ON NB3M8304C Lvcmos/lvttl low skew fanout buffer Datasheet

NB3M8304C
3.3 V 200 MHz 1:4
LVCMOS/LVTTL Low Skew
Fanout Buffer
Description
The NB3M8304C is 1:4 fanout buffer with LVCMOS/LVTTL input
and output. The device supports the core supply voltage of 3.3 V (VDD
pin) and output supply voltage of 2.5 V or 3.3 V (VDDO pin). The
VDDO pin powers the four single ended LVCMOS/LVTTL outputs.
The NB3M8304C is Form, Fit and Function (pin to pin) compatible
to ICS8304 and ICS8304I. The NB3M8304C is qualified for industrial
operating temperature range.
Features
•
•
•
•
•
•
•
•
Input Clock Frequency up to 200 MHz
Low Output to Output Skew: 45 ps max
Low Part to Part Skew: 500 ps max
Low Additive RMS Phase Jitter
Input Clock Accepts LVCMOS/ LVTTL Levels
Operating Voltage:
♦ Core Supply: VDD = 3.3 V ±5%
♦ Output Supply: VDDO = 3.3 V ±5% or 2.5 V ±5%
Operating Temperature Range:
♦ Industrial: −40°C to +85°C
These Devices are Pb−Free and are RoHS Compliant
www.onsemi.com
MARKING
DIAGRAMS*
8
8
1
SOIC−8
D SUFFIX
CASE 751
A
L
Y
W
G
8304C
ALYWG
G
1
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information on page 5 of
this data sheet.
Figure 1. Block Diagram
© Semiconductor Components Industries, LLC, 2014
December, 2014 − Rev. 3
1
Publication Order Number:
NB3M8304C/D
NB3M8304C
Figure 2. Pin Configuration (Top View)
Table 1. PIN DESCRIPTION
Pin Number
Name
Type
Description
1
VDDO
Output Power
2
VDD
Input and Core Power
Input and Core Supply pin.
3
CLK
LVCMOS/LVTTL Input
Clock Input. Internally pull−down.
Clock output Supply pin.
4
GND
Ground
5, 6, 7, 8
Q[0:3]
LVCMOS/LVTTL Output
Supply Ground.
LVCMOS/LVTTL Clock output.
Table 2. MAXIMUM RATINGS
Symbol
Parameter
Condition
Min
Max
Unit
V
VDD, VDDO
Power Supply
−
4.6
VI
Input Voltage
−0.5
VDD + 0.5
V
Tstg
Storage Temperature
−65
+150
°C
θJA
Thermal Resistance (Junction−to−Ambient)
SOIC−8
θJC
Thermal Resistance (Junction to Case)
(Note 1)
Tsol
Wave Solder
MSL
Moisture Sensitivity
SOIC−8
°C/W
0 lfpm
500 lfpm
80
55
3 sec
Indefinite Time Out of Drypack
(Note 2)
12−17
°C/W
265
°C
Level 1
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. JEDEC standard multilayer board – 2S2P (2 signal, 2 power)
2. For additional information, see Application Note AND8003/D.
www.onsemi.com
2
NB3M8304C
Table 3. DC OPERATING CHARACTERISTICS (VDD = 3.3 V ±5%; TA = −40°C to +85°C)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
RIN
Input Pull−down Resistor (CLK Pin)
51
kW
CIN
Input Capacitance
4
pF
ROUT
Output Impedance (Note 3)
CPD
Power Dissipation Capacitance (per output)
VDD
Core Supply Voltage
5
7
VDD = VDDO = 3.465 V
15
3.135
IIH
Input High Current
VIN = VDD = 3.465 V
IIL
Input Low Current
VDD 3.465 V, VIN = 0.0 V
12
3.3
W
pF
3.465
V
150
mA
mA
−0.5
3. Outputs terminated with 50W to VDDO/2. See Figure 4 for supply considerations.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
Table 4. DC OPERATING CHARACTERISTICS (TA = −40°C to +85°C)
Symbol
Parameter
Condition
Min
Max
Unit
2.375
2.625
V
VDD = 3.3 V +5%, VDDO = 2.5 V +5%
VDDO
Output Supply Voltage
VOH
Output HIGH Voltage
VOL
Output LOW Voltage
IOH = −100 mA
2.2
IOH = −16 mA
2.1
50 W to VDDO/2
2.1
V
IOL = 16 mA
0.25
IOL = 100 mA
0.2
50 W to VDDO/2
0.5
V
VDD = VDDO = 3.3 V +5%
VDDO
Output Supply Voltage
VOH
Output HIGH Voltage
VOL
3.135
Output LOW Voltage
IOH = −16 mA
2.9
IOH = −100 mA
3
50 W to VDDO/2
2.6
3.465
V
V
IOL = 16 mA
0.25
IOL = 100 mA
0.15
50 W to VDDO/2
0.5
V
Table 5. DC OPERATING CHARACTERISTICS
(TA = −40°C to +85°C; VDD = VDDO = 3.3 V ±5%; VDD = 3.3 V ±5%, VDDO = 2.5 V ±5%)
Max
Unit
IDD
Quiescent Power Supply Current
No Load
15
mA
IDDO
Quiescent Power Supply Current
No Load
8
mA
VIH
Input HIGH Voltage
2
VDD + 0.3
V
VIL
Input LOW Voltage
−0.3
1.3
V
Symbol
Parameter
Condition
www.onsemi.com
3
Min
NB3M8304C
Table 6. AC CHARACTERISTICS (Note 4)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
200
MHz
3.3
ns
TA = −405C to +855C; VDD = 3.3 V +5%, VDDO = 3.3 V +5%
FIN
Input Frequency
tPLH
Propagation Delay (Note 5)
tSKEW
Fin = 200 MHz
1.9
Output to Output Skew(Note 6)
25
45
ps
Part to Part Skew (Note 6)
250
800
ps
tSKEWDC
Output Duty Cycle (see Figure 3)
Fin = 200 MHz
40
60
%
tr/tf
Output rise and fall times (Note 7)
30% to 70%, RS = 33 W,
CL = 10 pF
250
500
ps
200
MHz
3.7
ns
TA = −405C to +855C; VDD = 3.3 V +5%, VDDO = 2.5 V +5%
FIN
Input Frequency
tPLH
Propagation Delay (Note 5)
tSKEW
Fin = 200 MHz
2.2
Output to Output Skew(Note 6)
25
45
ps
Part to Part Skew (Note 6)
250
500
ps
tSKEWDC
Output Duty Cycle (see Figure 3)
Fin = 200 MHz
40
60
%
tr/tf
Output rise and fall times (Note 7)
30% to 70%, RS = 33 W,
CL = 10 pF
200
500
ps
4. Clock input with 50% duty cycle. Outputs terminated with 50 W to VDDO/2. See Figures 3 and 4.
5. Measured from VDD/2 of the input to VDDO/2 of the output.
6. Similar input conditions and the same supply voltages. Measured at VDDO /2. See Figures 3 and 4.
7. RS is Series Resistance and CL is Load Capacitance at the clock outputs.
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
www.onsemi.com
4
NB3M8304C
70%
70%
30%
30%
Figure 3. AC Reference Measurement
VDD
VDDO
ZO = 50 W
NB3M8304C
Qx
D
Receiver /
Scope
50 W
DUT
GND
Spec Condition:
TEST SETUP VDD:
TEST SETUP VDDO:
TEST SETUP DUT GND:
VDD = VDDO = 3.3 V ±5%
1.65 V ±5%
1.65 V ±5%
−1.65 V ±5%
VDD = 3.3 V ±5%;
VDDO = 2.5 V ±5%
2.05 V ±5%
1.25 V ±5%
−1.25 V ±5%
Figure 4. Output Driver Typical Device Evaluation and Termination Setup
ORDERING INFORMATION
Package
Shipping†
NB3M8304CDG
SOIC−8
(Pb−Free)
98 Units / Rail
NB3M8304CDR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
5
NB3M8304C
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
M
D
0.25 (0.010)
M
Z Y
S
X
S
J
SOLDERING FOOTPRINT*
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
6
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NB3M8304C/D
Similar pages