34 ps Fout= 600 MHz @ BW: 1.875M Hz to10 MHz – 1.7 2.1 ps Fout= 212.5 MHz – 1.7 2.1 ps Fout= 312.5 MHz – 1.7 2.2 ps Fout= 600 MHz – 1.4 1.8 ps Fout= 800 MHz RMS Period Jitter PJ CML, 2.5V ± 10%, -40 to 85°C Parameter Symbol Min. Typ. Max. Unit Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -10 – +10 PPM -15 – +15 PPM -20 – +20 PPM -25 +25 PPM -50 +50 PPM Condition Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C Aging Fage – – 1 PPM Duty Cycle DC 45 – 55 % First year @ 25°C Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz Output Rise/Fall Time tR/tF 270 350 470 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.47 0.53 ps Fout= 212.5MHz @ BW: 1.875MHz to10 MHz – 0.32 0.38 ps Fout= 312.5 MHz @ BW: 1.875MHz to10 MHz – 0.26 0.34 ps Fout= 600 MHz @ BW: 1.875MHz to10 MHz – 1.7 2.1 ps Fout= 212.5 MHz – 1.7 2.1 ps Fout= 312.5 MHz – 1.7 2.2 ps Fout= 600 MHz – 1.4 1.8 ps Fout= 800 MHz RMS Period Jitter PJ CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com AC ELECTRICAL SPECIFICATIONS CML, 1.8V ± 5%, -40 to 85°C PARAMETER SYMBOL MIN. TYP. MAX. UNIT Output Frequency Fout 220 – 800 MHz Frequency Stability Fstab -15 – +15 PPM -20 +20 PPM -25 – +25 PPM -50 +50 PPM CONDITION Inclusive of initial stability, operating temp., rated power supply voltage change, load change 0 to 70°C -20 to 70°C -40 to 85°C Aging Fage – – 1 PPM Duty Cycle DC 45 – 55 % First year @ 25°C Fout= 220 - 460 MHz, 490 - 610 MHz or 750 - 800 MHz 35 – 65 % Fout= 460.1 - 489.9 MHz or 610.1- 749.9 MHz Output Rise/Fall Time tR/tF 270 350 470 ps 20% to 80% RMS Phase Jitter (random) PHJ – 0.47 0.53 ps Fout= 212.5MHz @ BW: 1.875MHz to10 MHz – 0.32 0.42 ps Fout= 312.5 MHz @ BW: 1.875MHz to10 MHz – 0.26 0.34 ps Fout= 600 MHz @ BW: 1.875MHz to10 MHz – 1.9 2.3 ps Fout= 212.5 MHz – 1.8 2.2 ps Fout= 312.5 MHz – 1.7 2.3 ps Fout= 600 MHz – 1.6 1.9 ps Fout= 800 MHz RMS Period Jitter PJ CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS FIGURE 1. LVPECL AC COUPLED TYPICAL TERMINATION (LVPECL-0) VDD= 3.3V => R1 = 150 Ω VDD= 2.5V => R1 = 120 Ω VDD OUT+ Z0 = 50 Ω D+ 100nF Receiver Device Drive Device 100nF OUT- Z0 = 50 Ω R1 D- R1 50 Ω 50 Ω VTT FIGURE 2. LVPECL DC COUPLED TYPICAL TERMINATION WITH TERMINATION VOLTAGE (LVPECL-1) VDD OUT+ Z0 = 50 Ω D+ Receiver Device Drive Device OUT- Z0 = 50 Ω D50 Ω 50 Ω VTT = VDD - 2.0 FIGURE 3. LVPECL DC COUPLED TYPICAL TERMINATION WITHOUT TERMINATION VOLTAGE (LVPECL-1) VDD = 3.3V => R1 = R3 = 133 Ω and R2 = R4 = 82 Ω VDD = 2.5V => R1 = R3 = 250 Ω and R2 = R4 = 62.5 Ω VDD OUT+ VDD R1 R3 Z0 = 50 Ω D+ Drive Device OUT- Receiver Device Z0 = 50 Ω DR2 CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS R4 PAGE 8 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS FIGURE 4. LVDS SINGLE TERMINATION (LOAD TERMINATED) OUT+ Z0 = 50 Ω D+ Drive Device 100 Ω OUT- Receiver Device Z0 = 50 Ω D- FIGURE 5. LVDS DOUBLE TERMINATION (SOURCE + LOAD TERMINATED) OUT+ A Drive Device Z0 = 50 Ω B 100 Ω 100 Ω A OUT- Receiver Device B Z0 = 50 Ω D+ D- Note: For AC coupled operation, include/insert decoupling caps at points A or B FIGURE 6. CML SINGLE LOAD TERMINATION VDD OUT+ Z0 = 50 Ω D+ Receiver Device Drive Device OUT- Z0 = 50 Ω D50 Ω 50 Ω VDD ≤ VT ≤ 3.63V CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 9 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS FIGURE 7. CML DOUBLE LOAD TERMINATION OUT+ A Z0 = 50 Ω B D+ Receiver Device Driver Device A OUT- B Z0 = 50 Ω D- 50 Ω 50 Ω 50 Ω VDD ≤ VT1 ≤ 3.63V 50 Ω VDD ≤ VT2 ≤ 3.63V Notes: 1. For DC-coupled operation, VT1 = VT2 2. For AC coupled operation, include/insert decoupling caps at points A o r B 3. For AC-coupled operation with capacitors p laced at point A, VT2 sets the input common m ode of Receiver Device and need not to be related to VT1 CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 10 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0X 3.2 X 0.75 MM #2 #5 #4 #1 #2 #3 #3 1.20 2.20 #6 0.64 0.90 0.75±0.05 #1 2.54 2.54 #4 0.9 #5 0.8 5.0±0.10 3.2±0.10 #6 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0X 5.0 X 0.90 MM 2.30 5.08 #6 #5 #4 #2 #3 0.90±0.10 #1 #1 #2 #3 3.80 1.10 1.40 1.60 #4 1.47 #5 5.08 5.0±0.10 2.60 1.47 #6 7.0±0.10 1.60 No Connect or Connect to GND (recommended) Note: 1. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 11 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION OSCILLATOR FAMILY DLPO2 SUPPLY VOLTAGE FREQUENCY TEMPERATURE RANGE “18“ for 1.8V (CML only( “25“ for 2.5V “33“ for 3.3V SIGNALING TYPE 220.000000 MHz to 800.000000 MHz “C” for 0 +70°C “M” for -20 +70°C “W” for -40 +85°C “0” = LVPECL-0 (Figure 1) “1” = LVPECL-1 Figure 2, 3) “2” = LVDS “3” = CML “4” = LVCMOS DLPO2 33-5032-E-15-W-220.000MHz-T-1-N FREQUENCY STABILITY “10” for ±10 PPM “15” for ±15 PPM “20” for ±20 PPM “25” for ±25 PPM “50” for ±50 PPM PACKAGE SIZE PACKING METHOD “B“ for Bulks or Tubes “T” for Tape & Reel SWING SELECT FEATURE PIN 1 “5032” for 5.0 X 3.2 mm “7051” for 7.0 X 5.0 mm (with center-pad) “N” = Normal “H” = High (LVDS & CML only) “E” for OUTPUT ENABLE “S” for STANDBY EXAMPLE: DLPO233-5032-E-15-W-220.000MHz-T-1-N PLEASE INDICATE YOUR REQUIRED PARAMETERS FREQUENCY STABILITY VS. TEMPERATURE RANGE OPTIONS FREQUENCY TEMPERATURE STABILITY (PPM) RANGE ±10 ±15 ±20 ±25 ±50 SUPPLY VOLTAGE 1.8 V 2.5 V SIGNALING TYPE VS. SWING SELECT OPTIONS SIGNALING SWING SELECT TYPE 3.3 V C (0 to +70°C) – M (-20 to +70°C) – – – W (-40 to +85°C) C (0 to +70°C) – – – M (-20 to +70°C) – W (-40 to +85°C) – C (0 to +70°C) M (-20 to +70°C) W (-40 to +85°C) C (0 to +70°C) M (-20 to +70°C) W (-40 to +85°C) C (0 to +70°C) M (-20 to +70°C) W (-40 to +85°C) LVPECL-0 LVPECL-1 LVDS CML SUPPLY VOLTAGE 1.8 V 2.5 V 3.3 V Normal – – – – – High – Normal – High – Normal – High – Normal High SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 12 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com REFLOW SOLDER PROFILE PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 13 OF 13 I SPEC 01 I REV.00 I NOVEMBER 2014