PRELIMINARY PRELIMINARY DS1722 Digital Thermometer with SPI/3-Wire Interface www.dalsemi.com FEATURES Temperature measurements require no external components Measures temperatures from -55°C to +120°C. Fahrenheit equivalent is -67°F to +248°F Thermometer accuracy is ±2.0°C Thermometer resolution is configurable from 8 to 12 bits (1.0°C to 0.0625°C resolution) Data is read from/written to via a Motorola Serial Peripheral Interface (SPI) or standard 3-wire serial interface Wide analog power supply range (2.65V 5.5V) Separate digital supply allows for 1.8V logic Available in an 8-pin SOIC (150 mil), 8-pin uSOP, and flip chip package PIN ASSIGNMENT VDDD 1 8 VDDA CE 2 7 SERMODE SCLK 3 6 SDI GND 4 5 SDO 1* 8 VDDA CE 2 7 SERMODE SCLK 3 4 6 5 SDI VDDD GND DS1722S 8-Pin SOIC (150-mil) SDO DS1722U 8-PIN µ-SOP PIN DESCRIPTION SERMODE CE SCLK GND VDDA SDO SDI VDDD - Serial Interface Mode - Chip Enable - Serial Clock - Ground - Analog Supply Voltage - Serial Data Out - Serial Data In - Digital Supply Voltage DESCRIPTION The DS1722 Digital Thermometer and Thermostat with SPI/3-Wire Interface provides temperature readings which indicate the temperature of the device. No additional components are required; the device is truly a temperature-to-digital converter. Temperature readings are communicated from the DS1722 over a Motorola SPI interface or a standard 3-wire serial interface. The choice of interface standard is selectable by the user. For applications that require greater temperature resolution, the user can adjust the readout resolution from 8 to 12 bits. This is particularly useful in applications where thermal runaway conditions must be detected quickly. For application flexibility, the DS1722 features a wide analog supply rail of 2.65V - 5.5V. A separate digital supply allows a range of 1.8V to 5.5V. The DS1722 is available in an 8-pin SOIC (150-mil), 8-pin uSOP, and flip chip package. Applications for the DS1722 include personal computers/servers/workstations, cellular telephones, office equipment, or any thermally-sensitive system. 1 of 13 021500 DS1722 DETAILED PIN DESCRIPTION Table 1 SOIC SYMBOL PIN 1 VDDD PIN 2 CE PIN 3 SCLK PIN 4 GND PIN 5 SDO PIN 6 SDI PIN 7 SERMODE PIN 8 VDDA DESCRIPTION Digital Supply Voltage 1.8V-5.5V. Defines the top rails for the digital inputs and outputs. Chip Enable Must be asserted high for communication to take place for either the SPI or 3-wire interface. Serial Clock Input Used to synchronize data movement on the serial interface for either the SPI or 3-wire interface. Ground pin. Serial Data Output When SPI communication is selected, the SDO pin is the serial data output for the SPI bus. When 3-wire communication is selected, this pin must be tied to the SDI pin (the SDI and SDO pins function as a single I/O pin when tied together.) Serial Data Input When SPI communication is selected, the SDI pin is the serial data input for the SPI bus. When 3-wire communication is selected, this pin must be tied to the SDO pin (the SDI and SDO pins function as a single I/O pin when tied together.) Serial Interface Mode Input This pin selects which interface standard will be used: SPI when connected to VCC ; standard 3-wire when connected to GND. Analog Supply Voltage 2.65V – 5.5V input power pin. OVERVIEW A block diagram of the DS1722 is shown in Figure 1. The DS1722 consists of four major components: 1. Precision temperature sensor 2. Analog-to-digital converter 3. SPI/3-wire interface electronics 4. Data registers The factory-calibrated temperature sensor requires no external components. The DS1722 is in a powerconserving shutdown state upon power-up. After power-up, the user may alter the configuration register to place the device in a continuous temperature conversion mode or in a one-shot conversion mode. In the continuous conversion mode, the DS1722 continuously converts the temperature and stores the result in the temperature register. As conversions are performed in the background, reading the temperature register does not affect the conversion in progress. In the one-shot temperature conversion mode, the DS1722 will perform one temperature conversion, store the result in the temperature register, and then return to the shutdown state. This conversion mode is ideal for power sensitive applications. More information on the configuration register is contained in the “OPERATION-Programming” section. The temperature conversion results will have a default resolution of 9 bits. In applications where small incremental temperature changes are critical, the user can change the conversion resolution from 9 bits to 8, 10, 11, or 12. This is accomplished by programming the configuration register. Each additional bit of resolution approximately doubles the conversion time. 2 of 13 DS1722 The DS1722 can communicate using either a Motorola Serial Peripheral Interface (SPI) or standard 3wire interface. The user can select either communication standard through the SERMODE pin, tying it to VDDD for SPI and to ground for 3-wire. The device contains both an analog supply voltage and a digital supply voltage (VDDA and VDDD, respectively). The analog supply powers the device for operation while the digital supply provides the top rails for the digital inputs and outputs. The DS1722 was designed to be 1.8V Logic-Ready. DS1722 FUNCTIONAL BLOCK DIAGRAM Figure 1 OPERATION-Measuring Temperature The core of DS1722 functionality is its direct-to-digital temperature sensor. The DS1722 measures temperature through the use of an on-chip temperature measurement technique with an operating range from -55°=to +120°C. The device powers up in a power-conserving shutdown mode. After power-up, the DS1722 may be placed in a continuous conversion mode or in a one-shot conversion mode. In the continuous conversion mode, the device continuously computes the temperature and stores the most recent result in the temperature register at addresses 01h (LSB) and 02h (MSB). In the one-shot conversion mode, the DS1722 performs one temperature conversion and then returns to the shutdown mode, storing temperature in the temperature register. Details on how to change the setting after powerup are contained in the “OPERATION-Programming” section. 3 of 13 DS1722 The resolution of the temperature conversion is configurable (8, 9, 10, 11, or 12 bits), with 9-bit readings the default state. This equates to a temperature resolution of 1.0°C, 0.5°C, 0.25°C, 0.125°C, or 0.0625°C. Following each conversion, thermal data is stored in the thermometer register in two’s complement format; the information can be retrieved over the SPI or 3-wire interface with the address set to the temperature register, 01h (LSB) and then 02h (MSB). Table 2 describes the exact relationship of output data to measured temperature. The table assumes the DS1722 is configured for 12-bit resolution; if the device is configured in a lower resolution mode, those bits will contain 0s. The data is transmitted serially over the digital interface, MSb first for SPI communication and LSb first for 3-wire communication. The MSb of the temperature register contains the “sign” (S) bit, denoting whether the temperature is positive or negative. For Fahrenheit usage, a lookup table or conversion routine must be used. Temperature/Data Relationships Table 2 Address Location S 26 25 24 23 21 (unit = °C) MSb 2-1 22 2-2 2-3 2-4 0 20 02h LSb 0 0 0 01h TEMPERATURE +120°C DIGITAL OUTPUT (BINARY) 0111 1000 0000 0000 DIGITAL OUTPUT (HEX) 7800h +25.0625°C 0001 1001 0001 0000 1910h +10.125°C 0000 1010 0010 0000 0A20h +0.5°C 0000 0000 1000 0000 0080h 0°C 0000 0000 0000 0000 0000h -0.5°C 1111 1111 1000 0000 FF80h -10.125°C 1111 0101 1110 0000 F5E0h -25.0625°C 1110 0110 1111 0000 E6F0h -55°C 1100 1001 0000 0000 C900h OPERATION-Programming The area of interest in programming the DS1722 is the Configuration register. All programming is done via the SPI or 3-wire communication interface by selecting the appropriate address of the desired register location. Table 3 illustrates the addresses for the two registers (configuration and temperature) of the DS1722. Register Address Structure Table 3 Read Address 00h 01h 02h Write Address 80h No access No access 4 of 13 Active Register Configuration Temperature LSB Temperature MSB DS1722 CONFIGURATION REGISTER PROGRAMMING The configuration register is accessed in the DS1722 with the 00h address for reads and the 80h address for writes. Data is read from or written to the configuration register MSb first for SPI communication and LSb first for 3-wire communication. The format of the register is illustrated in Figure 2. The effect each bit has on DS1722 functionality is described below along with the power-up state of the bit. The entire register is volatile, and thus it will power-up in the default state. CONFIGURATION/STATUS REGISTER Figure 2 1 MSb 1 1 1SHOT R2 R1 R0 SD LSb 1SHOT = One-shot temperature conversion bit. If the SD bit is "1", (continuous temperature conversions are not taking place), a "1" written to the 1SHOT bit will cause the DS1722 to perform one temperature conversion and store the results in the temperature register at addresses 01h (LSB) and 02h (MSB). The bit will clear itself to "0" upon completion of the temperature conversion. The user has read/write access to the 1SHOT bit, although writes to this bit will be ignored if the SD bit is a "0", (continuous conversion mode). The power-up default of the one-shot bit is "0". R0, R1, R2 = Thermometer resolution bits. Table 4 below defines the resolution of the digital thermometer, based on the settings of these 3 bits. There is a direct tradeoff between resolution and conversion time, as depicted in the AC Electrical Characteristics. The user has read/write access to the R2, R1 and R0 bits and the power-up default state is R2="0", R1="0", and R0="1" (9-bit conversions). THERMOMETER RESOLUTION CONFIGURATION Table 4 R2 R1 0 0 0 0 0 1 0 1 1 x x=Don’t care. R0 0 1 0 1 x Thermometer Resolution 8-bit 9-bit 10-bit 11-bit 12-bit Max Conversion Time 0.075s 0.15s 0.3s 0.6s 1.2s SD = Shutdown bit. If SD is "0", the DS1722 will continuously perform temperature conversions and store the last completed result in the temperature register. If SD is changed to a "1", the conversion in progress will be completed and stored and then the device will revert to a low-power shutdown mode. The communication port remains active. The user has read/write access to the SD bit and the power-up default is "1" (shutdown mode). SERIAL INTERFACE The DS1722 offers the flexibility to choose between two serial interface modes. The DS1722 can communicate with the SPI interface or with a standard 3-wire interface. The interface method used is determined by the SERMODE pin. When this pin is connected to VDDD SPI communication is selected. When this pin is connected to ground, standard 3-wire communication is selected. SERIAL PERIPHERAL INTERFACE (SPI) The serial peripheral interface (SPI) is a synchronous bus for address and data transfer. The SPI mode of serial communication is selected by tying the SERMODE pin to VDDD. Four pins are used for the SPI. The four pins are the SDO (Serial Data Out), SDI (Serial Data In), CE (Chip Enable), and SCLK (Serial Clock). The DS1722 is the slave device in an SPI application, with the microcontroller being the master. 5 of 13 DS1722 The SDI and SDO pins are the serial data input and output pins for the DS1722, respectively. The CE input is used to initiate and terminate a data transfer. The SCLK pin is used to synchronize data movement between the master (microcontroller) and the slave (DS1722) devices. The shift clock (SCLK), which is generated by the microcontroller, is active only when CE is high and during address and data transfer to any device on the SPI bus. The inactive clock polarity is programmable in some microcontrollers. The DS1722 offers an important feature in that the level of the inactive clock is determined by sampling SCLK when CE becomes active. Therefore, either SCLK polarity can be accommodated. Input data (SDI) is latched on the internal strobe edge and output data (SDO) is shifted out on the shift edge (See Table 5 and Figure 3). There is one clock for each bit transferred. Address and data bits are transferred in groups of eight, MSB first. FUNCTION TABLE Table 5 MODE Disable Reset Write Read CE L H H SCLK Input Disabled CPOL=1* SDI Input Disabled Data Bit Latch CPOL=0 CPOL=1 X SDO High Z High Z Next data bit shift** CPOL=0 *CPOL is the “Clock Polarity” bit that is set in the control register of the microcontroller. ** SDO remains at High Z until eight bits of data are ready to be shifted out during a read. NOTE: CPHA bit polarity must be set to “1”. SERIAL CLOCK AS A FUNCTION OF MICROCONTROLLER CLOCK POLARITY (CPOL) Figure 3 CPOL=1 CE SHIFT INTERNAL STROBE SHIFT INTERNAL STROBE SCLK CPOL=0 CE SCLK NOTE: CPOL is a bit that is set in the microcontroller’s Control Register. 6 of 13 DS1722 ADDRESS AND DATA BYTES Address and data bytes are shifted MSB first into the serial data input (SDI) and out of the serial data output (SDO). Any transfer requires the address of the byte to specify a write or a read, followed by one or more bytes of data. Data is transferred out of the SDO for a read operation and into the SDI for a write operation. SPI SINGLE BYTE WRITE Figure 4 SPI SINGLE-BYTE READ Figure 5 The address byte is always the first byte entered after CE is driven high. The most significant bit (A7) of this byte determines if a read or write will take place. If A7 is "0", one or more read cycles will occur. If A7 is "1", one or more write cycles will occur. Data transfers can occur 1 byte at a time in multiple-byte burst mode. After CE is driven high an address is written to the DS1722. After the address, one or more data bytes can be written or read. For a singlebyte transfer, 1 byte is read or written and then CE is driven low (see Figures 4 and 5). For a multiplebyte transfer, however, multiple bytes can be read or written to the DS1722 after the address has been written (see Figure 6). A single-byte burst read/write will sequentially point through the memory map and will loop from 02h/82h to 00h/80h. 7 of 13 DS1722 SPI MULTIPLE BYTE BURST TRANSFER Figure 6 3-WIRE SERIAL DATA BUS The 3-wire communication mode operates similar to the SPI mode. However, in 3-wire mode, there is one bi-directional I/O instead of separate data in and data out signals. The 3-wire consists of the I/O (SDI and SDO pins tied together), CE, and SCLK pins. In 3-wire mode, each byte is shifted in LSB first unlike SPI mode where each byte is shifted in MSB first. As is the case with the SPI mode, an address byte is written to the device followed by a single data byte or multiple data bytes. Figure 7 illustrates a read and write cycle. Figure 8 illustrates a multiple byte burst transfer. In 3-wire mode, data is input on the rising edge of SCLK and output on the falling edge of SCLK. 3-WIRE SINGLE BYTE TRANSFER Figure 7 3-WIRE MULTIPLE BYTE BURST TRANSFER Figure 8 8 of 13 DS1722 ABSOLUTE MAXIMUM RATINGS* Voltage on V DD , Relative to Ground Voltage on any other pin, Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.3V to +6.0V -0.3V to +6.0V -55°C to +125°C -55°C to +125°C 260°C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. The Dallas Semiconductor DS1722 is built to the highest quality standards and manufactured for long term reliability. All Dallas Semiconductor devices are made using the same quality materials and manufacturing methods. However, the DS1722 is not exposed to environmental stresses, such as burn-in, that some industrial applications require. For specific reliability information on this product, please contact the factory in Dallas at (972) 371-4448. RECOMMENDED DC OPERATING CONDITIONS (-55°C to +120°C, 2.65V ≤ VDDA ≤5.5V) PARAMETER Analog Supply Voltage Digital Supply Voltage SYMBOL VDDA VDDD CONDITION MIN 2.65 1.8 TYP MAX UNITS NOTES 5.5 V 1 5.5 V 1 DC ELECTRICAL CHARACTERISTICS (-55°°C to +120°°C, 2.65V ≤ VDDA ≤=5.5V) PARAMETER Input Logic High SYMBOL VIH Input Logic Low VIL Logic 0 Output VOL Logic 1 Output VOH Input Resistance RI Active Current Shutdown Current ICC ICC CONDITION MIN 0.7 x VDDD TYP MAX UNITS NOTES V 1 0.2 x VDDD 0.2 x VDDD CE to GND SDI, SDO, SCLK to VDDD 2.65V≤ VDDA ≤=3.3V 3.3V≤VDDA≤5.5V 9 of 13 0.7 x VDDD 1 1 V 1 V 2 V 3 MΩ MΩ .5 0.5 1.0 mA µA µA 4 DS1722 ELECTRICAL CHARACTERISTICS: DIGITAL THERMOMETER (-55°°C to +120°°C, 2.65V ≤=VDDA ≤=5.5V) PARAMETER Thermometer Error Resolution Conversion Time SYMBOL TERR CONDITION -40°C to +85°C -55°C to +120°C MIN TYP 8 tCONVT 8-bit conversions 9-bit conversions 10-bit conversions 11-bit conversions 12-bit conversions 67.5 125 250 500 1000 MAX UNITS NOTES 8, 9 ±2.0 °C ±3.0 12 bits ms 75 150 300 600 1200 AC ELECTRICAL CHARACTERISTICS: 3-WIRE INTERFACE (-55°C to +120°C, 2.65V ≤=VDD ≤=5.5V) PARAMETER Data to SCLK Setup SCLK to Data Hold SCLK to Data Valid SCLK Low Time SCLK High Time SCLK Frequency SCLK Rise and Fall CE to SCLK Setup SCLK to CE Hold CE Inactive Time CE to Output High Z SCLK to Output High Z SYMBOL tDC tCDH tCDD tCL tCH tCLK tR , tF tCC tCCH tCWH tCDZ tCCZ CONDITION MIN 35 35 100 100 DC 400 100 400 TYP MAX UNITS ns ns 80 ns ns ns 5.0 MHz 200 ns ns ns ns 40 ns 40 ns TIMING DIAGRAM: 3-WIRE READ DATA TRANSFER Figure 9 10 of 13 NOTES 5, 6 5, 6 5, 6, 7 6 6 6 6 6 6 5, 6 5, 6 DS1722 TIMING DIAGRAM: 3-WIRE WRITE DATA TRANSFER Figure 10 *I/O is SDI and SDO tied together. AC ELECTRICAL CHARACTERISTICS: SPI Interface (-55°°C to +120°°C, 2.65V ≤=VDD ≤=5.5V) PARAMETER Data to SCLK Setup SCLK to Data Hold SCLK to Data Valid SCLK Low Time SCLK High Time SCLK Frequency SCLK Rise and Fall CE to SCLK Setup SCLK to CE Hold CE Inactive Time CE to Output High Z SYMBOL tDC tCDH tCDD tCL tCH tCLK tR , tF tCC tCCH tCWH tCDZ CONDITION MIN 35 35 TYP MAX 80 100 100 DC 5.0 200 400 100 400 40 TIMING DIAGRAM: SPI READ DATA TRANSFER Figure 11 11 of 13 UNITS ns ns ns ns ns MHz ns ns ns ns ns NOTES 5, 6 5, 6 5, 6, 7 6 6 6 6 6 6 5, 6 DS1722 TIMING DIAGRAM: SPI WRITE DATA TRANSFER Figure 12 *SCLK can be either polarity, timing shown for CPOL = 1. NOTES: 1. All voltages are referenced to ground. 2. Logic 0 voltages are specified at a sink current of 4 mA. 3. Logic 1 voltages are specified at a source current of 1 mA. 4. ICC specified with SCLK=VDDD and CE=GND. Typical ICC1 is 0.25 µA and ICC is 0.3 mA at 25°C and VDDD = 2.65V. 5. Measured at VIH =0.7 VDDD or VIL=0.2 VDDD and 10 ms maximum rise and fall time. 6. Measured with 50 pF load 7. Measured at VOH =0.7 VDDD or VOL =0.2 VDDD. Measured from the 50% point of SCLK to the VOH minimum of SDO. 8. Figure 13 shows mean thermometer error for a pre-characterization sample. Data covering a larger sample over the full temperature range is pending. 12 of 13 DS1722 TYPICAL DS1722 THERMOMETER ERROR 13 of 13