Microchip DSPIC33EP32GP503 16-bit microcontrollers and digital signal controller Datasheet

dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and
PIC24EPXXXGP/MC20X
16-bit Microcontrollers and Digital Signal Controllers (up to 512 KB Flash
and 48 KB SRAM) with High-Speed PWM, Op amps, and Advanced Analog
Operating Conditions
Timers/Output Compare/Input Capture
• 3.0V to 3.6V, -40ºC to +85ºC, DC to 70 MIPS
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 60 MIPS
• 12 general purpose timers:
- Five 16-bit and up to two 32-bit timers/counters
- Four OC modules configurable as timers/counters
- PTG module with two configurable timers/counters
- 32-bit Quadrature Encoder Interface (QEI) module
configurable as a timer/counter
• Four IC modules
• Peripheral Pin Select (PPS) to allow function remap
• Peripheral Trigger Generator (PTG) for scheduling
complex sequences
Core: 16-bit dsPIC33E/PIC24E CPU
•
•
•
•
•
Code-efficient (C and Assembly) architecture
Two 40-bit wide accumulators
Single-cycle (MAC/MPY) with dual data fetch
Single-cycle mixed-sign MUL plus hardware divide
32-bit multiply support
Clock Management
•
•
•
•
•
Communication Interfaces
0.9% internal oscillator
Programmable PLLs and oscillator clock sources
Fail-Safe Clock Monitor (FSCM)
Independent Watchdog Timer (WDT)
Fast wake-up and start-up
Power Management
•
•
•
•
Low-power management modes (Sleep, Idle, Doze)
Integrated Power-on Reset and Brown-out Reset
0.6 mA/MHz dynamic current (typical)
30 µA IPD current (typical)
High-Speed PWM
•
•
•
•
Up to three PWM pairs with independent timing
Dead time for rising and falling edges
7.14 ns PWM resolution
PWM support for:
- DC/DC, AC/DC, Inverters, PFC, Lighting
- BLDC, PMSM, ACIM, SRM
• Programmable Fault inputs
• Flexible trigger configurations for ADC conversions
• Two UART modules (17.5 Mbps)
- With support for LIN 2.0 protocols and IrDA®
• Two 4-wire SPI modules (15 Mbps)
• ECAN™ module (1 Mbaud) CAN 2.0B support
• Two I2C™ modules (up to 1 Mbaud) with SMBus
support
• PPS to allow function remap
• Programmable Cyclic Redundancy Check (CRC)
Direct Memory Access (DMA)
• 4-channel DMA with user-selectable priority arbitration
• UART, SPI, ADC, ECAN, IC, OC, and Timers
Input/Output
• Sink/Source 15 mA or 10 mA, pin-specific for
standard VOH/VOL, up to 22 or 14 mA, respectively
for non-standard VOH1
• 5V-tolerant pins
• Selectable open drain, pull-ups, and pull-downs
• Up to 5 mA overvoltage clamp current
• External interrupts on all I/O pins
Advanced Analog Features
• ADC module:
- Configurable as 10-bit, 1.1 Msps with four S&H or
12-bit, 500 ksps with one S&H
- Six analog inputs on 28-pin devices and up to 16
analog inputs on 64-pin devices
• Flexible and independent ADC trigger sources
• Up to three Op amp/Comparators with direct connection
to the ADC module:
- Additional dedicated comparator
- Programmable references with 32 voltage points
• Charge Time Measurement Unit (CTMU):
- Supports mTouch™ capacitive touch sensing
- Provides high-resolution time measurement (1 ns)
- On-chip temperature measurement
Qualification and Class B Support
• AEC-Q100 REVG (Grade 1 -40ºC to +125ºC) planned
• AEC-Q100 REVG (Grade 0 -40ºC to +150ºC) planned
• Class B Safety Library, IEC 60730
Debugger Development Support
•
•
•
•
In-circuit and in-application programming
Two program and two complex data breakpoints
IEEE 1149.2-compatible (JTAG) boundary scan
Trace and run-time watch
Packages
Type
SPDIP
SOIC
SSOP
Pin Count
28
28
28
I/O Pins
21
21
21
Contact Lead/Pitch
.100''
1.27
0.65
Dimensions
1.365x.240x.120'' 17.9x7.50x2.05 10.50x7.80x2
Note: All dimensions are in millimeters (mm) unless specified.
© 2011-2012 Microchip Technology Inc.
QFN-S
28
21
0.65
6x6x0.9
Preliminary
QFN
44
64
35
53
0.65
0.50
8x8x0.9 9x9x.9
VTLA
36
25
TQFP
44
35
44
35
0.50
5x5x0.5 6x6x0.5
64
53
0.50
10x10x1
DS70657E-page 1
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, AND
PIC24EPXXXGP/MC20X PRODUCT
FAMILIES
The device names, pin counts, memory sizes, and
peripheral availability of each device are listed in
Table 1 (General Purpose Families) and Table 2 (Motor
Control Families). Their pinout diagrams appear on the
following pages.
4
4
2
2
—
3
2
1
6
5
4
4
2
2
—
3
2
1
8
3/4
5
4
4
2
2
—
3
2
1
9
5
4
4
2
2
—
3
2
1
16
5
4
4
2
2
1
3
2
1
6
5
4
4
2
2
1
3
2
1
8
3/4
5
4
4
2
2
1
3
2
1
9
5
4
4
2
2
1
3
2
1
16
CTMU
PTG
I/O Pins
Pins
Packages
Op amps/Comparators
10-bit/12-bit ADC (Channels)
1024
256
32
PIC24EP512GP202
1024
512
48
PIC24EP32GP203
512
32
4
PIC24EP64GP203
1024
64
8
4
PIC24EP32GP204
512
32
PIC24EP64GP204
1024
64
8
PIC24EP128GP204
1024
128
16
PIC24EP256GP204
1024
256
32
PIC24EP512GP204
1024
512
48
PIC24EP64GP206
1024
64
8
PIC24EP128GP206
1024
128
16
PIC24EP256GP206
1024
256
32
PIC24EP512GP206
1024
512
48
dsPIC33EP32GP502
512
32
4
dsPIC33EP64GP502
1024
64
8
dsPIC33EP128GP502
1024
128
16
dsPIC33EP256GP502
1024
256
32
dsPIC33EP512GP502
1024
512
48
dsPIC33EP32GP503
512
32
4
dsPIC33EP64GP503
1024
64
8
dsPIC33EP32GP504
512
32
4
dsPIC33EP64GP504
1024
64
8
dsPIC33EP128GP504
1024
128
16
dsPIC33EP256GP504
1024
256
32
dsPIC33EP512GP504
1024
512
48
dsPIC33EP64GP506
1024
64
8
dsPIC33EP128GP506
1024
128
16
dsPIC33EP256GP506
1024
256
32
dsPIC33EP512GP506
1024
512
48
1:
2:
3:
4:
5
2/3(1) Yes
Yes
21
28
SPDIP,
SOIC,
SSOP(4),
QFN-S
Yes
Yes
25
36
VTLA
3/4
Yes
Yes
35
44
VTLA(4),
TQFP,
QFN
3/4
Yes
Yes
53
64
TQFP,
QFN
2/3(1) Yes
Yes
21
28
SPDIP,
SOIC,
SSOP(4),
QFN-S
Yes
Yes
25
36
VTLA
3/4
Yes
Yes
35
44
VTLA(4),
TQFP,
QFN
3/4
Yes
Yes
53
64
TQFP,
QFN
4
PIC24EP256GP202
Note
CRC Generator
16
I2C™
128
External Interrupts(3)
1024
ECAN™ Technology
8
PIC24EP128GP202
SPI(2)
64
UART
32
1024
Output Compare
512
PIC24EP64GP202
Input Capture
PIC24EP32GP202
16-bit/32-bit Timers
Remappable Peripherals
RAM (Kbyte)
Device
Program Flash Memory (Kbytes)
dsPIC33EPXXXGP50X and PIC24EPXXXGP20X GENERAL PURPOSE FAMILIES
Page Erase Size (Instructions)
TABLE 1:
On 28-pin devices, Comparator 4 does not have external connections. Refer to Section 25.0 “Op amp/Comparator Module” for details.
Only SPI2 is remappable.
INT0 is not remappable.
The SSOP and VTLA packages are not available for devices with 512 KB of memory.
DS70657E-page 2
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4
64
8
PIC24EP32MC204
512
32
4
PIC24EP64MC204
1024
64
8
PIC24EP128MC204
1024 128
16
PIC24EP256MC204
1024 256
32
PIC24EP512MC204
1024 512
48
PIC24EP64MC206
1024
64
8
PIC24EP128MC206
1024 128
16
PIC24EP256MC206
1024 256
32
PIC24EP512MC206
1024 512
48
dsPIC33EP32MC202
512
32
4
dsPIC33EP64MC202
1024
64
8
dsPIC33EP128MC202 1024 128
16
dsPIC33EP256MC202 1024 256
32
dsPIC33EP512MC202 1024 512
48
dsPIC33EP32MC203
512
32
4
dsPIC33EP64MC203
1024
64
8
dsPIC33EP32MC204
512
32
4
dsPIC33EP64MC204
1024
64
8
dsPIC33EP128MC204 1024 128
16
dsPIC33EP256MC204 1024 256
32
dsPIC33EP512MC204 1024 512
48
dsPIC33EP64MC206
64
8
dsPIC33EP128MC206 1024 128
1024
16
dsPIC33EP256MC206 1024 256
32
dsPIC33EP512MC206 1024 512
48
dsPIC33EP32MC502
512
32
4
dsPIC33EP64MC502
1024
64
8
dsPIC33EP128MC502 1024 128
16
dsPIC33EP256MC502 1024 256
32
dsPIC33EP512MC502 1024 512
48
dsPIC33EP32MC503
512
32
4
dsPIC33EP64MC503
1024
64
8
Note
1:
2:
3:
4:
5:
1
2
2
—
3
2
1
6
5
4
4
6
1
2
2
—
3
2
1
8
3/4
5
4
4
6
1
2
2
—
3
2
1
9
5
4
4
6
1
2
2
—
3
2
1
16
5
4
4
6
1
2
2
—
3
2
1
6
5
4
4
6
1
2
2
—
3
2
1
8
3/4
5
4
4
6
1
2
2
—
3
2
1
9
5
4
4
6
1
2
2
—
3
2
1
16
5
4
4
6
1
2
2
1
3
2
1
6
5
4
4
6
1
2
2
1
3
2
1
8
Op amps/Comparators
6
2/3(1) Yes Yes
21
28
SPDIP,
SOIC,
SSOP(5),
QFN-S
Yes Yes
25
36
VTLA
3/4
Yes Yes
35
44
VTLA(5),
TQFP,
QFN
3/4
Yes Yes
53
64
TQFP,
QFN
2/3(1) Yes Yes
21
28
SPDIP,
SOIC,
SSOP(5),
QFN-S
Yes Yes
25
36
VTLA
3/4
Yes Yes
35
44
VTLA(5),
TQFP,
QFN
3/4
Yes Yes
53
64
TQFP,
QFN
2/3(1) Yes Yes
21
28
SPDIP,
SOIC,
SSOP(5),
QFN-S
25
36
VTLA
3/4
CTMU
Packages
32
1024
4
Pins
512
PIC24EP64MC203
4
I/O Pins
PIC24EP32MC203
5
PTG
48
10-bit/12-bit ADC (Channels)
32
1024 512
CRC Generator
1024 256
PIC24EP512MC202
I2C™
PIC24EP256MC202
External Interrupts(3)
16
ECAN™ Technology
1024 128
SPI(2)
PIC24EP128MC202
UART
8
Quadrature Encoder Interface
4
64
Motor Control PWM(4)
(Channels)
32
1024
Output Compare
512
PIC24EP64MC202
Input Capture
PIC24EP32MC202
16-bit/32-bit Timers
Remappable Peripherals
RAM (Kbytes)
Device
Program Flash Memory (Kbytes)
dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X MOTOR CONTROL
FAMILIES
Page Erase Size (Instructions)
TABLE 2:
Yes Yes
On 28-pin devices, Comparator 4 does not have external connections. Refer to Section 25.0 “Op amp/Comparator Module” for details.
Only SPI2 is remappable.
INT0 is not remappable.
Only the PWM Faults are remappable.
The SSOP and VTLA packages are not available for devices with 512 KB of memory.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 3
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pins
Packages
48
1:
2:
3:
4:
5:
I/O Pins
dsPIC33EP512MC506 1024 512
PTG
32
CTMU
dsPIC33EP256MC506 1024 256
Op amps/Comparators
8
16
Note
1024
10-bit/12-bit ADC (Channels)
dsPIC33EP64MC506
CRC Generator
64
dsPIC33EP128MC506 1024 128
I2C™
48
External Interrupts(3)
32
dsPIC33EP512MC504 1024 512
ECAN™ Technology
dsPIC33EP256MC504 1024 256
SPI(2)
16
UART
dsPIC33EP128MC504 1024 128
Quadrature Encoder Interface
4
8
Motor Control PWM(4)
(Channels)
32
64
Input Capture
512
1024
Output Compare
dsPIC33EP32MC504
dsPIC33EP64MC504
16-bit/32-bit Timers
Remappable Peripherals
RAM (Kbytes)
Device
Program Flash Memory (Kbytes)
dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X MOTOR CONTROL
FAMILIES (CONTINUED)
Page Erase Size (Instructions)
TABLE 2:
5
4
4
6
1
2
2
1
3
2
1
9
3/4
Yes Yes
35
44
VTLA(5),
TQFP,
QFN
5
4
4
6
1
2
2
1
3
2
1
16
3/4
Yes Yes
53
64
TQFP,
QFN
On 28-pin devices, Comparator 4 does not have external connections. Refer to Section 25.0 “Op amp/Comparator Module” for details.
Only SPI2 is remappable.
INT0 is not remappable.
Only the PWM Faults are remappable.
The SSOP and VTLA packages are not available for devices with 512 KB of memory.
DS70657E-page 4
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams
= Pins are up to 5V tolerant
28-Pin SPDIP/SOIC/SSOP
MCLR
1
28
AVDD
AN0/OA2OUT/RA0
2
27
AVSS
3
26
RPI47/T5CK/RB15
4
25
RPI46/T3CK/RB14
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
5
PGEC1/AN4/C1IN1+/RPI34/RB2
6
PGED1/AN5/C1IN1-/RP35/RB3
7
VSS
8
OSC1/CLKI/RA2
9
OSC2/CLKO/RA3
10
RP36/RB4
11
CVREF2O/RP20/T1CK/RA4
dsPIC33EPXXXGP502
PIC24EPXXXGP202
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
24
RPI45/CTPLS/RB13
23
RPI44/RB12
22
TDI/RP43/RB11
21
TDO/RP42/RB10
20
VCAP
19
VSS
18
TMS/ASDA1/SDI1/RP41/RB9
12
17
TCK/CVREF1O/ASCL1/SDO1/RP40/T4CK/RB8
VDD
13
16
SCK1/RP39/INT0/RB7
PGED2/ASDA2/RP37/RB5
14
15
PGEC2/ASCL2/RP38/RB6
AVDD
1
28
2
27
AVSS
AN1/C2IN1+/RA1
3
26
RPI47/PWM1L/T5CK/RB15
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
4
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
5
PGEC1/AN4/C1IN1+/RPI34/RB2
6
PGED1/AN5/C1IN1-/RP35/RB3
7
VSS
8
OSC1/CLKI/RA2
9
OSC2/CLKO/RA3
10
FLT32/RP36/RB4
11
CVREF2O/RP20/T1CK/RA4
12
VDD
PGED2/ASDA2/RP37/RB5
dsPIC33EPXXXMC202/502
PIC24EPXXXMC202
MCLR
AN0/OA2OUT/RA0
25
RPI46/PWM1H/T3CK/RB14
24
RPI45/PWM2L/CTPLS/RB13
23
RPI44/PWM2H/RB12
22
TDI/RP43/PWM3L/RB11
21
TDO/RP42/PWM3H/RB10
20
VCAP
19
VSS
18
TMS/ASDA1/SDI1/RP41/RB9
17
TCK/CVREF1O/ASCL1/SDO1/RP40/T4CK/RB8
13
16
SCK1/RP39/INT0/RB7
14
15
PGEC2/ASCL2/RP38/RB6
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 5
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
28-Pin QFN-S(3)
RPI46/T3CK/RB14
RPI47/T5CK/RB15
AVSS
AVDD
MCLR
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
= Pins are up to 5V tolerant
28 27 26 25 24 23 22
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
1
21
RPI45/CTPLS/RB13
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
2
20
RPI44/RB12
PGEC1/AN4/C1IN1+/RPI34/RB2
3
19
TDI/RP43/RB11
PGED1/AN5/C1IN1-/RP35/RB3
4
18
TDO/RP42/RB10
VSS
5
17
VCAP
OSC1/CLKI/RA2
6
16
VSS
OSC2/CLKO/RA3
7
15
TMS/ASDA1/SDI1/RP41/RB9
TCK/CVREF1O/ASCL1/SDO1/RP40/T4CK/RB8
SCK1/RP39/INT0/RB7
PGEC2/ASCL2/RP38/RB6
RP36/RB4
10 11 12 13 14
VDD
9
PGED2/ASDA2/RP37/RB5
8
CVREF2O/RP20/T1CK/RA4
dsPIC33EPXXXGP502
PIC24EPXXXGP202
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70657E-page 6
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
28-Pin QFN-S(3)
RPI46/PWM1H/T3CK/RB14
RPI47/PWM1L/T5CK/RB15
AVSS
AVDD
MCLR
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
= Pins are up to 5V tolerant
28 27 26 25 24 23 22
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
1
21
RPI45/PWM2L/CTPLS/RB13
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
2
20
RPI44/PWM2H/RB12
PGEC1/AN4/C1IN1+/RPI34/RB2
3
19
TDI/RP43/PWM3L/RB11
PGED1/AN5/C1IN1-/RP35/RB3
dsPIC33EPXXXMC202/502
4
18
PIC24EPXXXMC202
TDO/RP42/PWM3H/RB10
VCAP
16
VSS
OSC2/CLKO/RA3
7
15
TMS/ASDA1/SDI1/RP41/RB9
TCK/CVREF1O/ASCL1/SDO1/RP40/T4CK/RB8
SCK1/RP39/INT0/RB7
10 11 12 13 14
PGEC2/ASCL2/RP38/RB6
9
PGED2/ASDA2/RP37/RB5
8
VDD
17
6
CVREF2O/RP20/T1CK/RA4
5
FLT32/RP36/RB4
VSS
OSC1/CLKI/RA2
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 7
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
36-Pin VTLA(3)
MCLR
AVDD
AVSS
RPI47/T5CK/RB15
RPI46/T3CK/RB14
35
AN0/OA2OUT/RA0
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
36
AN1/C2IN1+/RA1
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
= Pins are up to 5V tolerant
33
32
31
30
29
28
27
RPI45/CTPLS/RB13
1
26
RPI44/RB12
2
25
TDI/RP43/RB11
AN6/OA3OUT/C4IN1+/OCFB/RC0
3
24
TDO/RP42/RB10
AN7/C3IN1-/C4IN1-/RC1
4
23
VDD
VDD
5
22
VCAP
VSS
6
21
VSS
OSC1/CLKI/RA2
7
20
RP56/RC8
OSC2/CLKO/RA3
8
19
TMS/ASDA1/SDI1/RP41/RB9
SDA2/RPI24/RA8
9
14
15
16 17
18
PGEC2/ASCL2/RP38/RB6
TCK/CVREF1O/ASCL1/SDO1/RP40/T4CK/RB8
SCK1/RP39/INT0/RB7
13
PGED2/ASDA2/RP37/RB5
12
VDD
11
VSS
10
VDD
dsPIC33EP32GP503
dsPIC33EP64GP503
PIC24EP32GP203
PIC24EP64GP203
CVREF2O/RP20/T1CK/RA4
PGED1/AN5/C1IN1-/RP35/RB3
34
SCL2/RP36/RB4
PGEC1/AN4/C1IN1+/RPI34/RB2
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70657E-page 8
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
36-Pin VTLA(3)
AVDD
AVSS
RPI47/PWM1L/T5CK/RB15
RPI46/PWM1H/T3CK/RB14
34
MCLR
35
AN0/OA2OUT/RA0
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
36
AN1/C2IN1+/RA1
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
= Pins are up to 5V tolerant
33
32
31
30
29
28
27
RPI45/PWM2L/CTPLS/RB13
PGEC1/AN4/C1IN1+/RPI34/RB2
1
26
RPI44/PWM2H/RB12
PGED1/AN5/C1IN1-/RP35/RB3
2
25
TDI/RP43/PWM3L/RB11
AN6/OA3OUT/C4IN1+/OCFB/RC0
3
24
TDO/RP42/PWM3H/RB10
AN7/C3IN1-/C4IN1-/RC1
4
VDD
5
VSS
6
OSC1/CLKI/RA2
7
OSC2/CLKO/RA3
8
SDA2/RPI24/RA8
9
13
14
15
16 17
18
SCK1/RP39/INT0/RB7
12
TCK/CVREF1O/ASCL1/SDO1/RP40/T4CK/RB8
TMS/ASDA1/SDI1/RP41/RB9
11
PGEC2/ASCL2/RP38/RB6
19
10
PGED2/ASDA2/RP37/RB5
RP56/RC8
VDD
VSS
20
VDD
VCAP
21
VSS
VDD
CVREF2O/RP20/T1CK/RA4
23
22
FLT32/SCL2/RP36/RB4
dsPIC33EP32MC203/503
dsPIC33EP64MC203/503
PIC24EP32MC203
PIC24EP64MC203
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 9
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
= Pins are up to 5V tolerant
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RP39/INT0/RB7
PGEC2/ASCL2/RP38/RB6
PGED2/ASDA2/RP37/RB5
VDD
VSS
SCL1/RPI53/RC5
SDA1/RPI52/RC4
SCK1/RPI51/RC3
SDI1/RPI25/RA9
CVREF2O/SDO1/RP20/T1CK/RA4
44
43
42
41
40
39
38
37
36
35
34
44-Pin TQFP
TMS/ASDA1/RP41/RB9
1
33
SCL2/RP36/RB4
RP54/RC6
2
32
SDA2/RPI24/RA8
RP55/RC7
3
31
OSC2/CLKO/RA3
RP56/RC8
4
30
OSC1/CLKI/RA2
RP57/RC9
5
29
VSS
dsPIC33EPXXXGP504
PIC24EPXXXGP204
20
21
22
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
AVDD
19
PGEC1/AN4/C1IN1+/RPI34/RB2
18
23
MCLR
11
AN0/OA2OUT/RA0
PGED1/AN5/C1IN1-/RP35/RB3
RPI45/CTPLS/RB13
17
RPI44/RB12
24
16
AN6/OA3OUT/C4IN1+/OCFB/RC0
10
AVSS
AN7/C3IN1-/C4IN1-/RC1
25
15
26
9
RPI47/T5CK/RB15
8
RP43/RB11
14
RP42/RB10
RPI46/T3CK/RB14
AN8/C3IN1+/U1RTS/BCLK1/RC2
13
VDD
27
12
28
7
TDI/RA7
6
VCAP
TDO/RA10
VSS
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
DS70657E-page 10
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
= Pins are up to 5V tolerant
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RP39/INT0/RB7
PGEC2/ASCL2/RP38/RB6
PGED2/ASDA2/RP37/RB5
VDD
VSS
SCL1/RPI53/RC5
SDA1/RPI52/RC4
SCK1/RPI51/RC3
SDI1/RPI25/RA9
CVREF2O/SDO1/RP20/T1CK/RA4
44
43
42
41
40
39
38
37
36
35
34
44-Pin TQFP
TMS/ASDA1/RP41/RB9
1
33
FLT32/SCL2/RP36/RB4
RP54/RC6
2
32
SDA2/RPI24/RA8
RP55/RC7
3
31
OSC2/CLKO/RA3
RP56/RC8
4
30
OSC1/CLKI/RA2
RP57/RC9
5
29
VSS
VSS
6
VCAP
dsPIC33EPXXXMC204/504
PIC24EPXXXMC204
18
19
20
21
22
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
PGEC1/AN4/C1IN1+/RPI34/RB2
17
23
AVDD
11
MCLR
PGED1/AN5/C1IN1-/RP35/RB3
RPI45/PWM2L/CTPLS/RB13
16
RPI44/PWM2H/RB12
24
AVSS
AN6/OA3OUT/C4IN1+/OCFB/RC0
10
15
AN7/C3IN1-/C4IN1-/RC1
25
RPI47/PWM1L/T5CK/RB15
26
9
14
8
RP43/PWM3L/RB11
RPI46/PWM1H/T3CK/RB14
RP42/PWM3H/RB10
13
AN8/C3IN1+/U1RTS/BCLK1/FLT3/RC2
12
27
TDI/RA7
VDD
7
TDO/RA10
28
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 11
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
44-Pin VTLA(3)
CVREF2O/SDO1/RP20/T1CK/RA4
SDI1/RPI25/RA9
SCK1/RPI51/RC3
SDA1/RPI52/RC4
SCL1/RPI53/RC5
VDD
VSS
PGED2/ASDA2/RP37/RB5
PGEC2/ASCL2/RP38/RB6
RP39/INT0/RB7
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
= Pins are up to 5V tolerant
44 43 42 41 40 39 38 37 36 35 34 33
SCL2/RP36/RB4
TMS/ASDA1/RP41/RB9
1
32
SDA2/RPI24/RA8
RP54/RC6
2
31
OSC2/CLKO/RA3
RP55/RC7
3
30
OSC1/CLKI/RA2
RP56/RC8
4
29
VSS
RP57/RC9
5
VSS
6
dsPIC33EPXXXGP504
PIC24EPXXXGP204
28
VDD
27
AN8/C3IN1+/U1RTS/BCLK1/RC2
VCAP
7
26
AN7/C3IN1-/C4IN1-/RC1
RP42/RB10
8
25
AN6/OA3OUT/C4IN1+/OCFB/RC0
RP43/RB11
9
24
PGED1/AN5/C1IN1-/RP35/RB3
RPI44/RB12 10
23
PGEC1/AN4/C1IN1+/RPI34/RB2
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
AN1/C2IN1+/RA1
AN0/OA2OUT/RA0
AVDD
MCLR
AVSS
RPI47/T5CK/RB15
RPI46/T3CK/RB14
TDI/RA7
TDO/RA10
RPI45/CTPLS/RB13 11 12 13 14 15 16 17 18 19 20 21 22
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70657E-page 12
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
44-Pin VTLA(3)
CVREF2O/SDO1/RP20/T1CK/RA4
SDI1/RPI25/RA9
SCK1/RPI51/RC3
SDA1/RPI52/RC4
SCL1/RPI53/RC5
VSS
VDD
PGED2/ASDA2/RP37/RB5
PGEC2/ASCL2/RP38/RB6
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RP39/INT0/RB7
= Pins are up to 5V tolerant
44 43 42 41 40 39 38 37 36 35 34 33
FLT32/SCL2/RP36/RB4
TMS/ASDA1/RP41/RB9
1
32
SDA2/RPI24/RA8
RP54/RC6
2
31
OSC2/CLKO/RA3
RP55/RC7
3
30
OSC1/CLKI/RA2
RP56/RC8
4
29
VSS
RP57/RC9
5
VSS
6
dsPIC33EPXXXMC204/504
PIC24EPXXXMC204
28
VDD
27
AN8/C3IN1+/U1RTS/BCLK1/FLT3/RC2
VCAP
7
26
AN7/C3IN1-/C4IN1-/RC1
RP42/PWM3H/RB10
8
25
AN6/OA3OUT/C4IN1+/OCFB/RC0
RP43/PWM3L/RB11
9
24
PGED1/AN5/C1IN1-/RP35/RB3
RPI44/PWM2H/RB12 10
23
PGEC1/AN4/C1IN1+/RPI34/RB2
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
AN1/C2IN1+/RA1
MCLR
AN0/OA2OUT/RA0
AVDD
AVSS
RPI47/PWM1L/T5CK/RB15
TDI/RA7
RPI46/PWM1H/T3CK/RB14
TDO/RA10
RPI45/PWM2L/CTPLS/RB13 11 12 13 14 15 16 17 18 19 20 21 22
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 13
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
44-Pin QFN(3)
CVREF2O/SDO1/RP20/T1CK/RA4
SDI1/RPI25/RA9
SCK1/RPI51/RC3
SDA1/RPI52/RC4
SCL1/RPI53/RC5
VSS
VDD
PGED2/ASDA2/RP37/RB5
PGEC2/ASCL2/RP38/RB6
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RP39/INT0/RB7
= Pins are up to 5V tolerant
44 43 42 41 40 39 38 37 36 35 34
TMS/ASDA1/RP41/RB9
1
33
SCL2/RP36/RB4
RP54/RC6
2
32
SDA2/RPI24/RA8
RP55/RC7
3
31
OSC2/CLKO/RA3
RP56/RC8
4
30
OSC1/CLKI/RA2
RP57/RC9
5
29
VSS
VSS
6
dsPIC33EPXXXGP504
PIC24EPXXXGP204
28
VDD
VCAP
7
27
AN8/C3IN1+/U1RTS/BCLK1/RC2
RP42/RB10
8
26
AN7/C3IN1-/C4IN1-/RC1
RP43/RB11
9
25
AN6/OA3OUT/C4IN1+/OCFB/RC0
RPI44/RB12
10
24
PGED1/AN5/C1IN1-/RP35/RB3
RPI45/CTPLS/RB13
11
23
PGEC1/AN4/C1IN1+/RPI34/RB2
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
AN1/C2IN1+/RA1
AN0/OA2OUT/RA0
MCLR
AVDD
AVSS
RPI47/T5CK/RB15
RPI46/T3CK/RB14
TDI/RA7
TDO/RA10
12 13 14 15 16 17 18 19 20 21 22
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70657E-page 14
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
44-Pin QFN(3)
CVREF2O/SDO1/RP20/T1CK/RA4
SDI1/RPI25/RA9
SCK1/RPI51/RC3
SDA1/RPI52/RC4
SCL1/RPI53/RC5
VSS
VDD
PGED2/ASDA2/RP37/RB5
PGEC2/ASCL2/RP38/RB6
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RP39/INT0/RB7
= Pins are up to 5V tolerant
44 43 42 41 40 39 38 37 36 35 34
TMS/ASDA1/RP41/RB9
1
33
FLT32/SCL2/RP36/RB4
RP54/RC6
2
32
SDA2/RPI24/RA8
RP55/RC7
3
31
OSC2/CLKO/RA3
RP56/RC8
4
30
OSC1/CLKI/RA2
RP57/RC9
5
29
VSS
VSS
6
28
VDD
dsPIC33EPXXXMC204/504
PIC24EPXXXMC204
VCAP
7
27
AN8/C3IN1+/U1RTS/BCLK1/FLT3/RC2
RP42/PWM3H/RB10
8
26
AN7/C3IN1-/C4IN1-/RC1
RP43/PWM3L/RB11
9
25
AN6/OA3OUT/C4IN1+/OCFB/RC0
RPI44/PWM2H/RB12
10
24
PGED1/AN5/C1IN1-/RP35/RB3
RPI45/PWM2L/CTPLS/RB13
11
23
PGEC1/AN4/C1IN1+/RPI34/RB2
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
AN1/C2IN1+/RA1
MCLR
AN0/OA2OUT/RA0
AVDD
AVSS
RPI47/PWM1L/T5CK/RB15
RPI46/PWM1H/T3CK/RB14
TDI/RA7
TDO/RA10
12 13 14 15 16 17 18 19 20 21 22
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0
“I/O Ports” for more information.
3: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 15
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
= Pins are up to 5V tolerant
RPI45/CTPLS/RB13
RPI44/RB12
RP43/RB11
RP42/RB10
RP97/RF1
RPI96/RF0
VDD
VCAP
RP57/RC9
RD6
RD5
RP56/RC8
RP55/RC7
RP54/RC6
TMS/ASDA1/RP41/RB9
62
61
60
59
58
57
56
55
54
53
52
51
50
49
TDO/RA10
63
48
47
46
4
5
6
7
8
9
10
11
12
45
44
43
42
41
40
39
38
37
dsPIC33EP64GP506
dsPIC33EP128GP506
dsPIC33EP256GP506
dsPIC33EP512GP506
PIC24EP64GP206
PIC24EP128GP206
PIC24EP256GP206
PIC24EP512GP206
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AVDD
AVSS
AN6/OA3OUT/C4IN1+/OCFB/RC0
AN7/C3IN1-/C4IN1-/RC1
AN8/C3IN1+/U1RTS/BCLK1/RC2
AN11/C1IN2-(3)/U1CTS/RC11
VSS
VDD
AN12/C2IN2-(3)/U2RTS/BCLK2/RE12
AN13/C3IN2-(3)/U2CTS/RE13
AN14/RPI94/RE14
AN15/RPI95/RE15
SDA2/RPI24/RA8
SCL2/RP36/RB4
36
35
34
33
17
13
14
15
16
PGED1/AN5/C1IN1-/RP35/RB3
VDD
AN10/RPI28/RA12
AN9/RPI27/RA11
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
1
2
3
PGEC1/AN4/C1IN1+/RPI34/RB2
TDI/RA7
RPI46/T3CK/RB14
RPI47/T5CK/RB15
RP118/RG6
RPI119/RG7
RP120/RG8
MCLR
RPI121/RG9
VSS
64
64-Pin TQFP
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RC13
RP39/INT0/RB7
RPI58/RC10
PGEC2/ASCL2/RP38/RB6
PGED2/ASDA2/RP37/RB5
RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKI/RC12
VDD
SCL1/RPI53/RC5
SDA1/RPI52/RC4
SCK1/RPI51/RC3
SDI1/RPI25/RA9
CVREF2O/SDO1/RP20/T1CK/RA4
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/
O Ports” for more information.
3: This pin is not available as an input when OPMODE (CMxCON<10>) = 1.
DS70657E-page 16
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
= Pins are up to 5V tolerant
RPI45/PWM2L/CTPLS/RB13
RPI44/PWM2H/RB12
RP43/PWM3L/RB11
RP42/PWM3H/RB10
RP97/RF1
RPI96/RF0
VDD
VCAP
RP57/RC9
RD6
RD5
RP56/RC8
RP55/RC7
RP54/RC6
TMS/ASDA1/RP41/RB9
62
61
60
59
58
57
56
55
54
53
52
51
50
49
TDO/RA10
63
48
47
46
4
5
6
7
8
9
10
11
12
45
44
43
42
41
40
39
38
37
dsPIC33EP64MC206/506
dsPIC33EP128MC206/506
dsPIC33EP256MC206/506
dsPIC33EP512MC206/506
PIC24EP64MC206
PIC24EP128MC206
PIC24EP256MC206
PIC24EP512MC206
28
29
30
31
32
AN13/C3IN2-(3)/U2CTS/RE13
AN14/RPI94/RE14
AN15/RPI95/RE15
SDA2/RPI24/RA8
FLT32/SCL2/RP36/RB4
27
AN12/C2IN2- /U2RTS/BCLK2/RE12
26
VDD
23
AN8/C3IN1+/U1RTS/BCLK1/FLT3/RC2
(3)
22
AN7/C3IN1-/C4IN1-/RC1
25
21
AN6/OA3OUT/C4IN1+/OCFB/RC0
VSS
20
AVSS
24
19
AVDD
AN11/C1IN2-(3)/U1CTS/FLT4/RC11
18
36
35
34
33
17
13
14
15
16
PGED1/AN5/C1IN1-/RP35/RB3
VDD
AN10/RPI28/RA12
AN9/RPI27/RA11
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
1
2
3
PGEC1/AN4/C1IN1+/RPI34/RB2
TDI/RA7
RPI46/PWM1H/T3CK/RB14
RPI47/PWM1L/T5CK/RB15
RP118/RG6
RPI119/RG7
RP120/RG8
MCLR
RPI121/RG9
VSS
64
64-Pin TQFP
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RC13
RP39/INT0/RB7
RPI58/RC10
PGEC2/ASCL2/RP38/RB6
PGED2/ASDA2/RP37/RB5
RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKI/RC12
VDD
SCL1/RPI53/RC5
SDA1/RPI52/RC4
SCK1/RPI51/RC3
SDI1/RPI25/RA9
CVREF2O/SDO1/RP20/T1CK/RA4
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/
O Ports” for more information.
3: This pin is not available as an input when OPMODE (CMxCON<10>) = 1.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 17
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
64-Pin QFN(4)
TDO/RA10
RPI45/CTPLS/RB13
RPI44/RB12
RP43/RB11
RP42/RB10
RP97/RF1
RPI96/RF0
VDD
VCAP
RP57/RC9
RD6
RD5
RP56/RC8
RP55/RC7
RP54/RC6
TMS/ASDA1/RP41/RB9
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
4
5
6
7
8
9
10
11
12
45
44
43
42
41
40
39
38
37
dsPIC33EP64GP506
dsPIC33EP128GP506
dsPIC33EP256GP506
dsPIC33EP512GP506
PIC24EP64GP206
PIC24EP128GP206
PIC24EP256GP206
PIC24EP512GP206
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AVDD
AVSS
AN6/OA3OUT/C4IN1+/OCFB/RC0
AN7/C3IN1-/C4IN1-/RC1
AN8/C3IN1+/U1RTS/BCLK1/RC2
AN11/C1IN2-(3)/U1CTS/RC11
VSS
VDD
AN12/C2IN2-(3)/U2RTS/BCLK2/RE12
AN13/C3IN2-(3)/U2CTS/RE13
AN14/RPI94/RE14
AN15/RPI95/RE15
SDA2/RPI24/RA8
SCL2/RP36/RB4
36
35
34
33
17
13
14
15
16
PGED1/AN5/C1IN1-/RP35/RB3
VDD
AN10/RPI28/RA12
AN9/RPI27/RA11
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
1
2
3
PGEC1/AN4/C1IN1+/RPI34/RB2
TDI/RA7
RPI46/T3CK/RB14
RPI47/T5CK/RB15
RP118/RG6
RPI119/RG7
RP120/RG8
MCLR
RPI121/RG9
VSS
64
= Pins are up to 5V tolerant
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RC13
RP39/INT0/RB7
RPI58/RC10
PGEC2/ASCL2/RP38/RB6
PGED2/ASDA2/RP37/RB5
RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKI/RC12
VDD
SCL1/RPI53/RC5
SDA1/RPI52/RC4
SCK1/RPI51/RC3
SDI1/RPI25/RA9
CVREF2O/SDO1/RP20/T1CK/RA4
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/
O Ports” for more information.
3: This pin is not available as an input when OPMODE (CMxCON<10>) = 1.
4: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70657E-page 18
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Pin Diagrams (Continued)
64-Pin QFN(4)
TDO/RA10
RPI45/PWM2L/CTPLS/RB13
RPI44/PWM2H/RB12
RP43/PWM3L/RB11
RP42/PWM3H/RB10
RP97/RF1
RPI96/RF0
VDD
VCAP
RP57/RC9
RD6
RD5
RP56/RC8
RP55/RC7
RP54/RC6
TMS/ASDA1/RP41/RB9
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
4
5
6
7
8
9
10
11
12
45
44
43
42
41
40
39
38
37
dsPIC33EP64MC206/506
dsPIC33EP128MC206/506
dsPIC33EP256MC206/506
dsPIC33EP512MC206/506
PIC24EP64MC206
PIC24EP128MC206
PIC24EP256MC206
PIC24EP512MC206
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AVDD
AVSS
AN6/OA3OUT/C4IN1+/OCFB/RC0
AN7/C3IN1-/C4IN1-/RC1
AN8/C3IN1+/U1RTS/BCLK1/FLT3/RC2
AN11/C1IN2-(3)/U1CTS/FLT4/RC11
VSS
VDD
AN12/C2IN2-(3)/U2RTS/BCLK2/RE12
AN13/C3IN2-(3)/U2CTS/RE13
AN14/RPI94/RE14
AN15/RPI95/RE15
SDA2/RPI24/RA8
FLT32/SCL2/RP36/RB4
36
35
34
33
17
13
14
15
16
PGED1/AN5/C1IN1-/RP35/RB3
VDD
AN10/RPI28/RA12
AN9/RPI27/RA11
AN0/OA2OUT/RA0
AN1/C2IN1+/RA1
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
1
2
3
PGEC1/AN4/C1IN1+/RPI34/RB2
TDI/RA7
RPI46/PWM1H/T3CK/RB14
RPI47/PWM1L/T5CK/RB15
RP118/RG6
RPI119/RG7
RP120/RG8
MCLR
RPI121/RG9
VSS
= Pins are up to 5V tolerant
TCK/CVREF1O/ASCL1/RP40/T4CK/RB8
RC13
RP39/INT0/RB7
RPI58/RC10
PGEC2/ASCL2/RP38/RB6
PGED2/ASDA2/RP37/RB5
RD8
VSS
OSC2/CLKO/RC15
OSC1/CLKI/RC12
VDD
SCL1/RPI53/RC5
SDA1/RPI52/RC4
SCK1/RPI51/RC3
SDI1/RPI25/RA9
CVREF2O/SDO1/RP20/T1CK/RA4
Note 1: The RPn/RPIn pins can be used by any remappable peripheral with some limitation. See Section 11.4
“Peripheral Pin Select” for available peripherals and for information on limitations.
2: Every I/O port pin (RAx-RGx) can be used as change notification (CNAx-CNGx). See Section 11.0 “I/O
Ports” for more information.
3: This pin is not available as an input when OPMODE (CMxCON<10>) = 1.
4: The metal pad at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 19
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Table of Contents
1.0 Device Overview ........................................................................................................................................................................ 23
2.0 Guidelines for Getting Started with 16-bit Digital Signal Controllers and Microcontrollers ......................................................... 27
3.0 CPU............................................................................................................................................................................................ 33
4.0 Memory Organization ................................................................................................................................................................. 43
5.0 Flash Program Memory ............................................................................................................................................................ 117
6.0 Resets ..................................................................................................................................................................................... 121
7.0 Interrupt Controller ................................................................................................................................................................... 125
8.0 Direct Memory Access (DMA) .................................................................................................................................................. 137
9.0 Oscillator Configuration ............................................................................................................................................................ 151
10.0 Power-Saving Features............................................................................................................................................................ 161
11.0 I/O Ports ................................................................................................................................................................................... 171
12.0 Timer1 ...................................................................................................................................................................................... 203
13.0 Timer2/3 and Timer4/5 ............................................................................................................................................................ 207
14.0 Input Capture............................................................................................................................................................................ 213
15.0 Output Compare....................................................................................................................................................................... 219
16.0 High-Speed PWM Module (dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X Devices Only) ....................................... 225
17.0 Quadrature Encoder Interface (QEI) Module (dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X Devices Only)........... 249
18.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 265
19.0 Inter-Integrated Circuit™ (I2C™) .............................................................................................................................................. 273
20.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 281
21.0 Enhanced CAN (ECAN™) Module (dsPIC33EPXXXGP/MC50X Devices Only) ..................................................................... 287
22.0 Charge Time Measurement Unit (CTMU) ............................................................................................................................... 313
23.0 10-bit/12-bit Analog-to-Digital Converter (ADC) ....................................................................................................................... 319
24.0 Peripheral Trigger Generator (PTG) Module ............................................................................................................................ 333
25.0 Op amp/Comparator Module .................................................................................................................................................... 351
26.0 Programmable Cyclic Redundancy Check (CRC) Generator .................................................................................................. 369
27.0 Special Features ...................................................................................................................................................................... 375
28.0 Instruction Set Summary .......................................................................................................................................................... 383
29.0 Development Support............................................................................................................................................................... 393
30.0 Electrical Characteristics .......................................................................................................................................................... 397
31.0 DC and AC Device Characteristics Graphs.............................................................................................................................. 463
32.0 Packaging Information.............................................................................................................................................................. 467
Appendix A: Revision History............................................................................................................................................................. 491
Index ................................................................................................................................................................................................. 499
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department
via E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150.
We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS70657E-page 20
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Referenced Sources
This device data sheet is based on the following
individual chapters of the “dsPIC33E/PIC24E Family
Reference Manual”. These documents should be
considered as the general reference for the operation
of a particular module or device feature.
Note 1: To access the documents listed below,
browse to the documentation section of
the dsPIC33EP64MC506 product page
of
the
Microchip
web
site
(www.microchip.com) or select a family
reference manual section from the
following list.
In addition to parameters, features, and
other documentation, the resulting page
provides links to the related family
reference manual sections.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Section 1. “Introduction” (DS70573)
Section 2. “CPU” (DS70359)
Section 3. “Data Memory” (DS70595)
Section 4. “Program Memory” (DS70613)
Section 5. “Flash Programming” (DS70609)
Section 6. “Interrupts” (DS70600)
Section 7. “Oscillator” (DS70580)
Section 8. “Reset” (DS70602)
Section 9. “Watchdog Timer and Power-Saving Modes” (DS70615)
Section 10. “I/O Ports” (DS70598)
Section 11. “Timers” (DS70362)
Section 12. “Input Capture” (DS70352)
Section 13. “Output Compare” (DS70358)
Section 14. “High-Speed PWM” (DS70645)
Section 15. “Quadrature Encoder Interface (QEI)” (DS70601)
Section 16. “Analog-to-Digital Converter (ADC)” (DS70621)
Section 17. “UART” (DS70582)
Section 18. “Serial Peripheral Interface (SPI)” (DS70569)
Section 19. “Inter-Integrated Circuit (I2C™)” (DS70330)
Section 21. “Enhanced Controller Area Network (ECAN™)” (DS70353)
Section 22. “Direct Memory Access (DMA)” (DS70348)
Section 23. “CodeGuard™ Security” (DS70634)
Section 24. “Programming and Diagnostics” (DS70608)
Section 26. “Op amp/Comparator” (DS70357)
Section 27. “Programmable Cyclic Redundancy Check (CRC)” (DS70346)
Section 30. “Device Configuration” (DS70618)
Section 32. “Peripheral Trigger Generator (PTG)” (DS70669)
Section 33. “Charge Time Measurement Unit (CTMU)” (DS70661)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 21
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 22
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
1.0
DEVICE OVERVIEW
This document contains device-specific information for
the dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X Digital Signal
Controller (DSC) and Microcontroller (MCU) devices.
Note 1: This data sheet summarizes the features of the dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive resource. To complement
the information in this data sheet, refer
to the related section of the “dsPIC33E/
PIC24E Family Reference Manual”,
which is available from the Microchip
web site (www.microchip.com)
dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X
devices contain extensive Digital Signal Processor (DSP)
functionality with a high-performance 16-bit MCU
architecture.
Figure 1-1 shows a general block diagram of the core
and peripheral modules. Table 1-1 lists the functions of
the various pins shown in the pinout diagrams.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 1-1:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
BLOCK DIAGRAM
PORTA
CPU
16
Refer to Figure 3-1 for CPU diagram details.
PORTA
PORTC
Power-up
Timer
OSC1/CLKI
Timing
Generation
MCLR
VDD, VSS
AVDD, AVSS
PTG
Op amp/
Comparator
ECAN1(2)
ADC
Oscillator
Start-up
Timer
PORTD
POR/BOR
PORTE
16
Watchdog
Timer
PORTF
Input
Capture
Output
Compare
I2C1,
I2C2
PORTG
Remappable
Pins
QEI1(1)
CTMU
PWM(1)
Timers
CRC
SPI1,
SPI2
UART1,
UART2
PORTS
Peripheral Modules
Note 1:
2:
This feature or peripheral is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
This feature or peripheral is only available on dsPIC33EPXXXGP/MC50X devices.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 23
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 1-1:
PINOUT I/O DESCRIPTIONS
Pin Name(4)
Pin Buffer
PPS
Type Type
Description
AN0-AN15
I
Analog
No
Analog input channels.
CLKI
I
ST/
CMOS
No
CLKO
O
—
No
External clock source input. Always associated with OSC1 pin function.
Oscillator crystal output. Connects to crystal or resonator in Crystal
Oscillator mode. Optionally functions as CLKO in RC and EC modes.
Always associated with OSC2 pin function.
OSC1
I
No
OSC2
I/O
ST/
CMOS
—
REFCLKO
O
—
Yes Reference clock output.
IC1-IC4
I
ST
Yes Capture inputs 1 through 4.
OCFA
OCFB
OC1-OC4
I
I
O
ST
ST
—
Yes Compare Fault A input (for Compare channels).
No Compare Fault B input (for Compare channels).
Yes Compare outputs 1 through 4.
INT0
INT1
INT2
I
I
I
ST
ST
ST
No External interrupt 0.
Yes External interrupt 1.
Yes External interrupt 2.
RA0-RA4, RA7-RA12
I/O
ST
No
PORTA is a bidirectional I/O port.
RB0-RB15
I/O
ST
No
PORTB is a bidirectional I/O port.
RC0-RC13, RC15
I/O
ST
No
PORTC is a bidirectional I/O port.
RD5, RD6, RD8
I/O
ST
No
PORTD is a bidirectional I/O port.
RE12-RE15
I/O
ST
No
PORTE is a bidirectional I/O port.
No
Oscillator crystal input. ST buffer when configured in RC mode; CMOS
otherwise.
Oscillator crystal output. Connects to crystal or resonator in Crystal
Oscillator mode. Optionally functions as CLKO in RC and EC modes.
RF0, RF1
I/O
ST
No
PORTF is a bidirectional I/O port.
RG6-RG9
I/O
ST
No
PORTG is a bidirectional I/O port.
T1CK
T2CK
T3CK
T4CK
T5CK
I
I
I
I
I
ST
ST
ST
ST
ST
No
Yes
No
No
No
Timer1 external clock input.
Timer2 external clock input.
Timer3 external clock input.
Timer4 external clock input.
Timer5 external clock input.
CTPLS
CTED1
CTED2
O
I
I
ST
ST
ST
No
No
No
CTMU pulse output.
CTMU external edge input 1.
CTMU external edge input 2.
U1CTS
U1RTS
U1RX
U1TX
BCLK1
I
O
I
O
O
ST
—
ST
—
ST
No
No
Yes
Yes
No
UART1 clear to send.
UART1 ready to send.
UART1 receive.
UART1 transmit.
UART1 IrDA baud clock output.
Legend: CMOS = CMOS compatible input or output
Analog = Analog input
P = Power
ST = Schmitt Trigger input with CMOS levels
O = Output
I = Input
PPS = Peripheral Pin Select
TTL = TTL input buffer
Note 1: This pin is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
2: This pin is available on dsPIC33EPXXXGP/MC50X devices only.
3: This is the default Fault on Reset for dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices. See
Section 16.0 “High-Speed PWM Module (dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X
Devices Only)” for more information.
4: Not all pins are available in all packages variants. See the “Pin Diagrams” section for pin availability.
DS70657E-page 24
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 1-1:
PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Name(4)
Pin Buffer
PPS
Type Type
Description
U2CTS
U2RTS
U2RX
U2TX
BCLK2
I
O
I
O
O
ST
—
ST
—
ST
No
No
Yes
Yes
No
UART2 clear to send.
UART2 ready to send.
UART2 receive.
UART2 transmit.
UART2 IrDA baud clock output.
SCK1
SDI1
SDO1
SS1
I/O
I
O
I/O
ST
ST
—
ST
No
No
No
No
Synchronous serial clock input/output for SPI1.
SPI1 data in.
SPI1 data out.
SPI1 slave synchronization or frame pulse I/O.
SCK2
SDI2
SDO2
SS2
I/O
I
O
I/O
ST
ST
—
ST
Yes
Yes
Yes
Yes
Synchronous serial clock input/output for SPI2.
SPI2 data in.
SPI2 data out.
SPI2 slave synchronization or frame pulse I/O.
SCL1
SDA1
ASCL1
ASDA1
I/O
I/O
I/O
I/O
ST
ST
ST
ST
No
No
No
No
Synchronous serial clock input/output for I2C1.
Synchronous serial data input/output for I2C1.
Alternate synchronous serial clock input/output for I2C1.
Alternate synchronous serial data input/output for I2C1.
SCL2
SDA2
ASCL2
ASDA2
I/O
I/O
I/O
I/O
ST
ST
ST
ST
No
No
No
No
Synchronous serial clock input/output for I2C2.
Synchronous serial data input/output for I2C2.
Alternate synchronous serial clock input/output for I2C2.
Alternate synchronous serial data input/output for I2C2.
TMS
TCK
TDI
TDO
I
I
I
O
ST
ST
ST
—
No
No
No
No
JTAG Test mode select pin.
JTAG test clock input pin.
JTAG test data input pin.
JTAG test data output pin.
C1RX(2)
C1TX(2)
I
O
ST
—
Yes ECAN1 bus receive pin.
Yes ECAN1 bus transmit pin.
FLT1(1), FLT2(1)
FLT3(1), FLT4(1)
FLT32(1,3)
DTCMP1-DTCMP3(1)
PWM1L-PWM3L(1)
PWM1H-PWM3H(1)
SYNCI1(1)
SYNCO1(1)
I
I
I
I
O
O
I
O
ST
ST
ST
ST
—
—
ST
—
Yes
No
No
Yes
No
No
Yes
Yes
INDX1(1)
HOME1(1)
QEA1(1)
I
I
I
ST
ST
ST
QEB1(1)
I
ST
CNTCMP1(1)
O
—
Yes Quadrature Encoder Index1 Pulse input.
Yes Quadrature Encoder Home1 Pulse input.
Yes Quadrature Encoder Phase A input in QEI1 mode. Auxiliary Timer
External Clock/Gate input in Timer mode.
Yes Quadrature Encoder Phase B input in QEI1 mode. Auxiliary Timer
External Clock/Gate input in Timer mode.
Yes Quadrature Encoder Compare Output 1.
PWM Fault input 1 and 2.
PWM Fault input 3 and 4.
PWM Fault input 32 (Class B Fault).
PWM Dead Time Compensation Input 1 through 3.
PWM Low Output 1 through 3.
PWM High Output 1 through 3.
PWM Synchronization Input 1.
PWM Synchronization Output 1.
Legend: CMOS = CMOS compatible input or output
Analog = Analog input
P = Power
ST = Schmitt Trigger input with CMOS levels
O = Output
I = Input
PPS = Peripheral Pin Select
TTL = TTL input buffer
Note 1: This pin is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
2: This pin is available on dsPIC33EPXXXGP/MC50X devices only.
3: This is the default Fault on Reset for dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices. See
Section 16.0 “High-Speed PWM Module (dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X
Devices Only)” for more information.
4: Not all pins are available in all packages variants. See the “Pin Diagrams” section for pin availability.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 25
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 1-1:
Pin Name(4)
PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Buffer
PPS
Type Type
Description
C1IN1C1IN2C1IN1+
OA1OUT
C1OUT
I
I
I
O
O
Analog
Analog
Analog
Analog
—
No
No
No
No
Yes
Op amp/Comparator 1 Negative Input 1.
Comparator 1 Negative Input 2.
Op amp/Comparator 1 Positive Input 1.
Op amp 1 Output.
Comparator 1 Output.
C2IN1C2IN2C2IN1+
OA2OUT
C2OUT
I
I
I
O
O
Analog
Analog
Analog
Analog
—
No
No
No
No
Yes
Op amp/Comparator 2 Negative Input 1.
Comparator 2 Negative Input 2.
Op amp/Comparator 2 Positive Input 1.
Op amp 2 Output.
Comparator 2 Output.
C3IN1C3IN2C3IN1+
OA3OUT
C3OUT
I
I
I
O
O
Analog
Analog
Analog
Analog
—
No
No
No
No
Yes
Op amp/Comparator 3 Negative Input 1.
Comparator 3 Negative Input 2.
Op amp/Comparator 3 Positive Input 1.
Op amp 3 Output.
Comparator 3 Output.
C4IN1C4IN1+
C4OUT
I
I
O
Analog
Analog
—
No Comparator 4 Negative Input 1.
No Comparator 4 Positive Input 1.
Yes Comparator 4 Output.
CVREF1O
CVREF2O
O
O
Analog
Analog
No
No
Op amp/Comparator Voltage Reference Output.
Op amp/Comparator Voltage Reference divided by 2 Output.
PGED1
PGEC1
PGED2
PGEC2
PGED3
PGEC3
I/O
I
I/O
I
I/O
I
ST
ST
ST
ST
ST
ST
No
No
No
No
No
No
Data I/O pin for programming/debugging communication channel 1.
Clock input pin for programming/debugging communication channel 1.
Data I/O pin for programming/debugging communication channel 2.
Clock input pin for programming/debugging communication channel 2.
Data I/O pin for programming/debugging communication channel 3.
Clock input pin for programming/debugging communication channel 3.
MCLR
I/P
ST
No
Master Clear (Reset) input. This pin is an active-low Reset to the
device.
AVDD
P
P
No
Positive supply for analog modules. This pin must be connected at all
times.
AVSS
P
P
No
Ground reference for analog modules. This pin must be connected at all
times.
VDD
P
—
No
Positive supply for peripheral logic and I/O pins.
VCAP
P
—
No
CPU logic filter capacitor connection.
VSS
P
—
No
Ground reference for logic and I/O pins.
VREF+
I
Analog
No
Analog voltage reference (high) input.
VREF-
I
Analog
No
Analog voltage reference (low) input.
Legend: CMOS = CMOS compatible input or output
Analog = Analog input
P = Power
ST = Schmitt Trigger input with CMOS levels
O = Output
I = Input
PPS = Peripheral Pin Select
TTL = TTL input buffer
Note 1: This pin is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
2: This pin is available on dsPIC33EPXXXGP/MC50X devices only.
3: This is the default Fault on Reset for dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices. See
Section 16.0 “High-Speed PWM Module (dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X
Devices Only)” for more information.
4: Not all pins are available in all packages variants. See the “Pin Diagrams” section for pin availability.
DS70657E-page 26
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
2.0
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
DIGITAL SIGNAL
CONTROLLERS AND
MICROCONTROLLERS
2.2
The use of decoupling capacitors on every pair of
power supply pins, such as VDD, VSS, AVDD and
AVSS is required.
Consider the following criteria when using decoupling
capacitors:
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet,
refer to the related section of the
“dsPIC33E/PIC24E Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com)
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
2.1
Decoupling Capacitors
Basic Connection Requirements
Getting started with the dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families requires attention to a
minimal set of device pin connections before proceeding
with development. The following is a list of pin names,
which must always be connected:
• All VDD and VSS pins
(see Section 2.2 “Decoupling Capacitors”)
• All AVDD and AVSS pins (regardless if ADC module
is not used)
(see Section 2.2 “Decoupling Capacitors”)
• VCAP
(see Section 2.3 “CPU Logic Filter Capacitor
Connection (VCAP)”)
• MCLR pin
(see Section 2.4 “Master Clear (MCLR) Pin”)
• PGECx/PGEDx pins used for In-Circuit Serial
Programming™ (ICSP™) and debugging purposes
(see Section 2.5 “ICSP Pins”)
• OSC1 and OSC2 pins when external oscillator
source is used
(see Section 2.6 “External Oscillator Pins”)
• Value and type of capacitor: Recommendation
of 0.1 µF (100 nF), 10-20V. This capacitor should
be a low-ESR and have resonance frequency in
the range of 20 MHz and higher. It is
recommended to use ceramic capacitors.
• Placement on the printed circuit board: The
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is within
one-quarter inch (6 mm) in length.
• Handling high frequency noise: If the board is
experiencing high frequency noise, above tens of
MHz, add a second ceramic-type capacitor in
parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 µF to 0.001 µF. Place this
second capacitor next to the primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible.
For example, 0.1 µF in parallel with 0.001 µF.
• Maximizing performance: On the board layout
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum, thereby reducing PCB track
inductance.
Additionally, the following pins may be required:
• VREF+/VREF- pins are used when external voltage
reference for ADC module is implemented
Note:
The AVDD and AVSS pins must be
connected independent of the ADC
voltage reference source.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 27
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 2-1:
RECOMMENDED
MINIMUM CONNECTION
0.1 µF
Ceramic
10 µF
Tantalum
R
R1
VSS
VDD
2.4
VCAP
VDD
dsPIC33E/PIC24E
VSS
VDD
VSS
VDD
AVSS
VDD
AVDD
VSS
0.1 µF
Ceramic
0.1 µF
Ceramic
L1(1)
Note
1:
As an option, instead of a hard-wired connection, an
inductor (L1) can be substituted between VDD and
AVDD to improve ADC noise rejection. The inductor
impedance should be less than 1Ω and the inductor
capacity greater than 10 mA.
Where:
CNV
------------f = F
2
1
f = ----------------------( 2π LC )
two
specific
device
For example, as shown in Figure 2-2, it is
recommended that the capacitor C, be isolated from
the MCLR pin during programming and debugging
operations.
Place the components as shown in Figure 2-2 within
one-quarter inch (6 mm) from the MCLR pin.
FIGURE 2-2:
(i.e., ADC conversion rate/2)
EXAMPLE OF MCLR PIN
CONNECTIONS
VDD
R(1)
TANK CAPACITORS
On boards with power traces running longer than six
inches in length, it is suggested to use a tank capacitor
for integrated circuits including DSCs to supply a local
power source. The value of the tank capacitor should
be determined based on the trace resistance that connects the power supply source to the device, and the
maximum current drawn by the device in the application. In other words, select the tank capacitor so that it
meets the acceptable voltage sag at the device. Typical
values range from 4.7 µF to 47 µF.
2.3
provides
During device programming and debugging, the
resistance and capacitance that can be added to the
pin must be considered. Device programmers and
debuggers drive the MCLR pin. Consequently,
specific voltage levels (VIH and VIL) and fast signal
transitions must not be adversely affected. Therefore,
specific values of R and C will need to be adjusted
based on the application and PCB requirements.
2
1
L = ⎛⎝ ---------------------⎞⎠
( 2πf C )
2.2.1
pin
• Device Reset
• Device Programming and Debugging.
C
0.1 µF
Ceramic
Master Clear (MCLR) Pin
The MCLR
functions:
MCLR
0.1 µF
Ceramic
The placement of this capacitor should be close to the
VCAP pin. It is recommended that the trace length not
exceeds one-quarter inch (6 mm). See Section 27.3
“On-Chip Voltage Regulator” for details.
JP
R1(2)
MCLR
dsPIC33EP/PIC24EP
C
Note 1:
R ≤ 10 kΩ is recommended. A suggested
starting value is 10 kΩ. Ensure that the MCLR
pin VIH and VIL specifications are met.
2:
R1 ≤ 470Ω will limit any current flowing into
MCLR from the external capacitor C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
VIH and VIL specifications are met.
CPU Logic Filter Capacitor
Connection (VCAP)
A low-ESR (< 1 Ohms) capacitor is required on the
VCAP pin, which is used to stabilize the voltage
regulator output voltage. The VCAP pin must not be
connected to VDD, and must have a capacitor greater
than 4.7 µF (10 µF is recommended), 16V connected
to ground. The type can be ceramic or tantalum. See
Section 30.0 “Electrical Characteristics” for
additional information.
DS70657E-page 28
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
2.5
ICSP Pins
2.6
The PGECx and PGEDx pins are used for ICSP and
debugging purposes. It is recommended to keep the
trace length between the ICSP connector and the ICSP
pins on the device as short as possible. If the ICSP connector is expected to experience an ESD event, a
series resistor is recommended, with the value in the
range of a few tens of Ohms, not to exceed 100 Ohms.
Pull-up resistors, series diodes and capacitors on the
PGECx and PGEDx pins are not recommended as they
will interfere with the programmer/debugger communications to the device. If such discrete components are
an application requirement, they should be removed
from the circuit during programming and debugging.
Alternatively, refer to the AC/DC characteristics and
timing requirements information in the respective
device Flash programming specification for information
on capacitive loading limits and pin input voltage high
(VIH) and input low (VIL) requirements.
Ensure that the “Communication Channel Select” (i.e.,
PGECx/PGEDx pins) programmed into the device
matches the physical connections for the ICSP to
MPLAB® PICkit™ 3, MPLAB ICD 3, or MPLAB REAL
ICE™.
Many DSCs have options for at least two oscillators: a
high-frequency primary oscillator and a low-frequency
secondary oscillator. For details, see Section 9.0
“Oscillator Configuration” for details.
The oscillator circuit should be placed on the same
side of the board as the device. Also, place the
oscillator circuit close to the respective oscillator pins,
not exceeding one-half inch (12 mm) distance
between them. The load capacitors should be placed
next to the oscillator itself, on the same side of the
board. Use a grounded copper pour around the
oscillator circuit to isolate them from surrounding
circuits. The grounded copper pour should be routed
directly to the MCU ground. Do not run any signal
traces or power traces inside the ground pour. Also, if
using a two-sided board, avoid any traces on the
other side of the board where the crystal is placed. A
suggested layout is shown in Figure 2-3.
FIGURE 2-3:
For more information on ICD 2, ICD 3 and REAL ICE
connection requirements, refer to the following
documents that are available on the Microchip web
site.
• “Using MPLAB® ICD 3” (poster) DS51765
• “MPLAB® ICD 3 Design Advisory” DS51764
• “MPLAB® REAL ICE™ In-Circuit Emulator User’s
Guide” DS51616
• “Using MPLAB® REAL ICE™ In-Circuit Emulator”
(poster) DS51749
© 2011-2012 Microchip Technology Inc.
External Oscillator Pins
Preliminary
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
Main Oscillator
Guard Ring
Guard Trace
Oscillator Pins
DS70657E-page 29
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
2.7
Oscillator Value Conditions on
Device Start-up
2.9
If the PLL of the target device is enabled and
configured for the device start-up oscillator, the
maximum oscillator source frequency must be limited
to 3 MHz < FIN < 5.5 MHz to comply with device PLL
start-up conditions. This means that if the external
oscillator frequency is outside this range, the
application must start-up in the FRC mode first. The
default PLL settings after a POR with an oscillator
frequency outside this range will violate the device
operating speed.
Once the device powers up, the application firmware
can initialize the PLL SFRs, CLKDIV and PLLDBF to a
suitable value, and then perform a clock switch to the
Oscillator + PLL clock source. Note that clock switching
must be enabled in the device Configuration Word.
•
•
•
•
•
•
•
•
•
•
•
•
•
Application Examples
Induction heating
Uninterruptable Power Supplies (UPS)
DC/AC inverters
Compressor motor control
Washing machine 3-phase motor control
BLDC motor control
Automotive HVAC, cooling fans, fuel pumps
Stepper motor control
Audio and fluid sensor monitoring
Camera lens focus and stability control
Speech (playback, hands-free kits, answering
machines, VoIP)
Consumer audio
Industrial and building control (security systems
and access control)
Barcode reading
Networking: LAN switches, gateways
Data storage device management
Smart cards and smart card readers
Unused I/O pins should be configured as outputs and
driven to a logic-low state.
•
•
•
•
Alternatively, connect a 1k to 10k resistor between VSS
and unused pins and drive the output to logic low.
Examples of typical application connections are shown
in Figure 2-4 through Figure 2-8.
2.8
Unused I/Os
FIGURE 2-4:
BOOST CONVERTER IMPLEMENTATION
IPFC
VINPUT
VOUTPUT
k1
k3
ADC Channel
k2
FET
Driver
Op amp/
Comparator
PWM
Output
ADC Channel
dsPIC33EP
DS70657E-page 30
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 2-5:
SINGLE-PHASE SYNCHRONOUS BUCK CONVERTER
12V Input
5V Output
k7
ADC
Channel
FET
Driver
k1
k2
PWM
PWM
I5V
Op amp/
Comparator
ADC
Channel
dsPIC33EP
FIGURE 2-6:
MULTI-PHASE SYNCHRONOUS BUCK CONVERTER
3.3V Output
FET
Driver
dsPIC33EP
PWM
ADC
Channel
FET
Driver
PWM
k7
PWM
PWM
12V Input
k6
PWM
PWM
FET
Driver
Op amp/Comparator
k3
Op amp/Comparator
k4
Op amp/Comparator
k5
ADC Channel
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 31
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 2-7:
INTERLEAVED PFC
VOUT+
|VAC|
k4
VAC
k3
k1
k2
VOUTFET
Driver
Op amp/Comparator
ADC Channel
FIGURE 2-8:
PWM
FET
Driver
Op amp/
Op amp/ PWM
Comparator
Comparator
ADC
Channel
dsPIC33EP
BEMF VOLTAGE MEASURED USING THE ADC MODULE
dsPIC33EP/PIC24EP
BLDC
PWM3H
PWM3L
PWM2H
PWM2L
PWM1H
PWM1L
FLTx
3-Phase
Inverter
Fault
R49
R41
R34 R36
R44
AN2
R52
Demand
AN3
AN4
AN5
DS70657E-page 32
Phase Terminal Voltage Feedback
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
3.0
CPU
3.3
Data Space Addressing
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 2. “CPU”
(DS70359) in the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
The base data space can be addressed as 4K words or
8 Kbytes and is split into two blocks, referred to as X
and Y data memory. Each memory block has its own
independent Address Generation Unit (AGU). The
MCU class of instructions operate solely through the X
memory AGU, which accesses the entire memory map
as one linear data space. On dsPIC33EPXXXMC20X/
50X and dsPIC33EPXXXGP50X devices, certain DSP
instructions operate through the X and Y AGUs to support dual operand reads, which splits the data address
space into two parts. The X and Y data space boundary
is device specific.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The upper 4 Kbytes of the data space memory map can
optionally be mapped into program space at any 16K
program word boundary. The program-to-data-space
mapping feature, known as Program Space Visibility
(PSV), lets any instruction access program space as if
it were data space. Moreover, the Base Data Space
address is used in conjunction with a read or write page
register (DSRPAG or DSWPAG) to form an Extended
Data Space (EDS) address. The EDS can be
addressed as 8 Mwords or 16 Mbytes. Refer to
Section 3. “Data Memory” (DS70595) and Section 4.
“Program Memory” (DS70613) in the “dsPIC33E/
PIC24E Family Reference Manual” for more details on
EDS, PSV and table accesses.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X CPU have a 16-bit
(data) modified Harvard architecture with an enhanced
instruction set, including significant support for digital
signal processing. The CPU has a 24-bit instruction
word, with a variable length opcode field. The Program
Counter (PC) is 23 bits wide and addresses up to
4M x 24 bits of user program memory space.
An instruction prefetch mechanism helps maintain
throughput and provides predictable execution. Most
instructions execute in a single-cycle effective execution rate, with the exception of instructions that change
the program flow, the double-word move (MOV.D)
instruction, PSV accesses, and the table instructions.
Overhead free program loop constructs are supported
using the DO and REPEAT instructions, both of which
are interruptible at any point.
3.1
Registers
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices have sixteen 16-bit Working registers in the programmer’s
model. Each of the Working registers can act as a data,
address or address offset register. The 16th Working
register (W15) operates as a software Stack Pointer for
interrupts and calls.
3.2
Instruction Set
The instruction set for dsPIC33EPXXXGP50X and
dsPIC33EPXXXMC20X/50X devices has two classes of
instructions: the MCU class of instructions and the DSP
class of instructions. The instruction set for
PIC24EPXXXGP/MC20X devices has the MCU class of
instructions only and does not support DSP instructions.
These two instruction classes are seamlessly integrated
into the architecture and execute from a single execution
unit. The instruction set includes many addressing modes
and was designed for optimum C compiler efficiency.
© 2011-2012 Microchip Technology Inc.
On
dsPIC33EPXXXMC20X/50X
and
dsPIC33EPXXXGP50X
devices,
overhead-free
circular buffers (Modulo Addressing) are supported in
both X and Y address spaces. The Modulo Addressing
removes the software boundary-checking overhead for
DSP algorithms. The X AGU circular addressing can be
used with any of the MCU class of instructions. The X
AGU also supports Bit-Reverse Addressing to greatly
simplify input or output data reordering for radix-2 FFT
algorithms. PIC24EPXXXGP/MC20X devices do not
support Modulo and Bit-Reverse Addressing.
3.4
Addressing Modes
The CPU supports these addressing modes:
•
•
•
•
•
•
Inherent (no operand)
Relative
Literal
Memory Direct
Register Direct
Register Indirect
Each instruction is associated with a predefined
Addressing mode group, depending upon its functional
requirements. As many as six Addressing modes are
supported for each instruction.
Preliminary
DS70657E-page 33
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 3-1:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
CPU BLOCK DIAGRAM
X Address Bus
(1)
Y Data Bus
X Data Bus
16
16
Interrupt
Controller
PSV and Table
Data Access
24 Control Block
8
16
16
Data Latch
Data Latch
Y Data
RAM(1)
X Data
RAM
16
Address
Latch
24
Y Address Bus
24
PCU PCH PCL
Program Counter
Loop
Stack
Control
Control
Logic
Logic
Address Latch
16
X RAGU
X WAGU
16
16
Address
Latch
24
16
Y AGU(1)
Program Memory
Data Latch
24
16
Literal Data
IR
ROM Latch
24
EA MUX
16
16
16
16 x 16
W Register Array
16
16
16
Divide
Support
DSP
Engine(1)
16-bit ALU
Control Signals
to Various Blocks
Instruction
Decode and
Control
16
Power, Reset,
and Oscillator
Modules
16
Ports
Peripheral
Modules
Note 1: This feature is not available on PIC24EPXXXGP/MC20X devices.
DS70657E-page 34
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
3.5
Programmer’s Model
The
programmer’s
model
for
the
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X is shown in Figure 3-2.
All registers in the programmer’s model are memory
mapped and can be manipulated directly by
instructions. Table 3-1 lists a description of each
register.
In addition to the registers contained in the
programmer’s model, the dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X devices contain control registers for Modulo
Addressing
(dsPIC33EPXXXMC20X/50X
and
dsPIC33EPXXXGP50X devices only), Bit-Reversed
Addressing
(dsPIC33EPXXXMC20X/50X
and
dsPIC33EPXXXGP50X devices only) and interrupts.
These registers are described in subsequent sections
of this document.
All registers associated with the programmer’s model
are memory mapped, as shown in Table 4-1.
TABLE 3-1:
PROGRAMMER’S MODEL REGISTER DESCRIPTIONS
Register(s) Name
Description
W0 through W15
Working register array
ACCA, ACCB
40-bit DSP Accumulators
PC
23-bit Program Counter
SR
ALU and DSP Engine Status register
SPLIM
Stack Pointer Limit Value register
TBLPAG
Table Memory Page Address register
DSRPAG
Extended Data Space (EDS) Read Page register
DSWPAG
Extended Data Space (EDS) Write Page register
RCOUNT
REPEAT Loop Count register
DCOUNT(1)
DO Loop Count register
DOSTARTH(1,2),
DOENDH(1),
DOSTARTL(1,2)
DOENDL(1)
CORCON
Note 1:
2:
DO Loop Start Address register (High and Low)
DO Loop End Address register (High and Low)
Contains DSP Engine, DO Loop control and trap status bits
This register is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
The DOSTARTH and DOSTARTL registers are read-only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 35
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 3-2:
PROGRAMMER’S MODEL
D15
D0
W0 (WREG)
W1
W2
W3
W4
DSP Operand
Registers
W5
W6
W7
Working/Address
Registers
W8
W9
DSP Address
Registers
W10
W11
W12
W13
Frame Pointer/W14
Stack Pointer/W15* 0
PUSH.s and POP.s shadows
Nested DO Stack
AD39
DSP
Accumulators(1)
Stack Pointer Limit
0
SPLIM*
AD15
AD31
AD0
ACCA
ACCB
PC23
0
PC0
0
Program Counter
0
7
TBLPAG
Data Table Page Address
9
0
DSRPAG
X Data Space Read Page Address
8
0
DSWPAG
X Data Space Write Page Address
15
0
RCOUNT
Repeat Loop Counter
15
0
DCOUNT
DO Loop Counter and Stack(1)
23
0
DOSTART
0
0
DO Loop Start Address and Stack(1)
23
0
DOEND
0
0
DO Loop End Address and Stack(1)
15
0
CPU Core Control Register
CORCON
SRL
OA(1) OB(1) SA(1) SB(1) OAB(1) SAB(1) DA(1) DC IPL2 IPL1 IPL0 RA
Note 1:
N
OV
Z
C
Status Register
This feature or bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
DS70657E-page 36
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
3.6
CPU Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
3.6.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 2. “CPU” (DS70359)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 37
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
3.7
CPU Control Registers
REGISTER 3-1:
SR: CPU STATUS REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/C-0
R/C-0
R -0
(1)
(1)
(1,4)
(1,4)
(1)
(1)
(1)
OA
OB
SA
SB
OAB
SAB
R/W-0
DA
DC
bit 15
bit 8
R/W-0(2,3)
R/W-0(2,3)
R/W-0(2,3)
IPL<2:0>
R-0
R/W-0
R/W-0
R/W-0
R/W-0
RA
N
OV
Z
C
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
C = Clearable bit
-n = Value at POR
‘1’= Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
OA: Accumulator A Overflow Status bit(1)
1 = Accumulator A has overflowed
0 = Accumulator A has not overflowed
bit 14
OB: Accumulator B Overflow Status bit(1)
1 = Accumulator B has overflowed
0 = Accumulator B has not overflowed
bit 13
SA: Accumulator A Saturation ‘Sticky’ Status bit(1,4)
1 = Accumulator A is saturated or has been saturated at some time
0 = Accumulator A is not saturated
bit 12
SB: Accumulator B Saturation ‘Sticky’ Status bit(1,4)
1 = Accumulator B is saturated or has been saturated at some time
0 = Accumulator B is not saturated
bit 11
OAB: OA || OB Combined Accumulator Overflow Status bit(1)
1 = Accumulators A or B have overflowed
0 = Neither Accumulators A or B have overflowed
bit 10
SAB: SA || SB Combined Accumulator ‘Sticky’ Status bit(1)
1 = Accumulators A or B are saturated or have been saturated at some time
0 = Neither Accumulator A or B are saturated
bit 9
DA: DO Loop Active bit(1)
1 = DO loop in progress
0 = DO loop not in progress
bit 8
DC: MCU ALU Half Carry/Borrow bit
1 = A carry-out from the 4th low order bit (for byte-sized data) or 8th low order bit (for word-sized data)
of the result occurred
0 = No carry-out from the 4th low order bit (for byte-sized data) or 8th low order bit (for word-sized
data) of the result occurred
Note 1:
2:
3:
4:
This bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the IPL, if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
The IPL<2:0> Status bits are read only when the NSTDIS bit (INTCON1<15>) = 1.
A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by
clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not
be modified using bit operations.
DS70657E-page 38
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 3-1:
SR: CPU STATUS REGISTER (CONTINUED)
bit 7-5
IPL<2:0>: CPU Interrupt Priority Level Status bits(1,2)
111 = CPU Interrupt Priority Level is 7 (15). User interrupts disabled
110 = CPU Interrupt Priority Level is 6 (14)
101 = CPU Interrupt Priority Level is 5 (13)
100 = CPU Interrupt Priority Level is 4 (12)
011 = CPU Interrupt Priority Level is 3 (11)
010 = CPU Interrupt Priority Level is 2 (10)
001 = CPU Interrupt Priority Level is 1 (9)
000 = CPU Interrupt Priority Level is 0 (8)
bit 4
RA: REPEAT Loop Active bit
1 = REPEAT loop in progress
0 = REPEAT loop not in progress
bit 3
N: MCU ALU Negative bit
1 = Result was negative
0 = Result was non-negative (zero or positive)
bit 2
OV: MCU ALU Overflow bit
This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the magnitude that
causes the sign bit to change state.
1 = Overflow occurred for signed arithmetic (in this arithmetic operation)
0 = No overflow occurred
bit 1
Z: MCU ALU Zero bit
1 = An operation that affects the Z bit has set it at some time in the past
0 = The most recent operation that affects the Z bit has cleared it (i.e., a non-zero result)
bit 0
C: MCU ALU Carry/Borrow bit
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note 1:
2:
3:
4:
This bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the IPL, if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
The IPL<2:0> Status bits are read only when the NSTDIS bit (INTCON1<15>) = 1.
A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by
clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not
be modified using bit operations.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 39
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 3-2:
CORCON: CORE CONTROL REGISTER
R/W-0
U-0
VAR
—
R/W-0
R/W-0
US<1:0>(1)
R/W-0
R-0
EDT(1,2)
R-0
R-0
DL<2:0>(1)
bit 15
bit 8
R/W-0
R/W-0
R/W-1
R/W-0
R/C-0
R-0
R/W-0
R/W-0
SATA(1)
SATB(1)
SATDW(1)
ACCSAT(1)
IPL3(3)
SFA
RND(1)
IF(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
VAR: Variable Exception Processing Latency Control bit
1 = Variable exception processing enabled
0 = Fixed exception processing enabled
bit 14
Unimplemented: Read as ‘0’
bit 13-12
US<1:0>: DSP Multiply Unsigned/Signed Control bits(1)
11 = Reserved
10 = DSP engine multiplies are mixed-sign
01 = DSP engine multiplies are unsigned
00 = DSP engine multiplies are signed
bit 11
EDT: Early DO Loop Termination Control bit(1,2)
1 = Terminate executing DO loop at end of current loop iteration
0 = No effect
bit 10-8
DL<2:0>: DO Loop Nesting Level Status bits(1)
111 = 7 DO loops active
•
•
•
001 = 1 DO loop active
000 = 0 DO loops active
bit 7
SATA: ACCA Saturation Enable bit(1)
1 = Accumulator A saturation enabled
0 = Accumulator A saturation disabled
bit 6
SATB: ACCB Saturation Enable bit(1)
1 = Accumulator B saturation enabled
0 = Accumulator B saturation disabled
bit 5
SATDW: Data Space Write from DSP Engine Saturation Enable bit(1)
1 = Data space write saturation enabled
0 = Data space write saturation disabled
bit 4
ACCSAT: Accumulator Saturation Mode Select bit(1)
1 = 9.31 saturation (super saturation)
0 = 1.31 saturation (normal saturation)
bit 3
IPL3: CPU Interrupt Priority Level Status bit 3(3)
1 = CPU interrupt priority level is greater than 7
0 = CPU interrupt priority level is 7 or less
Note 1:
2:
3:
This bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
This bit is always read as ‘0’.
The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU interrupt priority level.
DS70657E-page 40
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 3-2:
CORCON: CORE CONTROL REGISTER (CONTINUED)
bit 2
SFA: Stack Frame Active Status bit
1 = Stack frame is active. W14 and W15 address 0x0000 to 0xFFFF, regardless of DSRPAG and DSWPAG values
0 = Stack frame is not active. W14 and W15 address of EDS or Base Data Space
bit 1
RND: Rounding Mode Select bit(1)
1 = Biased (conventional) rounding enabled
0 = Unbiased (convergent) rounding enabled
bit 0
IF: Integer or Fractional Multiplier Mode Select bit(1)
1 = Integer mode enabled for DSP multiply
0 = Fractional mode enabled for DSP multiply
Note 1:
2:
3:
This bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
This bit is always read as ‘0’.
The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU interrupt priority level.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 41
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
3.8
Arithmetic Logic Unit (ALU)
3.9
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X ALU is 16 bits wide
and is capable of addition, subtraction, bit shifts and
logic operations. Unless otherwise mentioned,
arithmetic operations are two’s complement in nature.
Depending on the operation, the ALU can affect the
values of the Carry (C), Zero (Z), Negative (N),
Overflow (OV) and Digit Carry (DC) Status bits in the
SR register. The C and DC Status bits operate as
Borrow and Digit Borrow bits, respectively, for
subtraction operations.
The ALU can perform 8-bit or 16-bit operations,
depending on the mode of the instruction that is used.
Data for the ALU operation can come from the W
register array or data memory, depending on the
addressing mode of the instruction. Likewise, output
data from the ALU can be written to the W register array
or a data memory location.
Refer to the “16-bit MCU and DSC Programmer’s
Reference Manual” (DS70157) for information on the
SR bits affected by each instruction.
The core CPU incorporates hardware support for both
multiplication and division. This includes a dedicated
hardware multiplier and support hardware for 16-bit
divisor division.
3.8.1
16-bit x 16-bit signed
16-bit x 16-bit unsigned
16-bit signed x 5-bit (literal) unsigned
16-bit signed x 16-bit unsigned
16-bit unsigned x 5-bit (literal) unsigned
16-bit unsigned x 16-bit signed
8-bit unsigned x 8-bit unsigned
3.8.2
DIVIDER
The divide block supports 32-bit/16-bit and 16-bit/16-bit
signed and unsigned integer divide operations with the
following data sizes:
•
•
•
•
The DSP engine consists of a high-speed 17-bit x
17-bit multiplier, a 40-bit barrel shifter and a 40-bit
adder/subtracter (with two target accumulators, round
and saturation logic).
The DSP engine can also perform inherent accumulator-to-accumulator operations that require no additional
data. These instructions are ADD, SUB and NEG.
The DSP engine has options selected through bits in
the CPU Core Control register (CORCON), as listed
below:
•
•
•
•
•
•
Fractional or integer DSP multiply (IF)
Signed, unsigned, or mixed-sign DSP multiply (US)
Conventional or convergent rounding (RND)
Automatic saturation on/off for ACCA (SATA)
Automatic saturation on/off for ACCB (SATB)
Automatic saturation on/off for writes to data
memory (SATDW)
• Accumulator Saturation mode selection
(ACCSAT)
TABLE 3-2:
MULTIPLIER
Using the high-speed 17-bit x 17-bit multiplier, the ALU
supports unsigned, signed, or mixed-sign operation in
several MCU multiplication modes:
•
•
•
•
•
•
•
DSP Engine
(dsPIC33EPXXXMC20X/50X and
dsPIC33EPXXXGP50X Devices
Only)
Instruction
CLR
ED
EDAC
MAC
MAC
MOVSAC
MPY
MPY
MPY.N
MSC
DSP INSTRUCTIONS
SUMMARY
Algebraic
Operation
A=0
2
A = (x – y)
A = A + (x – y)2
A = A + (x • y)
A = A + x2
No change in A
A=x•y
A = x2
A=–x•y
A=A–x•y
ACC Write
Back
Yes
No
No
Yes
No
Yes
No
No
No
Yes
32-bit signed/16-bit signed divide
32-bit unsigned/16-bit unsigned divide
16-bit signed/16-bit signed divide
16-bit unsigned/16-bit unsigned divide
The quotient for all divide instructions ends up in W0
and the remainder in W1. 16-bit signed and unsigned
DIV instructions can specify any W register for both
the 16-bit divisor (Wn) and any W register (aligned)
pair (W(m + 1):Wm) for the 32-bit dividend. The divide
algorithm takes one cycle per bit of divisor, so both
32-bit/16-bit and 16-bit/16-bit instructions take the
same number of cycles to execute.
DS70657E-page 42
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.0
MEMORY ORGANIZATION
Note:
4.1
The program address memory space of the
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices is 4M
instructions. The space is addressable by a 24-bit
value derived either from the 23-bit PC during program
execution, or from table operation or data space
remapping as described in Section 4.8 “Interfacing
Program and Data Memory Spaces”.
This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement
the information in this data sheet, refer to
Section
4.
“Program
Memory”
(DS70613) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is available from the Microchip web site
(www.microchip.com).
User application access to the program memory space
is restricted to the lower half of the address range
(0x000000 to 0x7FFFFF). The exception is the use of
TBLRD operations, which use TBLPAG<7> to read
Device ID sections of the configuration memory space.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X architecture
features separate program and data memory spaces
and buses. This architecture also allows the direct
access of program memory from the data space during
code execution.
FIGURE 4-1:
Program Address Space
The program memory maps, which are presented by
device family and memory size, are shown in
Figure 4-1 through Figure 4-5.
PROGRAM MEMORY MAP FOR dsPIC33EP32GP50X, dsPIC33EP32MC20X/50X,
AND PIC24EP32GP/MC20X DEVICES(1)
GOTO Instruction
0x000000
Reset Address
0x000002
0x000004
0x0001FE
0x000200
User Memory Space
Interrupt Vector Table
User Program
Flash Memory
(11K instructions)
Flash Configuration
Bytes
0x0057EA
0x0057EC
0x0057FE
0x005800
Unimplemented
(Read ‘0’s)
0x7FFFFE
0x800000
Reserved
0x800FF6
0x800FF8
Configuration Memory Space
USERID
Reserved
Write
Latches
0x800FFE
0x801000
0xF9FFFE
0xFA0000
0xFA0002
0xFA0004
Reserved
DEVID
Reserved
0xFEFFFE
0xFF0000
0xFF0002
0xFF0004
0xFFFFFE
Note
1:
Memory areas are not shown to scale.
2:
On reset, these bits are automatically copied into the device Configuration Shadow registers.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 43
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-2:
PROGRAM MEMORY MAP FOR dsPIC33EP64GP50X, dsPIC33EP64MC20X/50X,
AND PIC24EP64GP/MC20X DEVICES(1)
GOTO Instruction
0x000000
Reset Address
0x000002
0x000004
0x0001FE
0x000200
User Memory Space
Interrupt Vector Table
User Program
Flash Memory
(22K instructions)
Flash Configuration
Bytes
0x00AFEA
0x00AFEC
0x00AFFE
0x00B000
Unimplemented
(Read ‘0’s)
0x7FFFFE
0x800000
Reserved
0x800FF6
0x800FF8
Configuration Memory Space
USERID
Reserved
Write
Latches
0x800FFE
0x801000
0xF9FFFE
0xFA0000
0xFA0002
0xFA0004
Reserved
DEVID
Reserved
0xFEFFFE
0xFF0000
0xFF0002
0xFF0004
0xFFFFFE
Note
1:
Memory areas are not shown to scale.
2:
On reset, these bits are automatically copied into the device Configuration Shadow registers.
DS70657E-page 44
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-3:
PROGRAM MEMORY MAP FOR dsPIC33EP128GP50X, dsPIC33EP128MC20X/50X,
AND PIC24EP128GP/MC20X DEVICES(1)
GOTO Instruction
0x000000
Reset Address
0x000002
0x000004
0x0001FE
0x000200
User Memory Space
Interrupt Vector Table
User Program
Flash Memory
(44K instructions)
Flash Configuration
Bytes
0x0157EA
0x0157EC
0x0157FE
0x015800
Unimplemented
(Read ‘0’s)
0x7FFFFE
0x800000
Reserved
0x800FF6
0x800FF8
Configuration Memory Space
USERID
Reserved
Write
Latches
0x800FFE
0x801000
0xF9FFFE
0xFA0000
0xFA0002
0xFA0004
Reserved
DEVID
Reserved
0xFEFFFE
0xFF0000
0xFF0002
0xFF0004
0xFFFFFE
Note
1:
Memory areas are not shown to scale.
2:
On reset, these bits are automatically copied into the device Configuration Shadow registers.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 45
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-4:
PROGRAM MEMORY MAP FOR dsPIC33EP256GP50X, dsPIC33EP256MC20X/50X,
AND PIC24EP256GP/MC20X DEVICES(1)
GOTO Instruction
0x000000
Reset Address
0x000002
0x000004
0x0001FE
0x000200
User Memory Space
Interrupt Vector Table
User Program
Flash Memory
(88K instructions)
Flash Configuration
Bytes
0x02AFEA
0x02AFEC
0x02AFFE
0x02B000
Unimplemented
(Read ‘0’s)
0x7FFFFE
0x800000
Reserved
0x800FF6
0x800FF8
Configuration Memory Space
USERID
Reserved
Write
Latches
0x800FFE
0x801000
0xF9FFFE
0xFA0000
0xFA0002
0xFA0004
Reserved
DEVID
Reserved
0xFEFFFE
0xFF0000
0xFF0002
0xFF0004
0xFFFFFE
Note
1:
Memory areas are not shown to scale.
2:
On reset, these bits are automatically copied into the device Configuration Shadow registers.
DS70657E-page 46
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-5:
PROGRAM MEMORY MAP FOR dsPIC33EP512GP50X, dsPIC33EP512MC20X/50X,
AND PIC24EP512GP/MC20X DEVICES(1)
GOTO Instruction
0x000000
Reset Address
0x000002
0x000004
0x0001FE
0x000200
User Memory Space
Interrupt Vector Table
User Program
Flash Memory
(175K instructions)
Flash Configuration
Bytes
0x0557EA
0x0557EC
0x0557FE
0x055800
Unimplemented
(Read ‘0’s)
0x7FFFFE
0x800000
Reserved
0x800FF6
0x800FF8
Configuration Memory Space
USERID
Reserved
Write
Latches
0x800FFE
0x801000
0xF9FFFE
0xFA0000
0xFA0002
0xFA0004
Reserved
DEVID
Reserved
0xFEFFFE
0xFF0000
0xFF0002
0xFF0004
0xFFFFFE
Note
1:
Memory areas are not shown to scale.
2:
On reset, these bits are automatically copied into the device Configuration Shadow registers.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 47
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.1.1
PROGRAM MEMORY
ORGANIZATION
4.1.2
All dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices reserve
the addresses between 0x000000 and 0x000200 for
hard-coded program execution vectors. A hardware
Reset vector is provided to redirect code execution
from the default value of the PC on device Reset to the
actual start of code. A GOTO instruction is programmed
by the user application at address 0x000000 of Flash
memory, with the actual address for the start of code at
address 0x000002 of Flash memory.
The program memory space is organized in wordaddressable blocks. Although it is treated as 24 bits
wide, it is more appropriate to think of each address of
the program memory as a lower and upper word, with
the upper byte of the upper word being unimplemented.
The lower word always has an even address, while the
upper word has an odd address (Figure 4-6).
Program memory addresses are always word-aligned
on the lower word, and addresses are incremented or
decremented by two during code execution. This
arrangement provides compatibility with data memory
space addressing and makes data in the program
memory space accessible.
FIGURE 4-6:
msw
Address
least significant word
most significant word
16
8
PC Address
(lsw Address)
0
0x000000
0x000002
0x000004
0x000006
00000000
00000000
00000000
00000000
Program Memory
‘Phantom’ Byte
(read as ‘0’)
DS70657E-page 48
A more detailed discussion of the interrupt vector
tables is provided in Section 7.1 “Interrupt Vector
Table”.
PROGRAM MEMORY ORGANIZATION
23
0x000001
0x000003
0x000005
0x000007
INTERRUPT AND TRAP VECTORS
Instruction Width
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.2
Data Address Space
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X CPU has a
separate 16-bit wide data memory space. The data
space is accessed using separate Address Generation
Units (AGUs) for read and write operations. The data
memory maps, which are presented by device family
and memory size, are shown in Figure 4-7 through
Figure 4-16.
All Effective Addresses (EAs) in the data memory space
are 16 bits wide and point to bytes within the data space.
This arrangement gives a base data space address
range of 8 Kbytes or 4K words.
The base data space address is used in conjunction with
a read or write page register (DSRPAG or DSWPAG) to
form an extended data space, which has a total address
range of 16 MB.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices implement up to
56 Kbytes of data memory. If an EA point to a location
outside of this area, an all-zero word or byte is returned.
4.2.1
DATA SPACE WIDTH
The data memory space is organized in byte
addressable, 16-bit wide blocks. Data is aligned in data
memory and registers as 16-bit words, but all data
space EAs resolve to bytes. The Least Significant
Bytes (LSBs) of each word have even addresses, while
the Most Significant Bytes (MSBs) have odd
addresses.
4.2.2
DATA MEMORY ORGANIZATION
AND ALIGNMENT
All byte loads into any W register are loaded into the
LSB. The MSB is not modified.
A Sign-Extend instruction (SE) is provided to allow user
applications to translate 8-bit signed data to 16-bit
signed values. Alternatively, for 16-bit unsigned data,
user applications can clear the MSB of any W register
by executing a Zero-Extend (ZE) instruction on the
appropriate address.
4.2.3
A data byte read, reads the complete word that
contains the byte, using the LSb of any EA to determine
which byte to select. The selected byte is placed onto
the LSB of the data path. That is, data memory and
registers are organized as two parallel byte-wide
entities with shared (word) address decode but
separate write lines. Data byte writes only write to the
corresponding side of the array or register that matches
the byte address.
SFR SPACE
The first 4 Kbytes of the Near Data Space, from 0x0000
to 0x0FFF, is primarily occupied by Special Function
Registers (SFRs). These are used by the
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X core and peripheral
modules for controlling the operation of the device.
SFRs are distributed among the modules that they
control, and are generally grouped together by module.
Much of the SFR space contains unused addresses;
these are read as ‘0’.
Note:
To maintain backward compatibility with PIC® MCU
devices and improve data space memory usage
efficiency,
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X instruction set supports both word and byte
operations. As a consequence of byte accessibility, all
effective address calculations are internally scaled to
step through word-aligned memory. For example, the
core recognizes that Post-Modified Register Indirect
Addressing mode [Ws++] results in a value of Ws + 1
for byte operations and Ws + 2 for word operations.
© 2011-2012 Microchip Technology Inc.
All word accesses must be aligned to an even address.
Misaligned word data fetches are not supported, so
care must be taken when mixing byte and word
operations, or translating from 8-bit MCU code. If a
misaligned read or write is attempted, an address error
trap is generated. If the error occurred on a read, the
instruction underway is completed. If the error occurred
on a write, the instruction is executed but the write does
not occur. In either case, a trap is then executed,
allowing the system and/or user application to examine
the machine state prior to execution of the address
Fault.
4.2.4
The actual set of peripheral features and
interrupts varies by the device. Refer to
the corresponding device tables and
pinout diagrams for device-specific
information.
NEAR DATA SPACE
The 8 Kbyte area between 0x0000 and 0x1FFF is
referred to as the near data space. Locations in this
space are directly addressable through a 13-bit absolute address field within all memory direct instructions.
Additionally, the whole data space is addressable using
MOV instructions, which support Memory Direct
Addressing mode with a 16-bit address field, or by
using Indirect Addressing mode using a working
register as an Address Pointer.
Preliminary
DS70657E-page 49
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-7:
DATA MEMORY MAP FOR dsPIC33EP32MC20X/50X AND dsPIC33EP32GP50X
DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
X Data RAM (X)
4 Kbyte
SRAM Space
0x17FF
0x1801
0x17FE
0x1800
8 Kbyte
Near
Data
Space
Y Data RAM (Y)
0x1FFF
0x2001
0x1FFE
0x2000
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory Space
(PSV)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
DS70657E-page 50
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-8:
DATA MEMORY MAP FOR dsPIC33EP64MC20X/50X AND dsPIC33EP64GP50X
DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
X Data RAM (X)
8 Kbyte
SRAM Space
0x1FFF
0x2001
8 Kbyte
Near
Data
Space
0x1FFE
0x2000
Y Data RAM (Y)
0x2FFF
0x3001
0x2FFE
0x3000
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory Space
(PSV)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 51
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-9:
DATA MEMORY MAP FOR dsPIC33EP128MC20X/50X AND dsPIC33EP128GP50X
DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
SRAM Space
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
0x1FFF
0x2001
16 Kbyte
LSB
Address
16 bits
X Data RAM (X)
0x2FFF
0x3001
8 Kbyte
Near
Data
Space
0x1FFE
0x2000
0x2FFE
0x3000
Y Data RAM (Y)
0x4FFF
0x5001
0x4FFE
0x5000
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory Space
(PSV)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
DS70657E-page 52
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-10: DATA MEMORY MAP FOR dsPIC33EP256MC20X/50X AND dsPIC33EP256GP50X
DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
SRAM Space
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
0x1FFF
0x2001
32 Kbyte
LSB
Address
16 bits
X Data RAM (X)
0x4FFF
0x5001
0x7FFF
0x8001
0x1FFE
0x2000
0x4FFE
0x5000
Y Data RAM (Y)
0x8FFF
0x9001
0x7FFE
0x8000
0x8FFE
0x9000
Optionally
Mapped
into Program
Memory Space
(PSV)
X Data
Unimplemented (X)
0xFFFF
Note:
8 Kbyte
Near
Data
Space
0xFFFE
Memory areas are not shown to scale.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 53
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-11: DATA MEMORY MAP FOR dsPIC33EP512MC20X/50X AND dsPIC33EP512GP50X
DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFF
0x1001
0x0FFE
0x1000
0x1FFF
0x2001
0x1FFE
0x2000
8 Kbyte
Near
Data
Space
X Data RAM (X)
48 Kbyte
SRAM Space
0x7FFF
0x8001
0x7FFE
0x8000
0x8FFF
0x9001
0x8FFE
0x9000
Y Data RAM (Y)
0xEFFF
0xD001
0xEFFE
0xD000
Optionally
Mapped
into Program
Memory Space
(PSV)
X Data
Unimplemented (X)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
DS70657E-page 54
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-12: DATA MEMORY MAP FOR PIC24EP32GP/MC20X/50X DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
4 Kbyte
8 Kbyte
Near
Data
Space
X Data RAM (X)
SRAM Space
0x1FFF
0x2001
0x1FFE
0x2000
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory Space
(PSV)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 55
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-13: DATA MEMORY MAP FOR PIC24EP64GP/MC20X/50X DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
X Data RAM (X)
8 Kbyte
SRAM Space
0x1FFF
0x2001
0x1FFE
0x2000
0x2FFF
0x3001
0x2FFE
0x3000
0x8001
0x8000
8 Kbyte
Near
Data
Space
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory Space
(PSV)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
DS70657E-page 56
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-14: DATA MEMORY MAP FOR PIC24128GP/MC20X/50X DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
0x1FFF
0x2001
X Data RAM (X)
8 Kbyte
Near
Data
Space
0x1FFE
0x2000
16 Kbyte
SRAM Space
0x4FFF
0x5001
0x4FFE
0x5000
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory Space
(PSV)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 57
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-15: DATA MEMORY MAP FOR PIC24EP256GP/MC20X/50X DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
0x1FFF
0x2001
X Data RAM (X)
8 Kbyte
Near
Data
Space
0x1FFE
0x2000
32 Kbyte
SRAM Space
0x7FFF
0x8001
0x7FFE
0x8000
0x8FFF
0x9001
0x8FFE
0x9000
Optionally
Mapped
into Program
Memory Space
(PSV)
X Data
Unimplemented (X)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
DS70657E-page 58
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-16: DATA MEMORY MAP FOR PIC24EP512GP/MC20X/50X DEVICES
MSB
Address
MSB
4 Kbyte
SFR Space
LSB
Address
16 bits
LSB
0x0000
0x0001
SFR Space
0x0FFE
0x1000
0x0FFF
0x1001
0x1FFF
0x2001
X Data RAM (X)
8 Kbyte
Near
Data
Space
0x1FFE
0x2000
48 Kbyte
SRAM Space
0x7FFF
0x8001
0x7FFE
0x8000
0xEFFF
0xD001
0xEFFE
0xD000
Optionally
Mapped
into Program
Memory Space
(PSV)
X Data
Unimplemented (X)
0xFFFF
Note:
0xFFFE
Memory areas are not shown to scale.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 59
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.2.5
4.3
X AND Y DATA SPACES
The
dsPIC33EPXXXMC20X/50X
and
dsPIC33EPXXXGP50X core has two data spaces, X
and Y. These data spaces can be considered either
separate (for some DSP instructions), or as one unified
linear address range (for MCU instructions). The data
spaces are accessed using two Address Generation
Units (AGUs) and separate data paths. This feature
allows certain instructions to concurrently fetch two
words from RAM, thereby enabling efficient execution
of DSP algorithms such as Finite Impulse Response
(FIR) filtering and Fast Fourier Transform (FFT).
The X data space is used by all instructions and
supports all addressing modes. X data space has
separate read and write data buses. The X read data
bus is the read data path for all instructions that view
data space as combined X and Y address space. It is
also the X data prefetch path for the dual operand DSP
instructions (MAC class).
The Y data space is used in concert with the X data
space by the MAC class of instructions (CLR, ED,
EDAC, MAC, MOVSAC, MPY, MPY.N and MSC) to provide
two concurrent data read paths.
Memory Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
4.3.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 4. “Program Memory” (DS70613)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
Both the X and Y data spaces support Modulo
Addressing mode for all instructions, subject to
addressing
mode
restrictions.
Bit-Reversed
Addressing mode is only supported for writes to X data
space. Modulo Addressing and Bit-Reversed
Addressing are not present in PIC24EPXXXGP/
MC20X devices.
All data memory writes, including in DSP instructions,
view data space as combined X and Y address space.
The boundary between the X and Y data spaces is
device-dependent and is not user-programmable.
DS70657E-page 60
Preliminary
© 2011-2012 Microchip Technology Inc.
Special Function Register Maps
TABLE 4-1:
File Name
Addr.
CPU CORE REGISTER MAP FOR dsPIC33EPXXXMC20X/50X AND dsPIC33EPXXXGP50X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
Preliminary
W0
0000
W0 (WREG)
xxxx
W1
0002
W1
xxxx
W2
0004
W2
xxxx
W3
0006
W3
xxxx
W4
0008
W4
xxxx
W5
000A
W5
xxxx
W6
000C
W6
xxxx
W7
000E
W7
xxxx
W8
0010
W8
xxxx
W9
0012
W9
xxxx
W10
0014
W10
xxxx
W11
0016
W11
xxxx
W12
0018
W12
xxxx
W13
001A
W13
xxxx
W14
001C
W14
xxxx
W15
001E
W15
xxxx
SPLIM
0020
SPLIM
0000
ACCAL
0022
ACCAL
0000
ACCAH
0024
ACCAH
0000
ACCAU
0026
ACCBL
0028
Sign-extension of ACCA<39>
0000
ACCAU
ACCBL
ACCBH
002A
ACCBU
002C
PCL
002E
PCH
0030
—
—
—
—
—
—
DSRPAG
0032
—
—
—
—
—
—
—
—
—
—
—
—
0000
0000
ACCBH
Sign-extension of ACCB<39>
ACCBU
0000
PCL
—
—
—
—
0000
0000
PCH
DSRPAG
0001
DSWPAG
0034
RCOUNT
0036
RCOUNT
0000
DCOUNT
0000
DS70657E-page 61
DCOUNT
0038
DOSTARTL
003A
DOSTARTH
003C
DOENDL
003E
DOENDH
Legend:
—
DSWPAG
0001
DOSTARTL
—
—
—
—
—
—
0040
—
—
—
—
—
—
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
DOENDL
—
—
—
—
—
0000
—
0000
0000
DOSTARTH
DOENDH
0000
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
4.4
File Name
Addr.
CPU CORE REGISTER MAP FOR dsPIC33EPXXXMC20X/50X AND dsPIC33EPXXXGP50X DEVICES ONLY (CONTINUED)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
SA
SB
OAB
SAB
SR
0042
OA
OB
CORCON
0044
VAR
—
MODCON
0046
XMODEN YMODEN
US<1:0>
—
EDT
—
Bit 9
Bit 8
DA
DC
Bit 7
DL<2:0>
Bit 6
IPL2
IPL1
SATA
SATB
BWM<3:0>
Bit 5
Bit 4
IPL0
RA
SATDW ACCSAT
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
0000
N
OV
Z
C
IPL3
SFA
RND
IF
YWM<3:0>
XWM<3:0>
0020
0000
XMODSRT
0048
XMODSRT<15:0>
—
0000
XMODEND
004A
XMODEND<15:0>
—
0001
YMODSRT
004C
YMODSRT<15:0>
—
0000
YMODEND
004E
YMODEND<15:0>
—
XBREV
0050
BREN
DISICNT
0052
—
—
TBLPAG
0054
—
—
MSTRPR
Legend:
XBREV<14:0>
0000
DISICNT<13:0>
—
—
—
—
0058
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
MSTRPR<15:0>
0001
0000
TBLPAG<7:0>
0000
0000
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 62
TABLE 4-1:
File
Name
Addr.
CPU CORE REGISTER MAP FOR PIC24EPXXXGP/MC20X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
Preliminary
W0
0000
W0 (WREG)
xxxx
W1
0002
W1
xxxx
W2
0004
W2
xxxx
W3
0006
W3
xxxx
W4
0008
W4
xxxx
W5
000A
W5
xxxx
W6
000C
W6
xxxx
W7
000E
W7
xxxx
W8
0010
W8
xxxx
W9
0012
W9
xxxx
W10
0014
W10
xxxx
W11
0016
W11
xxxx
W12
0018
W12
xxxx
W13
001A
W13
xxxx
W14
001C
W14
xxxx
W15
001E
W15
xxxx
SPLIM
0020
SPLIM
PCL
002E
PCH
0030
—
—
—
—
—
—
DSRPAG
0032
—
—
—
—
—
—
DSWPAG
0034
—
—
—
—
—
—
RCOUNT
0036
SR
0042
—
—
—
—
—
—
—
DC
IPL2
IPL1
IPL0
RA
N
OV
Z
C
0000
CORCON
0044
VAR
—
—
—
—
—
—
—
—
—
—
—
IPL3
SFA
—
—
0020
DISICNT
0052
—
—
TBLPAG
0054
—
—
—
—
—
—
—
—
MSTRPR
Legend:
0058
0000
PCL
—
—
—
—
PCH
0000
0001
DSRPAG
—
DSWPAG
0001
RCOUNT
0000
DISICNT<13:0>
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
MSTRPR<15:0>
0000
TBLPAG<7:0>
0000
0000
DS70657E-page 63
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-2:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR PIC24EPXXXGP20X DEVICES ONLY
Addr.
Bit 15
Bit 14
Preliminary
© 2011-2012 Microchip Technology Inc.
Bit 13
Bit 12
Bit 11
IFS0
0800
—
IFS1
0802 U2TXIF
IFS2
0804
IFS3
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
DMA1IF
AD1IF
U1TXIF
U1RXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
T3IF
T2IF
OC2IF
IC2IF
DMA2IF
—
—
—
—
—
—
—
—
—
—
—
—
IC4IF
0806
—
—
—
—
—
—
—
—
—
IFS4
0808
—
—
CTMUIF
—
—
—
—
—
IFS8
0810
JTAGIF
ICDIF
—
—
—
—
—
IFS9
0812
—
—
—
—
—
—
—
IEC0
0820
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
IEC1
0822 U2TXIE
IEC2
0824
—
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
—
—
—
—
—
IEC3
0826
—
—
—
—
—
IEC4
0828
—
—
CTMUIE
—
IEC8
0830 JTAGIE
ICDIE
—
IEC9
0832
—
—
—
IPC0
0840
—
Bit 3
Bit 2
DMA0IF
T1IF
OC1IF
INT1IF
CNIF
CMIF
IC3IF
DMA3IF
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PTG3IF
T3IE
T2IE
OC2IE
OC3IE
DMA2IE
—
—
—
—
—
IC4IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
IPC1
0842
IPC2
0844
IPC3
0846
—
IPC4
0848
—
IPC5
084A
—
IPC6
084C
—
T4IP<2:0>
—
OC4IP<2:0>
—
IPC7
084E
—
U2TXIP<2:0>
—
U2RXIP<2:0>
IPC8
0850
—
—
—
—
—
IPC9
0852
—
—
—
—
—
IPC12
0858
—
—
—
—
IPC16
0860
—
IPC19
0866
—
IPC35
0886
—
JTAGID<2:0>
—
ICDIP<2:0>
—
IPC36
0888
—
PTG0IP<2:0>
—
PGWDTIP<2:0>
—
—
—
—
CRCIP<2:0>
—
—
—
IC1IF
INT0IF
0000
MI2C1IF
SI2C1IF
0000
SPI2IF
SPI2EIF
0000
MI2C2IF
SI2C2IF
—
0000
CRCIF
U2EIF
U1EIF
—
0000
—
—
—
—
—
0000
PTG2IF
PTG1IF
PTG0IF
IC2IE
DMA0IE
T1IE
OC1IE
IC1IE
—
INT1IE
CNIE
CMIE
IC3IE
DMA3IE
—
—
—
—
—
—
—
—
—
—
—
—
PTG3IE
PTG2IE
PTGWDTIF PTGSTEPIF
—
0000
INT0IE
0000
MI2C1IE
SI2C1IE
0000
SPI2IE
SPI2EIE
0000
MI2C2IE
SI2C2IE
—
0000
CRCIE
U2EIE
U1EIE
—
0000
—
—
—
—
—
0000
PTG1IE
PTG0IE
PTGWDTIE PTGSTEPIE
—
0000
—
IC2IP<2:0>
—
DMA0IP<2:0>
4444
—
SPI1EIP<2:0>
—
T3IP<2:0>
4444
DMA1IP<2:0>
—
AD1IP<2:0>
—
U1TXIP<2:0>
0444
CMIP<2:0>
—
MI2C1IP<2:0>
—
SI2C1IP<2:0>
4444
—
INT1IP<2:0>
0004
OC3IP<2:0>
—
DMA2IP<2:0>
4444
—
INT2IP<2:0>
—
T5IP<2:0>
4444
—
SPI2IP<2:0>
—
SPI2EIP<2:0>
0044
IC4IP<2:0>
—
IC3IP<2:0>
—
DMA3IP<2:0>
—
MI2C2IP<2:0>
—
SI2C2IP<2:0>
—
—
—
—
0440
—
U2EIP<2:0>
—
U1EIP<2:0>
—
—
—
—
4440
—
CTMUIP<2:0>
—
—
—
—
0040
—
—
—
—
4400
PTGSTEPIP<2:0>
—
—
—
—
4440
PTG2IP<2:0>
—
T2IP<2:0>
U1RXIP<2:0>
—
All
Resets
4444
—
CNIP<2:0>
SPI1IE SPI1EIE
Bit 0
INT0IP<2:0>
—
—
SPI1IF SPI1EIF
Bit 1
—
—
—
Bit 9
IC1IP<2:0>
T1IP<2:0>
—
Bit 10
OC1IP<2:0>
—
—
OC2IP<2:0>
—
SPI1IP<2:0>
—
—
—
—
—
—
—
—
—
—
IPC37
088A
—
—
—
—
—
PTG3IP<2:0>
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
—
—
—
—
—
—
PTG1IP<2:0>
0444
0444
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 64
TABLE 4-3:
File
Name
Addr.
INTERRUPT CONTROLLER REGISTER MAP FOR PIC24EPXXXGP20X DEVICES ONLY (CONTINUED)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
—
—
—
—
STKERR
OSCFAIL
—
0000
INTCON2 08C2
GIE
DISI
SWTRAP
—
—
—
—
—
—
—
—
—
—
INT2EP
INT1EP
INT0EP
8000
INTCON3 08C4
—
—
—
—
—
—
—
—
—
—
DAE
DOOVR
—
—
—
—
0000
INTCON4 08C6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SGHT
INTCON1 08C0 NSTDIS
OVAERR OVBERR
—
—
—
—
ILR<3:0>
INTTREG 08C8
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
DIV0ERR DMACERR MATHERR ADDRERR
VECNUM<7:0>
0000
0000
Preliminary
DS70657E-page 65
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-3:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR PIC24EPXXXMC20X DEVICES ONLY
Addr.
Bit 15
Bit 14
Preliminary
Bit 13
Bit 12
Bit 11
IFS0
0800
—
IFS1
0802 U2TXIF
IFS2
0804
IFS3
© 2011-2012 Microchip Technology Inc.
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
DMA1IF
AD1IF
U1TXIF
U1RXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
T3IF
T2IF
OC2IF
IC2IF
DMA2IF
—
—
—
—
—
—
—
—
—
—
—
—
IC4IF
0806
—
—
—
—
—
—
—
IFS4
0808
—
—
CTMUIF
—
—
—
—
—
IFS5
080A PWM2IF
PWM1IF
—
—
—
—
—
IFS6
080C
—
—
—
—
—
—
IFS8
0810
JTAGIF
ICDIF
—
—
—
IFS9
0812
—
—
—
—
—
IEC0
0820
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
IEC1
0822 U2TXIE
IEC2
0824
—
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
—
—
—
—
—
IEC3
0826
—
—
—
—
—
IEC4
0828
—
—
CTMUIE
—
—
—
IEC5
082A PWM2IE PWM1IE
—
—
—
IEC6
082C
—
—
—
IEC8
0830 JTAGIE
ICDIE
—
IEC9
0832
—
—
—
IPC0
0840
—
IPC1
0842
IPC2
0844
IPC3
0846
—
IPC4
0848
—
IPC5
084A
—
IPC6
084C
—
T4IP<2:0>
—
OC4IP<2:0>
—
IPC7
084E
—
U2TXIP<2:0>
—
U2RXIP<2:0>
IPC8
0850
—
—
—
—
—
IPC9
0852
—
—
—
—
—
IPC12
0858
—
—
—
—
IPC14
085C
—
—
—
—
IPC16
0860
—
IPC19
0866
—
IPC23
086E
—
IPC24
0870
—
IPC35
Legend:
0886
—
JTAGID<2:0>
—
ICDIP<2:0>
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
Bit 0
All
Resets
IC1IF
INT0IF
0000
MI2C1IF
SI2C1IF
0000
SPI2IF
SPI2EIF
0000
MI2C2IF
SI2C2IF
—
0000
CRCIF
U2EIF
U1EIF
—
0000
—
—
—
—
—
0000
—
—
—
—
—
PWM3IF
0000
—
—
—
—
—
—
—
0000
—
PTG3IF
PTG2IF
PTG1IF
PTG0IF
T3IE
T2IE
OC2IE
IC2IE
DMA0IE
T1IE
OC1IE
IC1IE
OC3IE
DMA2IE
—
—
—
INT1IE
CNIE
CMIE
—
—
—
IC4IE
IC3IE
DMA3IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T1IP<2:0>
—
—
T2IP<2:0>
—
U1RXIP<2:0>
—
—
—
CNIP<2:0>
—
—
—
CRCIP<2:0>
—
—
—
PWM2IP<2:0>
—
—
Bit 10
Bit 3
Bit 2
DMA0IF
T1IF
OC1IF
INT1IF
CNIF
CMIF
IC3IF
DMA3IF
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SPI1IF SPI1EIF
QEI1IF PSEMIF
SPI1IE SPI1EIE
QEI1IE PSEMIE
OC1IP<2:0>
—
—
OC2IP<2:0>
—
SPI1IP<2:0>
—
—
Bit 1
PTGWDTIF PTGSTEPIF
—
0000
INT0IE
0000
MI2C1IE
SI2C1IE
0000
SPI2IE
SPI2EIE
0000
MI2C2IE
SI2C2IE
—
0000
CRCIE
U2EIE
U1EIE
—
0000
—
—
—
—
—
0000
—
—
—
—
—
PWM3IE
0000
—
—
—
—
—
—
—
0000
PTG3IE
PTG2IE
PTG1IE
PTG0IE
PTGWDTIE PTGSTEPIE
—
0000
IC1IP<2:0>
—
INT0IP<2:0>
4444
—
IC2IP<2:0>
—
DMA0IP<2:0>
4444
—
SPI1EIP<2:0>
—
T3IP<2:0>
4444
DMA1IP<2:0>
—
AD1IP<2:0>
—
U1TXIP<2:0>
0444
CMIP<2:0>
—
MI2C1IP<2:0>
—
SI2C1IP<2:0>
4444
—
INT1IP<2:0>
0004
OC3IP<2:0>
—
DMA2IP<2:0>
4444
—
INT2IP<2:0>
—
T5IP<2:0>
4444
—
SPI2IP<2:0>
—
SPI2EIP<2:0>
0044
IC4IP<2:0>
—
IC3IP<2:0>
—
DMA3IP<2:0>
0444
—
MI2C2IP<2:0>
—
SI2C2IP<2:0>
—
—
—
—
0440
—
QEI1IP<2:0>
—
PSEMIP<2:0>
—
—
—
—
0440
—
U2EIP<2:0>
—
U1EIP<2:0>
—
—
—
—
4440
—
CTMUIP<2:0>
—
—
—
—
0040
—
—
—
4400
—
—
—
—
—
—
—
Bit 9
—
—
—
—
—
—
—
PWM1IP<2:0>
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PWM3IP<2:0>
—
—
4004
—
4400
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 66
TABLE 4-4:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR PIC24EPXXXMC20X DEVICES ONLY (CONTINUED)
Addr.
Bit 15
IPC36
0888
—
IPC37
088A
—
INTCON1 08C0 NSTDIS
Bit 14
Bit 13
Bit 12
PTG0IP<2:0>
—
—
OVAERR OVBERR
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
—
—
PGWDTIP<2:0>
—
PTGSTEPIP<2:0>
—
—
—
PTG3IP<2:0>
—
PTG2IP<2:0>
—
—
—
—
—
—
—
DIV0ERR DMACERR MATHERR ADDRERR
Bit 1
Bit 0
All
Resets
—
—
4440
0444
PTG1IP<2:0>
STKERR
OSCFAIL
—
0000
INTCON2 08C2
GIE
DISI
SWTRAP
—
—
—
—
—
—
—
—
—
—
INT2EP
INT1EP
INT0EP
8000
INTCON3 08C4
—
—
—
—
—
—
—
—
—
—
DAE
DOOVR
—
—
—
—
0000
INTCON4 08C6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SGHT
INTTREG 08C8
—
—
—
—
ILR<3:0>
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
VECNUM<7:0>
0000
0000
Preliminary
DS70657E-page 67
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-4:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXGP50X DEVICES ONLY
Addr.
Bit 15
Bit 14
Preliminary
© 2011-2012 Microchip Technology Inc.
Bit 13
Bit 12
Bit 11
IFS0
0800
—
IFS1
0802 U2TXIF
IFS2
0804
IFS3
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
DMA1IF
AD1IF
U1TXIF
U1RXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
T3IF
T2IF
OC2IF
IC2IF
DMA2IF
—
—
—
DMA0IF
T1IF
OC1IF
INT1IF
CNIF
CMIF
—
—
—
—
—
—
—
—
—
IC4IF
IC3IF
DMA3IF
C1IF
C1RXIF
0806
—
—
—
—
—
—
—
—
—
—
—
—
—
IFS4
0808
—
—
CTMUIF
—
—
—
—
—
—
C1TXIF
—
—
IFS6
080C
—
—
—
—
—
—
—
—
—
—
—
IFS8
0810
JTAGIF
ICDIF
—
—
—
—
—
—
—
—
IFS9
0812
—
—
—
—
—
—
—
—
—
IEC0
0820
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
T3IE
T2IE
IEC1
0822 U2TXIE
IEC2
0824
—
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
—
—
—
—
—
OC3IE
DMA2IE
—
—
—
—
—
IC4IE
IEC3
0826
—
—
—
—
—
—
—
—
—
—
IEC4
0828
—
—
CTMUIE
—
—
—
—
—
—
IEC8
0830 JTAGIE
ICDIE
—
—
—
—
—
—
IEC9
0832
—
—
—
—
—
—
—
—
IPC0
0840
—
IPC1
0842
IPC2
0844
IPC3
0846
—
IPC4
0848
—
IPC5
084A
—
IPC6
084C
—
T4IP<2:0>
—
OC4IP<2:0>
—
IPC7
084E
—
U2TXIP<2:0>
—
U2RXIP<2:0>
IPC8
0850
—
C1IP<2:0>
—
IPC9
0852
—
—
—
—
—
IPC11
0856
—
—
—
—
—
IPC12
0858
—
—
—
—
—
MI2C2IP<2:0>
—
IPC16
0860
—
—
U2EIP<2:0>
—
IPC17
0862
—
—
—
—
—
C1TXIP<2:0>
—
IPC19
0866
—
—
—
—
—
IPC35
0886
—
JTAGID<2:0>
—
ICDIP<2:0>
—
IPC36
0888
—
PTG0IP<2:0>
—
PGWDTIP<2:0>
—
—
T1IP<2:0>
—
—
T2IP<2:0>
—
U1RXIP<2:0>
—
—
—
CNIP<2:0>
—
—
—
CRCIP<2:0>
Bit 10
Bit 9
SPI1IF SPI1EIF
SPI1IE SPI1EIE
Bit 0
All
Resets
IC1IF
INT0IF
0000
MI2C1IF
SI2C1IF
0000
SPI2IF
SPI2EIF
0000
MI2C2IF
SI2C2IF
—
0000
CRCIF
U2EIF
U1EIF
—
0000
—
—
—
—
PWM3IF
0000
—
—
—
—
—
—
0000
PTG3IF
PTG2IF
PTG1IF
PTG0IF
OC2IE
IC2IE
DMA0IE
T1IE
—
INT1IE
IC3IE
DMA3IE
—
C1TXIE
—
—
OC1IP<2:0>
—
—
OC2IP<2:0>
—
SPI1IP<2:0>
—
—
—
—
—
—
Bit 1
PTGWDTIF PTGSTEPIF
—
0000
INT0IE
0000
OC1IE
IC1IE
CNIE
CMIE
MI2C1IE
SI2C1IE
0000
C1IE
C1RXIE
SPI2IE
SPI2EIE
0000
—
—
MI2C2IE
SI2C2IE
—
0000
—
—
CRCIE
U2EIE
U1EIE
—
0000
—
—
—
—
—
—
—
0000
PTG3IE
PTG2IE
PTG1IE
PTG0IE
PTGWDTIE PTGSTEPIE
—
0000
IC1IP<2:0>
—
INT0IP<2:0>
4444
—
IC2IP<2:0>
—
DMA0IP<2:0>
4444
—
SPI1EIP<2:0>
—
T3IP<2:0>
4444
DMA1IP<2:0>
—
AD1IP<2:0>
—
U1TXIP<2:0>
0444
CMIP<2:0>
—
MI2C1IP<2:0>
—
SI2C1IP<2:0>
4444
—
INT1IP<2:0>
0004
OC3IP<2:0>
—
DMA2IP<2:0>
4444
—
INT2IP<2:0>
—
T5IP<2:0>
4444
C1RXIP<2:0>
—
SPI2IP<2:0>
—
SPI2EIP<2:0>
4444
IC4IP<2:0>
—
IC3IP<2:0>
—
DMA3IP<2:0>
—
—
—
IPC37
088A
—
—
—
—
—
PTG3IP<2:0>
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
SI2C2IP<2:0>
—
—
—
—
0440
U1EIP<2:0>
—
—
—
—
4440
—
—
—
—
0400
—
—
—
—
0040
—
—
—
—
4400
PTGSTEPIP<2:0>
—
—
—
—
4440
PTG2IP<2:0>
—
—
—
—
CTMUIP<2:0>
—
0444
—
—
—
—
PTG1IP<2:0>
0444
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 68
TABLE 4-5:
File
Name
Addr.
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXGP50X DEVICES ONLY (CONTINUED)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
STKERR
OSCFAIL
—
0000
INTCON2 08C2
GIE
DISI
SWTRAP
—
—
—
—
—
—
—
—
—
—
INT2EP
INT1EP
INT0EP
8000
INTCON3 08C4
—
—
—
—
—
—
—
—
—
—
DAE
DOOVR
—
—
—
—
0000
INTCON4 08C6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SGHT
INTCON1 08C0 NSTDIS
OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
—
—
—
—
ILR<3:0>
INTTREG 08C8
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR
VECNUM<7:0>
0000
0000
Preliminary
DS70657E-page 69
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-5:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMC20X DEVICES ONLY
Addr.
Bit 15
Bit 14
Preliminary
Bit 13
Bit 12
Bit 11
IFS0
0800
—
IFS1
0802 U2TXIF
IFS2
0804
IFS3
© 2011-2012 Microchip Technology Inc.
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
DMA1IF
AD1IF
U1TXIF
U1RXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
T3IF
T2IF
OC2IF
IC2IF
DMA2IF
—
—
—
—
—
—
—
—
—
—
—
—
IC4IF
0806
—
—
—
—
—
—
—
IFS4
0808
—
—
CTMUIF
—
—
—
—
—
IFS5
080A PWM2IF
PWM1IF
—
—
—
—
—
IFS6
080C
—
—
—
—
—
—
IFS8
0810
JTAGIF
ICDIF
—
—
—
IFS9
0812
—
—
—
—
—
IEC0
0820
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
IEC1
0822 U2TXIE
IEC2
0824
—
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
—
—
—
—
—
IEC3
0826
—
—
—
—
—
IEC4
0828
—
—
CTMUIE
—
—
—
IEC5
082A PWM2IE PWM1IE
—
—
—
IEC6
082C
—
—
—
IEC8
0830 JTAGIE
ICDIE
—
IEC9
0832
—
—
—
IPC0
0840
—
IPC1
0842
IPC2
0844
IPC3
0846
—
IPC4
0848
—
IPC5
084A
—
IPC6
084C
—
T4IP<2:0>
—
OC4IP<2:0>
—
IPC7
084E
—
U2TXIP<2:0>
—
U2RXIP<2:0>
IPC8
0850
—
—
—
—
—
IPC9
0852
—
—
—
—
IPC12
0858
—
—
—
IPC14
085C
—
—
—
IPC16
0860
—
IPC19
0866
—
IPC23
086E
—
IPC24
0870
—
IPC35
Legend:
0886
—
JTAGID<2:0>
—
ICDIP<2:0>
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
Bit 0
All
Resets
IC1IF
INT0IF
0000
MI2C1IF
SI2C1IF
0000
SPI2IF
SPI2EIF
0000
MI2C2IF
SI2C2IF
—
0000
CRCIF
U2EIF
U1EIF
—
0000
—
—
—
—
—
0000
—
—
—
—
—
PWM3IF
0000
—
—
—
—
—
—
—
0000
—
PTG3IF
PTG2IF
PTG1IF
PTG0IF
T3IE
T2IE
OC2IE
IC2IE
DMA0IE
T1IE
OC1IE
IC1IE
OC3IE
DMA2IE
—
—
—
INT1IE
CNIE
CMIE
—
—
—
IC4IE
IC3IE
DMA3IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T1IP<2:0>
—
—
T2IP<2:0>
—
U1RXIP<2:0>
—
—
—
—
—
Bit 2
DMA0IF
T1IF
OC1IF
INT1IF
CNIF
CMIF
IC3IF
DMA3IF
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SPI1IF SPI1EIF
QEI1IF PSEMIF
SPI1IE SPI1EIE
QEI1IE PSEMIE
OC2IP<2:0>
—
SPI1IP<2:0>
—
—
0000
MI2C1IE
SI2C1IE
0000
SPI2IE
SPI2EIE
0000
MI2C2IE
SI2C2IE
—
0000
CRCIE
U2EIE
U1EIE
—
0000
—
—
—
—
—
0000
—
—
—
—
—
PWM3IE
0000
—
—
—
—
—
—
—
0000
PTG3IE
PTG2IE
PTG1IE
PTG0IE
PTGWDTIE PTGSTEPIE
—
0000
IC2IP<2:0>
—
DMA0IP<2:0>
4444
—
SPI1EIP<2:0>
—
T3IP<2:0>
4444
DMA1IP<2:0>
—
AD1IP<2:0>
—
U1TXIP<2:0>
0444
CMIP<2:0>
—
MI2C1IP<2:0>
—
SI2C1IP<2:0>
4444
—
INT1IP<2:0>
0004
OC3IP<2:0>
—
DMA2IP<2:0>
4444
—
INT2IP<2:0>
—
T5IP<2:0>
4444
C1RXIP<2:0>
—
SPI2IP<2:0>
—
SPI2EIP<2:0>
0444
—
IC4IP<2:0>
—
IC3IP<2:0>
—
DMA3IP<2:0>
—
—
MI2C2IP<2:0>
—
SI2C2IP<2:0>
—
—
—
—
0440
—
—
QEI1IP<2:0>
—
PSEMIP<2:0>
—
—
—
—
0440
—
U2EIP<2:0>
—
U1EIP<2:0>
—
—
—
—
4440
—
CTMUIP<2:0>
—
—
—
—
0040
—
—
—
4400
—
—
0000
INT0IE
—
—
—
—
PTGWDTIF PTGSTEPIF
4444
—
OC1IP<2:0>
Bit 1
INT0IP<2:0>
PWM2IP<2:0>
—
Bit 3
—
CRCIP<2:0>
—
Bit 9
IC1IP<2:0>
CNIP<2:0>
—
Bit 10
—
—
—
—
—
—
—
—
—
—
—
PWM1IP<2:0>
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0444
0004
PWM3IP<2:0>
—
—
—
4400
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 70
TABLE 4-6:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMC20X DEVICES ONLY (CONTINUED)
Addr.
Bit 15
IPC36
0888
—
IPC37
088A
—
INTCON1 08C0 NSTDIS
Bit 14
Bit 13
Bit 12
PTG0IP<2:0>
—
—
—
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
—
—
PGWDTIP<2:0>
—
PTGSTEPIP<2:0>
—
—
PTG3IP<2:0>
—
PTG2IP<2:0>
—
OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR
Bit 1
Bit 0
All
Resets
—
—
4440
PTG1IP<2:0>
0444
STKERR
OSCFAIL
—
0000
INTCON2 08C2
GIE
DISI
SWTRAP
—
—
—
—
—
—
—
—
—
—
INT2EP
INT1EP
INT0EP
8000
INTCON3 08C4
—
—
—
—
—
—
—
—
—
—
DAE
DOOVR
—
—
—
—
0000
INTCON4 08C6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SGHT
—
—
—
—
ILR<3:0>
INTTREG 08C8
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
VECNUM<7:0>
0000
0000
Preliminary
DS70657E-page 71
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-6:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMC50X DEVICES ONLY
Addr.
Bit 15
Bit 14
Preliminary
Bit 13
Bit 12
Bit 11
IFS0
0800
—
IFS1
0802 U2TXIF
IFS2
0804
IFS3
© 2011-2012 Microchip Technology Inc.
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 0
All
Resets
DMA1IF
AD1IF
U1TXIF
U1RXIF
U2RXIF
INT2IF
T5IF
T4IF
OC4IF
OC3IF
T3IF
T2IF
OC2IF
IC2IF
DMA2IF
—
—
—
IC1IF
INT0IF
0000
MI2C1IF
SI2C1IF
—
—
—
—
—
—
—
—
—
IC4IF
0000
SPI2IF
SPI2EIF
0806
—
—
—
—
—
—
—
0000
MI2C2IF
SI2C2IF
—
IFS4
0808
—
—
CTMUIF
—
—
—
—
—
0000
CRCIF
U2EIF
U1EIF
—
IFS5
080A PWM2IF
PWM1IF
—
—
—
—
—
0000
—
—
—
—
—
IFS6
080C
—
—
—
—
—
—
0000
—
—
—
—
—
PWM3IF
IFS8
0810
JTAGIF
ICDIF
—
—
—
0000
—
—
—
—
—
—
—
IFS9
0812
—
—
—
—
—
0000
—
PTG3IF
PTG2IF
PTG1IF
PTG0IF
IEC0
0820
—
DMA1IE
AD1IE
U1TXIE
U1RXIE
T3IE
T2IE
OC2IE
IC2IE
DMA0IE
T1IE
IEC1
0822 U2TXIE
IEC2
0824
—
U2RXIE
INT2IE
T5IE
T4IE
OC4IE
—
—
—
—
—
OC3IE
DMA2IE
—
—
—
INT1IE
—
—
—
IC4IE
IC3IE
DMA3IE
IEC3
0826
—
—
—
—
—
—
—
—
—
IEC4
0828
—
—
CTMUIE
—
—
—
—
—
—
C1TXIE
IEC5
082A PWM2IE PWM1IE
—
—
—
—
—
—
—
IEC6
082C
—
—
—
—
—
—
—
—
IEC7
082E
—
—
—
—
—
—
—
IEC8
0830 JTAGIE
ICDIE
—
—
—
—
IEC9
0832
—
—
—
—
—
—
IPC0
0840
—
IPC1
0842
IPC2
0844
IPC3
0846
—
IPC4
0848
—
IPC5
084A
—
IPC6
084C
—
T4IP<2:0>
—
OC4IP<2:0>
—
IPC7
084E
—
U2TXIP<2:0>
—
U2RXIP<2:0>
IPC8
0850
—
C1IP<2:0>
—
IPC9
0852
—
—
—
—
IPC12
0858
—
—
—
—
IPC14
085C
—
—
—
—
IPC16
0860
—
IPC17
0862
—
—
—
IPC19
0866
—
—
—
T1IP<2:0>
—
—
T2IP<2:0>
—
U1RXIP<2:0>
—
—
—
Bit 9
Bit 3
Bit 2
DMA0IF
T1IF
OC1IF
INT1IF
CNIF
CMIF
IC3IF
DMA3IF
C1IF
C1RXIF
—
—
—
—
—
C1TXIF
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SPI1IF SPI1EIF
QEI1IF PSEMIF
SPI1IE SPI1EIE
Bit 1
PTGWDTIF PTGSTEPIF
—
0000
INT0IE
0000
OC1IE
IC1IE
CNIE
CMIE
MI2C1IE
SI2C1IE
0000
C1IE
C1RXIE
SPI2IE
SPI2EIE
0000
—
—
MI2C2IE
SI2C2IE
—
0000
—
—
CRCIE
U2EIE
U1EIE
—
0000
—
—
—
—
—
—
—
0000
—
—
—
—
—
—
—
PWM3IE
0000
—
—
—
—
—
—
—
—
—
0000
—
—
—
—
—
—
—
—
—
—
0000
—
—
—
PTG3IE
PTG2IE
PTG1IE
PTG0IE
QEI1IE PSEMIE
4444
—
IC2IP<2:0>
—
DMA0IP<2:0>
4444
—
SPI1EIP<2:0>
—
T3IP<2:0>
4444
DMA1IP<2:0>
—
AD1IP<2:0>
—
U1TXIP<2:0>
0444
CMIP<2:0>
—
MI2C1IP<2:0>
—
SI2C1IP<2:0>
4444
—
INT1IP<2:0>
0004
OC3IP<2:0>
—
DMA2IP<2:0>
4444
—
INT2IP<2:0>
—
T5IP<2:0>
4444
C1RXIP<2:0>
—
SPI2IP<2:0>
—
SPI2EIP<2:0>
4444
—
IC4IP<2:0>
—
IC3IP<2:0>
—
—
MI2C2IP<2:0>
—
SI2C2IP<2:0>
—
—
—
—
0440
—
QEI1IP<2:0>
—
PSEMIP<2:0>
—
—
—
—
0440
—
U2EIP<2:0>
—
U1EIP<2:0>
—
—
—
—
4440
—
—
C1TXIP<2:0>
—
—
—
—
—
0400
—
—
—
—
—
—
0040
—
—
—
—
4400
CRCIP<2:0>
—
OC2IP<2:0>
—
SPI1IP<2:0>
—
—
0000
INT0IP<2:0>
—
—
—
—
—
OC1IP<2:0>
PTGWDTIE PTGSTEPIE
IC1IP<2:0>
CNIP<2:0>
—
Bit 10
—
—
—
—
—
IPC23
086E
—
PWM2IP<2:0>
—
PWM1IP<2:0>
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
—
—
—
—
—
—
—
CTMUIP<2:0>
—
—
—
DMA3IP<2:0>
0444
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 72
TABLE 4-7:
File
Name
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33EPXXXMC50X DEVICES ONLY (CONTINUED)
Addr.
Bit 15
Bit 14
IPC24
0870
—
—
IPC35
0886
—
JTAGID<2:0>
—
ICDIP<2:0>
IPC36
0888
—
PTG0IP<2:0>
—
PGWDTIP<2:0>
—
IPC37
088A
—
—
PTG3IP<2:0>
—
INTCON1 08C0 NSTDIS
—
Bit 13
Bit 12
Bit 11
Bit 10
—
—
—
—
—
—
OVAERR OVBERR COVAERR COVBERR OVATE
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
4400
PTGSTEPIP<2:0>
—
—
—
—
4440
PTG2IP<2:0>
—
OVBTE
COVTE SFTACERR DIV0ERR DMACERR MATHERR ADDRERR
Bit 2
Bit 1
Bit 0
PWM3IP<2:0>
All
Resets
0004
0444
PTG1IP<2:0>
STKERR
OSCFAIL
—
0000
INTCON2 08C2
GIE
DISI
SWTRAP
—
—
—
—
—
—
—
—
—
—
INT2EP
INT1EP
INT0EP
8000
INTCON3 08C4
—
—
—
—
—
—
—
—
—
—
DAE
DOOVR
—
—
—
—
0000
INTCON4 08C6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SGHT
INTTREG 08C8
—
—
—
—
ILR<3:0>
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
VECNUM<7:0>
0000
0000
Preliminary
DS70657E-page 73
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-7:
SFR Name Addr.
TIMER1 THROUGH TIMER5 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
Preliminary
TMR1
0100
Timer1 Register
PR1
0102
Period Register 1
T1CON
0104
TMR2
0106
Timer2 Register
TMR3HLD
0108
Timer3 Holding Register (for 32-bit timer operations only)
xxxx
TMR3
010A
Timer3 Register
xxxx
PR2
010C
Period Register 2
FFFF
PR3
010E
Period Register 3
T2CON
0110
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
T32
—
TCS
—
T3CON
0112
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
—
—
TCS
—
TMR4
0114
Timer4 Register
TMR5HLD
0116
Timer5 Holding Register (for 32-bit operations only)
xxxx
TMR5
0118
Timer5 Register
xxxx
PR4
011A
Period Register 4
FFFF
PR5
011C
Period Register 5
T4CON
011E
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
T32
—
TCS
—
0000
T5CON
0120
TON
—
TSIDL
—
—
—
—
—
—
TGATE
TCKPS<1:0>
—
—
TCS
—
0000
Legend:
TON
—
TSIDL
—
—
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
xxxx
FFFF
TGATE
TCKPS<1:0>
—
TSYNC
TCS
—
0000
xxxx
FFFF
0000
0000
xxxx
FFFF
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 74
TABLE 4-8:
File Name Addr.
INPUT CAPTURE 1 THROUGH INPUT CAPTURE 4 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
ICOV
ICBNE
Bit 1
Bit 0
All
Resets
Preliminary
IC1CON1
0140
—
—
ICSIDL
IC1CON2
0142
—
—
—
IC1BUF
0144
Input Capture 1 Buffer Register
IC1TMR
0146
Input Capture 1 Timer
IC2CON1
0148
—
—
ICSIDL
IC2CON2
014A
—
—
—
IC2BUF
014C
Input Capture 2 Buffer Register
IC2TMR
014E
Input Capture 2 Timer
IC3CON1
0150
—
—
ICSIDL
IC3CON2
0152
—
—
—
IC3BUF
0154
Input Capture 3 Buffer Register
IC3TMR
0156
Input Capture 3 Timer
IC4CON1
0158
—
—
ICSIDL
IC4CON2
015A
—
—
—
IC4BUF
015C
Input Capture 4 Buffer Register
xxxx
IC4TMR
015E
Input Capture 4 Timer
0000
Legend:
ICTSEL<2:0>
—
—
—
ICTSEL<2:0>
—
—
—
—
—
—
IC32
ICTRIG
—
—
—
ICTSEL<2:0>
—
—
—
—
ICTSEL<2:0>
—
—
—
—
—
—
—
—
IC32
ICTRIG
—
—
IC32
ICTRIG
—
—
IC32
ICTRIG
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
ICI<1:0>
TRIGSTAT
—
ICM<2:0>
SYNCSEL<4:0>
0000
000D
xxxx
0000
ICI<1:0>
TRIGSTAT
ICOV
—
ICBNE
ICM<2:0>
SYNCSEL<4:0>
0000
000D
xxxx
0000
ICI<1:0>
TRIGSTAT
ICOV
—
ICBNE
ICM<2:0>
SYNCSEL<4:0>
0000
000D
xxxx
0000
ICI<1:0>
TRIGSTAT
ICOV
—
ICBNE
ICM<2:0>
SYNCSEL<4:0>
0000
000D
DS70657E-page 75
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-9:
File Name
Addr.
OUTPUT COMPARE 1 THROUGH OUTPUT COMPARE 4 REGISTER MAP
Bit 15
Bit 14
Bit 13
—
OCSIDL
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
—
ENFLTB
—
OC32
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
ENFLTA
—
OCFLTB
OCFLTA
TRIGMODE
OCTRIG
TRIGSTAT
OCTRIS
Bit 1
Bit 0
All
Resets
Preliminary
OC1CON1
0900
—
OC1CON2
0902
FLTMD
OC1RS
0904
Output Compare 1 Secondary Register
xxxx
OC1R
0906
Output Compare 1 Register
xxxx
OC1TMR
0908
Timer Value 1 Register
OC2CON1
090A
—
OC2CON2
090C
FLTMD
OC2RS
090E
Output Compare 2 Secondary Register
xxxx
OC2R
0910
Output Compare 2 Register
xxxx
OC2TMR
0912
Timer Value 2 Register
OC3CON1
0914
—
OC3CON2
0916
FLTMD
OC3RS
0918
Output Compare 3 Secondary Register
xxxx
OC3R
091A
Output Compare 3 Register
xxxx
OC3TMR
091C
Timer Value 3 Register
OC4CON1
091E
—
OC4CON2
0920
FLTMD
OC4RS
0922
Output Compare 4 Secondary Register
xxxx
OC4R
0924
Output Compare 4 Register
xxxx
OC4TMR
0926
Timer Value 4 Register
xxxx
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
FLTOUT FLTTRIEN
—
OCSIDL
FLTOUT FLTTRIEN
—
OCINV
—
—
—
OCTSEL<2:0>
OCINV
OCSIDL
FLTOUT FLTTRIEN
—
OCTSEL<2:0>
OCSIDL
FLTOUT FLTTRIEN
—
OCTSEL<2:0>
OCINV
—
—
OCTSEL<2:0>
OCINV
—
—
OCM<2:0>
SYNCSEL<4:0>
0000
000C
xxxx
—
ENFLTB
ENFLTA
—
OCFLTB
—
OC32
OCTRIG
TRIGSTAT
OCTRIS
OCFLTA
TRIGMODE
OCM<2:0>
SYNCSEL<4:0>
0000
000C
xxxx
—
ENFLTB
ENFLTA
—
OCFLTB
—
OC32
OCTRIG
TRIGSTAT
OCTRIS
OCFLTA
TRIGMODE
OCM<2:0>
SYNCSEL<4:0>
0000
000C
xxxx
ENFLTC
ENFLTB
ENFLTA
OCFLTC
OCFLTB
—
OC32
OCTRIG
TRIGSTAT
OCTRIS
OCFLTA
TRIGMODE
OCM<2:0>
SYNCSEL<4:0>
0000
000C
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 76
TABLE 4-10:
File Name
PTG REGISTER MAP
Bit 14
Bit 15
PTGCST
0AC0
PTGEN
PTGCON
0AC2
PTGBTE
0AC4
PTGBTE<15:0>
0000
PTGHOLD
0AC6
PTGHOLD<15:0>
0000
PTGT0LIM
0AC8
PTGT0LIM<15:0>
0000
PTGT1LIM
0ACA
PTGT1LIM<15:0>
0000
PTGSDLIM 0ACC
PTGSDLIM<15:0>
0000
PTGC0LIM
0ACE
PTGC0LIM<15:0>
0000
PTGC1LIM
0AD0
PTGC1LIM<15:0>
0000
PTGADJ
0AD2
PTGADJ<15:0>
0000
PTGL0
0AD4
PTGL0<15:0>
PTGQPTR
0AD6
—
Bit 13
Bit 12
PTGSIDL PTGTOGL
Bit 11
—
PTGCLK<2:0>
—
—
Bit 10
Bit 9
PTGSWT
—
Bit 8
Bit 7
PTGIVIS PTGSTRT PTGWTO
PTGDIV<4:0>
—
—
—
—
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
—
—
—
—
PTGPWD<3:0>
—
—
—
Bit 1
Bit 0
All
Resets
Addr.
PTGITM<1:0>
PTGWDT<2:0>
0000
0000
0000
—
—
—
PTGQPTR<4:0>
0000
Preliminary
PTGQUE0
0AD8
STEP1<7:0>
STEP0<7:0>
0000
PTGQUE1
0ADA
STEP3<7:0>
STEP2<7:0>
0000
PTGQUE2
0ADC
STEP5<7:0>
STEP4<7:0>
0000
PTGQUE3
0ADE
STEP7<7:0>
STEP6<7:0>
0000
PTGQUE4
0AE0
STEP9<7:0>
STEP8<7:0>
0000
PTGQUE5
0AE2
STEP11<7:0>
STEP10<7:0>
0000
PTGQUE6
0AE4
STEP13<7:0>
STEP12<7:0>
0000
PTGQUE7
0AE6
STEP15<7:0>
STEP14<7:0>
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
DS70657E-page 77
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-11:
File Name
PWM REGISTER MAP FOR dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
PTCON
0C00
PTEN
—
PTSIDL
SESTAT
SEIEN
EIPU
PTCON2
0C02
—
—
—
—
—
—
PTPER
0C04
PTPER<15:0>
00F8
SEVTCMP
0C06
SEVTCMP<15:0>
0000
MDC
0C0A
MDC<15:0>
CHOP
0C1A CHPCLKEN
PWMKEY
Legend:
—
—
—
—
Bit 9
Bit 8
Bit 7
SYNCPOL SYNCOEN SYNCEN
—
—
Bit 4
Bit 3
SYNCSRC<2:0>
—
—
—
Bit 2
Bit 1
Bit 0
SEVTPS<3:0>
—
—
0000
PCLKDIV<2:0>
0000
0000
—
CHOPCLK<9:0>
0C1E
0000
PWMKEY<15:0>
0000
PWM GENERATOR 1 REGISTER MAP FOR dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY
Preliminary
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
PWMCON1
0C20
FLTSTAT
CLSTAT
TRGSTAT
FLTIEN
CLIEN
TRGIEN
IOCON1
0C22
PENH
PENL
POLH
POLL
FCLCON1
0C24
—
PMOD<1:0>
CLSRC<4:0>
Bit 9
Bit 8
Bit 7
Bit 6
ITB
MDCS
DTC<1:0>
OVRENH
OVRENL
OVRDAT<1:0>
CLPOL
CLMOD
0C26
PDC1<15:0>
PHASE1
0C28
PHASE1<15:0>
DTR1
0C2A
—
—
ALTDTR1
0C2C
—
—
TRIG1
0C32
TRGCON1
0C34
Bit 0
All
Resets
XPRES
IUE
0000
SWAP
OSYNC
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
DTCP
—
MTBS
CAM
CLDAT<1:0>
FLTDAT<1:0>
FLTSRC<4:0>
PDC1
FLTPOL
FLTMOD<1:0>
—
TRGDIV<3:0>
0C3A
PHR
PHF
PLR
PLF
LEBDLY1
0C3C
—
—
—
—
0C3E
—
—
—
—
—
FLTLEBEN CLLEBEN
0000
DTR1<13:0>
0000
ALTDTR1<13:0>
0000
0000
—
—
—
—
—
—
—
—
TRGSTRT<5:0>
BCH
BCL
BPHH
BPHL
0000
BPLH
BPLL
LEB<11:0>
BLANKSEL<3:0>
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
0000
FFF8
TRGCMP<15:0>
LEBCON1
Legend:
Bit 5
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-13:
AUXCON1
Bit 6
All
Resets
Addr.
—
—
0000
0000
CHOPCLK<3:0>
CHOPHEN CHOPLEN
0000
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 78
TABLE 4-12:
PWM GENERATOR 2 REGISTER MAP FOR dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
PWMCON2
0C40
FLTSTAT
CLSTAT
TRGSTAT
FLTIEN
CLIEN
TRGIEN
IOCON2
0C42
PENH
PENL
POLH
POLL
FCLCON2
0C44
—
PDC2
0C46
PDC2<15:0>
PHASE2
0C48
PHASE2<15:0>
DTR2
0C4A
—
—
ALTDTR2
0C4C
—
—
TRIG2
0C52
TRGCON2
0C54
CLSRC<4:0>
Bit 8
Bit 7
—
TRGDIV<3:0>
0C5A
PHR
PHF
PLR
PLF
LEBDLY2
0C5C
—
—
—
—
AUXCON2
0C5E
—
—
—
—
ITB
MDCS
DTC<1:0>
OVRENH
OVRENL
OVRDAT<1:0>
CLPOL
CLMOD
—
FLTLEBEN CLLEBEN
All
Resets
XPRES
IUE
0000
SWAP
OSYNC
0000
Bit 4
Bit 3
Bit 2
Bit 1
DTCP
—
MTBS
CAM
CLDAT<1:0>
FLTDAT<1:0>
FLTSRC<4:0>
FLTPOL
FLTMOD<1:0>
00F8
0000
0000
DTR2<13:0>
0000
ALTDTR2<13:0>
0000
0000
—
—
—
—
—
—
—
TRGSTRT<5:0>
—
BCH
BCL
BPHH
BPHL
0000
BPLH
BPLL
LEB<11:0>
BLANKSEL<3:0>
—
0000
0000
—
CHOPSEL<3:0>
CHOPHEN CHOPLEN
0000
Preliminary
PWM GENERATOR 3 REGISTER MAP FOR dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY
File Name
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
PWMCON3
0C60
FLTSTAT
CLSTAT
TRGSTAT
FLTIEN
CLIEN
TRGIEN
IOCON3
0C62
PENH
PENL
POLH
POLL
FCLCON3
0C64
—
PMOD<1:0>
CLSRC<4:0>
Bit 9
Bit 8
Bit 7
ITB
MDCS
DTC<1:0>
OVRENL
OVRDAT<1:0>
CLPOL
CLMOD
0C66
PDC3<15:0>
0C68
PHASE3<15:0>
DTR3
0C6A
—
—
—
—
ALTDTR3
0C6C
0C72
TRGCON3
0C74
Bit 0
All
Resets
XPRES
IUE
0000
SWAP
OSYNC
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
DTCP
—
MTBS
CAM
CLDAT<1:0>
FLTDAT<1:0>
FLTSRC<4:0>
PHASE3
TRIG3
Bit 6
OVRENH
PDC3
FLTPOL
FLTMOD<1:0>
—
TRGDIV<3:0>
0C7A
PHR
PHF
PLR
PLF
LEBDLY3
0C7C
—
—
—
—
0C7E
—
—
—
—
—
FLTLEBEN CLLEBEN
0000
DTR3<13:0>
0000
ALTDTR3<13:0>
0000
0000
—
—
—
—
—
—
—
—
TRGSTRT<5:0>
BCH
BCL
BPHH
BPHL
0000
BPLH
BPLL
LEB<11:0>
BLANKSEL<3:0>
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
00F8
0000
TRGCMP<15:0>
LEBCON3
Legend:
Bit 0
Bit 5
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-15:
AUXCON3
Bit 6
TRGCMP<15:0>
LEBCON2
Legend:
PMOD<1:0>
Bit 9
—
—
0000
0000
CHOPSEL<3:0>
CHOPHEN CHOPLEN
0000
DS70657E-page 79
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-14:
File Name Addr.
QEI1 REGISTER MAP FOR dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY
Bit 15
Bit 14
Bit 13
QEIEN
—
QEISIDL
QEI1CON
01C0
QEI1IOC
01C2 QCAPEN FLTREN
QEI1STAT
01C4
—
—
Bit 12
Bit 11
Bit 10
Bit 9
PIMOD<2:0>
QFDIV<2:0>
Bit 8
Bit 7
IMV<1:0>
OUTFNC<1:0>
SWPAB
Bit 6
—
PCIIRQ
Bit 4
INTDIV<2:0>
HOMPOL IDXPOL
PCHEQIRQ PCHEQIEN PCLEQIRQ PCLEQIEN POSOVIRQ POSOVIEN
Bit 5
QEBPOL
Bit 3
Bit 2
CNTPOL GATEN
QEAPOL
HOME
INDEX
Bit 1
Bit 0
CCM<1:0>
QEB
PCIIEN VELOVIRQ VELOVIEN HOMIRQ HOMIEN IDXIRQ
All
Resets
0000
QEA
000x
IDXIEN
0000
POS1CNTL 01C6
POSCNT<15:0>
0000
POS1CNTH 01C8
POSCNT<31:16>
0000
POS1HLD
01CA
POSHLD<15:0>
0000
VEL1CNT
01CC
VELCNT<15:0>
0000
INT1TMRL
01CE
INTTMR<15:0>
0000
INT1TMRH
01D0
INTTMR<31:16>
0000
INT1HLDL
01D2
INTHLD<15:0>
0000
INT1HLDH
01D4
INTHLD<31:16>
0000
INDX1CNTL 01D6
INDXCNT<15:0>
0000
INDX1CNTH 01D8
INDXCNT<31:16>
0000
01DA
INDXHLD<15:0>
0000
QEI1GECL
01DC
QEIGEC<15:0>
0000
QEI1ICL
01DC
QEIIC<15:0>
0000
INDX1HLD
Preliminary
QEI1GECH 01DE
QEIGEC<31:16>
0000
QEI1ICH
01DE
QEIIC<31:16>
0000
QEI1LECL
01E0
QEILEC<15:0>
0000
QEI1LECH
01E2
QEILEC<31:16>
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 80
TABLE 4-16:
File Name Addr.
I2C1 and I2C2 REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
I2C1RCV
0200
—
—
—
—
—
—
—
—
Receive Register
I2C1TRN
0202
—
—
—
—
—
—
—
—
Transmit Register
I2C1BRG
0204
—
—
—
—
—
—
—
I2C1CON
0206
I2CEN
—
I2CSIDL
SCLREL
IPMIEN
A10M
DISSLW
SMEN
GCEN
STREN
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
1000
I2C1STAT
0208 ACKSTAT TRSTAT
—
—
—
BCL
GCSTAT
ADD10
IWCOL
I2COV
D_A
P
S
R_W
RBF
TBF
0000
0000
00FF
Baud Rate Generator
0000
I2C1ADD
020A
—
—
—
—
—
—
Address Register
I2C1MSK
020C
—
—
—
—
—
—
Address Mask
I2C2RCV
0210
—
—
—
—
—
—
—
—
I2C2TRN
0212
—
—
—
—
—
—
—
—
I2C2BRG
0214
—
—
—
—
—
—
—
I2C2CON
0216
I2CEN
—
I2CSIDL
SCLREL
IPMIEN
A10M
DISSLW
SMEN
GCEN
STREN
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
1000
I2C2STAT
0218 ACKSTAT TRSTAT
—
—
—
BCL
GCSTAT
ADD10
IWCOL
I2COV
D_A
P
S
R_W
RBF
TBF
0000
I2C2ADD
021A
—
—
—
—
—
—
Address Register
0000
I2C2MSK
021C
—
—
—
—
—
—
Address Mask
0000
Preliminary
Legend:
0000
0000
Receive Register
0000
Transmit Register
00FF
Baud Rate Generator
0000
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-18:
UART1 and UART2 REGISTER MAP
SFR
Name
Addr.
U1MODE
0220
UARTEN
U1STA
0222
UTXISEL1
U1TXREG
0224
—
U1RXREG 0226
—
Bit 15
Bit 14
Bit 11
Bit 10
Bit 9
Bit 8
WAKE
LPBACK
Bit 4
Bit 3
ABAUD
URXINV
BRGH
ADDEN
RIDLE
PERR
Bit 2
Bit 1
STSEL
0000
0110
USIDL
IREN
RTSMD
—
UTXISEL0
—
UTXBRK
UTXEN
UTXBF
—
—
—
—
—
—
Transmit Register
xxxx
—
—
—
—
—
—
Receive Register
0000
URXISEL<1:0>
Bit 5
URXDA
—
UTXINV
TRMT
Bit 6
All
Resets
Bit 12
UEN<1:0>
Bit 7
Bit 0
Bit 13
PDSEL<1:0>
FERR
OERR
U1BRG
0228
U2MODE
0230
UARTEN
—
USIDL
IREN
RTSMD
—
U2STA
0232
UTXISEL1
UTXINV
UTXISEL0
—
UTXBRK
UTXEN
UTXBF
U2TXREG
0234
—
—
—
—
—
—
—
Transmit Register
xxxx
U2RXREG 0236
—
—
—
—
—
—
—
Receive Register
0000
U2BRG
Legend:
0238
Baud Rate Generator Prescaler
UEN<1:0>
TRMT
WAKE
LPBACK
URXISEL<1:0>
Baud Rate Generator Prescaler
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
ABAUD
URXINV
BRGH
ADDEN
RIDLE
PERR
PDSEL<1:0>
FERR
OERR
STSEL
0000
URXDA
0110
0000
DS70657E-page 81
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-17:
SPI1 and SPI2 REGISTER MAP
SFR Name Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
SPI1STAT
0240
SPIEN
—
SPISIDL
—
—
SPIBEC<2:0>
SPI1CON1
0242
—
—
—
DISSCK DISSDO MODE16
SMP
CKE
SSEN
CKP
MSTEN
SPI1CON2
0244
FRMEN
SPIFSD
FRMPOL
—
—
—
—
—
SPI1BUF
0248
SPI2STAT
0260
SPIEN
—
SPISIDL
SPI2CON1
0262
—
—
—
SPI2CON2
0264
FRMEN
SPIFSD
FRMPOL
SPI2BUF
0268
Legend:
—
—
Bit 10
—
Bit 9
Bit 8
Bit 7
SRMPT
Bit 6
Bit 5
Bit 4
SPIROV SRXMPT
Bit 3
Bit 2
SISEL<2:0>
SPRE<2:0>
—
—
—
Bit 1
Bit 0
SPITBF
SPIRBF
PPRE<1:0>
FRMDLY SPIBEN
0000
0000
—
SPIBEC<2:0>
DISSCK DISSDO MODE16
SMP
CKE
SSEN
CKP
MSTEN
—
—
—
—
—
—
—
—
SRMPT
SPIROV SRXMPT
SPI2 Transmit and Receive Buffer Register
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
0000
SPI1 Transmit and Receive Buffer Register
—
All
Resets
SISEL<2:0>
SPITBF
SPRE<2:0>
—
—
—
SPIRBF
0000
PPRE<1:0>
0000
FRMDLY SPIBEN
0000
0000
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 82
TABLE 4-19:
ADC1 REGISTER MAP
Preliminary
Addr.
ADC1BUF0
0300
ADC1 Data Buffer 0
xxxx
ADC1BUF1
0302
ADC1 Data Buffer 1
xxxx
ADC1BUF2
0304
ADC1 Data Buffer 2
xxxx
ADC1BUF3
0306
ADC1 Data Buffer 3
xxxx
ADC1BUF4
0308
ADC1 Data Buffer 4
xxxx
ADC1BUF5
030A
ADC1 Data Buffer 5
xxxx
ADC1BUF6
030C
ADC1 Data Buffer 6
xxxx
ADC1BUF7
030E
ADC1 Data Buffer 7
xxxx
ADC1BUF8
0310
ADC1 Data Buffer 8
xxxx
ADC1BUF9
0312
ADC1 Data Buffer 9
xxxx
ADC1BUFA
0314
ADC1 Data Buffer 10
xxxx
ADC1BUFB
0316
ADC1 Data Buffer 11
xxxx
ADC1BUFC
0318
ADC1 Data Buffer 12
xxxx
ADC1BUFD
031A
ADC1 Data Buffer 13
xxxx
ADC1BUFE
031C
ADC1 Data Buffer 14
xxxx
ADC1BUFF
031E
ADC1 Data Buffer 15
AD1CON1
0320
AD1CON2
0322
AD1CON3
0324
AD1CHS123 0326
Bit 15
ADON
Bit 14
—
Bit 13
ADSIDL
VCFG<2:0>
ADRC
—
—
—
—
—
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
ADDMABM
—
AD12B
FORM<1:0>
—
—
CSCNA
CHPS<1:0>
Bit 7
Bit 6
Bit 5
—
Bit 3
SSRCG
BUFS
SIMSAM
Bit 1
ASAM
SMPI<4:0>
Bit 0
SAMP
DONE
0000
BUFM
ALTS
0000
ADCS<7:0>
CH123NB<1:0>
CH123SB
—
—
CH0NA
—
—
CSS24
—
—
—
—
—
—
CSS2
CH0SB<4:0>
—
—
0000
—
AD1CHS0
0328
CH0NB
—
—
AD1CSSH
032E
CSS31
CSS30
—
—
—
CSS26
CSS25
AD1CSSL
0330
CSS15
CSS14
CSS13
CSS12
CSS11
CSS10
CSS9
CSS8
CSS7
CSS6
CSS5
CSS4
CSS3
AD1CON4
0332
—
—
—
—
—
—
—
ADDMAEN
—
—
—
—
—
Legend:
Bit 2
xxxx
SSRC<2:0>
SAMC<4:0>
—
Bit 4
All
Resets
File Name
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
CH123NA<1:0>
CH123SA
0000
—
—
0000
CSS1
CSS0
0000
CH0SA<4:0>
0000
DMABL<2:0>
0000
DS70657E-page 83
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-20:
File Name
ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 0 OR 1 FOR dsPIC33EPXXXMC/GP50X DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
C1CTRL1
0400
—
—
CSIDL
ABAT
CANCKS
C1CTRL2
0402
—
—
—
—
—
C1VEC
0404
—
—
—
0406
C1FIFO
0408
—
—
C1INTF
040A
—
—
TXBO
C1INTE
040C
—
—
—
C1EC
040E
C1CFG1
0410
C1CFG2
0412
C1FEN1
0414
DMABS<2:0>
Bit 9
Bit 8
Bit 7
—
—
REQOP<2:0>
—
—
—
—
RXBP
TXWAR
—
—
—
Bit 5
—
—
—
—
—
—
WAKFIL
—
—
—
Bit 3
—
CANCAP
—
—
RXWAR EWARN
—
—
Bit 2
Bit 1
Bit 0
All
Resets
—
—
WIN
0480
DNCNT<4:0>
0000
ICODE<6:0>
—
—
—
—
—
IVRIF
WAKIF
ERRIF
IVRIE
WAKIE
ERRIE
0040
FSA<4:0>
0000
FNRB<5:0>
TERRCNT<7:0>
—
Bit 4
—
FBP<5:0>
TXBP
Bit 6
OPMODE<2:0>
—
FILHIT<4:0>
—
C1FCTRL
Bit 10
0000
—
FIFOIF
RBOVIF
RBIF
TBIF
0000
—
FIFOIE
RBOVIE
RBIE
TBIE
0000
RERRCNT<7:0>
—
—
—
SEG2PH<2:0>
FLTEN15 FLTEN14 FLTEN13 FLTEN12 FLTEN11 FLTEN10 FLTEN9
FLTEN8
SJW<1:0>
SEG2PHTS
FLTEN7
0000
BRP<5:0>
SAM
SEG1PH<2:0>
FLTEN6 FLTEN5 FLTEN4
0000
PRSEG<2:0>
FLTEN3
FLTEN2
FLTEN1
0000
FLTEN0
FFFF
C1FMSKSEL1 0418
F7MSK<1:0>
F6MSK<1:0>
F5MSK<1:0>
F4MSK<1:0>
F3MSK<1:0>
F2MSK<1:0>
F1MSK<1:0>
F0MSK<1:0>
0000
C1FMSKSEL2 041A
F15MSK<1:0>
F14MSK<1:0>
F13MSK<1:0>
F12MSK<1:0>
F11MSK<1:0>
F10MSK<1:0>
F9MSK<1:0>
F8MSK<1:0>
0000
Legend:
— = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Preliminary
TABLE 4-22:
File Name
Addr
ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 0 FOR dsPIC33EPXXXMC/GP50X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
0400041E
Bit 9
Bit 8
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
RXFUL6
RXFUL5
RXFUL4
RXFUL3
RXFUL2
RXFUL1
RXFUL0
0000
Bit 7
See definition when WIN = x
C1RXFUL1
0420 RXFUL15 RXFUL14 RXFUL13 RXFUL12 RXFUL11 RXFUL10 RXFUL9
C1RXFUL2
0422 RXFUL31 RXFUL30 RXFUL29 RXFUL28 RXFUL27 RXFUL26 RXFUL25 RXFUL24 RXFUL23 RXFUL22 RXFUL21 RXFUL20 RXFUL19 RXFUL18 RXFUL17 RXFUL16
RXFUL8
0000
C1RXOVF1
0428 RXOVF15 RXOVF14 RXOVF13 RXOVF12 RXOVF11 RXOVF10 RXOVF9
RXOVF3 RXOVF2 RXOVF1 RXOVF0
0000
C1RXOVF2
042A RXOVF31 RXOVF30 RXOVF29 RXOVF28 RXOVF27 RXOVF26 RXOVF25 RXOVF24 RXOVF23 RXOVF22 RXOVF21 RXOVF20 RXOVF19 RXOVF18 RXOVF17 RXOVF16
0000
RXOVF8
RXFUL7
RXOVF7
RXOVF6
RXOVF5
RXOVF4
© 2011-2012 Microchip Technology Inc.
C1TR01CON 0430
TXEN1
TXABT1 TXLARB1 TXERR1
TXREQ1
RTREN1
TX1PRI<1:0>
TXEN0
TXABAT0 TXLARB0 TXERR0
TXREQ0 RTREN0
TX0PRI<1:0>
0000
C1TR23CON 0432
TXEN3
TXABT3 TXLARB3 TXERR3
TXREQ3
RTREN3
TX3PRI<1:0>
TXEN2
TXABAT2 TXLARB2 TXERR2
TXREQ2 RTREN2
TX2PRI<1:0>
0000
C1TR45CON 0434
TXEN5
TXABT5 TXLARB5 TXERR5
TXREQ5
RTREN5
TX5PRI<1:0>
TXEN4
TXABAT4 TXLARB4 TXERR4
TXREQ4 RTREN4
TX4PRI<1:0>
0000
C1TR67CON 0436
TXEN7
TXABT7 TXLARB7 TXERR7
TXREQ7
RTREN7
TX7PRI<1:0>
TXEN6
TXABAT6 TXLARB6 TXERR6
TXREQ6 RTREN6
TX6PRI<1:0>
xxxx
C1RXD
0440
Received Data Word
xxxx
C1TXD
0442
Transmit Data Word
xxxx
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 84
TABLE 4-21:
File Name
Addr
ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 1 FOR dsPIC33EPXXXMC/GP50X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
0400041E
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
See definition when WIN = x
Preliminary
DS70657E-page 85
C1BUFPNT1
0420
F3BP<3:0>
F2BP<3:0>
F1BP<3:0>
F0BP<3:0>
0000
C1BUFPNT2
0422
F7BP<3:0>
F6BP<3:0>
F5BP<3:0>
F4BP<3:0>
0000
C1BUFPNT3
0424
F11BP<3:0>
F10BP<3:0>
F9BP<3:0>
F8BP<3:0>
0000
C1BUFPNT4
0426
F15BP<3:0>
F14BP<3:0>
F13BP<3:0>
F12BP<3:0>
0000
C1RXM0SID
0430
SID<10:3>
—
EID<17:16>
xxxx
C1RXM0EID
0432
EID<15:8>
C1RXM1SID
0434
SID<10:3>
—
EID<17:16>
C1RXM1EID
0436
EID<15:8>
C1RXM2SID
0438
SID<10:3>
—
EID<17:16>
C1RXM2EID
043A
EID<15:8>
C1RXF0SID
0440
SID<10:3>
—
EID<17:16>
C1RXF0EID
0442
EID<15:8>
C1RXF1SID
0444
SID<10:3>
—
EID<17:16>
C1RXF1EID
0446
EID<15:8>
C1RXF2SID
0448
SID<10:3>
—
EID<17:16>
C1RXF2EID
044A
EID<15:8>
C1RXF3SID
044C
SID<10:3>
—
EID<17:16>
C1RXF3EID
044E
EID<15:8>
C1RXF4SID
0450
SID<10:3>
—
EID<17:16>
C1RXF4EID
0452
EID<15:8>
C1RXF5SID
0454
SID<10:3>
—
EID<17:16>
C1RXF5EID
0456
EID<15:8>
C1RXF6SID
0458
SID<10:3>
—
EID<17:16>
C1RXF6EID
045A
EID<15:8>
C1RXF7SID
045C
SID<10:3>
—
EID<17:16>
C1RXF7EID
045E
EID<15:8>
C1RXF8SID
0460
SID<10:3>
—
EID<17:16>
C1RXF8EID
0462
EID<15:8>
C1RXF9SID
0464
SID<10:3>
—
EID<17:16>
C1RXF9EID
0466
EID<15:8>
C1RXF10SID
0468
SID<10:3>
—
EID<17:16>
C1RXF10EID
046A
EID<15:8>
C1RXF11SID
046C
SID<10:3>
—
EID<17:16>
C1RXF11EID
046E
EID<15:8>
C1RXF12SID
0470
SID<10:3>
—
EID<17:16>
C1RXF12EID
0472
EID<15:8>
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
SID<2:0>
—
MIDE
EID<7:0>
SID<2:0>
—
MIDE
xxxx
EID<7:0>
SID<2:0>
—
MIDE
xxxx
EID<7:0>
SID<2:0>
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
—
EXIDE
EID<7:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
xxxx
xxxx
xxxx
xxxx
xxxx
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-23:
File Name
Addr
ECAN1 REGISTER MAP WHEN WIN (C1CTRL<0>) = 1 FOR dsPIC33EPXXXMC/GP50X DEVICES ONLY (CONTINUED)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
C1RXF13SID
0474
SID<10:3>
C1RXF13EID
0476
EID<15:8>
C1RXF14SID
0478
SID<10:3>
C1RXF14EID
047A
EID<15:8>
C1RXF15SID
047C
SID<10:3>
C1RXF15EID
047E
EID<15:8>
Legend:
Bit 10
Bit 9
Bit 8
Bit 7
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Bit 6
SID<2:0>
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
—
EXIDE
—
EID<17:16>
—
EID<17:16>
—
EID<17:16>
EID<7:0>
SID<2:0>
—
EXIDE
—
EXIDE
EID<7:0>
xxxx
xxxx
EID<7:0>
SID<2:0>
All
Resets
xxxx
xxxx
xxxx
xxxx
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 86
TABLE 4-23:
File Name
CRC REGISTER MAP
Bit 12
Bit 11
Bit 10
CRCEN
—
CSIDL
VWORD<4:0>
—
—
—
DWIDTH<4:0>
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
LENDIAN
—
—
0000
0642
CRCXORL
0644
CRCXORH
0646
X<23:16>
0000
CRCDATL
0648
CRC Data Input Low Word
0000
CRCDATH
064A
CRC Data Input High Word
0000
CRCWDATL
064C
CRC Result Low Word
0000
CRCWDATH
064E
CRC Result High Word
0000
—
CRCGO
—
0640
—
Bit 3
All
Resets
CRCCON2
CRCFUL CRCMPT CRCISEL
Bit 4
Bit 0
CRCCON1
—
PLEN<4:0>
0000
X<15:1>
—
0000
— = unimplemented, read as ‘0’. Shaded bits are not used in the operation of the programmable CRC module.
TABLE 4-25:
Preliminary
File
Name
Bit 13
Bit 1
Bit 15
Legend:
Bit 14
Bit 2
Addr.
PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXXGP/MC202/502 AND PIC24EPXXXGP/MC202
DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
RPOR0
0680
—
—
RP35R<5:0>
—
—
RP20R<5:0>
0000
RPOR1
0682
—
—
RP37R<5:0>
—
—
RP36R<5:0>
0000
RPOR2
0684
—
—
RP39R<5:0>
—
—
RP38R<5:0>
0000
RPOR3
0686
—
—
RP41R<5:0>
—
—
RP40R<5:0>
0000
RPOR4
0688
—
—
RP43R<5:0>
—
—
RP42R<5:0>
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-26:
PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXXGP/MC203/503 AND PIC24EPXXXGP/MC203
DEVICES ONLY
File
Name
Addr.
Bit 15
Bit 14
RPOR0
0680
—
—
RPOR1
0682
—
—
RPOR2
0684
—
RPOR3
0686
RPOR4
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
DS70657E-page 87
Bit 6
RP35R<5:0>
—
—
RP20R<5:0>
0000
RP37R<5:0>
—
—
RP36R<5:0>
0000
—
RP39R<5:0>
—
—
RP38R<5:0>
0000
—
—
RP41R<5:0>
—
—
RP40R<5:0>
0000
0688
—
—
RP43R<5:0>
—
—
RP42R<5:0>
RPOR5
068A
—
—
—
—
—
—
—
—
—
—
RPOR6
068C
—
—
—
—
—
—
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Bit 5
—
Bit 4
—
Bit 3
—
Bit 2
—
RP56R<5:0>
Bit 1
Bit 0
All
Resets
Bit 7
Legend:
Bit 13
0000
—
—
0000
0000
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-24:
File
Name
PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXXGP/MC204/504 AND PIC24EPXXXGP/MC204
DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
RPOR0
0680
—
—
RP35R<5:0>
—
—
RP20R<5:0>
0000
RPOR1
0682
—
—
RP37R<5:0>
—
—
RP36R<5:0>
0000
RPOR2
0684
—
—
RP39R<5:0>
—
—
RP38R<5:0>
0000
RPOR3
0686
—
—
RP41R<5:0>
—
—
RP40R<5:0>
0000
RPOR4
0688
—
—
RP43R<5:0>
—
—
RP42R<5:0>
0000
RPOR5
068A
—
—
RP55R<5:0>
—
—
RP54R<5:0>
0000
RPOR6
068C
—
—
RP57R<5:0>
—
—
RP56R<5:0>
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-28:
PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33EPXXXGP/MC206/506 AND PIC24EPXXXGP/MC206
DEVICES ONLY
Preliminary
File
Name
Addr.
Bit 15
Bit 14
RPOR0
0680
—
—
RPOR1
0682
—
—
RPOR2
0684
—
RPOR3
0686
RPOR4
Bit 6
RP35R<5:0>
—
—
RP20R<5:0>
0000
RP37R<5:0>
—
—
RP36R<5:0>
0000
—
RP39R<5:0>
—
—
RP38R<5:0>
0000
—
—
RP41R<5:0>
—
—
RP40R<5:0>
0000
0688
—
—
RP43R<5:0>
—
—
RP42R<5:0>
0000
RPOR5
068A
—
—
RP55R<5:0>
—
—
RP54R<5:0>
0000
RPOR6
068C
—
—
RP57R<5:0>
—
—
RP56R<5:0>
RPOR7
068E
—
—
RP97R<5:0>
—
—
—
—
—
—
—
—
RPOR8
0690
—
—
RP118R<5:0>
—
—
—
—
—
—
—
—
RPOR9
0692
—
—
—
—
—
Bit 12
—
Bit 11
—
Bit 10
—
Bit 9
—
Bit 8
—
© 2011-2012 Microchip Technology Inc.
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Bit 5
Bit 4
Bit 3
Bit 2
RP120R<5:0>
Bit 1
Bit 0
All
Resets
Bit 7
Legend:
Bit 13
0000
0000
0000
0000
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 88
TABLE 4-27:
PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR PIC24EPXXXMC20X DEVICES ONLY
File
Name
Addr.
Bit 15
RPINR0
06A0
—
RPINR1
06A2
RPINR3
Bit 14
Bit 13
Bit 12
—
—
—
—
06A6
—
—
—
—
RPINR7
06AE
—
RPINR8
06B0
—
RPINR11 06B6
—
RPINR12 06B8
—
RPINR14 06BC
—
0000
Preliminary
INT2R<6:0>
0000
—
—
—
—
—
T2CKR<6:0>
0000
IC2R<6:0>
—
IC1R<6:0>
0000
IC4R<6:0>
—
IC3R<6:0>
0000
—
OCFAR<6:0>
0000
FLT2R<6:0>
—
FLT1R<6:0>
0000
—
QEB1R<6:0>
—
QEA1R<6:0>
0000
RPINR15 06BE
—
HOME1R<6:0>
—
INDX1R<6:0>
0000
RPINR18 06C4
—
—
—
—
—
—
—
—
—
U1RXR<6:0>
0000
RPINR19 06C6
—
—
—
—
—
—
—
—
—
U2RXR<6:0>
0000
RPINR22 06CC
—
—
SDI2R<6:0>
0000
RPINR23 06CE
—
—
—
—
—
—
—
—
—
SS2R<6:0>
RPINR26 06D4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
RPINR37 06EA
—
SYNCI1R<6:0>
—
—
—
—
—
—
—
—
0000
RPINR38 06EC
—
DTCMP1R<6:0>
—
—
—
—
—
—
—
—
0000
RPINR39 06EE
—
DTCMP3R<6:0>
—
SCK2INR<6:0>
0000
DTCMP2R<6:0>
0000
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-30:
PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR PIC24EPXXXGP20X DEVICES ONLY
File
Name
Addr.
Bit 15
RPINR0
06A0
—
RPINR1
06A2
RPINR3
DS70657E-page 89
Bit 14
Bit 13
Bit 12
—
—
—
—
06A6
—
—
—
—
RPINR7
06AE
—
RPINR8
06B0
—
RPINR11 06B6
—
—
—
—
—
—
—
RPINR18 06C4
—
—
—
—
—
—
RPINR19 06C6
—
—
—
—
—
—
RPINR22 06CC
—
RPINR23 06CE
—
Legend:
—
—
—
—
—
—
—
—
—
—
—
—
—
—
All
Resets
—
—
Bit 4
Bit 0
—
—
Bit 5
Bit 1
Bit 8
—
Bit 6
Bit 2
Bit 9
INT1R<6:0>
Bit 7
Bit 3
Bit 10
Legend:
Bit 11
Bit 11
—
—
—
—
—
—
—
—
0000
—
—
INT2R<6:0>
0000
—
—
—
—
—
T2CKR<6:0>
0000
IC2R<6:0>
—
IC1R<6:0>
0000
IC4R<6:0>
—
IC3R<6:0>
0000
—
—
OCFAR<6:0>
0000
—
—
—
U1RXR<6:0>
0000
—
—
—
U2RXR<6:0>
0000
—
SDI2R<6:0>
0000
—
SS2R<6:0>
0000
—
—
—
—
—
—
All
Resets
—
—
Bit 4
Bit 0
—
—
Bit 5
Bit 1
Bit 8
SCK2INR<6:0>
Bit 6
Bit 2
Bit 9
INT1R<6:0>
Bit 7
Bit 3
Bit 10
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-29:
File
Name
PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXGP50X DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 6
Bit 5
Bit 4
—
—
—
—
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
—
—
0000
RPINR0
06A0
—
RPINR1
06A2
—
—
—
—
—
—
—
—
—
INT2R<6:0>
0000
RPINR3
06A6
—
—
—
—
—
—
—
—
—
T2CKR<6:0>
0000
RPINR7
06AE
—
IC2R<6:0>
—
IC1R<6:0>
0000
RPINR8
06B0
—
IC4R<6:0>
—
IC3R<6:0>
0000
RPINR11 06B6
—
—
—
—
—
—
—
—
—
OCFAR<6:0>
0000
RPINR18 06C4
—
—
—
—
—
—
—
—
—
U1RXR<6:0>
0000
RPINR19 06C6
—
—
—
—
—
—
—
—
—
U2RXR<6:0>
0000
RPINR22 06CC
—
—
SDI2R<6:0>
0000
RPINR23 06CE
—
—
—
—
—
—
—
—
—
SS2R<6:0>
0000
RPINR26 06D4
—
—
—
—
—
—
—
—
—
C1RXR<6:0>
0000
Legend:
SCK2INR<6:0>
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-32:
Preliminary
File
Name
INT1R<6:0>
Bit 7
PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXMC50X DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 6
Bit 5
Bit 4
—
—
—
—
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
—
—
0000
© 2011-2012 Microchip Technology Inc.
RPINR0
06A0
—
RPINR1
06A2
—
—
—
—
—
—
—
—
—
INT2R<6:0>
0000
RPINR3
06A6
—
—
—
—
—
—
—
—
—
T2CKR<6:0>
0000
RPINR7
06AE
—
IC2R<6:0>
—
IC1R<6:0>
0000
RPINR8
06B0
—
IC4R<6:0>
—
IC3R<6:0>
0000
RPINR11 06B6
—
—
OCFAR<6:0>
0000
RPINR12 06B8
—
FLT2R<6:0>
—
FLT1R<6:0>
0000
RPINR14 06BC
—
QEB1R<6:0>
—
QEA1R<6:0>
0000
RPINR15 06BE
—
HOME1R<6:0>
—
INDX1R<6:0>
0000
RPINR18 06C4
—
—
—
—
—
—
—
—
—
U1RXR<6:0>
0000
RPINR19 06C6
—
—
—
—
—
—
—
—
—
U2RXR<6:0>
0000
RPINR22 06CC
—
—
SDI2R<6:0>
0000
RPINR23 06CE
—
—
—
—
—
—
—
—
—
SS2R<6:0>
0000
RPINR26 06D4
—
—
—
—
—
—
—
—
—
C1RXR<6:0>
RPINR37 06EA
—
SYNCI1R<6:0>
—
—
—
—
RPINR38 06EC
—
DTCMP1R<6:0>
—
—
—
—
RPINR39 06EE
—
DTCMP3R<6:0>
—
Legend:
INT1R<6:0>
Bit 7
—
—
—
—
—
—
—
SCK2INR<6:0>
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
—
—
—
—
0000
—
—
—
—
0000
DTCMP2R<6:0>
0000
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 90
TABLE 4-31:
File
Name
PERIPHERAL PIN SELECT INPUT REGISTER MAP FOR dsPIC33EPXXXMC20X DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 6
Bit 5
Bit 4
—
—
—
—
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
—
—
0000
Preliminary
RPINR0
06A0
—
RPINR1
06A2
—
—
—
—
—
—
—
—
—
INT2R<6:0>
0000
RPINR3
06A6
—
—
—
—
—
—
—
—
—
T2CKR<6:0>
0000
RPINR7
06AE
—
IC2R<6:0>
—
IC1R<6:0>
0000
RPINR8
06B0
—
IC4R<6:0>
—
IC3R<6:0>
0000
RPINR11 06B6
—
—
OCFAR<6:0>
0000
RPINR12 06B8
—
FLT2R<6:0>
—
FLT1R<6:0>
0000
RPINR14 06BC
—
QEB1R<6:0>
—
QEA1R<6:0>
0000
RPINR15 06BE
—
HOME1R<6:0>
—
INDX1R<6:0>
0000
RPINR18 06C4
—
—
—
—
—
—
—
—
—
U1RXR<6:0>
0000
RPINR19 06C6
—
—
—
—
—
—
—
—
—
U2RXR<6:0>
0000
RPINR22 06CC
—
—
SDI2R<6:0>
0000
RPINR23 06CE
—
—
SS2R<6:0>
RPINR37 06EA
—
SYNCI1R<6:0>
—
—
—
—
RPINR38 06EC
—
DTCMP1R<6:0>
—
—
—
—
RPINR39 06EE
—
DTCMP3R<6:0>
—
Legend:
INT1R<6:0>
Bit 7
—
—
—
—
—
—
—
SCK2INR<6:0>
—
—
—
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
0000
—
—
—
—
0000
—
—
—
—
0000
DTCMP2R<6:0>
0000
DS70657E-page 91
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-33:
File Name
NVM REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
NVMCON
0728
WR
WREN
WRERR
NVMSIDL
—
—
—
NVMADR
072A
NVMADRU
072C
—
—
—
—
—
—
—
—
NVMADR<23:16>
0000
NVMKEY
072E
—
—
—
—
—
—
—
—
NVMKEY<7:0>
0000
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
—
—
—
—
—
Bit 2
Bit 1
Bit 0
NVMOP<3:0>
0000
NVMADR<15:0>
0000
SYSTEM CONTROL REGISTER MAP
Addr.
Bit 15
Bit 14
RCON
0740
TRAPR
IOPUWR
OSCCON
0742
—
Bit 13
Bit 12
Bit 11
Bit 10
—
—
VREGSF
—
COSC<2:0>
—
Bit 8
CM
VREGS
NOSC<2:0>
DOZEN
Bit 7
Bit 6
Bit 5
Bit 4
EXTR
SWR
SWDTEN
WDTO
CLKLOCK
IOLOCK
LOCK
—
Preliminary
CLKDIV
0744
ROI
0746
—
—
—
—
—
—
—
OSCTUN
0748
—
—
—
—
—
—
—
Legend:
Note 1:
2:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
RCON register reset values dependent on type of reset.
OSCCON register reset values dependent on configuration fuses, and by type of reset.
TABLE 4-36:
DOZE<2:0>
Bit 9
PLLFBD
File Name
Bit 3
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-35:
File Name
Bit 8
All
Resets
Addr.
FRCDIV<2:0>
PLLPOST<1:0>
Bit 3
Bit 2
Bit 1
SLEEP IDLE
BOR
CF
—
—
—
Bit 0
All
Resets
POR
Note 1
OSWEN Note 2
PLLPRE<4:0>
0030
PLLDIV<8:0>
—
—
0030
—
TUN<5:0>
0000
REFERENCE CLOCK REGISTER MAP
© 2011-2012 Microchip Technology Inc.
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
REFOCON
074E
ROON
—
ROSSLP
ROSEL
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
—
—
—
—
0000
RODIV<3:0>
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 92
TABLE 4-34:
File
Addr.
Name
PMD REGISTER MAP FOR PIC24EPXXXGP20X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
0000
PMD1
0760
T5MD
T4MD
T3MD
T2MD
T1MD
—
—
—
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
—
—
AD1MD
PMD2
0762
—
—
—
—
IC4MD
IC3MD
IC2MD
IC1MD
—
—
—
—
OC4MD
OC3MD
OC2MD
OC1MD
0000
PMD3
0764
—
—
—
—
—
CMPMD
—
—
CRCMD
—
—
—
—
—
I2C2MD
—
0000
PMD4
0766
—
—
—
—
—
—
—
—
—
—
—
—
PMD6
076A
—
—
—
—
—
—
—
—
—
—
—
—
REFOMD CTMUMD
—
0000
—
—
—
0000
PTGMD
—
—
—
0000
Bit 2
Bit 1
Bit 0
All
Resets
DMA0MD
PMD7
—
076C
—
—
—
—
—
—
—
—
—
—
DMA1MD
DMA2MD
DMA3MD
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-38:
Preliminary
—
—
File
Addr.
Name
PMD REGISTER MAP FOR PIC24EPXXXMC20X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
PMD1
0760
T5MD
T4MD
T3MD
T2MD
T1MD
QEI1MD
PWMMD
—
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
—
—
AD1MD
0000
PMD2
0762
—
—
—
—
IC4MD
IC3MD
IC2MD
IC1MD
—
—
—
—
OC4MD
OC3MD
OC2MD
OC1MD
0000
PMD3
0764
—
—
—
—
—
CMPMD
—
—
CRCMD
—
—
—
—
—
I2C2MD
—
0000
PMD4
0766
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
PMD6
076A
—
—
—
—
—
PWM3MD
—
—
—
—
PWM2MD PWM1MD
REFOMD CTMUMD
—
—
—
—
0000
PTGMD
—
—
—
0000
DMA0MD
PMD7
076C
—
—
—
—
—
—
—
—
—
—
—
DMA1MD
DMA2MD
DMA3MD
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
DS70657E-page 93
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-37:
File
Addr.
Name
PMD REGISTER MAP FOR dsPIC33EPXXXGP50X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
0000
PMD1
0760
T5MD
T4MD
T3MD
T2MD
T1MD
—
—
—
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
—
C1MD
AD1MD
PMD2
0762
—
—
—
—
IC4MD
IC3MD
IC2MD
IC1MD
—
—
—
—
OC4MD
OC3MD
OC2MD
OC1MD
0000
PMD3
0764
—
—
—
—
—
CMPMD
—
—
CRCMD
—
—
—
—
—
I2C2MD
—
0000
PMD4
0766
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
PMD6
076A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
—
—
DMA0MD
DMA1MD
DMA2MD
DMA3MD
PTGMD
—
—
—
0000
Bit 2
Bit 1
Bit 0
All
Resets
PMD7
Legend:
076C
—
—
—
—
—
—
—
—
—
REFOMD CTMUMD
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-40:
File
Addr.
Name
PMD REGISTER MAP FOR dsPIC33EPXXXMC50X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Preliminary
PMD1
0760
T5MD
T4MD
T3MD
T2MD
T1MD
QEI1MD
PWMMD
—
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
—
C1MD
AD1MD
0000
PMD2
0762
—
—
—
—
IC4MD
IC3MD
IC2MD
IC1MD
—
—
—
—
OC4MD
OC3MD
OC2MD
OC1MD
0000
PMD3
0764
—
—
—
—
—
CMPMD
—
—
CRCMD
—
—
—
—
—
I2C2MD
—
0000
PMD4
0766
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
PMD6
076A
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
—
—
DMA0MD
DMA1MD
DMA2MD
DMA3MD
PTGMD
—
—
—
0000
Bit 2
Bit 1
Bit 0
All
Resets
PMD7
Legend:
076C
—
—
—
—
—
PWM3MD PWM2MD PWM1MD
—
—
—
—
REFOMD CTMUMD
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-41:
© 2011-2012 Microchip Technology Inc.
File
Addr.
Name
PMD REGISTER MAP FOR dsPIC33EPXXXMC20X DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
PMD1
0760
T5MD
T4MD
T3MD
T2MD
T1MD
QEI1MD
PWMMD
—
I2C1MD
U2MD
U1MD
SPI2MD
SPI1MD
—
—
AD1MD
0000
PMD2
0762
—
—
—
—
IC4MD
IC3MD
IC2MD
IC1MD
—
—
—
—
OC4MD
OC3MD
OC2MD
OC1MD
0000
PMD3
0764
—
—
—
—
—
CMPMD
—
—
CRCMD
—
—
—
—
—
I2C2MD
—
0000
PMD4
0766
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
PMD6
076A
—
—
—
—
—
PWM3MD
—
—
—
—
PWM2MD PWM1MD
REFOMD CTMUMD
—
—
—
—
0000
PTGMD
—
—
—
0000
DMA0MD
PMD7
076C
—
—
—
—
—
—
—
—
—
—
—
DMA1MD
DMA2MD
DMA3MD
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 94
TABLE 4-39:
File Name
OP AMP/COMPARATOR REGISTER MAP
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
C4OUT
C3OUT
C2OUT
C1OUT
0000
CMSTAT
0A80
PSIDL
—
—
—
C4EVT
C3EVT
C2EVT
C1EVT
—
—
—
—
CVRCON
0A82
—
CVR2OE
—
—
—
VREFSEL
—
—
CVREN
CVR1OE
CVRR
CVRSS
CM1CON
0A84
CON
COE
CPOL
—
—
OPMODE
CEVT
COUT
—
CREF
—
—
CM1MSKSRC 0A86
—
—
—
—
CM1MSKCON 0A88
HLMS
—
OCEN
OCNEN
OBEN
OBNEN
ACNEN
ABEN
ABNEN
EVPOL<1:0>
SELSRCC<3:0>
SELSRCB<3:0>
OAEN
OANEN
CM1FLTR
0A8A
—
—
—
—
—
—
—
—
CM2CON
0A8C
CON
COE
CPOL
—
—
OPMODE
CEVT
COUT
CM2MSKSRC 0A8E
—
—
—
—
CM2MSKCON 0A90
HLMS
—
OCEN
OCNEN
OBEN
OBNEN
NAGS
OANEN
0A92
—
—
—
—
—
—
—
—
CON
COE
CPOL
—
—
OPMODE
CEVT
COUT
CM3MSKSRC 0A96
—
—
—
—
CM3MSKCON 0A98
HLMS
—
OCEN
OCNEN
OBEN
OBNEN
CFLTREN
ACEN
—
—
ACNEN
ABEN
ABNEN
—
CFLTREN
—
—
OANEN
NAGS
Preliminary
0A9A
—
—
—
—
—
—
—
—
CON
COE
CPOL
—
—
—
CEVT
COUT
CM4MSKSRC 0A9E
—
—
—
—
CM4MSKCON 0AA0
HLMS
—
OCEN
OCNEN
OBEN
OBNEN
OAEN
OANEN
NAGS
—
—
—
—
—
—
—
—
—
PAGS
—
ACEN
ACNEN
ABEN
ABNEN
SELSRCA<3:0>
CFSEL<2:0>
EVPOL<1:0>
SELSRCC<3:0>
—
CFLTREN
—
—
ACNEN
ABEN
ABNEN
SELSRCB<3:0>
PAGS
ACEN
SELSRCA<3:0>
CFSEL<2:0>
CFLTREN
0000
0000
CCH<1:0>
AAEN
0000
0000
AANEN
CFDIV<2:0>
CREF
0000
0000
CCH<1:0>
AAEN
0000
0000
AANEN
CFDIV<2:0>
CREF
0000
0000
CCH<1:0>
AAEN
0000
0000
AANEN
SELSRCA<3:0>
SELSRCB<3:0>
OAEN
AAEN
CFDIV<2:0>
CREF
CFSEL<2:0>
SELSRCC<3:0>
0A9C
0000
0000
AANEN
CFDIV<2:0>
0000
0000
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-43:
Addr
CTMUCON1 033A
CTMUCON2 033C
Legend:
PAGS
—
CM4CON
CTMUICON
—
EVPOL<1:0>
CM3FLTR
File Name
CFSEL<2:0>
NAGS
0000
CCH<1:0>
SELSRCA<3:0>
SELSRCB<3:0>
OAEN
0A94
0AA2
ACEN
EVPOL<1:0>
SELSRCC<3:0>
CM3CON
Legend:
PAGS
—
CM2FLTR
CM4FLTR
CVR<3:0>
CTMU REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
CTMUEN
—
CTMUSIDL
TGEN
EDGEN EDGSEQEN
—
—
EDG1SEL<1:0>
EDG1MOD EDG1POL
033E
Bit 11
Bit 10
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
IDISSEN
CTTRIG
—
—
—
—
—
—
—
—
—
Bit 5
Bit 4
EDG2STAT EDG1STAT EDG2MOD EDG2POL
ITRIM<5:0>
—
IRNG<1:0>
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
—
—
—
—
0000
—
—
0000
—
—
0000
Bit 0
All
Resets
xxxx
EDG2SEL<1:0>
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-44:
DS70657E-page 95
Bit 9
JTAG INTERFACE REGISTER MAP
File Name
Addr
Bit 15
Bit 14
Bit 13
Bit 12
JDATAH
0FF0
—
—
—
—
JDATAL
0FF2
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
JDATAH<27:16>
JDATAL<15:0>
Bit 3
Bit 2
Bit 1
0000
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-42:
File Name
Addr.
DMAC REGISTER MAP
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
—
—
DMA0CON
0B00
CHEN
SIZE
DIR
HALF
NULLW
—
—
—
DMA0REQ
0B02
FORCE
—
—
—
—
—
—
—
DMA0STAL
0B04
DMA0STAH
0B06
DMA0STBL
0B08
DMA0STBH
0B0A
DMA0PAD
0B0C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
SIZE
DIR
HALF
NULLW
—
—
—
DMA1REQ
0B12
FORCE
—
—
—
—
—
—
—
DMA1STAL
0B14
DMA1STAH
0B16
DMA1STBL
0B18
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Preliminary
—
—
SIZE
DIR
HALF
NULLW
—
—
—
DMA2REQ
0B22
FORCE
—
—
—
—
—
—
—
DMA2STAL
0B24
DMA2STAH
0B26
DMA2STBL
0B28
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
MODE<1:0>
IRQSEL<7:0>
00FF
STA<23:16>
0000
0000
STB<23:16>
0000
0000
CNT<13:0>
—
—
0000
AMODE<1:0>
—
—
MODE<1:0>
IRQSEL<7:0>
© 2011-2012 Microchip Technology Inc.
—
—
SIZE
DIR
HALF
NULLW
—
—
—
DMA3REQ
0B32
FORCE
—
—
—
—
—
—
—
DMA3STAL
0B34
DMA3STAH
0B36
DMA3STBL
0B38
00FF
STA<23:16>
0000
0000
STB<23:16>
0000
0000
CNT<13:0>
—
—
0000
AMODE<1:0>
—
—
MODE<1:0>
IRQSEL<7:0>
—
—
—
—
—
—
0000
—
STA<23:16>
0000
STB<15:0>
—
—
—
—
—
—
—
0000
00FF
STA<15:0>
—
0000
0000
—
CHEN
0000
0000
PAD<15:0>
0B30
0B3A
0000
AMODE<1:0>
—
0B2E
0B3C
CNT<13:0>
—
—
STB<15:0>
DMA2CNT
DMA3PAD
0000
0000
STA<15:0>
DMA3CON
DMA3STBH
0000
STB<23:16>
—
CHEN
0000
0000
PAD<15:0>
0B20
0B2A
STA<23:16>
—
0B1E
All
Resets
00FF
STB<15:0>
DMA1CNT
0B2C
MODE<1:0>
STA<15:0>
DMA2CON
DMA2PAD
—
Bit 0
0000
—
CHEN
DMA2STBH
—
Bit 1
PAD<15:0>
0B10
0B1A
Bit 2
IRQSEL<7:0>
—
0B0E
0B1C
AMODE<1:0>
Bit 3
STB<15:0>
DMA0CNT
DMA1PAD
Bit 4
STA<15:0>
DMA1CON
DMA1STBH
Bit 5
0000
—
STB<23:16>
0000
PAD<15:0>
0000
DMA3CNT
0B3E
—
—
DMAPWC
0BF0
—
—
—
—
—
—
—
—
CNT<13:0>
—
—
—
—
PWCOL3 PWCOL2 PWCOL1 PWCOL0
0000
DMARQC
0BF2
—
—
—
—
—
—
—
—
—
—
—
—
RQCOL3 RQCOL2 RQCOL1 RQCOL0
0000
DMAPPS
0BF4
—
—
—
—
—
—
—
—
—
—
—
—
DMALCA
0BF6
—
—
—
—
—
—
—
—
—
—
—
—
DSADRL
0BF8
DSADRH
0BFA
Legend:
0000
PPST3
DSADR<15:0>
—
—
—
—
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
PPST2
PPST1
LSTCH<3:0>
PPST0
0000
000F
0000
DSADR<23:16>
0000
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 96
TABLE 4-45:
File
Name
PORTA REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISA
0E00
—
—
—
TRISA12
TRISA11
TRISA10
TRISA9
TRISA8
TRISA7
—
—
TRISA4
—
—
TRISA1
TRISA0
1F93
PORTA
0E02
—
—
—
RA12
RA11
RA10
RA9
RA8
RA7
—
—
RA4
—
—
RA1
RA0
0000
LATA
0E04
—
—
—
LATA12
LATA11
LATA10
LATA9
LATA8
LATA7
—
—
LATA4
—
—
LA1TA1
LA0TA0
0000
ODCA
0E06
—
—
—
ODCA12
ODCA11
ODCA10
ODCA9
ODCA8
ODCA7
—
—
ODCA4
—
—
ODCA1
ODCA0
0000
CNENA
0E08
—
—
—
CNIEA12
CNIEA11
CNIEA10
CNIEA9
CNIEA8
CNIEA7
—
—
CNIEA4
—
—
CNIEA1
CNIEA0
0000
CNPUA
0E0A
—
—
—
CNPUA12 CNPUA11 CNPUA10 CNPUA9 CNPUA8 CNPUA7
—
—
CNPUA4
—
—
CNPUA1 CNPUA0
0000
CNPDA
0E0C
—
—
—
CNPDA12 CNPDA11 CNPDA10 CNPDA9 CNPDA8 CNPDA7
—
—
CNPDA4
—
—
CNPDA1 CNPDA0
0000
ANSELA 0E0E
—
—
—
—
—
ANSA4
—
—
Legend:
ANSA11
—
—
—
—
ANSA1
ANSA0
1813
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-47:
File
Addr.
Name
Preliminary
TRISB
ANSA12
0E10
PORTB REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISB15
TRISB14
TRISB13
TRISB12
TRISB11
TRISB10
TRISB9
TRISB8
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
FFFF
RB15
RB14
RB13
RB12
RB11
RB10
RB9
RB8
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx
PORTB 0E12
LATB
0E14
LATB15
LATB14
LATB13
LATB12
LATB11
LATB10
LATB9
LATB8
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx
ODCB
0E16
ODCB15
ODCB14
ODCB13
ODCB12
ODCB11
ODCB10
ODCB9
ODCB8
ODCB7
ODCB6
ODCB5
ODCB4
ODCB3
ODCB2
ODCB1
ODCB0
0000
CNENB 0E18 CNIEB15
CNIEB14
CNIEB13
CNIEB12
CNIEB11
CNIEB10
CNIEB9
CNIEB8
CNIEB7
CNIEB6
CNIEB5
CNIEB4
CNIEB3
CNIEB2
CNIEB1
CNIEB0
0000
CNPUB 0E1A CNPUB15 CNPUB14 CNPUB13 CNPUB12 CNPUB11 CNPUB10 CNPUB9 CNPUB8 CNPUB7 CNPUB6 CNPUB5 CNPUB4 CNPUB3 CNPUB2 CNPUB1 CNPUB0
0000
CNPDB 0E1C CNPDB15 CNPDB14 CNPDB13 CNPDB12 CNPDB11 CNPDB10 CNPDB9 CNPDB8 CNPDB7 CNPDB6 CNPDB5 CNPDB4 CNPDB3 CNPDB2 CNPDB1 CNPDB0
0000
ANSELB 0E1E
ANSB0
010F
All
Resets
Legend:
—
—
—
—
—
—
ANSB8
—
—
—
—
ANSB3
ANSB2
ANSB1
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-48:
File
Name
—
PORTC REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
DS70657E-page 97
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TRISC
0E20
TRISC15
—
TRISC13
TRISC12
TRISC11
TRISC10
TRISC9
TRISC8
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
BFFF
PORTC
0E22
RC15
—
RC13
RC12
RC11
RC10
RC9
RC8
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx
LATC
0E24
LATC15
—
LATC13
LATC12
LATC11
LATC10
LATC9
LATC8
LATC7
LATC6
LATC5
LATC4
LATC3
LATC2
LATC1
LATC0
xxxx
ODCC
0E26
ODCC15
—
ODCC13
ODCC12
ODCC11
ODCC10
ODCC9
ODCC8
ODCC7
ODCC6
ODCC5
ODCC4
ODCC3
ODCC2
ODCC1
ODCC0
0000
CNENC
0E28
CNIEC15
—
CNIEC13
CNIEC12
CNIEC11
CNIEC10
CNIEC9
CNIEC8
CNIEC7
CNIEC6
CNIEC5
CNIEC4
CNIEC3
CNIEC2
CNIEC1
CNIEC0
0000
CNPUC
0E2A CNPUC15
—
CNPUC13 CNPUC12 CNPUC11 CNPUC10 CNPUC9 CNPUC8 CNPUC7 CNPUC6 CNPUC5 CNPUC4 CNPUC3 CNPUC2 CNPUC1 CNPUC0
0000
CNPDC
0E2C CNPDC15
—
CNPDC13 CNPDC12 CNPDC11 CNPDC10 CNPDC9 CNPDC8 CNPDC7 CNPDC6 CNPDC5 CNPDC4 CNPDC3 CNPDC2 CNPDC1 CNPDC0
0000
ANSELC 0E2E
Legend:
—
—
—
—
ANSC11
—
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
ANSC2
ANSC1
ANSC0
0807
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-46:
File
Name
PORTD REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISD
0E30
—
—
—
—
—
—
—
TRISD8
—
TRISD6
TRISD5
—
—
—
—
—
0160
PORTD
0E32
—
—
—
—
—
—
—
RD8
—
RD6
RD5
—
—
—
—
—
xxxx
LATD
0E34
—
—
—
—
—
—
—
LATD8
—
LATD6
LATD5
—
—
—
—
—
xxxx
ODCD
0E36
—
—
—
—
—
—
—
ODCD8
—
ODCD6
ODCD5
—
—
—
—
—
0000
CNEND 0E38
—
—
—
—
—
—
—
CNIED8
—
CNIED6
CNIED5
—
—
—
—
—
0000
CNPUD 0E3A
—
—
—
—
—
—
—
CNPUD8
—
CNPUD6 CNPUD5
—
—
—
—
—
0000
CNPDD 0E3C
—
—
—
—
—
—
—
CNPDD8
—
CNPDD6 CNPDD5
—
—
—
—
—
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-50:
File
Name
PORTE REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
Preliminary
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISE
0E40
TRISE15
TRISE14
TRISE13
TRISE12
—
—
—
—
—
—
—
—
—
—
—
—
F000
PORTE
0E42
RE15
RE14
RE13
RE12
—
—
—
—
—
—
—
—
—
—
—
—
xxxx
LATE
0E44
LATE15
LATE14
LATE13
LATE12
—
—
—
—
—
—
—
—
—
—
—
—
xxxx
ODCE
0E46
ODCE15
ODCE14
ODCE13
ODCE12
—
—
—
—
—
—
—
—
—
—
—
—
0000
CNENE
0E48
CNIEE15
CNIEE14
CNIEE13
CNIEE12
—
—
—
—
—
—
—
—
—
—
—
—
0000
CNPUE
0E4A CNPUE15 CNPUE14 CNPUE13 CNPUE12
—
—
—
—
—
—
—
—
—
—
—
—
0000
CNPDE
0E4C CNPDE15 CNPDE14 CNPDE13 CNPDE12
—
—
—
—
—
—
—
—
—
—
—
—
0000
—
—
—
—
—
—
—
—
—
—
—
—
0000
ANSELE 0E4E
Legend:
ANSE14
ANSE13
ANSE12
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-51:
File
Name
ANSE15
PORTF REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
© 2011-2012 Microchip Technology Inc.
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISF
0E50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TRISF1
TRISF0
0173
PORTF
0E52
—
—
—
—
—
—
—
—
—
—
—
—
—
—
RF1
RF0
xxxx
LATF
0E54
—
—
—
—
—
—
—
—
—
—
—
—
—
—
LATF1
LATF0
xxxx
ODCF
0E56
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ODCF1
ODCF0
0000
CNENF
0E58
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CNIEF1
CNIEF0
0000
CNPUF
0E5A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CNPUF1 CNPUF0
0000
CNPDF
0E5C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CNPDF1 CNPDF0
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 98
TABLE 4-49:
File
Name
PORTG REGISTER MAP FOR PIC24EPXXXGP/MC206 AND dsPIC33EPXXXGP/MC206/506 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISG
0E60
—
—
—
—
—
—
TRISG9
TRISG8
TRISG7
TRISG6
—
—
—
—
—
—
03C0
PORTG
0E62
—
—
—
—
—
—
RG9
RG8
RG7
RG6
—
—
—
—
—
—
xxxx
LATG
0E64
—
—
—
—
—
—
LATG9
LATG8
LATG7
LATG6
—
—
—
—
—
—
xxxx
ODCG
0E66
—
—
—
—
—
—
ODCG9
ODCG8
ODCG7
ODCG6
—
—
—
—
—
—
0000
CNENG
0E68
—
—
—
—
—
—
CNIEG9
CNIEG8
CNIEG7
CNIEG6
—
—
—
—
—
—
0000
CNPUG
0E6A
—
—
—
—
—
—
CNPUG9 CNPUG8 CNPUG7 CNPUG6
—
—
—
—
—
—
0000
CNPDG
0E6C
—
—
—
—
—
—
CNPDG9 CNPDG8 CNPDG7 CNPDG6
—
—
—
—
—
—
0000
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Preliminary
DS70657E-page 99
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-52:
File
Name
PORTA REGISTER MAP FOR PIC24EPXXXGP/MC204 AND dsPIC33EPXXXGP/MC204/504 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISA
0E00
—
—
—
—
—
TRISA10
TRISA9
TRISA8
TRISA7
—
—
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
079F
PORTA
0E02
—
—
—
—
—
RA10
RA9
RA8
RA7
—
—
RA4
RA3
RA2
RA1
RA0
0000
LATA
0E04
—
—
—
—
—
LATA10
LATA9
LATA8
LATA7
—
—
LATA4
LATA3
LATA2
LA1TA1
LA0TA0
0000
ODCA
0E06
—
—
—
—
—
ODCA10
ODCA9
ODCA8
ODCA7
—
—
ODCA4
ODCA3
ODCA2
ODCA1
ODCA0
0000
CNENA
0E08
—
—
—
—
—
CNIEA10
CNIEA9
CNIEA8
CNIEA7
—
—
CNIEA4
CNIEA3
CNIEA2
CNIEA1
CNIEA0
0000
CNPUA
0E0A
—
—
—
—
—
CNPUA10 CNPUA9 CNPUA8 CNPUA7
—
—
CNPUA4 CNPUA3 CNPUA2 CNPUA1 CNPUA0
0000
CNPDA
0E0C
—
—
—
—
—
CNPDA10 CNPDA9 CNPDA8 CNPDA7
—
—
CNPDA4 CNPDA3 CNPDA2 CNPDA1 CNPDA0
0000
ANSELA 0E0E
—
—
—
—
—
—
—
Legend:
—
—
—
ANSA4
—
—
ANSA1
ANSA0
0013
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-54:
Preliminary
0E10
PORTB REGISTER MAP FOR PIC24EPXXXGP/MC204 AND dsPIC33EPXXXGP/MC204/504 DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISB15
TRISB14
TRISB13
TRISB12
TRISB11
TRISB10
TRISB9
TRISB8
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
FFFF
RB15
RB14
RB13
RB12
RB11
RB10
RB9
RB8
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx
File
Addr.
Name
TRISB
—
PORTB 0E12
LATB
0E14
LATB15
LATB14
LATB13
LATB12
LATB11
LATB10
LATB9
LATB8
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx
ODCB
0E16
ODCB15
ODCB14
ODCB13
ODCB12
ODCB11
ODCB10
ODCB9
ODCB8
ODCB7
ODCB6
ODCB5
ODCB4
ODCB3
ODCB2
ODCB1
ODCB0
0000
CNENB 0E18 CNIEB15
CNIEB14
CNIEB13
CNIEB12
CNIEB11
CNIEB10
CNIEB9
CNIEB8
CNIEB7
CNIEB6
CNIEB5
CNIEB4
CNIEB3
CNIEB2
CNIEB1
CNIEB0
0000
CNPUB 0E1A CNPUB15 CNPUB14 CNPUB13 CNPUB12 CNPUB11 CNPUB10 CNPUB9 CNPUB8 CNPUB7 CNPUB6 CNPUB5 CNPUB4 CNPUB3 CNPUB2 CNPUB1 CNPUB0
0000
CNPDB 0E1C CNPDB15 CNPDB14 CNPDB13 CNPDB12 CNPDB11 CNPDB10 CNPDB9 CNPDB8 CNPDB7 CNPDB6 CNPDB5 CNPDB4 CNPDB3 CNPDB2 CNPDB1 CNPDB0
0000
ANSELB 0E1E
ANSB0
010F
Legend:
—
—
—
—
—
—
ANSB8
—
—
—
—
ANSB3
ANSB2
ANSB1
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
© 2011-2012 Microchip Technology Inc.
TABLE 4-55:
File
Name
—
PORTC REGISTER MAP FOR PIC24EPXXXGP/MC204 AND dsPIC33EPXXXGP/MC204/504 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISC
0E20
—
—
—
—
—
—
TRISC9
TRISC8
TRISC7
TRISC6
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
03FF
PORTC
0E22
—
—
—
—
—
—
RC9
RC8
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx
LATC
0E24
—
—
—
—
—
—
LATC9
LATC8
LATC7
LATC6
LATC5
LATC4
LATC3
LATC2
LATC1
LATC0
xxxx
ODCC
0E26
—
—
—
—
—
—
ODCC9
ODCC8
ODCC7
ODCC6
ODCC5
ODCC4
ODCC3
ODCC2
ODCC1
ODCC0
0000
CNENC
0E28
—
—
—
—
—
—
CNIEC9
CNIEC8
CNIEC7
CNIEC6
CNIEC5
CNIEC4
CNIEC3
CNIEC2
CNIEC1
CNIEC0
0000
CNPUC
0E2A
—
—
—
—
—
—
CNPUC9 CNPUC8 CNPUC7 CNPUC6 CNPUC5 CNPUC4 CNPUC3 CNPUC2 CNPUC1 CNPUC0
0000
CNPDC
0E2C
—
—
—
—
—
—
CNPDC9 CNPDC8 CNPDC7 CNPDC6 CNPDC5 CNPDC4 CNPDC3 CNPDC2 CNPDC1 CNPDC0
ANSELC 0E2E
—
—
—
—
—
—
Legend:
—
—
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
—
ANSC2
ANSC1
ANSC0
0000
0007
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 100
TABLE 4-53:
File
Name
PORTA REGISTER MAP FOR PIC24EPXXXGP/MC203 AND dsPIC33EPXXXGP/MC203/503 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISA
0E00
—
—
—
—
—
—
—
TRISA8
—
—
—
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
011F
PORTA
0E02
—
—
—
—
—
—
—
RA8
—
—
—
RA4
RA3
RA2
RA1
RA0
0000
LATA
0E04
—
—
—
—
—
—
—
LATA8
—
—
—
LATA4
LATA3
LATA2
LA1TA1
LA0TA0
0000
ODCA
0E06
—
—
—
—
—
—
—
ODCA8
—
—
—
ODCA4
ODCA3
ODCA2
ODCA1
ODCA0
0000
CNENA
0E08
—
—
—
—
—
—
—
CNIEA8
—
—
—
CNIEA4
CNIEA3
CNIEA2
CNIEA1
CNIEA0
0000
CNPUA
0E0A
—
—
—
—
—
—
—
CNPUA8
—
—
—
CNPUA4 CNPUA3 CNPUA2 CNPUA1 CNPUA0
0000
CNPDA
0E0C
—
—
—
—
—
—
—
CNPDA8
—
—
—
CNPDA4 CNPDA3 CNPDA2 CNPDA1 CNPDA0
0000
ANSELA 0E0E
—
—
—
—
—
—
—
—
—
—
—
Legend:
—
—
ANSA1
ANSA0
0013
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-57:
File
Addr.
Name
Preliminary
TRISB
ANSA4
0E10
PORTB REGISTER MAP FOR PIC24EPXXXGP/MC203 AND dsPIC33EPXXXGP/MC203/503 DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISB15
TRISB14
TRISB13
TRISB12
TRISB11
TRISB10
TRISB9
TRISB8
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
FFFF
RB15
RB14
RB13
RB12
RB11
RB10
RB9
RB8
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx
PORTB 0E12
LATB
0E14
LATB15
LATB14
LATB13
LATB12
LATB11
LATB10
LATB9
LATB8
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx
ODCB
0E16
ODCB15
ODCB14
ODCB13
ODCB12
ODCB11
ODCB10
ODCB9
ODCB8
ODCB7
ODCB6
ODCB5
ODCB4
ODCB3
ODCB2
ODCB1
ODCB0
0000
CNENB 0E18 CNIEB15
CNIEB14
CNIEB13
CNIEB12
CNIEB11
CNIEB10
CNIEB9
CNIEB8
CNIEB7
CNIEB6
CNIEB5
CNIEB4
CNIEB3
CNIEB2
CNIEB1
CNIEB0
0000
CNPUB 0E1A CNPUB15 CNPUB14 CNPUB13 CNPUB12 CNPUB11 CNPUB10 CNPUB9 CNPUB8 CNPUB7 CNPUB6 CNPUB5 CNPUB4 CNPUB3 CNPUB2 CNPUB1 CNPUB0
0000
CNPDB 0E1C CNPDB15 CNPDB14 CNPDB13 CNPDB12 CNPDB11 CNPDB10 CNPDB9 CNPDB8 CNPDB7 CNPDB6 CNPDB5 CNPDB4 CNPDB3 CNPDB2 CNPDB1 CNPDB0
0000
ANSELB 0E1E
ANSB0
010F
Legend:
—
—
—
—
—
—
ANSB8
—
—
—
—
ANSB3
ANSB2
ANSB1
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-58:
File
Name
—
PORTC REGISTER MAP FOR PIC24EPXXXGP/MC203 AND dsPIC33EPXXXGP/MC203/503 DEVICES ONLY
DS70657E-page 101
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISC
0E20
—
—
—
—
—
—
—
TRISC8
—
—
—
—
—
—
TRISC1
TRISC0
0107
PORTC
0E22
—
—
—
—
—
—
—
RC8
—
—
—
—
—
—
RC1
RC0
xxxx
LATC
0E24
—
—
—
—
—
—
—
LATC8
—
—
—
—
—
—
LATC1
LATC0
xxxx
ODCC
0E26
—
—
—
—
—
—
—
ODCC8
—
—
—
—
—
—
ODCC1
ODCC0
0000
CNENC
0E28
—
—
—
—
—
—
—
CNIEC8
—
—
—
—
—
—
CNIEC1
CNIEC0
0000
CNPUC
0E2A
—
—
—
—
—
—
—
CNPUC8
—
—
—
—
—
—
CNPUC1 CNPUC0
0000
CNPDC
0E2C
—
—
—
—
—
—
—
CNPDC8
—
—
—
—
—
—
CNPDC1 CNPDC0
0000
ANSELC 0E2E
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Legend:
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
ANSC1
ANSC0
0007
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
TABLE 4-56:
File
Name
PORTA REGISTER MAP FOR PIC24EPXXXGP/MC202 AND dsPIC33EPXXXGP/MC202/502 DEVICES ONLY
Addr.
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISA
0E00
—
—
—
—
—
—
—
—
—
—
—
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
001C
PORTA
0E02
—
—
—
—
—
—
—
—
—
—
—
RA4
RA3
RA2
RA1
RA0
0000
LATA
0E04
—
—
—
—
—
—
—
—
—
—
—
LATA4
LATA3
LATA2
LA1TA1
LA0TA0
0000
ODCA
0E06
—
—
—
—
—
—
—
—
—
—
—
ODCA4
ODCA3
ODCA2
ODCA1
ODCA0
0000
CNENA
0E08
—
—
—
—
—
—
—
—
—
—
—
CNIEA4
CNIEA3
CNIEA2
CNIEA1
CNIEA0
0000
CNPUA
0E0A
—
—
—
—
—
—
—
—
—
—
—
CNPUA4 CNPUA3 CNPUA2 CNPUA1 CNPUA0
0000
CNPDA
0E0C
—
—
—
—
—
—
—
—
—
—
—
CNPDA4 CNPDA3 CNPDA2 CNPDA1 CNPDA0
0000
ANSELA 0E0E
—
—
—
—
—
—
—
—
—
—
—
Legend:
—
—
ANSA1
ANSA0
0013
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-60:
File
Addr.
Name
Preliminary
TRISB
ANSA4
0E10
PORTB 0E12
PORTB REGISTER MAP FOR PIC24EPXXXGP/MC202 AND dsPIC33EPXXXGP/MC202/502 DEVICES ONLY
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
All
Resets
TRISB15
TRISB14
TRISB13
TRISB12
TRISB11
TRISB10
TRISB9
TRISB8
TRISB7
TRISB6
TRISB5
TRISB4
TRISB3
TRISB2
TRISB1
TRISB0
FFFF
RB15
RB14
RB13
RB12
RB11
RB10
RB9
RB8
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx
LATB
0E14
LATB15
LATB14
LATB13
LATB12
LATB11
LATB10
LATB9
LATB8
LATB7
LATB6
LATB5
LATB4
LATB3
LATB2
LATB1
LATB0
xxxx
ODCB
0E16
ODCB15
ODCB14
ODCB13
ODCB12
ODCB11
ODCB10
ODCB9
ODCB8
ODCB7
ODCB6
ODCB5
ODCB4
ODCB3
ODCB2
ODCB1
ODCB0
0000
CNENB 0E18 CNIEB15
CNIEB14
CNIEB13
CNIEB12
CNIEB11
CNIEB10
CNIEB9
CNIEB8
CNIEB7
CNIEB6
CNIEB5
CNIEB4
CNIEB3
CNIEB2
CNIEB1
CNIEB0
0000
CNPUB 0E1A CNPUB15 CNPUB14 CNPUB13 CNPUB12 CNPUB11 CNPUB10 CNPUB9 CNPUB8 CNPUB7 CNPUB6 CNPUB5 CNPUB4 CNPUB3 CNPUB2 CNPUB1 CNPUB0
0000
CNPDB 0E1C CNPDB15 CNPDB14 CNPDB13 CNPDB12 CNPDB11 CNPDB10 CNPDB9 CNPDB8 CNPDB7 CNPDB6 CNPDB5 CNPDB4 CNPDB3 CNPDB2 CNPDB1 CNPDB0
0000
ANSELB 0E1E
010F
Legend:
—
—
—
—
—
—
—
ANSB8
—
x = unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
—
—
—
ANSB3
ANSB2
ANSB1
ANSB0
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 102
TABLE 4-59:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.4.1
PAGED MEMORY SCHEME
Construction of the EDS address is shown in
Figure 4-1. When DSRPAG<9> = 0 and base address
bit EA<15> = 1, DSRPAG<8:0> is concatenated onto
EA<14:0> to form the 24-bit EDS read address.
Similarly when base address bit EA<15> = 1,
DSWPAG<8:0> is concatenated onto EA<14:0> to
form the 24-bit EDS write address.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X architecture
extends the available data space through a paging
scheme, which allows the available data space to be
accessed using MOV instructions in a linear fashion
for pre- and post-modified effective addresses (EA).
The upper half of base data space address is used
in conjunction with the data space page registers,
the 10-bit read page register (DSRPAG) or the 9-bit
write page register (DSWPAG), to form an extended
data space (EDS) address or Program Space
Visibility (PSV) address. The data space page
registers are located in the SFR space.
EXAMPLE 4-1:
EXTENDED DATA SPACE (EDS) READ ADDRESS GENERATION
16-bit DS EA
EA<15> = 0
(DSRPAG = don't care)
0
No EDS access
Byte
Select
EA
EA<15>
Generate
PSV address
Y
DSRPAG<9>
= 1?
Select
DSRPAG
0
1
EA
N
DSRPAG<8:0>
9 bits
15 bits
24-bit EDS EA
Byte
Select
Note: DS read access when DSRPAG = 0x000 will force an Address Error trap.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 103
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
EXAMPLE 4-2:
EXTENDED DATA SPACE (EDS) WRITE ADDRESS GENERATION
16-bit DS EA
Byte
Select
EA<15> = 0
(DSWPAG = don't care)
Generate
PSV address
No EDS access
0
EA
EA<15>
1
EA
DSWPAG<8:0>
9 bits
15 bits
24-bit EDS EA
Byte
Select
Note: DS read access when DSRPAG = 0x000 will force an Address Error trap.
The paged memory scheme provides access to
multiple 32-Kbyte windows in the EDS and PSV
memory. The data space page registers DSxPAG, in
combination with the upper half of data space address
can provide up to 16 Mbytes of additional address
space in the EDS and 8 Mbytes (DSRPAG only) of PSV
address space. The paged data memory space is
shown in Example 4-3.
The program space (PS) can be accessed with
DSRPAG of 0x200 or greater. Only reads from PS are
supported using the DSRPAG. Writes to PS are not
supported, so DSWPAG is dedicated to DS, including
EDS, only. The data space and EDS can be read from
and written to using DSRPAG and DSWPAG,
respectively.
DS70657E-page 104
Preliminary
© 2011-2012 Microchip Technology Inc.
PAGED DATA MEMORY SPACE
Local Data Space
EDS
(DSRPAG<9:0>/DSWPAG<8:0>)
DS_Addr<14:0>
0x0000
Page 0
0x7FFF
0x0000
0x7FFF
Table Address Space
(TBLPAG<7:0>)
Program Space
(Instruction & Data)
Reserved
(Will produce an
address error trap)
DS_Addr<15:0>
0x0000
EDS Page 0x001
(DSRPAG = 0x001)
(DSWPAG = 0x001)
Program Memory
(lsw - <15:0>)
0x00_0000
0xFFFF
DS_Addr<15:0>
0x0000
0x0000
SFR Registers
Preliminary
0x0FFF
0x1000
0x7FFF
0x0000
Up to 8 Kbyte
RAM
0x2FFF
0x3000
0x7FFF
0x8000
32 Kbyte
EDS Window
0x7FFF
0x0000
0xFFFF
0x7FFF
0x0000
0x7FFF
DS70657E-page 105
0x0000
0x7FFF
EDS Page 0x1FF
(DSRPAG = 0x1FF)
(DSWPAG = 0x1FF)
0x0000
EDS Page 0x200
(DSRPAG = 0x200)
No writes allowed
0x7F_FFFF
PSV
Program
Memory
(lsw)
EDS Page 0x2FF
(DSRPAG = 0x2FF)
No writes allowed
0xFFFF
Program Memory
(MSB - <23:16>)
0x00_0000
EDS Page 0x300
(DSRPAG = 0x300)
No writes allowed
PSV
Program
Memory
(MSB)
EDS Page 0x3FF
(DSRPAG = 0x3FF)
No writes allowed
0x7F_FFFF
(TBLPAG = 0x00)
lsw using
TBLRDL/TBLWTL
MSB using
TBLRDH/TBLWTH
(TBLPAG = 0x7F)
lsw using
TBLRDL/TBLWTL
MSB using
TBLRDH/TBLWTH
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
EXAMPLE 4-3:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Allocating different page registers for read and write
access allows the architecture to support data
movement between different pages in data memory.
This is accomplished by setting the DSRPAG register
value to the page from which you want to read, and
configuring the DSWPAG register to the page to which
it needs to be written. Data can also be moved from
different PSV to EDS pages, by configuring the
DSRPAG and DSWPAG registers to address PSV and
EDS space, respectively. The data can be moved
between pages by a single instruction.
When an EDS or PSV page overflow or underflow
occurs, EA<15> is cleared as a result of the register
indirect EA calculation. An overflow or underflow of the
EA in the EDS or PSV pages can occur at the page
boundaries when:
• The initial address prior to modification addresses
an EDS or PSV page
• The EA calculation uses pre- or post-modified
register indirect addressing. However, this does
not include register offset addressing
TABLE 4-61:
In general, when an overflow is detected, the DSxPAG
register is incremented, and the EA<15> bit is set to
keep the base address within the EDS or PSV window.
When an underflow is detected, the DSxPAG register is
decremented, and the EA<15> bit is set to keep the
base address within the EDS or PSV window. This
creates a linear EDS and PSV address space, but only
when using Register Indirect Addressing modes.
Exceptions to the operation described above arise
when entering and exiting the boundaries of page 0,
EDS, and PSV spaces. Table 4-61 lists the effects of
overflow and underflow scenarios at different
boundaries.
In the following cases, when overflow or underflow
occurs, the EA<15> bit is set and the DSxPAG is not
modified; therefore, the EA will wrap to the beginning of
the current page:
• Register indirect with register offset addressing
• Modulo Addressing
• Bit-reversed addressing
OVERFLOW AND UNDERFLOW SCENARIOS AT PAGE 0, EDS, and PSV SPACE
BOUNDARIES
O/U,
Operation
R/W
Before
After
DSxPAG
DS
EA<15>
Page
Description
DSxPAG
DS
EA<15>
DSRPAG = 0x1FF
1
EDS: Last page
DSRPAG = 0x1FF
0
See Note 1
DSRPAG = 0x2FF
1
PSV: Last lsw
page
DSRPAG = 0x300
1
PSV: First MSB
page
DSRPAG = 0x3FF
1
PSV: Last MSB
page
DSRPAG = 0x3FF
0
See Note 1
O,
Write
DSWPAG = 0x1FF
1
EDS: Last page
DSWPAG = 0x1FF
0
See Note 1
U,
Read
DSRPAG = 0x001
1
PSV page
DSRPAG = 0x001
0
See Note 1
DSRPAG = 0x200
1
PSV: First lsw
page
DSRPAG = 0x200
0
See Note 1
DSRPAG = 0x300
1
PSV: First MSB
page
DSRPAG = 0x2FF
1
PSV: Last lsw
page
O,
Read
O,
Read
[++Wn]
or
[Wn++]
O,
Read
[--Wn]
or
[Wn--]
U,
Read
U,
Read
Legend:
Note 1:
2:
3:
4:
Page
Description
O = Overflow, U = Underflow, R = Read, W = Write
The register indirect address now addresses a location in the base data space (0x0000-0x8000).
An EDS access with DSxPAG = 0x000 will generate an address error trap.
Only reads from PS are supported using DSRPAG. An attempt to write to PS using DSWPAG will generate
an address error trap.
Pseudo-linear addressing is not supported for large offsets.
DS70657E-page 106
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.4.2
EXTENDED X DATA SPACE
The lower portion of the base address space range
between 0x0000 and 0x2FFF is always accessible
regardless of the contents of the data space page
registers. It is indirectly addressable through the
register indirect instructions. It can be regarded as
being located in the default EDS page 0 (i.e., EDS
address range of 0x000000 to 0x002FFF with the base
address bit EA<15> = 0 for this address range).
However, page 0 cannot be accessed through upper
32 Kbytes, 0x8000 to 0xFFFF, of base data space in
combination with DSRPAG = 0x00 or DSWPAG =
0x00. Consequently, DSRPAG and DSWPAG are
initialized to 0x001 at Reset.
Note 1: DSxPAG should not be used to access
page 0. An EDS access with DSxPAG set
to 0x000 will generate an Address Error
trap.
The remaining pages including both EDS and PSV
pages are only accessible using the DSRPAG or
DSWPAG registers in combination with the upper
32 Kbytes, 0x8000 to 0xFFFF, of the base address,
where base address bit EA<15> = 1.
For example, when DSRPAG = 0x01 or DSWPAG =
0x01, accesses to the upper 32 Kbytes, 0x8000 to
0xFFFF, of the data space will map to the EDS address
range of 0x008000 to 0x00FFFF. When DSRPAG =
0x02 or DSWPAG = 0x02, accesses to the upper
32 Kbytes of the data space will map to the EDS
address range of 0x010000 to 0x017FFF and so on, as
shown in the EDS memory map in Figure 4-17.
For more information of the PSV page access using
data space page registers refer to 4.5 “Program
Space Visibility from Data Space” in Section 4.
“Program Memory” (DS70613) of the “dsPIC33E/
PIC24E Family Reference Manual”.
2: Clearing the DSxPAG in software has no
effect.
FIGURE 4-17:
EDS MEMORY MAP
EA<15:0>
0x0000
Conventional
DS Address
SFR/DS
(PAGE 0)
0x8000
DS
PAGE 1
0x008000
0xFFFF
PAGE 2
PAGE 3
0x010000
0x018000
DSRPAG<9> = 0
EDS EA Address (24-bits)
(DSRPAG<8:0>, EA<14:0>)
(DSWPAG<8:0>, EA<14:0>)
PAGE 1FD
PAGE 1FE
PAGE 1FF
© 2011-2012 Microchip Technology Inc.
Preliminary
0xFE8000
0xFF0000
0xFF8000
DS70657E-page 107
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.4.3
DATA MEMORY ARBITRATION AND
BUS MASTER PRIORITY
that of the CPU maintain the same priority relationship
relative to each other. The priority schemes for bus
masters with different MSTRPR values are tabulated in
Table 4-62.
EDS accesses from bus masters in the system are
arbitrated.
This bus master priority control allows the user
application to manipulate the real-time response of the
system, either statically during initialization, or
dynamically in response to real-time events.
The arbiter for data memory (including EDS) arbitrates
between the CPU, the DMA, and the ICD module. In
the event of coincidental access to a bus by the bus
masters, the arbiter determines which bus master
access has the highest priority. The other bus masters
are suspended and processed after the access of the
bus by the bus master with the highest priority.
TABLE 4-62:
By default, the CPU is bus master 0 (M0) with the
highest priority, and the ICD is bus master 4 (M4) with
the lowest priority. The remaining bus master (DMA
controller) is allocated to M3, (M1 and M2 are reserved
and cannot be used). The user application may raise or
lower the priority of the DMA controller to be above that
of the CPU by setting the appropriate bits in the EDS
Bus Master Priority Control (MSTRPR) register. All bus
masters with raised priorities will maintain the same
priority relationship relative to each other (i.e., M1
being highest and M3 being lowest with M2 in
between). Also, all the bus masters with priorities below
FIGURE 4-18:
DATA MEMORY BUS
ARBITER PRIORITY
MSTRPR<15:0> Bit Setting(1)
Priority
0x0000
0x0020
M0 (highest)
CPU
DMA
M1
Reserved
CPU
M2
Reserved
Reserved
M3
DMA
Reserved
M4 (lowest)
ICD
ICD
Note 1:
All other values of MSTRPR<15:0> are
Reserved.
ARBITER ARCHITECTURE
ICD
Reserved
DMA
CPU
MSTRPR<15:0>
M0
M1
M2
M3
M4
Data Memory Arbiter
SRAM
DS70657E-page 108
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.4.4
SOFTWARE STACK
FIGURE 4-19:
The W15 register serves as a dedicated software Stack
Pointer (SP) and is automatically modified by exception
processing, subroutine calls and returns; however,
W15 can be referenced by any instruction in the same
manner as all other W registers. This simplifies
reading, writing and manipulating of the Stack Pointer
(for example, creating stack frames).
To protect against misaligned stack
accesses, W15<0> is fixed to ‘0’ by the
hardware.
W15 is initialized to 0x1000 during all Resets. This
address ensures that the SP points to valid RAM in all
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices and permits
stack availability for non-maskable trap exceptions.
These can occur before the SP is initialized by the user
software. You can reprogram the SP during
initialization to any location within data space.
The Stack Pointer always points to the first available
free word and fills the software stack working from
lower toward higher addresses. Figure 4-19 illustrates
how it pre-decrements for a stack pop (read) and postincrements for a stack push (writes).
When the PC is pushed onto the stack, PC<15:0> is
pushed onto the first available stack word, then
PC<22:16> is pushed into the second available stack
location. For a PC push during any CALL instruction,
the MSB of the PC is zero-extended before the push,
as shown in Figure 4-19. During exception processing,
the MSB of the PC is concatenated with the lower 8 bits
of the CPU STATUS register, SR. This allows the
contents of SRL to be preserved automatically during
interrupt processing.
Note 1: To maintain system stack pointer (W15)
coherency, W15 is never subject to
(EDS) paging, and is therefore restricted
to an address range of 0x0000 to
0xFFFF. The same applies to the W14
when used as a Stack Frame Pointer
(SFA = 1).
2: As the stack can be placed in, and can
access, X and Y spaces, care must be
taken regarding its use, particularly with
regard to local automatic variables in a C
development environment
4.5
0
PC<15:1>
SUBR
W15 (before CALL)
b‘000000000’PC<22:16>
<Free Word>
W15 (after CALL)
Instruction Addressing Modes
The addressing modes shown in Table 4-63 form the
basis of the addressing modes optimized to support the
specific features of individual instructions. The
addressing modes provided in the MAC class of
instructions differ from those in the other instruction
types.
4.5.1
FILE REGISTER INSTRUCTIONS
Most file register instructions use a 13-bit address field
(f) to directly address data present in the first 8192
bytes of data memory (near data space). Most file
register instructions employ a working register, W0,
which is denoted as WREG in these instructions. The
destination is typically either the same file register or
WREG (with the exception of the MUL instruction),
which writes the result to a register or register pair. The
MOV instruction allows additional flexibility and can
access the entire data space.
4.5.2
MCU INSTRUCTIONS
The three-operand MCU instructions are of the form:
Operand 3 = Operand 1 <function> Operand 2
where Operand 1 is always a working register (that is,
the addressing mode can only be Register Direct),
which is referred to as Wb. Operand 2 can be a W register, fetched from data memory, or a 5-bit literal. The
result location can be either a W register or a data
memory location. The following addressing modes are
supported by MCU instructions:
•
•
•
•
•
Register Direct
Register Indirect
Register Indirect Post-Modified
Register Indirect Pre-Modified
5-bit or 10-bit Literal
Note:
© 2011-2012 Microchip Technology Inc.
15
CALL
Stack Grows Toward
Higher Address
Note:
0x0000
CALL STACK FRAME
Preliminary
Not all instructions support all the
addressing modes given above. Individual instructions can support different
subsets of these addressing modes.
DS70657E-page 109
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 4-63:
FUNDAMENTAL ADDRESSING MODES SUPPORTED
Addressing Mode
File Register Direct
Description
The address of the file register is specified explicitly.
Register Direct
The contents of a register are accessed directly.
Register Indirect
The contents of Wn forms the Effective Address (EA).
Register Indirect Post-Modified
The contents of Wn forms the EA. Wn is post-modified (incremented
or decremented) by a constant value.
Register Indirect Pre-Modified
Wn is pre-modified (incremented or decremented) by a signed constant value
to form the EA.
Register Indirect with Register Offset The sum of Wn and Wb forms the EA.
(Register Indexed)
Register Indirect with Literal Offset
4.5.3
The sum of Wn and a literal forms the EA.
4.5.4
MOVE AND ACCUMULATOR
INSTRUCTIONS
Move
instructions,
which
apply
to
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices, and the DSP
accumulator class of instructions, which apply to the
dsPIC33EPXXXMC20X/50X
and
dsPIC33EPXXXGP50X devices, provide a greater
degree of addressing flexibility than other instructions.
In addition to the addressing modes supported by most
MCU instructions, move and accumulator instructions
also support Register Indirect with Register Offset
Addressing mode, also referred to as Register Indexed
mode.
Note:
For the MOV instructions, the addressing
mode specified in the instruction can differ
for the source and destination EA.
However, the 4-bit Wb (Register Offset)
field is shared by both source and
destination (but typically only used by
one).
In summary, the following addressing modes are
supported by move and accumulator instructions:
•
•
•
•
•
•
•
•
Register Direct
Register Indirect
Register Indirect Post-modified
Register Indirect Pre-modified
Register Indirect with Register Offset (Indexed)
Register Indirect with Literal Offset
8-bit Literal
16-bit Literal
Note:
DS70657E-page 110
The dual source operand DSP instructions (CLR, ED,
EDAC, MAC, MPY, MPY.N, MOVSAC and MSC), also referred
to as MAC instructions, use a simplified set of addressing
modes to allow the user application to effectively
manipulate the data pointers through register indirect
tables.
The two-source operand prefetch registers must be
members of the set {W8, W9, W10, W11}. For data
reads, W8 and W9 are always directed to the X RAGU,
and W10 and W11 are always directed to the Y AGU.
The effective addresses generated (before and after
modification) must, therefore, be valid addresses within
X data space for W8 and W9 and Y data space for W10
and W11.
Note:
Register Indirect with Register Offset
Addressing mode is available only for W9
(in X space) and W11 (in Y space).
In summary, the following addressing modes are
supported by the MAC class of instructions:
•
•
•
•
•
Register Indirect
Register Indirect Post-Modified by 2
Register Indirect Post-Modified by 4
Register Indirect Post-Modified by 6
Register Indirect with Register Offset (Indexed)
4.5.5
Not all instructions support all the
addressing modes given above. Individual
instructions may support different subsets
of these addressing modes.
MAC INSTRUCTIONS
(dsPIC33EPXXXMC20X/50X and
dsPIC33EPXXXGP50X DEVICES
ONLY)
OTHER INSTRUCTIONS
Besides the addressing modes outlined previously, some
instructions use literal constants of various sizes. For
example, BRA (branch) instructions use 16-bit signed
literals to specify the branch destination directly, whereas
the DISI instruction uses a 14-bit unsigned literal field. In
some instructions, such as ULNK, the source of an
operand or result is implied by the opcode itself. Certain
operations, such as NOP, do not have any operands.
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.6
Modulo Addressing
(dsPIC33EPXXXMC20X/50X and
dsPIC33EPXXXGP50X Devices
Only)
Modulo Addressing mode is a method of providing an
automated means to support circular data buffers using
hardware. The objective is to remove the need for
software to perform data address boundary checks
when executing tightly looped code, as is typical in
many DSP algorithms.
Modulo Addressing can operate in either data or program
space (since the data pointer mechanism is essentially
the same for both). One circular buffer can be supported
in each of the X (which also provides the pointers into
program space) and Y data spaces. Modulo Addressing
can operate on any W register pointer. However, it is not
advisable to use W14 or W15 for Modulo Addressing
since these two registers are used as the Stack Frame
Pointer and Stack Pointer, respectively.
In general, any particular circular buffer can be configured to operate in only one direction as there are
certain restrictions on the buffer start address (for incrementing buffers), or end address (for decrementing
buffers), based upon the direction of the buffer.
The only exception to the usage restrictions is for
buffers that have a power-of-two length. As these
buffers satisfy the start and end address criteria, they
can operate in a bidirectional mode (that is, address
boundary checks are performed on both the lower and
upper address boundaries).
4.6.1
START AND END ADDRESS
The Modulo Addressing scheme requires that a
starting and ending address be specified and loaded
into the 16-bit Modulo Buffer Address registers:
XMODSRT, XMODEND, YMODSRT and YMODEND
(see Table 4-1).
Note:
Y space Modulo Addressing EA calculations assume word-sized data (LSb of
every EA is always clear).
The length of a circular buffer is not directly specified. It
is determined by the difference between the
corresponding start and end addresses. The maximum
possible length of the circular buffer is 32K words
(64 Kbytes).
4.6.2
W ADDRESS REGISTER
SELECTION
The Modulo and Bit-Reversed Addressing Control
register, MODCON<15:0>, contains enable flags as well
as a W register field to specify the W Address registers.
The XWM and YWM fields select the registers that
operate with Modulo Addressing:
• If XWM = 1111, X RAGU and X WAGU Modulo
Addressing is disabled
• If YWM = 1111, Y AGU Modulo Addressing is
disabled
The X Address Space Pointer W register (XWM), to
which Modulo Addressing is to be applied, is stored in
MODCON<3:0> (see Table 4-1). Modulo Addressing is
enabled for X data space when XWM is set to any value
other than ‘1111’ and the XMODEN bit is set at
MODCON<15>.
The Y Address Space Pointer W register (YWM) to
which Modulo Addressing is to be applied is stored in
MODCON<7:4>. Modulo Addressing is enabled for Y
data space when YWM is set to any value other than
‘1111’ and the YMODEN bit is set at MODCON<14>.
FIGURE 4-20:
MODULO ADDRESSING OPERATION EXAMPLE
Byte
Address
0x1100
0x1163
Start Addr = 0x1100
End Addr = 0x1163
Length = 0x0032 words
© 2011-2012 Microchip Technology Inc.
MOV
MOV
MOV
MOV
MOV
MOV
#0x1100, W0
W0, XMODSRT
#0x1163, W0
W0, MODEND
#0x8001, W0
W0, MODCON
MOV
#0x0000, W0
;W0 holds buffer fill value
MOV
#0x1110, W1
;point W1 to buffer
DO
AGAIN, #0x31
MOV
W0, [W1++]
AGAIN: INC W0, W0
Preliminary
;set modulo start address
;set modulo end address
;enable W1, X AGU for modulo
;fill the 50 buffer locations
;fill the next location
;increment the fill value
DS70657E-page 111
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.6.3
MODULO ADDRESSING
APPLICABILITY
4.7.1
Modulo Addressing can be applied to the Effective
Address (EA) calculation associated with any W
register. Address boundaries check for addresses
equal to:
• The upper boundary addresses for incrementing
buffers
• The lower boundary addresses for decrementing
buffers
It is important to realize that the address boundaries
check for addresses less than or greater than the upper
(for incrementing buffers) and lower (for decrementing
buffers) boundary addresses (not just equal to).
Address changes can, therefore, jump beyond
boundaries and still be adjusted correctly.
Note:
4.7
The modulo corrected effective address is
written back to the register only when PreModify or Post-Modify Addressing mode is
used to compute the effective address.
When an address offset (such as [W7 +
W2]) is used, Modulo Address correction
is performed but the contents of the
register remain unchanged.
Bit-Reversed Addressing
(dsPIC33EPXXXMC20X/50X and
dsPIC33EPXXXGP50X Devices
Only)
Bit-Reversed Addressing mode is intended to simplify
data reordering for radix-2 FFT algorithms. It is
supported by the X AGU for data writes only.
The modifier, which can be a constant value or register
contents, is regarded as having its bit order reversed.
The address source and destination are kept in normal
order. Thus, the only operand requiring reversal is the
modifier.
BIT-REVERSED ADDRESSING
IMPLEMENTATION
Bit-Reversed Addressing mode is enabled in any of
these situations:
• BWM bits (W register selection) in the MODCON
register are any value other than ‘1111’ (the stack
cannot be accessed using Bit-Reversed
Addressing)
• The BREN bit is set in the XBREV register
• The addressing mode used is Register Indirect
with Pre-Increment or Post-Increment
If the length of a bit-reversed buffer is M = 2N bytes,
the last ‘N’ bits of the data buffer start address must
be zeros.
XB<14:0> is the Bit-Reversed Address modifier, or
‘pivot point,’ which is typically a constant. In the case of
an FFT computation, its value is equal to half of the FFT
data buffer size.
Note:
All bit-reversed EA calculations assume
word-sized data (LSb of every EA is
always clear). The XB value is scaled
accordingly to generate compatible (byte)
addresses.
When enabled, Bit-Reversed Addressing is executed
only for Register Indirect with Pre-Increment or PostIncrement Addressing and word-sized data writes. It
does not function for any other addressing mode or for
byte-sized data, and normal addresses are generated
instead. When Bit-Reversed Addressing is active, the
W Address Pointer is always added to the address
modifier (XB), and the offset associated with the
Register Indirect Addressing mode is ignored. In
addition, as word-sized data is a requirement, the LSb
of the EA is ignored (and always clear).
Note:
Modulo addressing and bit-reversed
addressing can be enabled simultaneously
using the same W register, but bit-reversed
addressing operation will always take
precedence for data writes when enabled.
If Bit-Reversed Addressing has already been enabled
by setting the BREN (XBREV<15>) bit, a write to the
XBREV register should not be immediately followed by
an indirect read operation using the W register that has
been designated as the bit-reversed pointer.
DS70657E-page 112
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 4-21:
BIT-REVERSED ADDRESS EXAMPLE
Sequential Address
b15 b14 b13 b12 b11 b10 b9 b8
b7 b6 b5 b4
b3 b2
b1
0
Bit Locations Swapped Left-to-Right
Around Center of Binary Value
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b1 b2 b3 b4
0
Bit-Reversed Address
Pivot Point
TABLE 4-64:
XB = 0x0008 for a 16-Word Bit-Reversed Buffer
BIT-REVERSED ADDRESS SEQUENCE (16-ENTRY)
Normal Address
Bit-Reversed Address
A3
A2
A1
A0
Decimal
A3
A2
A1
A0
Decimal
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
8
0
0
1
0
2
0
1
0
0
4
0
0
1
1
3
1
1
0
0
12
0
1
0
0
4
0
0
1
0
2
0
1
0
1
5
1
0
1
0
10
0
1
1
0
6
0
1
1
0
6
0
1
1
1
7
1
1
1
0
14
1
0
0
0
8
0
0
0
1
1
1
0
0
1
9
1
0
0
1
9
1
0
1
0
10
0
1
0
1
5
1
0
1
1
11
1
1
0
1
13
1
1
0
0
12
0
0
1
1
3
1
1
0
1
13
1
0
1
1
11
1
1
1
0
14
0
1
1
1
7
1
1
1
1
15
1
1
1
1
15
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 113
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.8
Interfacing Program and Data
Memory Spaces
Table instructions allow an application to read or write
to small areas of the program memory. This capability
makes the method ideal for accessing data tables that
need to be updated periodically. It also allows access
to all bytes of the program word. The remapping
method allows an application to access a large block of
data on a read-only basis, which is ideal for look-ups
from a large table of static data. The application can
only access the least significant word of the program
word.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X architecture uses a
24-bit-wide program space and a 16-bit-wide data
space. The architecture is also a modified Harvard
scheme, meaning that data can also be present in the
program space. To use this data successfully, it must
be accessed in a way that preserves the alignment of
information in both spaces.
Aside from normal execution, the architecture of the
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices provides two
methods by which program space can be accessed
during operation:
• Using table instructions to access individual bytes
or words anywhere in the program space
• Remapping a portion of the program space into
the data space (Program Space Visibility)
TABLE 4-65:
PROGRAM SPACE ADDRESS CONSTRUCTION
Program Space Address
Access
Space
Access Type
<23>
<22:16>
<15>
<14:1>
Instruction Access
(Code Execution)
User
TBLRD/TBLWT
(Byte/Word Read/Write)
User
TBLPAG<7:0>
Configuration
TBLPAG<7:0>
Data EA<15:0>
1xxx xxxx
xxxx xxxx xxxx xxxx
FIGURE 4-22:
PC<22:1>
0
0xx
xxxx
xxxx
0xxx xxxx
<0>
0
xxxx
xxxx xxx0
Data EA<15:0>
xxxx xxxx xxxx xxxx
DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION
Program Counter(1)
Program Counter
0
0
23 bits
EA
Table Operations(2)
1/0
1/0
TBLPAG
8 bits
16 bits
24 bits
User/Configuration
Space Select
Byte Select
Note 1: The Least Significant bit (LSb) of program space addresses is always fixed as ‘0’ to maintain word
alignment of data in the program and data spaces.
2: Table operations are not required to be word aligned. Table read operations are permitted in the
configuration memory space.
DS70657E-page 114
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
4.8.1
DATA ACCESS FROM PROGRAM
MEMORY USING TABLE
INSTRUCTIONS
The TBLRDL and TBLWTL instructions offer a direct
method of reading or writing the lower word of any
address within the program space without going
through data space. The TBLRDH and TBLWTH
instructions are the only method to read or write the
upper 8 bits of a program space word as data.
The PC is incremented by two for each successive
24-bit program word. This allows program memory
addresses to directly map to data space addresses.
Program memory can thus be regarded as two 16-bitwide word address spaces, residing side by side, each
with the same address range. TBLRDL and TBLWTL
access the space that contains the least significant
data word. TBLRDH and TBLWTH access the space that
contains the upper data byte.
Two table instructions are provided to move byte or
word-sized (16-bit) data to and from program space.
Both function as either byte or word operations.
• TBLRDL (Table Read Low):
- In Word mode, this instruction maps the
lower word of the program space
location (P<15:0>) to a data address
(D<15:0>)
FIGURE 4-23:
- In Byte mode, either the upper or lower byte
of the lower program word is mapped to the
lower byte of a data address. The upper byte
is selected when Byte Select is ‘1’; the lower
byte is selected when it is ‘0’.
• TBLRDH (Table Read High):
- In Word mode, this instruction maps the entire
upper word of a program address (P<23:16>)
to a data address. The ‘phantom’ byte
(D<15:8>), is always ‘0’.
- In Byte mode, this instruction maps the upper
or lower byte of the program word to D<7:0>
of the data address, in the TBLRDL instruction. The data is always ‘0’ when the upper
‘phantom’ byte is selected (Byte Select = 1).
In a similar fashion, two table instructions, TBLWTH
and TBLWTL, are used to write individual bytes or
words to a program space address. The details of
their operation are explained in Section 5.0 “Flash
Program Memory”.
For all table operations, the area of program memory
space to be accessed is determined by the Table Page
register (TBLPAG). TBLPAG covers the entire program
memory space of the device, including user application
and configuration spaces. When TBLPAG<7> = 0, the
table page is located in the user memory space. When
TBLPAG<7> = 1, the page is located in configuration
space.
ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS
Program Space
TBLPAG
02
23
15
0
0x000000
23
16
8
0
00000000
0x020000
0x030000
00000000
00000000
00000000
‘Phantom’ Byte
TBLRDH.B (Wn<0> = 0)
TBLRDL.B (Wn<0> = 1)
TBLRDL.B (Wn<0> = 0)
TBLRDL.W
0x800000
© 2011-2012 Microchip Technology Inc.
The address for the table operation is determined by the data EA
within the page defined by the TBLPAG register.
Only read operations are shown; write operations are also valid in
the user memory area.
Preliminary
DS70657E-page 115
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 116
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
5.0
FLASH PROGRAM MEMORY
programming clock and programming data (one of the
alternate programming pin pairs: PGECx/PGEDx), and
three other lines for power (VDD), ground (VSS) and
Master Clear (MCLR). This allows customers to
manufacture boards with unprogrammed devices and
then program the device just before shipping the
product. This also allows the most recent firmware or a
custom firmware to be programmed.
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet,
refer to Section 5. “Flash Programming” (DS70609) of the “dsPIC33E/
PIC24E Family Reference Manual”,
which is available from the Microchip web
site (www.microchip.com).
RTSP is accomplished using TBLRD (table read) and
TBLWT (table write) instructions. With RTSP, the user
application can write program memory data a single
program memory word, and erase program memory in
blocks or ‘pages’ of 1024 instructions (3072 bytes) at a
time.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
5.1
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices contain
internal Flash program memory for storing and
executing application code. The memory is readable,
writable and erasable during normal operation over the
entire VDD range.
Flash memory can be programmed in two ways:
Table Instructions and Flash
Programming
Regardless of the method used, all programming of
Flash memory is done with the table read and table
write instructions. These allow direct read and write
access to the program memory space from the data
memory while the device is in normal operating mode.
The 24-bit target address in the program memory is
formed using bits <7:0> of the TBLPAG register and the
Effective Address (EA) from a W register specified in
the table instruction, as shown in Figure 5-1.
• In-Circuit Serial Programming™ (ICSP™)
programming capability
• Run-Time Self-Programming (RTSP)
The TBLRDL and the TBLWTL instructions are used to
read or write to bits <15:0> of program memory.
TBLRDL and TBLWTL can access program memory in
both Word and Byte modes.
ICSP
allows
for
a
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X device to be serially programmed while in the
end application circuit. This is done with two lines for
The TBLRDH and TBLWTH instructions are used to read
or write to bits <23:16> of program memory. TBLRDH
and TBLWTH can also access program memory in Word
or Byte mode.
FIGURE 5-1:
ADDRESSING FOR TABLE REGISTERS
24 bits
Using
Program Counter
Program Counter
0
0
Working Reg EA
Using
Table Instruction
1/0
TBLPAG Reg
8 bits
User/Configuration
Space Select
© 2011-2012 Microchip Technology Inc.
16 bits
24-bit EA
Preliminary
Byte
Select
DS70657E-page 117
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
5.2
RTSP Operation
5.4
RTSP allows the user application to erase a single
page of memory, and to program two instruction words
at a time. See the General Purpose and Motor Control
Family tables (Table 1 and Table , respectively) for the
page sizes of each device.
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
For more information on erasing and programming
Flash memory, refer to Section 5. “Flash Programming” (DS70609) in the “dsPIC33E/PIC24E Family
Reference Manual”.
5.3
For erase and program times, refer to parameters
DI37a and DI37b (Page Erase Time), and DI38a and
DI38b (Word Write Cycle Time), in Table 30-13: “DC
Characteristics: Program Memory”.
Setting the WR bit (NVMCON<15>) starts the operation, and the WR bit is automatically cleared when the
operation is finished.
5.3.1
Note:
Programming Operations
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode. The processor stalls (waits) until the
programming operation is finished.
PROGRAMMING ALGORITHM FOR
FLASH PROGRAM MEMORY
Programmers can program two adjacent words
(24 bits x 2) of program Flash memory at a time on
every other word address boundary (0x000002,
0x000006, 0x00000A, etc.). To do this, it is necessary
to erase page that contains the desired address of the
location the user wants to change.
For protection against accidental operations, the write
initiate sequence for NVMKEY must be used to allow
any erase or program operation to proceed. After the
programming command has been executed, the user
application must wait for the programming time until
programming is complete. The two instructions following the start of the programming sequence should be
NOPs.
Refer to Section 5. “Flash Programming” (DS70609)
in the “dsPIC33E/PIC24E Family Reference Manual”
for details and codes examples on programming using
RTSP.
DS70657E-page 118
Flash Memory Resources
5.4.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 5. “Flash Programming” (DS70609)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
5.5
Control Registers
Four SFRs are used to read and write the program
Flash memory: NVMCON, NVMKEY, NVMADRU, and
NVMADR.
The NVMCON register (Register 5-1) controls which
blocks are to be erased, which memory type is to be
programmed and the start of the programming cycle.
NVMKEY (Register 5-4) is a write-only register that is
used for write protection. To start a programming or
erase sequence, the user application must
consecutively write 0x55 and 0xAA to the NVMKEY
register.
There are two NVM address registers: NVMADRU and
NVMADR. These two registers, when concatenated,
form the 24-bit effective address (EA) of the selected
word for programming operations, or the selected page
for erase operations.
The NVMADRU register is used to hold the upper 8 bits
of the EA, while the NVMADR register is used to hold
the lower 16 bits of the EA.
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 5-1:
R/SO-0(1)
NVMCON: NONVOLATILE MEMORY (NVM) CONTROL REGISTER
R/W-0(1)
WR
WREN
R/W-0(1)
R/W-0
U-0
U-0
U-0
U-0
WRERR
NVMSIDL(2)
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
—
—
—
—
R/W-0(1)
R/W-0(1)
R/W-0(1)
R/W-0(1)
NVMOP<3:0>(3,4)
bit 7
bit 0
Legend:
SO = Settable only bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
WR: Write Control bit
1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is
cleared by hardware once operation is complete
0 = Program or erase operation is complete and inactive
bit 14
WREN: Write Enable bit
1 = Enable Flash program/erase operations
0 = Inhibit Flash program/erase operations
bit 13
WRERR: Write Sequence Error Flag bit
1 = An improper program or erase sequence attempt or termination has occurred (bit is set
automatically on any set attempt of the WR bit)
0 = The program or erase operation completed normally
bit 12
NVMSIDL: NVM Stop-in-Idle Control bit(2)
1 = Flash voltage regulator goes into Stand-by mode during Idle mode
0 = Flash voltage regulator is active during Idle mode
bit 11-4
Unimplemented: Read as ‘0’
bit 3-0
NVMOP<3:0>: NVM Operation Select bits(3,4)
1111 = Reserved
1110 = Reserved
1101 = Reserved
1100 = Reserved
1011 = Reserved
1010 = Reserved
0011 = Memory page erase operation
0010 = Reserved
0001 = Memory double-word program operation(5)
0000 = Reserved
Note 1:
2:
3:
4:
5:
These bits can only be reset on POR.
If this bit is set, there will be minimal power savings (IIDLE), and upon exiting Idle mode there is a delay
(TVREG) before Flash memory becomes operational.
All other combinations of NVMOP<3:0> are unimplemented.
Execution of the PWRSAV instruction is ignored while any of the NVM operations are in progress.
Two adjacent words on a 4-word boundary are programmed during execution of this operation.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 119
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 5-2:
U-0
—
bit 15
NVMADRU: NONVOLATILE MEMORY UPPER ADDRESS REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
NVMADRU<7:0>
R/W-x
R/W-x
R/W-x
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
NVMADRU<7:0>: Non-volatile Memory Upper Write Address bits
Selects the upper 8 bits of the location to program or erase in program Flash memory. This register
may be read or written by the user application.
REGISTER 5-3:
R/W-x
NVMADR: NONVOLATILE MEMORY LOWER ADDRESS REGISTER
R/W-x
R/W-x
R/W-x
R/W-x
NVMADR<15:8>
R/W-x
R/W-x
R/W-x
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
NVMADR<7:0>
R/W-x
R/W-x
R/W-x
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
NVMADR<15:0>: Non-volatile Memory Lower Write Address bits
Selects the lower 16 bits of the location to program or erase in program Flash memory. This register
may be read or written by the user application.
REGISTER 5-4:
NVMKEY: NONVOLATILE MEMORY KEY REGISTER
U-0
—
bit 15
U-0
—
W-0
W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
W-0
W-0
W-0
NVMKEY<7:0>
W-0
W-0
bit 7
W-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
U-0
—
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
NVMKEY<7:0>: Key Register (write-only) bits
DS70657E-page 120
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
6.0
RESETS
A simplified block diagram of the Reset module is
shown in Figure 6-1.
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 8. “Reset”
(DS70602) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
Any active source of Reset will make the SYSRST signal active. On system Reset, some of the registers
associated with the CPU and peripherals are forced to
a known Reset state and some are unaffected.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
A POR clears all the bits, except for the POR and BOR
bits (RCON<1:0>), that are set. The user application
can set or clear any bit at any time during code
execution. The RCON bits only serve as status bits.
Setting a particular Reset status bit in software does
not cause a device Reset to occur.
The Reset module combines all reset sources and
controls the device Master Reset Signal, SYSRST. The
following is a list of device Reset sources:
•
•
•
•
•
•
•
•
POR: Power-on Reset
BOR: Brown-out Reset
MCLR: Master Clear Pin Reset
SWR: RESET Instruction
WDTO: Watchdog Timer Reset
CM: Configuration Mismatch Reset
TRAPR: Trap Conflict Reset
IOPUWR: Illegal Condition Device Reset
- Illegal Opcode Reset
- Uninitialized W Register Reset
- Security Reset
FIGURE 6-1:
Note:
Refer to the specific peripheral section or
Section 4.0 “Memory Organization” of
this manual for register Reset states.
All types of device Reset sets a corresponding status
bit in the RCON register to indicate the type of Reset
(see Register 6-1).
The RCON register also has other bits associated with
the Watchdog Timer and device power-saving states.
The function of these bits is discussed in other sections
of this manual.
Note:
The status bits in the RCON register
should be cleared after they are read so
that the next RCON register value after a
device Reset is meaningful.
There are two types of Reset, a cold Reset and a warm
Reset. A cold Reset is the result of a POR or BOR and
the FNOSC Configuration bits in the FOSC device
Configuration register select the device clock source. A
warm Reset is the result of all other Resets including
the RESET instruction and the Current Oscillator Selection bits (COSC<2:0>) in the Oscillator Control register
(OSCCON<14:12>) select the clock source.
RESET SYSTEM BLOCK DIAGRAM
RESET Instruction
Glitch Filter
MCLR
WDT
Module
Sleep or Idle
VDD
BOR
Internal
Regulator
SYSRST
VDD Rise
Detect
POR
Trap Conflict
Illegal Opcode
Uninitialized W Register
Security Reset
Configuration Mismatch
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 121
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
6.1
Reset Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
6.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 8. “Reset” (DS70602)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
DS70657E-page 122
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
RCON: RESET CONTROL REGISTER(1)
REGISTER 6-1:
R/W-0
R/W-0
U-0
U-0
R/W-0
U-0
R/W-0
R/W-0
TRAPR
IOPUWR
—
—
VREGSF
—
CM
VREGS
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
EXTR
SWR
SWDTEN(2)
WDTO
SLEEP
IDLE
BOR
POR
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
bit 14
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
Address Pointer caused a Reset
0 = An illegal opcode or uninitialized W Reset has not occurred
bit 13-12
Unimplemented: Read as ‘0’
bit 11
VREGSF: Flash Voltage Regulator Standby During Sleep bit
1 = Flash Voltage regulator is active during Sleep
0 = Flash Voltage regulator goes into Standby mode during Sleep
bit 10
Unimplemented: Read as ‘0’
bit 9
CM: Configuration Mismatch Flag bit
1 = A configuration mismatch Reset has occurred.
0 = A configuration mismatch Reset has NOT occurred
bit 8
VREGS: Voltage Regulator Standby During Sleep bit
1 = Voltage regulator is active during Sleep
0 = Voltage regulator goes into Standby mode during Sleep
bit 7
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
bit 6
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
bit 5
SWDTEN: Software Enable/Disable of WDT bit(2)
1 = WDT is enabled
0 = WDT is disabled
bit 4
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
Note 1:
2:
All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 123
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 6-1:
RCON: RESET CONTROL REGISTER(1) (CONTINUED)
bit 3
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
bit 2
IDLE: Wake-up from Idle Flag bit
1 = Device was in Idle mode
0 = Device was not in Idle mode
bit 1
BOR: Brown-out Reset Flag bit
1 = A Brown-out Reset has occurred
0 = A Brown-out Reset has not occurred
bit 0
POR: Power-on Reset Flag bit
1 = A Power-on Reset has occurred
0 = A Power-on Reset has not occurred
Note 1:
2:
All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
DS70657E-page 124
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
7.0
INTERRUPT CONTROLLER
7.1
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet,
refer to Section 6. “Interrupts”
(DS70600) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X interrupt controller
reduces the numerous peripheral interrupt request signals to a single interrupt request signal to the
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X CPU.
The interrupt controller has the following features:
• Up to eight processor exceptions and software
traps
• Eight user-selectable priority levels
• Interrupt Vector Table (IVT) with a unique vector
for each interrupt or exception source
• Fixed priority within a specified user priority level
• Fixed interrupt entry and return latencies
© 2011-2012 Microchip Technology Inc.
Interrupt Vector Table
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X Interrupt Vector
Table (IVT), shown in Figure 7-1, resides in program
memory, starting at location 000004h. The IVT contains
seven non-maskable trap vectors and up to 114
sources of interrupt. In general, each interrupt source
has its own vector. Each interrupt vector contains a 24bit-wide address. The value programmed into each
interrupt vector location is the starting address of the
associated Interrupt Service Routine (ISR).
Interrupt vectors are prioritized in terms of their natural
priority. This priority is linked to their position in the
vector table. Lower addresses generally have a higher
natural priority. For example, the interrupt associated
with vector 0 takes priority over interrupts at any other
vector address.
7.2
Reset Sequence
A device Reset is not a true exception because the
interrupt controller is not involved in the Reset process.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices clear their
registers in response to a Reset, which forces the PC
to zero. The device then begins program execution at
location 0x000000. A GOTO instruction at the Reset
address can redirect program execution to the
appropriate start-up routine.
Note:
Preliminary
Any unimplemented or unused vector
locations in the IVT should be
programmed with the address of a default
interrupt handler routine that contains a
RESET instruction.
DS70657E-page 125
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
INTERRUPT VECTOR TABLE
IVT
Decreasing Natural Order Priority
FIGURE 7-1:
DS70657E-page 126
Reset – GOTO Instruction
Reset – GOTO Address
Oscillator Fail Trap Vector
Address Error Trap Vector
Generic Hard Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
DMAC Error Trap Vector
Generic Soft Trap Vector
Reserved
Interrupt Vector 0
Interrupt Vector 1
:
:
:
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
:
:
:
Interrupt Vector 116
Interrupt Vector 117
Interrupt Vector 118
Interrupt Vector 119
Interrupt Vector 120
:
:
:
Interrupt Vector 244
Interrupt Vector 245
START OF CODE
0x000000
0x000002
0x000004
0x000006
0x000008
0x00000A
0x00000C
0x00000E
0x000010
0x000012
0x000014
0x000016
:
:
:
0x00007C
0x00007E
0x000080
:
:
:
0x0000FC
0x0000FE
0x000100
0x000102
0x000104
:
:
:
0x0001FC
0x0001FE
0x000200
Preliminary
See Table 7-1 for
Interrupt Vector details
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 7-1:
INTERRUPT VECTOR DETAILS
Interrupt Source
Vector
#
IRQ
#
IVT Address
Interrupt Bit Location
Flag
Enable
Priority
Highest Natural Order Priority
INT0 – External Interrupt 0
8
0
0x000014
IFS0<0>
IEC0<0>
IPC0<2:0>
IC1 – Input Capture 1
9
1
0x000016
IFS0<1>
IEC0<1>
IPC0<6:4>
OC1 – Output Compare 1
10
2
0x000018
IFS0<2>
IEC0<2>
IPC0<10:8>
T1 – Timer1
11
3
0x00001A
IFS0<3>
IEC0<3>
IPC0<14:12>
DMA0 – DMA Channel 0
12
4
0x00001C
IFS0<4>
IEC0<4>
IPC1<2:0>
IC2 – Input Capture 2
13
5
0x00001E
IFS0<5>
IEC0<5>
IPC1<6:4>
OC2 – Output Compare 2
14
6
0x000020
IFS0<6>
IEC0<6>
IPC1<10:8>
T2 – Timer2
15
7
0x000022
IFS0<7>
IEC0<7>
IPC1<14:12>
T3 – Timer3
16
8
0x000024
IFS0<8>
IEC0<8>
IPC2<2:0>
SPI1E – SPI1 Error
17
9
0x000026
IFS0<9>
IEC0<9>
IPC2<6:4>
SPI1 – SPI1 Transfer Done
18
10
0x000028
IFS0<10> IEC0<10>
IPC2<10:8>
U1RX – UART1 Receiver
19
11
0x00002A
IFS0<11> IEC0<11> IPC2<14:12>
U1TX – UART1 Transmitter
20
12
0x00002C
IFS0<12> IEC0<12>
IPC3<2:0>
AD1 – ADC1 Convert Done
21
13
0x00002E
IFS0<13> IEC0<13>
IPC3<6:4>
IFS0<14> IEC0<14>
IPC3<10:8>
DMA1 – DMA Channel 1
22
14
0x000030
Reserved
23
15
0x000032
—
—
—
SI2C1 – I2C1 Slave Event
24
16
0x000034
IFS1<0>
IEC1<0>
IPC4<2:0>
MI2C1 – I2C1 Master Event
25
17
0x000036
IFS1<1>
IEC1<1>
IPC4<6:4>
CM – Comparator Combined Event
26
18
0x000038
IFS1<2>
IEC1<2>
IPC4<10:8>
CN – Input Change Interrupt
27
19
0x00003A
IFS1<3>
IEC1<3>
IPC4<14:12>
INT1 – External Interrupt 1
28
20
0x00003C
IFS1<4>
IEC1<4>
IPC5<2:0>
29-31
21-23
0x00003E-0x000042
—
—
—
DMA2 – DMA Channel 2
32
24
0x000044
IFS1<8>
IEC1<8>
IPC6<2:0>
OC3 – Output Compare 3
33
25
0x000046
IFS1<9>
IEC1<9>
IPC6<6:4>
OC4 – Output Compare 4
34
26
0x000048
IFS1<10> IEC1<10>
IPC6<10:8>
T4 – Timer4
35
27
0x00004A
IFS1<11> IEC1<11> IPC6<14:12>
T5 – Timer5
36
28
0x00004C
IFS1<12> IEC1<12>
INT2 – External Interrupt 2
37
29
0x00004E
IFS1<13> IEC1<13>
IPC7<6:4>
U2RX – UART2 Receiver
38
30
0x000050
IFS1<14> IEC1<14>
IPC7<10:8>
U2TX – UART2 Transmitter
39
31
0x000052
IFS1<15> IEC1<15> IPC7<14:12>
SPI2E – SPI2 Error
40
32
0x000054
IFS2<0>
IEC2<0>
SPI2 – SPI2 Transfer Done
41
33
0x000056
IFS2<1>
IEC2<1>
IPC8<6:4>
C1RX – CAN1 RX Data Ready(1)
42
34
0x000058
IFS2<2>
IEC2<2>
IPC8<10:8>
C1 – CAN1 Event(1)
43
35
0x00005A
IFS2<3>
IEC2<3>
IPC8<14:12>
DMA3 – DMA Channel 3
44
36
0x00005C
IFS2<4>
IEC2<4>
IPC9<2:0>
IC3 – Input Capture 3
45
37
0x00005E
IFS2<5>
IEC2<5>
IPC9<6:4>
IC4 – Input Capture 4
46
38
0x000060
IFS2<6>
IEC2<6>
IPC9<10:8>
47-56
39-48
0x000062-0x000074
—
—
—
SI2C2 – I2C2 Slave Event
57
49
0x000076
IFS3<1>
IEC3<1>
IPC12<6:4>
MI2C2 – I2C2 Master Event
58
50
0x000078
IFS3<2>
IEC3<2>
IPC12<10:8>
Reserved
Reserved
Reserved
IPC7<2:0>
IPC8<2:0>
59-64
51-56
0x00007A-0x000084
—
—
—
PSEM – PWM Special Event Match(2)
65
57
0x000086
IFS3<9>
IEC3<9>
IPC14<6:4>
QEI1 – QEI1 Position Counter Compare(2)
66
58
0x000088
IFS3<10> IEC3<10> IPC14<10:8>
Note 1:
2:
This interrupt source is available on dsPIC33EPXXXGP50X and dsPIC33EPXXXMC50X devices only.
This interrupt source is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 127
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 7-1:
INTERRUPT VECTOR DETAILS (CONTINUED)
Interrupt Source
Reserved
U1E – UART1 Error Interrupt
Interrupt Bit Location
Vector
#
IRQ
#
IVT Address
67-72
59-64
0x00008A-0x000094
—
—
—
73
65
0x000096
IFS4<1>
IEC4<1>
IPC16<6:4>
IPC16<10:8>
Flag
Enable
Priority
U2E – UART2 Error Interrupt
74
66
0x000098
IFS4<2>
IEC4<2>
CRC – CRC Generator Interrupt
75
67
0x00009A
IFS4<3>
IEC4<3> IPC16<14:12>
76-77
68-69
0x00009C-0x00009E
—
—
—
78
70
0x000A0
IFS4<6>
IEC4<6>
IPC17<10:8>
79-84
71-76
0x0000A2 -0x0000AC
—
—
85
77
0x0000AE
Reserved
C1TX – CAN1 TX Data Request(1)
Reserved
CTMU – CTMU Interrupt
Reserved
IFS4<13> IEC4<13>
86-101
78-93
0x0000B0-0x0000CE
PWM1 – PWM Generator 1(2)
102
94
0x0000D0
IFS5<14> IEC5<14> IPC23<10:8>
PWM2 – PWM Generator 2(2)
103
95
0x0000D2
IFS5<15> IEC5<15> IPC23<14:12>
PWM3 – PWM Generator 3(2)
104
96
0x0000D4
IFS6<0>
IEC6<0>
IPC24<2:0>
—
—
—
Reserved
105-149 97-141 0x0001D6 -0x00012E
ICD – ICD Application
150
142
—
—
—
IPC19<6:4>
—
0x000142
IFS8<14> IEC8<14> IPC35<10:8>
IFS8<15> IEC8<15> IPC35<14:12>
JTAG – JTAG Programming
151
143
0x000130
Reserved
152
144
0x000134
—
—
—
PTGSTEP – PTG Step
153
145
0x000136
IFS9<1>
IEC9<1>
IPC36<6:4>
PTGWDT – PTG Watchdog Time-out
154
146
0x000138
IFS9<2>
IEC9<2>
IPC36<10:8>
PTG0 – PTG Interrupt 0
155
147
0x00013A
IFS9<3>
IEC9<3> IPC36<14:12>
PTG1 – PTG Interrupt 1
156
148
0x00013C
IFS9<4>
IEC9<4>
PTG2 – PTG Interrupt 2
157
149
0x00013E
IFS9<5>
IEC9<5>
IPC37<6:4>
PTG3 – PTG Interrupt 3
158
150
0x000140
IFS9<6>
IEC9<6>
IPC37<10:8>
—
—
—
Reserved
159-245 151-245 0x000142- 0x0001FE
IPC37<2:0>
Lowest Natural Order Priority
Note 1:
2:
This interrupt source is available on dsPIC33EPXXXGP50X and dsPIC33EPXXXMC50X devices only.
This interrupt source is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
DS70657E-page 128
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
7.3
Interrupt Resources
7.4.2
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
7.3.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
Section 6. “Interrupts” (DS70600)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
IECx
The IEC registers maintain all of the interrupt enable
bits. These control bits are used to individually enable
interrupts from the peripherals or external signals.
7.4.4
IPCx
INTTREG
The INTTREG register contains the associated
interrupt vector number and the new CPU interrupt
priority level, which are latched into vector number
(VECNUM<7:0>) and Interrupt level bit (ILR<3:0>)
fields in the INTTREG register. The new interrupt
priority level is the priority of the pending interrupt.
Interrupt Control and Status
Registers
INTCON1
INTCON2
INTCON3
INTCON4
INTTREG
7.4.1
7.4.3
7.4.5
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices implement the
following registers for the interrupt controller:
•
•
•
•
•
The IFS registers maintain all of the interrupt request
flags. Each source of interrupt has a status bit, which is
set by the respective peripherals or external signal and
is cleared via software.
The IPC registers are used to set the interrupt priority
level for each source of interrupt. Each user interrupt
source can be assigned to one of eight priority levels.
KEY RESOURCES
•
•
•
•
•
•
7.4
IFSx
The interrupt sources are assigned to the IFSx, IECx
and IPCx registers in the same sequence as they are
listed in Table 7-1. For example, the INT0 (External
Interrupt 0) is shown as having vector number 8 and a
natural order priority of 0. Thus, the INT0IF bit is found
in IFS0<0>, the INT0IE bit in IEC0<0> and the INT0IP
bits in the first position of IPC0 (IPC0<2:0>).
7.4.6
INTCON1 THROUGH INTCON4
Global interrupt control functions are controlled from
INTCON1, INTCON2, INTCON3 and INTCON4.
STATUS/CONTROL REGISTERS
Although these registers are not specifically part of the
interrupt control hardware, two of the CPU Control
registers contain bits that control interrupt functionality.
For more information on these registers refer to
Section 2. “CPU” (DS70359) in the “dsPIC33E/
PIC24E Family Reference Manual”.
INTCON3 contains the status flags for the DMA, and
DO stack overflow status trap sources.
• The CPU STATUS register, SR, contains the
IPL<2:0> bits (SR<7:5>). These bits indicate the
current CPU interrupt priority level. The user
software can change the current CPU priority
level by writing to the IPL bits.
• The CORCON register contains the IPL3 bit
which, together with IPL<2:0>, also indicates the
current CPU priority level. IPL3 is a read-only bit
so that trap events cannot be masked by the user
software.
The INTCON4 register contains the
generated hard trap status bit (SGHT).
All Interrupt registers are described in Register 7-3
through Register 7-7 in the following pages.
INTCON1 contains the Interrupt Nesting Disable bit
(NSTDIS) as well as the control and status flags for the
processor trap sources.
The INTCON2 register controls external interrupt
request signal behavior and also contains the General
Interrupt Enable bit (GIE).
© 2011-2012 Microchip Technology Inc.
software
Preliminary
DS70657E-page 129
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
SR: CPU STATUS REGISTER(1)
REGISTER 7-1:
R/W-0
R/W-0
R/W-0
R/W-0
R/C-0
R/C-0
R -0
R/W-0
OA
OB
SA
SB
OAB
SAB
DA
DC
bit 15
bit 8
R/W-0(3)
R/W-0(3)
R/W-0(3)
IPL<2:0>(2)
R-0
R/W-0
R/W-0
R/W-0
R/W-0
RA
N
OV
Z
C
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
C = Clearable bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3)
111 = CPU Interrupt Priority Level is 7 (15). User interrupts disabled
110 = CPU Interrupt Priority Level is 6 (14)
101 = CPU Interrupt Priority Level is 5 (13)
100 = CPU Interrupt Priority Level is 4 (12)
011 = CPU Interrupt Priority Level is 3 (11)
010 = CPU Interrupt Priority Level is 2 (10)
001 = CPU Interrupt Priority Level is 1 (9)
000 = CPU Interrupt Priority Level is 0 (8)
bit 7-5
Note 1:
2:
3:
For complete register details, see Register 3-1.
The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the IPL, if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
The IPL<2:0> Status bits are read-only when the NSTDIS bit (INTCON1<15>) = 1.
DS70657E-page 130
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 7-2:
CORCON: CORE CONTROL REGISTER(1)
R/W-0
U-0
VAR
—
R/W-0
R/W-0
US<1:0>
R/W-0
R-0
EDT
R-0
R-0
DL<2:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-1
R/W-0
R/C-0
R-0
R/W-0
R/W-0
SATA
SATB
SATDW
ACCSAT
IPL3(2)
SFA
RND
IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
VAR: Variable Exception Processing Latency Control bit
1 = Variable exception processing enabled
0 = Fixed exception processing enabled
bit 3
IPL3: CPU Interrupt Priority Level Status bit 3(2)
1 = CPU interrupt priority level is greater than 7
0 = CPU interrupt priority level is 7 or less
Note 1:
2:
x = Bit is unknown
For complete register details, see Register 3-2.
The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 131
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 7-3:
INTCON1: INTERRUPT CONTROL REGISTER 1
R/W-0
R/W-0
NSTDIS
OVAERR(1)
R/W-0
R/W-0
R/W-0
OVBERR(1) COVAERR(1) COVBERR(1)
R/W-0
R/W-0
R/W-0
OVATE(1)
OVBTE(1)
COVTE(1)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
SFTACERR(1)
DIV0ERR
DMACERR
MATHERR
ADDRERR
STKERR
OSCFAIL
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
NSTDIS: Interrupt Nesting Disable bit
1 = Interrupt nesting is disabled
0 = Interrupt nesting is enabled
bit 14
OVAERR: Accumulator A Overflow Trap Flag bit(1)
1 = Trap was caused by overflow of Accumulator A
0 = Trap was not caused by overflow of Accumulator A
bit 13
OVBERR: Accumulator B Overflow Trap Flag bit(1)
1 = Trap was caused by overflow of Accumulator B
0 = Trap was not caused by overflow of Accumulator B
bit 12
COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit(1)
1 = Trap was caused by catastrophic overflow of Accumulator A
0 = Trap was not caused by catastrophic overflow of Accumulator A
bit 11
COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit(1)
1 = Trap was caused by catastrophic overflow of Accumulator B
0 = Trap was not caused by catastrophic overflow of Accumulator B
bit 10
OVATE: Accumulator A Overflow Trap Enable bit(1)
1 = Trap overflow of Accumulator A
0 = Trap is disabled
bit 9
OVBTE: Accumulator B Overflow Trap Enable bit(1)
1 = Trap overflow of Accumulator B
0 = Trap is disabled
bit 8
COVTE: Catastrophic Overflow Trap Enable bit(1)
1 = Trap on catastrophic overflow of Accumulator A or B enabled
0 = Trap is disabled
bit 7
SFTACERR: Shift Accumulator Error Status bit(1)
1 = Math error trap was caused by an invalid accumulator shift
0 = Math error trap was not caused by an invalid accumulator shift
bit 6
DIV0ERR: Divide-by-zero Error Status bit
1 = Math error trap was caused by a divide by zero
0 = Math error trap was not caused by a divide by zero
bit 5
DMACERR: DMAC Trap Flag bit
1 = DMAC trap has occurred
0 = DMAC trap has not occurred
bit 4
MATHERR: Math Error Status bit
1 = Math error trap has occurred
0 = Math error trap has not occurred
Note 1:
This bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
DS70657E-page 132
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 7-3:
INTCON1: INTERRUPT CONTROL REGISTER 1 (CONTINUED)
bit 3
ADDRERR: Address Error Trap Status bit
1 = Address error trap has occurred
0 = Address error trap has not occurred
bit 2
STKERR: Stack Error Trap Status bit
1 = Stack error trap has occurred
0 = Stack error trap has not occurred
bit 1
OSCFAIL: Oscillator Failure Trap Status bit
1 = Oscillator failure trap has occurred
0 = Oscillator failure trap has not occurred
bit 0
Unimplemented: Read as ‘0’
Note 1:
This bit is available on dsPIC33EPXXXMC20X/50X and dsPIC33EPXXXGP50X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 133
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 7-4:
INTCON2: INTERRUPT CONTROL REGISTER 2
R/W-1
R/W-0
R/W-0
U-0
U-0
U-0
U-0
U-0
GIE
DISI
SWTRAP
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
—
—
—
—
—
INT2EP
INT1EP
INT0EP
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
GIE: Global Interrupt Enable bit
1 = Interrupts and Associated IE bits are enabled
0 = Interrupts are disabled, but traps are still enabled
bit 14
DISI: DISI Instruction Status bit
1 = DISI instruction is active
0 = DISI instruction is not active
bit 13
SWTRAP: Software Trap Status bit
1 = Software trap is enabled
0 = Software trap is disabled
bit 12-3
Unimplemented: Read as ‘0’
bit 2
INT2EP: External Interrupt 2 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
bit 1
INT1EP: External Interrupt 1 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
bit 0
INT0EP: External Interrupt 0 Edge Detect Polarity Select bit
1 = Interrupt on negative edge
0 = Interrupt on positive edge
DS70657E-page 134
Preliminary
x = Bit is unknown
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 7-5:
INTCON3: INTERRUPT CONTROL REGISTER 3
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
—
—
DAE
DOOVR
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-6
Unimplemented: Read as ‘0’
bit 5
DAE: DMA Address Error Soft Trap Status bit
1 = DMA Address error soft trap has occurred
0 = DMA Address error soft trap has not occurred
bit 4
DOOVR: Do Stack Overflow Soft Trap Status bit
1 = Do stack overflow soft trap has occurred
0 = Do stack overflow soft trap has not occurred
bit 3-0
Unimplemented: Read as ‘0’
REGISTER 7-6:
x = Bit is unknown
INTCON4: INTERRUPT CONTROL REGISTER 4
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
SGHT
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-1
Unimplemented: Read as ‘0’
bit 0
SGHT: Software Generated Hard Trap Status bit
1 = Software generated hard trap has occurred
0 = Software generated hard trap has not occurred
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 135
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 7-7:
INTTREG: INTERRUPT CONTROL AND STATUS REGISTER
U-0
U-0
U-0
U-0
—
—
—
—
R-0
R-0
R-0
R-0
ILR<3:0>
bit 15
bit 8
U-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
VECNUM<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11-8
ILR<3:0>: New CPU Interrupt Priority Level bits
1111 = CPU Interrupt Priority Level is 15
•
•
•
0001 = CPU Interrupt Priority Level is 1
0000 = CPU Interrupt Priority Level is 0
bit 7-0
VECNUM<7:0>: Vector Number of Pending Interrupt bits
11111111 = 255, Reserved; do not use
•
•
•
00001001 = 9, IC1 – Input Capture 1
00001000 = 8, INT0 – External Interrupt 0
00000111 = 7, Reserved; do not use
00000110 = 6, Generic Soft Error Trap
00000101 = 5, DMAC Error Trap
00000100 = 4, Math Error Trap
00000011 = 3, Stack Error Trap
00000010 = 2, Generic Hard Trap
00000001 = 1, Address Error Trap
00000000 = 0, Oscillator Fail Trap
DS70657E-page 136
Preliminary
x = Bit is unknown
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
8.0
DIRECT MEMORY ACCESS
(DMA)
The DMA controller transfers data between peripheral
data registers and data space SRAM
In addition, DMA can access the entire data memory
space. The Data Memory Bus Arbiter is utilized when
either the CPU or DMA attempt to access SRAM,
resulting in potential DMA or CPU stalls.
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 22. “Direct Memory Access (DMA)” (DS70348) of the
“dsPIC33E/PIC24E Family Reference
Manual”, which is available from the
Microchip
web
site
(www.microchip.com).
The DMA controller supports 4 independent channels.
Each channel can be configured for transfers to or from
selected peripherals. Some of the peripherals
supported by the DMA controller include:
•
•
•
•
•
•
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 8-1:
ECAN™
Analog-to-Digital Converter (ADC)
Serial Peripheral Interface (SPI)
UART
Input Capture
Output Compare
Refer to Table 8-1 for a complete list of supported
peripherals.
DMA CONTROLLER
PERIPHERAL
DMA
Data Memory
Arbiter
(see Figure 4-18)
SRAM
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 137
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
In addition, DMA transfers can be triggered by Timers
as well as external interrupts. Each DMA channel is
unidirectional. Two DMA channels must be allocated to
read and write to a peripheral. If more than one channel
receive a request to transfer data, a simple fixed priority
scheme, based on channel number, dictates which
channel completes the transfer and which channel, or
channels, are left pending. Each DMA channel moves
a block of data, after which it generates an interrupt to
the CPU to indicate that the block is available for
processing.
The DMA controller
capabilities:
provides
these
functional
• Four DMA channels
• Register Indirect With Post-increment Addressing
mode
• Register Indirect Without Post-increment
Addressing mode
TABLE 8-1:
• Peripheral Indirect Addressing mode (peripheral
generates destination address)
• CPU interrupt after half or full-block transfer complete
• Byte or word transfers
• Fixed priority channel arbitration
• Manual (software) or Automatic (peripheral DMA
requests) transfer initiation
• One-Shot or Auto-Repeat block transfer modes
• Ping-Pong mode (automatic switch between two
SRAM start addresses after each block transfer
complete)
• DMA request for each channel can be selected
from any supported interrupt source
• Debug support features
The peripherals that can utilize DMA are listed in
Table 8-1.
DMA CHANNEL TO PERIPHERAL ASSOCIATIONS
DMAxREQ Register
IRQSEL<7:0> Bits
DMAxPAD Register
(Values to Read from
Peripheral)
DMAxPAD Register
(Values to Write to
Peripheral)
INT0 – External Interrupt 0
IC1 – Input Capture 1
IC2 – Input Capture 2
IC3 – Input Capture 3
IC4 – Input Capture 4
OC1 – Output Compare 1
00000000
00000001
00000101
00100101
00100110
00000010
—
0x0144 (IC1BUF)
0x014C (IC2BUF)
0x0154 (IC3BUF)
0x015C (IC4BUF)
—
OC2 – Output Compare 2
00000110
—
OC3 – Output Compare 3
00011001
—
OC4 – Output Compare 4
00011010
—
TMR2 – Timer2
TMR3 – Timer3
TMR4 – Timer4
TMR5 – Timer5
SPI1 Transfer Done
SPI2 Transfer Done
UART1RX – UART1 Receiver
UART1TX – UART1 Transmitter
UART2RX – UART2 Receiver
UART2TX – UART2 Transmitter
ECAN1 – RX Data Ready
ECAN1 – TX Data Request
ADC1 – ADC1 Convert Done
00000111
00001000
00011011
00011100
00001010
00100001
00001011
00001100
00011110
00011111
00100010
01000110
00001101
—
—
—
—
0x0248 (SPI1BUF)
0x0268 (SPI2BUF)
0x0226 (U1RXREG)
—
0x0236 (U2RXREG)
—
0x0440 (C1RXD)
—
0x0300 (ADC1BUF0)
—
—
—
—
—
0x0906 (OC1R)
0x0904 (OC1RS)
0x0910 (OC2R)
0x090E (OC2RS)
0x091A (OC3R)
0x0918 (OC3RS)
0x0924 (OC4R)
0x0922 (OC4RS)
—
—
—
—
0x0248 (SPI1BUF)
0x0268 (SPI2BUF)
—
0x0224 (U1TXREG)
—
0x0234 (U2TXREG)
—
0x0442 (C1TXD)
—
Peripheral to DMA Association
DS70657E-page 138
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 8-2:
DMA CONTROLLER BLOCK DIAGRAM
SRAM
Peripheral Indirect Address
Arbiter
DMA
Control
DMA Controller
DMA
Ready
Peripheral 1
DMA
Channels
0 1
2
3
CPU
DMA
IRQ to DMA
and Interrupt
Controller
Modules
DMA X-Bus
CPU Peripheral X-Bus
CPU
Peripheral
Note: CPU and DMA address buses are not shown
for clarity.
8.1
DMA Resources
8.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 22. “Direct Memory Access (DMA)”
(DS70348)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
IRQ to DMA and
Interrupt Controller
Modules
8.2
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
CPU DMA
DMA
Ready
Peripheral 2
Non-DMA
CPU DMA
DMA
Ready
Peripheral 3
IRQ to DMA and
Interrupt Controller
Modules
DMAC Registers
Each DMAC Channel x (where x = 0 through 3)
contains the following registers:
• 16-bit DMA Channel Control register (DMAxCON)
• 16-bit DMA Channel IRQ Select register
(DMAxREQ)
• 32-bit DMA RAM Primary Start Address register
(DMAxSTA)
• 32-bit DMA RAM Secondary Start Address
register (DMAxSTB)
• 16-bit DMA Peripheral Address register (DMAxPAD)
• 14-bit DMA Transfer Count register (DMAxCNT)
Additional status registers (DMAPWC, DMARQC,
DMAPPS, DMALCA, and DSADR) are common to all
DMAC channels. These status registers provide information on write and request collisions, as well as on
last address and channel access information.
The interrupt flags (DMAxIF) are located in an IFSx
register in the interrupt controller. The corresponding
interrupt enable control bits (DMAxIE) are located in
an IECx register in the interrupt controller, and the
corresponding interrupt priority control bits (DMAxIP)
are located in an IPCx register in the interrupt
controller.
Preliminary
DS70657E-page 139
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-1:
R/W-0
CHEN
bit 15
DMAXCON: DMA CHANNEL X CONTROL REGISTER
R/W-0
SIZE
R/W-0
DIR
R/W-0
HALF
R/W-0
NULLW
U-0
—
R/W-0
R/W-0
AMODE<1:0>
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 14
bit 13
bit 12
bit 11
bit 10-6
bit 5-4
bit 3-2
bit 1-0
U-0
—
U-0
—
bit 8
U-0
—
bit 15
U-0
—
W = Writable bit
‘1’ = Bit is set
U-0
—
R/W-0
R/W-0
MODE<1:0>
bit 0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
CHEN: Channel Enable bit
1 = Channel enabled
0 = Channel disabled
SIZE: Data Transfer Size bit
1 = Byte
0 = Word
DIR: Transfer Direction bit (source/destination bus select)
1 = Read from RAM address, write to peripheral address
0 = Read from Peripheral address, write to RAM address
HALF: Block Transfer Interrupt Select bit
1 = Initiate interrupt when half of the data has been moved
0 = Initiate interrupt when all of the data has been moved
NULLW: Null Data Peripheral Write Mode Select bit
1 = Null data write to peripheral in addition to RAM write (DIR bit must also be clear)
0 = Normal operation
Unimplemented: Read as ‘0’
AMODE<1:0>: DMA Channel Addressing Mode Select bits
11 = Reserved
10 = Peripheral Indirect Addressing mode
01 = Register Indirect without Post-Increment mode
00 = Register Indirect with Post-Increment mode
Unimplemented: Read as ‘0’
MODE<1:0>: DMA Channel Operating Mode Select bits
11 = One-Shot, Ping-Pong modes enabled (one block transfer from/to each DMA buffer)
10 = Continuous, Ping-Pong modes enabled
01 = One-Shot, Ping-Pong modes disabled
00 = Continuous, Ping-Pong modes disabled
DS70657E-page 140
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-2:
R/S-0
FORCE(1)
bit 15
DMAXREQ: DMA CHANNEL X IRQ SELECT REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQSEL<7:0>
R/W-0
R/W-0
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-8
bit 7-0
Note 1:
2:
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
FORCE: Force DMA Transfer bit(1)
1 = Force a single DMA transfer (Manual mode)
0 = Automatic DMA transfer initiation by DMA Request
Unimplemented: Read as ‘0’
IRQSEL<7:0>: DMA Peripheral IRQ Number Select bits
01000110 = ECAN1 – TX Data Request(2)
00100110 = IC4 – Input Capture 4
00100101 = IC3 – Input Capture 3
00100010 = ECAN1 – RX Data Ready(2)
00100001 = SPI2 Transfer Done
00011111 = UART2TX – UART2 Transmitter
00011110 = UART2RX – UART2 Receiver
00011100 = TMR5 – Timer5
00011011 = TMR4 – Timer4
00011010 = OC4 – Output Compare 4
00011001 = OC3 – Output Compare 3
00001101 = ADC1 – ADC1 Convert done
00001100 = UART1TX – UART1 Transmitter
00001011 = UART1RX – UART1 Receiver
00001010 = SPI1 – Transfer Done
00001000 = TMR3 – Timer3
00000111 = TMR2 – Timer2
00000110 = OC2 – Output Compare 2
00000101 = IC2 – Input Capture 2
00000010 = OC1 – Output Compare 1
00000001 = IC1 – Input Capture 1
00000000 = INT0 – External Interrupt 0
The FORCE bit cannot be cleared by user software. The FORCE bit is cleared by hardware when the
forced DMA transfer is complete or the channel is disabled (CHEN = 0).
This selection is available in dsPIC33EPXXXGP/MC50X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 141
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-3:
DMAXSTAH: DMA CHANNEL X START ADDRESS REGISTER A (HIGH)
U-0
U-0
U-0
U-0
R/W-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STA<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7-0
STA<23:16>: Primary Start Address bits (source or destination)
REGISTER 8-4:
R/W-0
DMAXSTAL: DMA CHANNEL X START ADDRESS REGISTER A (LOW)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STA<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STA<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
STA<15:0>: Primary Start Address bits (source or destination)
DS70657E-page 142
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-5:
DMAXSTBH: DMA CHANNEL X START ADDRESS REGISTER B (HIGH)
U-0
U-0
U-0
U-0
R/W-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STB<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7-0
STB<23:16>: Secondary Start Address bits (source or destination)
REGISTER 8-6:
R/W-0
DMAXSTBL: DMA CHANNEL X START ADDRESS REGISTER B (LOW)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STB<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STB<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
STB<15:0>: Secondary Start Address bits (source or destination)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 143
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-7:
R/W-0
DMAXPAD: DMA CHANNEL X PERIPHERAL ADDRESS REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PAD<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PAD<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PAD<15:0>: Peripheral Address Register bits
If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the
DMA channel and should be avoided.
REGISTER 8-8:
DMAXCNT: DMA CHANNEL X TRANSFER COUNT REGISTER(1)
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CNT<13:8>(2)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
(2)
CNT<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-14
Unimplemented: Read as ‘0’
bit 13-0
CNT<13:0>: DMA Transfer Count Register bits(2)
Note 1:
2:
x = Bit is unknown
If the channel is enabled (i.e., active), writes to this register may result in unpredictable behavior of the
DMA channel and should be avoided.
The number of DMA transfers = CNT<13:0> + 1.
DS70657E-page 144
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-9:
DSADRH: MOST RECENT RAM HIGH ADDRESS REGISTER
U-0
U-0
U-0
U-0
R/W-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DSADR<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-8
Unimplemented: Read as ‘0’
bit 7-0
DSADR<23:16>: Most Recent DMA Address Accessed by DMA bits
REGISTER 8-10:
R-0
DSADRL: MOST RECENT RAM LOW ADDRESS REGISTER
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DSADR<15:8>
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
DSADR<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
DSADR<15:0>: Most Recent DMA Address Accessed by DMA bits
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 145
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-11:
DMAPWC: DMA PERIPHERAL WRITE COLLISION STATUS
REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R-0
R-0
R-0
R-0
—
—
—
—
PWCOL3
PWCOL2
PWCOL1
PWCOL0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3
PWCOL3: Channel 3 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 2
PWCOL2: Channel 2 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 1
PWCOL1: Channel 1 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
bit 0
PWCOL0: Channel 0 Peripheral Write Collision Flag bit
1 = Write collision detected
0 = No write collision detected
DS70657E-page 146
Preliminary
x = Bit is unknown
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-12:
DMARQC: DMA REQUEST COLLISION STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R-0
R-0
R-0
R-0
—
—
—
—
RQCOL3
RQCOL2
RQCOL1
RQCOL0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3
RQCOL3: Channel 3 Transfer Request Collision Flag bit
1 = User FORCE and Interrupt-based request collision detected
0 = No request collision detected
bit 2
RQCOL2: Channel 2 Transfer Request Collision Flag bit
1 = User FORCE and Interrupt-based request collision detected
0 = No request collision detected
bit 1
RQCOL1: Channel 1 Transfer Request Collision Flag bit
1 = User FORCE and Interrupt-based request collision detected
0 = No request collision detected
bit 0
RQCOL0: Channel 0 Transfer Request Collision Flag bit
1 = User FORCE and Interrupt-based request collision detected
0 = No request collision detected
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 147
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-13:
DMALCA: DMA LAST CHANNEL ACTIVE DMA STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
—
—
—
—
R-1
R-1
R-1
R-1
LSTCH<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3-0
LSTCH<3:0>: Last DMAC Channel Active Status bits
1111 = No DMA transfer has occurred since system Reset
1110 = Reserved
•
•
•
0100 = Reserved
0011 = Last data transfer was handled by Channel 3
0010 = Last data transfer was handled by Channel 2
0001 = Last data transfer was handled by Channel 1
0000 = Last data transfer was handled by Channel 0
DS70657E-page 148
Preliminary
x = Bit is unknown
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 8-14:
DMAPPS: DMA PING-PONG STATUS REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R-0
R-0
R-0
R-0
—
—
—
—
PPST3
PPST2
PPST1
PPST0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3
PPST3: Channel 3 Ping-Pong Mode Status Flag bit
1 = DMASTB3 register selected
0 = DMASTA3 register selected
bit 2
PPST2: Channel 2 Ping-Pong Mode Status Flag bit
1 = DMASTB2 register selected
0 = DMASTA2 register selected
bit 1
PPST1: Channel 1 Ping-Pong Mode Status Flag bit
1 = DMASTB1 register selected
0 = DMASTA1 register selected
bit 0
PPST0: Channel 0 Ping-Pong Mode Status Flag bit
1 = DMASTB0 register selected
0 = DMASTA0 register selected
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 149
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 150
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
OSCILLATOR CONFIGURATION
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X oscillator system
provides:
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet,
refer to Section 7. “Oscillator”
(DS70580) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
• On-chip Phase-Locked Loop (PLL) to boost internal operating frequency on select internal and
external oscillator sources
• On-the-fly clock switching between various clock
sources
• Doze mode for system power savings
• Fail-Safe Clock Monitor (FSCM) that detects clock
failure and permits safe application recovery or
shutdown
• Configuration bits for clock source selection
A simplified diagram of the oscillator system is shown
in Figure 9-1.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 9-1:
OSC1
OSCILLATOR SYSTEM DIAGRAM
Primary Oscillator
XT, HS, EC
POSCCLK
R(2)
S3
PLL(1)
S1
OSC2
XTPLL, HSPLL,
ECPLL, FRCPLL
FVCO(1)
DOZE<2:0>
S2
FCY(3)
DOZE
9.0
S1/S3
POSCMD<1:0>
FRC
Oscillator
FRCCLK
FRCDIV
FP(3)
FRCDIVN
÷ 2
FOSC
FRCDIV<2:0>
TUN<5:0>
S7
÷ 16
FRCDIV16
FRC
LPRC
LPRC
Oscillator
S6
Reference Clock Generation
POSCCLK
S0
÷ N
FOSC
REFCLKO
RPn
S5
ROSEL RODIV<3:0>
Clock Fail
Clock Switch
S7
Note
1:
Reset
NOSC<2:0> FNOSC<2:0>
WDT, PWRT,
FSCM
See Figure 9-2 for PLL and FVCO details.
2:
If the Oscillator is used with XT or HS modes, an external parallel resistor with the value of 1 MΩ must be connected.
3:
The term FP refers to the clock source for all peripherals, while FCY refers to the clock source for the CPU. Throughout this document, FCY and FP are used interchangeably, except in the case of DOZE mode. FP and FCY will be different when DOZE mode is
used with a doze ratio of 1:2 or lower.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 151
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
9.1
CPU Clocking System
Instruction execution speed or device operating
frequency, FCY, is given by Equation 9-1.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X family of devices
provide seven system clock options:
•
•
•
•
•
•
EQUATION 9-1:
Fast RC (FRC) Oscillator
FRC Oscillator with Phase-Locked Loop (PLL)
FRC Oscillator with postscaler
Primary (XT, HS or EC) Oscillator
Primary Oscillator with PLL
Low-Power RC (LPRC) Oscillator
FIGURE 9-2:
DEVICE OPERATING
FREQUENCY
FCY = Fosc/2
Figure 9-2 is a block diagram of the PLL module.
Equation 9-2 provides the relation between input
frequency (FIN) and output frequency (FOSC).
Equation 9-3 provides the relation between input
frequency (FIN) and VCO frequency (FSYS).
PLL BLOCK DIAGRAM
0.8 MHz < FPLLI(1) < 8.0 MHz
FIN
FPLLI
÷ N1
FOSC ≤120 MHz @ +125ºC
FOSC ≤140 MHz @ +85ºC
120 MHZ < FSYS(1) < 340 MHZ
FSYS
PFD
VCO
FOSC
÷ N2
PLLPRE<4:0>
PLLPOST<1:0>
÷M
PLLDIV<8:0>
Note 1:
This frequency range must be met at all times.
EQUATION 9-2:
FOSC CALCULATION
M
F OSC = F IN × ⎛ ----------------------⎞ = F IN ×
⎝ N1 × N2⎠
( PLLDIV + 2 )
⎛ ----------------------------------------------------------------------------------------⎞
⎝ ( PLLPRE + 2 ) × 2 ( PLLPOST + 1 )⎠
Where,
N1 = PLLPRE + 2
N2 = 2 x (PLLPOST + 1)
M = PLLDIV + 2
EQUATION 9-3:
FVCO CALCULATION
M
F SYS = F IN × ⎛ -------⎞ = F IN ×
⎝ N1⎠
DS70657E-page 152
( PLLDIV + 2 )-⎞
⎛ -----------------------------------⎝ ( PLLPRE + 2 )⎠
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 9-1:
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
Oscillator Mode
Oscillator Source
Fast RC Oscillator with Divide-by-N (FRCDIVN)
POSCMD<1:0> FNOSC<2:0>
See
Note
Internal
xx
111
Low-Power RC Oscillator (LPRC)
Internal
xx
101
1
Primary Oscillator (HS) with PLL (HSPLL)
Primary
10
011
—
Primary Oscillator (XT) with PLL (XTPLL)
Primary
01
011
—
Primary Oscillator (EC) with PLL (ECPLL)
Primary
00
011
1
Primary Oscillator (HS)
Primary
10
010
—
Primary Oscillator (XT)
Primary
01
010
—
Primary Oscillator (EC)
Primary
00
010
1
Fast RC Oscillator (FRC) with divide-by-N and
PLL (FRCPLL)
Internal
xx
001
1
Fast RC Oscillator (FRC)
Internal
xx
000
1
Note 1:
2:
9.2
1, 2
OSC2 pin function is determined by the OSCIOFNC Configuration bit.
This is the default oscillator mode for an unprogrammed (erased) device.
Oscillator Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
9.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 7. “Oscillator” (DS70580)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 153
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
OSCCON: OSCILLATOR CONTROL REGISTER(1,3)
REGISTER 9-1:
U-0
R-0
—
R-0
R-0
COSC<2:0>
U-0
R/W-y
R/W-y
R/W-y
NOSC<2:0>(2)
—
bit 15
bit 8
R/W-0
R/W-0
R-0
U-0
R/W-0
U-0
U-0
R/W-0
CLKLOCK
IOLOCK
LOCK
—
CF
—
—
OSWEN
bit 7
bit 0
Legend:
y = Value set from Configuration bits on POR
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
COSC<2:0>: Current Oscillator Selection bits (read-only)
111 = Fast RC Oscillator (FRC) with Divide-by-n
110 = Fast RC Oscillator (FRC) with Divide-by-16
101 = Low-Power RC Oscillator (LPRC)
100 = Reserved
011 = Primary Oscillator (XT, HS, EC) with PLL
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator (FRC) with divide-by-N and PLL (FRCPLL)
000 = Fast RC Oscillator (FRC)
bit 11
Unimplemented: Read as ‘0’
bit 10-8
NOSC<2:0>: New Oscillator Selection bits(2)
111 = Fast RC Oscillator (FRC) with Divide-by-n
110 = Fast RC Oscillator (FRC) with Divide-by-16
101 = Low-Power RC Oscillator (LPRC)
100 = Reserved
011 = Primary Oscillator (XT, HS, EC) with PLL
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator (FRC) with divide-by-N and PLL (FRCPLL)
000 = Fast RC Oscillator (FRC)
bit 7
CLKLOCK: Clock Lock Enable bit
1 = If (FCKSM0 = 1), then clock and PLL configurations are locked
If (FCKSM0 = 0), then clock and PLL configurations may be modified
0 = Clock and PLL selections are not locked, configurations may be modified
bit 6
IOLOCK: I/O Lock Enable bit
1 = I/O Lock is active
0 = I/O Lock is not active
bit 5
LOCK: PLL Lock Status bit (read-only)
1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied
0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
bit 4
Unimplemented: Read as ‘0’
Note 1:
2:
3:
Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70580) in the
“dsPIC33E/PIC24E Family Reference Manual” (available from the Microchip web site) for details.
Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC
mode as a transition clock source between the two PLL modes.
This register resets only on a Power-on Reset (POR).
DS70657E-page 154
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 9-1:
OSCCON: OSCILLATOR CONTROL REGISTER(1,3) (CONTINUED)
bit 3
CF: Clock Fail Detect bit
1 = FSCM has detected clock failure
0 = FSCM has not detected clock failure
bit 2-1
Unimplemented: Read as ‘0’
bit 0
OSWEN: Oscillator Switch Enable bit
1 = Request oscillator switch to selection specified by NOSC<2:0> bits
0 = Oscillator switch is complete
Note 1:
2:
3:
Writes to this register require an unlock sequence. Refer to Section 7. “Oscillator” (DS70580) in the
“dsPIC33E/PIC24E Family Reference Manual” (available from the Microchip web site) for details.
Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC
mode as a transition clock source between the two PLL modes.
This register resets only on a Power-on Reset (POR).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 155
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 9-2:
R/W-0
CLKDIV: CLOCK DIVISOR REGISTER(2)
R/W-0
R/W-1
R/W-1
DOZE<2:0>(3)
ROI
R/W-0
R/W-0
DOZEN(1,4)
R/W-0
R/W-0
FRCDIV<2:0>
bit 15
bit 8
R/W-0
R/W-1
PLLPOST<1:0>
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
PLLPRE<4:0>
bit 7
bit 0
Legend:
y = Value set from Configuration bits on POR
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ROI: Recover on Interrupt bit
1 = Interrupts will clear the DOZEN bit and the processor clock and peripheral clock ratio is set to 1:1
0 = Interrupts have no effect on the DOZEN bit
bit 14-12
DOZE<2:0>: Processor Clock Reduction Select bits(3)
111 = FCY divided by 128
110 = FCY divided by 64
101 = FCY divided by 32
100 = FCY divided by 16
011 = FCY divided by 8 (default)
010 = FCY divided by 4
001 = FCY divided by 2
000 = FCY divided by 1
bit 11
DOZEN: Doze Mode Enable bit(1,4)
1 = DOZE<2:0> field specifies the ratio between the peripheral clocks and the processor clocks
0 = Processor clock and peripheral clock ratio forced to 1:1
bit 10-8
FRCDIV<2:0>: Internal Fast RC Oscillator Postscaler bits
111 = FRC divided by 256
110 = FRC divided by 64
101 = FRC divided by 32
100 = FRC divided by 16
011 = FRC divided by 8
010 = FRC divided by 4
001 = FRC divided by 2
000 = FRC divided by 1 (default)
bit 7-6
PLLPOST<1:0>: PLL VCO Output Divider Select bits (also denoted as ‘N2’, PLL postscaler)
11 = Output divided by 8
10 = Reserved
01 = Output divided by 4 (default)
00 = Output divided by 2
bit 5
Unimplemented: Read as ‘0’
Note 1:
2:
3:
4:
This bit is cleared when the ROI bit is set and an interrupt occurs.
This register resets only on a Power-on Reset (POR).
DOZE<2:0> bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to
DOZE<2:0> are ignored.
The DOZEN bit cannot be set if DOZE<2:0> = 000. If DOZE<2:0> = 000, any attempt by user software to
set the DOZEN bit is ignored.
DS70657E-page 156
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 9-2:
bit 4-0
CLKDIV: CLOCK DIVISOR REGISTER(2) (CONTINUED)
PLLPRE<4:0>: PLL Phase Detector Input Divider Select bits (also denoted as ‘N1’, PLL prescaler)
11111 = Input divided by 33
•
•
•
00001 = Input divided by 3
00000 = Input divided by 2 (default)
Note 1:
2:
3:
4:
This bit is cleared when the ROI bit is set and an interrupt occurs.
This register resets only on a Power-on Reset (POR).
DOZE<2:0> bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to
DOZE<2:0> are ignored.
The DOZEN bit cannot be set if DOZE<2:0> = 000. If DOZE<2:0> = 000, any attempt by user software to
set the DOZEN bit is ignored.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 157
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 9-3:
PLLFBD: PLL FEEDBACK DIVISOR REGISTER(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
PLLDIV<8>
bit 15
bit 8
R/W-0
R/W-0
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
PLLDIV<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-9
Unimplemented: Read as ‘0’
bit 8-0
PLLDIV<8:0>: PLL Feedback Divisor bits (also denoted as ‘M’, PLL multiplier)
111111111 = 513
•
•
•
000110000 = 50 (default)
•
•
•
000000010 = 4
000000001 = 3
000000000 = 2
Note 1:
This register is reset only on a Power-on Reset (POR).
DS70657E-page 158
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 9-4:
OSCTUN: FRC OSCILLATOR TUNING REGISTER(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TUN<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-6
Unimplemented: Read as ‘0’
bit 5-0
TUN<5:0>: FRC Oscillator Tuning bits
111111 = Center frequency -0.375% (7.345 MHz)
•
•
•
100001 = Center frequency -11.625% (6.52 MHz)
100000 = Center frequency -12% (6.49 MHz)
011111 = Center frequency + 11.625% (8.23 MHz)
011110 = Center frequency + 11.25% (8.20 MHz)
•
•
•
000001 = Center frequency + 0.375% (7.40 MHz)
000000 = Center frequency (7.37 MHz nominal)
Note 1:
x = Bit is unknown
This register resets only on a Power-on Reset (POR).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 159
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 9-5:
REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-0
ROON
—
ROSSLP
ROSEL
R/W-0
R/W-0
R/W-0
R/W-0
RODIV<3:0>(1)
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
ROON: Reference Oscillator Output Enable bit
1 = Reference oscillator output enabled on REFCLK(2) pin
0 = Reference oscillator output disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
ROSSLP: Reference Oscillator Run in Sleep bit
1 = Reference oscillator output continues to run in Sleep
0 = Reference oscillator output is disabled in Sleep
bit 12
ROSEL: Reference Oscillator Source Select bit
1 = Oscillator crystal used as the reference clock
0 = System clock used as the reference clock
bit 11-8
RODIV<3:0>: Reference Oscillator Divider bits(1)
1111 = Reference clock divided by 32,768
1110 = Reference clock divided by 16,384
1101 = Reference clock divided by 8,192
1100 = Reference clock divided by 4,096
1011 = Reference clock divided by 2,048
1010 = Reference clock divided by 1,024
1001 = Reference clock divided by 512
1000 = Reference clock divided by 256
0111 = Reference clock divided by 128
0110 = Reference clock divided by 64
0101 = Reference clock divided by 32
0100 = Reference clock divided by 16
0011 = Reference clock divided by 8
0010 = Reference clock divided by 4
0001 = Reference clock divided by 2
0000 = Reference clock
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
2:
x = Bit is unknown
The reference oscillator output must be disabled (ROON = 0) before writing to these bits.
This pin is remappable. See Section 11.4 “Peripheral Pin Select” for more information.
DS70657E-page 160
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
10.0
POWER-SAVING FEATURES
10.1
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 9. “Watchdog
Timer and Power-Saving Modes”
(DS70615) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices provide
the ability to manage power consumption by
selectively managing clocking to the CPU and the
peripherals. In general, a lower clock frequency and
a reduction in the number of peripherals being
clocked constitutes lower consumed power.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices can manage
power consumption in four ways:
•
•
•
•
Clock frequency
Instruction-based Sleep and Idle modes
Software-controlled Doze mode
Selective peripheral control in software
Clock Frequency and Clock
Switching
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices allow a
wide range of clock frequencies to be selected under
application control. If the system clock configuration is
not locked, users can choose low-power or highprecision oscillators by simply changing the NOSC bits
(OSCCON<10:8>). The process of changing a system
clock during operation, as well as limitations to the
process, are discussed in more detail in Section 9.0
“Oscillator Configuration”.
10.2
Instruction-Based Power-Saving
Modes
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices have two
special power-saving modes that are entered
through the execution of a special PWRSAV
instruction. Sleep mode stops clock operation and
halts all code execution. Idle mode halts the CPU
and code execution, but allows peripheral modules
to continue operation. The assembler syntax of the
PWRSAV instruction is shown in Example 10-1.
Note:
SLEEP_MODE and IDLE_MODE are constants defined in the assembler include
file for the selected device.
Sleep and Idle modes can be exited as a result of an
enabled interrupt, WDT time-out or a device Reset. When
the device exits these modes, it is said to “wake up”.
Combinations of these methods can be used to selectively tailor an application’s power consumption while
still maintaining critical application features, such as
timing-sensitive communications.
EXAMPLE 10-1:
PWRSAV INSTRUCTION SYNTAX
PWRSAV #SLEEP_MODE
PWRSAV #IDLE_MODE
; Put the device into Sleep mode
; Put the device into Idle mode
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 161
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
10.2.1
SLEEP MODE
10.2.2
IDLE MODE
The following occur in Sleep mode:
The following occur in Idle mode:
• The system clock source is shut down. If an
on-chip oscillator is used, it is turned off.
• The device current consumption is reduced to a
minimum, provided that no I/O pin is sourcing
current
• The Fail-Safe Clock Monitor does not operate,
since the system clock source is disabled
• The LPRC clock continues to run in Sleep mode if
the WDT is enabled
• The WDT, if enabled, is automatically cleared
prior to entering Sleep mode
• Some device features or peripherals can continue
to operate. This includes items such as the input
change notification on the I/O ports, or peripherals
that use an external clock input.
• Any peripheral that requires the system clock
source for its operation is disabled
• The CPU stops executing instructions
• The WDT is automatically cleared
• The system clock source remains active. By
default, all peripheral modules continue to operate
normally from the system clock source, but can
also be selectively disabled (see Section 10.4
“Peripheral Module Disable”).
• If the WDT or FSCM is enabled, the LPRC also
remains active.
The device wakes up from Sleep mode on any of the
these events:
• Any interrupt source that is individually enabled
• Any form of device Reset
• A WDT time-out
On wake-up from Sleep mode, the processor restarts
with the same clock source that was active when Sleep
mode was entered.
For optimal power savings, the internal regulator and
the Flash regulator can be configured to go into Standby when Sleep mode is entered by clearing the VREGS
(RCON<8>) and VREGSF (RCON<11>) bits (default
configuration).
If the application requires a faster wake-up time, and
can accept higher current requirements, the VREGS
(RCON<8>) and VREGSF (RCON<11>) bits can be set
to keep the internal regulator and the Flash regulator
active during Sleep mode.
DS70657E-page 162
The device wakes from Idle mode on any of these
events:
• Any interrupt that is individually enabled
• Any device Reset
• A WDT time-out
On wake-up from Idle mode, the clock is reapplied to
the CPU and instruction execution will begin (2-4 clock
cycles later), starting with the instruction following the
PWRSAV instruction, or the first instruction in the ISR.
All peripherals also have the option to discontinue
operation when Idle mode is entered to allow for
increased power savings. This option is selectable in
the control register of each peripheral. For example,
the TSIDL bit in the Timer1 Control register
(T1CON<13>).
10.2.3
INTERRUPTS COINCIDENT WITH
POWER SAVE INSTRUCTIONS
Any interrupt that coincides with the execution of a
PWRSAV instruction is held off until entry into Sleep or
Idle mode has completed. The device then wakes up
from Sleep or Idle mode.
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
10.3
Doze Mode
10.4
The preferred strategies for reducing power
consumption are changing clock speed and invoking
one of the power-saving modes. In some
circumstances, this cannot be practical. For example, it
may be necessary for an application to maintain
uninterrupted synchronous communication, even while
it is doing nothing else. Reducing system clock speed
can introduce communication errors, while using a
power-saving mode can stop communications
completely.
Doze mode is a simple and effective alternative method
to reduce power consumption while the device is still
executing code. In this mode, the system clock
continues to operate from the same source and at the
same speed. Peripheral modules continue to be
clocked at the same speed, while the CPU clock speed
is reduced. Synchronization between the two clock
domains is maintained, allowing the peripherals to
access the SFRs while the CPU executes code at a
slower rate.
Doze mode is enabled by setting the DOZEN bit
(CLKDIV<11>). The ratio between peripheral and core
clock speed is determined by the DOZE<2:0> bits
(CLKDIV<14:12>). There are eight possible
configurations, from 1:1 to 1:128, with 1:1 being the
default setting.
Programs can use Doze mode to selectively reduce
power consumption in event-driven applications. This
allows clock-sensitive functions, such as synchronous
communications, to continue without interruption while
the CPU idles, waiting for something to invoke an
interrupt routine. An automatic return to full-speed CPU
operation on interrupts can be enabled by setting the
ROI bit (CLKDIV<15>). By default, interrupt events
have no effect on Doze mode operation.
For example, suppose the device is operating at
20 MIPS and the ECAN module has been configured
for 500 kbps based on this device operating speed. If
the device is placed in Doze mode with a clock
frequency ratio of 1:4, the ECAN module continues to
communicate at the required bit rate of 500 kbps, but
the CPU now starts executing instructions at a
frequency of 5 MIPS.
© 2011-2012 Microchip Technology Inc.
Peripheral Module Disable
The Peripheral Module Disable (PMD) registers
provide a method to disable a peripheral module by
stopping all clock sources supplied to that module.
When a peripheral is disabled using the appropriate
PMD control bit, the peripheral is in a minimum power
consumption state. The control and status registers
associated with the peripheral are also disabled, so
writes to those registers do not have effect and read
values are invalid.
A peripheral module is enabled only if both the
associated bit in the PMD register is cleared and the
peripheral is supported by the specific dsPIC® DSC
variant. If the peripheral is present in the device, it is
enabled in the PMD register by default.
Note:
10.5
If a PMD bit is set, the corresponding
module is disabled after a delay of one
instruction cycle. Similarly, if a PMD bit is
cleared, the corresponding module is
enabled after a delay of one instruction
cycle (assuming the module control registers are already configured to enable
module operation).
Power-Saving Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
10.5.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 9. “Watchdog Timer and Power-Saving
Modes” (DS70615)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
Preliminary
DS70657E-page 163
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 10-1:
PMD1: PERIPHERAL MODULE DISABLE CONTROL REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
T5MD
T4MD
T3MD
T2MD
T1MD
QEI1MD(1)
PWMMD(1)
—
bit 15
bit 8
R/W-0
R/W-0
I2C1MD
U2MD
R/W-0
U1MD
R/W-0
SPI2MD
R/W-0
SPI1MD
U-0
—
R/W-0
C1MD
(2)
R/W-0
AD1MD
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
T5MD: Timer5 Module Disable bit
1 = Timer5 module is disabled
0 = Timer5 module is enabled
bit 14
T4MD: Timer4 Module Disable bit
1 = Timer4 module is disabled
0 = Timer4 module is enabled
bit 13
T3MD: Timer3 Module Disable bit
1 = Timer3 module is disabled
0 = Timer3 module is enabled
bit 12
T2MD: Timer2 Module Disable bit
1 = Timer2 module is disabled
0 = Timer2 module is enabled
bit 11
T1MD: Timer1 Module Disable bit
1 = Timer1 module is disabled
0 = Timer1 module is enabled
bit 10
QEI1MD: QEI1 Module Disable bit(1)
1 = QEI1 module is disabled
0 = QEI1 module is enabled
bit 9
PWMMD: PWM Module Disable bit(1)
1 = PWM module is disabled
0 = PWM module is enabled
bit 8
Unimplemented: Read as ‘0’
bit 7
I2C1MD: I2C1 Module Disable bit
1 = I2C1 module is disabled
0 = I2C1 module is enabled
bit 6
U2MD: UART2 Module Disable bit
1 = UART2 module is disabled
0 = UART2 module is enabled
bit 5
U1MD: UART1 Module Disable bit
1 = UART1 module is disabled
0 = UART1 module is enabled
bit 4
SPI2MD: SPI2 Module Disable bit
1 = SPI2 module is disabled
0 = SPI2 module is enabled
Note 1:
2:
x = Bit is unknown
This bit is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
This bit is available on dsPIC33EPXXXGP50X and dsPIC33EPXXXMC50X devices only.
DS70657E-page 164
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 10-1:
PMD1: PERIPHERAL MODULE DISABLE CONTROL REGISTER 1 (CONTINUED)
bit 3
SPI1MD: SPI1 Module Disable bit
1 = SPI1 module is disabled
0 = SPI1 module is enabled
bit 2
Unimplemented: Read as ‘0’
bit 1
C1MD: ECAN1 Module Disable bit(2)
1 = ECAN1 module is disabled
0 = ECAN1 module is enabled
bit 0
AD1MD: ADC1 Module Disable bit
1 = ADC1 module is disabled
0 = ADC1 module is enabled
Note 1:
2:
This bit is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
This bit is available on dsPIC33EPXXXGP50X and dsPIC33EPXXXMC50X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 165
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 10-2:
PMD2: PERIPHERAL MODULE DISABLE CONTROL REGISTER 2
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
—
IC4MD
IC3MD
IC2MD
IC1MD
bit 15
bit 8
U-0
U-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
—
—
OC4MD
OC3MD
OC2MD
OC1MD
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11
IC4MD: Input Capture 4 Module Disable bit
1 = Input Capture 4 module is disabled
0 = Input Capture 4 module is enabled
bit 10
IC3MD: Input Capture 3 Module Disable bit
1 = Input Capture 3 module is disabled
0 = Input Capture 3 module is enabled
bit 9
IC2MD: Input Capture 2 Module Disable bit
1 = Input Capture 2 module is disabled
0 = Input Capture 2 module is enabled
bit 8
IC1MD: Input Capture 1 Module Disable bit
1 = Input Capture 1 module is disabled
0 = Input Capture 1 module is enabled
bit 7-4
Unimplemented: Read as ‘0’
bit 3
OC4MD: Output Compare 4 Module Disable bit
1 = Output Compare 4 module is disabled
0 = Output Compare 4 module is enabled
bit 2
OC3MD: Output Compare 3 Module Disable bit
1 = Output Compare 3 module is disabled
0 = Output Compare 3 module is enabled
bit 1
OC2MD: Output Compare 2 Module Disable bit
1 = Output Compare 2 module is disabled
0 = Output Compare 2 module is enabled
bit 0
OC1MD: Output Compare 1 Module Disable bit
1 = Output Compare 1 module is disabled
0 = Output Compare 1 module is enabled
DS70657E-page 166
Preliminary
x = Bit is unknown
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 10-3:
PMD3: PERIPHERAL MODULE DISABLE CONTROL REGISTER 3
U-0
—
bit 15
U-0
—
R/W-0
CRCMD
bit 7
U-0
—
bit 9-8
bit 7
bit 6-2
bit 1
bit 0
U-0
—
U-0
—
R/W-0
CMPMD
U-0
—
U-0
—
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
I2C2MD
U-0
—
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-11
bit 10
U-0
—
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
CMPMD: Comparator Module Disable bit
1 = Comparator module is disabled
0 = Comparator module is enabled
Unimplemented: Read as ‘0’
CRCMD: CRC Module Disable bit
1 = CRC module is disabled
0 = CRC module is enabled
Unimplemented: Read as ‘0’
I2C2MD: I2C2 Module Disable bit
1 = I2C2 module is disabled
0 = I2C2 module is enabled
Unimplemented: Read as ‘0’
REGISTER 10-4:
PMD4: PERIPHERAL MODULE DISABLE CONTROL REGISTER 4
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
R/W-0
R/W-0
U-0
U-0
—
—
—
—
REFOMD
CTMUMD
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-4
Unimplemented: Read as ‘0’
bit 3
REFOMD: Reference Clock Module Disable bit
1 = Reference Clock module is disabled
0 = Reference Clock module is enabled
bit 2
CTMUMD: CTMU Module Disable bit
1 = CTMU module is disabled
0 = CTMU module is enabled
bit 1-0
Unimplemented: Read as ‘0’
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 167
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 10-5:
PMD6: PERIPHERAL MODULE DISABLE CONTROL REGISTER 6
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-0
R/W-0
R/W-0
PWM3MD(1) PWM2MD(1) PWM1MD(1)
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-11
Unimplemented: Read as ‘0’
bit 10
PWM3MD: PWM3 Module Disable bit(1)
1 = PWM3 module is disabled
0 = PWM3 module is enabled
bit 9
PWM2MD: PWM2 Module Disable bit(1)
1 = PWM2 module is disabled
0 = PWM2 module is enabled
bit 8
PWM1MD: PWM1 Module Disable bit(1)
1 = PWM1 module is disabled
0 = PWM1 module is enabled
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
x = Bit is unknown
This bit is available in dsPIC33EPXXXMC50X/20X and PIC24EPXXXMC20X devices only.
DS70657E-page 168
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 10-6:
PMD7: PERIPHERAL MODULE DISABLE CONTROL REGISTER 7
U-0
—
bit 15
U-0
—
U-0
U-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
—
—
U-0
—
R/W-0
DMA0MD(1)
DMA1MD(1)
DMA2MD(1)
DMA3MD(1)
R/W-0
U-0
U-0
U-0
PTGMD
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-5
bit 4
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
DMA0MD: DMA0 Module Disable bit(1)
1 = DMA0 module is disabled
0 = DMA0 module is enabled
DMA1MD: DMA1 Module Disable bit(1)
1 = DMA1 module is disabled
0 = DMA1 module is enabled
DMA2MD: DMA2 Module Disable bit(1)
1 = DMA2 module is disabled
0 = DMA2 module is enabled
bit 3
bit 2-0
Note 1:
DMA3MD: DMA3 Module Disable bit(1)
1 = DMA3 module is disabled
0 = DMA3 module is enabled
PTGMD: PTG Module Disable bit
1 = PTG module is disabled
0 = PTG module is enabled
Unimplemented: Read as ‘0’
This single bit enables and disables all four DMA channels.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 169
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 170
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.0
I/O PORTS
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet,
refer to Section 10. “I/O Ports”
(DS70598) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
Many of the device pins are shared among the
peripherals and the parallel I/O ports. All I/O input ports
feature Schmitt Trigger inputs for improved noise
immunity.
11.1
Parallel I/O (PIO) Ports
Generally, a parallel I/O port that shares a pin with a
peripheral is subservient to the peripheral. The
peripheral’s output buffer data and control signals are
provided to a pair of multiplexers. The multiplexers
select whether the peripheral or the associated port
FIGURE 11-1:
has ownership of the output data and control signals of
the I/O pin. The logic also prevents “loop through,” in
which a port’s digital output can drive the input of a
peripheral that shares the same pin. Figure 11-1
illustrates how ports are shared with other peripherals
and the associated I/O pin to which they are connected.
When a peripheral is enabled and the peripheral is
actively driving an associated pin, the use of the pin as
a general purpose output pin is disabled. The I/O pin
can be read, but the output driver for the parallel port bit
is disabled. If a peripheral is enabled, but the peripheral
is not actively driving a pin, that pin can be driven by a
port.
All port pins have eight registers directly associated
with their operation as digital I/O. The data direction
register (TRISx) determines whether the pin is an input
or an output. If the data direction bit is a ‘1’, then the pin
is an input. All port pins are defined as inputs after a
Reset. Reads from the latch (LATx) read the latch.
Writes to the latch write the latch. Reads from the port
(PORTx) read the port pins, while writes to the port pins
write the latch.
Any bit and its associated data and control registers
that are not valid for a particular device is disabled.
This means the corresponding LATx and TRISx
registers and the port pin are read as zeros.
When a pin is shared with another peripheral or
function that is defined as an input only, it is
nevertheless regarded as a dedicated port because
there is no other competing source of outputs.
BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE
Peripheral Module
Output Multiplexers
Peripheral Input Data
Peripheral Module Enable
Peripheral Output Enable
Peripheral Output Data
PIO Module
I/O
1
Output Enable
0
1
Output Data
0
Read TRIS
Data Bus
D
WR TRIS
CK
Q
I/O Pin
TRIS Latch
D
WR LAT +
WR Port
Q
CK
Data Latch
Read LAT
Input Data
Read Port
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 171
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.1.1
11.3
OPEN-DRAIN CONFIGURATION
In addition to the PORT, LAT and TRIS registers for
data control, port pins can also be individually
configured for either digital or open-drain output. This
is controlled by the Open-Drain Control register,
ODCx, associated with each port. Setting any of the
bits configures the corresponding pin to act as an
open-drain output.
The open-drain feature allows the generation of
outputs other than VDD by using external pull-up
resistors. The maximum open-drain voltage allowed
on any pin is the same as the maximum VIH
specification for that particular pin.
See the “Pin Diagrams” section for the available
5V-tolerant pins and Table 30-10 for the maximum
VIH specification for each pin.
11.2
Configuring Analog and Digital
Port Pins
The ANSELx register controls the operation of the
analog port pins. The port pins that are to function as
analog inputs or outputs must have their corresponding
ANSEL and TRIS bits set. In order to use port pins for
I/O functionality with digital modules, such as Timers,
UARTs, etc., the corresponding ANSELx bit must be
cleared.
The input change notification function of the I/O ports
allows devices to generate interrupt requests to the
processor in response to a change-of-state on selected
input pins. This feature can detect input change-ofstates even in Sleep mode, when the clocks are
disabled. Every I/O port pin can be selected (enabled)
for generating an interrupt request on a change-ofstate.
Three control registers are associated with the CN
functionality of each I/O port. The CNENx registers
contain the CN interrupt enable control bits for each of
the input pins. Setting any of these bits enables a CN
interrupt for the corresponding pins.
Each I/O pin also has a weak pull-up and a weak
pull-down connected to it. The pull-ups and pulldowns act as a current source or sink source
connected to the pin, and eliminate the need for
external resistors when push-button or keypad
devices are connected. The pull-ups and pull-downs
are enabled separately using the CNPUx and the
CNPDx registers, which contain the control bits for
each of the pins. Setting any of the control bits
enables the weak pull-ups and/or pull-downs for the
corresponding pins.
Note:
The ANSELx register has a default value of 0xFFFF;
therefore, all pins that share analog functions are
analog (not digital) by default.
Pins with analog functions affected by the ANSELx
registers are listed with a buffer type of Analog in the
Pinout I/O Descriptions (see Table 1-1).
If the TRIS bit is cleared (output) while the ANSELx bit
is set, the digital output level (VOH or VOL) is converted
by an analog peripheral, such as the ADC module or
Comparator module.
When the PORT register is read, all pins configured as
analog input channels are read as cleared (a low level).
Input Change Notification
Pull-ups and pull-downs on change notification pins should always be disabled
when the port pin is configured as a digital
output.
EXAMPLE 11-1:
PORT WRITE/READ
EXAMPLE
MOV
0xFF00, W0
MOV
W0, TRISB
NOP
BTSS
PORTB, #13
;
;
;
;
;
;
Configure PORTB<15:8>
as inputs
and PORTB<7:0>
as outputs
Delay 1 cycle
Next Instruction
Pins configured as digital inputs do not convert an
analog input. Analog levels on any pin defined as a
digital input (including the ANx pins) can cause the
input buffer to consume current that exceeds the
device specifications.
11.2.1
I/O PORT WRITE/READ TIMING
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically this instruction
would be an NOP, as shown in Example 11-1.
DS70657E-page 172
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.4
Peripheral Pin Select
A major challenge in general purpose devices is providing the largest possible set of peripheral features while
minimizing the conflict of features on I/O pins. The challenge is even greater on low pin-count devices. In an
application where more than one peripheral needs to
be assigned to a single pin, inconvenient workarounds
in application code or a complete redesign may be the
only option.
Peripheral pin select configuration provides an
alternative to these choices by enabling peripheral set
selection and their placement on a wide range of I/O
pins. By increasing the pinout options available on a
particular device, users can better tailor the device to
their entire application, rather than trimming the
application to fit the device.
The peripheral pin select configuration feature operates over a fixed subset of digital I/O pins. Users may
independently map the input and/or output of most digital peripherals to any one of these I/O pins. Hardware
safeguards are included that prevent accidental or
spurious changes to the peripheral mapping once it has
been established.
11.4.1
AVAILABLE PINS
The number of available pins is dependent on the
particular device and its pin count. Pins that support the
Peripheral Pin Select feature include the designation,
“RPn” or “RPIn”, in their full pin designation, where “n”
is the remappable pin number. “RP” is used to
designate pins that support both remappable input and
output functions, while “RPI” indicates pins that support
remappable input functions only.
11.4.2
AVAILABLE PERIPHERALS
The peripherals managed by the peripheral pin select
are all digital-only peripherals. These include general
serial communications (UART and SPI), general purpose timer clock inputs, timer-related peripherals (input
capture and output compare) and interrupt-on-change
inputs.
In comparison, some digital-only peripheral modules
are never included in the peripheral pin select feature.
This is because the peripheral’s function requires special I/O circuitry on a specific port and cannot be easily
connected to multiple pins. These modules include I2C
and the PWM. A similar requirement excludes all modules with analog inputs, such as the A/D converter.
A key difference between remappable and non-remappable peripherals is that remappable peripherals are
not associated with a default I/O pin. The peripheral
must always be assigned to a specific I/O pin before it
can be used. In contrast, non-remappable peripherals
are always available on a default pin, assuming that the
peripheral is active and not conflicting with another
peripheral.
© 2011-2012 Microchip Technology Inc.
When a remappable peripheral is active on a given I/O
pin, it takes priority over all other digital I/O and digital
communication peripherals associated with the pin.
Priority is given regardless of the type of peripheral that
is mapped. Remappable peripherals never take priority
over any analog functions associated with the pin.
11.4.3
CONTROLLING PERIPHERAL PIN
SELECT
Peripheral pin select features are controlled through
two sets of SFRs: one to map peripheral inputs, and
one to map outputs. Because they are separately controlled, a particular peripheral’s input and output (if the
peripheral has both) can be placed on any selectable
function pin without constraint.
The association of a peripheral to a peripheral-selectable pin is handled in two different ways, depending on
whether an input or output is being mapped.
11.4.4
INPUT MAPPING
The inputs of the peripheral pin select options are
mapped on the basis of the peripheral. That is, a control
register associated with a peripheral dictates the pin it
will be mapped to. The RPINRx registers are used to
configure peripheral input mapping (see Register 11-1
through Register 11-17). Each register contains sets of
7-bit fields, with each set associated with one of the
remappable peripherals. Programming a given peripheral’s bit field with an appropriate 7-bit value maps the
RPn pin with the corresponding value to that peripheral.
For any given device, the valid range of values for any
bit field corresponds to the maximum number of
peripheral pin selections supported by the device.
For example, Figure 11-2 illustrates remappable pin
selection for the U1RX input.
FIGURE 11-2:
REMAPPABLE INPUT FOR
U1RX
U1RXR<6:0>
0
RP0
1
RP1
2
RP3
U1RX input
to peripheral
n
RPn
Note:
Preliminary
For input only, peripheral pin select functionality
does not have priority over TRISx settings.
Therefore, when configuring RPn pin for input,
the corresponding bit in the TRISx register must
also be configured for input (set to ‘1’).
DS70657E-page 173
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.4.4.1
Virtual Connections
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices support virtual
(internal) connections to the output of the Op amp/
Comparator module (see Figure 25-1 in Section 25.0
“Op amp/Comparator Module”) and the PTG
module (see Section 24.0 “Peripheral Trigger
Generator (PTG) Module”).
In
addition,
dsPIC33EPXXXMC20X/50X
and
PIC24EPXXXMC20X devices support virtual connections to the filtered QEI module inputs FINDX1,
FHOME1, FINDX2 and FHOME2 (see Figure 17-1 in
Section 17.0 “Quadrature Encoder Interface (QEI)
Module
(dsPIC33EPXXXMC20X/50X
and
PIC24EPXXXMC20X Devices Only)”.
EXAMPLE 11-2:
Virtual connections provide a simple way of interperipheral connection without utilizing a physical pin.
For example, by setting the FLT1R<6:0> bits of the
RPINR12 register to the value of ‘b0000001, the
output of the Analog Comparator C1OUT will be
connected to the PWM Fault 1 input, which allows the
Analog Comparator to trigger PWM faults without the
use of an actual physical pin on the device.
Virtual connection to the QEI module allows
peripherals to be connected to the QEI digital filter
input. To utilize this filter, the QEI module must be
enabled, and its inputs must be connected to a physical
RPn pin. Example 11-2 illustrates how the input
capture module can be connected to the QEI digital
filter.
CONNECTING IC1 TO THE HOME1 QEI1 DIGITAL FILTER INPUT ON PIN 43 OF
THE dsPIC33EPXXXMC206 DEVICE
RPINR15 = 0x2500;
RPINR7 = 0x009;
/* Connect the QEI1 HOME1 input to RP37 (pin 43) */
/* Connect the IC1 input to the digital filter on the FHOME1 input */
QEI1IOC = 0x4000;
QEI1CON = 0x8000;
/* Enable the QEI digital filter */
/* Enable the QEI module */
TABLE 11-1:
SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION)
Input Name(1)
Function Name
Register
Configuration Bits
External Interrupt 1
External Interrupt 2
Timer2 External Clock
Input Capture 1
Input Capture 2
Input Capture 3
Input Capture 4
Output Compare Fault A
INT1
INT2
T2CK
IC1
IC2
IC3
IC4
OCFA
RPINR0
RPINR1
RPINR3
RPINR7
RPINR7
RPINR8
RPINR8
RPINR11
INT1R<6:0>
INT2R<6:0>
T2CKR<6:0>
IC1R<6:0>
IC2R<6:0>
IC3R<6:0>
IC4R<6:0>
OCFAR<6:0>
PWM Fault 1(3)
FLT1
RPINR12
FLT1R<6:0>
FLT2
QEA1
QEB1
INDX1
HOME1
U1RX
U2RX
SDI2
SCK2
RPINR12
RPINR14
RPINR14
RPINR15
RPINR15
RPINR18
RPINR19
RPINR22
RPINR22
FLT2R<6:0>
QEA1R<6:0>
QEB1R<6:0>
INDX1R<6:0>
HOM1R<6:0>
U1RXR<6:0>
U2RXR<6:0>
SDI2R<6:0>
SCK2R<6:0>
(3)
PWM Fault 2
QEI1 Phase A(3)
QEI1 Phase B(3)
QEI1 Index(3)
QEI1 Home(3)
UART1 Receive
UART2 Receive
SPI2 Data Input
SPI2 Clock Input
SPI2 Slave Select
SS2
RPINR23
SS2R<6:0>
CAN1 Receive(2)
C1RX
RPINR26
C1RXR<6:0>
PWM Synch Input 1(3)
SYNCI1
RPINR37
SYNCI1R<6:0>
PWM Dead Time Compensation 1(3)
DTCMP1
RPINR38
DTCMP1R<6:0>
PWM Dead Time Compensation 2(3)
DTCMP2
RPINR39
DTCMP2R<6:0>
(3)
PWM Dead Time Compensation 3
DTCMP3
RPINR39
DTCMP3R<6:0>
Note 1: Unless otherwise noted, all inputs use the Schmitt input buffers.
2: This input source is available on dsPIC33EPXXXGP/MC50X devices only.
3: This input source is available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
DS70657E-page 174
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 11-2:
INPUT PIN SELECTION FOR SELECTABLE INPUT SOURCES
Peripheral Pin
Select Input
Register Value
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
001
001
001
001
001
001
001
001
001
001
001
001
001
001
001
001
010
010
010
010
010
010
010
010
010
010
010
010
Legend:
Note 1:
2:
Input/
Output
Pin Assignment
Peripheral Pin
Select Input
Register Value
Input/
Output
Pin Assignment
0000
I
Vss
010 1101
I
RPI45
010 1110
I
RPI46
0001
I
C1OUT(1)
0010
I
C2OUT(1)
010 1111
I
RPI47
(1)
0011
I
C3OUT
011 0000
—
—
0100
I
C4OUT(1)
011 0001
—
—
0101
—
—
011 0010
—
—
0110
I
PTGO30(1)
011 0011
I
RPI51
0111
I
PTGO31(1)
011 0100
I
RPI52
1000
I
FINDX1(1,2)
011 0101
I
RPI53
011 0110
I/O
RP54
1001
I
FHOME1(1,2)
1010
—
—
011 0111
I/O
RP55
1011
—
—
011 1000
I/O
RP56
1100
—
—
011 1001
I/O
RP57
1101
—
—
011 1010
I
RPI58
1110
—
—
011 1011
—
—
1111
—
—
011 1100
—
—
0000
—
—
011 1101
—
—
0001
—
—
011 1110
—
—
0010
—
—
011 1111
—
—
0011
—
—
100 0000
—
—
0100
I/O
RP20
100 0001
—
—
0101
—
—
100 0010
—
—
0110
—
—
100 0011
—
—
0111
—
—
100 0100
—
—
1000
I
RPI24
100 0101
—
—
1001
I
RPI25
100 0110
—
—
1010
—
—
100 0111
—
—
1011
I
RPI27
100 1000
—
—
1100
I
RPI28
100 1001
—
—
1101
—
—
100 1010
—
—
1110
—
—
100 1011
—
—
1111
—
—
100 1100
—
—
0000
I
RPI32
100 1101
—
—
0001
I
RPI33
100 1110
—
—
0010
I
RPI34
100 1111
—
—
0011
I/O
RP35
101 0000
—
—
0100
I/O
RP36
101 0001
—
—
0101
I/O
RP37
101 0010
—
—
0110
I/O
RP38
101 0011
—
—
0111
I/O
RP39
101 0100
—
—
1000
I/O
RP40
101 0101
—
—
1001
I/O
RP41
101 0110
—
—
1010
I/O
RP42
101 0111
—
—
1011
I/O
RP43
101 1000
—
—
Shaded rows indicate PPS input register values that are unimplemented.
See Section 11.4.4.1 “Virtual Connections” for more information on selecting this pin assignment.
These inputs are available on dsPIC33EPXXXGP/MC50X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 175
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 11-2:
INPUT PIN SELECTION FOR SELECTABLE INPUT SOURCES (CONTINUED)
Peripheral Pin
Select Input
Register Value
010
101
101
101
101
101
101
110
110
110
110
110
110
110
110
110
110
110
110
110
Legend:
Note 1:
2:
Input/
Output
Pin Assignment
Peripheral Pin
Select Input
Register Value
Input/
Output
Pin Assignment
1100
I
RPI44
101 1001
—
—
1010
—
—
110 1101
—
—
1011
—
—
110 1110
—
—
1100
—
—
110 1111
—
—
1101
—
—
111 0000
—
—
1110
I
RPI94
111 0001
—
—
1111
I
RPI95
111 0010
—
—
0000
I
RPI96
111 0011
—
—
0001
I/O
RP97
111 0100
—
—
0010
—
—
111 0101
—
—
0011
—
—
111 0110
I/O
RP118
0100
—
—
111 0111
I
RPI119
0101
—
—
111 1000
I/O
RP120
0110
—
—
111 1001
I
RPI121
0111
—
—
111 1010
—
—
1000
—
—
111 1011
—
—
1001
—
—
111 1100
—
—
1010
—
—
111 1101
—
—
1011
—
—
111 1110
—
—
1100
—
—
111 1111
—
—
Shaded rows indicate PPS input register values that are unimplemented.
See Section 11.4.4.1 “Virtual Connections” for more information on selecting this pin assignment.
These inputs are available on dsPIC33EPXXXGP/MC50X devices only.
DS70657E-page 176
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.4.4.2
Output Mapping
FIGURE 11-3:
In contrast to inputs, the outputs of the peripheral pin
select options are mapped on the basis of the pin. In
this case, a control register associated with a particular
pin dictates the peripheral output to be mapped. The
RPORx registers are used to control output mapping.
Like the RPINRx registers, each register contains sets
of 6 bit fields, with each set associated with one RPn
pin (see Register 11-18 through Register 11-27). The
value of the bit field corresponds to one of the peripherals, and that peripheral’s output is mapped to the pin
(see Table 11-3 and Figure 11-3).
MULTIPLEXING REMAPPABLE
OUTPUT FOR RPn
RPnR<5:0>
Default
U1TX Output
SDO2 Output
0
1
2
RPn
Output Data
A null output is associated with the output register reset
value of ‘0’. This is done to ensure that remappable outputs remain disconnected from all output pins by
default.
QEI1CCMP Output
REFCLKO Output
11.4.4.3
48
49
Mapping Limitations
The control schema of the peripheral select pins is not
limited to a small range of fixed peripheral configurations. There are no mutual or hardware-enforced lockouts between any of the peripheral mapping SFRs.
Literally any combination of peripheral mappings
across any or all of the RPn pins is possible. This
includes both many-to-one and one-to-many mappings
of peripheral inputs and outputs to pins. While such
mappings may be technically possible from a configuration point of view, they may not be supportable from
an electrical point of view.
TABLE 11-3:
Function
OUTPUT SELECTION FOR REMAPPABLE PINS (RPn)
RPnR<5:0>
Output Name
DEFAULT PORT
000000
RPn tied to default pin
U1TX
000001
RPn tied to UART1 transmit
U2TX
000011
RPn tied to UART2 transmit
SDO2
001000
RPn tied to SPI2 data output
SCK2
001001
RPn tied to SPI2 clock output
SS2
001010
RPn tied to SPI2 slave select
C1TX(2)
001110
RPn tied to CAN1 transmit
OC1
010000
RPn tied to Output Compare 1 output
OC2
010001
RPn tied to Output Compare 2 output
OC3
010010
RPn tied to Output Compare 3 output
OC4
010011
RPn tied to Output Compare 4 output
C1OUT
011000
RPn tied to Comparator Output 1
C2OUT
011001
RPn tied to Comparator Output 2
C3OUT
011010
RPn tied to Comparator Output 3
SYNCO1(1)
101101
RPn tied to PWM primary time base sync output
QEI1CCMP(1)
101111
RPn tied to QEI 1 counter comparator output
REFCLKO
110001
RPn tied to Reference Clock output
C4OUT
110010
RPn tied to Comparator Output 4
Note 1:
2:
This function is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
This function is available in dsPIC33EPXXXGP/MC50X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 177
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.5
1.
2.
4.
5.
In some cases, certain pins as defined in Table 3010 under “Injection Current”, have internal protection diodes to VDD and VSS. The term “Injection
Current” is also referred to as “Clamp Current”. On
designated pins, with sufficient external current
limiting precautions by the user, I/O pin input voltages are allowed to be greater or less than the
data sheet absolute maximum ratings with respect
to the VSS and VDD supplies. Note that when the
user application forward biases either of the high
or low side internal input clamp diodes, that the
resulting current being injected into the device that
is clamped internally by the VDD and VSS power
rails, may affect the ADC accuracy by four to six
counts.
I/O pins that are shared with any analog input pin,
(i.e., ANx), are always analog pins by default after
any reset. Consequently, configuring a pin as an
analog input pin, automatically disables the digital
input pin buffer and any attempt to read the digital
input level by reading PORTx or LATx will always
return a ‘0’ regardless of the digital logic level on
the pin. To use a pin as a digital I/O pin on a shared
ANx pin, the user application needs to configure
the analog pin configuration registers in the I/O
Ports module, (i.e., ANSELx), by setting the appropriate bit that corresponds to that I/O port pin to a
‘0’.
Note:
3.
I/O Helpful Tips
VOH = 2.4v @ IOH = -8 mA and VDD = 3.3V
The maximum output current sourced by any 8 mA
I/O pin = 12 mA.
LED source current < 12 mA is technically
permitted. Refer to the VOH/IOH graphs in
Section 30.0 “Electrical Characteristics” for
additional information.
6.
Although it is not possible to use a digital
input pin when its analog function is
enabled, it is possible to use the digital I/O
output function, TRISx = 0x0, while the
analog function is also enabled. However,
this is not recommended, particularly if the
analog input is connected to an external
analog voltage source, which would create signal contention between the analog
signal and the output pin driver.
Most I/O pins have multiple functions. Referring to
the device pin diagrams in the data sheet, the priorities of the functions allocated to any pins are
indicated by reading the pin name from left-toright. The left most function name takes precedence over any function to its right in the naming
convention. For example: AN16/T2CK/T7CK/RC1.
This indicates that AN16 is the highest priority in
this example and will supersede all other functions
to its right in the list. Those other functions to its
right, even if enabled, would not work as long as
any other function to its left was enabled. This rule
applies to all of the functions listed for a given pin.
Each pin has an internal weak pull-up resistor
and pull-down resistor that can be configured
using the CNPUx and CNPDx registers, respectively. These resistors eliminate the need for
external resistors in certain applications. The
internal pull-up is up to ~(VDD-0.8), not VDD.
This value is still above the minimum VIH of
CMOS and TTL devices.
DS70657E-page 178
When driving LEDs directly, the I/O pin can source
or sink more current than what is specified in the
VOH/IOH and VOL/IOL DC characteristic specification. The respective IOH and IOL current rating only
applies to maintaining the corresponding output at
or above the VOH and at or below the VOL levels.
However, for LEDs unlike digital inputs of an externally connected device, they are not governed by
the same minimum VIH/VIL levels. An I/O pin output can safely sink or source any current less than
that listed in the absolute maximum rating section
of the data sheet. For example:
Preliminary
The Peripheral Pin Select (PPS) pin mapping rules
are as follows:
a) Only one “output” function can be active on a
given pin at any time regardless if it is a dedicated or remappable function (one pin, one
output).
b) It is possible to assign a “remappable output”
function to multiple pins and externally short
or tie them together for increased current
drive.
c) If any “dedicated output” function is enabled
on a pin it will take precedence over any
remappable “output” function.
d) If any “dedicated digital”, (input or output),
function is enabled on a pin, any number of
“input” remappable functions can be mapped
to the same pin.
e) If any “dedicated analog” function(s) are
enabled on a given pin, “digital input(s)” of any
kind will all be disabled, although a single “digital output” at the user cautionary discretion
can be enabled and active as long as there is
no signal contention with an external analog
input signal. For example it is possible for the
ADC to convert the digital output logic level or
to toggle a digital output on a comparator or
ADC input provided there is no external
analog input like for a built-in self test.
f) Any number of “input” remappable functions
can be mapped to the same pin(s) at the
same time, including to any pin with single
output from either a dedicated or remappable
“output”.
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
g)
h)
The TRIS registers control only the digital I/O
output buffer. Any other dedicated or remappable active “output” will automatically override the TRIS setting. The TRIS register does
not control the digital logic “input” buffer.
Remappable digital “inputs” do not automatically override TRIS settings which means that
the TRIS bit must be set to input for pins with
only remappable input function(s) assigned
All analog pins are enabled by default after
any reset and the corresponding digital input
buffer on the pin is disabled. Only the Analog
pin select registers control the digital input
buffer, not the TRIS register. The user must
disable the analog function on a pin using the
analog pin select registers in order to use any
“digital input(s)” on a corresponding pin, no
exceptions.
© 2011-2012 Microchip Technology Inc.
11.6
I/O Ports Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
11.6.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 2. “I/O Ports” (DS70598)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
Preliminary
DS70657E-page 179
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
11.7
Peripheral Pin Select Registers
REGISTER 11-1:
U-0
RPINR0: PERIPHERAL PIN SELECT INPUT REGISTER 0
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
INT1R<6:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
INT1R<6:0>: Assign External Interrupt 1 (INT1) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7-0
Unimplemented: Read as ‘0’
DS70657E-page 180
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-2:
RPINR1: PERIPHERAL PIN SELECT INPUT REGISTER 1
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INT2R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-0
INT2R<6:0>: Assign External Interrupt 2 (INT2) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 181
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-3:
RPINR3: PERIPHERAL PIN SELECT INPUT REGISTER 3
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T2CKR<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-0
T2CKR<6:0>: Assign Timer2 External Clock (T2CK) to the Corresponding RPn pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 182
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-4:
U-0
RPINR7: PERIPHERAL PIN SELECT INPUT REGISTER 7
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
IC2R<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IC1R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
IC2R<6:0>: Assign Input Capture 2 (IC2) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
IC1R<6:0>: Assign Input Capture 1 (IC1) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 183
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-5:
U-0
RPINR8: PERIPHERAL PIN SELECT INPUT REGISTER 8
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
IC4R<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IC3R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
IC4R<6:0>: Assign Input Capture 4 (IC4) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
IC3R<6:0>: Assign Input Capture 3 (IC3) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 184
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-6:
RPINR11: PERIPHERAL PIN SELECT INPUT REGISTER 11
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
OCFAR<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-0
OCFAR<6:0>: Assign Output Compare Fault A (OCFA) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 185
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-7:
U-0
RPINR12: PERIPHERAL PIN SELECT INPUT REGISTER 12
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
FLT2R<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
FLT1R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
FLT2R<6:0>: Assign PWM Fault 2 (FLT2) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
FLT1R<6:0>: Assign PWM Fault 1 (FLT1) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 186
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-8:
U-0
RPINR14: PERIPHERAL PIN SELECT INPUT REGISTER 14
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
QEB1R<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEA1R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
Unimplemented: Read as ‘0’
bit 14-8
QEB1R<6:0>: Assign B (QEB) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
QEA1R<6:0>: Assign A (QEA) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 187
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-9:
U-0
RPINR15: PERIPHERAL PIN SELECT INPUT REGISTER 15
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
HOME1R<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDX1R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
HOME1R<6:0>: Assign QEI1 HOME1 (HOME1) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
IND1XR<6:0>: Assign QEI1 INDEX1 (INDX1) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 188
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-10: RPINR18: PERIPHERAL PIN SELECT INPUT REGISTER 18
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U1RXR<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-0
U1RXR<6:0>: Assign UART1 Receive (U1RX) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 189
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-11: RPINR19: PERIPHERAL PIN SELECT INPUT REGISTER 19
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U2RXR<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-0
U2RXR<6:0>: Assign UART2 Receive (U2RX) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 190
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-12: RPINR22: PERIPHERAL PIN SELECT INPUT REGISTER 22
U-0
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
SCK2<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SDI2<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
SCK2<6:0>: Assign SPI2 Clock Input (SCK2) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
SDI2<6:0>: Assign SPI2 Data Input (SDI2) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 191
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-13: RPINR23: PERIPHERAL PIN SELECT INPUT REGISTER 23
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SS2<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 6-0
SS2<6:0>: Assign SPI2 Slave Select (SS2) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 192
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-14: RPINR26: PERIPHERAL PIN SELECT INPUT REGISTER 26
(dsPIC33EPXXXGP/MC50X DEVICES ONLY)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
C1RXR<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-7
Unimplemented: Read as ‘0’
bit 6-0
C1RXR<6:0>: Assign CAN1 RX Input (CRX1) to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 193
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-15: RPINR37: PERIPHERAL PIN SELECT INPUT REGISTER 37
(dsPIC33EPXXXMC20X/50X AND PIC24EPXXXMC20X DEVICES ONLY)
U-0
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
SYNCI1R<6:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
SYNCI1R<6:0>: Assign PWM Synchronization Input 1 to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7-0
Unimplemented: Read as ‘0’
DS70657E-page 194
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-16: RPINR38: PERIPHERAL PIN SELECT INPUT REGISTER 38
(dsPIC33EPXXXMC02X AND PIC24EPXXXMC20X DEVICES ONLY)
U-0
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
DTCMP1R<6:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
DTCMP1R<6:0>: Assign PWM Dead Time Compensation Input 1 to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7-0
Unimplemented: Read as ‘0’
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 195
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-17: RPINR39: PERIPHERAL PIN SELECT INPUT REGISTER 39
(dsPIC33EPXXXMC20X/50X AND PIC24EPXXXMC20X DEVICES ONLY)
U-0
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
DTCMP3R<6:0>
bit 15
bit 8
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DTCMP2R<6:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-8
DTCMP3R<6:0>: Assign PWM Dead Time Compensation Input 3 to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
bit 7
Unimplemented: Read as ‘0’
bit 6-0
DTCMP2R<6:0>: Assign PWM Dead Time Compensation Input 2 to the Corresponding RPn Pin bits
(see Table 11-2 for input pin selection numbers)
1111001 = Input tied to RPI121
.
.
.
0000001 = Input tied to CMP1
0000000 = Input tied to VSS
DS70657E-page 196
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-18: RPOR0: PERIPHERAL PIN SELECT OUTPUT REGISTER 0
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP35R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP20R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP35R<5:0>: Peripheral Output Function is Assigned to RP35 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP20R<5:0>: Peripheral Output Function is Assigned to RP20 Output Pin bits (see Table 11-3 for
peripheral function numbers)
REGISTER 11-19: RPOR1: PERIPHERAL PIN SELECT OUTPUT REGISTER 1
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP37R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP36R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP37R<5:0>: Peripheral Output Function is Assigned to RP37 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP36R<5:0>: Peripheral Output Function is Assigned to RP36 Output Pin bits (see Table 11-3 for
peripheral function numbers)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 197
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-20: RPOR2: PERIPHERAL PIN SELECT OUTPUT REGISTER 2
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP39R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP38R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP39R<5:0>: Peripheral Output Function is Assigned to RP39 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP38R<5:0>: Peripheral Output Function is Assigned to RP38 Output Pin bits (see Table 11-3 for
peripheral function numbers)
REGISTER 11-21: RPOR3: PERIPHERAL PIN SELECT OUTPUT REGISTER 3
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP41R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP40R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP41R<5:0>: Peripheral Output Function is Assigned to RP41 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP40R<5:0>: Peripheral Output Function is Assigned to RP40 Output Pin bits (see Table 11-3 for
peripheral function numbers)
DS70657E-page 198
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-22: RPOR4: PERIPHERAL PIN SELECT OUTPUT REGISTER 4
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP43R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP42R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP43R<5:0>: Peripheral Output Function is Assigned to RP43 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP42R<5:0>: Peripheral Output Function is Assigned to RP42 Output Pin bits (see Table 11-3 for
peripheral function numbers)
REGISTER 11-23: RPOR5: PERIPHERAL PIN SELECT OUTPUT REGISTER 5
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP55R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP54R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP55R<5:0>: Peripheral Output Function is Assigned to RP55 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP54R<5:0>: Peripheral Output Function is Assigned to RP54 Output Pin bits (see Table 11-3 for
peripheral function numbers)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 199
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-24: RPOR6: PERIPHERAL PIN SELECT OUTPUT REGISTER 6
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP57R<5:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP56R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP57R<5:0>: Peripheral Output Function is Assigned to RP57 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-6
Unimplemented: Read as ‘0’
bit 5-0
RP56R<5:0>: Peripheral Output Function is Assigned to RP56 Output Pin bits (see Table 11-3 for
peripheral function numbers)
REGISTER 11-25: RPOR7: PERIPHERAL PIN SELECT OUTPUT REGISTER 7
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP97R<5:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP97R<5:0>: Peripheral Output Function is Assigned to RP97 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-0
Unimplemented: Read as ‘0’
DS70657E-page 200
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 11-26: RPOR8: PERIPHERAL PIN SELECT OUTPUT REGISTER 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP118R<5:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-8
RP118R<5:0>: Peripheral Output Function is Assigned to RP118 Output Pin bits (see Table 11-3 for
peripheral function numbers)
bit 7-0
Unimplemented: Read as ‘0’
REGISTER 11-27: RPOR9: PERIPHERAL PIN SELECT OUTPUT REGISTER 9
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP120R<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-6
Unimplemented: Read as ‘0’
bit 5-0
RP120R<5:0>: Peripheral Output Function is Assigned to RP120 Output Pin bits (see Table 11-3 for
peripheral function numbers)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 201
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 202
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
12.0
TIMER1
The Timer1 module can operate in one of the following
modes:
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 11. “Timers”
(DS70362) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
•
•
•
•
In Timer and Gated Timer modes, the input clock is
derived from the internal instruction cycle clock (FCY).
In Synchronous and Asynchronous Counter modes,
the input clock is derived from the external clock input
at the T1CK pin.
The Timer modes are determined by the following bits:
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• Timer Clock Source Control bit (TCS): T1CON<1>
• Timer Synchronization Control bit (TSYNC):
T1CON<2>
• Timer Gate Control bit (TGATE): T1CON<6>
Timer control bit setting for different operating modes
are given in the Table 12-1.
The Timer1 module is a 16-bit timer that can operate as
a free-running interval timer/counter.
TABLE 12-1:
The Timer1 module has the following unique features
over other timers:
TIMER MODE SETTINGS
Mode
• Can be operated in Asynchronous Counter mode
from an external clock source
• The external clock input (T1CK) can optionally be
synchronized to the internal device clock and the
clock synchronization is performed after the
prescaler
A block diagram of Timer1 is shown in Figure 12-1.
FIGURE 12-1:
Timer mode
Gated Timer mode
Synchronous Counter mode
Asynchronous Counter mode
TCS
TGATE
TSYNC
Timer
0
0
x
Gated timer
0
1
x
Synchronous
counter
1
x
1
Asynchronous
counter
1
x
0
16-BIT TIMER1 MODULE BLOCK DIAGRAM
Falling Edge
Detect
Gate
Sync
1
Set T1IF flag
0
FP
(1)
Prescaler
(/n)
10
00
TCKPS<1:0>
T1CLK
TMR1
Reset
x1
Sync
Note 1:
Comparator
1
TSYNC
TCKPS<1:0>
Data
Latch
CLK
0
T1CK
Prescaler
(/n)
TGATE
CTMU
Edge-control
Logic
TGATE
TCS
Equal
PR1
FP is the peripheral clock.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 203
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
12.1
Timer1 Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
12.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 11. “Timers” (DS70362)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
DS70657E-page 204
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
12.2
Timer1 Control Register
REGISTER 12-1:
T1CON: TIMER1 CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
TON(1)
—
TSIDL
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
TGATE
R/W-0
R/W-0
TCKPS<1:0>
U-0
R/W-0
R/W-0
U-0
—
TSYNC(1)
TCS(1)
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timer1 On bit
1 = Starts 16-bit Timer1
0 = Stops 16-bit Timer1
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timer1 Gated Time Accumulation Enable bit
When TCS = 1:
This bit is ignored.
x = Bit is unknown
When TCS = 0:
1 = Gated time accumulation enabled
0 = Gated time accumulation disabled
bit 5-4
TCKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3
Unimplemented: Read as ‘0’
bit 2
TSYNC: Timer1 External Clock Input Synchronization Select bit
When TCS = 1:
1 = Synchronize external clock input
0 = Do not synchronize external clock input
When TCS = 0:
This bit is ignored.
bit 1
TCS: Timer1 Clock Source Select bit
1 = External clock from pin T1CK (on the rising edge)
0 = Internal clock (FP)
bit 0
Unimplemented: Read as ‘0’
Note 1:
When Timer1 is enabled in external synchronous counter mode (TCS = 1, TSYNC = 1, TON = 1), any
attempts by user software to write to the TMR1 register is ignored.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 205
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 206
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
13.0
TIMER2/3 AND TIMER4/5
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X
family
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 11. “Timers”
(DS70362) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
Individually, all four of the 16-bit timers can function as
synchronous timers or counters. They also offer the
features listed above, except for the event trigger; this
is implemented only with Timer2/3. The operating
modes and enabled features are determined by setting
the appropriate bit(s) in the T2CON, T3CON, and
T4CON, T5CON registers. T2CON and T4CON are
shown in generic form in Register 13-1. T3CON and
T5CON are shown in Register 13-2.
For 32-bit timer/counter operation, Timer2 and Timer4
are the least significant word (lsw); Timer3 and Timer5
are the most significant word (msw) of the 32-bit timers.
Note:
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The Timer2/3 and Timer4/5 modules are 32-bit timers,
which can also be configured as four independent
16-bit timers with selectable operating modes.
For 32-bit operation, T3CON and T5CON
control bits are ignored. Only T2CON and
T4CON control bits are used for setup and
control. Timer2 and Timer4 clock and gate
inputs are utilized for the 32-bit timer modules, but an interrupt is generated with the
Timer3 and Timer5 interrupt flags.
A block diagram for an example 32-bit timer pair
(Timer2/3 and Timer4/5) is shown in Figure 13-3.
Note:
As a 32-bit timer, Timer2/3 and Timer4/5 operate in
three modes:
Only Timer2, 3, 4 and 5 can trigger a DMA
data transfer.
• Two Independent 16-bit Timers (e.g., Timer2 and
Timer3) with all 16-bit operating modes (except
Asynchronous Counter mode)
• Single 32-bit Timer
• Single 32-bit Synchronous Counter
They also support these features:
•
•
•
•
•
Timer Gate Operation
Selectable Prescaler Settings
Timer Operation during Idle and Sleep modes
Interrupt on a 32-bit Period Register Match
Time Base for Input Capture and Output Compare
Modules (Timer2 and Timer3 only)
• ADC1 Event Trigger (Timer2/3 only)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 207
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 13-1:
TYPE B TIMER BLOCK DIAGRAM (x = 2 AND 4)
Falling Edge
Detect
Gate
Sync
1
Set TxIF flag
0
FP(1)
Prescaler
(/n)
10
TxCLK
TCKPS<1:0>
Data
Reset
TMRx
00
TGATE
Latch
CLK
TxCK
Prescaler
(/n)
x1
Sync
Comparator
TGATE
TCKPS<1:0>
PRx
TCS
Note 1:
Equal
FP is the peripheral clock.
FIGURE 13-2:
TYPE C TIMER BLOCK DIAGRAM (x = 3 AND 5)
Falling Edge
Detect
Gate
Sync
1
Set TxIF flag
0
FP(1)
Prescaler
(/n)
10
00
TCKPS<1:0>
TxCLK
TMRx
TGATE
Reset
Data
Latch
CLK
TxCK
Prescaler
(/n)
TCKPS<1:0>
x1
Sync
2:
Equal
ADC Start of
Conversion Trigger(2)
TGATE
TCS
Note 1:
Comparator
PRx
FP is the peripheral clock.
The ADC trigger is available on TMR3 and TMR5 only.
DS70657E-page 208
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 13-3:
TYPE B/TYPE C TIMER PAIR BLOCK DIAGRAM (32-BIT TIMER)
Falling Edge
Detect
Gate
Sync
1
Set TyIF flag
PRx
PRy
0
TGATE
FP(1)
Prescaler
(/n)
ADC
Equal
Comparator
Data
10
lsw
00
TCKPS<1:0>
msw
TMRx
TMRy
Latch
CLK
Reset
TxCK
Prescaler
(/n)
x1
Sync
TMRyHLD
TCKPS<1:0>
TGATE
TCS
Data Bus<15:0>
Note 1:
13.1
The ADC trigger is available only on the TMR3:TMR2 andTMR5:TMR4 32-bit timer pairs.
2:
Timerx is a Type B timer (x = 2 and 4).
3:
Timery is a Type C timer (x = 3 and 5).
Timer Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
13.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 11. “Timers” (DS70362)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 209
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
13.2
Timer Control Registers
REGISTER 13-1:
TxCON (T2CON AND T4CON) CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
TON
—
TSIDL
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
TGATE
R/W-0
R/W-0
TCKPS<1:0>
R/W-0
T32
U-0
—
R/W-0
(1)
TCS
bit 7
U-0
—
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timerx On bit
When T32 = 1:
1 = Starts 32-bit Timerx/y
0 = Stops 32-bit Timerx/y
When T32 = 0:
1 = Starts 16-bit Timerx
0 = Stops 16-bit Timerx
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timerx Gated Time Accumulation Enable bit
When TCS = 1:
This bit is ignored.
x = Bit is unknown
When TCS = 0:
1 = Gated time accumulation enabled
0 = Gated time accumulation disabled
bit 5-4
TCKPS<1:0>: Timerx Input Clock Prescale Select bits
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3
T32: 32-bit Timer Mode Select bit
1 = Timerx and Timery form a single 32-bit timer
0 = Timerx and Timery act as two 16-bit timers
bit 2
Unimplemented: Read as ‘0’
bit 1
TCS: Timerx Clock Source Select bit(1)
1 = External clock from pin TxCK (on the rising edge)
0 = Internal clock (FP)
bit 0
Unimplemented: Read as ‘0’
Note 1:
The TxCK pin is not available on all timers. Refer to the “Pin Diagrams” section for the available pins.
DS70657E-page 210
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 13-2:
TyCON (T3CON AND T5CON) CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
U-0
U-0
U-0
TON(1)
—
TSIDL(2)
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
TGATE(1)
R/W-0
R/W-0
TCKPS<1:0>(1)
U-0
U-0
R/W-0
U-0
—
—
TCS(1,3)
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
TON: Timery On bit(1)
1 = Starts 16-bit Timery
0 = Stops 16-bit Timery
bit 14
Unimplemented: Read as ‘0’
bit 13
TSIDL: Stop in Idle Mode bit(2)
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-7
Unimplemented: Read as ‘0’
bit 6
TGATE: Timery Gated Time Accumulation Enable bit(1)
When TCS = 1:
This bit is ignored.
x = Bit is unknown
When TCS = 0:
1 = Gated time accumulation enabled
0 = Gated time accumulation disabled
bit 5-4
TCKPS<1:0>: Timery Input Clock Prescale Select bits(1)
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3-2
Unimplemented: Read as ‘0’
bit 1
TCS: Timery Clock Source Select bit(1,3)
1 = External clock from pin TyCK (on the rising edge)
0 = Internal clock (FP)
bit 0
Unimplemented: Read as ‘0’
Note 1:
2:
3:
When 32-bit operation is enabled (T2CON<3> = 1), these bits have no effect on Timery operation; all timer
functions are set through TxCON.
When 32-bit timer operation is enabled (T32 = 1) in the Timer Control register (TxCON<3>), the TSIDL bit
must be cleared to operate the 32-bit timer in Idle mode.
The TyCK pin is not available on all timers. See “Pin Diagrams” section for the available pins.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 211
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 212
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
14.0
INPUT CAPTURE
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 12. “Input Capture” (DS70352) of the “dsPIC33E/
PIC24E Family Reference Manual”,
which is available from the Microchip web
site (www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 14-1:
The Input Capture module is useful in applications
requiring frequency (period) and pulse measurement.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices support up
to four input capture channels.
Key features of the Input Capture module include:
• Hardware-configurable for 32-bit operation in all
modes by cascading two adjacent modules
• Synchronous and Trigger modes of output
compare operation, with up to 31 user-selectable
trigger/sync sources available
• A 4-level FIFO buffer for capturing and holding
timer values for several events
• Configurable interrupt generation
• Up to six clock sources available for each module,
driving a separate internal 16-bit counter
INPUT CAPTURE MODULE BLOCK DIAGRAM
ICM<2:0>
ICx Pin
ICI<1:0>
Event and
Interrupt
Logic
Edge Detect Logic
and
Clock Synchronizer
Prescaler
Counter
1:1/4/16
CTMU Edge-control
Logic
PTG Trigger
Input
ICTSEL<2:0>
Increment
Clock
Select
IC Clock
Sources
Trigger and
Sync Sources
Trigger and Reset
Sync Logic
16
ICxTMR
4-Level FIFO Buffer
16
16
SYNCSEL<4:0>
Trigger(1)
ICxBUF
ICOV, ICBNE
Note 1:
Set ICxIF
System Bus
The Trigger/Sync source is enabled by default and is set to Timer3 as a source. This timer must be enabled for
proper ICx module operation or the Trigger/Sync source must be changed to another source option.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 213
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
14.1
Input Capture Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
14.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 12. “Input Capture” (DS70352)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
DS70657E-page 214
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
14.2
Input Capture Registers
REGISTER 14-1:
ICxCON1: INPUT CAPTURE x CONTROL REGISTER 1
U-0
U-0
R/W-0
—
—
ICSIDL
R/W-0
R/W-0
R/W-0
ICTSEL<2:0>
U-0
U-0
—
—
bit 15
bit 8
U-0
R/W-0
—
R/W-0
ICI<1:0>
R/HC/HS-0
R/HC/HS-0
ICOV
ICBNE
R/W-0
R/W-0
R/W-0
ICM<2:0>
bit 7
bit 0
Legend:
R = Readable bit
HC = Cleared by Hardware
HS = Set by Hardware
‘0’ = Bit is cleared
-n = Value at POR
W = Writable bit
U = Unimplemented bit, read as ‘0’
bit 15-14
Unimplemented: Read as ‘0’
bit 13
ICSIDL: Input Capture Stop in Idle Control bit
1 = Input capture will Halt in CPU Idle mode
0 = Input capture will continue to operate in CPU Idle mode
bit 12-10
ICTSEL<12:10>: Input Capture Timer Select bits
111 = Peripheral clock (FP) is the clock source of the ICx
110 = Reserved
101 = Reserved
100 = T1CLK is the clock source of the ICx (only the synchronous clock is supported)
011 = T5CLK is the clock source of the ICx
010 = T4CLK is the clock source of the ICx
001 = T2CLK is the clock source of the ICx
000 = T3CLK is the clock source of the ICx
bit 9-7
Unimplemented: Read as ‘0’
bit 6-5
ICI<1:0>: Number of Captures per Interrupt Select bits
(this field is not used if ICM<2:0> = 001 or 111)
11 = Interrupt on every fourth capture event
10 = Interrupt on every third capture event
01 = Interrupt on every second capture event
00 = Interrupt on every capture event
bit 4
ICOV: Input Capture Overflow Status Flag bit (read-only)
1 = Input capture buffer overflow occurred
0 = No input capture buffer overflow occurred
bit 3
ICBNE: Input Capture Buffer Not Empty Status bit (read-only)
1 = Input capture buffer is not empty, at least one more capture value can be read
0 = Input capture buffer is empty
bit 2-0
ICM<2:0>: Input Capture Mode Select bits
111 = Input capture functions as interrupt pin only in CPU Sleep and Idle mode (rising edge detect
only, all other control bits are not applicable)
110 = Unused (module disabled)
101 = Capture mode, every 16th rising edge (Prescaler Capture mode)
100 = Capture mode, every 4th rising edge (Prescaler Capture mode)
011 = Capture mode, every rising edge (Simple Capture mode)
010 = Capture mode, every falling edge (Simple Capture mode)
001 = Capture mode, every edge, rising and falling (Edge Detect mode (ICI<1:0>) is not used in this
mode)
000 = Input Capture module is turned off
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 215
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 14-2:
ICxCON2: INPUT CAPTURE x CONTROL REGISTER 2
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
IC32
bit 15
bit 8
R/W-0
R/W/HS-0
(2)
ICTRIG
TRIGSTAT
(3)
U-0
R/W-0
R/W-1
—
R/W-1
R/W-0
R/W-1
SYNCSEL<4:0>
bit 7
bit 0
Legend:
R = Readable bit
HS = Set by Hardware
‘0’ = Bit is cleared
-n = Value at POR
W = Writable bit
U = Unimplemented bit, read as ‘0’
bit 15-9
Unimplemented: Read as ‘0’
bit 8
IC32: 32-bit Timer Mode Select bit (Cascade mode)
1 = ODD IC and EVEN IC form a single 32-bit Input Capture module(1)
0 = Cascade module operation disabled
bit 7
ICTRIG: Trigger Operation Select bit(2)
1 = Input source used to trigger the input capture timer (Trigger mode)
0 = Input source used to synchronize input capture timer to timer of another module
(Synchronization mode)
bit 6
TRIGSTAT: Timer Trigger Status bit(3)
1 = ICxTMR has been triggered and is running
0 = ICxTMR has not been triggered and is being held clear
bit 5
Unimplemented: Read as ‘0’
Note 1:
2:
3:
4:
5:
6:
The IC32 bit in both the ODD and EVEN IC must be set to enable Cascade mode.
The input source is selected by the SYNCSEL<4:0> bits of the ICxCON2 register.
This bit is set by the selected input source (selected by SYNCSEL<4:0> bits). It can be read, set, and
cleared in software.
Do not use the ICx module as its own sync or trigger source.
This option should only be selected as trigger source and not as a synchronization source.
Each Input Capture module (ICx) has one PTG input source. See Section 24.0 “Peripheral Trigger
Generator (PTG) Module” for more information.
PTGO8 = IC1
PTGO9 = IC2
PTGO10 = IC3
PTGO11 = IC4
DS70657E-page 216
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 14-2:
ICxCON2: INPUT CAPTURE x CONTROL REGISTER 2 (CONTINUED)
SYNCSEL<4:0>: Input Source Select for Synchronization and Trigger Operation bits(4)
11111 = No sync or trigger source for ICx
11110 = Reserved
11101 = Reserved
11100 = CTMU module synchronizes or triggers ICx
11011 = ADC1 module synchronizes or triggers ICx(5)
11010 = CMP3 module synchronizes or triggers ICx(5)
11001 = CMP2 module synchronizes or triggers ICx(5)
11000 = CMP1 module synchronizes or triggers ICx(5)
10111 = Reserved
10110 = Reserved
10101 = Reserved
10100 = Reserved
10011 = IC4 module synchronizes or triggers ICx
10010 = IC3 module synchronizes or triggers ICx
10001 = IC2 module synchronizes or triggers ICx
10000 = IC1 module synchronizes or triggers ICx
01111 = Timer5 synchronizes or triggers ICx
01110 = Timer4 synchronizes or triggers ICx
01101 = Timer3 synchronizes or triggers ICx (default)
01100 = Timer2 synchronizes or triggers ICx
01011 = Timer1 synchronizes or triggers ICx
01010 = PTGOx module synchronizes or triggers ICx(6)
01001 = Reserved
01000 = Reserved
00111 = Reserved
00110 = Reserved
00101 = Reserved
00100 = OC4 module synchronizes or triggers ICx
00011 = OC3 module synchronizes or triggers ICx
00010 = OC2 module synchronizes or triggers ICx
00001 = OC1 module synchronizes or triggers ICx
00000 = No sync or trigger source for ICx
bit 4-0
Note 1:
2:
3:
4:
5:
6:
The IC32 bit in both the ODD and EVEN IC must be set to enable Cascade mode.
The input source is selected by the SYNCSEL<4:0> bits of the ICxCON2 register.
This bit is set by the selected input source (selected by SYNCSEL<4:0> bits). It can be read, set, and
cleared in software.
Do not use the ICx module as its own sync or trigger source.
This option should only be selected as trigger source and not as a synchronization source.
Each Input Capture module (ICx) has one PTG input source. See Section 24.0 “Peripheral Trigger
Generator (PTG) Module” for more information.
PTGO8 = IC1
PTGO9 = IC2
PTGO10 = IC3
PTGO11 = IC4
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 217
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 218
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
15.0
OUTPUT COMPARE
The Output Compare module can select one of eight
available clock sources for its time base. The module
compares the value of the timer with the value of one or
two compare registers depending on the operating
mode selected. The state of the output pin changes
when the timer value matches the compare register
value. The output compare module generates either a
single output pulse or a sequence of output pulses, by
changing the state of the output pin on the compare
match events. The output compare module can also
generate interrupts on compare match events and
trigger DMA data transfers.
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet,
refer to Section 13. “Output Compare”
(DS70358) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
Note:
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 15-1:
See Section 13. “Output Compare”
(DS70358) in the “dsPIC33E/PIC24E
Family Reference Manual” for OCxR and
OCxRS register restrictions.
OUTPUT COMPARE MODULE BLOCK DIAGRAM
OCxCON1
OCxCON2
OCxR
CTMU Edge-Control
Logic
Rollover/Reset
OCxR buffer
Clock
Select
OC Clock
Sources
Increment
Comparator
OCxTMR
Reset
Trigger and
Sync Sources
Trigger and
Sync Logic
Match Event
Comparator
OCx Pin
Match
Event
Rollover
OC Output and
Fault Logic
OCFB
OCFA
Match
Event
OCxRS buffer
SYNCSEL<4:0>
Trigger(1)
PTG Trigger Input
Rollover/Reset
OCxRS
OCx Synchronization/Trigger Event
OCx Interrupt
Reset
Note 1:
The Trigger/Sync source is enabled by default and is set to Timer2 as a source. This timer must be enabled for
proper OCx module operation or the Trigger/Sync source must be changed to another source option.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 219
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
15.1
Output Compare Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
15.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 13. “Output Compare” (DS70358)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
DS70657E-page 220
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
15.2
Output Compare Control Registers
REGISTER 15-1:
U-0
—
bit 15
R/W-0
ENFLTA
bit 7
bit 12-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
Note 1:
2:
U-0
—
R/W-0
OCSIDL
R/W-0
R/W-0
OCTSEL<2:0>
R/W-0
U-0
—
R/W-0
ENFLTB
bit 8
U-0
R/W-0 HCS
R/W-0 HCS
OCFLTB
OCFLTA
R/W-0
TRIGMODE
R/W-0
—
R/W-0
OCM<2:0>
R/W-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13
OCxCON1: OUTPUT COMPAREx CONTROL REGISTER 1
HCS = Hardware Clearable/Settable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
OCSIDL: Stop Output Compare x in Idle Mode Control bit
1 = Output Compare x halts in CPU Idle mode
0 = Output Compare x continues to operate in CPU Idle mode
OCTSEL<2:0>: Output Compare x Clock Select bits
111 = Peripheral clock (FP)
110 = Reserved
101 = PTGOx clock(2)
100 = T1CLK is the clock source of the OCx (only the synchronous clock is supported)
011 = T5CLK is the clock source of the OCx
010 = T4CLK is the clock source of the OCx
001 = T3CLK is the clock source of the OCx
000 = T2CLK is the clock source of the OCx
Unimplemented: Read as ‘0’
ENFLTB: Fault B Input Enable bit
1 = Output Compare Fault B input (OCFB) is enabled
0 = Output Compare Fault B input (OCFB) is disabled
ENFLTA: Fault A Input Enable bit
1 = Output Compare Fault A input (OCFA) is enabled
0 = Output Compare Fault A input (OCFA) is disabled
Unimplemented: Read as ‘0’
OCFLTB: PWM Fault B Condition Status bit
1 = PWM Fault B condition on OCFB pin has occurred
0 = No PWM Fault B condition on OCFB pin has occurred
OCFLTA: PWM Fault A Condition Status bit
1 = PWM Fault A condition on OCFA pin has occurred
0 = No PWM Fault A condition on OCFA pin has occurred
TRIGMODE: Trigger Status Mode Select bit
1 = TRIGSTAT (OCxCON2<6>) is cleared when OCxRS = OCxTMR or in software
0 = TRIGSTAT is cleared only by software
OCxR and OCxRS are double-buffered in PWM mode only.
Each Output Compare module (OCx) has one PTG clock source. See Section 24.0 “Peripheral Trigger
Generator (PTG) Module” for more information.
PTGO4 = OC1
PTGO5 = OC2
PTGO6 = OC3
PTGO7 = OC4
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 221
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 15-1:
bit 2-0
Note 1:
2:
OCxCON1: OUTPUT COMPAREx CONTROL REGISTER 1 (CONTINUED)
OCM<2:0>: Output Compare Mode Select bits
111 = Center-Aligned PWM mode: Output set high when OCxTMR = OCxR and set low when
OCxTMR = OCxRS(1)
110 = Edge-Aligned PWM mode: Output set high when OCxTMR = 0 and set low when
OCxTMR = OCxR(1)
101 = Double Compare Continuous Pulse mode: Initialize OCx pin low, toggle OCx state continuously
on alternate matches of OCxR and OCxRS
100 = Double Compare Single-Shot mode: Initialize OCx pin low, toggle OCx state on matches of
OCxR and OCxRS for one cycle
011 = Single Compare mode: Compare events with OCxR, continuously toggle OCx pin
010 = Single Compare Single-Shot mode: Initialize OCx pin high, compare event with OCxR, forces
OCx pin low
001 = Single Compare Single-Shot mode: Initialize OCx pin low, compare event with OCxR, forces OCx
pin high
000 = Output compare channel is disabled
OCxR and OCxRS are double-buffered in PWM mode only.
Each Output Compare module (OCx) has one PTG clock source. See Section 24.0 “Peripheral Trigger
Generator (PTG) Module” for more information.
PTGO4 = OC1
PTGO5 = OC2
PTGO6 = OC3
PTGO7 = OC4
DS70657E-page 222
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 15-2:
OCxCON2: OUTPUT COMPARE x CONTROL REGISTER 2
R/W-0
FLTMD
bit 15
R/W-0
FLTOUT
R/W-0
FLTTRIEN
R/W-0
OCINV
U-0
U-0
U-0
—
—
—
R/W-0
OCTRIG
bit 7
R/W-0 HS
TRIGSTAT
R/W-0
OCTRIS
R/W-0
R/W-1
R/W-1
SYNCSEL<4:0>
R/W-0
bit 14
bit 13
bit 12
bit 11-9
bit 8
bit 7
bit 6
bit 5
Note 1:
2:
3:
R/W-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
R/W-0
OC32
bit 8
HS = Hardware Settable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
FLTMD: Fault Mode Select bit
1 = Fault mode is maintained until the Fault source is removed; the corresponding OCFLTx bit is
cleared in software and a new PWM period starts
0 = Fault mode is maintained until the Fault source is removed and a new PWM period starts
FLTOUT: Fault Out bit
1 = PWM output is driven high on a Fault
0 = PWM output is driven low on a Fault
FLTTRIEN: Fault Output State Select bit
1 = OCx pin is tri-stated on Fault condition
0 = OCx pin I/O state defined by FLTOUT bit on Fault condition
OCINV: OCMP Invert bit
1 = OCx output is inverted
0 = OCx output is not inverted
Unimplemented: Read as ‘0’
OC32: Cascade Two OCx Modules Enable bit (32-bit operation)
1 = Cascade module operation enabled
0 = Cascade module operation disabled
OCTRIG: OCx Trigger/Sync Select bit
1 = Trigger OCx from source designated by SYNCSELx bits
0 = Synchronize OCx with source designated by SYNCSELx bits
TRIGSTAT: Timer Trigger Status bit
1 = Timer source has been triggered and is running
0 = Timer source has not been triggered and is being held clear
OCTRIS: OCx Output Pin Direction Select bit
1 = OCx is tri-stated
0 = Output compare module drives the OCx pin
Do not use the OCx module as its own synchronization or trigger source.
When the OCy module is turned OFF, it sends a trigger out signal. If the OCx module use the OCy module
as a trigger source, the OCy module must be unselected as a trigger source prior to disabling it.
Each Output Compare module (OCx) has one PTG Trigger/Synchronization source. See Section 24.0
“Peripheral Trigger Generator (PTG) Module” for more information.
PTGO0 = OC1
PTGO1 = OC2
PTGO2 = OC3
PTGO3 = OC4
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 223
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 15-2:
bit 4-0
OCxCON2: OUTPUT COMPARE x CONTROL REGISTER 2 (CONTINUED)
SYNCSEL<4:0>: Trigger/Synchronization Source Selection bits
11111 = No sync or trigger source for OCx
11110 = INT2 pin synchronizes or triggers OCx
11101 = INT1 pin synchronizes or triggers OCx
11100 = CTMU module synchronizes or triggers OCx
11011 = ADC1 module synchronizes or triggers OCx
11010 = CMP3 module synchronizes or triggers OCx
11001 = CMP2 module synchronizes or triggers OCx
11000 = CMP1 module synchronizes or triggers OCx
10111 = Reserved
10110 = Reserved
10101 = Reserved
10100 = Reserved
10011 = IC4 input capture event synchronizes or triggers OCx
10010 = IC3 input capture event synchronizes or triggers OCx
10001 = IC2 input capture event synchronizes or triggers OCx
10000 = IC1 input capture event synchronizes or triggers OCx
01111 = Timer5 synchronizes or triggers OCx
01110 = Timer4 synchronizes or triggers OCx
01101 = Timer3 synchronizes or triggers OCx
01100 = Timer2 synchronizes or triggers OCx (default)
01011 = Timer1 synchronizes or triggers OCx
01010 = PTGOx synchronizes or trigger OCx(3)
01001 = Reserved
01000 = Reserved
00111 = Reserved
00110 = Reserved
00101 = Reserved
00100 = OC4 module synchronizes or triggers OCx(1,2)
00011 = OC3 module synchronizes or triggers OCx(1,2)
00010 = OC2 module synchronizes or triggers OCx(1,2)
00001 = OC1 module synchronizes or triggers OCx(1,2)
00000 = No sync or trigger source for OCx
Note 1:
2:
3:
Do not use the OCx module as its own synchronization or trigger source.
When the OCy module is turned OFF, it sends a trigger out signal. If the OCx module use the OCy module
as a trigger source, the OCy module must be unselected as a trigger source prior to disabling it.
Each Output Compare module (OCx) has one PTG Trigger/Synchronization source. See Section 24.0
“Peripheral Trigger Generator (PTG) Module” for more information.
PTGO0 = OC1
PTGO1 = OC2
PTGO2 = OC3
PTGO3 = OC4
DS70657E-page 224
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
16.0
HIGH-SPEED PWM MODULE
(dsPIC33EPXXXMC20X/50X
and PIC24EPXXXMC20X
DEVICES ONLY)
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 14. “High-Speed
PWM” (DS70645) of the “dsPIC33E/
PIC24E Family Reference Manual”,
which is available from the Microchip web
site (www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The High-Speed PWM module contains up to three
PWM generators. Each PWM generator provides two
PWM outputs: PWMxH and PWMxL. The master time
base generator provides a synchronous signal as a
common time base to synchronize the various PWM
outputs. The individual PWM outputs are available on
the output pins of the device. The input Fault signals
and current-limit signals, when enabled, can monitor
and protect the system by placing the PWM outputs
into a known “safe” state.
Each PWM can generate a trigger to the ADC module
to sample the analog signal at a specific instance during the PWM period. In addition, the High-Speed PWM
module also generates a Special Event Trigger to the
ADC module based on either of the two master time
bases.
The High-Speed PWM module can synchronize itself
with an external signal or can act as a synchronizing
source to any external device. The SYNCI1 input pin
that utilizes PPS, can synchronize the High-Speed
PWM module with an external signal. The SYNCO1 pin
is an output pin that provides a synchronous signal to
an external device.
The
dsPIC33EPXXXMC20X/50X
and
PIC24EPXXXMC20X devices support a dedicated
Pulse-Width Modulation (PWM) module with up to 6
outputs.
Figure 16-1 illustrates an architectural overview of the
High-Speed PWM module and its interconnection with
the CPU and other peripherals.
The High-Speed PWM module consists of the following
major features:
16.1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Three PWM generators
Two PWM outputs per PWM generator
Individual period and duty cycle for each PWM pair
Duty cycle, dead time, phase shift and frequency
resolution of 8.32 ns
Independent Fault and current-limit inputs for six
PWM outputs
Redundant output
Center-Aligned PWM mode
Output override control
Chop mode (also known as Gated mode)
Special Event Trigger
Prescaler for input clock
PWMxL and PWMxH output pin swapping
Independent PWM frequency, duty cycle and
phase shift changes for each PWM generator
Dead-time compensation
Enhanced Leading-Edge Blanking (LEB)
functionality
Frequency resolution enhancement
PWM capture functionality
Note:
The PWM module incorporates multiple external Fault
inputs to include FLT1 and FLT2, which are remappable using the PPS feature, FLT3 and FLT4,
which are available only on the larger 44-pin and 64-pin
packages, and FLT32, which has been implemented
with Class B safety features, and is available on a fixed
pin
on
all
dsPIC33EPXXXMC20X/50X
and
PIC24EPXXXMC20X devices.
These faults provide a safe and reliable way to safely
shut down the PWM outputs when the Fault input is
asserted.
16.1.1
PWM FAULTS AT RESET
During any reset event, the PWM module maintains
ownership of the Class B fault FLT32. At reset, this fault
is enabled in latched mode to guarantee the fail-safe
power-up of the application. The application software
must clear the PWM fault before enabling the HighSpeed Motor Control PWM module. To clear the fault
condition, the FLT32 pin must first be pulled low
externally or the internal pull down resistor in the
CNPDx register can be enabled.
Note:
In Edge-Aligned PWM mode, the duty
cycle, dead-time, phase shift and
frequency resolution are 8.32 ns.
© 2011-2012 Microchip Technology Inc.
PWM Faults
Preliminary
The Fault mode may be changed using
the FLTMOD<1:0> bits (FCLCON<1:0>)
regardless of the state of FLT32.
DS70657E-page 225
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
16.1.2
WRITE-PROTECTED REGISTERS
On
dsPIC33EPXXXMC20X/50X
and
PIC24EPXXXMC20X devices, write protection is
implemented for the IOCONx and FCLCONx registers.
The write protection feature prevents any inadvertent
writes to these registers. This protection feature can be
controlled by the PWMLOCK Configuration bit
(FOSCSEL<6>). The default state of the write
protection feature is enabled (PWMLOCK = 1). The
write protection feature can be disabled by configuring
PWMLOCK = 0.
EXAMPLE 16-1:
To gain write access to these locked registers, the user
application must write two consecutive values of
(0xABCD and 0x4321) to the PWMKEY register to
perform the unlock operation. The write access to the
IOCONx or FCLCONx registers must be the next SFR
access following the unlock process. There can be no
other SFR accesses during the unlock process and
subsequent write access. To write to both the IOCONx
and FCLCONx registers requires two unlock
operations.
The correct unlocking sequence is described in
Example 16-1.
PWM WRITE-PROTECTED REGISTER UNLOCK SEQUENCE
; FLT32 pin must be pulled low externally in order to clear and disable the fault
; Writing to FCLCON1 register requires unlock sequence
mov
mov
mov
mov
mov
mov
#0xabcd,w10
#0x4321,w11
#0x0000,w0
w10, PWMKEY
w11, PWMKEY
w0,FCLCON1
;
;
;
;
;
;
Load first unlock key to w10 register
Load second unlock key to w11 register
Load desired value of FCLCON1 register in w0
Write first unlock key to PWMKEY register
Write second unlock key to PWMKEY register
Write desired value to FCLCON1 register
; Set PWM ownership and polarity using the IOCON1 register
; Writing to IOCON1 register requires unlock sequence
mov
mov
mov
mov
mov
mov
#0xabcd,w10
#0x4321,w11
#0xF000,w0
w10, PWMKEY
w11, PWMKEY
w0,IOCON1
DS70657E-page 226
;
;
;
;
;
;
Load first unlock key to w10 register
Load second unlock key to w11 register
Load desired value of IOCON1 register in w0
Write first unlock key to PWMKEY register
Write second unlock key to PWMKEY register
Write desired value to IOCON1 register
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 16-1:
HIGH-SPEED PWM MODULE ARCHITECTURAL OVERVIEW
SYNCI1
Data Bus
FOSC
Master Time Base
Synchronization Signal
SYNCO1
PWM1 Interrupt
PWM1H
PWM
Generator 1
PWM1L
Fault, Current-Limit
and Dead-Time Compensation
Synchronization Signal
PWM2 Interrupt
CPU
PWM2H
PWM
Generator 2
PWM2L
Fault, Current-Limit
and Dead-Time Compensation
Synchronization Signal
PWM3 Interrupt
PWM3H
PWM
Generator 3
Primary Trigger
ADC Module Primary Special
Event Trigger
PWM3L
Fault, Current-Limit and
Dead-Time Compensation
FLT1-FLT4, FLT32
DTCMP1-DTCMP3
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 227
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 16-2:
HIGH-SPEED PWM MODULE REGISTER INTERCONNECTION DIAGRAM
FOSC
PTCON, PTCON2
Module Control and Timing
SYNCI1
IOCONx and FCLCONx Unlock Register
PWMKEY
PTPER
SYNCO1
Special Event Compare Trigger
SEVTCMP
PTG Trigger Input
Comparator
Special Event
Postscaler
Comparator
Special Event Trigger
Master Time Base Counter
Master Duty Cycle
Primary Master Time Base
Master Duty Cycle Register
PWM Generator 1
PDCx
MUX
Master Period
16-bit Data Bus
Synchronization
MDC
PTG Trigger Input
Clock
Prescaler
PMTMR
PWM Output Mode
Control Logic
Comparator
PWMCAPx
User Override Logic
ADC Trigger
PTMRx
Comparator
PHASEx
TRIGx
PTG Trigger
Input
Interrupt
Logic
Current-Limit
Override Logic
Dead
Time
Logic
Pin
Control
Logic
PWM1H
PWM1L
Fault and
Current-Limit
Logic
Master Period
FCLCONx
Master Duty Cycle
Synchronization
Fault Override Logic
PWMCONx,
AUXCONx
TRGCONx
FLTx
DTCMP1
IOCONx
LEBCONx,
LEBDLYx
ALTDTRx
DTRx
PWMxH
PWM Generator 2 and PWM Generator 3
PWMxL
FLTx
DTCMPx
DS70657E-page 228
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
16.2
PWM Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
16.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 14. “High-Speed PWM” (DS70645)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 229
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
16.3
PWM Control Registers
REGISTER 16-1:
R/W-0
PTEN
bit 15
U-0
—
R/W-0
SYNCEN(1)
bit 7
R/W-0
R/W-0
PTSIDL
HS/HC-0
SESTAT
R/W-0
R/W-0
SYNCSRC<2:0>(1)
R/W-0
SEIEN
R/W-0
EIPU(1)
R/W-0
R/W-0
(1)
SYNCPOL
SYNCOEN(1)
bit 8
R/W-0
R/W-0
R/W-0
SEVTPS<3:0>(1)
R/W-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
PTCON: PWM TIME BASE CONTROL REGISTER
HC = Cleared in Hardware HS = Set in Hardware
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
PTEN: PWM Module Enable bit
1 = PWM module is enabled
0 = PWM module is disabled
Unimplemented: Read as ‘0’
PTSIDL: PWM Time Base Stop in Idle Mode bit
1 = PWM time base halts in CPU Idle mode
0 = PWM time base runs in CPU Idle mode
SESTAT: Special Event Interrupt Status bit
1 = Special Event Interrupt is pending
0 = Special Event Interrupt is not pending
SEIEN: Special Event Interrupt Enable bit
1 = Special Event Interrupt is enabled
0 = Special Event Interrupt is disabled
EIPU: Enable Immediate Period Updates bit(1)
1 = Active Period register is updated immediately
0 = Active Period register updates occur on PWM cycle boundaries
SYNCPOL: Synchronize Input and Output Polarity bit(1)
1 = SYNCI1/SYNCO1 polarity is inverted (active-low)
0 = SYNCI1/SYNCO1 is active-high
SYNCOEN: Primary Time Base Sync Enable bit(1)
1 = SYNCO1 output is enabled
0 = SYNCO1 output is disabled
SYNCEN: External Time Base Synchronization Enable bit(1)
1 = External synchronization of primary time base is enabled
0 = External synchronization of primary time base is disabled
SYNCSRC<2:0>: Synchronous Source Selection bits(1)
111 = Reserved
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6-4
•
•
•
100 = Reserved
011 = PTGO17(2)
010 = PTGO16(2)
001 = Reserved
000 = SYNCI 1 input from PPS
Note 1:
2:
These bits should be changed only when PTEN = 0. In addition, when using the SYNCI1 feature, the user
application must program the period register with a value that is slightly larger than the expected period of
the external synchronization input signal.
See Section 24.0 “Peripheral Trigger Generator (PTG) Module” for information on this selection.
DS70657E-page 230
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-1:
PTCON: PWM TIME BASE CONTROL REGISTER (CONTINUED)
SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits(1)
1111 = 1:16 Postscaler generates Special Event Trigger on every sixteenth compare match event
bit 3-0
•
•
•
0001 = 1:2 Postscaler generates Special Event Trigger on every second compare match event
0000 = 1:1 Postscaler generates Special Event Trigger on every compare match event
Note 1:
2:
These bits should be changed only when PTEN = 0. In addition, when using the SYNCI1 feature, the user
application must program the period register with a value that is slightly larger than the expected period of
the external synchronization input signal.
See Section 24.0 “Peripheral Trigger Generator (PTG) Module” for information on this selection.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 231
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-2:
PTCON2: PWM PRIMARY MASTER CLOCK DIVIDER SELECT REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
R/W-0
R/W-0
R/W-0
PCLKDIV<2:0>(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-3
Unimplemented: Read as ‘0’
bit 2-0
PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(1)
111 = Reserved
110 = Divide by 64
101 = Divide by 32
100 = Divide by 16
011 = Divide by 8
010 = Divide by 4
001 = Divide by 2
000 = Divide by 1, maximum PWM timing resolution (power-on default)
Note 1:
These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
DS70657E-page 232
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-3:
R/W-1
PTPER: PRIMARY MASTER TIME BASE PERIOD REGISTER
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
PTPER<15:8>
bit 15
bit 8
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
PTPER<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
PTPER<15:0>: Primary Master Time Base (PMTMR) Period Value bits
REGISTER 16-4:
R/W-0
SEVTCMP: PWM PRIMARY SPECIAL EVENT COMPARE REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SEVTCMP<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SEVTCMP<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
SEVTCMP<15:0>: Special Event Compare Count Value bits
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 233
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-5:
CHOP: PWM CHOP CLOCK GENERATOR REGISTER
R/W-0
U-0
U-0
U-0
U-0
U-0
CHPCLKEN
—
—
—
—
—
R/W-0
R/W-0
CHOP<9:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CHOP<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CHPCLKEN: Enable Chop Clock Generator bit
1 = Chop clock generator is enabled
0 = Chop clock generator is disabled
bit 14-10
Unimplemented: Read as ‘0’
bit 9-0
CHOP<9:0>: Chop Clock Divider bits
The frequency of the chop clock signal is given by the following expression:
Chop Frequency = (FP/PCLKDIV<2:0)/(CHOP<9:0> + 1)
REGISTER 16-6:
R/W-0
MDC: PWM MASTER DUTY CYCLE REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
MDC<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
MDC<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
MDC<15:0>: Master PWM Duty Cycle Value bits
DS70657E-page 234
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-7:
PWMCONx: PWM CONTROL REGISTER
HS/HC-0
HS/HC-0
HS/HC-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
FLTSTAT(1)
CLSTAT(1)
TRGSTAT
FLTIEN
CLIEN
TRGIEN
ITB(2)
MDCS(2)
bit 15
bit 8
R/W-0
R/W-0
DTC<1:0>
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
DTCP(3)
—
MTBS
CAM(2,4)
XPRES(5)
IUE(2)
bit 7
bit 0
Legend:
HC = Cleared in Hardware HS = Set in Hardware
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
FLTSTAT: Fault Interrupt Status bit(1)
1 = Fault interrupt is pending
0 = No Fault interrupt is pending
This bit is cleared by setting FLTIEN = 0.
bit 14
CLSTAT: Current-Limit Interrupt Status bit(1)
1 = Current-limit interrupt is pending
0 = No current-limit interrupt is pending
This bit is cleared by setting CLIEN = 0.
bit 13
TRGSTAT: Trigger Interrupt Status bit
1 = Trigger interrupt is pending
0 = No trigger interrupt is pending
This bit is cleared by setting TRGIEN = 0.
bit 12
FLTIEN: Fault Interrupt Enable bit
1 = Fault interrupt is enabled
0 = Fault interrupt is disabled and FLTSTAT bit is cleared
bit 11
CLIEN: Current-Limit Interrupt Enable bit
1 = Current-limit interrupt enabled
0 = Current-limit interrupt disabled and CLSTAT bit is cleared
bit 10
TRGIEN: Trigger Interrupt Enable bit
1 = A trigger event generates an interrupt request
0 = Trigger event interrupts are disabled and TRGSTAT bit is cleared
bit 9
ITB: Independent Time Base Mode bit(2)
1 = PHASEx register provides time base period for this PWM generator
0 = PTPER register provides timing for this PWM generator
bit 8
MDCS: Master Duty Cycle Register Select bit(2)
1 = MDC register provides duty cycle information for this PWM generator
0 = PDCx register provides duty cycle information for this PWM generator
Note 1:
2:
3:
4:
5:
Software must clear the interrupt status here and in the corresponding IFS bit in the interrupt controller.
These bits should not be changed after the PWM is enabled (PTEN = 1).
DTC<1:0> = 11 for DTCP to be effective; otherwise, DTCP is ignored.
The Independent Time Base (ITB = 1) mode must be enabled to use Center-Aligned mode. If ITB = 0, the
CAM bit is ignored.
To operate in External Period Reset mode, the ITB bit must be ‘1’ and the CLMOD bit in the FCLCONx
register must be ‘0’.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 235
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-7:
PWMCONx: PWM CONTROL REGISTER (CONTINUED)
bit 7-6
DTC<1:0>: Dead-Time Control bits
11 = Dead-Time Compensation mode
10 = Dead-time function is disabled
01 = Negative dead time actively applied for Complementary Output mode
00 = Positive dead time actively applied for all output modes
bit 5
DTCP: Dead-Time Compensation Polarity bit(3)
When set to ‘1’:
If DTCMPx = 0, PWMLx is shortened and PWMHx is lengthened.
If DTCMPx = 1, PWMHx is shortened and PWMLx is lengthened.
When set to ‘0’:
If DTCMPx = 0, PWMHx is shortened and PWMLx is lengthened.
If DTCMPx = 1, PWMLx is shortened and PWMHx is lengthened.
bit 4
Unimplemented: Read as ‘0’
bit 3
MTBS: Master Time Base Select bit
1 = PWM generator uses the secondary master time base for synchronization and as the clock source
for the PWM generation logic (if secondary time base is available)
0 = PWM generator uses the primary master time base for synchronization and as the clock source
for the PWM generation logic
bit 2
CAM: Center-Aligned Mode Enable bit(2,4)
1 = Center-Aligned mode is enabled
0 = Edge-Aligned mode is enabled
bit 1
XPRES: External PWM Reset Control bit(5)
1 = Current-limit source resets the time base for this PWM generator if it is in Independent Time Base
mode
0 = External pins do not affect PWM time base
bit 0
IUE: Immediate Update Enable bit
1 = Updates to the active MDC/PDCx/DTx/ALTDTRx/PHASEx registers are immediate
0 = Updates to the active MDC/PDCx/DTx/ALTDTRx/PHASEx registers are synchronized to the
PWM time base
Note 1:
2:
3:
4:
5:
Software must clear the interrupt status here and in the corresponding IFS bit in the interrupt controller.
These bits should not be changed after the PWM is enabled (PTEN = 1).
DTC<1:0> = 11 for DTCP to be effective; otherwise, DTCP is ignored.
The Independent Time Base (ITB = 1) mode must be enabled to use Center-Aligned mode. If ITB = 0, the
CAM bit is ignored.
To operate in External Period Reset mode, the ITB bit must be ‘1’ and the CLMOD bit in the FCLCONx
register must be ‘0’.
DS70657E-page 236
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-8:
R/W-0
PDCx: PWM GENERATOR DUTY CYCLE REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PDCx<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PDCx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
PDCx<15:0>: PWM Generator # Duty Cycle Value bits
REGISTER 16-9:
R/W-0
PHASEx: PWM PRIMARY PHASE SHIFT REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PHASEx<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PHASEx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
PHASEx<15:0>: PWM Phase Shift Value or Independent Time Base Period bits for the PWM Generator
Note 1: If ITB (PWMCONx<9>) = 0, the following applies based on the mode of operation:
Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCON<11:10>) = 00, 01 or 10),
PHASEx<15:0> = Phase shift value for PWMxH and PWMxL outputs
2: If ITB (PWMCONx<9>) = 1, the following applies based on the mode of operation:
Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00, 01 or 10),
PHASEx<15:0> = Independent time base period value for PWMxH and PWMxL
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 237
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-10: DTRx: PWM DEAD-TIME REGISTER
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DTRx<13:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DTRx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-0
DTRx<13:0>: Unsigned 14-bit Dead-Time Value bits for PWMx Dead-Time Unit
REGISTER 16-11: ALTDTRx: PWM ALTERNATE DEAD-TIME REGISTER
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ALTDTRx<13:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ALTDTRx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13-0
ALTDTRx<13:0>: Unsigned 14-bit Dead-Time Value bits for PWMx Dead-Time Unit
DS70657E-page 238
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-12: TRGCONx: PWM TRIGGER CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
TRGDIV<3:0>
U-0
U-0
U-0
U-0
—
—
—
—
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TRGSTRT<5:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-12
TRGDIV<3:0>: Trigger # Output Divider bits
1111 = Trigger output for every 16th trigger event
1110 = Trigger output for every 15th trigger event
1101 = Trigger output for every 14th trigger event
1100 = Trigger output for every 13th trigger event
1011 = Trigger output for every 12th trigger event
1010 = Trigger output for every 11th trigger event
1001 = Trigger output for every 10th trigger event
1000 = Trigger output for every 9th trigger event
0111 = Trigger output for every 8th trigger event
0110 = Trigger output for every 7th trigger event
0101 = Trigger output for every 6th trigger event
0100 = Trigger output for every 5th trigger event
0011 = Trigger output for every 4th trigger event
0010 = Trigger output for every 3rd trigger event
0001 = Trigger output for every 2nd trigger event
0000 = Trigger output for every trigger event
bit 11-6
Unimplemented: Read as ‘0’
bit 5-0
TRGSTRT<5:0>: Trigger Postscaler Start Enable Select bits
111111 = Wait 63 PWM cycles before generating the first trigger event after the module is enabled
•
•
•
000010 = Wait 2 PWM cycles before generating the first trigger event after the module is enabled
000001 = Wait 1 PWM cycles before generating the first trigger event after the module is enabled
000000 = Wait 0 PWM cycles before generating the first trigger event after the module is enabled
Note 1:
The secondary PWM generator cannot generate PWM trigger interrupts.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 239
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-13: IOCONx: PWM I/O CONTROL REGISTER(2)
R/W-0
R/W-0
R/W-0
R/W-0
PENH
PENL
POLH
POLL
R/W-0
R/W-0
PMOD<1:0>(1)
R/W-0
R/W-0
OVRENH
OVRENL
bit 15
bit 8
R/W-0
R/W-0
OVRDAT<1:0>
R/W-0
R/W-0
R/W-0
FLTDAT<1:0>
R/W-0
CLDAT<1:0>
R/W-0
R/W-0
SWAP
OSYNC
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
PENH: PWMxH Output Pin Ownership bit
1 = PWM module controls PWMxH pin
0 = GPIO module controls PWMxH pin
bit 14
PENL: PWMxL Output Pin Ownership bit
1 = PWM module controls PWMxL pin
0 = GPIO module controls PWMxL pin
bit 13
POLH: PWMxH Output Pin Polarity bit
1 = PWMxH pin is active-low
0 = PWMxH pin is active-high
bit 12
POLL: PWMxL Output Pin Polarity bit
1 = PWMxL pin is active-low
0 = PWMxL pin is active-high
bit 11-10
PMOD<1:0>: PWM # I/O Pin Mode bits(1)
11 = Reserved; do not use
10 = PWM I/O pin pair is in the Push-Pull Output mode
01 = PWM I/O pin pair is in the Redundant Output mode
00 = PWM I/O pin pair is in the Complementary Output mode
bit 9
OVRENH: Override Enable for PWMxH Pin bit
1 = OVRDAT<1> controls output on PWMxH pin
0 = PWM generator controls PWMxH pin
bit 8
OVRENL: Override Enable for PWMxL Pin bit
1 = OVRDAT<0> controls output on PWMxL pin
0 = PWM generator controls PWMxL pin
bit 7-6
OVRDAT<1:0>: Data for PWMxH, PWMxL Pins if Override is Enabled bits
If OVERENH = 1, PWMxH is driven to the state specified by OVRDAT<1>.
If OVERENL = 1, PWMxL is driven to the state specified by OVRDAT<0>.
bit 5-4
FLTDAT<1:0>: Data for PWMxH and PWMxL Pins if FLTMOD is Enabled bits
If Fault is active, PWMxH is driven to the state specified by FLTDAT<1>.
If Fault is active, PWMxL is driven to the state specified by FLTDAT<0>.
bit 3-2
CLDAT<1:0>: Data for PWMxH and PWMxL Pins if CLMOD is Enabled bits
If current-limit is active, PWMxH is driven to the state specified by CLDAT<1>.
If current-limit is active, PWMxL is driven to the state specified by CLDAT<0>.
Note 1:
2:
These bits should not be changed after the PWM module is enabled (PTEN = 1).
If the PWMLOCK Configuration bit (FOSCSEL<6>) is a ‘1’, the IOCONx register can only be written after
the unlock sequence has been executed.
DS70657E-page 240
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-13: IOCONx: PWM I/O CONTROL REGISTER(2) (CONTINUED)
bit 1
SWAP: SWAP PWMxH and PWMxL Pins bit
1 = PWMxH output signal is connected to PWMxL pins; PWMxL output signal is connected to
PWMxH pins
0 = PWMxH and PWMxL pins are mapped to their respective pins
bit 0
OSYNC: Output Override Synchronization bit
1 = Output overrides via the OVRDAT<1:0> bits are synchronized to the PWM time base
0 = Output overrides via the OVDDAT<1:0> bits occur on the next CPU clock boundary
Note 1:
2:
These bits should not be changed after the PWM module is enabled (PTEN = 1).
If the PWMLOCK Configuration bit (FOSCSEL<6>) is a ‘1’, the IOCONx register can only be written after
the unlock sequence has been executed.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 241
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-14: TRIGx: PWM PRIMARY TRIGGER COMPARE VALUE REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TRGCMP<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TRGCMP<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
TRGCMP<15:0>: Trigger Control Value bits
When the primary PWM functions in local time base, this register contains the compare values that
can trigger the ADC module.
DS70657E-page 242
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-15: FCLCONx: PWM FAULT CURRENT-LIMIT CONTROL REGISTER(1)
U-0
R/W-0
R/W-0
—
R/W-0
R/W-0
R/W-0
CLSRC<4:0>
R/W-0
R/W-0
CLPOL(2)
CLMOD
bit 15
bit 8
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-0
R/W-0
FLTPOL(2)
FLTSRC<4:0>
R/W-0
FLTMOD<1:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-10
CLSRC<4:0>: Current-Limit Control Signal Source Select bits for PWM Generator #
11111 = Fault 32
11110 = Reserved
•
•
•
01100 = Reserved
01011 = Comparator 4
01010 = Op amp/Comparator 3
01001 = Op amp/Comparator 2
01000 = Op amp/Comparator 1
00111 = Reserved
00110 = Reserved
00101 = Reserved
00100 = Reserved
00011 = Fault 4
00010 = Fault 3
00001 = Fault 2
00000 = Fault 1 (default)
bit 9
CLPOL: Current-Limit Polarity bit for PWM Generator #(2)
1 = The selected current-limit source is active-low
0 = The selected current-limit source is active-high
bit 8
CLMOD: Current-Limit Mode Enable bit for PWM Generator #
1 = Current-Limit mode is enabled
0 = Current-Limit mode is disabled
Note 1:
2:
If the PWMLOCK Configuration bit (FOSCSEL<6>) is a ‘1’, the IOCONx register can only be written after
the unlock sequence has been executed.
These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 243
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-15: FCLCONx: PWM FAULT CURRENT-LIMIT CONTROL REGISTER(1) (CONTINUED)
bit 7-3
FLTSRC<4:0>: Fault Control Signal Source Select bits for PWM Generator #
11111 = Fault 32 (default)
11110 = Reserved
•
•
•
01100 = Reserved
01011 = Comparator 4
01010 = Op amp/Comparator 3
01001 = Op amp/Comparator 2
01000 = Op amp/Comparator 1
00111 = Reserved
00110 = Reserved
00101 = Reserved
00100 = Reserved
00011 = Fault 4
00010 = Fault 3
00001 = Fault 2
00000 = Fault 1
bit 2
FLTPOL: Fault Polarity bit for PWM Generator #(2)
1 = The selected Fault source is active-low
0 = The selected Fault source is active-high
bit 1-0
FLTMOD<1:0>: Fault Mode bits for PWM Generator #
11 = Fault input is disabled
10 = Reserved
01 = The selected Fault source forces PWMxH, PWMxL pins to FLTDAT values (cycle)
00 = The selected Fault source forces PWMxH, PWMxL pins to FLTDAT values (latched condition)
Note 1:
2:
If the PWMLOCK Configuration bit (FOSCSEL<6>) is a ‘1’, the IOCONx register can only be written after
the unlock sequence has been executed.
These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
DS70657E-page 244
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-16: LEBCONx: LEADING-EDGE BLANKING CONTROL REGISTER
R/W-0
PHR
bit 15
R/W-0
PHF
R/W-0
PLR
R/W-0
PLF
R/W-0
FLTLEBEN
R/W-0
CLLEBEN
U-0
—
R/W-0
BCH
R/W-0
BCL
R/W-0
BPHH
R/W-0
BPHL
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9-6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
U-0
—
bit 8
U-0
—
bit 15
U-0
—
W = Writable bit
‘1’ = Bit is set
R/W-0
BPLH
R/W-0
BPLL
bit 0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
PHR: PWMxH Rising Edge Trigger Enable bit
1 = Rising edge of PWMxH will trigger Leading-Edge Blanking counter
0 = Leading-Edge Blanking ignores rising edge of PWMxH
PHF: PWMxH Falling Edge Trigger Enable bit
1 = Falling edge of PWMxH will trigger Leading-Edge Blanking counter
0 = Leading-Edge Blanking ignores falling edge of PWMxH
PLR: PWMxL Rising Edge Trigger Enable bit
1 = Rising edge of PWMxL will trigger Leading-Edge Blanking counter
0 = Leading-Edge Blanking ignores rising edge of PWMxL
PLF: PWMxL Falling Edge Trigger Enable bit
1 = Falling edge of PWMxL will trigger Leading-Edge Blanking counter
0 = Leading-Edge Blanking ignores falling edge of PWMxL
FLTLEBEN: Fault Input Leading-Edge Blanking Enable bit
1 = Leading-Edge Blanking is applied to selected Fault input
0 = Leading-Edge Blanking is not applied to selected Fault input
CLLEBEN: Current-Limit Leading-Edge Blanking Enable bit
1 = Leading-Edge Blanking is applied to selected current-limit input
0 = Leading-Edge Blanking is not applied to selected current-limit input
Unimplemented: Read as ‘0’
BCH: Blanking in Selected Blanking Signal High Enable bit(1)
1 = State blanking (of current-limit and/or Fault input signals) when selected blanking signal is high
0 = No blanking when selected blanking signal is high
BCL: Blanking in Selected Blanking Signal Low Enable bit(1)
1 = State blanking (of current-limit and/or Fault input signals) when selected blanking signal is low
0 = No blanking when selected blanking signal is low
BPHH: Blanking in PWMxH High Enable bit
1 = State blanking (of current-limit and/or Fault input signals) when PWMxH output is high
0 = No blanking when PWMxH output is high
BPHL: Blanking in PWMxH Low Enable bit
1 = State blanking (of current-limit and/or Fault input signals) when PWMxH output is low
0 = No blanking when PWMxH output is low
BPLH: Blanking in PWMxL High Enable bit
1 = State blanking (of current-limit and/or Fault input signals) when PWMxL output is high
0 = No blanking when PWMxL output is high
BPLL: Blanking in PWMxL Low Enable bit
1 = State blanking (of current-limit and/or Fault input signals) when PWMxL output is low
0 = No blanking when PWMxL output is low
The blanking signal is selected via the BLANKSEL bits in the AUXCONx register.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 245
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-17: LEBDLYx: LEADING-EDGE BLANKING DELAY REGISTER
U-0
U-0
U-0
U-0
—
—
—
—
R/W-0
R/W-0
R/W-0
R/W-0
LEB<11:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEB<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-12
Unimplemented: Read as ‘0’
bit 11-0
LEB<11:0>: Leading-Edge Blanking Delay bits for Current-Limit and Fault Inputs
DS70657E-page 246
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 16-18: AUXCONx: PWM AUXILIARY CONTROL REGISTER
U-0
U-0
U-0
U-0
—
—
—
—
R/W-0
R/W-0
R/W-0
R/W-0
BLANKSEL<3:0>
bit 15
bit 8
U-0
U-0
—
—
R/W-0
R/W-0
R/W-0
CHOPSEL<3:0>
R/W-0
R/W-0
R/W-0
CHOPHEN
CHOPLEN
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-12
Unimplemented: Read as ‘0’
bit 11-8
BLANKSEL<3:0>: PWM State Blank Source Select bits
The selected state blank signal will block the current-limit and/or Fault input signals (if enabled via the
BCH and BCL bits in the LEBCONx register).
1001 = Reserved
•
•
•
0100 = Reserved
0011 = PWM3H selected as state blank source
0010 = PWM2H selected as state blank source
0001 = PWM1H selected as state blank source
0000 = No state blanking
bit 7-6
Unimplemented: Read as ‘0’
bit 5-2
CHOPSEL<3:0>: PWM Chop Clock Source Select bits
The selected signal will enable and disable (CHOP) the selected PWM outputs.
1001 = Reserved
•
•
•
0100 = Reserved
0011 = PWM3H selected as CHOP clock source
0010 = PWM2H selected as CHOP clock source
0001 = PWM1H selected as CHOP clock source
0000 = Chop clock generator selected as CHOP clock source
bit 1
CHOPHEN: PWMxH Output Chopping Enable bit
1 = PWMxH chopping function is enabled
0 = PWMxH chopping function is disabled
bit 0
CHOPLEN: PWMxL Output Chopping Enable bit
1 = PWMxL chopping function is enabled
0 = PWMxL chopping function is disabled
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 247
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 248
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
17.0
QUADRATURE ENCODER
INTERFACE (QEI) MODULE
(dsPIC33EPXXXMC20X/50X
and PIC24EPXXXMC20X
DEVICES ONLY)
This chapter describes the Quadrature Encoder Interface (QEI) module and associated operational modes.
The QEI module provides the interface to incremental
encoders for obtaining mechanical position data.
The operational features of the QEI module include:
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 15. “Quadrature
Encoder Interface (QEI)” (DS70601) of
the
“dsPIC33E/PIC24E
Family
Reference Manual”, which is available
from
the
Microchip
web
site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
© 2011-2012 Microchip Technology Inc.
•
•
•
•
•
•
•
•
•
•
•
32-bit position counter
32-bit Index pulse counter
32-bit Interval timer
16-bit velocity counter
32-bit Position Initialization/Capture/Compare
High register
32-bit Position Compare Low register
x4 Quadrature Count mode
External Up/Down Count mode
External Gated Count mode
External Gated Timer mode
Internal Timer mode
Figure 17-1 illustrates the QEI block diagram.
Preliminary
DS70657E-page 249
QEI BLOCK DIAGRAM
FLTREN
GATEN
HOMEx
FHOMEx
DIR_GATE
COUNT
FP
÷ QFDIV
1
COUNT_EN
EXTCNT
0
DIVCLK
INDXx
FINDXx
CCM
Digital
Filter
DIR
Quadrature
Decoder
Logic
QEBx
DIR_GATE
COUNT
CNT_DIR
1’b0
DIR
CNTPOL
EXTCNT
QEAx
Preliminary
DIR_GATE
PCHGE
PCLLE
CNTCMPx
PCLLE
PCHEQ
PCLEQ
PCHGE
32-bit Less Than
or Equal Comparator
OUTFNC
32-bit Greater Than
or Equal Comparator
PCLLE
FP
÷ INTDIV
DIVCLK
32-bit Less Than or Equal
Compare Register
(QEI1LEC)
COUNT_EN
© 2011-2012 Microchip Technology Inc.
(INDXxCNT)
32-bit Index Counter Register
FINDXx
CNT_DIR
INDXxCNTH INDXxCNTL
16-bit Index Counter
Hold Register
(INDXxHLD)
32-bit Interval
Timer Register
(INTxTMR)
32-bit Interval Timer
Hold Register
(INTxHLD)
32-bit Greater Than or Equal
Compare Register
(QEI1GEC)(1)
(POSxCNT)
32-bit Position Counter Register
COUNT_EN
POSxCNTH
POSxCNTL
CNT_DIR
CNT_DIR
COUNT_EN
16-bit Velocity
Counter Register
(VELxCNT)
Data Bus
Note 1:
PCHGE
16-bit Position Counter
Hold Register
(POSxHLD)
QCAPEN
32-bit Initialization and
Capture Register
(QEI1IC)(1)
Data Bus
These registers map to the same memory location.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 250
FIGURE 17-1:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
17.1
QEI Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
17.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 15. “Quadrature Encoder Interface”
(DS70601)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 251
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
17.2
QEI Control Registers
REGISTER 17-1:
R/W-0
QEIEN
bit 15
U-0
—
QEI1CON: QEI CONTROL REGISTER
U-0
—
R/W-0
QEISIDL
R/W-0
R/W-0
R/W-0
INTDIV<2:0>(3)
R/W-0
R/W-0
PIMOD<2:0>(1)
R/W-0
CNTPOL
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12-10
bit 9-8
bit 7
bit 6-4
Note 1:
2:
3:
W = Writable bit
‘1’ = Bit is set
R/W-0
R/W-0
R/W-0
(2)
IMV<1:0>
bit 8
R/W-0
GATEN
R/W-0
R/W-0
CCM<1:0>
bit 0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
QEIEN: Quadrature Encoder Interface Module Counter Enable bit
1 = Module counters are enabled
0 = Module counters are disabled, but SFRs can be read or written to
Unimplemented: Read as ‘0’
QEISIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
PIMOD<2:0>: Position Counter Initialization Mode Select bits(1)
111 = Reserved
110 = Modulo count mode for position counter
101 = Resets the position counter when the position counter equals QEI1GEC register
100 = Second index event after home event initializes position counter with contents of QEI1IC
register
011 = First index event after home event initializes position counter with contents of QEI1IC register
010 = Next index input event initializes the position counter with contents of QEI1IC register
001 = Every Index input event resets the position counter
000 = Index input event does not affect position counter
IMV<1:0>: Index Match Value bits(2)
11 = Index match occurs when QEB = 1 and QEA = 1
10 = Index match occurs when QEB = 1 and QEA = 0
01 = Index match occurs when QEB = 0 and QEA = 1
00 = Index input event does not affect position counter
Unimplemented: Read as ‘0’
INTDIV<2:0>: Timer Input Clock Prescale Select bits (interval timer, main timer (position counter),
velocity counter and index counter internal clock divider select)(3)
111 = 1:128 prescale value
110 = 1:64 prescale value
101 = 1:32 prescale value
100 = 1:16 prescale value
011 = 1:8 prescale value
010 = 1:4 prescale value
001 = 1:2 prescale value
000 = 1:1 prescale value
When CCM = 10 or CCM = 11, all of the QEI counters operate as timers and the PIMOD<2:0> bits are
ignored.
When CCM = 00 and QEA and QEB values match Index Match Value (IMV), the POSCNTH and
POSCNTL registers are reset.
The selected clock rate should be at least twice the expected maximum quadrature count rate.
DS70657E-page 252
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-1:
bit 3
QEI1CON: QEI CONTROL REGISTER (CONTINUED)
CNTPOL: Position and Index Counter/Timer Direction Select bit
1 = Counter direction is negative unless modified by external Up/Down signal
0 = Counter direction is positive unless modified by external Up/Down signal
GATEN: External Count Gate Enable bit
1 = External gate signal controls position counter operation
0 = External gate signal does not affect position counter/timer operation
CCM<1:0>: Counter Control Mode Selection bits
11 = Internal timer mode with optional external count is selected
10 = External clock count with optional external count is selected
01 = External clock count with external up/down direction is selected
00 = Quadrature Encoder Interface (x4 mode) count mode is selected
bit 2
bit 1-0
Note 1:
2:
3:
When CCM = 10 or CCM = 11, all of the QEI counters operate as timers and the PIMOD<2:0> bits are
ignored.
When CCM = 00 and QEA and QEB values match Index Match Value (IMV), the POSCNTH and
POSCNTL registers are reset.
The selected clock rate should be at least twice the expected maximum quadrature count rate.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 253
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-2:
QEI1IOC: QEI I/O CONTROL REGISTER
R/W-0
R/W-0
QCAPEN
FLTREN
R/W-0
R/W-0
R/W-0
R/W-0
QFDIV<2:0>
R/W-0
OUTFNC<1:0>
R/W-0
SWPAB
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R-x
R-x
R-x
R-x
HOMPOL
IDXPOL
QEBPOL
QEAPOL
HOME
INDEX
QEB
QEA
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
QCAPEN: Position Counter Input Capture Enable bit
1 = Positive edge detect of Home input triggers position capture function
0 = HOMEx input event (positive edge) does not trigger a capture event
bit 14
FLTREN: QEAx/QEBx/INDXx/HOMEx Digital Filter Enable bit
1 = Input Pin Digital filter is enabled
0 = Input Pin Digital filter is disabled (bypassed)
bit 13-11
QFDIV<2:0>: QEAx/QEBx/INDXx/HOMEx Digital Input Filter Clock Divide Select bits
111 = 1:256 clock divide
110 = 1:64 clock divide
101 = 1:32 clock divide
100 = 1:16 clock divide
011 = 1:8 clock divide
010 = 1:4 clock divide
001 = 1:2 clock divide
000 = 1:1 clock divide
bit 10-9
OUTFNC<1:0>: QEI Module Output Function Mode Select bits
11 = The CTNCMPx pin goes high when QEI1LEC ≥ POSxCNT ≥ QEI1GEC
10 = The CTNCMPx pin goes high when POSxCNT ≤QEI1LEC
01 = The CTNCMPx pin goes high when POSxCNT ≥ QEI1GEC
00 = Output is disabled
bit 8
SWPAB: Swap QEA and QEB Inputs bit
1 = QEAx and QEBx are swapped prior to quadrature decoder logic
0 = QEAx and QEBx are not swapped
bit 7
HOMPOL: HOMEx Input Polarity Select bit
1 = Input is inverted
0 = Input is not inverted
bit 6
IDXPOL: HOMEx Input Polarity Select bit
1 = Input is inverted
0 = Input is not inverted
bit 5
QEBPOL: QEBx Input Polarity Select bit
1 = Input is inverted
0 = Input is not inverted
bit 4
QEAPOL: QEAx Input Polarity Select bit
1 = Input is inverted
0 = Input is not inverted
bit 3
HOME: Status of HOMEx Input Pin After Polarity Control
1 = Pin is at logic ‘1’
0 = Pin is at logic ‘0’
DS70657E-page 254
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-2:
QEI1IOC: QEI I/O CONTROL REGISTER (CONTINUED)
bit 2
INDEX: Status of INDXx Input Pin After Polarity Control
1 = Pin is at logic ‘1’
0 = Pin is at logic ‘0’
bit 1
QEB: Status of QEBx Input Pin After Polarity Control And SWPAB Pin Swapping
1 = Pin is at logic ‘1’
0 = Pin is at logic ‘0’
bit 0
QEA: Status of QEAx Input Pin After Polarity Control And SWPAB Pin Swapping
1 = Pin is at logic ‘1’
0 = Pin is at logic ‘0’
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 255
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-3:
QEI1STAT: QEI STATUS REGISTER
U-0
U-0
HS, RC-0
—
—
PCHEQIRQ
R/W-0
HS, RC-0
PCHEQIEN PCLEQIRQ
R/W-0
HS, RC-0
R/W-0
PCLEQIEN
POSOVIRQ
POSOVIEN
bit 15
bit 8
HS, RC-0
(1)
PCIIRQ
R/W-0
HS, RC-0
R/W-0
HS, RC-0
R/W-0
HS, RC-0
R/W-0
PCIIEN
VELOVIRQ
VELOVIEN
HOMIRQ
HOMIEN
IDXIRQ
IDXIEN
bit 7
bit 0
Legend:
HS = Set by Hardware
C = Cleared by Software
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
Unimplemented: Read as ‘0’
bit 13
PCHEQIRQ: Position Counter Greater Than or Equal Compare Status bit
1 = POSxCNT ≥ QEI1GEC
0 = POSxCNT < QEI1GEC
bit 12
PCHEQIEN: Position Counter Greater Than or Equal Compare Interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
bit 11
PCLEQIRQ: Position Counter Less Than or Equal Compare Status bit
1 = POSxCNT ≤ QEI1LEC
0 = POSxCNT > QEI1LEC
bit 10
PCLEQIEN: Position Counter Less Than or Equal Compare Interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
bit 9
POSOVIRQ: Position Counter Overflow Status bit
1 = Overflow has occurred
0 = No overflow has occurred
bit 8
POSOVIEN: Position Counter Overflow Interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
bit 7
PCIIRQ: Position Counter (Homing) Initialization Process Complete Status bit(1)
1 = POSxCNT was reinitialized
0 = POSxCNT was not reinitialized
bit 6
PCIIEN: Position Counter (Homing) Initialization Process Complete interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
bit 5
VELOVIRQ: Velocity Counter Overflow Status bit
1 = Overflow has occurred
0 = No overflow has not occurred
bit 4
VELOVIEN: Velocity Counter Overflow Interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
bit 3
HOMIRQ: Status Flag for Home Event Status bit
1 = Home event has occurred
0 = No Home event has occurred
bit 2
HOMIEN: Home Input Event Interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
Note 1:
This status bit is only applicable to PIMOD<2:0> modes ‘011’ and ‘100’.
DS70657E-page 256
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-3:
QEI1STAT: QEI STATUS REGISTER (CONTINUED)
bit 1
IDXIRQ: Status Flag for Index Event Status bit
1 = Index event has occurred
0 = No Index event has occurred
bit 0
IDXIEN: Index Input Event Interrupt Enable bit
1 = Interrupt is enabled
0 = Interrupt is disabled
Note 1:
This status bit is only applicable to PIMOD<2:0> modes ‘011’ and ‘100’.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 257
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-4:
R/W-0
POSxCNTH: POSITION COUNTER HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
POSCNT<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
POSCNT<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
POSCNT<31:16>: High word used to form 32-bit Position Counter Register (POSxCNT) bits
REGISTER 17-5:
R/W-0
POSxCNTL: POSITION COUNTER LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
POSCNT<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
POSCNT<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
POSCNT<15:0>: Low word used to form 32-bit Position Counter Register (POSxCNT) bits
REGISTER 17-6:
R/W-0
POSxHLD: POSITION COUNTER HOLD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
POSHLD<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
POSHLD<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
POSHLD<15:0>: Hold register bits for reading and writing POSxCNTH
DS70657E-page 258
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-7:
R/W-0
VELxCNT: VELOCITY COUNTER REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
VELCNT<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
VELCNT<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
VELCNT<15:0>: Velocity Counter bits
REGISTER 17-8:
R/W-0
INDXxCNTH: INDEX COUNTER HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDXCNT<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDXCNT<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INDXCNT<31:16>: High word used to form 32-bit Index Counter Register (INDXxCNT) bits
REGISTER 17-9:
R/W-0
INDXxCNTL: INDEX COUNTER LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDXCNT<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDXCNT<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INDXCNT<15:0>: Low word used to form 32-bit Index Counter Register (INDXxCNT) bits
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 259
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-10: INDXxHLD: INDEX COUNTER HOLD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDXHLD<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INDXHLD<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INDXHLD<15:0>: Hold register for reading and writing INDXxCNTH bits
REGISTER 17-11: QEI1ICH: INITIALIZATION/CAPTURE HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIIC<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIIC<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
QEIIC<31:16>: High word used to form 32-bit Initialization/Capture Register (QEI1IC) bits
REGISTER 17-12: QEI1ICL: INITIALIZATION/CAPTURE LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIIC<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIIC<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
QEIIC<15:0>: Low word used to form 32-bit Initialization/Capture Register (QEI1IC) bits
DS70657E-page 260
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-13: QEI1LECH: LESS THAN OR EQUAL COMPARE HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEILEC<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEILEC<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
QEILEC<31:16>: High word used to form 32-bit Less Than or Equal Compare Register (QEI1LEC)
bits
REGISTER 17-14: QEI1LECL: LESS THAN OR EQUAL COMPARE LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEILEC<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEILEC<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
QEILEC<15:0>: Low word used to form 32-bit Less Than or Equal Compare Register (QEI1LEC) bits
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 261
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-15: QEI1GECH: GREATER THAN OR EQUAL COMPARE HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIGEC<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIGEC<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
QEIGEC<31:16>: High word used to form 32-bit Greater Than or Equal Compare Register (QEI1GEC)
bits
REGISTER 17-16: QEI1GECL: GREATER THAN OR EQUAL COMPARE LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIGEC<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
QEIGEC<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
QEIGEC<15:0>: Low word used to form 32-bit Greater Than or Equal Compare Register (QEI1GEC)
bits
REGISTER 17-17: INTxTMRH: INTERVAL TIMER HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTTMR<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTTMR<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INTTMR<31:16>: High word used to form 32-bit Interval Timer Register (INTxTMR) bits
DS70657E-page 262
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 17-18: INTxTMRL: INTERVAL TIMER LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTTMR<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTTMR<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INTTMR<15:0>: Low word used to form 32-bit Interval Timer Register (INTxTMR) bits
REGISTER 17-19: INTxHLDH: INTERVAL TIMER HOLD HIGH WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTHLD<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTHLD<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INTHLD<31:16>: Hold register for reading and writing INTxTMRH bits
REGISTER 17-20: INTxHLDL: INTERVAL TIMER HOLD LOW WORD REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTHLD<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTHLD<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
INTHLD<15:0>: Hold register for reading and writing INTxTMRL bits
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 263
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 264
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
18.0
SERIAL PERIPHERAL
INTERFACE (SPI)
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 18. “Serial
Peripheral Interface (SPI)” (DS70569)
of the “dsPIC33E/PIC24E Family
Reference Manual”, which is available
from
the
Microchip
web
site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The SPI module is a synchronous serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices can be
serial EEPROMs, shift registers, display drivers, A/D
converters, etc. The SPI module is compatible with
Motorola’s SPI and SIOP interfaces.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X device family offers
two SPI modules on a single device. These modules,
which are designated as SPI1 and SPI2, are functionally identical. Each SPI module includes an eight-word
FIFO buffer and allows DMA bus connections. When
using the SPI module with DMA, FIFO operation can be
disabled.
Note:
In this section, the SPI modules are
referred to together as SPIx, or separately
as SPI1 and SPI2. Special Function
Registers follow a similar notation. For
example, SPIxCON refers to the control
register for the SPI1 and SPI2 module.
The SPI1 module uses dedicated pins which allow for
a higher speed when using SPI1. The SPI2 module
takes advantage of the Peripheral Pin Select (PPS)
feature to allow for greater flexibility in pin configuration
of the SPI2 module, but results in a lower maximum
speed for SPI2. See Section 30.0 “Electrical
Characteristics” for more information.
The SPIx serial interface consists of four pins, as
follows:
•
•
•
•
SDIx: Serial Data Input
SDOx: Serial Data Output
SCKx: Shift Clock Input or Output
SSx/FSYNCx: Active-Low Slave Select or Frame
Synchronization I/O Pulse
The SPIx module can be configured to operate with
two, three or four pins. In 3-pin mode, SSx is not used.
In 2-pin mode, neither SDOx nor SSx is used.
Figure 18-1 illustrates the block diagram of the SPI
module in Standard and Enhanced modes.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 265
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 18-1:
SPIx MODULE BLOCK DIAGRAM
SCKx
SSx/FSYNCx
1:1 to 1:8
Secondary
Prescaler
Sync
Control
1:1/4/16/64
Primary
Prescaler
Select
Edge
Control
Clock
SPIxCON1<1:0>
Shift Control
SDOx
SPIxCON1<4:2>
Enable
Master Clock
bit 0
SDIx
FP
SPIxSR
Transfer
Transfer
8-Level FIFO
Receive Buffer(1)
8-Level FIFO
Transmit Buffer(1)
SPIxBUF
Read SPIxBUF
Write SPIxBUF
16
Internal Data Bus
Note 1:
In Standard mode, the FIFO is only one level deep.
DS70657E-page 266
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
18.1
1.
Note:
18.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 18. “Serial Peripheral Interface”
(DS70569)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
FRMEN (SPIxCON2<15>) = 1 and SSEN
(SPIxCON1<7>) = 1 are exclusive and invalid.
In Frame mode, SCKx is continuous and the
Frame sync pulse is active on the SSx pin,
which indicates the start of a data frame.
Note:
4.
This will insure that during power-up and
initialization the master/slave will not lose
sync due to an errant SCK transition that
would cause the slave to accumulate data
shift errors for both transmit and receive
appearing as corrupted data.
SPI Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
This insures that the first frame
transmission after initialization is not
shifted or corrupted.
In non-framed 3-wire mode, (i.e., not using SSx
from a master):
a) If CKP (SPIxCON1<6>) = 1, always place a
pull-up resistor on SSx.
b) If CKP = 0, always place a pull-down
resistor on SSx.
Note:
3.
18.2
In Frame mode, if there is a possibility that the
master may not be initialized before the slave:
a) If FRMPOL (SPIxCON2<13>) = 1, use a
pull-down resistor on SSx.
b) If FRMPOL = 0, use a pull-up resistor on
SSx.
Note:
2.
SPI Helpful Tips
Not all third-party devices support Frame
mode timing. Refer to the SPI
specifications in Section 30.0 “Electrical
Characteristics” for details.
In Master mode only, set the SMP bit
(SPIxCON1<9>) to a ‘1’ for the fastest SPI data
rate possible. The SMP bit can only be set at the
same time or after the MSTEN bit
(SPIxCON1<5>) is set.
To avoid invalid slave read data to the master, the
user’s master software must guarantee enough time for
slave software to fill its write buffer before the user
application initiates a master write/read cycle. It is
always advisable to preload the SPIxBUF transmit register in advance of the next master transaction cycle.
SPIxBUF is transferred to the SPI shift register and is
empty once the data transmission begins.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 267
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
18.3
SPI Control Registers
REGISTER 18-1:
SPIxSTAT: SPIx STATUS AND CONTROL REGISTER
R/W-0
U-0
R/W-0
U-0
U-0
SPIEN
—
SPISIDL
—
—
R/W-0
R/W-0
R/W-0
SPIBEC<2:0>
bit 15
bit 8
R/W-0
R/C-0, HS
R/W-0
SRMPT
SPIROV
SRXMPT
R/W-0
R/W-0
R/W-0
SISEL<2:0>
R-0, HS, HC R-0, HS, HC
SPITBF
SPIRBF
bit 7
bit 0
Legend:
C = Clearable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
HS = Set in Hardware bit
HC = Cleared in Hardware bit U = Unimplemented bit, read as ‘0’
x = Bit is unknown
bit 15
SPIEN: SPIx Enable bit
1 = Enables the module and configures SCKx, SDOx, SDIx and SSx as serial port pins
0 = Disables the module
bit 14
Unimplemented: Read as ‘0’
bit 13
SPISIDL: Stop in Idle Mode bit
1 = Discontinue the module operation when device enters Idle mode
0 = Continue the module operation in Idle mode
bit 12-11
Unimplemented: Read as ‘0’
bit 10-8
SPIBEC<2:0>: SPIx Buffer Element Count bits (valid in Enhanced Buffer mode)
Master mode:
Number of SPIx transfers are pending.
Slave mode:
Number of SPIx transfers are unread.
bit 7
SRMPT: Shift Register (SPIxSR) Empty bit (valid in Enhanced Buffer mode)
1 = SPIx Shift register is empty and ready to send or receive the data
0 = SPIx Shift register is not empty
bit 6
SPIROV: Receive Overflow Flag bit
1 = A new byte/word is completely received and discarded. The user application has not read the previous
data in the SPIxBUF register
0 = No overflow has occurred
bit 5
SRXMPT: Receive FIFO Empty bit (valid in Enhanced Buffer mode)
1 = RX FIFO is empty
0 = RX FIFO is not empty
bit 4-2
SISEL<2:0>: SPIx Buffer Interrupt Mode bits (valid in Enhanced Buffer mode)
111 = Interrupt when the SPIx transmit buffer is full (SPIxTBF bit is set)
110 = Interrupt when last bit is shifted into SPIxSR, and as a result, the TX FIFO is empty
101 = Interrupt when the last bit is shifted out of SPIxSR, and the transmit is complete
100 = Interrupt when one data is shifted into the SPIxSR, and as a result, the TX FIFO has one open
memory location
011 = Interrupt when the SPIx receive buffer is full (SPIxRBF bit set)
010 = Interrupt when the SPIx receive buffer is 3/4 or more full
001 = Interrupt when data is available in the receive buffer (SRMPT bit is set)
000 = Interrupt when the last data in the receive buffer is read, as a result, the buffer is empty
(SRXMPT bit set)
DS70657E-page 268
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 18-1:
bit 1
SPIxSTAT: SPIx STATUS AND CONTROL REGISTER (CONTINUED)
SPITBF: SPIx Transmit Buffer Full Status bit
1 = Transmit not yet started, SPIxTXB is full
0 = Transmit started, SPIxTXB is empty
Standard Buffer Mode:
Automatically set in hardware when core writes to the SPIxBUF location, loading SPIxTXB.
Automatically cleared in hardware when SPIx module transfers data from SPIxTXB to SPIxSR.
Enhanced Buffer Mode:
Automatically set in hardware when CPU writes to the SPIxBUF location, loading the last available
buffer location. Automatically cleared in hardware when a buffer location is available for a CPU write
operation.
bit 0
SPIRBF: SPIx Receive Buffer Full Status bit
1 = Receive complete, SPIxRXB is full
0 = Receive is incomplete, SPIxRXB is empty
Standard Buffer Mode:
Automatically set in hardware when SPIx transfers data from SPIxSR to SPIxRXB. Automatically
cleared in hardware when core reads the SPIxBUF location, reading SPIxRXB.
Enhanced Buffer Mode:
Automatically set in hardware when SPIx transfers data from SPIxSR to the buffer, filling the last
unread buffer location. Automatically cleared in hardware when a buffer location is available for a
transfer from SPIxSR.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 269
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 18-2:
U-0
—
bit 15
R/W-0
SSEN(2)
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4-2
SPIXCON1: SPIX CONTROL REGISTER 1
U-0
—
U-0
—
R/W-0
DISSCK
R/W-0
CKP
R/W-0
MSTEN
R/W-0
W = Writable bit
‘1’ = Bit is set
R/W-0
DISSDO
R/W-0
SPRE<2:0>(3)
R/W-0
MODE16
R/W-0
R/W-0
SMP
R/W-0
CKE(1)
bit 8
R/W-0
R/W-0
PPRE<1:0>(3)
bit 0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
DISSCK: Disable SCKx Pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled, pin functions as I/O
0 = Internal SPI clock is enabled
DISSDO: Disable SDOx Pin bit
1 = SDOx pin is not used by the module; pin functions as I/O
0 = SDOx pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
SMP: SPIx Data Input Sample Phase bit
Master mode:
1 = Input data is sampled at end of data output time
0 = Input data is sampled at middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
CKE: SPIx Clock Edge Select bit(1)
1 = Serial output data changes on transition from active clock state to idle clock state (refer to bit 6)
0 = Serial output data changes on transition from idle clock state to active clock state (refer to bit 6)
SSEN: Slave Select Enable bit (Slave mode)(2)
1 = SSx pin is used for Slave mode
0 = SSx pin is not used by module. Pin is controlled by port function
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level; active state is a low level
0 = Idle state for clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
SPRE<2:0>: Secondary Prescale bits (Master mode)(3)
111 = Secondary prescale 1:1
110 = Secondary prescale 2:1
•
•
•
bit 1-0
Note 1:
2:
3:
000 = Secondary prescale 8:1
PPRE<1:0>: Primary Prescale bits (Master mode)(3)
11 = Primary prescale 1:1
10 = Primary prescale 4:1
01 = Primary prescale 16:1
00 = Primary prescale 64:1
The CKE bit is not used in Framed SPI modes. Program this bit to ‘0’ for Framed SPI modes (FRMEN = 1).
This bit must be cleared when FRMEN = 1.
Do not set both Primary and Secondary prescalers to the value of 1:1.
DS70657E-page 270
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 18-3:
SPIXCON2: SPIX CONTROL REGISTER 2
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
U-0
U-0
FRMEN
SPIFSD
FRMPOL
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
—
—
—
—
—
—
FRMDLY
SPIBEN
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
FRMEN: Framed SPIx Support bit
1 = Framed SPIx support is enabled (SSx pin used as frame sync pulse input/output)
0 = Framed SPIx support is disabled
bit 14
SPIFSD: Frame Sync Pulse Direction Control bit
1 = Frame sync pulse input (slave)
0 = Frame sync pulse output (master)
bit 13
FRMPOL: Frame Sync Pulse Polarity bit
1 = Frame sync pulse is active-high
0 = Frame sync pulse is active-low
bit 12-2
Unimplemented: Read as ‘0’
bit 1
FRMDLY: Frame Sync Pulse Edge Select bit
1 = Frame sync pulse coincides with first bit clock
0 = Frame sync pulse precedes first bit clock
bit 0
SPIBEN: Enhanced Buffer Enable bit
1 = Enhanced Buffer is enabled
0 = Enhanced Buffer is disabled (Standard mode)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 271
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 272
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
19.0
INTER-INTEGRATED
CIRCUIT™ (I2C™)
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 19. “Inter-Integrated Circuit™ (I2C™)” (DS70330) of
the “dsPIC33E/PIC24E Family Reference Manual”, which is available from the
Microchip
web
site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
© 2011-2012 Microchip Technology Inc.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X family of devices
contain two Inter-Integrated Circuit (I2C) modules: I2C1
and I2C2.
The I2C module provides complete hardware support
for both Slave and Multi-Master modes of the I2C serial
communication standard, with a 16-bit interface.
The I2C module has a 2-pin interface:
• The SCLx pin is clock.
• The SDAx pin is data.
The I2C module offers the following key features:
• I2C interface supporting both Master and Slave
modes of operation.
• I2C Slave mode supports 7 and 10-bit address.
• I2C Master mode supports 7 and 10-bit address.
• I2C port allows bidirectional transfers between
master and slaves.
• Serial clock synchronization for I2C port can be
used as a handshake mechanism to suspend and
resume serial transfer (SCLREL control).
• I2C supports multi-master operation, detects bus
collision and arbitrates accordingly.
• Intelligent Platform Management Interface (IPMI)
support
• System Management Bus (SMBus) support
Preliminary
DS70657E-page 273
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 19-1:
I2C™ BLOCK DIAGRAM (X = 1 OR 2)
Internal
Data Bus
I2CxRCV
SCLx/ASCLx
Read
Shift
Clock
I2CxRSR
LSb
SDAx/ASDAx
Address Match
Match Detect
Write
I2CxMSK
Write
Read
I2CxADD
Read
Start and Stop
Bit Detect
Write
Start and Stop
Bit Generation
Control Logic
I2CxSTAT
Collision
Detect
Read
Write
I2CxCON
Acknowledge
Generation
Read
Clock
Stretching
Write
I2CxTRN
LSb
Read
Shift Clock
Reload
Control
Write
BRG Down Counter
I2CxBRG
Read
FP/2
DS70657E-page 274
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
19.1
I2C Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
19.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 19. “Inter-Integrated Circuit (I2C)”
(DS70330)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 275
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
19.2
I2C Control Registers
REGISTER 19-1:
I2CxCON: I2Cx CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-1 HC
R/W-0
R/W-0
R/W-0
R/W-0
I2CEN
—
I2CSIDL
SCLREL
IPMIEN(1)
A10M
DISSLW
SMEN
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0 HC
R/W-0 HC
R/W-0 HC
R/W-0 HC
R/W-0 HC
GCEN
STREN
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
HS = Set in hardware
HC = Cleared in hardware
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
I2CEN: I2Cx Enable bit
1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins
0 = Disables the I2Cx module. All I2C™ pins are controlled by port functions
bit 14
Unimplemented: Read as ‘0’
bit 13
I2CSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters an Idle mode
0 = Continue module operation in Idle mode
bit 12
SCLREL: SCLx Release Control bit (when operating as I2C slave)
1 = Release SCLx clock
0 = Hold SCLx clock low (clock stretch)
If STREN = 1:
Bit is R/W (i.e., software can write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear
at beginning of every slave data byte transmission. Hardware clear at end of every slave address byte
reception. Hardware clear at end of every slave data byte reception.
If STREN = 0:
Bit is R/S (i.e., software can only write ‘1’ to release clock). Hardware clear at beginning of every slave
data byte transmission. Hardware clear at the end of every slave address byte reception.
bit 11
IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit(1)
1 = IPMI mode is enabled; all addresses Acknowledged
0 = IPMI mode disabled
bit 10
A10M: 10-bit Slave Address bit
1 = I2CxADD is a 10-bit slave address
0 = I2CxADD is a 7-bit slave address
bit 9
DISSLW: Disable Slew Rate Control bit
1 = Slew rate control disabled
0 = Slew rate control enabled
bit 8
SMEN: SMBus Input Levels bit
1 = Enable I/O pin thresholds compliant with SMBus specification
0 = Disable SMBus input thresholds
bit 7
GCEN: General Call Enable bit (when operating as I2C slave)
1 = Enable interrupt when a general call address is received in the I2CxRSR
(module is enabled for reception)
0 = General call address disabled
Note 1:
When performing Master operations, ensure that the IPMIEN bit is ‘0’.
DS70657E-page 276
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 19-1:
I2CxCON: I2Cx CONTROL REGISTER (CONTINUED)
bit 6
STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave)
Used in conjunction with SCLREL bit.
1 = Enable software or receive clock stretching
0 = Disable software or receive clock stretching
bit 5
ACKDT: Acknowledge Data bit (when operating as I2C master, applicable during master receive)
Value that is transmitted when the software initiates an Acknowledge sequence.
1 = Send NACK during Acknowledge
0 = Send ACK during Acknowledge
bit 4
ACKEN: Acknowledge Sequence Enable bit
(when operating as I2C master, applicable during master receive)
1 = Initiate Acknowledge sequence on SDAx and SCLx pins and transmit ACKDT data bit.
Hardware clear at end of master Acknowledge sequence.
0 = Acknowledge sequence not in progress
bit 3
RCEN: Receive Enable bit (when operating as I2C master)
1 = Enables Receive mode for I2C. Hardware clear at end of eighth bit of master receive data byte.
0 = Receive sequence not in progress
bit 2
PEN: Stop Condition Enable bit (when operating as I2C master)
1 = Initiate Stop condition on SDAx and SCLx pins. Hardware clear at end of master Stop sequence.
0 = Stop condition not in progress
bit 1
RSEN: Repeated Start Condition Enable bit (when operating as I2C master)
1 = Initiate Repeated Start condition on SDAx and SCLx pins. Hardware clear at end of
master Repeated Start sequence.
0 = Repeated Start condition not in progress
bit 0
SEN: Start Condition Enable bit (when operating as I2C master)
1 = Initiate Start condition on SDAx and SCLx pins. Hardware clear at end of master Start sequence.
0 = Start condition not in progress
Note 1:
When performing Master operations, ensure that the IPMIEN bit is ‘0’.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 277
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 19-2:
I2CxSTAT: I2Cx STATUS REGISTER
R-0 HSC
R-0 HSC
U-0
U-0
U-0
R/C-0 HS
R-0 HSC
R-0 HSC
ACKSTAT
TRSTAT
—
—
—
BCL
GCSTAT
ADD10
bit 15
bit 8
R/C-0 HS
R/C-0 HS
R-0 HSC
R/C-0 HSC
R/C-0 HSC
R-0 HSC
R-0 HSC
R-0 HSC
IWCOL
I2COV
D_A
P
S
R_W
RBF
TBF
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
HS = Set in hardware
HSC = Hardware set/cleared
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ACKSTAT: Acknowledge Status bit
(when operating as I2C™ master, applicable to master transmit operation)
1 = NACK received from slave
0 = ACK received from slave
Hardware set or clear at end of slave Acknowledge.
bit 14
TRSTAT: Transmit Status bit (when operating as I2C master, applicable to master transmit operation)
1 = Master transmit is in progress (8 bits + ACK)
0 = Master transmit is not in progress
Hardware set at beginning of master transmission. Hardware clear at end of slave Acknowledge.
bit 13-11
Unimplemented: Read as ‘0’
bit 10
BCL: Master Bus Collision Detect bit
1 = A bus collision has been detected during a master operation
0 = No collision
Hardware set at detection of bus collision.
bit 9
GCSTAT: General Call Status bit
1 = General call address was received
0 = General call address was not received
Hardware set when address matches general call address. Hardware clear at Stop detection.
bit 8
ADD10: 10-bit Address Status bit
1 = 10-bit address was matched
0 = 10-bit address was not matched
Hardware set at match of 2nd byte of matched 10-bit address. Hardware clear at Stop detection.
bit 7
IWCOL: Write Collision Detect bit
1 = An attempt to write the I2CxTRN register failed because the I2C module is busy
0 = No collision
Hardware set at occurrence of write to I2CxTRN while busy (cleared by software).
bit 6
I2COV: Receive Overflow Flag bit
1 = A byte was received while the I2CxRCV register is still holding the previous byte
0 = No overflow
Hardware set at attempt to transfer I2CxRSR to I2CxRCV (cleared by software).
bit 5
D_A: Data/Address bit (when operating as I2C slave)
1 = Indicates that the last byte received was data
0 = Indicates that the last byte received was device address
Hardware clear at device address match. Hardware set by reception of slave byte.
bit 4
P: Stop bit
1 = Indicates that a Stop bit has been detected last
0 = Stop bit was not detected last
Hardware set or clear when Start, Repeated Start or Stop detected.
DS70657E-page 278
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 19-2:
I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED)
bit 3
S: Start bit
1 = Indicates that a Start (or Repeated Start) bit has been detected last
0 = Start bit was not detected last
Hardware set or clear when Start, Repeated Start or Stop detected.
bit 2
R_W: Read/Write Information bit (when operating as I2C slave)
1 = Read – indicates data transfer is output from slave
0 = Write – indicates data transfer is input to slave
Hardware set or clear after reception of I 2C device address byte.
bit 1
RBF: Receive Buffer Full Status bit
1 = Receive complete, I2CxRCV is full
0 = Receive not complete, I2CxRCV is empty
Hardware set when I2CxRCV is written with received byte. Hardware clear when software
reads I2CxRCV.
bit 0
TBF: Transmit Buffer Full Status bit
1 = Transmit in progress, I2CxTRN is full
0 = Transmit complete, I2CxTRN is empty
Hardware set when software writes I2CxTRN. Hardware clear at completion of data transmission.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 279
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 19-3:
I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-0
—
—
—
—
—
—
AMSK9
AMSK8
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
AMSK7
AMSK6
AMSK5
AMSK4
AMSK3
AMSK2
AMSK1
AMSK0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-10
Unimplemented: Read as ‘0’
bit 9-0
AMSKx: Mask for Address bit x Select bit
For 10-bit Address:
1 = Enable masking for bit Ax of incoming message address; bit match is not required in this position
0 = Disable masking for bit Ax; bit match is required in this position
For 7-bit Address (I2CxMSK<6:0> only):
1 = Enable masking for bit Ax + 1 of incoming message address; bit match is not required in this
position
0 = Disable masking for bit Ax + 1; bit match is required in this position
DS70657E-page 280
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
20.0
UNIVERSAL ASYNCHRONOUS
RECEIVER TRANSMITTER
(UART)
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 17. “UART”
(DS70582) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X family of devices
contain two UART modules.
The Universal Asynchronous Receiver Transmitter
(UART) module is one of the serial I/O modules
available
in
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X device family. The UART is a full-duplex
asynchronous system that can communicate with
peripheral devices, such as personal computers, LIN,
RS-232 and RS-485 interfaces. The module also
supports a hardware flow control option with the UxCTS
and UxRTS pins and also includes an IrDA® encoder
and decoder.
Note:
The primary features of the UART module are:
• Full-Duplex, 8- or 9-bit Data Transmission through
the UxTX and UxRX pins
• Even, Odd or No Parity Options (for 8-bit data)
• One or two stop bits
• Hardware flow control option with UxCTS and
UxRTS pins
• Fully integrated Baud Rate Generator with 16-bit
prescaler
• Baud rates ranging from 4.375 Mbps to 67 bps at
16x mode at 70 MIPS
• Baud rates ranging from 17.5 Mbps to 267 bps at
4x mode at 70 MIPS
• 4-deep First-In First-Out (FIFO) Transmit Data
buffer
• 4-deep FIFO Receive Data buffer
• Parity, framing and buffer overrun error detection
• Support for 9-bit mode with Address Detect
(9th bit = 1)
• Transmit and Receive interrupts
• A separate interrupt for all UART error conditions
• Loopback mode for diagnostic support
• Support for Sync and Break characters
• Support for automatic baud rate detection
• IrDA® encoder and decoder logic
• 16x baud clock output for IrDA® support
A simplified block diagram of the UART module is
shown in Figure 20-1. The UART module consists of
these key hardware elements:
• Baud Rate Generator
• Asynchronous Transmitter
• Asynchronous Receiver
Hardware flow control using UxRTS and
UxCTS is not available on all pin count
devices. See the “Pin Diagrams” section
for availability.
FIGURE 20-1:
UART SIMPLIFIED BLOCK DIAGRAM
Baud Rate Generator
IrDA®
Hardware Flow Control
UxRTS/BCLKx
UxCTS
UxRX
UART Receiver
UxTX
UART Transmitter
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 281
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
20.1
1.
2.
UART Helpful Tips
20.2
In multi-node direct-connect UART networks,
UART
receive
inputs
react
to
the
complementary logic level defined by the
URXINV bit (UxMODE<4>), which defines the
idle state, the default of which is logic high, (i.e.,
URXINV = 0). Because remote devices do not
initialize at the same time, it is likely that one of
the devices, because the RX line is floating, will
trigger a start bit detection and will cause the
first byte received after the device has been initialized to be invalid. To avoid this situation, the
user should use a pull-up or pull-down resistor
on the RX pin depending on the value of the
URXINV bit.
a) If URXINV = 0, use a pull-up resistor on the
RX pin.
b) If URXINV = 1, use a pull-down resistor on
the RX pin.
The first character received on a wake-up from
Sleep mode caused by activity on the UxRX pin
of the UART module will be invalid. In Sleep
mode, peripheral clocks are disabled. By the
time the oscillator system has restarted and
stabilized from Sleep mode, the baud rate bit
sampling clock relative to the incoming UxRX bit
timing is no longer synchronized, resulting in the
first character being invalid. This is to be
expected.
DS70657E-page 282
UART Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
20.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 17. “UART” (DS70582)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
20.3
UART Control Registers
REGISTER 20-1:
UxMODE: UARTx MODE REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
U-0
UARTEN(1)
—
USIDL
IREN(2)
RTSMD
—
R/W-0
R/W-0
UEN<1:0>
bit 15
bit 8
R/W-0 HC
R/W-0
R/W-0 HC
R/W-0
R/W-0
WAKE
LPBACK
ABAUD
URXINV
BRGH
R/W-0
R/W-0
PDSEL<1:0>
R/W-0
STSEL
bit 7
bit 0
Legend:
HC = Hardware cleared
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
UARTEN: UARTx Enable bit
1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>
0 = UARTx is disabled; all UARTx pins are controlled by PORT latches; UARTx power consumption
minimal
bit 14
Unimplemented: Read as ‘0’
bit 13
USIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12
IREN: IrDA® Encoder and Decoder Enable bit(2)
1 = IrDA encoder and decoder enabled
0 = IrDA encoder and decoder disabled
bit 11
RTSMD: Mode Selection for UxRTS Pin bit
1 = UxRTS pin in Simplex mode
0 = UxRTS pin in Flow Control mode
bit 10
Unimplemented: Read as ‘0’
bit 9-8
UEN<1:0>: UARTx Pin Enable bits
11 = UxTX, UxRX and BCLKx pins are enabled and used; UxCTS pin controlled by PORT latches(3)
10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used(4)
01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin controlled by PORT latches(4)
00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLKx pins controlled by
PORT latches
bit 7
WAKE: Wake-up on Start bit Detect During Sleep Mode Enable bit
1 = UARTx continues to sample the UxRX pin; interrupt generated on falling edge; bit cleared
in hardware on following rising edge
0 = No wake-up enabled
bit 6
LPBACK: UARTx Loopback Mode Select bit
1 = Enable Loopback mode
0 = Loopback mode is disabled
Note 1:
2:
3:
4:
Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for information on enabling the UART module for receive or transmit operation.
This feature is only available for the 16x BRG mode (BRGH = 0).
This feature is only available on 44-pin and 64-pin devices.
This feature is only available on 64-pin devices.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 283
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 20-1:
UxMODE: UARTx MODE REGISTER (CONTINUED)
bit 5
ABAUD: Auto-Baud Enable bit
1 = Enable baud rate measurement on the next character – requires reception of a Sync field (55h)
before other data; cleared in hardware upon completion
0 = Baud rate measurement disabled or completed
bit 4
URXINV: Receive Polarity Inversion bit
1 = UxRX Idle state is ‘0’
0 = UxRX Idle state is ‘1’
bit 3
BRGH: High Baud Rate Enable bit
1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode)
0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode)
bit 2-1
PDSEL<1:0>: Parity and Data Selection bits
11 = 9-bit data, no parity
10 = 8-bit data, odd parity
01 = 8-bit data, even parity
00 = 8-bit data, no parity
bit 0
STSEL: Stop Bit Selection bit
1 = Two Stop bits
0 = One Stop bit
Note 1:
2:
3:
4:
Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for information on enabling the UART module for receive or transmit operation.
This feature is only available for the 16x BRG mode (BRGH = 0).
This feature is only available on 44-pin and 64-pin devices.
This feature is only available on 64-pin devices.
DS70657E-page 284
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 20-2:
UxSTA: UARTx STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
R/W-0 HC
R/W-0
R-0
R-1
UTXISEL1
UTXINV
UTXISEL0
—
UTXBRK
UTXEN(1)
UTXBF
TRMT
bit 15
bit 8
R/W-0
R/W-0
URXISEL<1:0>
R/W-0
R-1
R-0
R-0
R/C-0
R-0
ADDEN
RIDLE
PERR
FERR
OERR
URXDA
bit 7
bit 0
Legend:
HC = Hardware cleared
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15,13
UTXISEL<1:0>: Transmission Interrupt Mode Selection bits
11 = Reserved; do not use
10 = Interrupt when a character is transferred to the Transmit Shift Register, and as a result, the
transmit buffer becomes empty
01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit
operations are completed
00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is
at least one character open in the transmit buffer)
bit 14
UTXINV: Transmit Polarity Inversion bit
If IREN = 0:
1 = UxTX Idle state is ‘0’
0 = UxTX Idle state is ‘1’
If IREN = 1:
1 = IrDA encoded UxTX Idle state is ‘1’
0 = IrDA encoded UxTX Idle state is ‘0’
bit 12
Unimplemented: Read as ‘0’
bit 11
UTXBRK: Transmit Break bit
1 = Send Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit;
cleared by hardware upon completion
0 = Sync Break transmission disabled or completed
bit 10
UTXEN: Transmit Enable bit(1)
1 = Transmit enabled, UxTX pin controlled by UARTx
0 = Transmit disabled, any pending transmission is aborted and buffer is reset. UxTX pin controlled
by port.
bit 9
UTXBF: Transmit Buffer Full Status bit (read-only)
1 = Transmit buffer is full
0 = Transmit buffer is not full, at least one more character can be written
bit 8
TRMT: Transmit Shift Register Empty bit (read-only)
1 = Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)
0 = Transmit Shift Register is not empty, a transmission is in progress or queued
bit 7-6
URXISEL<1:0>: Receive Interrupt Mode Selection bits
11 = Interrupt is set on UxRSR transfer making the receive buffer full (i.e., has 4 data characters)
10 = Interrupt is set on UxRSR transfer making the receive buffer 3/4 full (i.e., has 3 data characters)
0x = Interrupt is set when any character is received and transferred from the UxRSR to the receive
buffer. Receive buffer has one or more characters.
Note 1:
Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for
information on enabling the UART module for transmit operation.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 285
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 20-2:
UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED)
bit 5
ADDEN: Address Character Detect bit (bit 8 of received data = 1)
1 = Address Detect mode enabled. If 9-bit mode is not selected, this does not take effect.
0 = Address Detect mode disabled
bit 4
RIDLE: Receiver Idle bit (read-only)
1 = Receiver is Idle
0 = Receiver is active
bit 3
PERR: Parity Error Status bit (read-only)
1 = Parity error has been detected for the current character (character at the top of the receive FIFO)
0 = Parity error has not been detected
bit 2
FERR: Framing Error Status bit (read-only)
1 = Framing error has been detected for the current character (character at the top of the receive
FIFO)
0 = Framing error has not been detected
bit 1
OERR: Receive Buffer Overrun Error Status bit (read/clear only)
1 = Receive buffer has overflowed
0 = Receive buffer has not overflowed. Clearing a previously set OERR bit (1 →0 transition) resets
the receiver buffer and the UxRSR to the empty state.
bit 0
URXDA: Receive Buffer Data Available bit (read-only)
1 = Receive buffer has data, at least one more character can be read
0 = Receive buffer is empty
Note 1:
Refer to Section 17. “UART” (DS70582) in the “dsPIC33E/PIC24E Family Reference Manual” for
information on enabling the UART module for transmit operation.
DS70657E-page 286
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
21.0
ENHANCED CAN (ECAN™)
MODULE (dsPIC33EPXXXGP/
MC50X DEVICES ONLY)
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 21. “Enhanced
Controller Area Network (ECAN™)”
(DS70353) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
21.1
Overview
The Enhanced Controller Area Network (ECAN)
module is a serial interface, useful for communicating with other CAN modules or microcontroller
devices. This interface/protocol was designed to
allow communications within noisy environments.
The dsPIC33EPXXXGP/MC50X devices contain one
ECAN module.
The ECAN module is a communication controller
implementing the CAN 2.0 A/B protocol, as defined in
the BOSCH CAN specification. The module supports
CAN 1.2, CAN 2.0A, CAN 2.0B Passive and CAN 2.0B
Active versions of the protocol. The module implementation is a full CAN system. The CAN specification is
not covered within this data sheet. The reader can refer
to the BOSCH CAN specification for further details.
© 2011-2012 Microchip Technology Inc.
The ECAN module features are as follows:
• Implementation of the CAN protocol, CAN 1.2,
CAN 2.0A and CAN 2.0B
• Standard and extended data frames
• 0-8 bytes data length
• Programmable bit rate up to 1 Mbit/sec
• Automatic response to remote transmission
requests
• Up to eight transmit buffers with application specified prioritization and abort capability (each buffer
can contain up to 8 bytes of data)
• Up to 32 receive buffers (each buffer can contain
up to 8 bytes of data)
• Up to 16 full (standard/extended identifier)
acceptance filters
• Three full acceptance filter masks
• DeviceNet™ addressing support
• Programmable wake-up functionality with
integrated low-pass filter
• Programmable Loopback mode supports self-test
operation
• Signaling via interrupt capabilities for all CAN
receiver and transmitter error states
• Programmable clock source
• Programmable link to Input Capture module (IC2)
for time-stamping and network synchronization
• Low-power Sleep and Idle mode
The CAN bus module consists of a protocol engine and
message buffering/control. The CAN protocol engine
handles all functions for receiving and transmitting
messages on the CAN bus. Messages are transmitted
by first loading the appropriate data registers. Status
and errors can be checked by reading the appropriate
registers. Any message detected on the CAN bus is
checked for errors and then matched against filters to
see if it should be received and stored in one of the
receive registers.
Preliminary
DS70657E-page 287
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 21-1:
ECAN™ MODULE BLOCK DIAGRAM
RxF15 Filter
RxF14 Filter
RxF13 Filter
RxF12 Filter
DMA Controller
RxF11 Filter
RxF10 Filter
RxF9 Filter
RxF8 Filter
TRB7 Tx/Rx Buffer Control Register
RxF7 Filter
TRB6 Tx/Rx Buffer Control Register
RxF6 Filter
TRB5 Tx/Rx Buffer Control Register
RxF5 Filter
TRB4 Tx/Rx Buffer Control Register
RxF4 Filter
TRB3 Tx/Rx Buffer Control Register
RxF3 Filter
TRB2 Tx/Rx Buffer Control Register
RxF2 Filter
RxM2 Mask
TRB1 Tx/Rx Buffer Control Register
RxF1 Filter
RxM1 Mask
TRB0 Tx/Rx Buffer Control Register
RxF0 Filter
RxM0 Mask
Transmit Byte
Sequencer
Message Assembly
Buffer
Control
Configuration
Logic
CAN Protocol
Engine
CPU
Bus
Interrupts
CiTx
DS70657E-page 288
CiRx
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
21.2
Modes of Operation
21.3
The ECAN module can operate in one of several
operation modes selected by the user. These modes
include:
•
•
•
•
•
•
Initialization mode
Disable mode
Normal Operation mode
Listen Only mode
Listen All Messages mode
Loopback mode
© 2011-2012 Microchip Technology Inc.
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
Modes are requested by setting the REQOP<2:0> bits
(CiCTRL1<10:8>). Entry into a mode is Acknowledged
by
monitoring
the
OPMODE<2:0>
bits
(CiCTRL1<7:5>). The module does not change the
mode and the OPMODE bits until a change in mode is
acceptable, generally during bus Idle time, which is
defined as at least 11 consecutive recessive bits.
ECAN Resources
21.3.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 21. “Enhanced Controller Area Network
(ECAN™)” (DS70353)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
Preliminary
DS70657E-page 289
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
21.4
ECAN Control Registers
REGISTER 21-1:
U-0
—
bit 15
R-1
CiCTRL1: ECAN™ CONTROL REGISTER 1
U-0
—
R/W-0
CSIDL
R/W-0
ABAT
R/W-0
CANCKS
R/W-1
R-0
OPMODE<2:0>
Legend:
R = Readable bit
-n = Value at POR
bit 12
bit 11
bit 10-8
bit 7-5
bit 4
bit 3
bit 2-1
bit 0
R/W-0
bit 8
R-0
U-0
—
R/W-0
CANCAP
U-0
—
bit 7
bit 15-14
bit 13
R/W-0
REQOP<2:0>
U-0
—
R/W-0
WIN
bit 0
C = Writable bit, but only ‘0’ can be written to clear the bit r = Bit is Reserved
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
CSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
ABAT: Abort All Pending Transmissions bit
1 = Signal all transmit buffers to abort transmission
0 = Module will clear this bit when all transmissions are aborted
CANCKS: ECAN Module Clock (FCAN) Source Select bit
1 = FCAN is equal to 2 * FP
0 = FCAN is equal to FP
REQOP<2:0>: Request Operation Mode bits
111 = Set Listen All Messages mode
110 = Reserved
101 = Reserved
100 = Set Configuration mode
011 = Set Listen Only Mode
010 = Set Loopback mode
001 = Set Disable mode
000 = Set Normal Operation mode
OPMODE<2:0>: Operation Mode bits
111 = Module is in Listen All Messages mode
110 = Reserved
101 = Reserved
100 = Module is in Configuration mode
011 = Module is in Listen Only mode
010 = Module is in Loopback mode
001 = Module is in Disable mode
000 = Module is in Normal Operation mode
Unimplemented: Read as ‘0’
CANCAP: CAN Message Receive Timer Capture Event Enable bit
1 = Enable input capture based on CAN message receive
0 = Disable CAN capture
Unimplemented: Read as ‘0’
WIN: SFR Map Window Select bit
1 = Use filter window
0 = Use buffer window
DS70657E-page 290
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-2:
CiCTRL2: ECAN™ CONTROL REGISTER 2
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
U-0
—
R-0
R-0
R-0
DNCNT<4:0>
R-0
R-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-5
bit 4-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
DNCNT<4:0>: DeviceNet™ Filter Bit Number bits
10010-11111 = Invalid selection
10001 = Compare up to data byte 3, bit 6 with EID<17>
•
•
•
00001 = Compare up to data byte 1, bit 7 with EID<0>
00000 = Do not compare data bytes
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 291
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-3:
CiVEC: ECAN™ INTERRUPT CODE REGISTER
U-0
—
bit 15
U-0
—
U-0
—
R-1
U-0
—
R-0
R-0
R-0
FILHIT<4:0>
R-0
bit 8
R-0
R-0
R-0
ICODE<6:0>
R-0
R-0
bit 7
bit 7
bit 6-0
R-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12-8
R-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
FILHIT<4:0>: Filter Hit Number bits
10000-11111 = Reserved
01111 = Filter 15
•
•
•
00001 = Filter 1
00000 = Filter 0
Unimplemented: Read as ‘0’
ICODE<6:0>: Interrupt Flag Code bits
1000101-1111111 = Reserved
1000100 = FIFO almost full interrupt
1000011 = Receiver overflow interrupt
1000010 = Wake-up interrupt
1000001 = Error interrupt
1000000 = No interrupt
•
•
•
0010000-0111111 = Reserved
0001111 = RB15 buffer Interrupt
•
•
•
0001001 = RB9 buffer interrupt
0001000 = RB8 buffer interrupt
0000111 = TRB7 buffer interrupt
0000110 = TRB6 buffer interrupt
0000101 = TRB5 buffer interrupt
0000100 = TRB4 buffer interrupt
0000011 = TRB3 buffer interrupt
0000010 = TRB2 buffer interrupt
0000001 = TRB1 buffer interrupt
0000000 = TRB0 Buffer interrupt
DS70657E-page 292
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-4:
R/W-0
CiFCTRL: ECAN™ FIFO CONTROL REGISTER
R/W-0
DMABS<2:0>
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
FSA<4:0>
R/W-0
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12-5
bit 4-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
DMABS<2:0>: DMA Buffer Size bits
111 = Reserved
110 = 32 buffers in RAM
101 = 24 buffers in RAM
100 = 16 buffers in RAM
011 = 12 buffers in RAM
010 = 8 buffers in RAM
001 = 6 buffers in RAM
000 = 4 buffers in RAM
Unimplemented: Read as ‘0’
FSA<4:0>: FIFO Area Starts with Buffer bits
11111 = Read buffer RB31
11110 = Read buffer RB30
•
•
•
00001 = Tx/Rx buffer TRB1
00000 = Tx/Rx buffer TRB0
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 293
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-5:
CiFIFO: ECAN™ FIFO STATUS REGISTER
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
R-0
R-0
R-0
R-0
FBP<5:0>
R-0
bit 8
R-0
R-0
R-0
R-0
FNRB<5:0>
R-0
bit 7
bit 7-6
bit 5-0
R-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13-8
R-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
FBP<5:0>: FIFO Buffer Pointer bits
011111 = RB31 buffer
011110 = RB30 buffer
•
•
•
000001 = TRB1 buffer
000000 = TRB0 buffer
Unimplemented: Read as ‘0’
FNRB<5:0>: FIFO Next Read Buffer Pointer bits
011111 = RB31 buffer
011110 = RB30 buffer
•
•
•
000001 = TRB1 buffer
000000 = TRB0 buffer
DS70657E-page 294
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-6:
CiINTF: ECAN™ INTERRUPT FLAG REGISTER
U-0
—
bit 15
U-0
—
R-0
TXBO
R-0
TXBP
R-0
RXBP
R-0
TXWAR
R-0
RXWAR
R-0
EWARN
bit 8
R/C-0
IVRIF
bit 7
R/C-0
WAKIF
R/C-0
ERRIF
U-0
—
R/C-0
FIFOIF
R/C-0
RBOVIF
R/C-0
RBIF
R/C-0
TBIF
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
TXBO: Transmitter in Error State Bus Off bit
1 = Transmitter is in Bus Off state
0 = Transmitter is not in Bus Off state
TXBP: Transmitter in Error State Bus Passive bit
1 = Transmitter is in Bus Passive state
0 = Transmitter is not in Bus Passive state
RXBP: Receiver in Error State Bus Passive bit
1 = Receiver is in Bus Passive state
0 = Receiver is not in Bus Passive state
TXWAR: Transmitter in Error State Warning bit
1 = Transmitter is in Error Warning state
0 = Transmitter is not in Error Warning state
RXWAR: Receiver in Error State Warning bit
1 = Receiver is in Error Warning state
0 = Receiver is not in Error Warning state
EWARN: Transmitter or Receiver in Error State Warning bit
1 = Transmitter or Receiver is in Error State Warning state
0 = Transmitter or Receiver is not in Error State Warning state
IVRIF: Invalid Message Interrupt Flag bit
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
WAKIF: Bus Wake-up Activity Interrupt Flag bit
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
ERRIF: Error Interrupt Flag bit (multiple sources in CiINTF<13:8> register)
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
Unimplemented: Read as ‘0’
FIFOIF: FIFO Almost Full Interrupt Flag bit
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
RBOVIF: RX Buffer Overflow Interrupt Flag bit
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
RBIF: RX Buffer Interrupt Flag bit
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
TBIF: TX Buffer Interrupt Flag bit
1 = Interrupt Request has occurred
0 = Interrupt Request has not occurred
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 295
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-7:
U-0
—
bit 15
U-0
—
R/W-0
WAKIE
Legend:
R = Readable bit
-n = Value at POR
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
R/W-0
IVRIE
bit 7
bit 15-8
bit 7
CiINTE: ECAN™ INTERRUPT ENABLE REGISTER
R/W-0
ERRIE
R/W-0
—
R/W-0
FIFOIE
R/W-0
RBOVIE
R/W-0
RBIE
R/W-0
TBIE
bit 0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
IVRIE: Invalid Message Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
WAKIE: Bus Wake-up Activity Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
ERRIE: Error Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
Unimplemented: Read as ‘0’
FIFOIE: FIFO Almost Full Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
RBOVIE: RX Buffer Overflow Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
RBIE: RX Buffer Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
TBIE: TX Buffer Interrupt Enable bit
1 = Interrupt Request Enabled
0 = Interrupt Request not enabled
DS70657E-page 296
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-8:
R-0
CiEC: ECAN™ TRANSMIT/RECEIVE ERROR COUNT REGISTER
R-0
R-0
R-0
R-0
TERRCNT<7:0>
R-0
R-0
R-0
bit 15
bit 8
R-0
R-0
R-0
R-0
R-0
RERRCNT<7:0>
R-0
R-0
R-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
TERRCNT<7:0>: Transmit Error Count bits
RERRCNT<7:0>: Receive Error Count bits
REGISTER 21-9:
U-0
—
bit 15
CiCFG1: ECAN™ BAUD RATE CONFIGURATION REGISTER 1
U-0
—
Legend:
R = Readable bit
-n = Value at POR
bit 5-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 8
R/W-0
R/W-0
SJW<1:0>
bit 7
bit 15-8
bit 7-6
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
BRP<5:0>
R/W-0
R/W-0
bit 0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
SJW<1:0>: Synchronization Jump Width bits
11 = Length is 4 x TQ
10 = Length is 3 x TQ
01 = Length is 2 x TQ
00 = Length is 1 x TQ
BRP<5:0>: Baud Rate Prescaler bits
11 1111 = TQ = 2 x 64 x 1/FCAN
•
•
•
00 0010 = TQ = 2 x 3 x 1/FCAN
00 0001 = TQ = 2 x 2 x 1/FCAN
00 0000 = TQ = 2 x 1 x 1/FCAN
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 297
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-10: CiCFG2: ECAN™ BAUD RATE CONFIGURATION REGISTER 2
U-0
—
bit 15
R/W-x
WAKFIL
R/W-x
SAM
bit 7
bit 6
bit 5-3
bit 2-0
U-0
—
R/W-x
R/W-x
SEG2PH<2:0>
R/W-x
R/W-x
R/W-x
SEG1PH<2:0>
R/W-x
R/W-x
R/W-x
PRSEG<2:0>
R/W-x
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 13-11
bit 10-8
U-0
—
bit 8
R/W-x
SEG2PHTS
bit 7
bit 15
bit 14
U-0
—
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
WAKFIL: Select CAN bus Line Filter for Wake-up bit
1 = Use CAN bus line filter for wake-up
0 = CAN bus line filter is not used for wake-up
Unimplemented: Read as ‘0’
SEG2PH<2:0>: Phase Segment 2 bits
111 = Length is 8 x TQ
•
•
•
000 = Length is 1 x TQ
SEG2PHTS: Phase Segment 2 Time Select bit
1 = Freely programmable
0 = Maximum of SEG1PH bits or Information Processing Time (IPT), whichever is greater
SAM: Sample of the CAN bus Line bit
1 = Bus line is sampled three times at the sample point
0 = Bus line is sampled once at the sample point
SEG1PH<2:0>: Phase Segment 1 bits
111 = Length is 8 x TQ
•
•
•
000 = Length is 1 x TQ
PRSEG<2:0>: Propagation Time Segment bits
111 = Length is 8 x TQ
•
•
•
000 = Length is 1 x TQ
DS70657E-page 298
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-11: CiFEN1: ECAN™ ACCEPTANCE FILTER ENABLE REGISTER 1
R/W-1
FLTEN15
bit 15
R/W-1
FLTEN14
R/W-1
FLTEN13
R/W-1
FLTEN12
R/W-1
FLTEN11
R/W-1
FLTEN10
R/W-1
FLTEN9
R/W-1
FLTEN8
bit 8
R/W-1
FLTEN7
bit 7
R/W-1
FLTEN6
R/W-1
FLTEN5
R/W-1
FLTEN4
R/W-1
FLTEN3
R/W-1
FLTEN2
R/W-1
FLTEN1
R/W-1
FLTEN0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
FLTENn: Enable Filter n to Accept Messages bits
1 = Enable Filter n
0 = Disable Filter n
REGISTER 21-12: CiBUFPNT1: ECAN™ FILTER 0-3 BUFFER POINTER REGISTER 1
R/W-0
R/W-0
R/W-0
F3BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F2BP<3:0>
R/W-0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
F1BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F0BP<3:0>
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-12
bit 11-8
bit 7-4
bit 3-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
F3BP<3:0>: RX Buffer mask for Filter 3 bits
1111 = Filter hits received in RX FIFO buffer
1110 = Filter hits received in RX Buffer 14
•
•
•
0001 = Filter hits received in RX Buffer 1
0000 = Filter hits received in RX Buffer 0
F2BP<3:0>: RX Buffer mask for Filter 2 bits (same values as bit 15-12)
F1BP<3:0>: RX Buffer mask for Filter 1 bits (same values as bit 15-12)
F0BP<3:0>: RX Buffer mask for Filter 0 bits (same values as bit 15-12)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 299
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-13: CiBUFPNT2: ECAN™ FILTER 4-7 BUFFER POINTER REGISTER 2
R/W-0
R/W-0
R/W-0
F7BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F6BP<3:0>
R/W-0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
F5BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F4BP<3:0>
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-12
bit 11-8
bit 7-4
bit 3-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
F7BP<3:0>: RX Buffer mask for Filter 7 bits
1111 = Filter hits received in RX FIFO buffer
1110 = Filter hits received in RX Buffer 14
•
•
•
0001 = Filter hits received in RX Buffer 1
0000 = Filter hits received in RX Buffer 0
F6BP<3:0>: RX Buffer mask for Filter 6 bits (same values as bit 15-12)
F5BP<3:0>: RX Buffer mask for Filter 5 bits (same values as bit 15-12)
F4BP<3:0>: RX Buffer mask for Filter 4 bits (same values as bit 15-12)
REGISTER 21-14: CiBUFPNT3: ECAN™ FILTER 8-11 BUFFER POINTER REGISTER 3
R/W-0
R/W-0
R/W-0
F11BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F10BP<3:0>
R/W-0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
F9BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F8BP<3:0>
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-12
bit 11-8
bit 7-4
bit 3-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
F11BP<3:0>: RX Buffer mask for Filter 11 bits
1111 = Filter hits received in RX FIFO buffer
1110 = Filter hits received in RX Buffer 14
•
•
•
0001 = Filter hits received in RX Buffer 1
0000 = Filter hits received in RX Buffer 0
F10BP<3:0>: RX Buffer mask for Filter 10 bits (same values as bit 15-12)
F9BP<3:0>: RX Buffer mask for Filter 9 bits (same values as bit 15-12)
F8BP<3:0>: RX Buffer mask for Filter 8 bits (same values as bit 15-12)
DS70657E-page 300
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-15: CiBUFPNT4: ECAN™ FILTER 12-15 BUFFER POINTER REGISTER 4
R/W-0
R/W-0
R/W-0
F15BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F14BP<3:0>
R/W-0
bit 15
bit 8
R/W-0
R/W-0
R/W-0
F13BP<3:0>
R/W-0
R/W-0
R/W-0
R/W-0
F12BP<3:0>
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-12
bit 11-8
bit 7-4
bit 3-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
F15BP<3:0>: RX Buffer mask for Filter 15 bits
1111 = Filter hits received in RX FIFO buffer
1110 = Filter hits received in RX Buffer 14
•
•
•
0001 = Filter hits received in RX Buffer 1
0000 = Filter hits received in RX Buffer 0
F14BP<3:0>: RX Buffer mask for Filter 14 bits (same values as bit 15-12)
F13BP<3:0>: RX Buffer mask for Filter 13 bits (same values as bit 15-12)
F12BP<3:0>: RX Buffer mask for Filter 12 bits (same values as bit 15-12)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 301
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-16: CiRXFnSID: ECAN™ ACCEPTANCE FILTER STANDARD IDENTIFIER REGISTER
n (n = 0-15)
R/W-x
SID10
bit 15
R/W-x
SID9
R/W-x
SID8
R/W-x
SID7
R/W-x
SID6
R/W-x
SID5
R/W-x
SID4
R/W-x
SID3
bit 8
R/W-x
SID2
bit 7
R/W-x
SID1
R/W-x
SID0
U-0
—
R/W-x
EXIDE
U-0
—
R/W-x
EID17
R/W-x
EID16
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-5
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 4
bit 3
SID<10:0>: Standard Identifier bits
1 = Message address bit SIDx must be ‘1’ to match filter
0 = Message address bit SIDx must be ‘0’ to match filter
Unimplemented: Read as ‘0’
EXIDE: Extended Identifier Enable bit
If MIDE = 1:
1 = Match only messages with extended identifier addresses
0 = Match only messages with standard identifier addresses
bit 2
bit 1-0
If MIDE = 0:
Ignore EXIDE bit.
Unimplemented: Read as ‘0’
EID<17:16>: Extended Identifier bits
1 = Message address bit EIDx must be ‘1’ to match filter
0 = Message address bit EIDx must be ‘0’ to match filter
DS70657E-page 302
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-17: CiRXFnEID: ECAN™ ACCEPTANCE FILTER EXTENDED IDENTIFIER REGISTER
n (n = 0-15)
R/W-x
EID15
bit 15
R/W-x
EID14
R/W-x
EID13
R/W-x
EID12
R/W-x
EID11
R/W-x
EID10
R/W-x
EID9
R/W-x
EID8
bit 8
R/W-x
EID7
bit 7
R/W-x
EID6
R/W-x
EID5
R/W-x
EID4
R/W-x
EID3
R/W-x
EID2
R/W-x
EID1
R/W-x
EID0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
EID<15:0>: Extended Identifier bits
1 = Message address bit EIDx must be ‘1’ to match filter
0 = Message address bit EIDx must be ‘0’ to match filter
REGISTER 21-18: CiFMSKSEL1: ECAN™ FILTER 7-0 MASK SELECTION REGISTER
R/W-0
R/W-0
F7MSK<1:0>
bit 15
R/W-0
R/W-0
F6MSK<1:0>
R/W-0
R/W-0
F5MSK<1:0>
R/W-0
R/W-0
F4MSK<1:0>
bit 8
R/W-0
R/W-0
F3MSK<1:0>
bit 7
R/W-0
R/W-0
F2MSK<1:0>
R/W-0
R/W-0
F1MSK<1:0>
R/W-0
R/W-0
F0MSK<1:0>
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13-12
bit 11-10
bit 9-8
bit 7-6
bit 5-4
bit 3-2
bit 1-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
F7MSK<1:0>: Mask Source for Filter 7 bit
11 = Reserved
10 = Acceptance Mask 2 registers contain mask
01 = Acceptance Mask 1 registers contain mask
00 = Acceptance Mask 0 registers contain mask
F6MSK<1:0>: Mask Source for Filter 6 bit (same values as bit 15-14)
F5MSK<1:0>: Mask Source for Filter 5 bit (same values as bit 15-14)
F4MSK<1:0>: Mask Source for Filter 4 bit (same values as bit 15-14)
F3MSK<1:0>: Mask Source for Filter 3 bit (same values as bit 15-14)
F2MSK<1:0>: Mask Source for Filter 2 bit (same values as bit 15-14)
F1MSK<1:0>: Mask Source for Filter 1 bit (same values as bit 15-14)
F0MSK<1:0>: Mask Source for Filter 0 bit (same values as bit 15-14)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 303
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-19: CiFMSKSEL2: ECAN™ FILTER 15-8 MASK SELECTION REGISTER
R/W-0
R/W-0
F15MSK<1:0>
bit 15
R/W-0
R/W-0
F14MSK<1:0>
R/W-0
R/W-0
F13MSK<1:0>
R/W-0
R/W-0
F12MSK<1:0>
bit 8
R/W-0
R/W-0
F11MSK<1:0>
bit 7
R/W-0
R/W-0
F10MSK<1:0>
R/W-0
R/W-0
F9MSK<1:0>
R/W-0
R/W-0
F8MSK<1:0>
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13-12
bit 11-10
bit 9-8
bit 7-6
bit 5-4
bit 3-2
bit 1-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
F15MSK<1:0>: Mask Source for Filter 15 bit
11 = Reserved
10 = Acceptance Mask 2 registers contain mask
01 = Acceptance Mask 1 registers contain mask
00 = Acceptance Mask 0 registers contain mask
F14MSK<1:0>: Mask Source for Filter 14 bit (same values as bit 15-14)
F13MSK<1:0>: Mask Source for Filter 13 bit (same values as bit 15-14)
F12MSK<1:0>: Mask Source for Filter 12 bit (same values as bit 15-14)
F11MSK<1:0>: Mask Source for Filter 11 bit (same values as bit 15-14)
F10MSK<1:0>: Mask Source for Filter 10 bit (same values as bit 15-14)
F9MSK<1:0>: Mask Source for Filter 9 bit (same values as bit 15-14)
F8MSK<1:0>: Mask Source for Filter 8 bit (same values as bit 15-14)
DS70657E-page 304
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-20: CiRXMnSID: ECAN™ ACCEPTANCE FILTER MASK STANDARD IDENTIFIER
REGISTER n (n = 0-2)
R/W-x
SID10
bit 15
R/W-x
SID9
R/W-x
SID8
R/W-x
SID7
R/W-x
SID6
R/W-x
SID5
R/W-x
SID4
R/W-x
SID3
bit 8
R/W-x
SID2
bit 7
R/W-x
SID1
R/W-x
SID0
U-0
—
R/W-x
MIDE
U-0
—
R/W-x
EID17
R/W-x
EID16
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-5
bit 4
bit 3
bit 2
bit 1-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
SID<10:0>: Standard Identifier bits
1 = Include bit SIDx in filter comparison
0 = Bit SIDx is don’t care in filter comparison
Unimplemented: Read as ‘0’
MIDE: Identifier Receive Mode bit
1 = Match only message types (standard or extended address) that correspond to EXIDE bit in filter
0 = Match either standard or extended address message if filters match
(i.e., if (Filter SID) = (Message SID) or if (Filter SID/EID) = (Message SID/EID))
Unimplemented: Read as ‘0’
EID<17:16>: Extended Identifier bits
1 = Include bit EIDx in filter comparison
0 = Bit EIDx is don’t care in filter comparison
REGISTER 21-21: CiRXMnEID: ECAN™ ACCEPTANCE FILTER MASK EXTENDED IDENTIFIER
REGISTER n (n = 0-2)
R/W-x
EID15
bit 15
R/W-x
EID14
R/W-x
EID13
R/W-x
EID12
R/W-x
EID11
R/W-x
EID10
R/W-x
EID9
R/W-x
EID8
bit 8
R/W-x
EID7
bit 7
R/W-x
EID6
R/W-x
EID5
R/W-x
EID4
R/W-x
EID3
R/W-x
EID2
R/W-x
EID1
R/W-x
EID0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
EID<15:0>: Extended Identifier bits
1 = Include bit EIDx in filter comparison
0 = Bit EIDx is don’t care in filter comparison
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 305
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-22: CiRXFUL1: ECAN™ RECEIVE BUFFER FULL REGISTER 1
R/C-0
RXFUL15
bit 15
R/C-0
RXFUL14
R/C-0
RXFUL13
R/C-0
RXFUL12
R/C-0
RXFUL11
R/C-0
RXFUL10
R/C-0
RXFUL9
R/C-0
RXFUL8
bit 8
R/C-0
RXFUL7
bit 7
R/C-0
RXFUL6
R/C-0
RXFUL5
R/C-0
RXFUL4
R/C-0
RXFUL3
R/C-0
RXFUL2
R/C-0
RXFUL1
R/C-0
RXFUL0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
RXFUL<15:0>: Receive Buffer n Full bits
1 = Buffer is full (set by module)
0 = Buffer is empty (cleared by user software)
REGISTER 21-23: CiRXFUL2: ECAN™ RECEIVE BUFFER FULL REGISTER 2
R/C-0
RXFUL31
bit 15
R/C-0
RXFUL30
R/C-0
RXFUL29
R/C-0
RXFUL28
R/C-0
RXFUL27
R/C-0
RXFUL26
R/C-0
RXFUL25
R/C-0
RXFUL24
bit 8
R/C-0
RXFUL23
bit 7
R/C-0
RXFUL22
R/C-0
RXFUL21
R/C-0
RXFUL20
R/C-0
RXFUL19
R/C-0
RXFUL18
R/C-0
RXFUL17
R/C-0
RXFUL16
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
RXFUL<31:16>: Receive Buffer n Full bits
1 = Buffer is full (set by module)
0 = Buffer is empty (cleared by user software)
DS70657E-page 306
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-24: CiRXOVF1: ECAN™ RECEIVE BUFFER OVERFLOW REGISTER 1
R/C-0
RXOVF15
bit 15
R/C-0
RXOVF14
R/C-0
RXOVF13
R/C-0
RXOVF12
R/C-0
RXOVF11
R/C-0
RXOVF10
R/C-0
RXOVF9
R/C-0
RXOVF8
bit 8
R/C-0
RXOVF7
bit 7
R/C-0
RXOVF6
R/C-0
RXOVF5
R/C-0
RXOVF4
R/C-0
RXOVF3
R/C-0
RXOVF2
R/C-0
RXOVF1
R/C-0
RXOVF0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
RXOVF<15:0>: Receive Buffer n Overflow bits
1 = Module attempted to write to a full buffer (set by module)
0 = No overflow condition (cleared by user software)
REGISTER 21-25: CiRXOVF2: ECAN™ RECEIVE BUFFER OVERFLOW REGISTER 2
R/C-0
RXOVF31
bit 15
R/C-0
RXOVF30
R/C-0
RXOVF29
R/C-0
RXOVF28
R/C-0
RXOVF27
R/C-0
RXOVF26
R/C-0
RXOVF25
R/C-0
RXOVF24
bit 8
R/C-0
RXOVF23
bit 7
R/C-0
RXOVF22
R/C-0
RXOVF21
R/C-0
RXOVF20
R/C-0
RXOVF19
R/C-0
RXOVF18
R/C-0
RXOVF17
R/C-0
RXOVF16
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
RXOVF<31:16>: Receive Buffer n Overflow bits
1 = Module attempted to write to a full buffer (set by module)
0 = No overflow condition (cleared by user software)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 307
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 21-26: CiTRmnCON: ECAN™ Tx/Rx BUFFER m CONTROL REGISTER
(m = 0,2,4,6; n = 1,3,5,7)
R/W-0
TXENn
bit 15
R-0
TXABTn
R/W-0
TXENm
bit 7
R-0
TXABTm(1)
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1-0
Note 1:
Note:
R-0
TXLARBn
R-0
TXERRn
R-0
R-0
TXLARBm(1) TXERRm(1)
R/W-0
TXREQn
R/W-0
RTRENn
R/W-0
R/W-0
TXnPRI<1:0>
bit 8
R/W-0
TXREQm
R/W-0
RTRENm
R/W-0
R/W-0
TXmPRI<1:0>
bit 0
C = Writable bit, but only ‘0’ can be written to clear the bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
See Definition for Bits 7-0, Controls Buffer n
TXENm: TX/RX Buffer Selection bit
1 = Buffer TRBn is a transmit buffer
0 = Buffer TRBn is a receive buffer
TXABTm: Message Aborted bit(1)
1 = Message was aborted
0 = Message completed transmission successfully
TXLARBm: Message Lost Arbitration bit(1)
1 = Message lost arbitration while being sent
0 = Message did not lose arbitration while being sent
TXERRm: Error Detected During Transmission bit(1)
1 = A bus error occurred while the message was being sent
0 = A bus error did not occur while the message was being sent
TXREQm: Message Send Request bit
1 = Requests that a message be sent. The bit automatically clears when the message is successfully
sent.
0 = Clearing the bit to ‘0’ while set requests a message abort.
RTRENm: Auto-Remote Transmit Enable bit
1 = When a remote transmit is received, TXREQ will be set
0 = When a remote transmit is received, TXREQ will be unaffected
TXmPRI<1:0>: Message Transmission Priority bits
11 = Highest message priority
10 = High intermediate message priority
01 = Low intermediate message priority
00 = Lowest message priority
This bit is cleared when TXREQ is set.
The buffers, SID, EID, DLC, Data Field and Receive Status registers are located in DMA RAM.
DS70657E-page 308
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
21.5
ECAN Message Buffers
ECAN Message Buffers are part of RAM Memory. They
are not ECAN Special Function Registers. The user
application must directly write into the RAM area that is
configured for ECAN Message Buffers. The location
and size of the buffer area is defined by the user
application.
BUFFER 21-1:
ECAN™ MESSAGE BUFFER WORD 0
U-0
—
bit 15
U-0
—
U-0
—
R/W-x
SID10
R/W-x
SID9
R/W-x
SID8
R/W-x
SID7
R/W-x
SID6
bit 8
R/W-x
SID5
bit 7
R/W-x
SID4
R/W-x
SID3
R/W-x
SID2
R/W-x
SID1
R/W-x
SID0
R/W-x
SRR
R/W-x
IDE
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12-2
bit 1
bit 0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
SID<10:0>: Standard Identifier bits
SRR: Substitute Remote Request bit
When TXIDE = 0:
1 = Message will request remote transmission
0 = Normal message
When TXIDE = 1:
The SRR bit must be set to ‘1’
IDE: Extended Identifier bit
1 = Message will transmit extended identifier
0 = Message will transmit standard identifier
BUFFER 21-2:
ECAN™ MESSAGE BUFFER WORD 1
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
R/W-x
EID17
R/W-x
EID16
R/W-x
EID15
R/W-x
EID14
bit 8
R/W-x
EID13
bit 7
R/W-x
EID12
R/W-x
EID11
R/W-x
EID10
R/W-x
EID9
R/W-x
EID8
R/W-x
EID7
R/W-x
EID6
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-12
bit 11-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
EID<17:6>: Extended Identifier bits
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 309
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
(
BUFFER 21-3:
R/W-x
EID5
bit 15
U-x
—
ECAN™ MESSAGE BUFFER WORD 2
R/W-x
EID4
R/W-x
EID3
R/W-x
EID2
R/W-x
EID1
R/W-x
EID0
R/W-x
RTR
R/W-x
RB1
bit 8
U-x
—
U-x
—
R/W-x
RB0
R/W-x
DLC3
R/W-x
DLC2
R/W-x
DLC1
R/W-x
DLC0
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-10
bit 9
bit 8
bit 7-5
bit 4
bit 3-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
EID<5:0>: Extended Identifier bits
RTR: Remote Transmission Request bit
When TXIDE = 1:
1 = Message will request remote transmission
0 = Normal message
When TXIDE = 0:
The RTR bit is ignored.
RB1: Reserved Bit 1
User must set this bit to ‘0’ per CAN protocol.
Unimplemented: Read as ‘0’
RB0: Reserved Bit 0
User must set this bit to ‘0’ per CAN protocol.
DLC<3:0>: Data Length Code bits
BUFFER 21-4:
R/W-x
ECAN™ MESSAGE BUFFER WORD 3
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 1
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Byte 1<15:8>: ECAN™ Message byte 0
Byte 0<7:0>: ECAN Message byte 1
DS70657E-page 310
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
BUFFER 21-5:
R/W-x
ECAN™ MESSAGE BUFFER WORD 4
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 3
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 2
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Byte 3<15:8>: ECAN™ Message byte 3
Byte 2<7:0>: ECAN Message byte 2
BUFFER 21-6:
R/W-x
ECAN™ MESSAGE BUFFER WORD 5
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 5
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 4
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Byte 5<15:8>: ECAN™ Message byte 5
Byte 4<7:0>: ECAN Message byte 4
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 311
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
BUFFER 21-7:
R/W-x
ECAN™ MESSAGE BUFFER WORD 6
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 7
bit 15
bit 8
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
Byte 6
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Byte 7<15:8>: ECAN™ Message byte 7
Byte 6<7:0>: ECAN Message byte 6
BUFFER 21-8:
ECAN™ MESSAGE BUFFER WORD 7
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
R/W-x
R/W-x
R/W-x
FILHIT<4:0>(1)
R/W-x
R/W-x
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12-8
bit 7-0
Note 1:
U-0
—
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
FILHIT<4:0>: Filter Hit Code bits(1)
Encodes number of filter that resulted in writing this buffer.
Unimplemented: Read as ‘0’
Only written by module for receive buffers, unused for transmit buffers.
DS70657E-page 312
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
22.0
CHARGE TIME
MEASUREMENT UNIT (CTMU)
The Charge Time Measurement Unit is a flexible analog module that provides accurate differential time
measurement between pulse sources, as well as
asynchronous pulse generation. Its key features
include:
Note 1: This data sheet summarizes the features of the dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X
family
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 33. “Charge
Time Measurement Unit (CTMU)”
(DS70661) in the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available on the Microchip web site
(www.microchip.com).
•
•
•
•
•
•
Four edge input trigger sources
Polarity control for each edge source
Control of edge sequence
Control of response to edges
Precise time measurement resolution of 1 ns
Accurate current source suitable for capacitive
measurement
• On-chip temperature measurement using a
built-in diode
Together with other on-chip analog modules, the CTMU
can be used to precisely measure time, measure
capacitance, measure relative changes in capacitance
or generate output pulses that are independent of the
system clock.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 22-1:
The CTMU module is ideal for interfacing with capacitive-based sensors.The CTMU is controlled through
two registers: CTMUCON and CTMUICON.
CTMUCON enables the module and controls edge
source selection, edge source polarity selection and
edge sequencing. The CTMUICON register controls
the selection and trim of the current source.
CTMU BLOCK DIAGRAM
CTMUCON1 or CTMUCON2
CTMUICON
ITRIM<5:0>
IRNG<1:0>
Current Source
Edge
Control
Logic
CTED1
CTED2
EDG1STAT
EDG2STAT
TGEN
Current
Control
CTMU
Control
Logic
Analog-to-Digital
Trigger
Pulse
Generator
CTPLS
Timer1
OC1
IC1
CMP1
CTMUI to ADC
CTMUP
CTMU TEMP
CTMU
Temperature
Sensor
C1IN1CDelay
CMP1
External capacitor
for pulse generation
Current Control Selection
TGEN
EDG1STAT, EDG2STAT
CTMU TEMP
0
EDG1STAT = EDG2STAT
CTMUI to ADC
0
EDG1STAT ≠ EDG2STAT
CTMUP
1
EDG1STAT ≠ EDG2STAT
No Connect
1
EDG1STAT = EDG2STAT
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 313
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
22.1
CTMU Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
22.1.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 33. “Charge Time Measurement Unit
(CTMU)” (DS70661)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
DS70657E-page 314
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
22.2
CTMU Control Registers
REGISTER 22-1:
CTMUCON1: CTMU CONTROL REGISTER 1
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CTMUEN
—
CTMUSIDL
TGEN
EDGEN
EDGSEQEN
IDISSEN(1)
CTTRIG
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
CTMUSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
bit 11
EDGEN: Edge Enable bit
1 = Hardware modules are used to trigger edges (TMRx, CTEDx, etc.)
0 = Software is used to trigger edges (manual set of EDGxSTAT)
bit 10
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
bit 9
IDISSEN: Analog Current Source Control bit(1)
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
bit 8
CTTRIG: ADC Trigger Control bit
1 = CTMU triggers ADC start of conversion
0 = CTMU does not trigger ADC start of conversion
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
x = Bit is unknown
The ADC module Sample and Hold capacitor is not automatically discharged between sample/conversion
cycles. Software using the ADC as part of a capacitance measurement, must discharge the ADC capacitor
before conducting the measurement. The IDISSEN bit, when set to ‘1’, performs this function. The ADC
must be sampling while the IDISSEN bit is active to connect the discharge sink to the capacitor array.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 315
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 22-2:
CTMUCON2: CTMU CONTROL REGISTER 2
R/W-0
R/W-0
EDG1MOD
EDG1POL
R/W-0
R/W-0
R/W-0
R/W-0
EDG1SEL<3:0>
R/W-0
R/W-0
EDG2STAT
EDG1STAT
bit 15
bit 8
R/W-0
R/W-0
EDG2MOD
EDG2POL
R/W-0
R/W-0
R/W-0
R/W-0
U-0
U-0
—
—
EDG2SEL<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
EDG1MOD: Edge 1 Edge Sampling Mode Selection bit
1 = Edge 1 is edge sensitive
0 = Edge 1 is level sensitive
bit 14
EDG1POL: Edge 1 Polarity Select bit
1 = Edge 1 programmed for a positive edge response
0 = Edge 1 programmed for a negative edge response
bit 13-10
EDG1SEL<3:0>: Edge 1 Source Select bits
1xxx = Reserved
01xx = Reserved
0011 = CTED1 pin
0010 = CTED2 pin
0001 = OC1 module
0000 = Timer1 module
bit 9
EDG2STAT: Edge 2 Status bit
Indicates the status of Edge 2 and can be written to control the edge source.
1 = Edge 2 has occurred
0 = Edge 2 has not occurred
bit 8
EDG1STAT: Edge 1 Status bit
Indicates the status of Edge 1 and can be written to control the edge source.
1 = Edge 1 has occurred
0 = Edge 1 has not occurred
bit 7
EDG2MOD: Edge 2 Edge Sampling Mode Selection bit
1 = Edge 2 is edge sensitive
0 = Edge 2 is level sensitive
bit 6
EDG2POL: Edge 2 Polarity Select bit
1 = Edge 2 programmed for a positive edge response
0 = Edge 2 programmed for a negative edge response
bit 5-2
EDG2SEL<3:0>: Edge 2 Source Select bits
1111 = Reserved
01xx = Reserved
0100 = CMP1 module
0011 = CTED2 pin
0010 = CTED1 pin
0001 = OC1 module
0000 = IC1 module
bit 1-0
Unimplemented: Read as ‘0’
DS70657E-page 316
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 22-3:
R/W-0
CTMUICON: CTMU CURRENT CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ITRIM<5:0>
R/W-0
IRNG<1:0>
bit 15
bit 8
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-10
ITRIM<5:0>: Current Source Trim bits
011111 = Maximum positive change from nominal current +62%
011110 = Maximum positive change from nominal current +60%
•
•
•
000010 = Minimum positive change from nominal current +4%
000001 = Minimum positive change from nominal current +2%
000000 = Nominal current output specified by IRNG<1:0>
111111 = Minimum negative change from nominal current -2%
111110 = Minimum negative change from nominal current -4%
•
•
•
100010 = Maximum negative change from nominal current -60%
100001 = Maximum negative change from nominal current -62%
bit 9-8
IRNG<1:0>: Current Source Range Select bits
11 = 100 × Base Current(2)
10 = 10 × Base Current(2)
01 = Base Current Level(2)
00 = 1000 × Base Current(1,2)
bit 7-0
Unimplemented: Read as ‘0’
Note 1:
2:
x = Bit is unknown
This current range is not available to be used with the internal temperature measurement diode.
Refer to the CTMU Current Source Specifications (Table 30-55) in Section 30.0 “Electrical
Characteristics” for the current range selection values.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 317
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 318
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
23.0
10-BIT/12-BIT ANALOG-TODIGITAL CONVERTER (ADC)
23.1
23.1.1
Note 1: This data sheet summarizes the features of the dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 16. “Analog-toDigital Converter (ADC)” (DS70621)
of the “dsPIC33E/PIC24E Family
Reference Manual”, which is available
from
the
Microchip
web
site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices have one
ADC module. The ADC module supports up to 16
analog input channels.
On ADC1, the AD12B bit (AD1CON1<10>) allows each
of the ADC modules to be configured by the user as
either a 10-bit, 4-Sample and Hold (S&H) ADC (default
configuration) or a 12-bit, 1-S&H ADC.
Note:
The ADC module needs to be disabled
before modifying the AD12B bit.
Key Features
10-BIT ADC CONFIGURATION
The 10-bit ADC configuration has the following key
features:
•
•
•
•
•
•
•
•
•
•
•
•
•
Successive Approximation (SAR) conversion
Conversion speeds of up to 1.1 Msps
Up to 16 analog input pins
Connections to three internal op amps
Connections to the Charge Time Measurement Unit
(CTMU) and temperature measurement diode
Channel selection and triggering can be controlled by the Peripheral Trigger Generator (PTG)
External voltage reference input pins
Simultaneous sampling of:
- Up to four analog input pins
- Three op amp outputs
- Combinations of analog inputs and op amp
outputs
Automatic Channel Scan mode
Selectable conversion trigger source
Selectable Buffer Fill modes
Four result alignment options (signed/unsigned,
fractional/integer)
Operation during CPU Sleep and Idle modes
23.1.2
12-BIT ADC CONFIGURATION
The 12-bit ADC configuration supports all the features
listed above, with the exception of the following:
• In the 12-bit configuration, conversion speeds of
up to 500 ksps are supported
• There is only one S&H amplifier in the 12-bit
configuration; therefore, simultaneous sampling
of multiple channels is not supported.
Depending on the particular device pinout, the ADC
can have up to 16 analog input pins, designated AN0
through AN15. These analog inputs are shared with
op amp inputs and outputs, comparator inputs, and
external voltage references. When op amp/comparator
functionality is enabled or an external voltage reference
is used, the analog input that shares that pin is no longer available. The actual number of analog input pins,
op amps and external voltage reference input
configuration depends on the specific device.
A block diagram of the ADC module is shown in
Figure 23-1. Figure 23-2 provides a diagram of the
ADC conversion clock period.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 319
ADC MODULE BLOCK DIAGRAM WITH CONNECTION OPTIONS FOR ANx PINS AND OP AMPS
This diagram depicts all of the available
ADC connection options to the four S&H
amplifiers, which are designated: CH0,
CH1, CH2, and CH3.
The ANx analog pins or op amp outputs
are connected to the CH0-CH3 amplifiers
through the multiplexers controlled by the
SFR Control bits, CH0Sx, CHONx,
CH123Sx and CH123Nx.
00000
AN0-ANx
OA1-OA3
CTMU TEMP
OPEN
Channel Scan
From CTMU
Current Source (CTMUI)
11111
+
CH0
–
CH0Sx
VREFL
1
CH0SA<4:0>
(3)
0
CSCNA
S&H0
A
CH0SB<4:0>(3)
0
1
AN0/OA2OUT/RA0
B
CH0NA(3)
A
CH0NB(3)
B
CH0Sx
CH0Nx
CH0Nx
PGEC1/AN4/C1IN1+/RPI34/RB2
PGED1/AN5/C1IN1-/RP35/RB3
0
++
OPMODE
CMP1
/OA1
––
OA1
PGEC3/VREF+/AN3/OA1OUT/RPI33/CTED1/RB1
+
CH1
–
1
CH123SA
A
CH123SB
B
CH123x
VREFL
0x
10
11
Preliminary
AN9/RPI27/RA11
CH123NA<2:0>
A
CH123NB<2:0>
B
+
S&H2
0
OPMODE
+
CH2
–
1
–
OA2
Alternate Input
(MUXA/MUXB)
Selection
ALTS
VREF+(1)
0x
AVDD
VREF-(1)
AVSS
10
11
AN10/RPI28/RA12
PGED3/VREF-/AN2/C2IN1-/SS1/RPI32/CTED2/RB0
CH123Nx
© 2011-2012 Microchip Technology Inc.
AN8/C3IN1+/U1RTS/BCLK1/RC2
+
AN7/C3IN1-/C4IN1-/RC1
–
OPMODE
S&H3
0
+
CH3
–
1
OA3
AN6/OA3OUT/C4IN1+/OCFB/RC0
VREFL
VCFG<2:0>
VREFH
VREFL
ADC1BUF0(4)
ADC1BUF1(4)
ADC1BUF2(4)
CH123Sx
0x
SAR ADC
10
11
CH123Nx
1:
2:
3:
4:
CH123Nx
CH123Sx
VREFL
Note
CH123Sx
CH123Nx
AN1/C2IN1+/RA1
AN11/C1IN2-/U1CTS/RC11
S&H1
VREF+, VREF- inputs can be multiplexed with other analog inputs.
Channels 1, 2 and 3 are not applicable for the 12-bit mode of operation.
These bits can be updated with Step commands from the PTG module. See Section 24.0 “Peripheral Trigger Generator (PTG) Module” for more information.
When ADDMAEN (ADxCON4<8>) = 1 enabling DMA, only ADCxBUF0 is used.
ADC1BUFE(4)
ADC1BUFF(4)
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 320
FIGURE 23-1:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 23-2:
ADC CONVERSION CLOCK PERIOD BLOCK DIAGRAM
AD1CON3<15>
ADC Internal
RC Clock(2)
1
TAD
AD1CON3<7:0>
0
6
TP(1)
ADC Conversion
Clock Multiplier
1, 2, 3, 4, 5,..., 256
Note 1: TP = 1/FP.
2: See the ADC electrical specifications in Section 30.0 “Electrical Characteristics” for the exact RC
clock value.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 321
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
23.2
1.
2.
3.
4.
ADC Helpful Tips
5.
The SMPI control bits in the ADxCON2 registers:
a) Determine when the ADC interrupt flag is
set and an interrupt is generated, if
enabled.
b) When the CSCNA bit in the ADxCON2 registers is set to ‘1’, this determines when the
ADC analog scan channel list defined in the
AD1CSSL/AD1CSSH registers starts over
from the beginning.
c) When the DMA peripheral is not used
(ADDMAEN = 0), this determines when the
ADC result buffer pointer to ADC1BUF0ADC1BUFF, gets reset back to the
beginning at ADC1BUF0.
d) When the DMA peripheral is used
(ADDMAEN = 1), this determines when the
DMA address pointer is incremented after a
sample/conversion operation. ADC1BUF0
is the only ADC buffer used in this mode.
The ADC result buffer pointer to
ADC1BUF0-ADC1BUFF gets reset back to
the beginning at ADC1BUF0. The DMA
address is incremented after completion of
every 32nd sample/conversion operation.
Conversion results are stored in the
ADC1BUF0 register for transfer to RAM
using DMA.
When the DMA module is disabled
(ADDMAEN = 0), the ADC has 16 result buffers.
ADC conversion results are stored sequentially
in ADC1BUF0-ADC1BUFF regardless of which
analog inputs are being used subject to the
SMPI bits and the condition described in 1c
above. There is no relationship between the
ANx input being measured and which ADC buffer
(ADC1BUF0-ADC1BUFF)
that
the
conversion results will be placed in.
When the DMA module is enabled
(ADDMAEN = 1), the ADC module has only 1
ADC result buffer, (i.e., ADC1BUF0), per ADC
peripheral and the ADC conversion result must
be read either by the CPU or DMA controller
before the next ADC conversion is complete to
avoid overwriting the previous value.
The DONE bit (ADxCON1<0>) is only cleared at
the start of each conversion and is set at the
completion of the conversion, but remains set
indefinitely even through the next sample phase
until the next conversion begins. If application
code is monitoring the DONE bit in any kind of
software loop, the user must consider this
behavior because the CPU code execution is
faster than the ADC. As a result, in manual sample mode, particularly where the users code is
setting the SAMP bit (ADxCON1<1>), the
DONE bit should also be cleared by the user
application just before setting the SAMP bit.
DS70657E-page 322
Enabling op amps, comparator inputs and external voltage references can limit the availability of
analog inputs (ANx pins). For example, when
Op amp 2 is enabled, the pins for AN0, AN1, and
AN2 are used by the op amp’s inputs and output.
This negates the usefulness of Alternate Input
mode since the MUXA selections uses AN0AN2. Carefully study the ADC block diagram to
determine the configuration that will best suit
your application. Configuration examples are
available in Section 16. “Analog-to-Digital
Converter (ADC)” (DS70621) in the
“dsPIC33E/PIC24E Family Reference Manual”.
23.3
ADC Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
23.3.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 16. “Analog-to-Digital Converter
(ADC)” (DS70621)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
23.4
ADC Control Registers
REGISTER 23-1:
R/W-0
ADON
bit 15
R/W-0
AD1CON1: ADC1 CONTROL REGISTER 1
U-0
—
R/W-0
ADSIDL
R/W-0
ADDMABM
U-0
—
R/W-0
AD12B
R/W-0
R/W-0
FORM<1:0>
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SSRCG
SIMSAM
ASAM
R/W-0
HC,HS
SAMP
SSRC<2:0>
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9-8
Note 1:
2:
3:
HC = Cleared by hardware
W = Writable bit
‘1’ = Bit is set
R/C-0
HC, HS
DONE(3)
bit 0
HS = Set by hardware
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
ADON: ADC Operating Mode bit
1 = ADC module is operating
0 = ADC is off
Unimplemented: Read as ‘0’
ADSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
ADDMABM: DMA Buffer Build Mode bit
1 = DMA buffers are written in the order of conversion. The module provides an address to the DMA
channel that is the same as the address used for the non-DMA stand-alone buffer.
0 = DMA buffers are written in Scatter/Gather mode. The module provides a Scatter/Gather address
to the DMA channel, based on the index of the analog input and the size of the DMA buffer.
Unimplemented: Read as ‘0’
AD12B: 10-bit or 12-bit Operation Mode bit
1 = 12-bit, 1-channel ADC operation
0 = 10-bit, 4-channel ADC operation
FORM<1:0>: Data Output Format bits
For 10-bit operation:
11 = Signed fractional (DOUT = sddd dddd dd00 0000, where s = .NOT.d<9>)
10 = Fractional (DOUT = dddd dddd dd00 0000)
01 = Signed integer (DOUT = ssss sssd dddd dddd, where s = .NOT.d<9>)
00 = Integer (DOUT = 0000 00dd dddd dddd)
For 12-bit operation:
11 = Signed fractional (DOUT = sddd dddd dddd 0000, where s = .NOT.d<11>)
10 = Fractional (DOUT = dddd dddd dddd 0000)
01 = Signed Integer (DOUT = ssss sddd dddd dddd, where s = .NOT.d<11>)
00 = Integer (DOUT = 0000 dddd dddd dddd)
See Section 24.0 “Peripheral Trigger Generator (PTG) Module” for information on this selection.
This setting is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
Do not clear the DONE bit in software if Auto-Sample is enabled (ASAM = 1).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 323
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-1:
bit 7-5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
2:
3:
AD1CON1: ADC1 CONTROL REGISTER 1 (CONTINUED)
SSRC<2:0>: Sample Clock Source Select bits
If SSRCG = 1:
111 = Reserved
110 = PTGO15 primary trigger compare ends sampling and starts conversion(1)
101 = PTGO14 primary trigger compare ends sampling and starts conversion(1)
100 = PTGO13 primary trigger compare ends sampling and starts conversion(1)
011 = PTGO12 primary trigger compare ends sampling and starts conversion(1)
010 = PWM Generator 3 primary trigger compare ends sampling and starts conversion(2)
001 = PWM Generator 2 primary trigger compare ends sampling and starts conversion(2)
000 = PWM Generator 1 primary trigger compare ends sampling and starts conversion(2)
If SSRCG = 0:
111 = Internal counter ends sampling and starts conversion (auto-convert)
110 = CTMU ends sampling and starts conversion
101 = Reserved
100 = Timer5 compare ends sampling and starts conversion
011 = PWM primary Special Event Trigger ends sampling and starts conversion(2)
010 = Timer3 compare ends sampling and starts conversion
001 = Active transition on the INT0 pin ends sampling and starts conversion
000 = Clearing the Sample bit (SAMP) ends sampling and starts conversion (Manual mode)
SSRCG: Sample Clock Source Group bit
See SSRC<2:0> for details.
SIMSAM: Simultaneous Sample Select bit (only applicable when CHPS<1:0> = 01 or 1x)
In 12-bit mode, (AD21B = 1), SIMSAM is unimplemented and is read as ‘0’
1 = Samples CH0, CH1, CH2, CH3 simultaneously (when CHPS<1:0> = 1x); or
Samples CH0 and CH1 simultaneously (when CHPS<1:0> = 01)
0 = Samples multiple channels individually in sequence
ASAM: ADC Sample Auto-Start bit
1 = Sampling begins immediately after last conversion. SAMP bit is auto-set.
0 = Sampling begins when SAMP bit is set
SAMP: ADC Sample Enable bit
1 = ADC Sample and Hold amplifiers are sampling
0 = ADC Sample and Hold amplifiers are holding
If ASAM = 0, software can write ‘1’ to begin sampling. Automatically set by hardware if ASAM = 1.
If SSRC = 000, software can write ‘0’ to end sampling and start conversion. If SSRC ≠ 000,
automatically cleared by hardware to end sampling and start conversion.
DONE: ADC Conversion Status bit(3)
1 = ADC conversion cycle is completed.
0 = ADC conversion not started or in progress
Automatically set by hardware when A/D conversion is complete. Software can write ‘0’ to clear DONE
status (software not allowed to write ‘1’). Clearing this bit does NOT affect any operation in progress.
Automatically cleared by hardware at start of a new conversion.
See Section 24.0 “Peripheral Trigger Generator (PTG) Module” for information on this selection.
This setting is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
Do not clear the DONE bit in software if Auto-Sample is enabled (ASAM = 1).
DS70657E-page 324
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-2:
R/W-0
AD1CON2: ADC1 CONTROL REGISTER 2
R/W-0
VCFG<2:0>
R/W-0
U-0
—
U-0
—
R/W-0
CSCNA
R/W-0
R/W-0
R/W-0
SMPI<4:0>
R/W-0
R/W-0
bit 15
R-0
BUFS
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 9-8
bit 7
bit 6-2
R/W-0
BUFM
R/W-0
ALTS
bit 0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
VCFG<2:0>: Converter Voltage Reference Configuration bits
Value
000
001
010
011
1xx
bit 12-11
bit 10
W = Writable bit
‘1’ = Bit is set
R/W-0
R/W-0
CHPS<1:0>
bit 8
VREFH
AVDD
External VREF+
AVDD
External VREF+
AVDD
VREFL
Avss
Avss
External VREFExternal VREFAvss
Unimplemented: Read as ‘0’
CSCNA: Input Scan Select bit
1 = Scan inputs for CH0+ during Sample MUXA
0 = Do not scan inputs
CHPS<1:0>: Channel Select bits
In 12-bit mode, (AD21B = 1), CHPS<1:0> is unimplemented and is read as ‘0’
1x = Converts CH0, CH1, CH2 and CH3
01 = Converts CH0 and CH1
00 = Converts CH0
BUFS: Buffer Fill Status bit (only valid when BUFM = 1)
1 = ADC is currently filling the second half of the buffer. The user application should access data in the
first half of the buffer
0 = ADC is currently filling the first half of the buffer. The user application should access data in the
second half of the buffer.
SMPI<4:0>: Increment Rate bits
When ADDMAEN = 0:
x1111 = Generates interrupt after completion of every 16th sample/conversion operation
x1110 = Generates interrupt after completion of every 15th sample/conversion operation
•
•
•
x0001 = Generates interrupt after completion of every 2nd sample/conversion operation
x0000 = Generates interrupt after completion of every sample/conversion operation
When ADDMAEN = 1:
11111 = Increments the DMA address after completion of every 32nd sample/conversion operation
11110 = Increments the DMA address after completion of every 31st sample/conversion operation
•
•
•
bit 1
bit 0
00001 = Increments the DMA address after completion of every 2nd sample/conversion operation
00000 = Increments the DMA address after completion of every sample/conversion operation
BUFM: Buffer Fill Mode Select bit
1 = Starts buffer filling the first half of the buffer on the first interrupt and the second half of the buffer
on next interrupt
0 = Always starts filling the buffer from the start address.
ALTS: Alternate Input Sample Mode Select bit
1 = Uses channel input selects for Sample MUXA on first sample and Sample MUXB on next sample
0 = Always uses channel input selects for Sample MUXA
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 325
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-3:
R/W-0
ADRC
bit 15
AD1CON3: ADC1 CONTROL REGISTER 3
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
SAMC<4:0>(1)
R/W-0
R/W-0
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCS<7:0>(2)
R/W-0
R/W-0
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-13
bit 12-8
bit 7-0
Note 1:
2:
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
ADRC: ADC Conversion Clock Source bit
1 = ADC Internal RC Clock
0 = Clock Derived From System Clock
Unimplemented: Read as ‘0’
SAMC<4:0>: Auto Sample Time bits(1)
11111 = 31 TAD
•
•
•
00001 = 1 TAD
00000 = 0 TAD
ADCS<7:0>: ADC Conversion Clock Select bits(2)
11111111 = TP · (ADCS<7:0> + 1) = TP ·256 = TAD
•
•
•
00000010 = TP · (ADCS<7:0> + 1) = TP ·3 = TAD
00000001 = TP · (ADCS<7:0> + 1) = TP ·2 = TAD
00000000 = TP · (ADCS<7:0> + 1) = TP ·1 = TAD
This bit is only used if AD1CON1<7:5> (SSRC<2:0>) = 111 and AD1CON1<4> (SSRCG) = 0.
This bit is not used if AD1CON3<15> (ADRC) = 1.
DS70657E-page 326
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-4:
AD1CON4: ADC1 CONTROL REGISTER 4
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
ADDMAEN
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
DMABL<2:0>
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-7
bit 8
bit 7-3
bit 2-0
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
ADDMAEN: ADC DMA Enable bit
1 = Conversion results stored in ADC1BUF0 register, for transfer to RAM using DMA
0 = Conversion results stored in ADC1BUF0 through ADC1BUFF registers; DMA will not be used
Unimplemented: Read as ‘0’
DMABL<2:0>: Selects Number of DMA Buffer Locations per Analog Input bits
111 = Allocates 128 words of buffer to each analog input
110 = Allocates 64 words of buffer to each analog input
101 = Allocates 32 words of buffer to each analog input
100 = Allocates 16 words of buffer to each analog input
011 = Allocates 8 words of buffer to each analog input
010 = Allocates 4 words of buffer to each analog input
001 = Allocates 2 words of buffer to each analog input
000 = Allocates 1 word of buffer to each analog input
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 327
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-5:
AD1CHS123: ADC1 INPUT CHANNEL 1, 2, 3 SELECT REGISTER
U-0
—
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
CH123NB<1:0>
R/W-0
CH123SB
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
CH123NA<1:0>
R/W-0
CH123SA
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-11
bit 10-9
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Unimplemented: Read as ‘0’
CH123NB<1:0>: Channel 1, 2, 3 Negative Input Select for Sample MUXB bits
In 12-bit mode, (AD21B = 1), CH123NB is unimplemented and is read as ‘0’
Value
11
10(1,2)
0x
bit 8
W = Writable bit
‘1’ = Bit is set
ADC Channel
CH1
CH2
CH3
AN9
AN10
AN11
OA3/AN6
AN7
AN8
VREFL
VREFL
VREFL
CH123SB: Channel 1, 2, 3 Positive Input Select for Sample MUXB bit
In 12-bit mode, (AD21B = 1), CH123SB is unimplemented and is read as ‘0’
Value
bit 7-3
bit 2-1
ADC Channel
CH1
CH2
CH3
1(2)
OA1/AN3
OA2/AN0
OA3/AN6
0(1,2)
OA2/AN0
AN1
AN2
Unimplemented: Read as ‘0’
CH123NA<1:0>: Channel 1, 2, 3 Negative Input Select for Sample MUXA bits
In 12-bit mode, (AD21B = 1), CH123NA is unimplemented and is read as ‘0’
Value
11
10(1,2)
0x
bit 0
ADC Channel
CH1
CH2
CH3
AN9
AN10
AN11
OA3/AN6
AN7
AN8
VREFL
VREFL
VREFL
CH123SA: Channel 1, 2, 3 Positive Input Select for Sample MUXA bit
In 12-bit mode, (AD21B = 1), CH123SA is unimplemented and is read as ‘0’
Value
Note 1:
2:
ADC Channel
CH1
CH2
CH3
1(2)
OA1/AN3
OA2/AN0
OA3/AN6
0(1,2)
OA2/AN0
AN1
AN2
AN0 through AN7 are repurposed when comparator and op amp functionality is enabled. See Figure 23-1
to determine how enabling a particular op amp or comparator affects selection choices for Channels 1, 2,
and 3.
If the Op amp/Comparator module is enabled (COE bit (CMxCON<14>) = 1) and the op amp is selected
(OPMODE bit (CMxCON<10>) = 1), the OAx input is used; otherwise, the ANx input is used.
DS70657E-page 328
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-6:
AD1CHS0: ADC1 INPUT CHANNEL 0 SELECT REGISTER
R/W-0
CH0NB
bit 15
U-0
—
R/W-0
CH0NA
bit 7
U-0
—
bit 14-13
bit 12-8
bit 7
bit 6-5
Note 1:
2:
3:
R/W-0
R/W-0
R/W-0
CH0SB<4:0>
R/W-0
R/W-0
bit 8
U-0
—
R/W-0
R/W-0
R/W-0
CH0SA<4:0>
R/W-0
R/W-0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
U-0
—
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
CH0NB: Channel 0 Negative Input Select for Sample MUXB bit
1 = Channel 0 negative input is AN1(1)
0 = Channel 0 negative input is VREFL
Unimplemented: Read as ‘0’
CH0SB<4:0>: Channel 0 Positive Input Select for Sample MUXB bits(1)
11111 = Open; use this selection with CTMU capacitive and time measurement
11110 = Channel 0 positive input is connected to CTMU temperature measurement diode
(CTMU TEMP)
11101 = Reserved
11100 = Reserved
11011 = Reserved
11010 = Channel 0 positive input is output of OA3/AN6(2)
11001 = Channel 0 positive input is output of OA2/AN0(2)
11000 = Channel 0 positive input is output of OA1/AN3(2)
10111 = Reserved
•
•
•
10000 = Reserved
01111 = Channel 0 positive input is AN15(3)
01110 = Channel 0 positive input is AN14(3)
01101 = Channel 0 positive input is AN13(3)
•
•
•
00010 = Channel 0 positive input is AN2(3)
00001 = Channel 0 positive input is AN1(3)
00000 = Channel 0 positive input is AN0(3)
CH0NA: Channel 0 Negative Input Select for Sample MUXA bit
1 = Channel 0 negative input is AN1(1)
0 = Channel 0 negative input is VREFL
Unimplemented: Read as ‘0’
AN0 through AN7 are repurposed when comparator and op amp functionality is enabled. See Figure 23-1
to determine how enabling a particular op amp or comparator affects selection choices for Channels 1, 2,
and 3.
If the Op amp/Comparator module is enabled (COE bit (CMxCON<14>) = 1) and the op amp is selected
(OPMODE bit (CMxCON<10>) = 1), the OAx input is used; otherwise, the ANx input is used.
See the “Pin Diagrams” section for the available analog channels for each device.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 329
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-6:
AD1CHS0: ADC1 INPUT CHANNEL 0 SELECT REGISTER
CH0SA<4:0>: Channel 0 Positive Input Select for Sample MUXA bits(1)
11111 = Open; use this selection with CTMU capacitive and time measurement
11110 = Channel 0 positive input is connected to CTMU temperature measurement diode
(CTMU TEMP)
11101 = Reserved
11100 = Reserved
11011 = Reserved
11010 = Channel 0 positive input is output of OA3/AN6(2)
11001 = Channel 0 positive input is output of OA2/AN0(2)
11000 = Channel 0 positive input is output of OA1/AN3(2)
10110 = Reserved
•
•
•
10000 = Reserved
01111 = Channel 0 positive input is AN15(1)
01110 = Channel 0 positive input is AN14(1)
01101 = Channel 0 positive input is AN13(1)
•
•
•
00010 = Channel 0 positive input is AN2(1)
00001 = Channel 0 positive input is AN1(1)
00000 = Channel 0 positive input is AN0(1)
bit 4-0
Note 1:
2:
3:
AN0 through AN7 are repurposed when comparator and op amp functionality is enabled. See Figure 23-1
to determine how enabling a particular op amp or comparator affects selection choices for Channels 1, 2,
and 3.
If the Op amp/Comparator module is enabled (COE bit (CMxCON<14>) = 1) and the op amp is selected
(OPMODE bit (CMxCON<10>) = 1), the OAx input is used; otherwise, the ANx input is used.
See the “Pin Diagrams” section for the available analog channels for each device.
DS70657E-page 330
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-7:
R/W-0
CSS31
bit 15
U-0
—
AD1CSSH: ADC1 INPUT SCAN SELECT REGISTER HIGH(1)
R/W-0
CSS30
U-0
—
U-0
—
U-0
—
R/W-0
CSS26(2)
R/W-0
CSS25(2)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
CSS24(2)
bit 8
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-11
bit 10
bit 9
bit 8
bit 7-0
Note 1:
2:
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
CSS31: ADC Input Scan Selection bits
1 = Select CTMU capacitive and time measurement for input scan (Open)
0 = Skip CTMU capacitive and time measurement for input scan (Open)
CSS30: ADC Input Scan Selection bits
1 = Select CTMU on-chip temperature measurement for input scan (CTMU TEMP)
0 = Skip CTMU on-chip temperature measurement for input scan (CTMU TEMP)
Unimplemented: Read as ‘0’
CSS26: ADC Input Scan Selection bits(2)
1 = Select OA3/AN6 for input scan
0 = Skip OA3/AN6 for input scan
CSS25: ADC Input Scan Selection bits(2)
1 = Select OA2/AN0 for input scan
0 = Skip OA2/AN0 for input scan
CSS24: ADC Input Scan Selection bits(2)
1 = Select OA1/AN3 for input scan
0 = Skip OA1/AN3 for input scan
Unimplemented: Read as ‘0’
All ADxCSSH bits can be selected by user software. However, inputs selected for scan without a
corresponding input on device convert VREFL.
If the Op amp/Comparator module is enabled (COE bit (CMxCON<14>) = 1) and the op amp is selected
(OPMODE bit (CMxCON<10>) = 1), the OAx input is used; otherwise, the ANx input is used.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 331
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 23-8:
AD1CSSL: ADC1 INPUT SCAN SELECT REGISTER LOW(1,2)
R/W-0
CSS15
bit 15
R/W-0
CSS14
R/W-0
CSS13
R/W-0
CSS12
R/W-0
CSS11
R/W-0
CSS10
R/W-0
CSS9
R/W-0
CSS8
bit 8
R/W-0
CSS7
bit 7
R/W-0
CSS6
R/W-0
CSS5
R/W-0
CSS4
R/W-0
CSS3
R/W-0
CSS2
R/W-0
CSS1
R/W-0
CSS0
bit 0
Legend:
R = Readable bit
-n = Value at POR
bit 15-0
Note 1:
2:
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
CSS<15:0>: ADC Input Scan Selection bits
1 = Select ANx for input scan
0 = Skip ANx for input scan
On devices with less than 16 analog inputs, all AD1CSSL bits can be selected by the user. However,
inputs selected for scan without a corresponding input on device convert VREFL.
CSSx = ANx, where x = 0-15.
DS70657E-page 332
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
24.0
PERIPHERAL TRIGGER
GENERATOR (PTG) MODULE
Note 1: This data sheet summarizes the features of the dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Section 32. Peripheral
Trigger
Generator
(PTG)”
(DS70669) of the “dsPIC33E/PIC24E
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
24.1
Module Introduction
The Peripheral Trigger Generator (PTG) provides a
means to schedule complex high-speed peripheral
operations that would be difficult to achieve using software. The PTG module uses 8-bit commands called
“steps” that the user writes to the PTG Queue register
(PTGQUE0-PTQUE7), which performs operations
such as wait for input signal, generate output trigger,
and wait for timer.
© 2011-2012 Microchip Technology Inc.
The PTG module has the following major features:
•
•
•
•
•
Multiple clock sources
Two 16-bit general purpose timers
Two 16-bit general limit counters
Configurable for rising or falling edge triggering
Generates processor interrupts to include:
- Four configurable processor interrupts
- Interrupt on a step event in Single-Step mode
- Interrupt on a PTG Watchdog Timer time-out
• Able to receive trigger signals from these
peripherals:
- ADC
- PWM
- Output Compare
- Input Capture
- Op amp/Comparator
- INT2
• Able to trigger or synchronize to these
peripherals:
- Watchdog Timer
- Output Compare
- Input Capture
- ADC
- PWM
- Op amp/Comparator
Preliminary
DS70657E-page 333
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 24-1:
PTG BLOCK DIAGRAM
PTGHOLD
PTGL0<15:0>
PTGADJ
STEP Command
PTGTxLIM<15:0>
PTG General
Purpose
Timer x
PTGCxLIM<15:0>
PTG Loop
Counter x
PTGSDLIM<15:0>
PTG Step
Delay Timer
PTGBTE<15:0>
16-bit Data Bus
PTGCST<15:0>
STEP Command
PTGCON<15:0>
Trigger Outputs
PTGDIV<4:0>
FP
TAD
T1CLK
T2CLK
T3CLK
FOSC
Clock Inputs
PTGCLK<2:0>
÷
PTG Control Logic
Trigger Inputs
PWM
OC1
OC2
IC1
CMPx
ADC
INT2
STEP Command
PTG Interrupts
STEP Command
PTGO0
•
•
•
PTGO31
PTG0IF
•
•
•
PTG3IF
AD1CHS0<15:0>
PTGQPTR<4:0>
PTG Watchdog
Timer(1)
PTGQUE0
PTGWDTIF
PTGQUE1
PTGQUE2
PTGQUE3
PTGQUE4
Command
Decoder
PTGQUE5
PTGQUE6
PTGQUE7
PTGSTEPIF
Note 1: This is a dedicated Watchdog Timer for the PTG module and is independent of the device watchdog timer.
DS70657E-page 334
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
24.2
PTG Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
24.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 32. “Peripheral Trigger Generator”
(DS70669)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 335
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
24.3
PTG Control Registers
REGISTER 24-1:
PTGCST: PTG CONTROL/STATUS REGISTER
R/W-0
U-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
R/W-0
PTGEN
—
PTGSIDL
PTGTOGL
—
PTGSWT(2)
PTGSSEN
PTGIVIS
bit 15
bit 8
R/W-0
HS-0
U-0
U-0
U-0
U-0
R/W-0
PTGSTRT
PTGWDTO
—
—
—
—
PTGITM<1:0>(1)
bit 7
bit 0
Legend:
HS = Set by Hardware
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
PTGEN: Module Enable bit
1 = PTG module is enabled
0 = PTG module is disabled
bit 14
Unimplemented: Read as ‘0’
bit 13
PTGSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12
PTGTOGL: TRIG Output Toggle Mode bit
1 = Toggle state of the PTGOx for each execution of the PTGTRIG command
0 = Each execution of PTGTRIG command will generate a single PTGOx pulse determined by value
in PTGPWD
bit 11
Unimplemented: Read as ‘0’
bit 10
PTGSWT: Software Trigger bit(2)
1 = Trigger the PTG module
0 = No action (clearing this bit will have no effect)
bit 9
PTGSSEN: Enable Single Step
1 = Enable Single Step mode
0 = Disable Single Step mode
bit 8
PTGIVIS: Counter/Timer Visibility Control bit
1 = Reads of the PTGSDLIM, PTGCxLIM or PTGTxLIM registers returns the current values of their
corresponding counter/timer registers (PTGSD, PTGCx, PTGTx)
0 = Reads of the PTGSDLIM, PTGCxLIM or PTGTxLIM registers returns the value previously written
to those limit registers
bit 7
PTGSTRT: Start PTG Sequencer bit
1 = Start to sequentially execute commands (Continuous mode)
0 = Stop executing commands
bit 6
PTGWDTO: PTG Watchdog Timer Time-out Status bit
1 = PTG watchdog timer has timed out
0 = PTG watchdog timer has not timed out.
bit 5-2
Unimplemented: Read as ‘0’
Note 1:
2:
These bit apply to the PTGWHI and PTGWLO commands only.
This bit is only used with the PTGCTRL step command software trigger option.
DS70657E-page 336
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-1:
bit 1-0
Note 1:
2:
PTGCST: PTG CONTROL/STATUS REGISTER (CONTINUED)
PTGITM<1:0>: PTG Input Trigger Command Operating Mode bits(1)
11 = Single level detect with step delay not executed on exit of command (regardless of PTGCTRL
command)
10 = Single level detect with step delay executed on exit of command
01 = Continuous edge detect with step delay not executed on exit of command (regardless of
PTGCTRL command)
00 = Continuous edge detect with step delay executed on exit of command
These bit apply to the PTGWHI and PTGWLO commands only.
This bit is only used with the PTGCTRL step command software trigger option.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 337
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-2:
R/W-0
PTGCON: PTG CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
PTGCLK<2:0>
R/W-0
R/W-0
R/W-0
PTGDIV<4:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
PTGPWD<3:0>
R/W-0
R/W-0
R/W-0
—
R/W-0
R/W-0
PTGWDT<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-13
PTGCLK<2:0>: Select PTG Module Clock Source bits
111 = Reserved
110 = Reserved
101 = PTG module clock source will be T3CLK
100 = PTG module clock source will be T2CLK
011 = PTG module clock source will be T1CLK
010 = PTG module clock source will be TAD
001 = PTG module clock source will be FOSC
000 = PTG module clock source will be FP
bit 12-8
PTGDIV<4:0>: PTG Module Clock Prescaler (divider) bits
11111 = Divide by 32
11110 = Divide by 31
•
•
•
00001 = Divide by 2
00000 = Divide by 1
bit 7-4
PTGPWD<3:0>: PTG Trigger Output Pulse Width bits
1111 = All trigger outputs are 16 PTG clock cycles wide
1110 = All trigger outputs are 15 PTG clock cycles wide
•
•
•
0001 = All trigger outputs are 2 PTG clock cycles wide
0000 = All trigger outputs are 1 PTG clock cycle wide
bit 3
Unimplemented: Read as ‘0’
bit 2-0
PTGWDT<2:0>: Select PTG Watchdog Time-out Count Value bits
111 = Watchdog will time out after 512 PTG clocks
110 = Watchdog will time out after 256 PTG clocks
101 = Watchdog will time out after 128 PTG clocks
100 = Watchdog will time out after 64 PTG clocks
011 = Watchdog will time out after 32 PTG clocks
010 = Watchdog will time out after 16 PTG clocks
001 = Watchdog will time out after 8 PTG clocks
000 = Watchdog is disabled
DS70657E-page 338
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-3:
PTGBTE: PTG BROADCAST TRIGGER ENABLE REGISTER(1,2)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCTS4
ADCTS3
ADCTS2
ADCTS1
IC4TSS
IC3TSS
IC2TSS
IC1TSS
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
OC4CS
OC3CS
OC2CS
OC1CS
OC4TSS
OC3TSS
OC2TSS
OC1TSS
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
ADCTS4: Sample Trigger PTGO15 for ADC bit
1 = Generate trigger when the broadcast command is executed
0 = Do not generate trigger when the broadcast command is executed
bit 14
ADCTS3: Sample Trigger PTGO14 for ADC bit
1 = Generate trigger when the broadcast command is executed
0 = Do not generate trigger when the broadcast command is executed
bit 13
ADCTS2: Sample Trigger PTGO13 for ADC bit
1 = Generate trigger when the broadcast command is executed
0 = Do not generate trigger when the broadcast command is executed
bit 12
ADCTS1: Sample Trigger PTGO12 for ADC bit
1 = Generate trigger when the broadcast command is executed
0 = Do not generate trigger when the broadcast command is executed
bit 11
IC4TSS: Trigger/Synchronization Source for IC4 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 10
IC3TSS: Trigger/Synchronization Source for IC3 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 9
IC2TSS: Trigger/Synchronization Source for IC2 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 8
IC1TSS: Trigger/Synchronization Source for IC1 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 7
OC4CS: Clock Source for OC4 bit
1 = Generate clock pulse when the broadcast command is executed
0 = Do not generate clock pulse when the broadcast command is executed
bit 6
OC3CS: Clock Source for OC3 bit
1 = Generate clock pulse when the broadcast command is executed
0 = Do not generate clock pulse when the broadcast command is executed
bit 5
OC2CS: Clock Source for OC2 bit
1 = Generate clock pulse when the broadcast command is executed
0 = Do not generate clock pulse when the broadcast command is executed
Note 1:
2:
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
This register only used with the PTGCTRL OPTION = 1111 step command.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 339
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-3:
PTGBTE: PTG BROADCAST TRIGGER ENABLE REGISTER(1,2) (CONTINUED)
bit 4
OC1CS: Clock Source for OC1 bit
1 = Generate clock pulse when the broadcast command is executed
0 = Do not generate clock pulse when the broadcast command is executed
bit 3
OC4TSS: Trigger/Synchronization Source for OC4 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 2
OC3TSS: Trigger/Synchronization Source for OC3 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 1
OC2TSS: Trigger/Synchronization Source for OC2 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
bit 0
OC1TSS: Trigger/Synchronization Source for OC1 bit
1 = Generate trigger/synchronization when the broadcast command is executed
0 = Do not generate trigger/synchronization when the broadcast command is executed
Note 1:
2:
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
This register only used with the PTGCTRL OPTION = 1111 step command.
DS70657E-page 340
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-4:
R/W-0
PTGT0LIM: PTG TIMER0 LIMIT REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGT0LIM<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGT0LIM<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGT0LIM<15:0>: PTG Timer0 Limit Register bits
General purpose Timer0 limit register (effective only with a PTGT0 step command).
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
REGISTER 24-5:
R/W-0
PTGT1LIM: PTG TIMER1 LIMIT REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGT1LIM<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGT1LIM<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGT1LIM<15:0>: PTG Timer1 Limit Register bits
General purpose Timer1 limit register (effective only with a PTGT1 step command).
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 341
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-6:
R/W-0
PTGSDLIM: PTG STEP DELAY LIMIT REGISTER(1,2)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGSDLIM<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGSDLIM<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
2:
x = Bit is unknown
PTGSDLIM<15:0>: PTG Step Delay Limit Register bits
Holds a PTG Step Delay value representing the number of additional PTG clocks between the start of
a step command, and the completion of the step command.
A base step delay of one PTG clock is added to any value written to the PTGSDLIM register (Step
Delay = (PTGSDLIM) + 1).
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
REGISTER 24-7:
R/W-0
PTGC0LIM: PTG COUNTER 0 LIMIT REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGC0LIM<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGC0LIM<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGC0LIM<15:0>: PTG Counter 0 Limit Register bits
May be used to specify the loop count for the PTGJMPC0 step command, or as a limit register for the
general purpose counter 0.
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
DS70657E-page 342
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-8:
R/W-0
PTGC1LIM: PTG COUNTER 1 LIMIT REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGC1LIM<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGC1LIM<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGC1LIM<15:0>: PTG Counter 1 Limit Register bits
May be used to specify the loop count for the PTGJMPC1 step command, or as a limit register for the
general purpose counter 1.
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
REGISTER 24-9:
R/W-0
PTGHOLD: PTG HOLD REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGHOLD<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGHOLD<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGHOLD<15:0>: PTG General Purpose Hold Register bits
Holds user supplied data to be copied to the PTGTxLIM, PTGCxLIM, PTGSDLIM, or PTGL0 registers
with the PTGCOPY command.
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 343
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-10: PTGADJ: PTG ADJUST REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGADJ<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGADJ<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGADJ<15:0>: PTG Adjust Register bits
This register Holds user supplied data to be added to the PTGTxLIM, PTGCxLIM, PTGSDLIM, or
PTGL0 registers with the PTGADD command.
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
REGISTER 24-11: PTGL0: PTG LITERAL 0 REGISTER(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGL0<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGL0<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
Note 1:
x = Bit is unknown
PTGL0<15:0>: PTG Literal 0 Register bits
This register holds the 16-bit value to be written to the AD1CHS0 register with the PTGCTRL step
command
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
DS70657E-page 344
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 24-12: PTGQPTR: PTG STEP QUEUE POINTER REGISTER(1)
U-0
U-0
U-0
U-0
U-0
U-0
U-0
U-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
U-0
U-0
—
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PTGQPTR<4:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-0
Unimplemented: Read as ‘0’
bit 4-0
PTGQPTR<4:0>: PTG Step Queue Pointer Register bits
This register points to the currently active step command in the step queue.
Note 1:
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
REGISTER 24-13: PTGQUEx: PTG STEP QUEUE REGISTERS (x = 0-7)(1,3)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STEP(2x +1)<7:0>(2)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
(2)
STEP(2x)<7:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-8
STEP(2x +1)<7:0>: PTG Step Queue Pointer Register bits(2)
A queue location for storage of the STEP(2x +1) command byte.
bit 7-0
STEP(2x)<7:0>: PTG Step Queue Pointer Register bits(2)
A queue location for storage of the STEP(2x) command byte.
Note 1:
2:
3:
x = Bit is unknown
This register is read only when the PTG module is executing step commands (PTGEN = 1 and
PTGSTRT = 1).
Refer to Table 24-1 for the STEP command encoding.
The step registers maintain their values on any type of reset.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 345
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
24.4
STEP Commands and Format
TABLE 24-1:
PTG STEP COMMAND FORMAT
STEP Command Byte:
STEPx<7:0>
CMD<3:0>
OPTION<3:0>
bit 7
bit 7-4
Note 1:
2:
3:
bit 4 bit 3
CMD<3:0>
Step
Command
bit 0
Command Description
0000
PTGCTRL
Execute control command as described by OPTION<3:0>
0001
PTGADD
Add contents of PTGADJ register to target register as described by
OPTION<3:0>
PTGCOPY
Copy contents of PTGHOLD register to target register as described by
OPTION<3:0>
001x
PTGSTRB
Copy the value contained in CMD<0>:OPTION<3:0> to the CH0SA<4:0> bits
(AD1CHS0<4:0>)
0100
PTGWHI
Wait for a Low to High edge input from selected PTG trigger input as described
by OPTION<3:0>
0101
PTGWLO
Wait for a High to Low edge input from selected PTG trigger input as described
by OPTION<3:0>
0110
Reserved
Reserved
0111
PTGIRQ
Generate individual interrupt request as described by OPTION3<:0>
100x
PTGTRIG
Generate individual trigger output as described by
<<CMD<0>:OPTION<3:0>>
101x
PTGJMP
Copy the value indicated in <<CMD<0>:OPTION<3:0>> to the Queue Pointer
(PTGQPTR) and jump to that step queue
110x
PTGJMPC0
PTGC0 = PTGC0LIM: Increment the Queue Pointer (PTGQPTR)
111x
PTGJMPC1
PTGC1 = PTGC1LIM: Increment the queue pointer (PTGQPTR)
PTGC0 ≠ PTGC0LIM: Increment Counter 0 (PTGC0) and copy the value
indicated in <<CMD<0>:OPTION<3:0>> to the Queue Pointer (PTGQPTR)
and jump to that step queue
PTGC1 ≠ PTGC1LIM: Increment Counter 1 (PTGC1) and copy the value
indicated in <<CMD<0>:OPTION<3:0>> to the Queue Pointer (PTGQPTR)
and jump to that step queue
All reserved commands or options will execute but have no effect (i.e., execute as a NOP instruction).
Refer to Table 24-2 for the trigger output descriptions.
This feature is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
DS70657E-page 346
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 24-1:
bit 3-0
PTG STEP COMMAND FORMAT (CONTINUED)
Step
Command
PTGCTRL(1)
PTGADD(1)
PTGCOPY(1)
Note 1:
2:
3:
OPTION<3:0>
Option Description
0000
Reserved
0001
Reserved
0010
Disable Step Delay Timer (PTGSD)
0011
Reserved
0100
Reserved
0101
Reserved
0110
Enable Step Delay Timer (PTGSD)
0111
Reserved
1000
Start and wait for the PTG Timer 0 to match Timer 0 Limit Register
1001
Start and wait for the PTG Timer 1 to match Timer 1 Limit Register
1010
Reserved
1011
Wait for software trigger bit transition from low to high before continuing
(PTGSWT = 0 to 1)
1100
Copy contents of the Counter 0 register to the AD1CHS0 register
1101
Copy contents of the Counter 1 register to the AD1CHS0 register
1110
Copy contents of the Literal 0 register to the AD1CHS0 register
1111
Generate triggers indicated in the Broadcast Trigger Enable Register
(PTGBTE)
0000
Add contents of PTGADJ register to the Counter 0 Limit register (PTGC0LIM)
0001
Add contents of PTGADJ register to the Counter 1 Limit register (PTGC1LIM)
0010
Add contents of PTGADJ register to the Timer 0 Limit register (PTGT0LIM)
0011
Add contents of PTGADJ register to the Timer 1 Limit register (PTGT1LIM)
0100
Add contents of PTGADJ register to the Step Delay Limit register (PTGSDLIM)
0101
Add contents of PTGADJ register to the Literal 0 register (PTGL0)
0110
Reserved
0111
Reserved
1000
Copy contents of PTGHOLD register to the Counter 0 Limit register
(PTGC0LIM)
1001
Copy contents of PTGHOLD register to the Counter 1 Limit register
(PTGC1LIM)
1010
Copy contents of PTGHOLD register to the Timer 0 Limit register (PTGT0LIM)
1011
Copy contents of PTGHOLD register to the Timer 1 Limit register (PTGT1LIM)
1100
Copy contents of PTGHOLD register to the Step Delay Limit register
(PTGSDLIM)
1101
Copy contents of PTGHOLD register to the Literal 0 register (PTGL0)
1110
Reserved
1111
Reserved
All reserved commands or options will execute but have no effect (i.e., execute as a NOP instruction).
Refer to Table 24-2 for the trigger output descriptions.
This feature is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 347
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 24-1:
bit 3-0
PTG STEP COMMAND FORMAT (CONTINUED)
Step
Command
PTGWHI(1)
or
PTGWLO(1)
PTGIRQ(1)
PTGTRIG(2)
Note 1:
2:
3:
OPTION<3:0>
Option Description
0000
PWM Special Event Trigger(3)
0001
PWM Master Timebase Synchronization Output(3)
0010
PWM1 Interrupt(3)
0011
PWM2 Interrupt(3)
0100
PWM3 Interrupt(3)
0101
Reserved
0110
Reserved
0111
OC1 Trigger Event
1000
OC2 Trigger Event
1001
IC1 Trigger Event
1010
CMP1 Trigger Event
1011
CMP2 Trigger Event
1100
CMP3 Trigger Event
1101
CMP4 Trigger Event
1110
ADC Conversion Done Interrupt
1111
INT2 External Interrupt
0000
Generate PTG interrupt 0
0001
Generate PTG interrupt 1
0010
Generate PTG interrupt 2
0011
Generate PTG interrupt 3
0100
Reserved
•
•
•
•
•
•
1111
Reserved
00000
PTGO0
00001
PTGO1
•
•
•
•
•
•
11110
PTGO30
11111
PTGO31
All reserved commands or options will execute but have no effect (i.e., execute as a NOP instruction).
Refer to Table 24-2 for the trigger output descriptions.
This feature is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
DS70657E-page 348
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 24-2:
PTG OUTPUT DESCRIPTIONS
PTG Output
Number
PTG Output Description
PTGO0
Trigger/Synchronization Source for OC1
PTGO1
Trigger/Synchronization Source for OC2
PTGO2
Trigger/Synchronization Source for OC3
PTGO3
Trigger/Synchronization Source for OC4
PTGO4
Clock Source for OC1
PTGO5
Clock Source for OC2
PTGO6
Clock Source for OC3
PTGO7
Clock Source for OC4
PTGO8
Trigger/Synchronization Source for IC1
PTGO9
Trigger/Synchronization Source for IC2
PTGO10
Trigger/Synchronization Source for IC3
PTGO11
Trigger/Synchronization Source for IC4
PTGO12
Sample Trigger for ADC
PTGO13
Sample Trigger for ADC
PTGO14
Sample Trigger for ADC
PTGO15
Sample Trigger for ADC
PTGO16
PWM Time Base Synchronous Source for PWM(1)
PTGO17
PWM Time Base Synchronous Source for PWM(1)
PTGO18
Mask Input Select for Op Amp/Comparator
PTGO19
Mask Input Select for Op Amp/Comparator
PTGO20
Reserved
PTGO21
Reserved
PTGO22
Reserved
PTGO23
Reserved
PTGO24
Reserved
PTGO25
Reserved
PTGO26
Reserved
PTGO27
Reserved
PTGO28
Reserved
PTGO29
Reserved
PTGO30
PTG output to PPS input selection
PTGO31
Note 1:
PTG output to PPS input selection
This feature is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 349
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 350
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
25.0
OP AMP/COMPARATOR
MODULE
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 26. “Op amp/
Comparator”
(DS70357)
of
the
“dsPIC33E/PIC24E Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 25-1:
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices contain up
to four comparators which can be configured in various
ways. Comparators CMP1, CMP2, and CMP3 also
have the option to be configured as Op amps, with the
output being brought to an external pin for gain/filtering
connections.
As shown in Figure 25-1, individual
comparator options are specified by the Comparator
module’s Special Function Register (SFR) control bits.
These options allow users to:
•
•
•
•
Select the edge for trigger and interrupt generation
Configure the comparator voltage reference
Configure output blanking and masking
Configure as a Comparator or Op amp
(CMP1, CMP2, and CMP3 only)
Note:
Not all Op amp/Comparator input/output
connections are available on all devices.
See the “Pin Diagrams” section for
available connections.
OP AMP/COMPARATOR MODULE BLOCK DIAGRAM
Op Amp/Comparator 1, 2, 3
CCH<1:0> (CMxCON<1:0>)
CxIN1-
00
CXIN2-(1)
01
VINVIN+
CxIN1+
0
CVREFIN(1)
1
(‘x’ = 1, 2, 3)
Op amp/Comparator(2)
Blanking
Function
(see Figure 25-3)
–
+
CMPx
Digital
Filter
(see Figure 25-4)
PTG Trigger
Input
OPMODE (CMxCON<10>)
RINT
–
Op ampx
+
OAxOUT/ANx
OAx/ANx(3)
(to ADC)
CREF (CMxCON<4>)
Note 1:
2:
3:
CxOUT(1)
This input/output is not available as a selection when configured as an Op amp (OPMODE (CMxCON<10>) = 1).
This module can be configured either as an Op amp or a Comparator using the OPMODE bit.
When configured as an Op amp (OPMODE = 1), the ADC samples the Op amp output; otherwise, the ADC
samples the ANx pin.
CCH<1:0> (CM4CON<1:0>)
OA1/AN3
01
OA2/AN0
10
OA3/AN6
11
C4IN1-
00
VINVIN+
C4IN1+
1
CVREFIN
0
–
CMP4
+
Comparator 4
Blanking
Function
(see Figure 25-3)
Digital
Filter
(see Figure 25-4)
C4OUT
Trigger
Output
CREF (CMxCON<4>)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 351
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
OP AMP/COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM
VREFSEL (CVRCON<10>)
CVRSS = 1
VREF+
AVDD
CVRCON<3:0>
CVRSRC
CVR3
CVR2
CVR1
CVR0
FIGURE 25-2:
8R
CVRSS = 0
1
CVREFIN
R
0
CVREN
R
R
16-to-1 MUX
R
16 Steps
R
CVREF1O
CVR1OE (CVRCON<6>)
R
R
CVRR
AVDD
8R
CVREF2O(1)
AVSS
Note 1:
AVSS
This reference is (AVDD – AVSS)/2.
FIGURE 25-3:
CVR2OE (CVRCON<14>)
USER-PROGRAMMABLE BLANKING FUNCTION BLOCK DIAGRAM
SELSRCA<3:0>
(CMxMSKSRC<3:0>)
Blanking
Signals
MUX A
Comparator Output
MAI
“AND-OR” function
MAI
MBI
Blanking
Logic
To Digital
Filter
ANDI
AND
SELSRCB<3:0>
(CMxMSKSRC<7:4)
MCI
Blanking
Signals
MUX B
MAI
MBI
MBI
OR
MASK
HLMS
(CMxMSKCON<15)
MCI
SELSRCC<3:0>
(CMxMSKSRC<11:8)
Blanking
Signals
MUX C
CMxMSKCON
DS70657E-page 352
MCI
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 25-4:
DIGITAL FILTER INTERCONNECT BLOCK DIAGRAM
TxCLK(1,2)
1xx
SYNCO1(3)
010
FP(4)
000
FOSC(4)
001
÷
CFDIV
CFSEL<2:0> (CMxFLTR<6:4>)
From Blanking Logic
Digital Filter
CFLTREN (CMxFLTR<3>)
1
CXOUT
0
Note 1:
See the Type C Timer Block Diagram (Figure 13-2).
2:
See the Type B Timer Block Diagram (Figure 13-1).
3:
See the PWM Module Register Interconnect Diagram (Figure 16-2).
4:
See the Oscillator System Diagram (Figure 9-1).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 353
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
25.1
Op amp Application
Considerations
25.1.1
There are two configurations to take into consideration
when designing with the Op amp modules that are
available
in
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X devices. Configuration A (see Figure 25-5)
takes advantage of the internal connection to the ADC
module to route the output of the Op amp directly to the
ADC for measurement. Configuration B (see
Figure 25-6) requires that the designer externally route
the output of the Op amp (OAxOUT) to a separate analog input pin (ANx) on the device. Table 30-54 in
Section 30.0 “Electrical Characteristics” describes
the performance characteristics for the Op amps, distinguishing between the two configuration types where
applicable.
FIGURE 25-5:
OP AMP CONFIGURATION A
Figure 25-5 shows a typical inverting amplifier circuit
taking advantage of the internal connections from the
Op amp output to the input of the ADC. The advantage
of this configuration is that the user does not need to
consume another analog input (ANx) on the device,
and allows the user to simultaneous sample all three
Op amps with the ADC module, if needed. However,
the presence of the internal resistance, RINT1, adds an
error in the feedback path. Since RINT1 is an internal
resistance, in relation to the Op amp output (VOAxOUT)
and ADC internal connection (VADC), RINT1 must be
included in the numerator term of the transfer function.
See Table 30-52 in Section 30.0 “Electrical Characteristics” for the typical value of RINT1. Table 30-59
and Table 30-60 in Section 30.0 “Electrical Characteristics” describe the minimum sample time (TSAMP)
requirements for the ADC module in this configuration.
Figure 25-5 also defines the equations that should be
used when calculating the expected voltages at points
VADC and VOAXOUT.
OP AMP CONFIGURATION A
RFEEDBACK(2)
R1
VIN
CxIN1-
–
RINT1(1)
Op ampx
Bias
Voltage(4)
CxIN1+
+
OAxOUT
(VOAXOUT)
VADC
ADC(3)
OAx
(to ADC)
R FEEDBACK + R INT1
V ADC = ⎛ ---------------------------------------------------⎞ ( Bias Voltage – VIN )
⎝
⎠
R1
R FEEDBACK
V OAxOUT = ⎛ ------------------------------⎞ ( Bias Voltage – V IN )
⎝
⎠
R1
Note 1: See Table 30-52 for the Typical value.
2: See Table 30-52 for the Minimum value for the feedback resistor.
3: See Table 30-59 and Table 30-60 for the minimum sample time (TSAMP).
4: CVREF1O or CVREF2O are two options that are available for supplying bias voltage to the op amps.
DS70657E-page 354
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
25.1.2
OP AMP CONFIGURATION B
Figure 25-6 shows a typical inverting amplifier circuit
with the output of the Op amp (OAxOUT) externally
routed to a separate analog input pin (ANx) on the
device. This Op amp configuration is slightly different in
terms of the Op amp output and the ADC input
connection, therefore RINT1 is not included in the
transfer function. However, this configuration requires
the designer to externally route the Op amp output
(OAxOUT) to another analog input pin (ANx). See
Table 30-52 in Section 30.0 “Electrical Characteristics” for the typical value of RINT1. Table 30-59 and
Table 30-60 in Section 30.0 “Electrical Characteristics” describe the minimum sample time (TSAMP)
requirements for the ADC module in this configuration.
Figure 25-6 also defines the equation to be used to
calculate the expected voltage at point VOAXOUT. This
is the typical inverting amplifier equation.
FIGURE 25-6:
OP AMP CONFIGURATION B
RFEEDBACK(2)
R1
CxIN1-
VIN
–
RINT1(1)
Op ampx
CxIN1+
Bias
Voltage(4)
+
OAxOUT
(VOAXOUT)
ANx
ADC(3)
R FEEDBACK
V OAxOUT = ⎛ ------------------------------⎞ ( Bias Voltage – V IN )
⎝
⎠
R1
Note 1: See Table 30-52 for the Typical value.
2: See Table 30-52 for the Minimum value for the feedback resistor.
3: See Table 30-59 and Table 30-60 for the minimum sample time (TSAMP).
4: CVREF1O or CVREF2O are two options that are available for supplying bias voltage to the op amps.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 355
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
25.2
Op amp/Comparator Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
25.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
•
•
•
•
•
•
Section 26. “Op amp/Comparator” (DS70357)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
DS70657E-page 356
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
25.3
Op amp/Comparator Registers
REGISTER 25-1:
R/W-0
CMSIDL
bit 15
CMSTAT: OP AMP/COMPARATOR STATUS REGISTER
U-0
—
U-0
—
U-0
—
R-0
C4EVT(1)
R-0
C3EVT(1)
R-0
C2EVT(1)
U-0
U-0
U-0
U-0
R-0
R-0
R-0
—
—
—
—
C4OUT(2)
C3OUT(2)
C2OUT(2)
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-12
bit 11
bit 10
W = Writable bit
‘1’ = Bit is set
R-0
C1EVT(1)
bit 8
R-0
C1OUT(2)
bit 0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
CMSIDL: Stop in Idle Mode bit
1 = Discontinue operation of all comparators when device enters Idle mode
0 = Continue operation of all comparators in Idle mode
Unimplemented: Read as ‘0’
C4EVT: Op amp/Comparator 4 Event Status bit(1)
1 = Op amp/Comparator event occurred
0 = Op amp/Comparator event did not occur
C3EVT: Comparator 3 Event Status bit(1)
1 = Comparator event occurred
0 = Comparator event did not occur
C2EVT: Comparator 2 Event Status bit(1)
1 = Comparator event occurred
0 = Comparator event did not occur
C1EVT: Comparator 1 Event Status bit(1)
1 = Comparator event occurred
0 = Comparator event did not occur
Unimplemented: Read as ‘0’
C4OUT: Comparator 4 Output Status bit(2)
When CPOL = 0:
1 = VIN+ > VIN0 = VIN+ < VIN-
bit 9
bit 8
bit 7-4
bit 3
When CPOL = 1:
1 = VIN+ < VIN0 = VIN+ > VINNote 1:
2:
Reflects the value of the of the CEVT bit in the respective Op amp/Comparator control register,
CMxCON<9>.
Reflects the value of the COUT bit in the respective Op amp/Comparator control register, CMxCON<8>.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 357
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-1:
CMSTAT: OP AMP/COMPARATOR STATUS REGISTER (CONTINUED)
C3OUT: Comparator 3 Output Status bit(2)
When CPOL = 0:
1 = VIN+ > VIN0 = VIN+ < VIN-
bit 2
bit 1
When CPOL = 1:
1 = VIN+ < VIN0 = VIN+ > VINC2OUT: Comparator 2 Output Status bit(2)
When CPOL = 0:
1 = VIN+ > VIN0 = VIN+ < VIN-
bit 0
When CPOL = 1:
1 = VIN+ < VIN0 = VIN+ > VINC1OUT: Comparator 1 Output Status bit(2)
When CPOL = 0:
1 = VIN+ > VIN0 = VIN+ < VINWhen CPOL = 1:
1 = VIN+ < VIN0 = VIN+ > VIN-
Note 1:
2:
Reflects the value of the of the CEVT bit in the respective Op amp/Comparator control register,
CMxCON<9>.
Reflects the value of the COUT bit in the respective Op amp/Comparator control register, CMxCON<8>.
DS70657E-page 358
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-2:
CMxCON: COMPARATOR CONTROL REGISTER (x = 1, 2, OR 3)
R/W-0
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
CON
COE
CPOL
—
—
OPMODE
CEVT
COUT
bit 15
bit 8
R/W-0
R/W-0
EVPOL<1:0>
U-0
R/W-0
U-0
U-0
—
CREF
—
—
R/W-0
R/W-0
CCH<1:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CON: Op amp/Comparator Enable bit
1 = Op amp/Comparator is enabled
0 = Op amp/Comparator is disabled
bit 14
COE: Comparator Output Enable bit
1 = Comparator output is present on the CxOUT pin
0 = Comparator output is internal only
bit 13
CPOL: Comparator Output Polarity Select bit
1 = Comparator output is inverted
0 = Comparator output is not inverted
bit 12-11
Unimplemented: Read as ‘0’
bit 10
OPMODE: Op Amp/Comparator Operation Mode Select bit
1 = Circuit operates as an Op amp
0 = Circuit operates as a Comparator
bit 9
CEVT: Comparator Event bit
1 = Comparator event according to EVPOL<1:0> settings occurred; disables future triggers and
interrupts until the bit is cleared
0 = Comparator event did not occur
bit 8
COUT: Comparator Output bit
When CPOL = 0 (non-inverted polarity):
1 = VIN+ > VIN0 = VIN+ < VINWhen CPOL = 1 (inverted polarity):
1 = VIN+ < VIN0 = VIN+ > VIN-
Note 1:
2:
Inputs that are selected and not available will be tied to VSS. See the “Pin Diagrams” section for available
inputs for each package.
This input is not available when OPMODE (CMxCON<10>) = 1.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 359
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-2:
CMxCON: COMPARATOR CONTROL REGISTER (x = 1, 2, OR 3) (CONTINUED)
bit 7-6
EVPOL<1:0>: Trigger/Event/Interrupt Polarity Select bits
11 = Trigger/Event/Interrupt generated on any change of the comparator output (while CEVT = 0)
10 = Trigger/Event/Interrupt generated only on high to low transition of the polarity-selected
comparator output (while CEVT = 0)
If CPOL = 1 (inverted polarity):
Low-to-high transition of the comparator output
If CPOL = 0 (non-inverted polarity):
High-to-low transition of the comparator output
01 = Trigger/Event/Interrupt generated only on low to high transition of the polarity-selected
comparator output (while CEVT = 0)
If CPOL = 1 (inverted polarity):
High-to-low transition of the comparator output
If CPOL = 0 (non-inverted polarity):
Low-to-high transition of the comparator output
00 = Trigger/Event/Interrupt generation is disabled
bit 5
Unimplemented: Read as ‘0’
bit 4
CREF: Comparator Reference Select bit (VIN+ input)(1)
1 = VIN+ input connects to internal CVREFIN voltage(2)
0 = VIN+ input connects to CxIN1+ pin
bit 3-2
Unimplemented: Read as ‘0’
bit 1-0
CCH<1:0>: Op amp/Comparator Channel Select bits(1)
11 = Unimplemented
10 = Unimplemented
01 = Inverting input of Comparator connects to CxIN2- pin(2)
00 = Inverting input of Op amp/Comparator connects to CxIN1- pin
Note 1:
2:
Inputs that are selected and not available will be tied to VSS. See the “Pin Diagrams” section for available
inputs for each package.
This input is not available when OPMODE (CMxCON<10>) = 1.
DS70657E-page 360
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-3:
CM4CON: COMPARATOR CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
R/W-0
R/W-0
CON
COE
CPOL
—
—
—
CEVT
COUT
bit 15
bit 8
R/W-0
R/W-0
EVPOL<1:0>
U-0
R/W-0
U-0
U-0
—
CREF
—
—
R/W-0
R/W-0
CCH<1:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CON: Comparator Enable bit
1 = Comparator is enabled
0 = Comparator is disabled
bit 14
COE: Comparator Output Enable bit
1 = Comparator output is present on the CxOUT pin
0 = Comparator output is internal only
bit 13
CPOL: Comparator Output Polarity Select bit
1 = Comparator output is inverted
0 = Comparator output is not inverted
bit 12-10
Unimplemented: Read as ‘0’
bit 9
CEVT: Comparator Event bit
1 = Comparator event according to EVPOL<1:0> settings occurred; disables future triggers and
interrupts until the bit is cleared
0 = Comparator event did not occur
bit 8
COUT: Comparator Output bit
When CPOL = 0 (non-inverted polarity):
1 = VIN+ > VIN0 = VIN+ < VINWhen CPOL = 1 (inverted polarity):
1 = VIN+ < VIN0 = VIN+ > VIN-
bit 7-6
EVPOL<1:0>: Trigger/Event/Interrupt Polarity Select bits
11 = Trigger/Event/Interrupt generated on any change of the comparator output (while CEVT = 0)
10 = Trigger/Event/Interrupt generated only on high to low transition of the polarity-selected
comparator output (while CEVT = 0)
If CPOL = 1 (inverted polarity):
Low-to-high transition of the comparator output
If CPOL = 0 (non-inverted polarity):
High-to-low transition of the comparator output
01 = Trigger/Event/Interrupt generated only on low to high transition of the polarity-selected
comparator output (while CEVT = 0)
If CPOL = 1 (inverted polarity):
High-to-low transition of the comparator output
If CPOL = 0 (non-inverted polarity):
Low-to-high transition of the comparator output
00 = Trigger/Event/Interrupt generation is disabled
Note 1:
Inputs that are selected and not available will be tied to VSS. See the “Pin Diagrams” section for available
inputs for each package.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 361
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-3:
CM4CON: COMPARATOR CONTROL REGISTER (CONTINUED)
bit 5
Unimplemented: Read as ‘0’
bit 4
CREF: Comparator Reference Select bit (VIN+ input)(1)
1 = VIN+ input connects to internal CVREFIN voltage
0 = VIN+ input connects to C4IN1+ pin
bit 3-2
Unimplemented: Read as ‘0’
bit 1-0
CCH<1:0>: Comparator Channel Select bits(1)
11 = VIN- input of comparator connects to OA3/AN6
10 = VIN- input of comparator connects to OA2/AN0
01 = VIN- input of comparator connects to OA1/AN3
00 = VIN- input of comparator connects to C4IN1-
Note 1:
Inputs that are selected and not available will be tied to VSS. See the “Pin Diagrams” section for available
inputs for each package.
DS70657E-page 362
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-4:
CMxMSKSRC: COMPARATOR MASK SOURCE SELECT CONTROL REGISTER
U-0
U-0
U-0
U-0
—
—
—
—
R/W-0
R/W-0
R/W-0
RW-0
SELSRCC<3:0>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SELSRCB<3:0>
R/W-0
R/W-0
R/W-0
SELSRCA<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-12
Unimplemented: Read as ‘0’
bit 11-8
SELSRCC<3:0>: Mask C Input Select bits
1111 = FLT4
1110 = FLT2
1101 = PTGO19
1100 = PTGO18
1011 = Reserved
1010 = Reserved
1001 = Reserved
1000 = Reserved
0111 = Reserved
0110 = Reserved
0101 = PWM3H
0100 = PWM3L
0011 = PWM2H
0010 = PWM2L
0001 = PWM1H
0000 = PWM1L
bit 7-4
SELSRCB<3:0>: Mask B Input Select bits
1111 = FLT4
1110 = FLT2
1101 = PTGO19
1100 = PTGO18
1011 = Reserved
1010 = Reserved
1001 = Reserved
1000 = Reserved
0111 = Reserved
0110 = Reserved
0101 = PWM3H
0100 = PWM3L
0011 = PWM2H
0010 = PWM2L
0001 = PWM1H
0000 = PWM1L
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 363
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-4:
bit 3-0
CMxMSKSRC: COMPARATOR MASK SOURCE SELECT CONTROL REGISTER
SELSRCA<3:0>: Mask A Input Select bits
1111 = FLT4
1110 = FLT2
1101 = PTGO19
1100 = PTGO18
1011 = Reserved
1010 = Reserved
1001 = Reserved
1000 = Reserved
0111 = Reserved
0110 = Reserved
0101 = PWM3H
0100 = PWM3L
0011 = PWM2H
0010 = PWM2L
0001 = PWM1H
0000 = PWM1L
DS70657E-page 364
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-5:
CMxMSKCON: COMPARATOR MASK GATING CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
HLMS
—
OCEN
OCNEN
OBEN
OBNEN
OAEN
OANEN
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
NAGS
PAGS
ACEN
ACNEN
ABEN
ABNEN
AAEN
AANEN
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
HLMS: High or Low-Level Masking Select bits
1 = The masking (blanking) function will prevent any asserted (‘0’) comparator signal from propagating
0 = The masking (blanking) function will prevent any asserted (‘1’) comparator signal from propagating
bit 14
Unimplemented: Read as ‘0’
bit 13
OCEN: OR Gate C Input Enable bit
1 = MCI is connected to OR gate
0 = MCI is not connected to OR gate
bit 12
OCNEN: OR Gate C Input Inverted Enable bit
1 = Inverted MCI is connected to OR gate
0 = Inverted MCI is not connected to OR gate
bit 11
OBEN: OR Gate B Input Enable bit
1 = MBI is connected to OR gate
0 = MBI is not connected to OR gate
bit 10
OBNEN: OR Gate B Input Inverted Enable bit
1 = Inverted MBI is connected to OR gate
0 = Inverted MBI is not connected to OR gate
bit 9
OAEN: OR Gate A Input Enable bit
1 = MAI is connected to OR gate
0 = MAI is not connected to OR gate
bit 8
OANEN: OR Gate A Input Inverted Enable bit
1 = Inverted MAI is connected to OR gate
0 = Inverted MAI is not connected to OR gate
bit 7
NAGS: AND Gate Output Inverted Enable bit
1 = Inverted ANDI is connected to OR gate
0 = Inverted ANDI is not connected to OR gate
bit 6
PAGS: AND Gate Output Enable bit
1 = ANDI is connected to OR gate
0 = ANDI is not connected to OR gate
bit 5
ACEN: AND Gate C Input Enable bit
1 = MCI is connected to AND gate
0 = MCI is not connected to AND gate
bit 4
ACNEN: AND Gate C Input Inverted Enable bit
1 = Inverted MCI is connected to AND gate
0 = Inverted MCI is not connected to AND gate
bit 3
ABEN: AND Gate B Input Enable bit
1 = MBI is connected to AND gate
0 = MBI is not connected to AND gate
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 365
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-5:
CMxMSKCON: COMPARATOR MASK GATING CONTROL REGISTER
bit 2
ABNEN: AND Gate B Input Inverted Enable bit
1 = Inverted MBI is connected to AND gate
0 = Inverted MBI is not connected to AND gate
bit 1
AAEN: AND Gate A Input Enable bit
1 = MAI is connected to AND gate
0 = MAI is not connected to AND gate
bit 0
AANEN: AND Gate A Input Inverted Enable bit
1 = Inverted MAI is connected to AND gate
0 = Inverted MAI is not connected to AND gate
DS70657E-page 366
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-6:
CMxFLTR: COMPARATOR FILTER CONTROL REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
I-0
—
—
—
—
—
—
—
—
bit 15
bit 8
U-0
R/W-0
—
R/W-0
R/W-0
CFSEL<2:0>
R/W-0
R/W-0
CFLTREN
R/W-0
R/W-0
CFDIV<2:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-7
Unimplemented: Read as ‘0’
bit 6-4
CFSEL<2:0>: Comparator Filter Input Clock Select bits
111 = T5CLK(1)
110 = T4CLK(2)
101 = T3CLK(1)
100 = T2CLK(2)
011 = Reserved
010 = SYNCO1(3)
001 = FOSC(4)
000 = FP(4)
bit 3
CFLTREN: Comparator Filter Enable bit
1 = Digital filter enabled
0 = Digital filter disabled
bit 2-0
CFDIV<2:0>: Comparator Filter Clock Divide Select bits
111 = Clock Divide 1:128
110 = Clock Divide 1:64
101 = Clock Divide 1:32
100 = Clock Divide 1:16
011 = Clock Divide 1:8
010 = Clock Divide 1:4
001 = Clock Divide 1:2
000 = Clock Divide 1:1
Note 1:
2:
3:
4:
x = Bit is unknown
See the Type C Timer Block Diagram (Figure 13-2).
See the Type B Timer Block Diagram (Figure 13-1).
See the PWM Module Register Interconnect Diagram (Figure 16-2).
See the Oscillator System Diagram (Figure 9-1).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 367
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 25-7:
CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER
U-0
R/W-0
U-0
U-0
U-0
R/W-0
U-0
U-0
—
CVR2OE(1)
—
—
—
VREFSEL
—
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
CVREN
CVR1OE(1)
CVRR
CVRSS
R/W-0
R/W-0
R/W-0
R/W-0
CVR<3:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14
CVR2OE: Comparator Voltage Reference 2 Output Enable bit(1)
1 = (AVDD – AVSS)/2 is connected to the CVREF2O pin
0 = (AVDD – AVSS)/2 is disconnected from the CVREF2O pin
bit 13-11
Unimplemented: Read as ‘0’
bit 10
VREFSEL: Voltage Reference Select bit
1 = CVREFIN = VREF+
0 = CVREFIN is generated by the resistor network
bit 9-8
Unimplemented: Read as ‘0’
bit 7
CVREN: Comparator Voltage Reference Enable bit
1 = Comparator voltage reference circuit powered on
0 = Comparator voltage reference circuit powered down
bit 6
CVR1OE: Comparator Voltage Reference 1 Output Enable bit(1)
1 = Voltage level is output on CVREF1O pin
0 = Voltage level is disconnected from CVREF1O pin
bit 5
CVRR: Comparator Voltage Reference Range Selection bit
1 = CVRSRC/24 step size
0 = CVRSRC/32 step size
bit 4
CVRSS: Comparator Voltage Reference Source Selection bit
1 = Comparator voltage reference source, CVRSRC = (VREF+) – (AVSS)
0 = Comparator voltage reference source, CVRSRC = AVDD – AVSS
bit 3-0
CVR<3:0> Comparator Voltage Reference Value Selection 0 ≤ CVR<3:0> ≤15 bits
When CVRR = 1:
CVREFIN = (CVR<3:0>/24) • (CVRSRC)
When CVRR = 0:
CVREFIN = (CVRSRC/4) + (CVR<3:0>/32) • (CVRSRC)
Note 1:
CVRxOE overrides the TRISx and the ANSELx bit settings.
DS70657E-page 368
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
26.0
PROGRAMMABLE CYCLIC
REDUNDANCY CHECK (CRC)
GENERATOR
The programmable CRC generator offers the following
features:
• User-programmable (up to 32nd order)
polynomial CRC equation
• Interrupt output
• Data FIFO
Note 1: This data sheet summarizes the features
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 27. “Programmable Cyclic Redundancy Check
(CRC)” (DS70346) of the “dsPIC33E/
PIC24E Family Reference Manual”,
which is available from the Microchip web
site (www.microchip.com).
The programmable CRC generator provides a
hardware-implemented method of quickly generating
checksums for various networking and security
applications. It offers the following features:
• User-programmable CRC polynomial equation,
up to 32 bits
• Programmable shift direction (little or big-endian)
• Independent data and polynomial lengths
• Configurable Interrupt output
• Data FIFO
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
FIGURE 26-1:
A simplified block diagram of the CRC generator is
shown in Figure 26-1. A simple version of the CRC shift
engine is shown in Figure 26-2.
CRC BLOCK DIAGRAM
CRCDATH
CRCDATL
Variable FIFO
(4x32, 8x16 or 16x8)
FIFO Empty Event
CRCISEL
2 * FP Shift Clock
Shift Buffer
0
1
1
LENDIAN
Shift Complete Event
CRC Shift Engine
CRCWDATH
FIGURE 26-2:
Set CRCIF
0
CRCWDATL
CRC SHIFT ENGINE DETAIL
CRCWDATH
CRCWDATL
Read/Write Bus
X(1)(1)
Shift Buffer
Data
Note 1:
2:
Bit 0
X(n)(1)
X(2)(1)
Bit 1
Bit 2
Bit n(2)
Each XOR stage of the shift engine is programmable. See text for details.
Polynomial length n is determined by ([PLEN<4:0>] + 1).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 369
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
26.1
Overview
26.2
The CRC module can be programmed for CRC
polynomials of up to the 32nd order, using up to 32 bits.
Polynomial length, which reflects the highest exponent
in the equation, is selected by the PLEN<4:0> bits
(CRCCON2<4:0>).
The CRCXORL and CRCXORH registers control which
exponent terms are included in the equation. Setting a
particular bit includes that exponent term in the
equation; functionally, this includes an XOR operation
on the corresponding bit in the CRC engine. Clearing
the bit disables the XOR.
For example, consider two CRC polynomials, one a 16bit equation and the other a 32-bit equation:
x16 + x12 + x5 + 1
and
x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10 + x8 + x7
+ x5 + x4 + x2 + x + 1
To program these polynomials into the CRC generator,
set the register bits as shown in Table 26-1.
Note that the appropriate positions are set to ‘1’ to
indicate that they are used in the equation (for example,
X26 and X23). The 0 bit required by the equation is
always XORed; thus, X0 is a don’t care. For a polynomial of length N, it is assumed that the Nth bit will
always be used, regardless of the bit setting. Therefore,
for a polynomial length of 32, there is no 32nd bit in the
CRCxOR register.
TABLE 26-1:
Programmable CRC Resources
Many useful resources are provided on the main product page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
Note:
26.2.1
In the event you are not able to access the
product page using the link above, enter
this URL in your browser:
http://www.microchip.com/wwwproducts/
Devices.aspx?dDocName=en555464
KEY RESOURCES
• Section 27. “Programmable Cyclic Redundancy
Check (CRC)” (DS70346)
• Code Samples
• Application Notes
• Software Libraries
• Webinars
• All related dsPIC33E/PIC24E Family Reference
Manuals Sections
• Development Tools
CRC SETUP EXAMPLES FOR
16 AND 32-BIT POLYNOMIAL
CRC Control
Bits
PLEN<4:0>
Bit Values
16-bit
Polynomial
32-bit
Polynomial
01111
11111
X<31:16>
0000 0000
0000 000x
0000 0100
1100 0001
X<15:0>
0001 0000
0010 000x
0001 1101
1011 011x
DS70657E-page 370
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
26.3
Programmable CRC Registers
REGISTER 26-1:
CRCCON1: CRC CONTROL REGISTER 1
R/W-0
U-0
R/W-0
CRCEN
—
CSIDL
R-0
R-0
R-0
R-0
R-0
VWORD<4:0>
bit 15
bit 8
R-0
R-1
R/W-0
R/W-0
R/W-0
U-0
U-0
U-0
CRCFUL
CRCMPT
CRCISEL
CRCGO
LENDIAN
—
—
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
CRCEN: CRC Enable bit
1 = CRC module is enabled
0 = CRC module is disabled. All state machines, pointers, and CRCWDAT/CRCDAT are reset. Other
SFRs are not reset.
bit 14
Unimplemented: Read as ‘0’
bit 13
CSIDL: CRC Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
bit 12-8
VWORD<4:0>: Pointer Value bits
Indicates the number of valid words in the FIFO. Has a maximum value of 8 when PLEN<4:0> > 7,
or 16 when PLEN<4:0> ≤7.
bit 7
CRCFUL: FIFO Full bit
1 = FIFO is full
0 = FIFO is not full
bit 6
CRCMPT: FIFO Empty Bit
1 = FIFO is empty
0 = FIFO is not empty
bit 5
CRCISEL: CRC Interrupt Selection bit
1 = Interrupt on FIFO empty; final word of data is still shifting through CRC
0 = Interrupt on shift complete and CRCWDAT results ready
bit 4
CRCGO: Start CRC bit
1 = Start CRC serial shifter
0 = CRC serial shifter is turned off
bit 3
LENDIAN: Data Word Little-Endian Configuration bit
1 = Data word is shifted into the CRC starting with the LSb (little endian)
0 = Data word is shifted into the CRC starting with the MSb (big endian)
bit 2-0
Unimplemented: Read as ‘0’
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 371
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 26-2:
CRCCON2: CRC CONTROL REGISTER 2
U-0
U-0
U-0
—
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DWIDTH<4:0>
bit 15
bit 8
U-0
U-0
U-0
—
—
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PLEN<4:0>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-13
Unimplemented: Read as ‘0’
bit 12-8
DWIDTH<4:0>: Data Width Select bits
These bits set the width of the data word (DWIDTH<4:0> + 1)
bit 7-5
Unimplemented: Read as ‘0’
bit 4-0
PLEN<4:0>: Polynomial Length Select bits
These bits set the length of the polynomial (Polynomial Length = PLEN<4:0> + 1)
DS70657E-page 372
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 26-3:
R/W-0
CRCXORH: CRC XOR POLYNOMIAL HIGH REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
X<31:24>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
X<23:16>
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-0
x = Bit is unknown
X<31:16>: XOR of Polynomial Term Xn Enable bits
REGISTER 26-4:
R/W-0
CRCXORL: CRC XOR POLYNOMIAL LOW REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
X<15:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
X<7:1>
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 15-1
X<15:1>: XOR of Polynomial Term Xn Enable bits
bit 0
Unimplemented: Read as ‘0’
© 2011-2012 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS70657E-page 373
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 374
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
27.0
Note:
SPECIAL FEATURES
27.1
This data sheet summarizes the features of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X
families
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to the related section of the
“dsPIC33E/PIC24E
Family
Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices include several
features intended to maximize application flexibility and
reliability, and minimize cost through elimination of
external components. These are:
•
•
•
•
•
•
Flexible configuration
Watchdog Timer (WDT)
Code Protection and CodeGuard™ Security
JTAG Boundary Scan Interface
In-Circuit Serial Programming™ (ICSP™)
In-Circuit Emulation
Configuration Bits
In dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices, the
configuration bytes are implemented as volatile memory.
This means that configuration data must be
programmed each time the device is powered up.
Configuration data is stored in at the top of the on-chip
program memory space, known as the Flash Configuration Bytes. Their specific locations are shown in
Table 27-1. The configuration data is automatically
loaded from the Flash Configuration Bytes to the proper
Configuration shadow registers during device Resets.
Note:
Configuration data is reloaded on all types
of device Resets.
When creating applications for these devices, users
should always specifically allocate the location of the
Flash Configuration Bytes for configuration data in their
code for the compiler. This is to make certain that program code is not stored in this address when the code
is compiled.
The upper 2 bytes of all Flash Configuration Words in
program memory should always be ‘1111 1111 1111
1111’. This makes them appear to be NOP instructions
in the remote event that their locations are ever
executed by accident. Since Configuration bits are not
implemented in the corresponding locations, writing
‘1’s to these locations has no effect on device
operation.
Note:
Performing a page erase operation on the
last page of program memory clears the
Flash Configuration Bytes, enabling code
protection as a result. Therefore, users
should avoid performing page erase
operations on the last page of program
memory.
The Configuration Flash Bytes map is shown in
Table 27-1.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 375
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 27-1:
File Name Address
Reserved
Reserved
FICD
FPOR
FWDT
FOSC
CONFIGURATION BYTE REGISTER MAP
Device
Memory
Size
(KB)
0057EC
32
00AFEC
64
0157EC
128
02AFEC
256
0557EC
512
0057EE
32
00AFEE
64
0157EE
128
02AFEE
256
0557EE
512
0057F0
32
00AFF0
64
0157F0
128
02AFF0
256
0557F0
512
0057F2
32
00AFF2
64
0157F2
128
02AFF2
256
0057F2
512
0057F4
32
00AFF4
64
0157F4
128
02AFF4
256
0057F4
512
0057F6
32
00AFF6
64
0157F6
128
02AFF6
256
0057F6
512
FOSCSEL 0057F8
32
FGS
Reserved
Reserved
Legend:
Note 1:
2:
3:
00AFF8
64
0157F8
128
02AFF8
256
0057F8
512
0057FA
32
00AFFA
64
0157FA
128
02AFFA
256
0057FA
512
0057FC
32
00AFFC
64
0157FC
128
02AFFC
256
0057FC
512
057FFE
32
00AFFE
64
0157FE
128
02AFFE
256
0057FE
512
Bit 23-8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Reserved(3)
—
JTAGEN
WDTWIN<1:0>
ALTI2C2
ALTI2C1
PLLKEN
WDTPRE
IOL1WAY
—
—
—
—
—
FWDTEN
WINDIS
FCKSM<1:0>
Reserved(2) Reserved(3)
—
Reserved(3)
—
ICS<1:0>
—
—
WDTPOST<3:0>
OSCIOFNC
POSCMD<1:0>
—
IESO
PWMLOCK(1)
—
—
—
—
—
—
—
—
—
—
GCP
GWRP
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
FNOSC<2:0>
— = unimplemented, read as ‘1’.
These bits are only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
This bit is reserved and must be programmed as ‘0’.
This bit is reserved and must be programmed as ‘1’.
DS70657E-page 376
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 27-2:
CONFIGURATION BITS DESCRIPTION
Bit Field
Description
GCP
General Segment Code-Protect bit
1 = User program memory is not code-protected
0 = Code protection is enabled for the entire program memory space
GWRP
General Segment Write-Protect bit
1 = User program memory is not write-protected
0 = User program memory is write-protected
IESO
Two-speed Oscillator Start-up Enable bit
1 = Start-up device with FRC, then automatically switch to the
user-selected oscillator source when ready
0 = Start-up device with user-selected oscillator source
PWM Lock Enable bit
PWMLOCK(1)
1 = Certain PWM registers may only be written after key sequence
0 = PWM registers may be written without key
FNOSC<2:0>
Oscillator Selection bits
111 = Fast RC Oscillator with divide-by-N (FRCDIVN)
110 = Reserved; do not use
101 = Low-Power RC Oscillator (LPRC)
100 = Reserved; do not use
011 = Primary Oscillator with PLL module (XT + PLL, HS + PLL, EC + PLL)
010 = Primary Oscillator (XT, HS, EC)
001 = Fast RC Oscillator with divide-by-N with PLL module (FRCPLL)
000 = Fast RC Oscillator (FRC)
FCKSM<1:0>
Clock Switching Mode bits
1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled
01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled
00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled
IOL1WAY
Peripheral pin select configuration
1 = Allow only one reconfiguration
0 = Allow multiple reconfigurations
OSCIOFNC
OSC2 Pin Function bit (except in XT and HS modes)
1 = OSC2 is clock output
0 = OSC2 is general purpose digital I/O pin
POSCMD<1:0>
Primary Oscillator Mode Select bits
11 = Primary oscillator disabled
10 = HS Crystal Oscillator mode
01 = XT Crystal Oscillator mode
00 = EC (External Clock) mode
FWDTEN
Watchdog Timer Enable bit
1 = Watchdog Timer always enabled (LPRC oscillator cannot be disabled. Clearing the
SWDTEN bit in the RCON register will have no effect.)
0 = Watchdog Timer enabled/disabled by user software (LPRC can be disabled by clearing
the SWDTEN bit in the RCON register)
WINDIS
Watchdog Timer Window Enable bit
1 = Watchdog Timer in Non-Window mode
0 = Watchdog Timer in Window mode
PLLKEN
PLL Lock Enable bit
1 = PLL lock enabled
0 = PLL lock disabled
WDTPRE
Watchdog Timer Prescaler bit
1 = 1:128
0 = 1:32
Note 1: This bit is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 377
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 27-2:
CONFIGURATION BITS DESCRIPTION (CONTINUED)
Bit Field
WDTPOST<3:0>
Description
Watchdog Timer Postscaler bits
1111 = 1:32,768
1110 = 1:16,384
•
•
•
WDTWIN<1:0>
ALTI2C1
0001 = 1:2
0000 = 1:1
Watchdog Window Select bits
11 = WDT Window is 25% of WDT period
10 = WDT Window is 37.5% of WDT period
01 = WDT Window is 50% of WDT period
00 = WDT Window is 75% of WDT period
Alternate I2C1 pins
1 = I2C1 mapped to SDA1/SCL1 pins
0 = I2C1 mapped to ASDA1/ASCL1 pins
Alternate I2C2 pins
1 = I2C2 mapped to SDA2/SCL2 pins
0 = I2C2 mapped to ASDA2/ASCL2 pins
JTAGEN
JTAG Enable bit
1 = JTAG enabled
0 = JTAG disabled
ICS<1:0>
ICD Communication Channel Select bits
11 = Communicate on PGEC1 and PGED1
10 = Communicate on PGEC2 and PGED2
01 = Communicate on PGEC3 and PGED3
00 = Reserved, do not use
Note 1: This bit is only available on dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices.
ALTI2C2
DS70657E-page 378
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
REGISTER 27-1:
R
DEVID: DEVICE ID REGISTER
R
R
R
R
DEVID<23:16>
R
R
R
bit 23
bit 16
R
R
R
R
R
DEVID<15:8>
R
R
R
bit 15
bit 8
R
R
R
R
R
R
R
R
DEVID<7:0>
bit 7
bit 0
Legend: R = Read-Only bit
bit 23-0
Note 1:
DEVID<23:0>: Device Identifier bits(1)
Refer to the “dsPIC33E/PIC24E Flash Programming Specification for Devices with Volatile Configuration
Bits” (DS70663) for the list of device ID values.
REGISTER 27-2:
R
U = Unimplemented bit
DEVREV: DEVICE REVISION REGISTER
R
R
R
R
DEVREV<23:16>
R
R
R
bit 23
bit 16
R
R
R
R
R
DEVREV<15:8>
R
R
R
bit 15
bit 8
R
R
R
R
R
DEVREV<7:0>
R
bit 7
Note 1:
R
bit 0
Legend: R = Read-only bit
bit 23-0
R
U = Unimplemented bit
DEVREV<23:0>: Device Revision bits(1)
Refer to the “dsPIC33E/PIC24E Flash Programming Specification for Devices with Volatile Configuration
Bits” (DS70663) for the list of device revision values.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 379
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
27.2
User ID Words
FIGURE 27-1:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices contain four
User ID Words, located at addresses 0x800FF8
through 0x800FFE. The User ID Words can be used for
storing product information such as serial numbers,
system manufacturing dates, manufacturing lot
numbers and other application-specific information.
3.3V
dsPIC33E/PIC24E
VDD
The User ID Words register map is shown in
Table 27-3.
TABLE 27-3:
File Name
VCAP
CEFC
USER ID WORDS REGISTER
MAP
Address
Bit 23-16
Bit 15-0
FUID0
0x800FF8
—
UID0
FUID1
0x800FFA
—
UID1
FUID2
0x800FFC
—
UID2
FUID3
0x800FFE
—
UID3
These are typical operating voltages. Refer to
Table 30-5 located in Section 30.1 “DC Characteristics” for the full operating ranges of
VDD and VCAP.
2:
It is important for the low-ESR capacitor to be
placed as close as possible to the VCAP pin.
3:
Typical VCAP pin voltage = 1.8V when
VDD ≥ VDDMIN.
On-Chip Voltage Regulator
All
of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X devices power their core digital logic at a
nominal 1.8V. This can create a conflict for designs that
are required to operate at a higher typical voltage, such
as 3.3V. To simplify system design, all devices in the
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X family incorporate an onchip regulator that allows the device to run its core logic
from VDD.
The regulator provides power to the core from the other
VDD pins. A low-ESR (less than 1 Ohm) capacitor (such
as tantalum or ceramic) must be connected to the VCAP
pin (Figure 27-1). This helps to maintain the stability of
the regulator. The recommended value for the filter
capacitor is provided in Table 30-5 located in
Section 30.0 “Electrical Characteristics”.
Note:
It is important for the low-ESR capacitor to
be placed as close as possible to the VCAP
pin.
VSS
Note 1:
Legend: — = unimplemented, read as ‘1’.
27.3
CONNECTIONS FOR THE
ON-CHIP VOLTAGE
REGULATOR(1,2,3)
27.4
Brown-out Reset (BOR)
The Brown-out Reset (BOR) module is based on an
internal voltage reference circuit that monitors the regulated supply voltage VCAP. The main purpose of the
BOR module is to generate a device Reset when a
brown-out condition occurs. Brown-out conditions are
generally caused by glitches on the AC mains (for
example, missing portions of the AC cycle waveform
due to bad power transmission lines, or voltage sags
due to excessive current draw when a large inductive
load is turned on).
A BOR generates a Reset pulse, which resets the
device. The BOR selects the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>).
If an oscillator mode is selected, the BOR activates the
Oscillator Start-up Timer (OST). The system clock is
held until OST expires. If the PLL is used, the clock is
held until the LOCK bit (OSCCON<5>) is ‘1’.
Concurrently, the PWRT time-out (TPWRT) is applied
before the internal Reset is released. If TPWRT = 0 and
a crystal oscillator is being used, then a nominal delay
of TFSCM is applied. The total delay in this case is
TFSCM. Refer to parameter SY35 in Table 30-21 of
Section 30.0 “Electrical Characteristics” for specific
TFSCM values.
The BOR Status bit (RCON<1>) is set to indicate that a
BOR has occurred. The BOR circuit, continues to operate while in Sleep or Idle modes and resets the device
should VDD fall below the BOR threshold voltage.
DS70657E-page 380
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
27.5
Watchdog Timer (WDT)
27.5.2
For dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices, the WDT
is driven by the LPRC oscillator. When the WDT is
enabled, the clock source is also enabled.
27.5.1
PRESCALER/POSTSCALER
The nominal WDT clock source from LPRC is 32 kHz.
This feeds a prescaler that can be configured for either
5-bit (divide-by-32) or 7-bit (divide-by-128) operation.
The prescaler is set by the WDTPRE Configuration bit.
With a 32 kHz input, the prescaler yields a WDT timeout period (TWDT), as shown in parameter SY12 in
Table 30-21.
A variable postscaler divides down the WDT prescaler
output and allows for a wide range of time-out periods.
The postscaler is controlled by the WDTPOST<3:0>
Configuration bits (FWDT<3:0>), which allow the selection of 16 settings, from 1:1 to 1:32,768. Using the prescaler and postscaler, time-out periods ranging from
1 ms to 131 seconds can be achieved.
The WDT, prescaler and postscaler are reset:
• On any device Reset
• On the completion of a clock switch, whether
invoked by software (i.e., setting the OSWEN bit
after changing the NOSC bits) or by hardware
(i.e., Fail-Safe Clock Monitor)
• When a PWRSAV instruction is executed
(i.e., Sleep or Idle mode is entered)
• When the device exits Sleep or Idle mode to
resume normal operation
• By a CLRWDT instruction during normal execution
Note:
SLEEP AND IDLE MODES
If the WDT is enabled, it continues to run during Sleep or
Idle modes. When the WDT time-out occurs, the device
wakes the device and code execution continues from
where the PWRSAV instruction was executed. The corresponding SLEEP or IDLE bits (RCON<3,2>) needs to be
cleared in software after the device wakes up.
27.5.3
ENABLING WDT
The WDT is enabled or disabled by the FWDTEN
Configuration bit in the FWDT Configuration register.
When the FWDTEN Configuration bit is set, the WDT is
always enabled.
The WDT can be optionally controlled in software
when the FWDTEN Configuration bit has been
programmed to ‘0’. The WDT is enabled in software
by setting the SWDTEN control bit (RCON<5>). The
SWDTEN control bit is cleared on any device Reset.
The software WDT option allows the user application
to enable the WDT for critical code segments and
disable the WDT during non-critical segments for
maximum power savings.
The WDT flag bit, WDTO (RCON<4>), is not automatically
cleared following a WDT time-out. To detect subsequent
WDT events, the flag must be cleared in software.
27.5.4
WDT WINDOW
The Watchdog Timer has an optional Windowed mode
enabled by programming the WINDIS bit in the WDT
configuration register (FWDT<6>). In the Windowed
mode (WINDIS = 0), the WDT should be cleared based
on the settings in the programmable watchdog window
select bits (WDTWIN<1:0>).
The CLRWDT and PWRSAV instructions
clear the prescaler and postscaler counts
when executed.
FIGURE 27-2:
WDT BLOCK DIAGRAM
All Device Resets
Transition to New Clock Source
Exit Sleep or Idle Mode
PWRSAV Instruction
CLRWDT Instruction
Watchdog Timer
Sleep/Idle
WDTPRE
SWDTEN
FWDTEN
WDTPOST<3:0>
RS
Prescaler
(divide by N1)
LPRC Clock
WDT
Wake-up
1
RS
Postscaler
(divide by N2)
0
WINDIS
WDT
Reset
WDT Window Select
WDTWIN<1:0>
CLRWDT Instruction
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 381
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
27.6
JTAG Interface
27.8
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X devices implement a
JTAG interface, which supports boundary scan device
testing. Detailed information on this interface is
provided in future revisions of the document.
Note:
27.7
Refer to Section 24. “Programming and
Diagnostics”
(DS70608)
of
the
“dsPIC33E/PIC24E Family Reference
Manual” for further information on usage,
configuration and operation of the JTAG
interface.
In-Circuit Serial Programming
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices can be
serially programmed while in the end application circuit.
This is done with two lines for clock and data and three
other lines for power, ground and the programming
sequence. Serial programming allows customers to
manufacture boards with unprogrammed devices and
then program the device just before shipping the
product. Serial programming also allows the most recent
firmware or a custom firmware to be programmed. Refer
to the “dsPIC33E/PIC24E Flash Programming
Specification for Devices with Volatile Configuration Bits”
(DS70663) for details about In-Circuit Serial
Programming (ICSP).
Any of the three pairs of programming clock/data pins
can be used:
When MPLAB® ICD 3 or REAL ICE™ is selected as a
debugger, the in-circuit debugging functionality is
enabled. This function allows simple debugging functions when used with MPLAB IDE. Debugging functionality is controlled through the PGECx (Emulation/
Debug Clock) and PGEDx (Emulation/Debug Data) pin
functions.
Any of the three pairs of debugging clock/data pins can
be used:
• PGEC1 and PGED1
• PGEC2 and PGED2
• PGEC3 and PGED3
To use the in-circuit debugger function of the device,
the design must implement ICSP connections to
MCLR, VDD, VSS, and the PGECx/PGEDx pin pair. In
addition, when the feature is enabled, some of the
resources are not available for general use. These
resources include the first 80 bytes of data RAM and
two I/O pins (PGECx and PGEDx).
27.9
Code Protection and
CodeGuard™ Security
The dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/
50X, and PIC24EPXXXGP/MC20X devices offer basic
implementation of CodeGuard Security that supports
only General Segment (GS) security. This feature helps
protect individual Intellectual Property.
Note:
• PGEC1 and PGED1
• PGEC2 and PGED2
• PGEC3 and PGED3
DS70657E-page 382
In-Circuit Debugger
Preliminary
Refer to Section 23. “CodeGuard™
Security” (DS70634) of the “dsPIC33E/
PIC24E Family Reference Manual” for
further
information
on
usage,
configuration
and
operation
of
CodeGuard Security.
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
28.0
Note:
INSTRUCTION SET SUMMARY
This data sheet summarizes the features of
the
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X,
and
PIC24EPXXXGP/MC20X
families
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to the related section of the
“dsPIC33E/PIC24E
Family
Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
The dsPIC33EP instruction set is almost identical to
that of the dsPIC30F and dsPIC33F. The PIC24EP
instruction set is almost identical to that of the PIC24F
and PIC24H.
Most instructions are a single program memory word
(24 bits). Only three instructions require two program
memory locations.
Most bit-oriented instructions (including simple rotate/
shift instructions) have two operands:
• The W register (with or without an address
modifier) or file register (specified by the value of
‘Ws’ or ‘f’)
• The bit in the W register or file register (specified
by a literal value or indirectly by the contents of
register ‘Wb’)
The literal instructions that involve data movement can
use some of the following operands:
• A literal value to be loaded into a W register or file
register (specified by ‘k’)
• The W register or file register where the literal
value is to be loaded (specified by ‘Wb’ or ‘f’)
However, literal instructions that involve arithmetic or
logical operations use some of the following operands:
Each single-word instruction is a 24-bit word, divided
into an 8-bit opcode, which specifies the instruction
type and one or more operands, which further specify
the operation of the instruction.
• The first source operand, which is a register ‘Wb’
without any address modifier
• The second source operand, which is a literal
value
• The destination of the result (only if not the same
as the first source operand), which is typically a
register ‘Wd’ with or without an address modifier
The instruction set is highly orthogonal and is grouped
into five basic categories:
The MAC class of DSP instructions can use some of the
following operands:
•
•
•
•
•
• The accumulator (A or B) to be used (required
operand)
• The W registers to be used as the two operands
• The X and Y address space prefetch operations
• The X and Y address space prefetch destinations
• The accumulator write back destination
Word or byte-oriented operations
Bit-oriented operations
Literal operations
DSP operations
Control operations
Table 28-1 lists the general symbols used in describing
the instructions.
The dsPIC33E instruction set summary in Table 28-2
lists all the instructions, along with the status flags
affected by each instruction.
Most word or byte-oriented W register instructions
(including barrel shift instructions) have three
operands:
• The first source operand, which is typically a
register ‘Wb’ without any address modifier
• The second source operand, which is typically a
register ‘Ws’ with or without an address modifier
• The destination of the result, which is typically a
register ‘Wd’ with or without an address modifier
The other DSP instructions do not involve any
multiplication and can include:
• The accumulator to be used (required)
• The source or destination operand (designated as
Wso or Wdo, respectively) with or without an
address modifier
• The amount of shift specified by a W register ‘Wn’
or a literal value
The control instructions can use some of the following
operands:
• A program memory address
• The mode of the table read and table write
instructions
However, word or byte-oriented file register instructions
have two operands:
• The file register specified by the value ‘f’
• The destination, which could be either the file
register ‘f’ or the W0 register, which is denoted as
‘WREG’
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 383
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Most instructions are a single word. Certain doubleword instructions are designed to provide all the
required information in these 48 bits. In the second
word, the 8 MSbs are ‘0’s. If this second word is executed as an instruction (by itself), it executes as a NOP.
The double-word instructions execute in two instruction
cycles.
Most single-word instructions are executed in a single
instruction cycle, unless a conditional test is true, or the
program counter is changed as a result of the
instruction, or a PSV or table read is performed. In these
cases, the execution takes multiple instruction cycles
TABLE 28-1:
with the additional instruction cycle(s) executed as a
NOP. Certain instructions that involve skipping over the
subsequent instruction require either two or three cycles
if the skip is performed, depending on whether the
instruction being skipped is a single-word or two-word
instruction. Moreover, double-word moves require two
cycles.
Note:
For more details on the instruction set,
refer to the “16-bit MCU and DSC
Programmer’s
Reference
Manual”
(DS70157).
SYMBOLS USED IN OPCODE DESCRIPTIONS
Field
Description
#text
Means literal defined by “text”
(text)
Means “content of text”
[text]
Means “the location addressed by text”
{}
Optional field or operation
a ∈ {b, c, d}
a is selected from the set of values b, c, d
<n:m>
Register bit field
.b
Byte mode selection
.d
Double-Word mode selection
.S
Shadow register select
.w
Word mode selection (default)
Acc
One of two accumulators {A, B}
AWB
Accumulator write back destination address register ∈ {W13, [W13]+ = 2}
bit4
4-bit bit selection field (used in word addressed instructions) ∈ {0...15}
C, DC, N, OV, Z
MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero
Expr
Absolute address, label or expression (resolved by the linker)
f
File register address ∈ {0x0000...0x1FFF}
lit1
1-bit unsigned literal ∈ {0,1}
lit4
4-bit unsigned literal ∈ {0...15}
lit5
5-bit unsigned literal ∈ {0...31}
lit8
8-bit unsigned literal ∈ {0...255}
lit10
10-bit unsigned literal ∈ {0...255} for Byte mode, {0:1023} for Word mode
lit14
14-bit unsigned literal ∈ {0...16384}
lit16
16-bit unsigned literal ∈ {0...65535}
lit23
23-bit unsigned literal ∈ {0...8388608}; LSb must be ‘0’
None
Field does not require an entry, can be blank
OA, OB, SA, SB
DSP Status bits: ACCA Overflow, ACCB Overflow, ACCA Saturate, ACCB Saturate
PC
Program Counter
Slit10
10-bit signed literal ∈ {-512...511}
Slit16
16-bit signed literal ∈ {-32768...32767}
Slit6
6-bit signed literal ∈ {-16...16}
Wb
Base W register ∈ {W0...W15}
Wd
Destination W register ∈ { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] }
Wdo
Destination W register ∈
{ Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] }
Wm,Wn
Dividend, Divisor working register pair (direct addressing)
DS70657E-page 384
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-1:
SYMBOLS USED IN OPCODE DESCRIPTIONS (CONTINUED)
Field
Description
Wm*Wm
Multiplicand and Multiplier working register pair for Square instructions ∈
{W4 * W4,W5 * W5,W6 * W6,W7 * W7}
Wm*Wn
Multiplicand and Multiplier working register pair for DSP instructions ∈
{W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7}
Wn
One of 16 working registers ∈ {W0...W15}
Wnd
One of 16 destination working registers ∈ {W0...W15}
Wns
One of 16 source working registers ∈ {W0...W15}
WREG
W0 (working register used in file register instructions)
Ws
Source W register ∈ { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] }
Wso
Source W register ∈
{ Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] }
Wx
X data space prefetch address register for DSP instructions
∈ {[W8] + = 6, [W8] + = 4, [W8] + = 2, [W8], [W8] - = 6, [W8] - = 4, [W8] - = 2,
[W9] + = 6, [W9] + = 4, [W9] + = 2, [W9], [W9] - = 6, [W9] - = 4, [W9] - = 2,
[W9 + W12], none}
Wxd
X data space prefetch destination register for DSP instructions ∈ {W4...W7}
Wy
Y data space prefetch address register for DSP instructions
∈ {[W10] + = 6, [W10] + = 4, [W10] + = 2, [W10], [W10] - = 6, [W10] - = 4, [W10] - = 2,
[W11] + = 6, [W11] + = 4, [W11] + = 2, [W11], [W11] - = 6, [W11] - = 4, [W11] - = 2,
[W11 + W12], none}
Wyd
Y data space prefetch destination register for DSP instructions ∈ {W4...W7}
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 385
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-2:
Base
Instr
#
Assembly
Mnemonic
1
ADD
2
3
4
5
6
7
8
Note
ADDC
AND
ASR
BCLR
BRA
BSET
BSW
1:
INSTRUCTION SET OVERVIEW
Assembly Syntax
# of
# of
Status Flags
Words Cycles
Affected
Description
ADD
Acc(1)
Add Accumulators
ADD
f
f = f + WREG
1
1
C,DC,N,OV,Z
ADD
f,WREG
WREG = f + WREG
1
1
C,DC,N,OV,Z
ADD
#lit10,Wn
Wd = lit10 + Wd
1
1
C,DC,N,OV,Z
ADD
Wb,Ws,Wd
Wd = Wb + Ws
1
1
C,DC,N,OV,Z
ADD
Wb,#lit5,Wd
Wd = Wb + lit5
1
1
C,DC,N,OV,Z
ADD
Wso,#Slit4,Acc
16-bit Signed Add to Accumulator
1
1
OA,OB,SA,S
B
ADDC
f
f = f + WREG + (C)
1
1
C,DC,N,OV,Z
ADDC
f,WREG
WREG = f + WREG + (C)
1
1
C,DC,N,OV,Z
ADDC
#lit10,Wn
Wd = lit10 + Wd + (C)
1
1
C,DC,N,OV,Z
ADDC
Wb,Ws,Wd
Wd = Wb + Ws + (C)
1
1
C,DC,N,OV,Z
ADDC
Wb,#lit5,Wd
Wd = Wb + lit5 + (C)
1
1
C,DC,N,OV,Z
AND
f
f = f .AND. WREG
1
1
N,Z
AND
f,WREG
WREG = f .AND. WREG
1
1
N,Z
AND
#lit10,Wn
Wd = lit10 .AND. Wd
1
1
N,Z
AND
Wb,Ws,Wd
Wd = Wb .AND. Ws
1
1
N,Z
1
1
OA,OB,SA,S
B
AND
Wb,#lit5,Wd
Wd = Wb .AND. lit5
1
1
N,Z
ASR
f
f = Arithmetic Right Shift f
1
1
C,N,OV,Z
ASR
f,WREG
WREG = Arithmetic Right Shift f
1
1
C,N,OV,Z
ASR
Ws,Wd
Wd = Arithmetic Right Shift Ws
1
1
C,N,OV,Z
ASR
Wb,Wns,Wnd
Wnd = Arithmetic Right Shift Wb by Wns
1
1
N,Z
ASR
Wb,#lit5,Wnd
Wnd = Arithmetic Right Shift Wb by lit5
1
1
N,Z
BCLR
f,#bit4
Bit Clear f
1
1
None
BCLR
Ws,#bit4
Bit Clear Ws
1
1
None
BRA
C,Expr
Branch if Carry
1
1 (4)
None
BRA
GE,Expr
Branch if greater than or equal
1
1 (4)
None
BRA
GEU,Expr
Branch if unsigned greater than or equal
1
1 (4)
None
BRA
GT,Expr
Branch if greater than
1
1 (4)
None
BRA
GTU,Expr
Branch if unsigned greater than
1
1 (4)
None
BRA
LE,Expr
Branch if less than or equal
1
1 (4)
None
BRA
LEU,Expr
Branch if unsigned less than or equal
1
1 (4)
None
BRA
LT,Expr
Branch if less than
1
1 (4)
None
BRA
LTU,Expr
Branch if unsigned less than
1
1 (4)
None
BRA
N,Expr
Branch if Negative
1
1 (4)
None
BRA
NC,Expr
Branch if Not Carry
1
1 (4)
None
BRA
NN,Expr
Branch if Not Negative
1
1 (4)
None
BRA
NOV,Expr
Branch if Not Overflow
1
1 (4)
None
BRA
NZ,Expr
Branch if Not Zero
1
1 (4)
None
BRA
OA,Expr(1)
Branch if Accumulator A overflow
1
1 (4)
None
BRA
OB,Expr(1)
Branch if Accumulator B overflow
1
1 (4)
None
BRA
OV,Expr(1)
Branch if Overflow
1
1 (4)
None
BRA
SA,Expr(1)
Branch if Accumulator A saturated
1
1 (4)
None
BRA
SB,Expr(1)
Branch if Accumulator B saturated
1
1 (4)
None
BRA
Expr
Branch Unconditionally
1
4
None
BRA
Z,Expr
Branch if Zero
1
1 (4)
None
BRA
Wn
Computed Branch
1
4
None
BSET
f,#bit4
Bit Set f
1
1
None
BSET
Ws,#bit4
Bit Set Ws
1
1
None
BSW.C
Ws,Wb
Write C bit to Ws<Wb>
1
1
None
BSW.Z
Ws,Wb
Write Z bit to Ws<Wb>
1
1
None
This instruction is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
DS70657E-page 386
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-2:
Base
Instr
#
Assembly
Mnemonic
9
BTG
10
11
12
13
14
15
BTSC
BTSS
BTST
BTSTS
CALL
CLR
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly Syntax
Description
# of
# of
Status Flags
Words Cycles
Affected
BTG
f,#bit4
Bit Toggle f
1
1
None
BTG
Ws,#bit4
Bit Toggle Ws
1
1
None
BTSC
f,#bit4
Bit Test f, Skip if Clear
1
1
(2 or 3)
None
BTSC
Ws,#bit4
Bit Test Ws, Skip if Clear
1
1
(2 or 3)
None
BTSS
f,#bit4
Bit Test f, Skip if Set
1
1
(2 or 3)
None
BTSS
Ws,#bit4
Bit Test Ws, Skip if Set
1
1
(2 or 3)
None
BTST
f,#bit4
Bit Test f
1
1
Z
BTST.C
Ws,#bit4
Bit Test Ws to C
1
1
C
BTST.Z
Ws,#bit4
Bit Test Ws to Z
1
1
Z
BTST.C
Ws,Wb
Bit Test Ws<Wb> to C
1
1
C
Z
BTST.Z
Ws,Wb
Bit Test Ws<Wb> to Z
1
1
BTSTS
f,#bit4
Bit Test then Set f
1
1
Z
BTSTS.C
Ws,#bit4
Bit Test Ws to C, then Set
1
1
C
BTSTS.Z
Ws,#bit4
Bit Test Ws to Z, then Set
1
1
Z
CALL
lit23
Call subroutine
2
4
SFA
CALL
Wn
Call indirect subroutine
1
4
SFA
CALL.L
Wn
Call indirect subroutine (long address)
1
4
SFA
CLR
f
f = 0x0000
1
1
None
CLR
WREG
WREG = 0x0000
1
1
None
CLR
Ws
Ws = 0x0000
1
1
None
CLR
Acc,Wx,Wxd,Wy,Wyd,AWB(1)
Clear Accumulator
1
1
OA,OB,SA,S
B
Clear Watchdog Timer
1
1
WDTO,Sleep
16
CLRWDT
CLRWDT
17
COM
COM
f
f=f
1
1
N,Z
COM
f,WREG
WREG = f
1
1
N,Z
COM
Ws,Wd
Wd = Ws
1
1
N,Z
CP
f
Compare f with WREG
1
1
C,DC,N,OV,Z
CP
Wb,#lit8
Compare Wb with lit8
1
1
C,DC,N,OV,Z
CP
Wb,Ws
Compare Wb with Ws (Wb – Ws)
1
1
C,DC,N,OV,Z
CP0
f
Compare f with 0x0000
1
1
C,DC,N,OV,Z
CP0
Ws
Compare Ws with 0x0000
1
1
C,DC,N,OV,Z
CPB
f
Compare f with WREG, with Borrow
1
1
C,DC,N,OV,Z
CPB
Wb,#lit8
Compare Wb with lit8, with Borrow
1
1
C,DC,N,OV,Z
CPB
Wb,Ws
Compare Wb with Ws, with Borrow
(Wb – Ws – C)
1
1
C,DC,N,OV,Z
CPSEQ
CPSEQ
Wb,Wn
Compare Wb with Wn, skip if =
1
1
(2 or 3)
None
CPBEQ
CPBEQ
Wb,Wn,Expr
Compare Wb with Wn, branch if =
1
1 (5)
None
CPSGT
CPSGT
Wb,Wn
Compare Wb with Wn, skip if >
1
1
(2 or 3)
None
CPBGT
CPBGT
Wb,Wn,Expr
Compare Wb with Wn, branch if >
1
1 (5)
None
CPSLT
CPSLT
Wb,Wn
Compare Wb with Wn, skip if <
1
1
(2 or 3)
None
CPBLT
CPBLT
Wb,Wn,Expr
Compare Wb with Wn, branch if <
1
1 (5)
None
CPSNE
CPSNE
Wb,Wn
Compare Wb with Wn, skip if ≠
1
1
(2 or 3)
None
CPBNE
CPBNE
Wb,Wn,Expr
Compare Wb with Wn, branch if ≠
1
1 (5)
None
18
19
20
21
22
23
24
Note
CP
CP0
CPB
1:
This instruction is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 387
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-2:
INSTRUCTION SET OVERVIEW (CONTINUED)
Base
Instr
#
Assembly
Mnemonic
25
DAW
DAW
Wn
Wn = decimal adjust Wn
1
1
C
26
DEC
DEC
f
f=f–1
1
1
C,DC,N,OV,Z
DEC
f,WREG
WREG = f – 1
1
1
C,DC,N,OV,Z
DEC
Ws,Wd
Wd = Ws – 1
1
1
C,DC,N,OV,Z
DEC2
f
f=f–2
1
1
C,DC,N,OV,Z
DEC2
f,WREG
WREG = f – 2
1
1
C,DC,N,OV,Z
DEC2
Ws,Wd
Wd = Ws – 2
1
1
C,DC,N,OV,Z
27
DEC2
Assembly Syntax
# of
# of
Status Flags
Words Cycles
Affected
Description
28
DISI
DISI
#lit14
Disable Interrupts for k instruction cycles
1
1
None
29
DIV
DIV.S
Wm,Wn
Signed 16/16-bit Integer Divide
1
18
N,Z,C,OV
DIV.SD
Wm,Wn
Signed 32/16-bit Integer Divide
1
18
N,Z,C,OV
DIV.U
Wm,Wn
Unsigned 16/16-bit Integer Divide
1
18
N,Z,C,OV
DIV.UD
Wm,Wn
Unsigned 32/16-bit Integer Divide
1
18
N,Z,C,OV
30
DIVF
DIVF
Wm,Wn(1)
Signed 16/16-bit Fractional Divide
1
18
N,Z,C,OV
31
DO
DO
#lit15,Expr(1)
Do code to PC + Expr, lit15 + 1 times
2
2
None
DO
Wn,Expr(1)
Do code to PC + Expr, (Wn) + 1 times
2
2
None
32
ED
ED
Wm*Wm,Acc,Wx,Wy,Wxd(1)
Euclidean Distance (no accumulate)
1
1
OA,OB,OAB,
SA,SB,SAB
33
EDAC
EDAC
Wm*Wm,Acc,Wx,Wy,Wxd(1)
Euclidean Distance
1
1
OA,OB,OAB,
SA,SB,SAB
34
EXCH
EXCH
Wns,Wnd
Swap Wns with Wnd
1
1
None
35
FBCL
FBCL
Ws,Wnd
Find Bit Change from Left (MSb) Side
1
1
C
36
FF1L
FF1L
Ws,Wnd
Find First One from Left (MSb) Side
1
1
C
37
FF1R
FF1R
Ws,Wnd
Find First One from Right (LSb) Side
1
1
C
38
GOTO
GOTO
Expr
Go to address
2
4
None
GOTO
Wn
Go to indirect
1
4
None
39
40
41
INC
INC2
IOR
GOTO.L
Wn
Go to indirect (long address)
1
4
None
INC
f
f=f+1
1
1
C,DC,N,OV,Z
INC
f,WREG
WREG = f + 1
1
1
C,DC,N,OV,Z
INC
Ws,Wd
Wd = Ws + 1
1
1
C,DC,N,OV,Z
INC2
f
f=f+2
1
1
C,DC,N,OV,Z
INC2
f,WREG
WREG = f + 2
1
1
C,DC,N,OV,Z
INC2
Ws,Wd
Wd = Ws + 2
1
1
C,DC,N,OV,Z
IOR
f
f = f .IOR. WREG
1
1
N,Z
IOR
f,WREG
WREG = f .IOR. WREG
1
1
N,Z
IOR
#lit10,Wn
Wd = lit10 .IOR. Wd
1
1
N,Z
IOR
Wb,Ws,Wd
Wd = Wb .IOR. Ws
1
1
N,Z
IOR
Wb,#lit5,Wd
Wd = Wb .IOR. lit5
1
1
N,Z
42
LAC
LAC
Wso,#Slit4,Acc
Load Accumulator
1
1
OA,OB,OAB,
SA,SB,SAB
43
LNK
LNK
#lit14
Link Frame Pointer
1
1
SFA
44
LSR
LSR
f
f = Logical Right Shift f
1
1
C,N,OV,Z
LSR
f,WREG
WREG = Logical Right Shift f
1
1
C,N,OV,Z
LSR
Ws,Wd
Wd = Logical Right Shift Ws
1
1
C,N,OV,Z
LSR
Wb,Wns,Wnd
Wnd = Logical Right Shift Wb by Wns
1
1
N,Z
LSR
Wb,#lit5,Wnd
Wnd = Logical Right Shift Wb by lit5
1
1
N,Z
MAC
Wm*Wn,Acc,Wx,Wxd,Wy,Wyd,AWB(1)
Multiply and Accumulate
1
1
OA,OB,OAB,
SA,SB,SAB
MAC
Wm*Wm,Acc,Wx,Wxd,Wy,Wyd(1)
Square and Accumulate
1
1
OA,OB,OAB,
SA,SB,SAB
45
Note
MAC
1:
This instruction is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
DS70657E-page 388
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-2:
Base
Instr
#
Assembly
Mnemonic
46
MOV
47
MOVPAG
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly Syntax
Description
# of
# of
Status Flags
Words Cycles
Affected
MOV
f,Wn
Move f to Wn
1
1
None
MOV
f
Move f to f
1
1
None
MOV
f,WREG
Move f to WREG
1
1
None
MOV
#lit16,Wn
Move 16-bit literal to Wn
1
1
None
MOV.b
#lit8,Wn
Move 8-bit literal to Wn
1
1
None
MOV
Wn,f
Move Wn to f
1
1
None
MOV
Wso,Wdo
Move Ws to Wd
1
1
None
MOV
WREG,f
Move WREG to f
1
1
None
MOV.D
Wns,Wd
Move Double from W(ns):W(ns + 1) to Wd
1
2
None
MOV.D
Ws,Wnd
Move Double from Ws to W(nd + 1):W(nd)
1
2
None
MOVPAG
#lit10,DSRPAG
Move 10-bit literal to DSRPAG
1
1
None
MOVPAG
#lit9,DSWPAG
Move 9-bit literal to DSWPAG
1
1
None
MOVPAG
#lit8,TBLPAG
Move 8-bit literal to TBLPAG
1
1
None
MOVPAGW
Ws, DSRPAG
Move Ws<9:0> to DSRPAG
1
1
None
MOVPAGW
Ws, DSWPAG
Move Ws<8:0> to DSWPAG
1
1
None
MOVPAGW
Ws, TBLPAG
Move Ws<7:0> to TBLPAG
1
1
None
48
MOVSAC
MOVSAC
Acc,Wx,Wxd,Wy,Wyd,AWB(1)
Prefetch and store accumulator
1
1
None
49
MPY
MPY
Wm*Wn,Acc,Wx,Wxd,Wy,Wyd(1)
Multiply Wm by Wn to Accumulator
1
1
OA,OB,OAB,
SA,SB,SAB
MPY
Wm*Wm,Acc,Wx,Wxd,Wy,Wyd(1)
Square Wm to Accumulator
1
1
OA,OB,OAB,
SA,SB,SAB
50
MPY.N
MPY.N
Wm*Wn,Acc,Wx,Wxd,Wy,Wyd(1)
-(Multiply Wm by Wn) to Accumulator
1
1
None
51
MSC
MSC
Wm*Wm,Acc,Wx,Wxd,Wy,Wyd,AWB(1)
Multiply and Subtract from Accumulator
1
1
OA,OB,OAB,
SA,SB,SAB
52
MUL
MUL.SS
Wb,Ws,Wnd
{Wnd + 1, Wnd} = signed(Wb) *
signed(Ws)
1
1
None
MUL.SS
Wb,Ws,Acc(1)
Accumulator = signed(Wb) * signed(Ws)
1
1
None
MUL.SU
Wb,Ws,Wnd
{Wnd + 1, Wnd} = signed(Wb) *
unsigned(Ws)
1
1
None
MUL.SU
Wb,Ws,Acc(1)
Accumulator = signed(Wb) *
unsigned(Ws)
1
1
None
Note
1:
MUL.SU
Wb,#lit5,Acc(1)
Accumulator = signed(Wb) * unsigned(lit5)
1
1
None
MUL.US
Wb,Ws,Wnd
{Wnd + 1, Wnd} = unsigned(Wb) *
signed(Ws)
1
1
None
MUL.US
Wb,Ws,Acc(1)
Accumulator = unsigned(Wb) *
signed(Ws)
1
1
None
MUL.UU
Wb,Ws,Wnd
{Wnd + 1, Wnd} = unsigned(Wb) *
unsigned(Ws)
1
1
None
MUL.UU
Wb,#lit5,Acc(1)
Accumulator = unsigned(Wb) *
unsigned(lit5)
1
1
None
MUL.UU
Wb,Ws,Acc(1)
Accumulator = unsigned(Wb) *
unsigned(Ws)
1
1
None
MULW.SS
Wb,Ws,Wnd
Wnd = signed(Wb) * signed(Ws)
1
1
None
MULW.SU
Wb,Ws,Wnd
Wnd = signed(Wb) * unsigned(Ws)
1
1
None
MULW.US
Wb,Ws,Wnd
Wnd = unsigned(Wb) * signed(Ws)
1
1
None
MULW.UU
Wb,Ws,Wnd
Wnd = unsigned(Wb) * unsigned(Ws)
1
1
None
MUL.SU
Wb,#lit5,Wnd
{Wnd + 1, Wnd} = signed(Wb) *
unsigned(lit5)
1
1
None
MUL.SU
Wb,#lit5,Wnd
Wnd = signed(Wb) * unsigned(lit5)
1
1
None
MUL.UU
Wb,#lit5,Wnd
{Wnd + 1, Wnd} = unsigned(Wb) *
unsigned(lit5)
1
1
None
MUL.UU
Wb,#lit5,Wnd
Wnd = unsigned(Wb) * unsigned(lit5)
1
1
None
MUL
f
W3:W2 = f * WREG
1
1
None
This instruction is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 389
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-2:
Base
Instr
#
Assembly
Mnemonic
53
NEG
54
55
NOP
POP
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly Syntax
NEG
Acc(1)
Negate Accumulator
1
1
OA,OB,OAB,
SA,SB,SAB
NEG
f
f=f+1
1
1
C,DC,N,OV,Z
NEG
f,WREG
WREG = f + 1
1
1
C,DC,N,OV,Z
NEG
Ws,Wd
Wd = Ws + 1
1
1
C,DC,N,OV,Z
NOP
No Operation
1
1
None
NOPR
No Operation
1
1
None
f
Pop f from Top-of-Stack (TOS)
1
1
None
POP
Wdo
Pop from Top-of-Stack (TOS) to Wdo
1
1
None
POP.D
Wnd
Pop from Top-of-Stack (TOS) to
W(nd):W(nd + 1)
1
2
None
POP
Pop Shadow Registers
1
1
All
f
Push f to Top-of-Stack (TOS)
1
1
None
PUSH
Wso
Push Wso to Top-of-Stack (TOS)
1
1
None
PUSH.D
Wns
Push W(ns):W(ns + 1) to Top-of-Stack
(TOS)
1
2
None
POP.S
56
PUSH
# of
# of
Status Flags
Words Cycles
Affected
Description
PUSH
PUSH.S
Push Shadow Registers
1
1
None
Go into Sleep or Idle mode
1
1
WDTO,Sleep
57
PWRSAV
PWRSAV
58
RCALL
RCALL
Expr
Relative Call
1
4
SFA
RCALL
Wn
Computed Call
1
4
SFA
REPEAT
#lit15
Repeat Next Instruction lit15 + 1 times
1
1
None
REPEAT
Wn
Repeat Next Instruction (Wn) + 1 times
1
1
None
None
59
REPEAT
#lit1
60
RESET
RESET
Software device Reset
1
1
61
RETFIE
RETFIE
Return from interrupt
1
6 (5)
SFA
62
RETLW
RETLW
Return with literal in Wn
1
6 (5)
SFA
63
RETURN
RETURN
Return from Subroutine
1
6 (5)
SFA
64
RLC
RLC
f
f = Rotate Left through Carry f
1
1
C,N,Z
RLC
f,WREG
WREG = Rotate Left through Carry f
1
1
C,N,Z
RLC
Ws,Wd
Wd = Rotate Left through Carry Ws
1
1
C,N,Z
RLNC
f
f = Rotate Left (No Carry) f
1
1
N,Z
RLNC
f,WREG
WREG = Rotate Left (No Carry) f
1
1
N,Z
65
66
67
68
RLNC
RRC
RRNC
SAC
#lit10,Wn
RLNC
Ws,Wd
Wd = Rotate Left (No Carry) Ws
1
1
N,Z
RRC
f
f = Rotate Right through Carry f
1
1
C,N,Z
RRC
f,WREG
WREG = Rotate Right through Carry f
1
1
C,N,Z
RRC
Ws,Wd
Wd = Rotate Right through Carry Ws
1
1
C,N,Z
RRNC
f
f = Rotate Right (No Carry) f
1
1
N,Z
RRNC
f,WREG
WREG = Rotate Right (No Carry) f
1
1
N,Z
RRNC
Ws,Wd
Wd = Rotate Right (No Carry) Ws
1
1
N,Z
SAC
Acc,#Slit4,Wdo(1)
Store Accumulator
1
1
None
SAC.R
Acc,#Slit4,Wdo(1)
Store Rounded Accumulator
1
1
None
69
SE
SE
Ws,Wnd
Wnd = sign-extended Ws
1
1
C,N,Z
70
SETM
SETM
f
f = 0xFFFF
1
1
None
SETM
WREG
WREG = 0xFFFF
1
1
None
71
Note
SFTAC
1:
SETM
Ws
Ws = 0xFFFF
1
1
None
SFTAC
Acc,Wn(1)
Arithmetic Shift Accumulator by (Wn)
1
1
OA,OB,OAB,
SA,SB,SAB
SFTAC
Acc,#Slit6(1)
Arithmetic Shift Accumulator by Slit6
1
1
OA,OB,OAB,
SA,SB,SAB
This instruction is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
DS70657E-page 390
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 28-2:
Base
Instr
#
Assembly
Mnemonic
72
SL
73
74
75
76
77
SUB
SUBB
SUBR
SUBBR
SWAP
INSTRUCTION SET OVERVIEW (CONTINUED)
Assembly Syntax
Description
# of
# of
Status Flags
Words Cycles
Affected
SL
f
f = Left Shift f
1
1
C,N,OV,Z
SL
f,WREG
WREG = Left Shift f
1
1
C,N,OV,Z
SL
Ws,Wd
Wd = Left Shift Ws
1
1
C,N,OV,Z
SL
Wb,Wns,Wnd
Wnd = Left Shift Wb by Wns
1
1
N,Z
SL
Wb,#lit5,Wnd
Wnd = Left Shift Wb by lit5
1
1
N,Z
SUB
Acc(1)
Subtract Accumulators
1
1
OA,OB,OAB,
SA,SB,SAB
SUB
f
f = f – WREG
1
1
C,DC,N,OV,Z
SUB
f,WREG
WREG = f – WREG
1
1
C,DC,N,OV,Z
SUB
#lit10,Wn
Wn = Wn – lit10
1
1
C,DC,N,OV,Z
SUB
Wb,Ws,Wd
Wd = Wb – Ws
1
1
C,DC,N,OV,Z
SUB
Wb,#lit5,Wd
Wd = Wb – lit5
1
1
C,DC,N,OV,Z
SUBB
f
f = f – WREG – (C)
1
1
C,DC,N,OV,Z
SUBB
f,WREG
WREG = f – WREG – (C)
1
1
C,DC,N,OV,Z
SUBB
#lit10,Wn
Wn = Wn – lit10 – (C)
1
1
C,DC,N,OV,Z
SUBB
Wb,Ws,Wd
Wd = Wb – Ws – (C)
1
1
C,DC,N,OV,Z
SUBB
Wb,#lit5,Wd
Wd = Wb – lit5 – (C)
1
1
C,DC,N,OV,Z
SUBR
f
f = WREG – f
1
1
C,DC,N,OV,Z
SUBR
f,WREG
WREG = WREG – f
1
1
C,DC,N,OV,Z
SUBR
Wb,Ws,Wd
Wd = Ws – Wb
1
1
C,DC,N,OV,Z
SUBR
Wb,#lit5,Wd
Wd = lit5 – Wb
1
1
C,DC,N,OV,Z
SUBBR
f
f = WREG – f – (C)
1
1
C,DC,N,OV,Z
SUBBR
f,WREG
WREG = WREG – f – (C)
1
1
C,DC,N,OV,Z
SUBBR
Wb,Ws,Wd
Wd = Ws – Wb – (C)
1
1
C,DC,N,OV,Z
SUBBR
Wb,#lit5,Wd
Wd = lit5 – Wb – (C)
1
1
C,DC,N,OV,Z
SWAP.b
Wn
Wn = nibble swap Wn
1
1
None
SWAP
Wn
Wn = byte swap Wn
1
1
None
78
TBLRDH
TBLRDH
Ws,Wd
Read Prog<23:16> to Wd<7:0>
1
5
None
79
TBLRDL
TBLRDL
Ws,Wd
Read Prog<15:0> to Wd
1
5
None
80
TBLWTH
TBLWTH
Ws,Wd
Write Ws<7:0> to Prog<23:16>
1
2
None
81
TBLWTL
TBLWTL
Ws,Wd
Write Ws to Prog<15:0>
1
2
None
82
ULNK
ULNK
Unlink Frame Pointer
1
1
SFA
83
XOR
XOR
f
f = f .XOR. WREG
1
1
N,Z
XOR
f,WREG
WREG = f .XOR. WREG
1
1
N,Z
XOR
#lit10,Wn
Wd = lit10 .XOR. Wd
1
1
N,Z
XOR
Wb,Ws,Wd
Wd = Wb .XOR. Ws
1
1
N,Z
XOR
Wb,#lit5,Wd
Wd = Wb .XOR. lit5
1
1
N,Z
ZE
Ws,Wnd
Wnd = Zero-extend Ws
1
1
C,Z,N
84
Note
ZE
1:
This instruction is available in dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X devices only.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 391
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 392
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
29.0
DEVELOPMENT SUPPORT
29.1
The PIC® microcontrollers and dsPIC® digital signal
controllers are supported with a full range of software
and hardware development tools:
• Integrated Development Environment
- MPLAB® IDE Software
• Compilers/Assemblers/Linkers
- MPLAB C Compiler for Various Device
Families
- HI-TECH C® for Various Device Families
- MPASMTM Assembler
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB Assembler/Linker/Librarian for
Various Device Families
• Simulators
- MPLAB SIM Software Simulator
• Emulators
- MPLAB REAL ICE™ In-Circuit Emulator
• In-Circuit Debuggers
- MPLAB ICD 3
- PICkit™ 3 Debug Express
• Device Programmers
- PICkit™ 2 Programmer
- MPLAB PM3 Device Programmer
• Low-Cost Demonstration/Development Boards,
Evaluation Kits, and Starter Kits
MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16/32-bit
microcontroller market. The MPLAB IDE is a Windows®
operating system-based application that contains:
• A single graphical interface to all debugging tools
- Simulator
- Programmer (sold separately)
- In-Circuit Emulator (sold separately)
- In-Circuit Debugger (sold separately)
• A full-featured editor with color-coded context
• A multiple project manager
• Customizable data windows with direct edit of
contents
• High-level source code debugging
• Mouse over variable inspection
• Drag and drop variables from source to watch
windows
• Extensive on-line help
• Integration of select third party tools, such as
IAR C Compilers
The MPLAB IDE allows you to:
• Edit your source files (either C or assembly)
• One-touch compile or assemble, and download to
emulator and simulator tools (automatically
updates all project information)
• Debug using:
- Source files (C or assembly)
- Mixed C and assembly
- Machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost-effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increased flexibility
and power.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 393
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
29.2
MPLAB C Compilers for Various
Device Families
The MPLAB C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC18,
PIC24 and PIC32 families of microcontrollers and the
dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration
capabilities, superior code optimization and ease of
use.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
29.3
HI-TECH C for Various Device
Families
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple
platforms.
MPASM Assembler
The MPASM Assembler is a full-featured, universal
macro assembler for PIC10/12/16/18 MCUs.
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code and COFF files for
debugging.
The MPASM Assembler features include:
MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler and the
MPLAB C18 C Compiler. It can link relocatable objects
from precompiled libraries, using directives from a
linker script.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
The HI-TECH C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC
family of microcontrollers and the dsPIC family of digital
signal controllers. These compilers provide powerful
integration capabilities, omniscient code generation
and ease of use.
29.4
29.5
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
29.6
MPLAB Assembler, Linker and
Librarian for Various Device
Families
MPLAB Assembler produces relocatable machine
code from symbolic assembly language for PIC24,
PIC32 and dsPIC devices. MPLAB C Compiler uses
the assembler to produce its object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
•
•
•
•
•
•
Support for the entire device instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
• Integration into MPLAB IDE projects
• User-defined macros to streamline
assembly code
• Conditional assembly for multi-purpose
source files
• Directives that allow complete control over the
assembly process
DS70657E-page 394
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
29.7
MPLAB SIM Software Simulator
29.9
The MPLAB SIM Software Simulator allows code
development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB SIM Software Simulator fully supports
symbolic debugging using the MPLAB C Compilers,
and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and
debug code outside of the hardware laboratory environment, making it an excellent, economical software
development tool.
29.8
MPLAB REAL ICE In-Circuit
Emulator System
MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC and MCU devices. It debugs and
programs PIC® Flash MCUs and dsPIC® Flash DSCs
with the easy-to-use, powerful graphical user interface of
the MPLAB Integrated Development Environment (IDE),
included with each kit.
The emulator is connected to the design engineer’s PC
using a high-speed USB 2.0 interface and is connected
to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal
(LVDS) interconnection (CAT5).
The emulator is field upgradable through future firmware
downloads in MPLAB IDE. In upcoming releases of
MPLAB IDE, new devices will be supported, and new
features will be added. MPLAB REAL ICE offers
significant advantages over competitive emulators
including low-cost, full-speed emulation, run-time
variable watches, trace analysis, complex breakpoints, a
ruggedized probe interface and long (up to three meters)
interconnection cables.
© 2011-2012 Microchip Technology Inc.
MPLAB ICD 3 In-Circuit Debugger
System
MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost effective high-speed hardware
debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU)
devices. It debugs and programs PIC® Flash microcontrollers and dsPIC® DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated
Development Environment (IDE).
The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a high-speed
USB 2.0 interface and is connected to the target with a
connector compatible with the MPLAB ICD 2 or MPLAB
REAL ICE systems (RJ-11). MPLAB ICD 3 supports all
MPLAB ICD 2 headers.
29.10 PICkit 3 In-Circuit Debugger/
Programmer and
PICkit 3 Debug Express
The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a
most affordable price point using the powerful graphical
user interface of the MPLAB Integrated Development
Environment (IDE). The MPLAB PICkit 3 is connected
to the design engineer's PC using a full speed USB
interface and can be connected to the target via an
Microchip debug (RJ-11) connector (compatible with
MPLAB ICD 3 and MPLAB REAL ICE). The connector
uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™.
The PICkit 3 Debug Express include the PICkit 3, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
Preliminary
DS70657E-page 395
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
29.11 PICkit 2 Development
Programmer/Debugger and
PICkit 2 Debug Express
29.13 Demonstration/Development
Boards, Evaluation Kits, and
Starter Kits
The PICkit™ 2 Development Programmer/Debugger is
a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash
families of microcontrollers. The full featured
Windows® programming interface supports baseline
(PIC10F,
PIC12F5xx,
PIC16F5xx),
midrange
(PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30,
dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit
microcontrollers, and many Microchip Serial EEPROM
products. With Microchip’s powerful MPLAB Integrated
Development Environment (IDE) the PICkit™ 2
enables in-circuit debugging on most PIC® microcontrollers. In-Circuit-Debugging runs, halts and single
steps the program while the PIC microcontroller is
embedded in the application. When halted at a breakpoint, the file registers can be examined and modified.
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for
adding custom circuitry and provide application firmware
and source code for examination and modification.
The PICkit 2 Debug Express include the PICkit 2, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
29.12 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages and a modular, detachable socket assembly to support various
package types. The ICSP™ cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices and incorporates an MMC card for file
storage and data applications.
DS70657E-page 396
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip
has a line of evaluation kits and demonstration software
for analog filter design, KEELOQ® security ICs, CAN,
IrDA®, PowerSmart battery management, SEEVAL®
evaluation system, Sigma-Delta ADC, flow rate
sensing, plus many more.
Also available are starter kits that contain everything
needed to experience the specified device. This usually
includes a single application and debug capability, all
on one board.
Check the Microchip web page (www.microchip.com)
for the complete list of demonstration, development
and evaluation kits.
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
30.0
ELECTRICAL CHARACTERISTICS
This section provides an overview of dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X electrical characteristics. Additional information will be provided in future revisions of this document as it
becomes available.
Absolute maximum ratings for the dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/MC20X
family are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability.
Functional operation of the device at these or any other conditions above the parameters indicated in the operation
listings of this specification is not implied.
Absolute Maximum Ratings(1)
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V
Voltage on any pin that is not 5V tolerant, with respect to VSS(3) ................................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS when VDD ≥ 3.0V(3) .................................................. -0.3V to +5.5V
Voltage on any 5V tolerant pin with respect to Vss when VDD < 3.0V(3) .................................................... -0.3V to 3.6V
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin(2) ...........................................................................................................................300 mA
Maximum current sunk/sourced by any 4x I/O pin ..................................................................................................15 mA
Maximum current sunk/sourced by any 8x I/O pin ..................................................................................................25 mA
Maximum current sunk by all ports(2,4) .................................................................................................................200 mA
Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only, and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods may affect device reliability.
2: Maximum allowable current is a function of device maximum power dissipation (see Table 30-2).
3: See the “Pin Diagrams” section for the 5V tolerant pins.
4: Exceptions are: dsPIC33EPXXXGP502, dsPIC33EPXXXMC202/502, and PIC24EPXXXGP/MC202
devices, which have a maximum sink/source capability of 130 mA.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 397
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
30.1
DC Characteristics
TABLE 30-1:
OPERATING MIPS VS. VOLTAGE
Maximum MIPS
Characteristic
VDD Range
(in Volts)
Temp Range
(in °C)
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and
PIC24EPXXXGP/MC20X
—
2.95V to 3.6V(1)
-40°C to +85°C
70
—
3.6V(1)
-40°C to +125°C
60
Note 1:
2.95V to
Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Op amp/Comparator, and
Comparator voltage reference will have degraded performance. Device functionality is tested but not
characterized. Refer to parameter BO10 in Table 30-12 for the minimum and maximum BOR values.
TABLE 30-2:
THERMAL OPERATING CONDITIONS
Rating
Symbol
Min.
Typ.
Max.
Unit
Operating Junction Temperature Range
TJ
-40
—
+125
°C
Operating Ambient Temperature Range
TA
-40
—
+85
°C
Operating Junction Temperature Range
TJ
-40
—
+140
°C
Operating Ambient Temperature Range
TA
-40
—
+125
°C
Industrial Temperature Devices
Extended Temperature Devices
Power Dissipation:
Internal chip power dissipation:
PINT = VDD x (IDD – Σ IOH)
PD
PINT + PI/O
W
PDMAX
(TJ – TA)/θJA
W
I/O Pin Power Dissipation:
I/O = Σ ({VDD – VOH} x IOH) + Σ (VOL x IOL)
Maximum Allowed Power Dissipation
TABLE 30-3:
THERMAL PACKAGING CHARACTERISTICS
Characteristic
Package Thermal Resistance, 64-Pin QFN
Package Thermal Resistance, 64-Pin TQFP 10x10 mm
Package Thermal Resistance, 44-Pin QFN
Package Thermal Resistance, 44-Pin TQFP 10x10 mm
Package Thermal Resistance, 44-Pin VTLA 6x6 mm
Package Thermal Resistance, 36-Pin VTLA 5x5 mm
Package Thermal Resistance, 28-Pin QFN-S
Package Thermal Resistance, 28-Pin SSOP
Package Thermal Resistance, 28-Pin SOIC
Package Thermal Resistance, 28-Pin SPDIP
Note 1:
Symbol
Typ.
Max.
Unit
Notes
θJA
θJA
θJA
θJA
θJA
θJA
θJA
θJA
θJA
θJA
28.0
—
°C/W
1
48.3
—
°C/W
1
29.0
—
°C/W
1
49.8
—
°C/W
1
25.2
—
°C/W
1
28.5
—
°C/W
1
30.0
—
°C/W
1
71.0
—
°C/W
1
69.7
—
°C/W
1
60.0
—
°C/W
1
Junction to ambient thermal resistance, Theta-JA (θ JA) numbers are achieved by package simulations.
DS70657E-page 398
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-4:
DC TEMPERATURE AND VOLTAGE SPECIFICATIONS
Standard Operating Conditions (see Note3): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ + 85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
3.0
—
3.6
V
—
Operating Voltage
DC10
VDD
Supply Voltage(3)
(2)
DC12
VDR
RAM Data Retention Voltage
1.8
—
—
V
—
DC16
VPOR
VDD Start Voltage
to ensure internal
Power-on Reset signal
—
—
VSS
V
—
DC17
SVDD
VDD Rise Rate
to ensure internal
Power-on Reset signal
0.03
—
—
Note 1:
2:
3:
V/ms 0V-1V in 100 ms
Data in “Typical” column is at 3.3V, 25°C unless otherwise stated.
This is the limit to which VDD may be lowered without losing RAM data.
Device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Op amp/Comparator, and
Comparator voltage reference will have degraded performance. Device functionality is tested but not
characterized. Refer to parameter BO10 in Table 30-12 for the minimum and maximum BOR values.
TABLE 30-5:
FILTER CAPACITOR (CEFC) SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated):
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Param
No.
Symbol
CEFC
Note 1:
Characteristics
External Filter Capacitor
Value(1)
Min.
Typ.
Max.
Units
Comments
4.7
10
—
μF
Capacitor must have a low
series resistance (< 1 ohm)
Typical VCAP voltage = 1.8 volts when VDD ≥ VDDMIN.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 399
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-6:
DC CHARACTERISTICS: OPERATING CURRENT (IDD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ + 85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typ.
Max.
Units
Conditions
Operating Current (IDD)
DC20d
9
15
mA
-40°C
DC20a
9
15
mA
+25°C
DC20b
9
15
mA
+85°C
DC20c
9
15
mA
+125°C
DC22d
16
25
mA
-40°C
DC22a
16
25
mA
+25°C
DC22b
16
25
mA
+85°C
DC22c
16
25
mA
+125°C
DC24d
27
35
mA
-40°C
DC24a
27
35
mA
+25°C
DC24b
27
35
mA
+85°C
DC24c
27
35
mA
+125°C
DC25d
36
55
mA
-40°C
DC25a
36
55
mA
+25°C
DC25b
36
55
mA
+85°C
DC25c
36
55
mA
+125°C
DC26d
41
60
mA
-40°C
DC26a
41
60
mA
+25°C
DC26b
41
60
mA
+85°C
Note 1:
3.3V
10 MIPS
3.3V
20 MIPS
3.3V
40 MIPS
3.3V
60 MIPS
3.3V
70 MIPS
IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDD measurements are as follows:
• Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from
rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• CPU, SRAM, program memory and data memory are operational
• No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are
zeroed)
• CPU executing while(1) statement
• JTAG disabled
DS70657E-page 400
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-7:
DC CHARACTERISTICS: IDLE CURRENT (IIDLE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ + 85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typ.
Max.
Units
Conditions
Idle Current (IIDLE)(1)
DC40d
3
5
mA
-40°C
DC40a
3
5
mA
+25°C
DC40b
3
5
mA
+85°C
DC40c
3
5
mA
+125°C
DC42d
6
10
mA
-40°C
DC42a
6
10
mA
+25°C
DC42b
6
10
mA
+85°C
DC42c
6
10
mA
+125°C
DC44d
11
18
mA
-40°C
DC44a
11
18
mA
+25°C
DC44b
11
18
mA
+85°C
DC44c
11
18
mA
+125°C
DC45d
17
27
mA
-40°C
DC45a
17
27
mA
+25°C
DC45b
17
27
mA
+85°C
DC45c
17
27
mA
+125°C
DC46d
20
35
mA
-40°C
DC46a
20
35
mA
+25°C
DC46b
20
35
mA
+85°C
Note 1:
3.3V
10 MIPS
3.3V
20 MIPS
3.3V
40 MIPS
3.3V
60 MIPS
3.3V
70 MIPS
Base Idle current (IIDLE) is measured as follows:
• CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are
zeroed)
• The NVMSIDL bit (NVMCON<12>) = 1 (i.e., Flash regulator is set to stand-by while the device is in
Idle mode)
• The VREGSF bit (RCON<11>) = 0 (i.e., Flash regulator is set to stand-by while the device is in Sleep
mode)
• JTAG disabled
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 401
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-8:
DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ + 85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typ.
Max.
Units
Conditions
Power-Down Current (IPD)(1) – dsPIC33EP32GP50X, dsPIC33EP32MC20X/50X, and PIC24EP32GP/MC20X
DC60d
30
—
μA
-40°C
DC60a
35
—
μA
+25°C
DC60b
150
—
μA
+85°C
DC60c
250
—
μA
+125°C
DC61d
8
—
μA
-40°C
DC61a
10
—
μA
+25°C
DC61b
12
—
μA
+85°C
DC61c
13
—
μA
+125°C
3.3V
Base Power-Down Current
3.3V
Watchdog Timer Current: ΔIWDT(2)
Power-Down Current (IPD)(1) – dsPIC33EP64GP50X, dsPIC33EP64MC20X/50X, and PIC24EP64GP/MC20X
DC60d
25
100
μA
-40°C
DC60a
30
100
μA
+25°C
DC60b
150
350
μA
+85°C
DC60c
350
800
μA
+125°C
DC61d
8
10
μA
-40°C
DC61a
10
15
μA
+25°C
DC61b
12
20
μA
+85°C
DC61c
13
25
μA
+125°C
Power-Down Current
DC60d
(IPD)(1) –
—
μA
-40°C
DC60a
35
—
μA
+25°C
150
—
μA
+85°C
DC60c
550
—
μA
+125°C
DC61d
8
—
μA
-40°C
DC61a
10
—
μA
+25°C
DC61b
12
—
μA
+85°C
13
—
μA
+125°C
DC61c
2:
Base Power-Down Current
3.3V
Watchdog Timer Current: ΔIWDT(2)
dsPIC33EP128GP50X, dsPIC33EP128MC20X/50X, and PIC24EP128GP/MC20X
30
DC60b
Note 1:
3.3V
3.3V
Base Power-Down Current
3.3V
Watchdog Timer Current: ΔIWDT(2)
IPD (Sleep) current is measured as follows:
• CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• All peripheral modules are disabled (PMDx bits are all ones)
• The VREGS bit (RCON<8>) = 0 (i.e., core regulator is set to stand-by while the device is in Sleep
mode)
• The VREGSF bit (RCON<11>) = 0 (i.e., Flash regulator is set to stand-by while the device is in Sleep
mode)
• JTAG disabled
The Δ current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
DS70657E-page 402
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-8:
DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ + 85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Parameter
No.
Typ.
Max.
Units
Conditions
Power-Down Current (IPD)(1,3) – dsPIC33EP256GP50X, dsPIC33EP256MC20X/50X, and PIC24EP256GP/MC20X
DC60d
35
—
μA
-40°C
DC60a
40
—
μA
+25°C
DC60b
250
—
μA
+85°C
DC60c
1000
—
μA
+125°C
DC61d
8
—
μA
-40°C
DC61a
10
—
μA
+25°C
DC61b
12
—
μA
+85°C
DC61c
13
—
μA
+125°C
3.3V
Base Power-Down Current
3.3V
Watchdog Timer Current: ΔIWDT(2)
Power-Down Current (IPD)(1,3) – dsPIC33EP512GP50X, dsPIC33EP512MC20X/50X, and PIC24EP512GP/MC20X
DC60d
40
—
μA
-40°C
DC60a
45
—
μA
+25°C
DC60b
350
—
μA
+85°C
DC60c
1500
—
μA
+125°C
DC61d
8
—
μA
-40°C
DC61a
10
—
μA
+25°C
DC61b
12
—
μA
+85°C
DC61c
13
—
μA
+125°C
Note 1:
2:
3.3V
Base Power-Down Current
3.3V
Watchdog Timer Current: ΔIWDT(2)
IPD (Sleep) current is measured as follows:
• CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• All peripheral modules are disabled (PMDx bits are all ones)
• The VREGS bit (RCON<8>) = 0 (i.e., core regulator is set to stand-by while the device is in Sleep
mode)
• The VREGSF bit (RCON<11>) = 0 (i.e., Flash regulator is set to stand-by while the device is in Sleep
mode)
• JTAG disabled
The Δ current is the additional current consumed when the module is enabled. This current should be
added to the base IPD current.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 403
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-9:
DC CHARACTERISTICS: DOZE CURRENT (IDOZE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤+ 85°C for Industrial
-40°C ≤ TA ≤+125°C for Extended
DC CHARACTERISTICS
Typ.
Max.
Doze
Ratio
Units
DC73a
35
53
1:2
mA
DC73g
20
30
1:128
mA
DC70a
35
53
1:2
mA
DC70g
20
30
1:128
mA
DC71a
35
53
1:2
mA
DC71g
20
30
1:128
mA
DC72a
28
42
1:2
mA
DC72g
15
30
1:128
mA
Parameter No.
Conditions
Doze Current (IDOZE)(1)
Note 1:
-40°C
3.3V
FOSC = 140 MHz
+25°C
3.3V
FOSC = 140 MHz
+85°C
3.3V
FOSC = 140 MHz
+125°C
3.3V
FOSC = 120 MHz
IDOZE is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDOZE measurements are as follows:
• Oscillator is configured in EC mode and external clock active, OSC1 is driven with external square
wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• CPU, SRAM, program memory and data memory are operational
• No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are
zeroed)
• CPU executing while(1) statement
• JTAG disabled
DS70657E-page 404
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-10: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
VIL
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
Input Low Voltage
DI10
Any I/O pin and MCLR
VSS
—
0.2 VDD
V
DI18
I/O Pins with SDAx, SCLx
VSS
—
0.3 VDD
V
SMBus disabled
I/O Pins with SDAx, SCLx
VSS
—
0.8
V
SMBus enabled
0.7 VDD
0.7 VDD
—
—
VDD
5.3
V
V
See Note 4
See Note 4
0.7 VDD
2.1
—
—
5.3
5.3
V
V
SMBus disabled
SMBus enabled
50
250
400
μA
VDD = 3.3V, VPIN = VSS
—
50
—
μA
VDD = 3.3V, VPIN = VDD
DI19
VIH
DI20
Input High Voltage
I/O Pins Not 5V Tolerant
I/O Pins 5V Tolerant and
MCLR
I/O Pins with SDAx, SCLx
I/O Pins with SDAx, SCLx
ICNPU
Change Notification Pull-up
Current
ICNPD
Change Notification Pulldown Current(5)
DI30
DI31
Note 1:
2:
3:
4:
5:
6:
7:
8:
9:
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current can be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
See “Pin Diagrams” for the 5V tolerant I/O pins.
VIL source < (VSS – 0.3). Characterized but not tested.
Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not
tested.
Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.
Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.
Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted
provided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not
exceed the specified limit. Characterized but not tested.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 405
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-10: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
Input Leakage Current(2,3)
IIL
DI50
I/O pins 5V Tolerant(4)
—
±1
—
μA
VSS ≤VPIN ≤VDD,
Pin at high-impedance
DI51
I/O Pins Not 5V Tolerant(4)
—
±1
—
μA
VSS ≤VPIN ≤VDD,
Pin at high-impedance,
-40°C ≤ TA ≤+85°C
DI51a
I/O Pins Not 5V Tolerant(4)
—
±1
—
μA
Analog pins shared
with external reference
pins,
-40°C ≤ TA ≤+85°C
DI51b
I/O Pins Not 5V Tolerant(4)
—
±1
—
μA
VSS ≤VPIN ≤VDD, Pin at
high-impedance,
-40°C ≤TA ≤+125°C
DI51c
I/O Pins Not 5V Tolerant(4)
—
±1
—
μA
Analog pins shared
with external reference
pins,
-40°C ≤TA ≤+125°C
DI55
MCLR
—
±1
—
μA
VSS ≤VPIN ≤VDD
DI56
OSC1
—
±1
—
μA
VSS ≤VPIN ≤VDD,
XT and HS modes
Note 1:
2:
3:
4:
5:
6:
7:
8:
9:
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current can be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
See “Pin Diagrams” for the 5V tolerant I/O pins.
VIL source < (VSS – 0.3). Characterized but not tested.
Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not
tested.
Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.
Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.
Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted
provided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not
exceed the specified limit. Characterized but not tested.
DS70657E-page 406
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-10: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
IICL
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
0
—
-5(5,8)
mA
All pins except VDD,
VSS, AVDD, AVSS,
MCLR, VCAP, and RB7
0
—
+5(6,7,8)
mA
All pins except VDD,
VSS, AVDD, AVSS,
MCLR, VCAP, RB7, and
all 5V tolerant pins(7)
-20(9)
—
+20(9)
mA
Input Low Injection Current
DI60a
IICH
Input High Injection Current
DI60b
∑IICT
DI60c
Total Input Injection Current
(sum of all I/O and control
pins)
Note 1:
2:
3:
4:
5:
6:
7:
8:
9:
Absolute instantaneous
sum of all ± input
injection currents from
all I/O pins
( | IICL + | IICH | ) ≤∑IICT
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current can be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
See “Pin Diagrams” for the 5V tolerant I/O pins.
VIL source < (VSS – 0.3). Characterized but not tested.
Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not
tested.
Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.
Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.
Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted
provided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not
exceed the specified limit. Characterized but not tested.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 407
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-11: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param. Symbol
DO10
VOL
Characteristic
Output Low Voltage
I/O Pins:
4x Sink Driver Pins - All I/O
output pins not defined as 8x
Sink Driver pins
Output Low Voltage
I/O Pins:
8x Sink Driver Pins - RA3(2),
RA4, RA9, RB7-RB15, RC3,
and RC15(3)
Min.
Typ.
Max.
Units
Conditions
—
—
0.4
V
IOL ≤10 mA, VDD = 3.3V
—
—
0.4
V
IOL ≤15 mA, VDD = 3.3V
—
V
IOH ≥ -10 mA, VDD = 3.3V
—
V
IOH ≥ -15 mA, VDD = 3.3V
Output High Voltage
I/O Pins:
2.4
—
4x Source Driver Pins - All I/O
output pins not defined as 8x
Source Driver pins
DO20 VOH
Output High Voltage
I/O Pins:
2.4
—
8x Source Driver Pins - RA3(2),
RA4, RA9, RB7-RB15, RC3,
and RC15(3)
Output High Voltage
—
1.5(1)
I/O Pins:
(1)
2.0
—
4x Source Driver Pins - All I/O
output pins not defined as 8x
3.0(1)
—
Sink Driver pins
DO20A VOH1
Output High Voltage
1.5(1)
—
I/O Pins:
2.0(1)
—
8x Source Driver Pins - RA3(2),
RA4, RA9, RB7-RB15, RC3,
3.0(1)
—
and RC15(3)
Note 1: Parameters are characterized, but not tested.
2: This driver pin applies only to devices with less than 64 pins.
3: This driver pin applies only to devices with 64 pins.
IOH ≥ -14 mA, VDD = 3.3V
—
—
V
IOH ≥ -12 mA, VDD = 3.3V
—
IOH ≥ -7 mA, VDD = 3.3V
—
IOH ≥ -22 mA, VDD = 3.3V
—
—
V
IOH ≥ -18 mA, VDD = 3.3V
IOH ≥ -10 mA, VDD = 3.3V
TABLE 30-12: ELECTRICAL CHARACTERISTICS: BOR
DC CHARACTERISTICS
Param
No.
BO10
Note 1:
2:
3:
Symbol
Standard Operating Conditions (see Note 3): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Characteristic
Min.(1)
Typ.
Max.
Units
Conditions
VDD
BOR Event on VDD transition
2.7
—
2.95
V
see
Note 2 and Note 3
high-to-low
Parameters are for design guidance only and are not tested in manufacturing.
The VBOR specification is relative to VDD.
The device is functional at VBORMIN < VDD < VDDMIN. Analog modules: ADC, Op amp/Comparator, and
Comparator voltage reference, will have degraded performance. Device functionality is tested but not
characterized.
VBOR
DS70657E-page 408
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-13: DC CHARACTERISTICS: PROGRAM MEMORY
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
Program Flash Memory
D130
EP
Cell Endurance
10,000
—
—
D131
VPR
VDD for Read
3.0
—
3.6
V
D132b
VPEW
VDD for Self-Timed Write
3.0
—
3.6
V
D134
TRETD
Characteristic Retention
20
—
—
Year Provided no other specifications
are violated, -40° C to +125° C
D135
IDDP
Supply Current during
Programming
—
10
—
mA
D136
IPEAK
Instantaneous Peak Current
During Start-up
—
—
150
mA
D137a
TPE
Page Erase Time
17.7
—
22.9
ms
TPE = 146893 FRC cycles,
TA = +85°C, See Note 2
D137b
TPE
Page Erase Time
17.5
—
23.1
ms
TPE = 146893 FRC cycles,
TA = +125°C, See Note 2
D138a
TWW
Word Write Cycle Time
41.7
—
53.8
µs
TWW = 346 FRC cycles,
TA = +85°C, See Note 2
D138b
TWW
Word Write Cycle Time
41.2
—
54.4
µs
TWW = 346 FRC cycles,
TA = +125°C, See Note 2
Note 1:
2:
E/W -40° C to +125° C
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
Other conditions: FRC = 7.37 MHz, TUN<5:0> = 'b011111 (for Minimum), TUN<5:0> = 'b100000 (for
Maximum). This parameter depends on the FRC accuracy (see Table 30-18) and the value of the FRC
Oscillator Tuning register (see Register 9-4). For complete details on calculating the Minimum and
Maximum time see Section 5.3 “Programming Operations”.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 409
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
30.2
AC Characteristics and Timing
Parameters
This
section
defines
dsPIC33EPXXXGP50X,
dsPIC33EPXXXMC20X/50X, and PIC24EPXXXGP/
MC20X AC characteristics and timing parameters.
TABLE 30-14: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Operating voltage VDD range as described in Section 30.1 “DC
Characteristics”.
AC CHARACTERISTICS
FIGURE 30-1:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1 – for all pins except OSC2
Load Condition 2 – for OSC2
VDD/2
CL
Pin
RL
VSS
CL
Pin
RL = 464Ω
CL = 50 pF for all pins except OSC2
15 pF for OSC2 output
VSS
TABLE 30-15: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS
Param
Symbol
No.
Characteristic
Min.
Typ.
Max.
Units
Conditions
DO50
COSCO
OSC2 pin
—
—
15
pF
In XT and HS modes when
external clock is used to drive
OSC1
DO56
CIO
All I/O pins and OSC2
—
—
50
pF
EC mode
DO58
CB
SCLx, SDAx
—
—
400
pF
In I2C™ mode
DS70657E-page 410
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-2:
EXTERNAL CLOCK TIMING
Q1
Q2
Q3
Q4
Q1
Q2
OS30
OS30
Q3
Q4
OSC1
OS20
OS25
OS31
OS31
CLKO
OS41
OS40
TABLE 30-16: EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
OS10
Symb
FIN
OS20
TOSC
OS25
TCY
Min.
Typ.(1)
Max.
Units
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
DC
—
60
MHz
EC
Oscillator Crystal Frequency
3.5
10
—
—
10
25
MHz
MHz
XT
HS
TOSC = 1/FOSC
8.33
—
DC
ns
+125ºC
TOSC = 1/FOSC
7.14
—
DC
ns
+85ºC
Time(2)
16.67
—
DC
ns
+125ºC
Instruction Cycle Time(2)
14.28
—
DC
ns
+85ºC
Characteristic
Instruction Cycle
Conditions
OS30
TosL,
TosH
External Clock in (OSC1)
High or Low Time
0.375 x TOSC
—
0.625 x TOSC
ns
EC
OS31
TosR,
TosF
External Clock in (OSC1)
Rise or Fall Time
—
—
20
ns
EC
OS40
TckR
CLKO Rise Time(3)
—
5.2
—
ns
—
5.2
—
ns
—
12
—
mA/V
HS, VDD = 3.3V
TA = +25ºC
6
—
mA/V
XT, VDD = 3.3V
TA = +25ºC
Time(3)
OS41
TckF
CLKO Fall
OS42
GM
External Oscillator
Transconductance(4)
—
Note 1:
2:
3:
4:
—
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at
“Minimum” values with an external clock applied to the OSC1 pin. When an external clock input is used,
the “Maximum” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.
This parameter is characterized, but not tested in manufacturing.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 411
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-17: PLL CLOCK TIMING SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
OS50
FPLLI
PLL Voltage Controlled
Oscillator (VCO) Input
Frequency Range
0.8
—
8.0
MHz
OS51
FSYS
On-Chip VCO System
Frequency
120
—
340
MHz
OS52
TLOCK
PLL Start-up Time (Lock Time)
0.9
1.5
3.1
ms
—
OS53
DCLK
CLKO Stability (Jitter)(2)
-3
0.5
3
%
—
Note 1:
ECPLL, XTPLL modes
—
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
This jitter specification is based on clock cycle-by-clock cycle measurements. To get the effective jitter for
individual time bases or communication clocks used by the application, use the following formula:
2:
D CLK
Effective Jitter = ------------------------------------------------------------------------------------------F OSC
-------------------------------------------------------------------------------------Time Base or Communication Clock
For example, if FOSC = 120 MHz and the SPI bit rate = 10 MHz, the effective jitter is as follows:
D CLK
CLK
CLK
------------- = D
------------- = ------------Effective Jitter = D
3.464
120
12
--------10
TABLE 30-18: INTERNAL FRC ACCURACY
AC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Min.
Typ.
Max.
Units
Conditions
Internal FRC Accuracy @ FRC Frequency = 7.37 MHz(1)
F20a
FRC
-0.9
0.5
+0.9
%
-40°C ≤TA ≤+85°C
VDD = 3.0-3.6V
F20b
FRC
-2
1
+2
%
-40°C ≤ TA ≤ +125°C
VDD = 3.0-3.6V
Note 1:
Frequency calibrated at 25°C and 3.3V. TUN bits can be used to compensate for temperature drift.
TABLE 30-19: INTERNAL LPRC ACCURACY
AC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Min.
Typ.
Max.
Units
-15
5
+15
%
Conditions
LPRC @ 32.768 kHz(1)
F21a
F21b
Note 1:
LPRC
LPRC
-30
10
+30
%
-40°C ≤ TA ≤ +85°C
-40°C
≤ TA
≤ +125°C
VDD = 3.0-3.6V
VDD = 3.0-3.6V
Change of LPRC frequency as VDD changes.
DS70657E-page 412
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-3:
I/O TIMING CHARACTERISTICS
I/O Pin
(Input)
DI35
DI40
I/O Pin
(Output)
New Value
Old Value
DO31
DO32
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-20: I/O TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Typ.(1)
Max.
Units
Conditions
—
5
10
ns
—
DO31
TIOR
DO32
TIOF
Port Output Fall Time
—
5
10
ns
—
DI35
TINP
INTx Pin High or Low Time (input)
20
—
—
ns
—
TRBP
CNx High or Low Time (input)
2
—
—
TCY
—
DI40
Note 1:
Port Output Rise Time
Min.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
FIGURE 30-4:
BOR AND MASTER CLEAR RESET TIMING CHARACTERISTICS
MCLR
TMCLR
(SY20)
BOR
TBOR
(SY30)
Various delays (depending on configuration)
Reset Sequence
CPU starts fetching code
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 413
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-21: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
TIMING REQUIREMENTS
AC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Param
No.
Min.
Typ.(2)
Symbol
Characteristic(1)
Max. Units
Conditions
—
SY00
TPU
Power-up Period
—
400
600
μs
SY10
TOST
Oscillator Start-up Time
—
1024 TOSC
—
—
TOSC = OSC1 period
SY12
TWDT
Watchdog Timer
Time-out Period
0.85
—
1.15
ms
WDTPRE = 0, WDTPOST = 0000,
using LPRC tolerances indicated
in F21 (see Table 30-19) at 85ºC
3.4
—
4.6
ms
WDTPRE = 1, WDTPOST = 0000,
using LPRC tolerances indicated
in F21 (see Table 30-19) at 85ºC
0.68
0.72
1.2
μs
—
SY13
TIOZ
I/O High-Impedance
from MCLR Low or
Watchdog Timer Reset
SY20
TMCLR
MCLR Pulse Width (low)
2
—
—
μs
—
—
SY30
TBOR
BOR Pulse Width (low)
1
—
—
μs
SY35
TFSCM
Fail-Safe Clock Monitor
Delay
—
500
900
μs
SY36
TVREG
Voltage regulator
standby-to-active mode
transition time
—
—
30
µs
—
SY37
TOSCDFRC
FRC Oscillator start-up
delay
46
48
54
µs
—
SY38
TOSCDLPRC LPRC Oscillator start-up
delay
—
—
70
µs
—
Note 1:
2:
-40°C to +85°C
These parameters are characterized but not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
DS70657E-page 414
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-5:
TIMER1-TIMER5 EXTERNAL CLOCK TIMING CHARACTERISTICS
TxCK
Tx11
Tx10
Tx15
OS60
Tx20
TMRx
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-22: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(2)
Min.
Typ.
Max.
Units
Conditions
Greater of:
20 or
(TCY + 20)/N
—
—
ns
Must also meet
parameter TA15
N = prescaler
value (1, 8, 64,
256)
TA10
TTXH
TxCK High
Time
Synchronous
mode
Asynchronous
35
—
—
ns
—
TA11
TTXL
TxCK Low
Time
Synchronous
mode
Greater of:
20 or
(TCY + 20)/N
—
—
ns
Must also meet
parameter TA15
N = prescaler
value (1, 8, 64,
256)
Asynchronous
10
—
—
ns
TA15
TTXP
TxCK Input
Period
Synchronous
mode
Greater of:
40 or
(2 TCY + 40)/N
—
—
ns
OS60
Ft1
T1CK Oscillator Input
frequency Range (oscillator
enabled by setting bit TCS
(T1CON<1>))
DC
—
50
kHz
—
TA20
TCKEXTMRL Delay from External TxCK
Clock Edge to Timer
Increment
0.75 TCY + 40
—
1.75 TCY + 40
ns
—
Note 1:
2:
—
N = prescale
value
(1, 8, 64, 256)
Timer1 is a Type A.
These parameters are characterized, but are not tested in manufacturing.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 415
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-23: TIMER2 AND TIMER4 (TYPE B TIMER) EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min.
Typ.
Max.
Units
Conditions
TB10
TtxH
TxCK High Synchronous
mode
Time
Greater of:
20 or
(TCY + 20)/N
—
—
ns
Must also meet
parameter TB15
N = prescale
value
(1, 8, 64, 256)
TB11
TtxL
TxCK Low Synchronous
Time
mode
Greater of:
20 or
(TCY + 20)/N
—
—
ns
Must also meet
parameter TB15
N = prescale
value
(1, 8, 64, 256)
TB15
TtxP
TxCK
Input
Period
Synchronous
mode
Greater of:
40 or
(2 TCY + 40)/N
—
—
ns
N = prescale
value
(1, 8, 64, 256)
TB20
TCKEXTMRL Delay from External TxCK
Clock Edge to Timer
Increment
0.75 TCY + 40
—
1.75 TCY + 40
ns
Note 1:
—
These parameters are characterized, but are not tested in manufacturing.
TABLE 30-24: TIMER3 AND TIMER5 (TYPE C TIMER) EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min.
Typ.
Max.
Units
Conditions
TC10
TtxH
TxCK High
Time
Synchronous
TCY + 20
—
—
ns
Must also meet
parameter TC15
TC11
TtxL
TxCK Low
Time
Synchronous
TCY + 20
—
—
ns
Must also meet
parameter TC15
TC15
TtxP
TxCK Input
Period
Synchronous,
with prescaler
2 TCY + 40
—
—
ns
N = prescale
value
(1, 8, 64, 256)
TC20
TCKEXTMRL Delay from External TxCK
Clock Edge to Timer Increment
0.75 TCY + 40
—
1.75 TCY + 40
ns
Note 1:
—
These parameters are characterized, but are not tested in manufacturing.
DS70657E-page 416
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-6:
INPUT CAPTURE (ICx) TIMING CHARACTERISTICS
ICx
IC10
IC11
IC15
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-25: INPUT CAPTURE MODULE TIMING REQUIREMENTS
AC CHARACTERISTICS
Param.
Symbol
No.
IC10
IC11
IC15
Note 1:
TCCL
TCCH
TCCP
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Characteristics(1)
ICx Input Low Time
ICx Input High Time
Min.
Max.
Greater of
12.5 + 25
or
(0.5 TCY/N) + 25
Units
—
Greater of
12.5 + 25
or
(0.5 TCY/N) + 25
—
ns
Must also
meet
parameter
IC15.
ns
Must also
meet
parameter
IC15.
Greater of
25 + 50
—
ns
or
(1 TCY/N) + 50
These parameters are characterized, but not tested in manufacturing.
FIGURE 30-7:
Conditions
N = prescale
value (1, 4, 16)
ICx Input Period
—
OUTPUT COMPARE MODULE (OCx) TIMING CHARACTERISTICS
OCx
(Output Compare
or PWM Mode)
OC10
OC11
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-26: OUTPUT COMPARE MODULE TIMING REQUIREMENTS
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Min.
Typ.
Max.
Units
Conditions
OC10
TccF
OCx Output Fall Time
—
—
—
ns
See parameter DO32
OC11
TccR
OCx Output Rise Time
—
—
—
ns
See parameter DO31
Note 1:
These parameters are characterized but not tested in manufacturing.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 417
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-8:
OC/PWM MODULE TIMING CHARACTERISTICS
OC20
OCFA
OC15
OCx
TABLE 30-27: OC/PWM MODE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min.
Typ.
Max.
Units
Conditions
OC15
TFD
Fault Input to PWM I/O
Change
—
—
TCY + 20
ns
—
OC20
TFLT
Fault Input Pulse Width
TCY + 20
—
—
ns
—
Note 1:
These parameters are characterized but not tested in manufacturing.
DS70657E-page 418
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-9:
HIGH-SPEED PWM MODULE FAULT TIMING CHARACTERISTICS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
MP30
Fault Input
(active-low)
MP20
PWMx
FIGURE 30-10:
HIGH-SPEED PWM MODULE TIMING CHARACTERISTICS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
MP11 MP10
PWMx
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-28: HIGH-SPEED PWM MODULE TIMING REQUIREMENTS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Min.
Typ.
Max.
Units
Conditions
MP10
TFPWM
PWM Output Fall Time
—
—
—
ns
See parameter DO32
MP11
TRPWM
PWM Output Rise Time
—
—
—
ns
See parameter DO31
TFD
Fault Input ↓ to PWM
I/O Change
—
—
15
ns
—
TFH
Fault Input Pulse Width
15
—
—
ns
—
MP20
MP30
Note 1:
These parameters are characterized but not tested in manufacturing.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 419
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-11:
TIMERQ (QEI MODULE) EXTERNAL CLOCK TIMING CHARACTERISTICS
(dsPIC33EPXXXMC20X/50X AND PIC24EPXXXMC20X DEVICES ONLY)
QEB
TQ11
TQ10
TQ15
TQ20
POSCNT
TABLE 30-29: QEI MODULE EXTERNAL CLOCK TIMING REQUIREMENTS
(dsPIC33EPXXXMC20X/50X AND PIC24EPXXXMC20X DEVICES ONLY)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
TQ10
TQ11
TQ15
TQ20
Note 1:
Symbol
TtQH
TtQL
TtQP
Characteristic(1)
Min.
Typ.
Max.
Units
Conditions
TQCK High
Time
Synchronous, Greater of 12.5 + 25
or
with prescaler
(0.5 TCY/N) + 25
—
—
ns
Must also meet
parameter TQ15.
TQCK Low
Time
Synchronous, Greater of 12.5 + 25
with prescaler
or
(0.5 TCY/N) + 25
—
—
ns
Must also meet
parameter TQ15.
TQCP Input
Period
Synchronous,
with prescaler
Greater of 25 + 50
or
(1 TCY/N) + 50
—
—
ns
—
—
1
TCY
—
—
TCKEXTMRL Delay from External TxCK
Clock Edge to Timer Increment
These parameters are characterized but not tested in manufacturing.
DS70657E-page 420
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-12:
QEA/QEB INPUT CHARACTERISTICS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
TQ36
QEA
(input)
TQ30
TQ31
TQ35
QEB
(input)
TQ41
TQ40
TQ30
TQ31
TQ35
QEB
Internal
TABLE 30-30: QUADRATURE DECODER TIMING REQUIREMENTS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
Max.
Units
Conditions
6 TCY
—
ns
—
TQ30
TQUL
TQ31
TQUH
Quadrature Input High Time
6 TCY
—
ns
—
TQ35
TQUIN
Quadrature Input Period
12 TCY
—
ns
—
TQ36
TQUP
Quadrature Phase Period
3 TCY
—
ns
—
TQ40
TQUFL
Filter Time to Recognize Low,
with Digital Filter
3 * N * TCY
—
ns
N = 1, 2, 4, 16, 32, 64,
128 and 256 (Note 3)
TQ41
TQUFH
Filter Time to Recognize High,
with Digital Filter
3 * N * TCY
—
ns
N = 1, 2, 4, 16, 32, 64,
128 and 256 (Note 3)
Note 1:
2:
These parameters are characterized but not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
N = Index Channel Digital Filter Clock Divide Select bits. Refer to Section 15. “Quadrature Encoder
Interface (QEI)” (DS70601) in the “dsPIC33E/PIC24E Family Reference Manual”. Please see the
Microchip web site for the latest family reference manual sections.
3:
Quadrature Input Low Time
Typ.(2)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 421
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-13:
QEI MODULE INDEX PULSE TIMING CHARACTERISTICS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
QEA
(input)
QEB
(input)
Ungated
Index
TQ50
TQ51
Index Internal
TQ55
Position Counter Reset
TABLE 30-31: QEI INDEX PULSE TIMING REQUIREMENTS
(dsPIC33EPXXXMC20X/50X and PIC24EPXXXMC20X DEVICES ONLY)
AC CHARACTERISTICS
Param
No.
Symbol
TQ50
TqIL
TQ51
TQ55
Note 1:
2:
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
Characteristic(1)
Min.
Max.
Units
Conditions
Filter Time to Recognize Low,
with Digital Filter
3 * N * TCY
—
ns
N = 1, 2, 4, 16, 32, 64,
128 and 256 (Note 2)
TqiH
Filter Time to Recognize High,
with Digital Filter
3 * N * TCY
—
ns
N = 1, 2, 4, 16, 32, 64,
128 and 256 (Note 2)
Tqidxr
Index Pulse Recognized to Position
Counter Reset (ungated index)
3 TCY
—
ns
—
These parameters are characterized but not tested in manufacturing.
Alignment of index pulses to QEA and QEB is shown for position counter Reset timing only. Shown for
forward direction only (QEA leads QEB). Same timing applies for reverse direction (QEA lags QEB) but
index pulse recognition occurs on falling edge.
DS70657E-page 422
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-32: SPI2 MAXIMUM DATA/CLOCK RATE SUMMARY
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Maximum
Data Rate
Master
Transmit Only
(Half-Duplex)
15 MHz
Table 30-32
9 MHz
—
Master
Transmit/Receive
(Full-Duplex)
Slave
Transmit/Receive
(Full-Duplex)
CKE
—
—
Table 30-33
—
CKP
SMP
0,1
0,1
0,1
1
0,1
1
9 MHz
—
Table 30-34
—
0
0,1
1
15 MHz
—
—
Table 30-35
1
0
0
11 MHz
—
—
Table 30-36
1
1
0
15 MHz
—
—
Table 30-37
0
1
0
11 MHz
—
—
Table 30-38
0
0
0
FIGURE 30-14:
SPI2 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 0) TIMING
CHARACTERISTICS
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
MSb
SDOx
Bit 14 - - - - - -1
SP30, SP31
LSb
SP30, SP31
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 423
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-15:
SPI2 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 1) TIMING
CHARACTERISTICS
SP36
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
SDOx
LSb
SP30, SP31
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-33: SPI2 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
See Note 3
SP10
TscP
Maximum SCK Frequency
—
—
15
MHz
SP20
TscF
SCKx Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
6
20
ns
—
SP36
TdiV2scH,
TdiV2scL
SDOx Data Output Setup to
First SCKx Edge
30
—
—
ns
—
Note 1:
2:
3:
4:
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 424
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-16:
SPI2 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = X, SMP = 1) TIMING
CHARACTERISTICS
SP36
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
SDOx
SP30, SP31
SP40
SDIx
LSb
MSb In
LSb In
Bit 14 - - - -1
SP41
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-34: SPI2 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
See Note 3
SP10
SP20
TscP
TscF
Maximum SCK Frequency
SCKx Output Fall Time
—
—
—
—
9
—
MHz
ns
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
SP35
TscH2doV, SDOx Data Output Valid after
—
6
20
ns
TscL2doV SCKx Edge
TdoV2sc, SDOx Data Output Setup to
30
—
—
ns
—
TdoV2scL First SCKx Edge
TdiV2scH, Setup Time of SDIx Data
30
—
—
ns
—
TdiV2scL Input to SCKx Edge
TscH2diL, Hold Time of SDIx Data Input
30
—
—
ns
—
TscL2diL
to SCKx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this
specification.
Assumes 50 pF load on all SPIx pins.
SP36
SP40
SP41
Note 1:
2:
3:
4:
© 2011-2012 Microchip Technology Inc.
Preliminary
See parameter DO32
and Note 4
See parameter DO31
and Note 4
See parameter DO32
and Note 4
See parameter DO31
and Note 4
—
DS70657E-page 425
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-17:
SPI2 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = X, SMP = 1) TIMING
CHARACTERISTICS
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35 SP36
Bit 14 - - - - - -1
MSb
SDOx
SP30, SP31
SDIx
LSb
SP30, SP31
MSb In
LSb In
Bit 14 - - - -1
SP40 SP41
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-35: SPI2 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
-40ºC to +125ºC and
see Note 3
See parameter DO32
and Note 4
See parameter DO31
and Note 4
See parameter DO32
and Note 4
See parameter DO31
and Note 4
—
SP10
TscP
Maximum SCK Frequency
—
—
9
MHz
SP20
TscF
SCKx Output Fall Time
—
—
—
ns
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
SP35
TscH2doV, SDOx Data Output Valid after
—
6
20
ns
TscL2doV SCKx Edge
TdoV2scH, SDOx Data Output Setup to
30
—
—
ns
—
TdoV2scL First SCKx Edge
TdiV2scH, Setup Time of SDIx Data
30
—
—
ns
—
TdiV2scL Input to SCKx Edge
TscH2diL, Hold Time of SDIx Data Input
30
—
—
ns
—
TscL2diL
to SCKx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this
specification.
Assumes 50 pF load on all SPIx pins.
SP36
SP40
SP41
Note 1:
2:
3:
4:
DS70657E-page 426
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-18:
SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING
CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP70
SP73
SCKx
(CKP = 1)
SP72
SP36
SP35
SP72
MSb
SDOx
Bit 14 - - - - - -1
LSb
SP30,SP31
SDIx
SDI
MSb In
SP73
SP51
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 427
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-36: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
MHz
Conditions
SP70
TscP
Maximum SCK Input Frequency
—
—
SP72
TscF
SCKx Input Fall Time
—
—
Lesser
of FP
or 15
—
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
SP35
TscH2doV,
TscL2doV
TdoV2scH,
TdoV2scL
TdiV2scH,
TdiV2scL
TscH2diL,
TscL2diL
SDOx Data Output Valid after
SCKx Edge
SDOx Data Output Setup to
First SCKx Edge
Setup Time of SDIx Data Input
to SCKx Edge
—
6
20
ns
See parameter DO32
and Note 4
See parameter DO31
and Note 4
See parameter DO32
and Note 4
See parameter DO31
and Note 4
—
30
—
—
ns
—
30
—
—
ns
—
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH
TscL2ssH
TssL2doV
SSx ↑ after SCKx Edge
1.5 TCY + 40
—
—
ns
See Note 4
SP36
SP40
SP41
SP60
Note 1:
2:
3:
4:
ns
See Note 3
SDOx Data Output Valid after
—
—
50
ns
—
SSx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must
not violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 428
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-19:
SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING
CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP70
SP73
SCKx
(CKP = 1)
SP72
SP36
SP35
SP72
MSb
SDOx
Bit 14 - - - - - -1
LSb
SP30,SP31
SDI
SDIx
MSb In
SP73
SP51
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 429
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-37: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
See Note 3
SP70
TscP
Maximum SCK Input Frequency
—
—
Lesser
of FP
or 11
MHz
SP72
TscF
SCKx Input Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH
TscL2ssH
SSx ↑ after SCKx Edge
1.5 TCY + 40
—
—
ns
See Note 4
SP60
TssL2doV
SDOx Data Output Valid after
SSx Edge
—
—
50
ns
—
Note 1:
2:
3:
4:
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 430
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-20:
SPI2 SLAVE MODE (FULL-DUPLEX CKE = 0, CKP = 1, SMP = 0) TIMING
CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP70
SP73
SP72
SP72
SP73
SCKX
(CKP = 1)
SP35 SP36
MSb
SDOX
Bit 14 - - - - - -1
LSb
SP51
SP30,SP31
SDIX
MSb In
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 431
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-38: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
SP70
TscP
Maximum SCK Input Frequency
—
—
15
MHz
SP72
TscF
SCKx Input Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH
TscL2ssH
SSx ↑ after SCKx Edge
1.5 TCY + 40
—
—
ns
See Note 4
Note 1:
2:
3:
4:
See Note 3
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must
not violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 432
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-21:
SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING
CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP70
SP73
SP72
SP72
SP73
SCKX
(CKP = 1)
SP35 SP36
MSb
SDOX
Bit 14 - - - - - -1
LSb
SP51
SP30,SP31
SDIX
MSb In
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 433
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-39: SPI2 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
SP70
TscP
Maximum SCK Input Frequency
—
—
11
MHz
SP72
TscF
SCKx Input Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH
TscL2ssH
SSx ↑ after SCKx Edge
1.5 TCY + 40
—
—
ns
See Note 4
Note 1:
2:
3:
4:
See Note 3
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 434
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-40: SPI1 MAXIMUM DATA/CLOCK RATE SUMMARY
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Maximum
Data Rate
Master
Transmit Only
(Half-Duplex)
Master
Transmit/Receive
(Full-Duplex)
Slave
Transmit/Receive
(Full-Duplex)
CKE
CKP
SMP
15 MHz
Table 30-41
—
—
0,1
0,1
0,1
10 MHz
—
Table 30-42
—
1
0,1
1
10 MHz
—
Table 30-43
—
0
0,1
1
15 MHz
—
—
Table 30-44
1
0
0
11 MHz
—
—
Table 30-45
1
1
0
15 MHz
—
—
Table 30-46
0
1
0
11 MHz
—
—
Table 30-47
0
0
0
FIGURE 30-22:
SPI1 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 0) TIMING
CHARACTERISTICS
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
MSb
SDOx
Bit 14 - - - - - -1
SP30, SP31
LSb
SP30, SP31
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 435
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-23:
SPI1 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 1) TIMING
CHARACTERISTICS
SP36
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
SDOx
LSb
SP30, SP31
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-41: SPI1 MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
See Note 3
SP10
TscP
Maximum SCK Frequency
—
—
15
MHz
SP20
TscF
SCKx Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
6
20
ns
—
SP36
TdiV2scH,
TdiV2scL
SDOx Data Output Setup to
First SCKx Edge
30
—
—
ns
—
Note 1:
2:
3:
4:
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 436
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-24:
SPI1 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = X, SMP = 1) TIMING
CHARACTERISTICS
SP36
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
SDOx
SP30, SP31
SP40
SDIx
LSb
MSb In
LSb In
Bit 14 - - - -1
SP41
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-42: SPI1 MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
See Note 3
SP10
SP20
TscP
TscF
Maximum SCK Frequency
SCKx Output Fall Time
—
—
—
—
10
—
MHz
ns
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
SP35
TscH2doV, SDOx Data Output Valid after
—
6
20
ns
TscL2doV SCKx Edge
TdoV2sc, SDOx Data Output Setup to
30
—
—
ns
—
TdoV2scL First SCKx Edge
TdiV2scH, Setup Time of SDIx Data
30
—
—
ns
—
TdiV2scL Input to SCKx Edge
TscH2diL, Hold Time of SDIx Data Input
30
—
—
ns
—
TscL2diL
to SCKx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this
specification.
Assumes 50 pF load on all SPIx pins.
SP36
SP40
SP41
Note 1:
2:
3:
4:
© 2011-2012 Microchip Technology Inc.
Preliminary
See parameter DO32
and Note 4
See parameter DO31
and Note 4
See parameter DO32
and Note 4
See parameter DO31
and Note 4
—
DS70657E-page 437
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-25:
SPI1 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = X, SMP = 1) TIMING
CHARACTERISTICS
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35 SP36
Bit 14 - - - - - -1
MSb
SDOx
SP30, SP31
SDIx
LSb
SP30, SP31
MSb In
LSb In
Bit 14 - - - -1
SP40 SP41
Note: Refer to Figure 30-1 for load conditions.
TABLE 30-43: SPI1 MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
SP10
TscP
Maximum SCK Frequency
—
—
10
MHz
SP20
TscF
SCKx Output Fall Time
—
—
—
ns
SP21
TscR
SCKx Output Rise Time
—
—
—
ns
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
SP35
-40ºC to +125ºC and
see Note 3
See parameter DO32
and Note 4
See parameter DO31
and Note 4
See parameter DO32
and Note 4
See parameter DO31
and Note 4
—
TscH2doV, SDOx Data Output Valid after
—
6
20
ns
TscL2doV SCKx Edge
TdoV2scH, SDOx Data Output Setup to
30
—
—
ns
—
TdoV2scL First SCKx Edge
TdiV2scH, Setup Time of SDIx Data
30
—
—
ns
—
TdiV2scL Input to SCKx Edge
TscH2diL, Hold Time of SDIx Data Input
30
—
—
ns
—
TscL2diL
to SCKx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 100 ns. The clock generated in Master mode must not violate this
specification.
Assumes 50 pF load on all SPIx pins.
Param.
SP36
SP40
SP41
Note 1:
2:
3:
4:
Symbol
DS70657E-page 438
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-26:
SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING
CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP70
SP73
SCKx
(CKP = 1)
SP72
SP36
SP35
SP72
MSb
SDOx
Bit 14 - - - - - -1
LSb
SP30,SP31
SDI
SDIx
MSb In
SP73
SP51
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 439
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-44: SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
MHz
Conditions
SP70
TscP
Maximum SCK Input Frequency
—
—
SP72
TscF
SCKx Input Fall Time
—
—
Lesser
of FP
or 15
—
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
SP35
TscH2doV,
TscL2doV
TdoV2scH,
TdoV2scL
TdiV2scH,
TdiV2scL
TscH2diL,
TscL2diL
SDOx Data Output Valid after
SCKx Edge
SDOx Data Output Setup to
First SCKx Edge
Setup Time of SDIx Data Input
to SCKx Edge
—
6
20
ns
See parameter DO32
and Note 4
See parameter DO31
and Note 4
See parameter DO32
and Note 4
See parameter DO31
and Note 4
—
30
—
—
ns
—
30
—
—
ns
—
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH
TscL2ssH
TssL2doV
SSx ↑ after SCKx Edge
1.5 TCY + 40
—
—
ns
See Note 4
SP36
SP40
SP41
SP60
Note 1:
2:
3:
4:
ns
See Note 3
SDOx Data Output Valid after
—
—
50
ns
—
SSx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must
not violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 440
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-27:
SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING
CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP70
SP73
SCKx
(CKP = 1)
SP72
SP36
SP35
SP72
MSb
SDOx
Bit 14 - - - - - -1
LSb
SP30,SP31
SDI
SDIx
MSb In
SP73
SP51
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 441
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-45: SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
See Note 3
SP70
TscP
Maximum SCK Input Frequency
—
—
Lesser
of FP
or 11
MHz
SP72
TscF
SCKx Input Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH, SSx ↑ after SCKx Edge
TscL2ssH
1.5 TCY + 40
—
—
ns
See Note 4
SP60
TssL2doV
—
—
50
ns
—
Note 1:
2:
3:
4:
SDOx Data Output Valid after
SSx Edge
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 442
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-28:
SPI1 SLAVE MODE (FULL-DUPLEX CKE = 0, CKP = 1, SMP = 0) TIMING
CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP70
SP73
SP72
SP72
SP73
SCKX
(CKP = 1)
SP35 SP36
MSb
SDOX
Bit 14 - - - - - -1
LSb
SP51
SP30,SP31
SDIX
MSb In
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 443
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-46: SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
SP70
TscP
Maximum SCK Input Frequency
—
—
15
MHz
SP72
TscF
SCKx Input Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH, SSx ↑ after SCKx Edge
TscL2ssH
1.5 TCY + 40
—
—
ns
See Note 4
Note 1:
2:
3:
4:
See Note 3
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must
not violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 444
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-29:
SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING
CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP70
SP73
SP72
SP72
SP73
SCKX
(CKP = 1)
SP35 SP36
MSb
SDOX
Bit 14 - - - - - -1
LSb
SP51
SP30,SP31
SDIX
MSb In
Bit 14 - - - -1
LSb In
SP41
SP40
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 445
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-47: SPI1 SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic(1)
Min.
Typ.(2)
Max.
Units
Conditions
SP70
TscP
Maximum SCK Input Frequency
—
—
11
MHz
SP72
TscF
SCKx Input Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP73
TscR
SCKx Input Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP30
TdoF
SDOx Data Output Fall Time
—
—
—
ns
See parameter DO32
and Note 4
SP31
TdoR
SDOx Data Output Rise Time
—
—
—
ns
See parameter DO31
and Note 4
SP35
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
6
20
ns
—
SP36
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
ns
—
SP40
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP41
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
30
—
—
ns
—
SP50
TssL2scH,
TssL2scL
SSx ↓ to SCKx ↑ or SCKx ↓
Input
120
—
—
ns
—
SP51
TssH2doZ
SSx ↑ to SDOx Output
High-Impedance(4)
10
—
50
ns
—
SP52
TscH2ssH, SSx ↑ after SCKx Edge
TscL2ssH
1.5 TCY + 40
—
—
ns
See Note 4
Note 1:
2:
3:
4:
See Note 3
These parameters are characterized, but are not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not
violate this specification.
Assumes 50 pF load on all SPIx pins.
DS70657E-page 446
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-30:
I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE)
SCLx
IM31
IM34
IM30
IM33
SDAx
Stop
Condition
Start
Condition
Note: Refer to Figure 30-1 for load conditions.
FIGURE 30-31:
I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE)
IM20
IM21
IM11
IM10
SCLx
IM26
IM11
IM10
IM25
IM33
SDAx
In
IM40
IM40
IM45
SDAx
Out
Note: Refer to Figure 30-1 for load conditions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 447
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-48: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
IM10
IM11
IM20
IM21
IM25
IM26
IM30
IM31
IM33
IM34
IM40
IM45
IM50
IM51
Note 1:
2:
3:
4:
Characteristic
Min.(1)
Max.
Units
Conditions
—
μs
—
TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 2)
—
μs
—
400 kHz mode TCY/2 (BRG + 2)
(2)
TCY/2 (BRG + 2)
—
μs
—
1 MHz mode
THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 2)
—
μs
—
—
μs
—
400 kHz mode TCY/2 (BRG + 2)
—
μs
—
1 MHz mode(2) TCY/2 (BRG + 2)
TF:SCL
SDAx and SCLx 100 kHz mode
—
300
ns
CB is specified to be
Fall Time
from 10 to 400 pF
300
ns
400 kHz mode
20 + 0.1 CB
(2)
—
100
ns
1 MHz mode
TR:SCL SDAx and SCLx 100 kHz mode
—
1000
ns
CB is specified to be
Rise Time
from 10 to 400 pF
300
ns
400 kHz mode
20 + 0.1 CB
(2)
—
300
ns
1 MHz mode
TSU:DAT Data Input
100 kHz mode
250
—
ns
—
Setup Time
400 kHz mode
100
—
ns
40
—
ns
1 MHz mode(2)
THD:DAT Data Input
100 kHz mode
0
—
μs
—
Hold Time
400 kHz mode
0
0.9
μs
0.2
—
μs
1 MHz mode(2)
TSU:STA Start Condition 100 kHz mode TCY/2 (BRG + 2)
—
μs
Only relevant for
Setup Time
Repeated Start
—
μs
400 kHz mode TCY/2 (BRG + 2)
condition
(2)
TCY/2 (BRG + 2)
—
μs
1 MHz mode
THD:STA Start Condition 100 kHz mode TCY/2 (BRG + 2)
—
μs
After this period the
Hold Time
first
clock pulse is
—
μs
400 kHz mode
TCY/2 (BRG +2)
generated
(2)
TCY/2 (BRG + 2)
—
μs
1 MHz mode
TSU:STO Stop Condition 100 kHz mode TCY/2 (BRG + 2)
—
μs
—
Setup Time
—
μs
400 kHz mode TCY/2 (BRG + 2)
—
μs
1 MHz mode(2) TCY/2 (BRG + 2)
—
μs
—
THD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 2)
—
μs
Hold Time
400 kHz mode TCY/2 (BRG + 2)
—
μs
1 MHz mode(2) TCY/2 (BRG + 2)
TAA:SCL Output Valid
100 kHz mode
—
3500
ns
—
From Clock
400 kHz mode
—
1000
ns
—
—
400
ns
—
1 MHz mode(2)
TBF:SDA Bus Free Time 100 kHz mode
4.7
—
μs
Time the bus must be
free before a new
400 kHz mode
1.3
—
μs
transmission can start
(2)
0.5
—
μs
1 MHz mode
CB
Bus Capacitive Loading
—
400
pF
—
Pulse Gobbler Delay
65
390
ns
See Note 3
TPGD
BRG is the value of the I2C Baud Rate Generator. Refer to Section 19. “Inter-Integrated Circuit (I2C™)”
(DS70330) in the “dsPIC33E/PIC24E Family Reference Manual”. Please see the Microchip web site for
the latest family reference manual sections.
Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
Typical value for this parameter is 130 ns.
These parameters are characterized, but not tested in manufacturing.
DS70657E-page 448
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-32:
I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE)
SCLx
IS34
IS31
IS30
IS33
SDAx
Stop
Condition
Start
Condition
FIGURE 30-33:
I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE)
IS20
IS21
IS11
IS10
SCLx
IS30
IS25
IS31
IS26
IS33
SDAx
In
IS40
IS40
IS45
SDAx
Out
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 449
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-49: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
No.
IS10
IS11
IS20
IS21
IS25
IS26
IS30
IS31
IS33
IS34
IS40
IS45
IS50
IS51
Note
Characteristic
TLO:SCL Clock Low Time
THI:SCL
Clock High Time
Min.
Max.
Units
Conditions
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
4.7
1.3
0.5
4.0
—
—
—
—
μs
μs
μs
μs
—
400 kHz mode
0.6
—
μs
0.5
—
μs
1 MHz mode(1)
SDAx and SCLx 100 kHz mode
—
300
ns
TF:SCL
Fall Time
300
ns
400 kHz mode
20 + 0.1 CB
1 MHz mode(1)
—
100
ns
—
1000
ns
TR:SCL SDAx and SCLx 100 kHz mode
Rise Time
300
ns
400 kHz mode
20 + 0.1 CB
1 MHz mode(1)
—
300
ns
100 kHz mode
250
—
ns
TSU:DAT Data Input
Setup Time
400 kHz mode
100
—
ns
100
—
ns
1 MHz mode(1)
100 kHz mode
0
—
μs
THD:DAT Data Input
Hold Time
400 kHz mode
0
0.9
μs
0
0.3
μs
1 MHz mode(1)
100 kHz mode
4.7
—
μs
TSU:STA Start Condition
Setup Time
400 kHz mode
0.6
—
μs
0.25
—
μs
1 MHz mode(1)
100 kHz mode
4.0
—
μs
THD:STA Start Condition
Hold Time
400 kHz mode
0.6
—
μs
0.25
—
μs
1 MHz mode(1)
100 kHz mode
4.7
—
μs
TSU:STO Stop Condition
Setup Time
400 kHz mode
0.6
—
μs
0.6
—
μs
1 MHz mode(1)
100 kHz mode
4
—
μs
THD:STO Stop Condition
Hold Time
400 kHz mode
0.6
—
μs
0.25
μs
1 MHz mode(1)
100 kHz mode
0
3500
ns
TAA:SCL Output Valid
From Clock
400 kHz mode
0
1000
ns
0
350
ns
1 MHz mode(1)
100 kHz mode
4.7
—
μs
TBF:SDA Bus Free Time
400 kHz mode
1.3
—
μs
0.5
—
μs
1 MHz mode(1)
CB
Bus Capacitive Loading
—
400
pF
Pulse Gobbler Delay
65
390
ns
TPGD
1: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
2: The Typical value for this parameter is 130 ns.
3: These parameters are characterized, but not tested in manufacturing.
DS70657E-page 450
Preliminary
—
—
Device must operate at a
minimum of 1.5 MHz
Device must operate at a
minimum of 10 MHz
—
CB is specified to be from
10 to 400 pF
CB is specified to be from
10 to 400 pF
—
—
Only relevant for Repeated
Start condition
After this period, the first
clock pulse is generated
—
—
—
Time the bus must be free
before a new transmission
can start
—
See Note 2
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-34:
CiTx Pin
(output)
ECAN MODULE I/O TIMING CHARACTERISTICS
New Value
Old Value
CA10 CA11
CiRx Pin
(input)
CA20
TABLE 30-50: ECAN MODULE I/O TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param
No.
Characteristic(1)
Symbol
Min.
Typ.(2)
Max.
Units
Conditions
CA10
TioF
Port Output Fall Time
—
—
—
ns
See parameter DO32
CA11
TioR
Port Output Rise Time
—
—
—
ns
See parameter DO31
CA20
Tcwf
Pulse Width to Trigger
CAN Wake-up Filter
120
—
—
ns
Note 1:
2:
—
These parameters are characterized but not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
FIGURE 30-35:
UART MODULE I/O TIMING CHARACTERISTICS
UA20
UiRX
UITX
MSb In
Bit 6-1
LSb In
UA10
TABLE 30-51: UART MODULE I/O TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤TA ≤+125°C
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic(1)
UA10
Tuabaud
UA11
Fbaud
UART Baud Frequency
UA20
Tcwf
Start Bit Pulse Width to Trigger
UART Wake-up
Note 1:
2:
UART Baud Time
Min.
Typ.(2)
Max.
Units
Conditions
66.67
—
—
ns
—
—
—
15
Mbps
—
500
—
—
ns
—
These parameters are characterized but not tested in manufacturing.
Data in “Typical” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 451
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-52: OP AMP/COMPARATOR SPECIFICATIONS
Standard Operating Conditions (see Note 3): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
—
19
—
ns
V+ input step of 100 mV
V- input held at VDD/2
—
—
10
µs
—
—
±10
—
mV
—
—
30
—
mV
—
—
20
—
ns
—
90
—
db
—
AVSS
—
AVDD
V
—
—
9
—
V/µs
—
55
—
Degree G = 100V/V; 10 pF load
—
40
—
Degree
—
20
—
db
—
10
—
MHz
10 pF load
—
6
—
MHz
10 pF load
AVSS
—
AVDD
V
—
40
—
db
—
±5
—
mV
—
—
90
—
db
—
—
—
—
—
—
—
—
—
Comparator AC Characteristics
CM10
TRESP
Response Time
CM11
TMC2OV
Comparator Mode
Change to Output Valid
Comparator DC Characteristics
CM30
VOFFSET
CM31
VHYST
Comparator Offset
Voltage
Input Hysteresis Voltage
CM32
CM33
TRISE/
TFALL
VGAIN
Comparator Output
Rise/Fall Time
Open Loop Voltage Gain
CM34
VICM
CM20
SR
Input Common Mode
Voltage
Op amp AC Characteristics
CM21a PM
CM21b PM
CM22
GM
Slew Rate
Phase Margin
(Configuration A(4))
Phase Margin
(Configuration B(5))
Gain Margin
CM23a GBW
Gain Bandwidth
(Configuration A(4))
CM23b GBW
Gain Bandwidth
(Configuration B(5))
Op amp DC Characteristics
CM40
VCMR
CM41
CMRR
CM42
VOFFSET
Common Mode Input
Voltage Range
Common Mode
Rejection ratio
Op amp Offset Voltage
CM43
VGAIN
Open Loop Voltage Gain
CM44
IOS
Input Offset Current
CM45
IB
Input Bias Current
Note 1:
2:
3:
4:
5:
1 pF load capacitance
on input
10 pF load
G = 100V/V; 10 pF load
G = 100V/V; 10 pF load
—
VCM = AVDD/2
See Pad leakage
currents in Table 30-10
See Pad leakage
currents in Table 30-10
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Resistances can vary by ±10% between Op amps.
Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
See Figure 25-5 for configuration information.
See Figure 25-6 for configuration information.
DS70657E-page 452
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-52: OP AMP/COMPARATOR SPECIFICATIONS (CONTINUED)
Standard Operating Conditions (see Note 3): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
No.
Symbol
CM46
IOUT
CM48
RFEEDBACK
CM49a VOADC
CM49b VOUT
CM51
RINT1(2)
Note 1:
2:
3:
4:
5:
Characteristic
Output Current
Feedback Resistance
Value
Output Voltage
Measured at OAx using
ADC(4)
Output Voltage
Measured at OAxOUT
pin(4,5)
Internal Resistance 1
(Configuration A(4) and
B(5))
Min.
Typ.(1)
Max.
Units
—
—
420
µA
8
—
—
kΩ
AVSS + 0.077
AVSS + 0.037
AVSS + 0.018
AVSS + 0.210
AVSS + 0.100
AVSS + 0.050
—
—
—
—
—
—
AVDD – 0.077
AVDD – 0.037
AVDD – 0.018
AVDD – 0.210
AVDD – 0.100
AVDD – 0.050
V
V
V
V
V
V
IOUT = 420 µA
IOUT = 200 µA
IOUT = 100 µA
IOUT = 420 µA
IOUT = 200 µA
IOUT = 100 µA
198
264
317
Ω
Min = -40ºC
Typ = +25ºC
Max = +125ºC
Conditions
With minimum value of
RFEEDBACK (CM48)
—
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Resistances can vary by ±10% between Op amps.
Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
See Figure 25-5 for configuration information.
See Figure 25-6 for configuration information.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 453
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-53: OP AMP/COMPARATOR REFERENCE VOLTAGE SETTLING TIME SPECIFICATIONS
Standard Operating Conditions (see Note 2): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param.
Symbol
Characteristic
Min.
Typ.
Max.
Units
Conditions
Settling Time
—
1
10
μs
See Note 1
VR310 TSET
Note 1: Settling time measured while CVRR = 1 and CVR<3:0> bits transition from ‘0000’ to ‘1111’.
2: Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
TABLE 30-54: OP AMP/COMPARATOR VOLTAGE REFERENCE SPECIFICATIONS
Standard Operating Conditions (see Note 1): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
DC CHARACTERISTICS
Param
No.
Symbol
Characteristics
Min.
Typ.
Max.
Units
Conditions
CVRSRC/24
—
CVRSRC/32
LSb
—
VRD310 CVRES
Resolution
VRD311 CVRAA
Absolute Accuracy
—
±25
—
mV
VRD313 CVRSRC
Input Reference Voltage
0
—
AVDD + 0.3
V
—
VRD314 CVROUT
Buffer Output Resistance
—
1.5k
—
Ω
—
Note 1:
CVRSRC = 3.3V
Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
DS70657E-page 454
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-55: CTMU CURRENT SOURCE SPECIFICATIONS
DC CHARACTERISTICS
Param
No.
Symbol
Standard Operating Conditions:3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
Characteristic
Min.
Typ.
Max.
Units
Conditions
CTMU CURRENT SOURCE
CTMUI1
IOUT1
Base Range(1)
—
0.55
—
µA
CTMUICON<9:8> = 01
CTMUI2
IOUT2
10x Range(1)
—
5.5
—
µA
CTMUICON<9:8> = 10
CTMUI3
IOUT3
100x Range(1)
—
55
—
µA
CTMUICON<9:8> = 11
CTMUI4
IOUT4
CTMUFV1 VF
CTMUFV2 VFVR
Note 1:
2:
(1)
1000x Range
—
550
—
µA
CTMUICON<9:8> = 00
Temperature Diode Forward
Voltage(1,2)
—
0.598
—
V
TA = +25ºC,
CTMUICON<9:8> = 01
—
0.658
—
V
TA = +25ºC,
CTMUICON<9:8> = 10
—
0.721
—
V
TA = +25ºC,
CTMUICON<9:8> = 11
—
-1.92
—
mV/ºC CTMUICON<9:8> = 01
—
-1.74
—
mV/ºC CTMUICON<9:8> = 10
—
-1.56
—
mV/ºC CTMUICON<9:8> = 11
Temperature Diode Rate of
Change(1,2)
Nominal value at center point of current trim range (CTMUICON<15:10> = 000000).
Parameters are characterized but not tested in manufacturing. Measurements taken with the following
conditions:
• VREF+ = AVDD = 3.3V
• ADC configured for 10-bit mode
• ADC module configured for conversion speed of 500 ksps
• All PMD bits are cleared (PMDx = 0)
• Executing a while(1) statement
• Device operating from the FRC with no PLL
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 455
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-56: ADC MODULE SPECIFICATIONS
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Standard Operating Conditions (see Note 1): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
Min.
Typ.
Max.
Units
Lesser of
VDD + 0.3
or 3.6
V
VSS + 0.3
V
Conditions
Device Supply
AD01
AVDD
Module VDD Supply
AD02
AVSS
Module VSS Supply
AD05
VREFH
Reference Voltage High
Greater of
VDD – 0.3
or 3.0
—
VSS – 0.3
—
—
—
Reference Inputs
AD05a
AD06
VREFL
Reference Voltage Low
AD06a
AVSS + 2.5
—
AVDD
V
See Note 1
VREFH = VREF+
VREFL = VREF-
3.0
—
3.6
V
VREFH = AVDD
VREFL = AVSS = 0
AVSS
—
AVDD – 2.5
V
See Note 1
0
—
0
V
VREFH = AVDD
VREFL = AVSS = 0
AD07
VREF
Absolute Reference
Voltage
2.5
—
3.6
V
VREF = VREFH - VREFL
AD08
IREF
Current Drain
—
—
—
—
10
600
μA
μA
ADC off
ADC on
AD09
IAD
Operating Current
—
5
—
mA
—
2
—
mA
ADC operating in 10-bit
mode, see Note 1
ADC operating in 12-bit
mode, see Note 1
Analog Input
AD12
VINH
Input Voltage Range VINH
VINL
—
VREFH
V
This voltage reflects Sample
and Hold Channels 0, 1, 2,
and 3 (CH0-CH3), positive
input
AD13
VINL
Input Voltage Range VINL
VREFL
—
AVSS + 1V
V
This voltage reflects Sample
and Hold Channels 0, 1, 2,
and 3 (CH0-CH3), negative
input
AD17
RIN
Recommended Impedance of Analog Voltage
Source
—
—
200
Ω
Impedance to achieve
maximum performance of
ADC
Note 1:
Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
DS70657E-page 456
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-57: ADC MODULE SPECIFICATIONS (12-BIT MODE)
Standard Operating Conditions (see Note 1): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ.
Max.
Units
Conditions
ADC Accuracy (12-bit Mode) – Measurements with external VREF+/VREFAD20a
Nr
Resolution
bits
—
AD21a
INL
Integral Nonlinearity
-2
12 data bits
—
+2
LSb
VINL = AVSS = VREFL = 0V, AVDD
= VREFH = 3.6V
AD22a
DNL
Differential Nonlinearity
>-1
—
<1
LSb
VINL = AVSS = VREFL = 0V, AVDD
= VREFH = 3.6V
AD23a
GERR
Gain Error
1.25
1.5
3
LSb
VINL = AVSS = VREFL = 0V, AVDD
= VREFH = 3.6V
AD24a
EOFF
Offset Error
1.25
1.52
2
LSb
VINL = AVSS = VREFL = 0V, AVDD
= VREFH = 3.6V
AD25a
—
Monotonicity
—
—
—
—
Guaranteed
ADC Accuracy (12-bit Mode) – Measurements with internal VREF+/VREFAD20a
Nr
Resolution
AD21a
INL
Integral Nonlinearity
-2
12 data bits
—
+2
LSb
bits
VINL = AVSS = 0V, AVDD = 3.6V
—
AD22a
DNL
Differential Nonlinearity
>-1
—
<1
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD23a
GERR
Gain Error
2
3
7
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD24a
EOFF
Offset Error
2
3
5
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD25a
—
Monotonicity
—
—
—
—
AD30a
THD
Total Harmonic Distortion
AD31a
SINAD
Signal to Noise and
Distortion
AD32a
SFDR
Spurious Free Dynamic
Range
AD33a
FNYQ
Input Signal Bandwidth
AD34a
ENOB
Effective Number of Bits
Guaranteed
Dynamic Performance (12-bit Mode)
Note 1:
—
—
-75
dB
—
68.5
69.5
—
dB
—
80
—
—
dB
—
—
—
250
kHz
—
11.09
11.3
—
bits
—
Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 457
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-58: ADC MODULE SPECIFICATIONS (10-BIT MODE)
Standard Operating Conditions (see Note 1): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
AC CHARACTERISTICS
Param
No.
Symbol
Characteristic
Min.
Typ.
Max.
Units
Conditions
ADC Accuracy (10-bit Mode) – Measurements with external VREF+/VREFAD20b
Nr
Resolution
AD21b
INL
Integral Nonlinearity
-1.5
10 data bits
—
+1.5
LSb
bits
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
—
AD22b
DNL
Differential Nonlinearity
>-1
—
<1
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD23b
GERR
Gain Error
1
3
6
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD24b
EOFF
Offset Error
1
2
3
LSb
VINL = AVSS = VREFL = 0V,
AVDD = VREFH = 3.6V
AD25b
—
Monotonicity
—
—
—
—
AD20b
Nr
Resolution
AD21b
INL
Integral Nonlinearity
-1.5
—
AD22b
DNL
Differential Nonlinearity
>-1
—
AD23b
GERR
Gain Error
1
5
6
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD24b
EOFF
Offset Error
1
2
5
LSb
VINL = AVSS = 0V, AVDD = 3.6V
AD25b
—
Monotonicity
—
—
—
—
Guaranteed
ADC Accuracy (10-bit Mode) – Measurements with internal VREF+/VREF10 data bits
bits
—
+1.5
LSb
VINL = AVSS = 0V, AVDD = 3.6V
<1
LSb
VINL = AVSS = 0V, AVDD = 3.6V
Guaranteed
Dynamic Performance (10-bit Mode)
AD30b
THD
Total Harmonic Distortion
—
—
-64
dB
—
AD31b
SINAD
Signal to Noise and
Distortion
57
58.5
—
dB
—
AD32b
SFDR
Spurious Free Dynamic
Range
72
—
—
dB
—
AD33b
FNYQ
Input Signal Bandwidth
—
—
550
kHz
—
AD34b
ENOB
Effective Number of Bits
9.16
9.4
—
bits
—
Note 1:
Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
DS70657E-page 458
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-36:
ADC CONVERSION (12-BIT MODE) TIMING CHARACTERISTICS
(ASAM = 0, SSRC<2:0> = 000, SSRCG = 0)
AD50
ADCLK
Instruction
Execution
Set SAMP
Clear SAMP
SAMP
AD61
AD60
TSAMP
AD55
DONE
AD1IF
1
2
3
4
5
6
7
8
9
1 – Software sets AD1CON1. SAMP to start sampling.
5 – Convert bit 11.
2 – Sampling starts after discharge period. TSAMP is described in
Section 16. “Analog-to-Digital Converter (ADC)” (DS70621) of the
“dsPIC33E/PIC24E Family Reference Manual”.
3 – Software clears AD1CON1. SAMP to start conversion.
6 – Convert bit 10.
4 – Sampling ends, conversion sequence starts.
9 – One TAD for end of conversion.
© 2011-2012 Microchip Technology Inc.
Preliminary
7 – Convert bit 1.
8 – Convert bit 0.
DS70657E-page 459
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-59: ADC CONVERSION (12-BIT MODE) TIMING REQUIREMENTS
Standard Operating Conditions (see Note 2): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
AD50
AD51
TAD
tRC
AD55 tCONV
AD56 FCNV
AD57a TSAMP
AD57b TSAMP
AD60
tPCS
Characteristic
Min.
Typ.
Clock Parameters
ADC Clock Period
117.6
—
ADC Internal RC Oscillator Period
—
250
Conversion Rate
Conversion Time
—
14 TAD
Throughput Rate
—
—
Sample Time when Sampling any
3 TAD
—
ANx Input
3 TAD
Sample Time when Sampling the
—
Op amp Outputs (Configuration A(4)
and Configuration B(5))
Timing Parameters
2 TAD
—
Conversion Start from Sample
Trigger(6)
Max.
Units
Conditions
—
—
ns
ns
—
—
500
—
ns
Ksps
—
—
—
—
—
—
—
3 TAD
—
Auto convert trigger not
selected
Sample Start from Setting
2 TAD
—
3 TAD
—
—
Sample (SAMP) bit(6)
Conversion Completion to
—
0.5 TAD
—
—
—
AD62 tCSS
Sample Start (ASAM = 1)(6)
Time to Stabilize Analog Stage
—
—
20
μs
See Note 3
AD63 tDPU
from ADC Off to ADC On(6)
Note 1: Because the sample caps will eventually lose charge, clock rates below 10 kHz may affect linearity
performance, especially at elevated temperatures.
2: Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
3: The parameter tDPU is the time required for the ADC module to stabilize at the appropriate level when the
module is turned on (ADON (AD1CON1<15>) = ‘1’). During this time, the ADC result is indeterminate.
4: See Figure 25-5 for configuration information.
5: See Figure 25-6 for configuration information.
6: These parameters are characterized, but not tested in manufacturing.
AD61
tPSS
DS70657E-page 460
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
FIGURE 30-37:
ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS
(CHPS<1:0> = 01, SIMSAM = 0, ASAM = 0, SSRC<2:0> = 000, SSRCG = 0)
AD50
ADCLK
Instruction
Execution Set SAMP
Clear SAMP
SAMP
AD61
AD60
AD55
TSAMP
AD55
DONE
AD1IF
1
2
3
4
5
6
7
8
5
6
7
1 – Software sets AD1CON1. SAMP to start sampling.
5 – Convert bit 9.
2 – Sampling starts after discharge period. TSAMP is described in
Section 16. “Analog-to-Digital Converter (ADC)” (DS70621) of the
“dsPIC33E/PIC24E Family Reference Manual”.
3 – Software clears AD1CON1. SAMP to start conversion.
6 – Convert bit 8.
8
7 – Convert bit 0.
8 – One TAD for end of conversion.
4 – Sampling ends, conversion sequence starts.
FIGURE 30-38:
ADC CONVERSION (10-BIT MODE) TIMING CHARACTERISTICS (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 1, SSRC<2:0> = 111, SSRCG = 0, SAMC<4:0> = 00010)
AD50
ADCLK
Instruction
Set ADON
Execution
AD62
SAMP
TSAMP
AD55
TSAMP
AD55
AD55
AD1IF
DONE
1
2
3
4
5
6
7
3
4
5
6
8
1 – Software sets AD1CON1. ADON to start AD operation.
5 – Convert bit 0.
2 – Sampling starts after discharge period. TSAMP is described in
Section 16. “Analog-to-Digital Converter (ADC)” (DS70621)
of the “dsPIC33E/PIC24E Family Reference Manual”.
–
Convert bit 9.
3
6 – One TAD for end of conversion.
7 – Begin conversion of next channel.
8 – Sample for time specified by SAMC<4:0>.
4 – Convert bit 8.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 461
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE 30-60: ADC CONVERSION (10-BIT MODE) TIMING REQUIREMENTS
Standard Operating Conditions (see Note 1): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤ TA ≤ +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
AD50
AD51
TAD
tRC
AD55
AD56
tCONV
FCNV
Characteristic
Min.
Typ.(1)
Max.
Units
Conditions
—
—
ns
ns
—
—
—
1.1
—
Msps
Clock Parameters
ADC Clock Period
76
—
ADC Internal RC Oscillator Period
—
250
Conversion Rate
Conversion Time
—
12 TAD
Throughput Rate
—
—
—
Using Simultaneous
Sampling
—
Sample Time when Sampling any
2 TAD
—
—
—
ANx Input
4 TAD
—
—
—
—
AD57b TSAMP Sample Time when Sampling the
Op amp Outputs (Configuration A(4)
and Configuration B(5))
Timing Parameters
Conversion Start from Sample
2 TAD
—
3 TAD
—
Auto-Convert Trigger
AD60 tPCS
Trigger(6)
not selected
Sample Start from Setting
2 TAD
—
3 TAD
—
—
AD61 tPSS
Sample (SAMP) bit(6)
Conversion Completion to
—
0.5 TAD
—
—
—
AD62 tCSS
Sample Start (ASAM = 1)(6)
Time to Stabilize Analog Stage
—
—
20
μs
See Note 3
AD63 tDPU
from ADC Off to ADC On(6)
Note 1: Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality
is tested, but not characterized. Analog modules: ADC, Op amp/Comparator, and Comparator voltage
reference, will have degraded performance. Refer to parameter BO10 in Table 30-12 for the minimum and
maximum BOR values.
2: Because the sample caps will eventually lose charge, clock rates below 10 kHz may affect linearity
performance, especially at elevated temperatures.
3: The parameter tDPU is the time required for the ADC module to stabilize at the appropriate level when the
module is turned on (AD1CON1<ADON> = 1). During this time, the ADC result is indeterminate.
4: See Figure 25-5 for configuration information.
5: See Figure 25-6 for configuration information.
6: These parameters are characterized, but not tested in manufacturing.
AD57a TSAMP
TABLE 30-61: DMA MODULE TIMING REQUIREMENTS
AC CHARACTERISTICS
Param
No.
DM1
Note 1:
2:
Characteristic
DMA Byte/Word Transfer Latency
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C ≤TA ≤+125°C for Extended
Min.
Typ.
Max.
Units
Conditions
1 TCY(2)
—
—
ns
—
These parameters are characterized, but not tested in manufacturing.
Because DMA transfers use the CPU data bus, this time is dependent on other functions on the bus.
DS70657E-page 462
Preliminary
© 2011-2012 Microchip Technology Inc.
DC AND AC DEVICE CHARACTERISTICS GRAPHS
Note:
The graphs provided following this note are a statistical summary based on a limited number of samples and are provided for design guidance purposes
only. The performance characteristics listed herein are not tested or guaranteed. In some graphs, the data presented may be outside the specified operating
range (e.g., outside specified power supply range) and therefore, outside the warranted range.
FIGURE 31-1:
VOH – 4x DRIVER PINS
-0.045
VOL(V)
0.050
3.6V
3.6V
0.045
-0.040
0.040
3.3V
-0.035
3.3V
0.035
3V
IOH(A)
-0.030
-0.025
-0.020
Absolute Maximum
-0.015
3V
0.030
0.025
0.020
0.015
Preliminary
-0.010
0.010
-0.005
0.005
Absolute Maximum
0.000
0.000
0.00
0.50
FIGURE 31-2:
-0.080
1.00
1.50
2.00
2.50
3.00
3.50
0.00
4.00
VOH – 8x DRIVER PINS
FIGURE 31-4:
VOH(V)
IOH(A)
-0.040
DS70657E-page 463
0 030
-0.030
Absolute Maximum
0.010
0.000
0.000
1.50
2.00
2.50
3.00
3.50
4.00
3.00
3.50
4.00
VOL – 8x DRIVER PINS
8X
VOL(V)
3.6V
3.3V
3V
0.030
-0.010
1.00
2.50
0.040
0 020
0.020
0.50
2.00
0.050
-0.020
0.00
1.50
0.060
3V
-0.050
1.00
0.070
3.3V
-0.060
0.50
0.080
3.6V
-0.070
IOH(A)
VOL – 4x DRIVER PINS
VOH (V)
-0.050
IOH(A)
FIGURE 31-3:
Absolute Maximum
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
4.00
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
31.0
FIGURE 31-7:
TYPICAL IPD CURRENT @ VDD = 3.3V
TYPICAL IDOZE CURRENT @ VDD = 3.3V
800.00
45.00
700.00
40.00
IDOZE
OZE Current (mA)
IPD Current (µA)
600.00
500.00
400.00
300.00
200.00
35.00
30.00
25.00
20.00
15.00
10.00
5.00
100.00
0.00
0.00
Preliminary
-40 -30 -20 -10
0
1:1
10 20 30 40 50 60 70 80 90 100 110 120
1:2
1:4
TYPICAL IDD CURRENT @ VDD = 3.3V
FIGURE 31-8:
45.00
1:32
1:64
1:128
TYPICAL IIDLE CURRENT @ VDD = 3.3V
25.00
40.00
35.00
20.00
30.00
IIDLE Current (mA)
© 2011-2012 Microchip Technology Inc.
Average (mA)
1:16
Doze Ratio
Temperature (Celsius)
FIGURE 31-6:
1:8
25.00
20.00
IDD (EC+PLL)
15.00
10.00
15.00
10.00
IIDLE (EC+PLL)
5.00
5.00
IDD (EC)
0.00
0
10
IIDLE (EC)
0.00
20
30
40
MIPS
50
60
70
0
10
20
30
40
MIPS
50
60
70
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
DS70657E-page 464
FIGURE 31-5:
TYPICAL CTMU TEMPERATURE DIODE
FORWARD VOLTAGE
7380
0.850
7370
0.800
7360
0.750
7350
0.700
VF = 0.721
0.650
VF = 0.658
7340
7330
7320
0.600
65 µ
A, V
F
VR
6.5
VF = 0.598
= -1
. 56
µA,
VFV
0.550
7310
0.500
7300
0.450
7290
0.400
7280
mV/
ºC
R
= -1
0.6
5
.74
mV
/ºC
µA,
V
F VR
= -1
.9 2
mV
/ºC
0.350
Preliminary
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120
FIGURE 31-10:
TYPICAL LPRC FREQUENCY @ VDD = 3.3V
33
32
31
DS70657E-page 465
30
-40 -30 -20 -10
0
10
20
30
40
50
60
Temperature (Celsius)
-40 -30 -20 -10
0
10
20
30
40
50
60
Temperature (Celsius)
Temperature (Celsius)
LPRC Frequency (kHz)
FIGURE 31-11:
Forward Voltage (V)
FRC Frequency (kHz)
TYPICAL FRC FREQUENCY @ VDD = 3.3V
70
80
90 100 110 120
70
80
90
100 110 120 130
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
© 2011-2012 Microchip Technology Inc.
FIGURE 31-9:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 466
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
32.0
PACKAGING INFORMATION
32.1
Package Marking Information
28-Lead SPDIP (.300”)
Example
dsPIC33EP64GP
502-I/SP e3
28-Lead SOIC (7.50 mm)
Example
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
dsPIC33EP64GP
502-I/SO e3
0610017
YYWWNNN
28-Lead SSOP (5.30 mm)
Example
dsPIC33EP64
GP502-I/SS e3
0610017
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 467
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
32.1
Package Marking Information (Continued)
28-Lead QFN-S (6x6x0.9 mm)
Example
PIN 1
PIN 1
XXXXXXXX
XXXXXXXX
YYWWNNN
33EP64GP
502-I/MM
0610017
36-Lead VTLA (TLA)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
dsPIC
33EP64GP
504-I/TL e3
44-Lead VTLA (TLA)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
dsPIC
33EP64GP
504-I/TL e3
44-Lead TQFP (10x10x1 mm)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
dsPIC
33EP64GP
504-I/PT e3
0610017
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
DS70657E-page 468
0610017
0610017
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
32.1
Package Marking Information (Continued)
44-Lead QFN (8x8x0.9 mm)
Example
PIN 1
PIN 1
dsPIC
33EP64GP
504-I/ML
0610017
XXXXXXXXXXX
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
64-Lead QFN (9x9x0.9 mm)
Example
PIN 1
PIN 1
XXXXXXXXXXX
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
dsPIC33EP
64GP506
e3
-I/MR
0610017
64-Lead TQFP (10x10x1 mm)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
dsPIC33EP
64GP506
506-I/PT e3
0510017
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 469
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
32.2
Package Details
/HDG6NLQQ\3ODVWLF'XDO,Q/LQH 63 ±PLO%RG\>63',3@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
N
NOTE 1
E1
1
2 3
D
E
A2
A
L
c
b1
A1
b
e
eB
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
,1&+(6
0,1
1
120
0$;
3LWFK
H
7RSWR6HDWLQJ3ODQH
$
±
±
0ROGHG3DFNDJH7KLFNQHVV
$
%DVHWR6HDWLQJ3ODQH
$
±
±
6KRXOGHUWR6KRXOGHU:LGWK
(
0ROGHG3DFNDJH:LGWK
(
2YHUDOO/HQJWK
'
7LSWR6HDWLQJ3ODQH
/
/HDG7KLFNQHVV
F
E
E
H%
±
±
8SSHU/HDG:LGWK
/RZHU/HDG:LGWK
2YHUDOO5RZ6SDFLQJ†
%6&
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
†6LJQLILFDQW&KDUDFWHULVWLF
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS70657E-page 470
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 471
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70657E-page 472
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 473
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
/HDG3ODVWLF6KULQN6PDOO2XWOLQH 66 ±PP%RG\>6623@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
N
E
E1
1 2
NOTE 1
b
e
c
A2
A
φ
A1
L
L1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
±
%6&
±
0ROGHG3DFNDJH7KLFNQHVV
$
6WDQGRII
$
±
±
2YHUDOO:LGWK
(
0ROGHG3DFNDJH:LGWK
(
2YHUDOO/HQJWK
'
)RRW/HQJWK
/
)RRWSULQW
/
5()
/HDG7KLFNQHVV
F
±
)RRW$QJOH
ƒ
ƒ
ƒ
/HDG:LGWK
E
±
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS70657E-page 474
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 475
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
/HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 00 ±[[PP%RG\>4)16@
ZLWKPP&RQWDFW/HQJWK
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
D2
EXPOSED
PAD
e
E2
E
b
2
2
1
1
K
N
N
L
NOTE 1
TOP VIEW
BOTTOM VIEW
A
A3
A1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
6WDQGRII
$
&RQWDFW7KLFNQHVV
$
2YHUDOO:LGWK
(
([SRVHG3DG:LGWK
(
2YHUDOO/HQJWK
'
([SRVHG3DG/HQJWK
%6&
5()
%6&
%6&
'
&RQWDFW:LGWK
E
&RQWDFW/HQJWK
/
&RQWDFWWR([SRVHG3DG
.
±
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
3DFNDJHLVVDZVLQJXODWHG
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
±
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS70657E-page 476
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
/HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 00 ±[[PP%RG\>4)16@
ZLWKPP&RQWDFW/HQJWK
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 477
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70657E-page 478
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 479
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70657E-page 480
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 481
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
/HDG3ODVWLF7KLQ4XDG)ODWSDFN 37 ±[[PP%RG\PP>74)3@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
D1
E
e
E1
N
b
NOTE 1
1 2 3
NOTE 2
α
A
c
φ
β
L
A1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI/HDGV
A2
L1
0,//,0(7(56
0,1
1
120
0$;
/HDG3LWFK
H
2YHUDOO+HLJKW
$
±
%6&
±
0ROGHG3DFNDJH7KLFNQHVV
$
6WDQGRII
$
±
)RRW/HQJWK
/
)RRWSULQW
/
5()
)RRW$QJOH
2YHUDOO:LGWK
(
ƒ
%6&
ƒ
2YHUDOO/HQJWK
'
%6&
0ROGHG3DFNDJH:LGWK
(
%6&
0ROGHG3DFNDJH/HQJWK
'
%6&
ƒ
/HDG7KLFNQHVV
F
±
/HDG:LGWK
E
0ROG'UDIW$QJOH7RS
ƒ
ƒ
ƒ
0ROG'UDIW$QJOH%RWWRP
ƒ
ƒ
ƒ
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
&KDPIHUVDWFRUQHUVDUHRSWLRQDOVL]HPD\YDU\
'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRUSURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS70657E-page 482
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 483
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
/HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 0/ ±[PP%RG\>4)1@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
D
D2
EXPOSED
PAD
e
E
E2
b
2
2
1
N
1
N
NOTE 1
TOP VIEW
K
L
BOTTOM VIEW
A
A3
A1
8QLWV
'LPHQVLRQ/LPLWV
1XPEHURI3LQV
0,//,0(7(56
0,1
1
120
0$;
3LWFK
H
2YHUDOO+HLJKW
$
6WDQGRII
$
&RQWDFW7KLFNQHVV
$
2YHUDOO:LGWK
(
([SRVHG3DG:LGWK
(
2YHUDOO/HQJWK
'
([SRVHG3DG/HQJWK
%6&
5()
%6&
%6&
'
&RQWDFW:LGWK
E
&RQWDFW/HQJWK
/
&RQWDFWWR([SRVHG3DG
.
±
1RWHV
3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD
3DFNDJHLVVDZVLQJXODWHG
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
%6& %DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
5() 5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
±
0LFURFKLS 7HFKQRORJ\ 'UDZLQJ &%
DS70657E-page 484
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
/HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 0/ ±[PP%RG\>4)1@
1RWH
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 485
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70657E-page 486
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 487
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70657E-page 488
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
64-Lead Plastic Thin Quad Flatpack (PT) – 10x10x1 mm Body, 2.00 mm Footprint [TQFP]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D1
E
e
E1
N
b
NOTE 1
123
NOTE 2
α
A
φ
c
A2
β
A1
L
L1
Units
Dimension Limits
Number of Leads
MILLIMETERS
MIN
N
NOM
MAX
64
Lead Pitch
e
Overall Height
A
–
0.50 BSC
–
Molded Package Thickness
A2
0.95
1.00
1.05
Standoff
A1
0.05
–
0.15
Foot Length
L
0.45
0.60
0.75
Footprint
L1
1.20
1.00 REF
Foot Angle
φ
Overall Width
E
0°
12.00 BSC
3.5°
Overall Length
D
12.00 BSC
Molded Package Width
E1
10.00 BSC
Molded Package Length
D1
10.00 BSC
7°
Lead Thickness
c
0.09
–
0.20
Lead Width
b
0.17
0.22
0.27
Mold Draft Angle Top
α
11°
12°
13°
Mold Draft Angle Bottom
β
11°
12°
13°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Chamfers at corners are optional; size may vary.
3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-085B
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 489
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70657E-page 490
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
APPENDIX A:
REVISION HISTORY
Revision A (April 2011)
This is the initial released version of the document.
Revision B (July 2011)
This revision includes minor typographical and
formatting changes throughout the data sheet text.
All other major changes are referenced by their
respective section in Table A-1.
TABLE A-1:
MAJOR SECTION UPDATES
Section Name
Update Description
“High-Performance, 16-bit
Digital Signal Controllers
and Microcontrollers”
Changed all pin diagrams references of VLAP to TLA.
Section 4.0 “Memory
Organization”
Updated the All Resets values for CLKDIV and PLLFBD in the System Control
Register Map (see Table 4-35).
Section 5.0 “Flash Program Updated “one word” to “two words” in the first paragraph of Section 5.2 “RTSP
Memory”
Operation”.
Section 9.0 “Oscillator
Configuration”
Updated the PLL Block Diagram (see Figure 9-2).
Updated the Oscillator Mode, Fast RC Oscillator (FRC) with divide-by-N and PLL
(FRCPLL), by changing (FRCDIVN + PLL) to (FRCPLL).
Changed (FRCDIVN + PLL) to (FRCPLL) for COSC<2:0> = 001 and
NOSC<2:0> = 001 in the Oscillator Control Register (see Register 9-1).
Changed the POR value from 0 to 1 for the DOZE<1:0> bits, from 1 to 0 for the
FRCDIV<0> bit, and from 0 to 1 for the PLLPOST<0> bit; Updated the default
definitions for the DOZE<2:0> and FRCDIV<2:0> bits and updated all bit definitions
for the PLLPOST<1:0> bits in the Clock Divisor Register (see Register 9-2).
Changed the POR value from 0 to 1 for the PLLDIV<5:4> bits and updated the default
definitions for all PLLDIV<8:0> bits in the PLL Feedback Division Register (see
Register 9-2).
Section 22.0 “Charge Time Updated the bit definitions for the IRNG<1:0> bits in the CTMU Current Control
Measurement Unit (CTMU)” Register (see Register 22-3).
Section 25.0 “Op amp/
Comparator Module”
Updated the voltage reference block diagrams (see Figure 25-1 and Figure 25-2).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 491
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE A-1:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Section 30.0 “Electrical
Characteristics”
Update Description
Removed Voltage on VCAP with respect to Vss and added Note 5 in Absolute
Maximum Ratings(1).
Removed parameter DC18 (VCORE) and Note 3 from the DC Temperature and
Voltage Specifications (see Table 30-4).
Updated Note 1 in the DC Characteristics: Operating Current (IDD) (see Table 30-6).
Updated Note 1 in the DC Characteristics: Idle Current (IIDLE) (see Table 30-7).
Changed the Typical values for parameters DC60a-DC60d and updated Note 1 in the
DC Characteristics: Power-down Current (IPD) (see Table 30-8).
Updated Note 1 in the DC Characteristics: Doze Current (IDOZE) (see Table 30-9).
Updated Note 2 in the Electrical Characteristics: BOR (see Table 30-12).
Updated parameters CM20 and CM31, and added parameters CM44 and CM45 in
the AC/DC Characteristics: Op amp/Comparator (see Table 30-14).
Added the Op amp/Comparator Reference Voltage Settling Time Specifications (see
Table 30-15).
Added Op amp/Comparator Voltage Reference DC Specifications (see Table 30-16).
Updated Internal FRC Accuracy parameter F20a (see Table 30-21).
Updated the Typical value and Units for parameter CTMUI1, and added parameters
CTMUI4, CTMUFV1, and CTMUFV2 to the CTMU Current Source Specifications (see
Table 30-55).
Section 31.0 “Packaging
Information”
Updated packages by replacing references of VLAP with TLA.
“Product Identification
System”
Changed VLAP to TLA.
DS70657E-page 492
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Revision C (December 2011)
This revision includes typographical and formatting
changes throughout the data sheet text.
In addition, where applicable, new sections were added
to each peripheral chapter that provide information and
links to related resources, as well as helpful tips. For
examples, see Section 20.1 “UART Helpful Tips”
and Section 3.6 “CPU Resources”.
TABLE A-2:
All occurrences of TLA were updated to VTLA
throughout the document, with the exception of the pin
diagrams (updated diagrams were not available at time
of publication).
A new chapter, Section 31.0 “DC and AC Device
Characteristics Graphs”, was added.
All other major changes are referenced by their
respective section in Table A-2.
MAJOR SECTION UPDATES
Section Name
Update Description
“16-bit Microcontrollers
and Digital Signal
Controllers (up to 256 KB
Flash and 32 KB SRAM)
with High-Speed PWM, Op
amps, and Advanced
Analog”
The content on the first page of this section was extensively reworked to provide the
reader with the key features and functionality of this device family in an “at-a-glance”
format.
Section 1.0 “Device
Overview”
Updated the dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, and
PIC24EPXXXGP/MC20X Block Diagram (see Figure 1-1), which now contains a CPU
block and a reference to the CPU diagram.
Updated the description and Note references in the Pinout I/O Descriptions for these
pins: C1IN2-, C2IN2-, C3IN2-, OA1OUT, OA2OUT, and OA3OUT (see Table 1-1).
Section 2.0 “Guidelines for
Getting Started with 16-bit
Digital Signal Controllers
and Microcontrollers”
Updated the Recommended Minimum Connection diagram (see Figure 2-1).
Section 3.0 “CPU”
Updated the dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, and
PIC24EPXXXGP/MC20X CPU Block Diagram (see Figure 3-1).
Updated the Status register definition in the Programmer’s Model (see Figure 3-2).
Section 4.0 “Memory
Organization”
Updated the Data Memory Maps (see Figure 4-6 and Figure 4-11).
Removed the DCB<1:0> bits from the OC1CON2, OC2CON2, OC3CON2, and
OC4CON2 registers in the Output Compare 1 Through Output Compare 4 Register
Map (see Table 4-10).
Added the TRIG1 and TRGCON1 registers to the PWM1 Generator 1 Register Map
(see Table 4-13).
Added the TRIG2 and TRGCON2 registers to the PWM1 Generator 1 Register Map
(see Table 4-14).
Added the TRIG3 and TRGCON3 registers to the PWM1 Generator 1 Register Map
(see Table 4-15).
Updated the second note in Section 4.7.1 “Bit-Reversed Addressing
Implementation”.
Section 8.0 “Direct Memory Updated the DMA Controller diagram (see Figure 8-1).
Access (DMA)”
Section 14.0 “Input
Capture”
Updated the bit values for the ICx clock source of the ICTSEL<12:10> bits in the
ICxCON1 register (see Register 14-1).
Section 15.0 “Output
Compare”
Updated the bit values for the OCx clock source of the OCTSEL<2:0> bits in the
OCxCON1 register (see Register 15-1).
Removed the DCB<1:0> bits from the Output Compare x Control Register 2 (see
Register 15-2).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 493
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE A-2:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 16.0 “High-Speed
PWM Module
(dsPIC33EPXXXMC20X/50X
and PIC24EPXXXMC20X
Devices Only)”
Updated the High-Speed PWM Module Register Interconnection Diagram (see
Figure 16-2).
Added the TRGCONx and TRIGx registers (see Register 16-12 and Register 16-14,
respectively).
Section 21.0 “Enhanced
CAN (ECAN™) Module
(dsPIC33EPXXXGP/MC50X
Devices Only)”
Updated the CANCKS bit value definitions in CiCTRL1: ECAN Control Register 1
(see Register 21-1).
Section 22.0 “Charge Time Updated the IRNG<1:0> bit value definitions and added Note 2 in the CTMU Current
Measurement Unit (CTMU)” Control Register (see Register 22-3).
Section 25.0 “Op amp/
Comparator Module”
Updated the Op amp/Comparator I/O Operating Modes Diagram (see Figure 25-1).
Updated the User-programmable Blanking Function Block Diagram (see Figure 25-3).
Updated the Digital Filter Interconnect Block Diagram (see Figure 25-4).
Added Section 25.1 “Op amp Application Considerations”.
Added Note 2 to the Comparator Control Register (see Register 25-2).
Updated the bit definitions in the Comparator Mask Gating Control Register (see
Register 25-5).
Section 27.0 “Special
Features”
Updated the FICD Configuration Register, updated Note 1, and added Note 3 in the
Configuration Byte Register Map (see Table 27-1).
Added Section 27.2 “User ID Words”.
Section 30.0 “Electrical
Characteristics”
Updated the following Absolute Maximum Ratings:
• Maximum current out of VSS pin
• Maximum current into VDD pin
Added Note 1 to the Operating MIPS vs. Voltage (see Table 30-1).
Updated all Idle Current (IIDLE) Typical and Maximum DC Characteristics values (see
Table 30-7).
Updated all Doze Current (IDOZE) Typical and Maximum DC Characteristics values
(see Table 30-9).
Added Note 2, removed parameter CM24, updated the Typical values parameters
CM10, CM20, CM21, CM32, CM41, CM44, and CM45, and updated the Minimum
values for CM40 and CM41, and the Maximum value for CM40 in the AC/DC
Characteristics: Op amp/Comparator (see Table 30-14).
Updated Note 2 and the Typical value for parameter VR310 in the Op amp/
Comparator Reference Voltage Settling Time Specifications (see Table 30-15).
Added Note 1, removed parameter VRD312, and added parameter VRD314 to the
Op amp/Comparator Voltage Reference DC Specifications (see Table 30-16).
Updated the Minimum, Typical, and Maximum values for Internal LPRC Accuracy
(see Table 30-22).
Updated the Minimum, Typical, and Maximum values for parameter SY37 in the
Reset, Watchdog Timer, Oscillator Start-up Timer, Power-up Timer Timing
Requirements (see Table 30-24).
The Maximum Data Rate values were updated for the SPI2 Maximum Data/Clock
Rate Summary (see Table 30-35)
DS70657E-page 494
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE A-2:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Section 30.0 “Electrical
Characteristics”
(Continued)
Update Description
These SPI2 Timing Requirements were updated:
• Maximum value for parameter SP10 and the minimum clock period value for
SCKx in Note 3 (see Table 30-36, Table 30-37, and Table 30-38)
• Maximum value for parameter SP70 and the minimum clock period value for
SCKx in Note 3 (see Table 30-40 and Table 30-42)
• The Maximum Data Rate values were updated for the SPI2 Maximum Data/Clock
Rate Summary (see Table 30-43)
These SPI1 Timing Requirements were updated:
• Maximum value for parameters SP10 and the minimum clock period value for
SCKx in Note 3 (see Table 30-44, Table 30-45, and Table 30-46)
• Maximum value for parameters SP70 and the minimum clock period value for
SCKx in Note 3 (see Table 30-47 through Table 30-50)
• Minimum value for parameters SP40 and SP41 see Table 30-44 through
Table 30-50)
Updated all Typical values for the CTMU Current Source Specifications (see
Table 30-55).
Updated Note1, the Maximum value for parameter AD06, the Minimum value for
AD07, and the Typical values for AD09 in the ADC Module Specifications (see
Table 30-56).
Added Note 1 to the ADC Module Specifications (12-bit Mode) (see Table 30-57).
Added Note 1 to the ADC Module Specifications (10-bit Mode) (see Table 30-58).
Updated the Minimum and Maximum values for parameter AD21b in the 10-bit Mode
ADC Module Specifications (see Table 30-58).
Updated Note 2 in the ADC Conversion (12-bit Mode) Timing Requirements (see
Table 30-59).
Updated Note 1 in the ADC Conversion (10-bit Mode) Timing Requirements (see
Table 30-60).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 495
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Revision D (December 2011)
This revision includes typographical and formatting
changes throughout the data sheet text.
All other major changes are referenced by their
respective section in Table A-3.
TABLE A-3:
MAJOR SECTION UPDATES
Section Name
Update Description
“16-bit Microcontrollers
and Digital Signal
Controllers (up to 512 KB
Flash and 48 KB SRAM)
with High-Speed PWM, Op
amps, and Advanced
Analog”
Removed the Analog Comparators column and updated the Op amps/Comparators
column in Table 1 and Table 2.
Section 21.0 “Enhanced
CAN (ECAN™) Module
(dsPIC33EPXXXGP/MC50X
Devices Only)”
Updated the CANCKS bit value definitions in CiCTRL1: ECAN Control Register 1
(see Register 21-1).
Section 30.0 “Electrical
Characteristics”
Updated the VBOR specifications and/or its related note in the following electrical
characteristics tables:
•
•
•
•
•
•
•
•
•
•
•
DS70657E-page 496
Table 30-1
Table 30-4
Table 30-12
Table 30-14
Table 30-15
Table 30-16
Table 30-56
Table 30-57
Table 30-58
Table 30-59
Table 30-60
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
Revision E (April 2012)
This revision includes typographical and formatting
changes throughout the data sheet text.
All other major changes are referenced by their
respective section in Table A-3.
TABLE A-4:
MAJOR SECTION UPDATES
Section Name
“16-bit Microcontrollers
and Digital Signal
Controllers (up to 512 KB
Flash and 48 KB SRAM)
with High-Speed PWM, Op
amps, and Advanced
Analog”
Update Description
The following 512 KB devices were added to the General Purpose Families table (see
Table 1):
• PIC24EP512GP202
• PIC24EP512GP204
• PIC24EP512GP206
• dsPIC33EP512GP502
• dsPIC33EP512GP504
• dsPIC33EP512GP506
The following 512 KB devices were added to the Motor Control Families table (see
Table 2):
• PIC24EP512MC202
• PIC24EP512MC204
• PIC24EP512MC206
• dsPIC33EP512MC202
• dsPIC33EP512MC204
• dsPIC33EP512MC206
• dsPIC33EP512MC502
• dsPIC33EP512MC504
• dsPIC33EP512MC506
Certain Pin Diagrams were updated to include the new 512 KB devices.
Section 4.0 “Memory
Organization”
Added a Program Memory Map for the new 512 KB devices (see Figure 4-4).
Added a Data Memory Map for the new dsPIC 512 KB devices (see Figure 4-11).
Added a Data Memory Map for the new PIC24 512 KB devices (see Figure 4-16).
Section 7.0 “Interrupt
Controller”
Updated the VECNUM bits in the INTTREG register (see Register 7-7).
Section 11.0 “I/O Ports”
Added tip 6 to Section 11.5 “I/O Helpful Tips”.
Section 27.0 “Special
Features”
The following modifications were made to the Configuration Byte Register Map (see
Table 27-1):
• Added the column Device Memory Size (KB)
• Removed Notes 1 through 4
• Added addresses for the new 512 KB devices
Section 30.0 “Electrical
Characteristics”
Updated the Minimum value for parameter DC10 (see Table 30-4).
Added Power-Down Current (Ipd) parameters for the new 512 KB devices (see
Table 30-8).
Updated the Minimum value for parameter CM34 (see Table 30-52).
Updated the Minimum and Maximum values and the Conditions for paramteer SY12
(see Table 30-21).
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 497
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 498
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
INDEX
A
Sources .................................................................... 152
AC Characteristics ............................................................ 410
Capacitive Loading Requirements on Output Pins ... 410
Internal FRC Accuracy.............................................. 412
Internal RC Accuracy ................................................ 412
Load Conditions ........................................................ 410
ADC
Initialization ............................................................... 319
Key Features............................................................. 319
Analog-to-Digital Converter (ADC).................................... 319
Arithmetic Logic Unit (ALU)................................................. 42
Assembler
MPASM Assembler................................................... 394
B
Bit-Reversed Addressing
Example .................................................................... 113
Implementation ......................................................... 112
Sequence Table (16-Entry)....................................... 113
Bit-Reversed Addressing (dsPIC33EPXXXMC20X/50X
and dsPIC33EPXXXGP50X Devices Only) .............. 112
Block Diagrams
16-bit Timer1 Module ................................................ 203
ADC Conversion Clock Period.................................. 321
ADC1 and ADC2 Module .......................................... 320
Comparator I/O Operating Modes............................. 351
Comparator Voltage Reference ................................ 352
Connections for On-Chip Voltage Regulator............. 380
CPU Core.................................................................... 34
CRC Module ............................................................. 369
CRC Shift Engine...................................................... 369
CTMU Configurations
Time Measurement ........................................... 313
Digital Filter Interconnect .......................................... 353
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X,
and PIC24EPXXXGP/MC20X............................. 23
ECAN Module ........................................................... 288
Input Capture ............................................................ 213
Oscillator System Diagram ....................................... 151
Output Compare ....................................................... 219
PLL............................................................................ 152
Quadrature Encoder Interface .................................. 250
Reset System............................................................ 121
Shared Port Structure ............................................... 171
SPIx module.............................................................. 266
Type B (Timer2 and Timer4)..................................... 208
Type C (Timer3 and Timer5)..................................... 208
UART ........................................................................ 281
User Programmable Blanking Function .................... 352
Watchdog Timer (WDT) ............................................ 381
C
C Compilers
MPLAB C18 .............................................................. 394
Charge Time Measurement Unit. See CTMU.
Code Examples
Port Write/Read ........................................................ 172
PWRSAV Instruction Syntax..................................... 161
Code Protection ........................................................ 375, 382
Configuring Analog Port Pins ............................................ 172
CPU
Control Register .......................................................... 38
CPU Clocking System....................................................... 152
© 2011-2012 Microchip Technology Inc.
CRC
User Interface ........................................................... 370
Data .................................................................. 370
CTMU Module
Register Map .............................................................. 95
Customer Change Notification Service............................. 505
Customer Notification Service .......................................... 505
Customer Support............................................................. 505
D
Data Address Space........................................................... 49
Alignment.................................................................... 49
Memory Map for dsPIC33EP128MC20X/50X
and dsPIC33EP128GP50X Devices................... 52
Memory Map for dsPIC33EP256MC20X/50X
and dsPIC33EP256GP50X Devices................... 53
Memory Map for dsPIC33EP32MC20X/50X
and dsPIC33EP32GP50X Devices..................... 50
Memory Map for dsPIC33EP512MC20X/50X
and dsPIC33EP512GP50X Devices................... 54
Memory Map for dsPIC33EP64MC20X/50X
and dsPIC33EP64GP50X Devices..................... 51
Memory Map for
PIC24EP128GP/MC20X/50X Devices ............... 57
Memory Map for
PIC24EP256GP/MC20X/50X Devices ............... 58
Memory Map for
PIC24EP32GP/MC20X/50X Devices ................. 55
Memory Map for
PIC24EP512GP/MC20X/50X Devices ............... 59
Memory Map for
PIC24EP64GP/MC20X/50X Devices ................. 56
Near Data Space ........................................................ 49
SFR ............................................................................ 49
Width .......................................................................... 49
DC and AC Characteristics
Graphs and Tables ................................................... 463
DC Characteristics............................................................ 398
BOR.......................................................................... 408
I/O Pin Input Specifications ...................................... 405
I/O Pin Output Specifications............................ 408, 452
Idle Current (IDOZE) .................................................. 404
Idle Current (IIDLE) .................................................... 401
Internal Voltage Regulator........................................ 399
Operating Current (IDD) ............................................ 400
Power-Down Current (IPD)........................................ 402
Program Memory...................................................... 409
Temperature and Voltage Specifications.................. 399
Development Support ....................................................... 393
DMA Module
DSADR register ........................................................ 145
supported peripherals............................................... 137
DMAC Registers ............................................................... 139
DMAxCNT ................................................................ 139
DMAxCON................................................................ 139
DMAxPAD ................................................................ 139
DMAxREQ ................................................................ 139
DMAxSTA................................................................. 139
DMAxSTB................................................................. 139
Doze Mode ....................................................................... 163
DSP Engine ........................................................................ 42
Preliminary
DS70657E-page 499
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
E
ECAN Module
CiBUFPNT1 register ................................................. 299
CiBUFPNT2 register ................................................. 300
CiBUFPNT3 register ................................................. 300
CiBUFPNT4 register ................................................. 301
CiCFG1 register ........................................................ 297
CiCFG2 register ........................................................ 298
CiCTRL1 register ...................................................... 290
CiCTRL2 register ...................................................... 291
CiEC register............................................................. 297
CiFCTRL register ...................................................... 293
CiFEN1 register ........................................................ 299
CiFIFO register ......................................................... 294
CiFMSKSEL1 register ............................................... 303
CiFMSKSEL2 register ............................................... 304
CiINTE register ......................................................... 296
CiINTF register.......................................................... 295
CiRXFnEID register .................................................. 303
CiRXFnSID register .................................................. 302
CiRXFUL1 register .................................................... 306
CiRXFUL2 register .................................................... 306
CiRXMnEID register.................................................. 305
CiRXMnSID register.................................................. 305
CiRXOVF1 register ................................................... 307
CiRXOVF2 register ................................................... 307
CiTRmnCON register ................................................ 308
CiVEC register .......................................................... 292
Modes of Operation .................................................. 289
Overview ................................................................... 287
ECAN Registers
Acceptance Filter Enable Register (CiFEN1)............ 299
Acceptance Filter Extended Identifier Register n
(CiRXFnEID) ..................................................... 303
Acceptance Filter Mask Extended Identifier Register n
(CiRXMnEID) .................................................... 305
Acceptance Filter Mask Standard Identifier Register n
(CiRXMnSID) .................................................... 305
Acceptance Filter Standard Identifier Register n
(CiRXFnSID) ..................................................... 302
Baud Rate Configuration Register 1 (CiCFG1) ......... 297
Baud Rate Configuration Register 2 (CiCFG2) ......... 298
Control Register 1 (CiCTRL1) ................................... 290
Control Register 2 (CiCTRL2) ................................... 291
FIFO Control Register (CiFCTRL) ............................ 293
FIFO Status Register (CiFIFO) ................................. 294
Filter 0-3 Buffer Pointer Register (CiBUFPNT1) ....... 299
Filter 12-15 Buffer Pointer Register (CiBUFPNT4) ... 301
Filter 15-8 Mask Selection Register (CiFMSKSEL2). 304
Filter 4-7 Buffer Pointer Register (CiBUFPNT2) ....... 300
Filter 7-0 Mask Selection Register (CiFMSKSEL1)... 303
Filter 8-11 Buffer Pointer Register (CiBUFPNT3) ..... 300
Interrupt Code Register (CiVEC) .............................. 292
Interrupt Enable Register (CiINTE) ........................... 296
Interrupt Flag Register (CiINTF) ............................... 295
Receive Buffer Full Register 1 (CiRXFUL1).............. 306
Receive Buffer Full Register 2 (CiRXFUL2).............. 306
Receive Buffer Overflow Register 2 (CiRXOVF2)..... 307
Receive Overflow Register (CiRXOVF1) .................. 307
ECAN Transmit/Receive Error Count Register (CiEC) ..... 297
ECAN TX/RX Buffer m Control Register (CiTRmnCON) .. 308
Electrical Characteristics................................................... 397
AC ............................................................................. 410
Enhanced CAN Module..................................................... 287
Equations
DS70657E-page 500
Device Operating Frequency .................................... 152
Errata .................................................................................. 20
F
Flash Program Memory .................................................... 117
Control Registers ...................................................... 118
Operations ................................................................ 118
Programming Algorithm ............................................ 120
RTSP Operation ....................................................... 118
Table Instructions ..................................................... 117
Flexible Configuration ....................................................... 375
H
High-Speed PWM ............................................................. 225
I
I/O Ports............................................................................ 171
Parallel I/O (PIO) ...................................................... 171
Write/Read Timing .................................................... 172
In-Circuit Debugger........................................................... 382
In-Circuit Emulation .......................................................... 375
In-Circuit Serial Programming (ICSP)....................... 375, 382
Input Capture .................................................................... 213
Registers .................................................................. 215
Input Change Notification ................................................. 172
Instruction Addressing Modes .......................................... 109
File Register Instructions .......................................... 109
Fundamental Modes Supported ............................... 110
MAC Instructions (dsPIC33EPXXXMC20X/50X and
dsPIC33EPXXXGP50X Devices Only)............. 110
MCU Instructions ...................................................... 109
Move and Accumulator Instructions.......................... 110
Other Instructions ..................................................... 110
Instruction Set
Overview................................................................... 386
Summary .................................................................. 383
Instruction-Based Power-Saving Modes........................... 161
Idle ............................................................................ 162
Sleep ........................................................................ 162
Internal RC Oscillator
Use with WDT........................................................... 381
Internet Address ............................................................... 505
Interrupt Control and Status Registers ............................. 129
IFSx .......................................................................... 129
INTCON1 .................................................................. 129
INTCON2 .................................................................. 129
Interrupt Vector Table (IVT) .............................................. 125
Interrupts Coincident with Power Save Instructions ......... 162
J
JTAG Boundary Scan Interface ........................................ 375
JTAG Interface.................................................................. 382
M
Memory Organization ......................................................... 43
Microchip Internet Web Site.............................................. 505
Modulo Addressing
Applicability............................................................... 112
Operation Example ................................................... 111
Start and End Address ............................................. 111
W Address Register Selection .................................. 111
Modulo Addressing (dsPIC33EPXXXMC20X/50X and
dsPIC33EPXXXGP50X Devices Only) ..................... 111
Most Recent RAM Address Low Register ........................ 145
Most Recent RAM High Address ...................................... 145
MPLAB ASM30 Assembler, Linker, Librarian ................... 394
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
MPLAB Integrated Development Environment Software .. 393
MPLAB PM3 Device Programmer .................................... 396
MPLAB REAL ICE In-Circuit Emulator System................. 395
MPLINK Object Linker/MPLIB Object Librarian ................ 394
O
Open-Drain Configuration ................................................. 172
Output Compare ............................................................... 219
P
Packaging ......................................................................... 467
Details ....................................................................... 489
Marking ............................................................. 467, 469
Peripheral Module Disable (PMD) .................................... 163
Peripheral Trigger Generator (PTG) Module .................... 333
Peripherals supported by DMA ......................................... 137
Pinout I/O Descriptions (table) ............................................ 24
Power-Saving Features .................................................... 161
Clock Frequency and Switching................................ 161
Program Address Space ..................................................... 43
Construction.............................................................. 114
Data Access from Program Memory Using
Table Instructions ............................................. 115
Data Access from, Address Generation.................... 114
Memory Map ....................................... 43, 44, 45, 46, 47
Table Read Instructions
TBLRDH ........................................................... 115
TBLRDL ............................................................ 115
Program Memory
Organization................................................................ 48
Reset Vector ............................................................... 48
Programmable CRC
Special Function Registers ......................................... 87
Programmer’s Model........................................................... 34
Register Description.................................................... 35
PTG
Introduction ............................................................... 333
Q
Quadrature Encoder Interface (QEI) ................................. 249
R
Reader Response ............................................................. 506
Register
PTG Adjust (PTGADJ) .............................................. 344
PTG Literal (PTGL0) ................................................. 344
PTG Step Queue Pointer (PTGQPTR) ..................... 345
PTG Step Queue Pointer Register 0 (PTGQUE0) .... 345
Register Maps
ADC1 and ADC2......................................................... 83
Comparator ................................................................. 95
CPU Core (dsPIC33EPXXXMC20X/50X and
PIC24EPXXXMC20X Devices Only) ................. 61
CPU Core (PIC24EPXXXGP/MC20X Devices Only).. 63
CPU Core for dsPIC33EPXXXGP50X and
PIC24EPXXXGP20X Devices Only ................... 63
DMAC ......................................................................... 96
ECAN1 (When WIN (C1CTRL) = 0 or 1)
dsPIC33EPXXXMC/GP50X Devices Only.......... 84
ECAN1 (When WIN (C1CTRL) = 0)
dsPIC33EPXXXMC/GP50X Devices Only.......... 84
ECAN1 (WIN (C1CTRL) = 1)
dsPIC33EPXXXMC/GP50X Devices Only.......... 85
I2C1 and I2C2............................................................. 81
Input Capture 1 through Input Capture 16 .................. 75
Interrupt Controller
© 2011-2012 Microchip Technology Inc.
Preliminary
(dsPIC33EPXXXGP50X Devices Only).............. 68
Interrupt Controller
(dsPIC33EPXXXMC20X Devices Only) ............. 70
Interrupt Controller
(dsPIC33EPXXXMC50X Devices Only) ............. 72
Interrupt Controller
(PIC24EPXXXGP20X Devices Only) ................. 64
Interrupt Controller
(PIC24EPXXXMC20X Devices Only) ................. 66
Output Compare 1 through Output Compare 16 ........ 76
Peripheral Pin Select Input
(dsPIC33EPXXXGP50X Devices Only).............. 90
Peripheral Pin Select Input
(dsPIC33EPXXXMC20X Devices Only) ............. 91
Peripheral Pin Select Input
(dsPIC33EPXXXMC50X Devices Only) ............. 90
Peripheral Pin Select Input
(PIC24EPXXXGP20X Devices Only) ................. 89
Peripheral Pin Select Input
(PIC24EPXXXMC20X Devices Only) ................. 89
Peripheral Pin Select Output
(dsPIC33EPXXXGP/MC202/502 and
PIC24EPXXXGP/MC202 Devices Only) ............ 87
Peripheral Pin Select Output
(dsPIC33EPXXXGP/MC203/503 and
PIC24EPXXXGP/MC203 Devices Only) ............ 87
Peripheral Pin Select Output
(dsPIC33EPXXXGP/MC204/504 and
PIC24EPXXXGP/MC204 Devices Only) ............ 88
Peripheral Pin Select Output
(dsPIC33EPXXXGP/MC206/506 and
PIC24EPXXGP/MC206 Devices Only)............... 88
PMD (dsPIC33EPXXXMC50X Devices Only) ............ 94
PMD (PIC24EPXXXGP20X Devices Only) ................ 93
PORTA
(PIC24EPXXXGP/MC202 and
dsPIC33EPXXXGP/MC202/502 Devices Only) 102
PORTA
(PIC24EPXXXGP/MC203 and
dsPIC33EPXXXGP/MC203/503 Devices Only) 101
PORTA
(PIC24EPXXXGP/MC204 and
dsPIC33EPXXXGP/MC204/504 Devices Only) 100
PORTA
(PIC24EPXXXGP/MC206 and
dsPIC33EPXXXGP/MC206/506 Devices Only).. 97
PORTB
(PIC24EPXXXGP/MC202 and
dsPIC33EPXXXGP/MC202/502 ....................... 102
PORTB
(PIC24EPXXXGP/MC203 and
dsPIC33EPXXXGP/MC203/503 Devices Only) 101
PORTB
(PIC24EPXXXGP/MC204 and
dsPIC33EPXXXGP/MC204/504 Devices Only. 100
PORTB
(PIC24EPXXXGP/MC206
and dsPIC33EPXXXGP/MC206/506 Devices Only)
97
PORTC
(PIC23EPXXXGP/MC203 and
dsPIC33EPXXXGP/MC203/503 Devices Only) 101
PORTC
(PIC24EPXXXGP/MC204 and
dsPIC33EPXXXGP/MC204/504 Devices Only) 100
DS70657E-page 501
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
PORTC
(PIC24EPXXXGP/MC206 and
dsPIC33EPXXXGP/MC206/506 Devices Only) .. 97
PORTD
(PIC24EPXXXGP/MC206 and
dsPIC33EPXXXGP/MC206/506 Devices Only) .. 98
PORTE
(PIC24EPXXXGP/MC206 and
dsPIC33EPXXXGP/MC206/506 Devices Only) .. 98
PORTF
(PIC24EPXXXGP/MC206 and
dsPIC33EPXXXGP/MC206/506 Devices Only) .. 98
PORTG
(PIC24EPXXXGP/MC206 and
dsPIC33EPXXXGP/MC206/506 Devices Only) .. 99
PWM
(dsPIC33EPXXXMC20X/50X and
PIC24EPXXXMC20X Devices Only)................... 78
PWM Generator 1
(dsPIC33EPXXXMC20X/50X and
PIC24EPXXXMC20X Devices Only)................... 78
PWM Generator 2
(dsPIC33EPXXXMC20X/50X and
PIC24EPXXXMC20X Devices Only)................... 79
PWM Generator 3
(dsPIC33EPXXXMC20X/50X and
PIC24EPXXXMC20X Devices Only)................... 79
QEI1 Register Map
(dsPIC33EPXXXMC20X/50X and
PIC24EPXXXMC20X Devices Only)................... 80
Reference Clock ......................................................... 92
SPI1, SPI2, SPI3, and SPI4 ........................................ 82
System Control ........................................................... 92
Timer1 through Timer9 ............................................... 74
UART1, UART2, UART3, and UART4 ........................ 81
Registers
AD1CHS0 (ADC1 Input Channel 0 Select) ............... 329
AD1CHS123 (ADC1 Input Channel 1, 2, 3 Select) ... 328
AD1CON1 (ADC1 Control 1) .................................... 323
AD1CON2 (ADC1 Control 2) .................................... 325
AD1CON3 (ADC1 Control 3) .................................... 326
AD1CON4 (ADC1 Control 4) .................................... 327
AD1CSSH (ADC1 Input Scan Select High) .............. 331
AD1CSSL (ADC1 Input Scan Select Low) ................ 332
ALTDTRx (PWM Alternate Dead-Time) .................... 238
AUXCONx (PWM Auxiliary Control).......................... 247
CHOP (PWM Chop Clock Generator)....................... 234
CiBUFPNT1 (ECAN Filter 0-3 Buffer Pointer)........... 299
CiBUFPNT2 (ECAN Filter 4-7 Buffer Pointer)........... 300
CiBUFPNT3 (ECAN Filter 8-11 Buffer Pointer)......... 300
CiBUFPNT4 (ECAN Filter 12-15 Buffer Pointer)....... 301
CiCFG1 (ECAN Baud Rate Configuration 1) ............ 297
CiCFG2 (ECAN Baud Rate Configuration 2) ............ 298
CiCTRL1 (ECAN Control 1) ...................................... 290
CiCTRL2 (ECAN Control 2) ...................................... 291
CiEC (ECAN Transmit/Receive Error Count)............ 297
CiFCTRL (ECAN FIFO Control) ................................ 293
CiFEN1 (ECAN Acceptance Filter Enable) ............... 299
CiFIFO (ECAN FIFO Status)..................................... 294
CiFMSKSEL1 (ECAN Filter 7-0 Mask Selection) ...... 303
CiFMSKSEL2 (ECAN Filter 15-8 Mask Selection) .... 304
CiINTE (ECAN Interrupt Enable) .............................. 296
CiINTF (ECAN Interrupt Flag) ................................... 295
CiRXFnEID (ECAN Acceptance Filter n
Extended Identifier)........................................... 303
DS70657E-page 502
Preliminary
CiRXFnSID (ECAN Acceptance Filter n
Standard Identifier) ........................................... 302
CiRXFUL1 (ECAN Receive Buffer Full 1)................. 306
CiRXFUL2 (ECAN Receive Buffer Full 2)................. 306
CiRXMnEID (ECAN Acceptance Filter Mask n
Extended Identifier) .......................................... 305
CiRXMnSID (ECAN Acceptance Filter Mask n
Standard Identifier) ........................................... 305
CiRXOVF1 (ECAN Receive Buffer Overflow 1)........ 307
CiRXOVF2 (ECAN Receive Buffer Overflow 2)........ 307
CiTRBnSID (ECAN Buffer n Standard Identifier)..... 309,
310, 312
CiTRmnCON (ECAN TX/RX Buffer m Control) ........ 308
CiVEC (ECAN Interrupt Code).................................. 292
CLKDIV (Clock Divisor) ............................................ 156
CM4CON (Comparator Control 4) ............................ 361
CMSTAT (Comparator Status) ................................. 357
CMxCON (Comparator Control 1-3) ......................... 359
CMxFLTR (Comparator Filter Control) ..................... 367
CMxMSKCON (Comparator Mask Gating Control) .. 365
CMxMSKSRC (Comparator Mask Source Control) .. 363
CORCON (Core Control) .................................... 40, 131
CTMUCON (CTMU Control) ............................. 315, 316
CTMUCON1 (CTMU Control Register 1).................. 315
CTMUCON1 (CTMU Control Register 2).................. 316
CTMUICON (CTMU Current Control) ....................... 317
CVRCON (Comparator Voltage Reference Control) 368
DEVID (Device ID).................................................... 379
DEVREV (Device Revision)...................................... 379
DTRx (PWM Dead-Time).......................................... 238
FCLCONx (PWM Fault Current-Limit Control).......... 243
I2CxCON (I2Cx Control) ........................................... 276
I2CxMSK (I2Cx Slave Mode Address Mask) ............ 280
I2CxSTAT (I2Cx Status) ........................................... 278
ICxCON1 (Input Capture x Control 1)....................... 215
ICxCON2 (Input Capture x Control 2)....................... 216
IDNXxCNTH (Index Counter High Word) ................. 259
INDXxCNTL (Index Counter Low Word)................... 259
INDXxHLD (Index Counter Hold).............................. 260
INTCON1 (Interrupt Control 1).................................. 132
INTCON2 (Interrupt Control 2).................................. 134
INTCON2 (Interrupt Control 3).................................. 135
INTCON4 (Interrupt Control 4).................................. 135
INTTREG Interrupt Control and Status Register ...... 136
INTxHLDH (Interval Timer Hold High Word)............. 263
INTxHLDL (Interval Timer Hold Low Word) .............. 263
INTxTMRH (Interval Timer High Word) .................... 262
INTxTMRL (INterval Timer Low Word) ..................... 263
IOCONx (PWM I/O Control)...................................... 240
LEBCONx (Leading-Edge Blanking Control) ............ 245
LEBDLYx (Leading-Edge Blanking Delay) ............... 246
MDC (PWM Master Duty Cycle) ............................... 234
NVMCOM (Flash Memory Control)........................... 120
NVMCON (Non-volatile (NVM) Memory Control) ..... 119
NVMKEY (Non-volatile Memory Key) ....................... 120
OCxCON1 (Output Compare x Control 1) ................ 221
OCxCON2 (Output Compare x Control 2) ................ 223
OSCCON (Oscillator Control) ................................... 154
OSCTUN (FRC Oscillator Tuning)............................ 159
PDCx (PWM Generator Duty Cycle)......................... 237
PHASEx (PWM Primary Phase Shift)....................... 237
PLLFBD (PLL Feedback Divisor).............................. 158
PMD1 (Peripheral Module Disable Control 1)........... 164
PMD2 (Peripheral Module Disable Control 2)........... 166
PMD3 (Peripheral Module Disable Control 3)........... 167
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
PMD4 (Peripheral Module Disable Control 4)........... 167
PMD6 (Peripheral Module Disable Control 6)........... 168
PMD7 (Peripheral Module Disable Control 7)........... 169
POSxCNTH (Position Counter High Word)............... 258
POSxCNTL (Position Counter Low Word) ................ 258
POSxHLD (Position Counter Hold) ........................... 258
PTCON (PWM Time Base Control) .......................... 230
PTCON2 (Primary Master Clock Divider Select) ...... 232
PTG Broadcast Trigger Enable (PTGBTE) ............... 339
PTG Control (PTGCON) ........................................... 338
PTG Control/Status (PTGCST)................................. 336
PTG Counter 0 Limit (PTGC0LIM)............................ 342
PTG Counter 1 Limit (PTGC1LIM)............................ 343
PTG Hold (PTGHOLD) ............................................. 343
PTG Step Delay Limit (PTGSDLIM).......................... 342
PTG Timer0 Limit (PTGT0LIM)................................. 341
PTG Timer1 Limit (PTGT1LIM)................................. 341
PTPER (Primary Master Time Base Period)............. 233
PWMCONx (PWM Control)....................................... 235
QEI1CON (QEI Control)............................................ 252
QEI1GECH (Greater Than or Equal Compare
High Word)........................................................ 262
QEI1GECL (Greater Than or Equal Compare
Low Word) ........................................................ 262
QEI1ICH (Initialization/Capture High Word).............. 260
QEI1ICL (Initialization/Capture Low Word) ............... 260
QEI1IOC (QEI I/O Control) ....................................... 254
QEI1LECH (Less Than or Equal Compare
High Word)........................................................ 261
QEI1LECL (Less Than or Equal Compare
Low Word) ........................................................ 261
QEI1STAT (QEI Status)............................................ 256
RCON (Reset Control) .............................................. 123
REFOCON (Reference Oscillator Control) ............... 160
RPINR0 (Peripheral Pin Select Input 0).................... 180
RPINR1 (Peripheral Pin Select Input 1).................... 181
RPINR11 (Peripheral Pin Select Input 11)................ 185
RPINR12 (Peripheral Pin Select Input 12)................ 186
RPINR14 (Peripheral Pin Select Input 14)................ 187
RPINR15 (Peripheral Pin Select Input 15)................ 188
RPINR18 (Peripheral Pin Select Input 18)................ 189
RPINR19 (Peripheral Pin Select Input 19)................ 190
RPINR20 (Peripheral Pin Select Input 20)................ 191
RPINR23 (Peripheral Pin Select Input 23)................ 192
RPINR26 (Peripheral Pin Select Input 26)................ 193
RPINR3 (Peripheral Pin Select Input 3).................... 182
RPINR37 (Peripheral Pin Select Input 37)................ 194
RPINR38 (Peripheral Pin Select Input 38)................ 195
RPINR40 (Peripheral Pin Select Input 40)................ 196
RPINR7 (Peripheral Pin Select Input 7).................... 183
RPINR8 (Peripheral Pin Select Input 8).................... 184
RPOR0 (Peripheral Pin Select Output 0).................. 197
RPOR1 (Peripheral Pin Select Output 1).................. 197
RPOR2 (Peripheral Pin Select Output 2).................. 198
RPOR3 (Peripheral Pin Select Output 3).................. 198
RPOR4 (Peripheral Pin Select Output 4).................. 199
RPOR5 (Peripheral Pin Select Output 5).................. 199
RPOR6 (Peripheral Pin Select Output 6).................. 200
RPOR7 (Peripheral Pin Select Output 7).................. 200
RPOR8 (Peripheral Pin Select Output 8).................. 201
RPOR9 (Peripheral Pin Select Output 9).................. 201
SEVTCMP (Primary Special Event Compare) .......... 233
SPIxCON1 (SPIx Control 1)...................................... 270
SPIxCON2 (SPIx Control 2)...................................... 271
SPIxSTAT (SPIx Status and Control) ....................... 268
© 2011-2012 Microchip Technology Inc.
SR (CPU Status) ................................................ 38, 130
T1CON (Timer1 Control) .......................................... 205
TRGCONx (PWM Trigger Control) ........................... 239
TRIGx (PWM Primary Trigger Compare Value) ....... 242
TxCON (T2CON or T4CON Control) ........................ 210
TyCON (T3CON or T5CON Control) ........................ 211
UxMODE (UARTx Mode) ......................................... 283
UxSTA (UARTx Status and Control) ........................ 285
VELxCNT (Velocity Counter).................................... 259
Reset
Illegal Opcode........................................................... 121
Uninitialized W Register ........................................... 121
Reset Sequence ............................................................... 125
Resets .............................................................................. 121
Resources Required for Digital PFC............................. 30, 32
S
Serial Peripheral Interface (SPI) ....................................... 265
Software Simulator (MPLAB SIM) .................................... 395
Software Stack Pointer, Frame Pointer
CALLL Stack Frame ................................................. 109
Special Features of the CPU ............................................ 375
Symbols Used in Opcode Descriptions ............................ 384
T
Temperature and Voltage Specifications
AC............................................................................. 410
Timer1 .............................................................................. 203
Timer2/3 and Timer4/5 ..................................................... 207
Timing Characteristics
CLKO and I/O ........................................................... 413
Timing Diagrams
10-bit ADC Conversion (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 0,
SSRC<3:0> = 000) ........................................... 461
10-bit ADC Conversion (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 1,
SSRC<2:0> = 111,
SAMC<4:0> = 00001)....................................... 461
10-bit ADC Conversion (CHPS<1:0> = 01,
SIMSAM = 0, ASAM = 1, SSRC<3:0> = 111,
SAMC<4:0> = 00010)....................................... 461
12-bit ADC Conversion
(ASAM = 0, SSRC<3:0> = 000)........................ 459
ECAN I/O.................................................................. 451
External Clock .......................................................... 411
I2Cx Bus Data (Master Mode) .................................. 447
I2Cx Bus Data (Slave Mode) .................................... 449
I2Cx Bus Start/Stop Bits (Master Mode)................... 447
I2Cx Bus Start/Stop Bits (Slave Mode)..................... 449
Input Capture (CAPx) ............................................... 417
Motor Control PWM .................................................. 419
Motor Control PWM Fault ......................................... 419
OC/PWM .................................................................. 418
Output Compare (OCx) ............................................ 417
QEA/QEB Input ........................................................ 421
QEI Module Index Pulse........................................... 422
Timer1, 2, 3 External Clock .............................. 413, 415
TimerQ (QEI Module) External Clock ....................... 420
Timing Requirements
CLKO and I/O ........................................................... 413
DCI AC-Link Mode.................................................... 461
DCI Multi-Channel, I2S Modes ................................. 461
DMA Module............................................................. 462
External Clock .......................................................... 411
Timing Specifications
Preliminary
DS70657E-page 503
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
10-bit ADC Conversion Requirements ...................... 462
12-bit ADC Conversion Requirements ...................... 460
CAN I/O Requirements ............................................. 451
I2Cx Bus Data Requirements (Master Mode) ........... 448
I2Cx Bus Data Requirements (Slave Mode) ............. 450
Motor Control PWM Requirements ........................... 419
Output Compare Requirements ................................ 417
PLL Clock.................................................................. 412
QEI External Clock Requirements ............................ 420
QEI Index Pulse Requirements................................. 422
Quadrature Decoder Requirements .......................... 421
Reset, Watchdog Timer, Oscillator Start-up Timer,
Power-up Timer and Brown-out Reset
Requirements.................................................... 414
Simple OC/PWM Mode Requirements ..................... 418
Timer1 External Clock Requirements ....................... 415
Timer2 External Clock Requirements ....................... 416
Timer3 External Clock Requirements ....................... 416
U
Universal Asynchronous Receiver Transmitter (UART).... 281
V
Voltage Regulator (On-Chip)............................................. 380
W
Watchdog Timer (WDT) ............................................ 375, 381
Programming Considerations ................................... 381
WWW Address.................................................................. 505
WWW, On-Line Support...................................................... 20
DS70657E-page 504
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQs), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://microchip.com/support
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 505
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
Device: dsPIC33EPXXXGP50X,
PIC24EPXXXGP/MC20X
Questions:
N
dsPIC33EPXXXMC20X/50X,
and
Literature Number: DS70657E
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS70657E-page 506
Preliminary
© 2011-2012 Microchip Technology Inc.
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
dsPIC 33 EP 64 MC5 04 T I / PT - XXX
Examples:
dsPIC33EP64MC504-I/PT:
dsPIC33, Enhanced Performance,
64 KB program memory,
Motor Control, 44-pin,
Industrial temperature,
TQFP package.
Microchip Trademark
Architecture
Flash Memory Family
Program Memory Size (KB)
Product Group
Pin Count
Tape and Reel Flag (if applicable)
Temperature Range
Package
Pattern
Architecture:
33
24
=
=
16-bit Digital Signal Controller
16-bit Microcontroller
Flash Memory Family:
EP
=
Enhanced Performance
Product Group:
GP
MC
=
=
General Purpose family
Motor Control family
Pin Count:
02
03
04
06
=
=
=
=
28-pin
36-pin
44-pin
64-pin
Temperature Range:
I
E
=
=
-40° C to+85° C (Industrial)
-40° C to+125° C (Extended)
Package:
ML
MM
MR
PT
PT
SO
SP
SS
TL
TL
=
=
=
=
=
=
=
=
=
=
Plastic Quad, No Lead Package - (44-pin) 8x8 mm body (QFN)
Plastic Quad, No Lead Package - (28-pin) 6x6 mm body (QFN-S)
Plastic Quad, No Lead Package - (64-pin) 9x9 mm body (QFN)
Plastic Thin Quad Flatpack - (44-pin) 10x10 mm body (TQFP)
Plastic Thin Quad Flatpack - (64-pin) 10x10 mm body (TQFP)
Plastic Small Outline, Wide - (28-pin) 7.50 mil body (SOIC)
Skinny Plastic Dual In-Line - (28-pin) 300 mil body (SPDIP)
Plastic Shrink Small Outline - (28-pin) 5.30 mm body (SSOP)
Very Thin Leadless Array - (36-pin) 5x5 mm body (VTLA)
Very Thin Leadless Array - (44-pin) 6x6 mm body (VTLA)
© 2011-2012 Microchip Technology Inc.
Preliminary
DS70657E-page 507
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
NOTES:
DS70657E-page 508
Preliminary
© 2011-2012 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
PIC32 logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, chipKIT,
chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
MPLINK, mTouch, Omniscient Code Generation, PICC,
PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE,
rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2011-2012, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-62076-202-8
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
© 2011-2012 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
Preliminary
DS70657E-page 509
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-330-9305
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS70657E-page 510
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
11/29/11
Preliminary
© 2011-2012 Microchip Technology Inc.