[AK5371] ASAHI KASEI AK5371 2ch A/D Converter with USB I/F Features: General Description USB-IF Certified The AK5371 is stereo A/D converter with USB I/F. The AK5371 integrates USB serial interface engine, USB transceiver, audio class processing unit, endpoints, and high quality 2 channel AD converter into the chip. Incorporates USB Audio Controller USB Serial Interface Engine Audio Class Encoder/Decoder 2 Endpoints (FIFO) USB transceiver 16 bit A/D Converter 2 channels Mute/Volume Control A/D S/N: 84dBA (44.1kHz, Gain = 0dB) Low Power Dissipation Normal Operation: 26mA Suspend Mode: < 1uA Programmable Gain Amplifier (IPGA) +24dB to –31dB @1dB Step 20dB Pre-amplifier On-chip PLL 5 Sampling Frequencies support 8kHz, 11.025kHz 22.05kHz, 44.1kHz, 48kHz As the AK5371 incorporates PLL, it can support several sampling frequencies, 8kHz, 11.025kHz, 22.05kHz, 44.1kHz, and 48kHz with only one crystal. Moreover, the AK5371 integrates volume control, and mute function. Not only power consumption at normal operation is very low, but also the current at suspend mode is less than 1µA. The AK5371 includes 20dB fixed gain pre-amplifier. In addition to this, as the AK5371 also incorporates IPGA which can amplify the microphone signal up to +24dB, total gain is 44dB maximum. The AK5371 has EEPROM I/F for customizing Device Descriptor and String Descriptor. By connecting 1K bit, 2K bit, or 4Kbit MicrowireTM type EEPROM, the AK5371 can customize Vendor ID, Product ID in Device Descriptor, and String Descriptor. This device is good for not only business application such as conferencing but also games, voice recognition, and Karaoke. EEPROM I/F can customize Device Descriptor, and String Descriptor Related Documents For the detail of USB specification, and Audio Class, please refer to the following documents. Single Power Supply, Low Power +3.3±0.3 Volts Universal Serial Bus Specification Revision 1.1 Universal Serial Bus Device Class Definition for Audio Devices, Revision 1.0 Package 48pin LQFP MS0103-E-00 MS0103-E-00 2001/06 1 ASAHI KASEI [AK5371] Block Diagram microwire BGND BIASSEL VA VREF VCOM DGND AGND VD SUSN EEPROM (1K bit) CS SK EPAO MICBIAS MICR Config/String ROM Common Voltage VREF Mute & Volume control 20dB + Audio Class Decoder EndPoint0 OUT_FIFO Audio Class Encoder EndPoint0 IN_FIFO AMPR2I 20dB + EPEN Serial Interface Engine Testmode1,2,3 16bit ADC + EPDI EPSEL AMPR1O MICL EEPROM Control EndPoint1 IN_FIFO TEST SystemCLK AMPL1O AMPL2I adCLK + USB Transceiver PLL AMPR2O AMPL2O XTLIN DP DN XTLOUT RSTN LFLT2 LFLT1 CRYSTAL Ordering Guide AK5371VQ AKD5371 0 ∼ +70 °C 48pin LQFP (0.5mm pitch) Evaluation Board Pin Layout NC EPDI EPEN 45 1 EPSEL NC RSTN SUSN NC NC DP DN NC VD 40 NC DGND 35 CS NC TESTMODE3 TEST 5 NC XTALOUT XTALIN 30 VREF LFLT1 AGND 10 VA BIASSEL NC 15 25 20 NC AMPR2O AMPR2I AMPR1O MICR NC AMPL2O AMPL2I AMPL1O MICL MICBIAS VCOM NC MS0103-E-00 MS0103-E-00 TESTMODE1 NC TESTMODE2 LFLT2 EPAO SK BGND 2001/06 2 ASAHI KASEI [AK5371] Pin/Function No. 1 2 3 4 5 6 7 8 9 Signal Name VD DGND BGND NC TESTMODE3 XTALOUT XTALIN TESTMODE2 LFLT1 10 LFLT2 O A 11 BIASSEL I D 12 13 14 15 NC NC VCOM MICBIAS O O A A 16 17 18 19 20 21 22 23 24 MICL AMPL1O AMPL2I AMPL2O NC MICR AMPR1O AMPR2I AMPR2O I O I O I O I O A A A A A A A A MS0103-E-00 MS0103-E-00 I/O P P P I O I I O Ana / Dig D D D D A A A A Description Digital Power Supply, 3.3V Digital Ground,0V Bulk Ground, 0V No Connection Please tie down to AGND for normal operation. Crystal Oscillator Output, Connect Crystal Resonator Crystal Oscillator Input, Connect Crystal Resonator Please tie down to AGND for normal operation. adPLL loop filter Pin. Connect 51kΩ resistor and 8200pF capacitor in series externally. System clock PLL loop filter Pin. Connect 18kΩ resistor and 6800pF capacitor in series externally. MIC BIAS Select Pin Select MICBIAS Output "L": VA(through switch) “H”: VREF buffer output No Connection No Connection Analog Common Voltage Reference Pin Voltage Reference Output for the Microphone’s bias voltage When this chip goes into Suspend mode, this pin goes to Hi-Z. Left Channel Microphone Input Left Channel 1st Amplifier Output Pin Left Channel 2nd Amplifier Input Pin Left Channel 2nd Amplifier Output Pin No Connection Right Channel Microphone Input Right Channel 1st Amplifier Output Pin Right Channel 2nd Amplifier Input Pin Right Channel 2nd Amplifier Output Pin 2001/06 3 ASAHI KASEI [AK5371] No. 25 26 27 28 29 30 31 32 Signal Name NC VA AGND VREF NC TESTMODE1 NC TEST 33 CS 34 SK 35 EPAO O D EEPROM Address Output Pin 36 37 38 NC NC EPDI I D No Connection No Connection EEPROM Data Input Pin (This pin is internally pulled down) 39 EPEN I D 40 EPSEL I D 41 42 NC SUSN O D 43 RSTN I D 44 45 46 NC NC DP I/O D 47 48 DN NC I/O - D - EEPROM Enable Pin "H" : Read Device Descriptor, String Descriptor from EEPROM “L” : Read Device/String Descriptor from internal ROM. Note that CS,SK,EPDI,EPAO is Hi-Z when EPEN is “L” EEPROM Select Pin “L” : 1Kbit Type EEPROM is connected. “H” : 2Kbit/4Kbit EEPROM is connected If EEPROM is not used, EPSEL should be tied to DGND. No Connection Suspend Status Pin "L" : Suspend State "H" : Normal Operation Reset Pin, Low input makes the chip reset sate. Schmitt Trigger input. No Connection No Connection USB bus Non-Inverting pin. Because AK5371 is full speed mode device, 1.5kΩ resistor will be connected between D+ node to VD. USB bus Inverting Pin. No Connection MS0103-E-00 MS0103-E-00 I/O P P O I I/O Ana / Dig A A A A D Description No Connection Analog Power Supply, 3.3V Analog Ground,0V ADC Common Voltage Reference Pin. No Connection Please tie down to AGND for normal operation. No Connection Please tie down to AGND for normal operation. O D EEPROM I/F Chip Select Pin O D Serial Clock Pin 2001/06 4 ASAHI KASEI [AK5371] Absolute Maximum Rating AGND, DGND=0V Parameter Power Supplies Analog Digital |DGND-AGND| Input Current (any pins except for supplies) Analog Input Voltage Digital Input Voltage Ambient Temperature Storage Temperature Note 1. All voltages with respect to ground Symbol Min Max Units VA VD ∆GND IIN VINA VIND Ta Tstg -0.3 -0.3 4.5 4.5 0.3 ±10 VA+0.3 VD+0.3 70 125 V V V mA V V °C °C -0.3 -0.3 0 -40 Warning: Operation at or beyond these limits may results in permanent damage to the device. Normal operation is not guaranteed at these extremes. Recommended Operating Condition AGND, DGND=0V Parameter Power Supplies Analog Digital Symbol Min typ Max Units VA VD 3.0 3.0 3.3 3.3 3.6 3.6 V V All voltages with respect to ground. * AKM assumes no responsibility for the usage beyond the condition in this datasheet. MS0103-E-00 MS0103-E-00 2001/06 5 ASAHI KASEI [AK5371] Analog Characteristics Ta=25°C,VA=VD=3.3V, Signal Frequency=1kHz, Sampling Frequency Fs=44.1kHz BW=20Hz – 20kHz, Test Mode; unless otherwise specified Parameter Min typ Max Units Stereo ADC (2 channel) Resolution 16 bits S/N (A weight) (AMPR2I/AMPL2I input) 84 dBA (IPGA are set to 0dB) USB Normal Mode S/(N+D) (-1dB analog input) 70 dB (IPGA are set to 0dB) USB Normal Mode nd MIC Amplifier (2 Stage) <IPGA>Characteristics Full Scale Input Voltage 1.5 1.7 1.9 Vp-p Gain Control Range -31 +24 dB Step Size 0 1.0 2.0 dB Input Impedance @AMPR2I/AMPL2I pin 40 KΩ st MIC Amplifier (1 Stage) Gain range +20 dB Input Impedance @MICR/MICL 10 20 KΩ S/N (A weight) @MICR/MICL to AMPR1O/AMPL1O 77 dBA MIC Bias (VA) Output Voltage when 4.7KΩ resistor connected 2.0 Vdc Output Impedance 200 500 Ω Output Current 2 mA MIC Bias (Buffer Amp) Output Voltage when 300Ω resistor connected 1.9 2.2 2.5 Vdc Output Current 2 mA Power Supplies Analog 17 25 mA Digital 9 15 mA 26 40 mA Total Power Down (Suspend Mode) 0 160 uA FILTER CHARACTERISTICS (Ta=25°C VA, VD =3.0 - 3.6 V ; fs = 44.1 kHz) Parameter Symbol A/D Digital Filter (Decimation LPF) Passband +/- 0.2 dB PB Stopband SB Passband Ripple PR Stopband Attenuation SA Group Delay GD A/Ddigital Filter (HPF) Frequency Response -3 dB FR -0.5 dB -0.1 dB MS0103-E-00 MS0103-E-00 Min typ 0 26.5 Max Units 17.64 KHz KHz dB dB ms +/- 0.2 68 0.5 6.85 19.2 44.9 Hz Hz Hz 2001/06 6 ASAHI KASEI [AK5371] Digital DC Characteristics Ta=0 - 70°C; VD=3.0 - 3.6V; DGND=0V Measurement under static state All digital pins except DP, DN. Schmitt hysteresis level of RST pin and levels of all test pins will not be tested. Parameter EPDI, EPEN, EPSEL, pin “H” level input voltage EPDI, EPEN, EPSEL pin “L” level input voltage RSTN pin “H” level voltage RSTN pin “L” level voltage CS, SK, EPAO, SUSN pin “H” level output voltage IOH = 2mA CS, SK, EPAO, SUSN pin “L” level output voltage IOL = -2mA Input Leakage Current Symbol VIH VIL VIHR VILR VOH Min 70%VD Typ Max Units V V V V V 30%VD 2.0 0.8 2.4 VOL 0.6 V Iin ±10 µA Switching Characteristics Ta=25°C, VA=VD=3.3V Parameter Symbol Min Typ Max Master Clock Frequency MCLK 11.2896 Reset input width @RSTN pin(low active) Wrst 1.0 DP,DN Single Ended Receiver Threshold for H level VseH 2.0 for L level VseL 0.8 Time Width for USB Reset Signal Recognition*1 Trst_rec 2.7 DP<VseL & DN< VseL to USB Reset mode Device Ready Time from USB Reset Tdrr 10 Ready for transaction after reset Time Width for Suspend Recognition Tsus_rec 3.0 Idle state ( DP > VseL & DN < VseL ) to Suspend mode Resume Time from Suspend First flip of DP/DN from Idle sate Tresm 30 To Device Ready*) Device Ready: VREF, X’tal oscillator, and PLL get stable and bus transaction with normal rate is ready. min 20ms resume time VD Units MHz us V µs ms ms ms min 10ms resume recovery time Resume DP DN RSTN PLL Clock Tdrr Trst_rec Reset Mode Device Connected Figure 1. Mode change with respect to BUS States 1 (Power on and device connected) MS0103-E-00 MS0103-E-00 2001/06 7 ASAHI KASEI [AK5371] Tsus_rec VD”H” D+ DRST”H” PLL Clock Tresm Figure 2. Mode Change with respect to Bus States 2 (Bus transactions) Transmitter Characteristics Ta=25°C; VD=3.3V; DGND=0V; CL=50pF Parameter Symbol Data Rate DR Output Impedance (Hi) Roh DP, DN Rol DP, DP Vohd Vold Iolk Trf/Tff Trfm Vcrs DP, DN DP, DN DP, DN DP, DN DP, DN DP, DN Output Impedance (Lo) “H” level Output Voltage “L” level Output Voltage Tri-state Leakage Current Rise/Fall Time Rise/Fall Time Matching Crossover Point Pins DP,DN Trf Trs Conditions Min 11.97 DP, DN=”H” at Iout = -10mA DP, DN=”L” at Iout = 10mA at Iout =-200uA at Iout =2.2mA 0 < DP, DN< 3.3V Tff Typ 12 Max 12.03 36 Ω 36 Ω 2.8 -10 4 Units MHz 10 100 1.65 0.3 10 20 V V µA ns % V Tfs 90%VDD DP, DN 10%VDD Figure 3. Rise/Fall Time Vcrs DP, DN Figure 4. Crossover Point MS0103-E-00 MS0103-E-00 2001/06 8 ASAHI KASEI [AK5371] Receiver Characteristics Ta=25°C; VD=3.3V; DGND=0V Parameter Symbol Common Mode Range CMR Differential Input Sensitivity DIS Schmitt High Level Voltage Vihs Schmitt Low Level Voltage Vils Pins DP, DN DP, DN DP, DN DP, DN Conditions Min 0.8 200 2.0 Typ Max 0.8 Units V mV V V Vihs DP, DN Vils Figure 5. Schmitt Level Voltage MS0103-E-00 MS0103-E-00 2001/06 9 ASAHI KASEI [AK5371] Overview of AK5371 The AK5371 is the advanced stereo A/D converter, which converts analog signal into USB audio class formats. As the AK5371 incorporates all functions to build USB Audio Input Device, the AK5371 doesn’t require additional micro-controller, memory, and a transceiver. Moreover, as the AK5371 also has 20dB fixed gain pre-amplifier in addition to programmable gain amplifier (IPGA) whose range is from +24dB to –31dB, this device is suitable for USB microphone, especially microphone array. USB microphone can be manufactured easily by only four main components; the AK5371, one crystal, one regulator, and microphone unit(s). As the AK5371 also has EEPROM interface, descriptors can be customized easily. The AK5371 includes the following blocks: 1. 2 channel 16bit A/D converter a) 84dBA@fs=44.1kHz 2. Programmable Gain Amplifier (IPGA) a) Gain Range: from +24dB to -31dB, b) Gain Step: 1dB/step 3. Fixed Gain Preamplifier a) 20dB 4. FIFO Synchronization between A/D converter and USB bus a) Memory Size 400 bytes (16bit wide x 100 depth x 2 channel) 5. PLL a) b) 11.2896MHz crystal Two PLLs - A/D_PLL: generate clock for fs=8kHz, 48kHz - System_PLL : generate USB system clock 6. Audio Format a) supports 5 frequencies : 8kHz, 11.025kHz, 22.05kHz, 44.1kHz, 48kHz b) 2 audio formats - mono 16bit LSB first - stereo 16bit LSB first 7. USB Serial Interface Engine a) Process USB Standard Requests 8. Control block of Audio Device Class a) Translate internal A/D format to USB audio class format b) Process USB Audio Class Request - Mute - Gain/Attenuation - Sampling Frequency Control 9. USB transceiver 10. EEPROM I/F Microwire (4-wire) type EEPROM can be used to customize Device/String Descriptor. - 1K bit (AK93C45A) - 2K bit (AK93C55A) - 4Kbit (AK93C65A) 11. USB Suspend/Resume Support The AK5371 supports 5 sampling frequencies (8kHz, 11.025kHz, 22.05kHz, 44.1kHz, 48kHz). In order to support these frequencies, the AK5371 incorporates PLL, which generates system clock and master clock for fs=8kHz, and 48kHz Mute, volume and audio format including sampling frequency are controlled by USB audio class request. The AK5371 goes to suspend mode when the device doesn’t receive SOF for the period more than 3ms. All blocks including master clock stop the function to observe USB specification, 500µA , until receiving the resume signal. The AK5371 notifies the current state (normal state or suspend state) by SUS_N pin. As the AK5371 has Microwire EEPROM I/F, the vendors can customize iManifacterer, iProduct, and the related strings to their own ID, and string. MS0103-E-00 MS0103-E-00 2001/06 10 ASAHI KASEI [AK5371] Descriptor Overview When the device is connected to USB bus, the host assigns specific address to the device. Then the host reads the device information, which is called as descriptor, through default pipe (Endpoint 0). The AK5371 consists of one Device Descriptor, one Configuration Descriptor, two Interface Descriptors, and two Endpoint Descriptors. Figure 6 shows Descriptor’s hierarchy. Device Device Descriptor Configuration Configuration Descriptor Standard Audio Control Interface Descriptor Standard AS Interface Descriptor Alt. Setting 0 Class-Specific Audio Control Interface Descriptor Interface 0 Interface 1 Standard AS Interface Descriptor Alt. Setting 1 Standard AS Interface Descriptor Alt. Setting 2 Class-Specific Audio Streaming Interface Descriptor Class-Specific Audio Streaming Interface Descriptor Class-Specific AS Format Type Descriptor Class-Specific AS Format Type Descriptor Standard AS Isochronous Endpoint Descriptor Standard AS Isochronous Endpoint Descriptor Class-Specific AS Isochronous Endpoint Descriptor Class-Specific AS Isochronous Endpoint Descriptor Class-Specific Descriptor StandardInterface Descriptor Endpoint (IN) Figure 6. Descriptor Hierarchy MS0103-E-00 MS0103-E-00 2001/06 11 ASAHI KASEI [AK5371] Audio Format of the AK5371 The AK5371 supports two audio formats: 16bit/mono and 16bit/stereo. This feature can avoid the unnecessary occupation of USB bandwidth. 16bit/mono is assigned to <Interlace 1, Alt1>, 16bit/stereo is assigned to <Interface 1, Alt2>. The A/D data on USB bus is LSB first, Left channel first. When 16bit/mono audio format is selected, the AK5371 outputs left channel data on the USB bus. Audio format is changed by “Set Interface” Request. Synchronization The AK5371 operates as Asynchronous Device. A/D converter in the AK5371 operates asynchronously with USB SOF timing. The data from A/D converter are sent continuously to a buffer memory while the data are burstly transferred at the interval of SOF on the USB. In order to arbitrate the difference of timing, AK5371 has a FIFO memory with a capacity of 2-frame depth .The average sampling rate calculating from USB frame should be in accordance with A/D sampling rate (fs). The AK5371 sends all A/D samples that were stored in the last frame to avoid overflow or underflow of FIFO. The following figure shows an example. When sampling frequency is set to 44.1kHz, the AK5371 sends 45 samples once per ten times, and sends 44 samples in other frames. Average frequency is 44.1kHz. See Figure 7. N Frame (N+1) Frame 44 samples 44 samples (N+9) Frame 45 samples (N+10) Frame 44 samples Figure 7. Synchronization Power Management Control When idle state continues for 3ms, the AK5371 goes to suspend state and forces almost all blocks including PLL, ADC block and mic bias into stopping in order to observe 500µA, which is USB suspend current requirement. The device resumes the normal operation within 30ms after the device receives resume signal. In the normal operation, MICBIAS outputs the voltage to supply the microphone’s bias voltage. SUSN pin shows USB bus status; suspend mode (“L") or normal operation (“H"). SUSN pin can be used for external power control. The AK5371 is very low power device at both normal state and suspend state. However, note that USB suspend current requirement, 500µA, specifies the current which is totally consumed by not only the AK5371, by also regulator(s), and resistors. Therefore, low power regulator should be selected to design USB microphone. Feature Unit Control & Frequency Control When the AK5371 receives “SET_FEATURE_UNIT_CONTROL” request, the device decodes the request and sets the value. Note that only CUR value is valid for “SET_FEATURE_UNIT_CONTROL” request, and that MIN/MAX/RES value is invalid. When the AK5371 receives “GET_FEATURE_UNIT_CONTROL” request, the device decodes the request and returns the value to the host. CUR/MAX/MIN/RES value is valid for "Get Volume Request", but only CUR value is meaningful for "Get Mute Request". When the AK5371 receives “SET_ENDPOINT_CONTROL” request, it changes sampling frequency(fs). If fs is not supported, the device forces to set the appropriate fs which it supports. When the AK5371 receives “GET_ENDPOINT_CONTROL” request, it sends back the current value to the host. MS0103-E-00 MS0103-E-00 2001/06 12 ASAHI KASEI [AK5371] EEPROM I/F The AK5371 has EEPROM I/F for customizing Device Descriptor, and String Descriptor. idVendor(2byte), idProduct(2byte), bcdDevice(2byte), iManufacturer(1byte), iProduct(1byte) in Device Descriptor and related String Descriptor can be customized. MicrowireTM type, 1K bit, 2K bit, or 4K bit EEPROM can be used. Note that word length of iManufacterer and iProduct is fixed to 52 bytes each for 1K bit EEPROM, 102 bytes for 2K/4K bit EEPROM. The AK5371 automatically reads Device Descriptor from the EEPROM and stores internal memory after USB reset. When the AK5371 receives “GET String Descriptor" request, the AK5371 starts reading from EEPROM. The AK5371 continues to send NAK packet while it is reading String from EEPROM. Memory mapping of EEPROM is the following. Device Descriptor (18 bytes) String Descriptor Lang ID (4 bytes index = 0) String Descriptor iManufacturer (52 or 102bytes index =1) String Descriptor iProduct (52 or 102 bytes index = 2) Note that EEPROM address is 16bit boundary. 1K bit (AK93C45A) 00h - 08h 09h - 0Ah 0Bh - 24h 25h - 3Eh 2K/4K bit (AK93C55A / 65A) 00h - 08h 09h - 0Ah 0Bh - 3Dh 3Eh - 71h If 2K/4K bit EEPROM is used, EPSEL pin should be tied to VD. if 1K bit EEPROM is connected to the device, EPSEL should be tied to digital ground. Device Descriptor and String Descriptor should be stored in EEPROM before the AK5371 is powered up. EPEN pin should be tied to "H" to activate if Descriptors are read from external EEPROM. If internal ROM is used, not only EPEN pin but also EPSEL pin should be tied to DGND. Note that CS pin, SK pin, and EPAO pin are Hi-Z state when EPEN is “L”. EPDI pin is internally pulled down. MS0103-E-00 MS0103-E-00 2001/06 13 ASAHI KASEI [AK5371] System Block Diagram The following figure shows the system connection diagram. This is an example which uses external 1K bit EEPROM (AK93C45A) as Device and String Descriptor. If EEPROM is not used, EPEN pin should be tied to DGND. Ceramic capacitors (0.1uF) for VA pin, VD pin, VREF pin and VCOM pin should be located as near as possible. <REMARK> This drawing does NOT mean physical pin locations/ordering 10uH 10Ω Regulator 0.1u 10u R1:4.7k 0.1u 4.7u 0.1u 4.7u 0.1u 100u 0.1u 0.1u 4.7u 4.7u 0.1u 56k R1:4.7k R0 VA AGND BGND VD DGND VREF VCOM MICBIAS 10u RSTN 3300p CS SK EPAO EPDI 100u 0.1u C1:1.0u< C2:0.33u Phone Jack C1:1.0u< STEREO SW C2:0.33u MICR AMPR1O Testmode 1 Testmode 2 Testmode 3 Test AMPR2I MICL AMPL1O 1.5k D+ DP AMPL2I AMP2RO EEPROM AMP2O DN LFLT1,2 XTALIN XTALOUT 51k C3:1000p C3:1000p 8200p 18k 6800p 15p D- GND 11.2896M 15p To Host/Hub 5V GND analog GND digital GND C1 is specified for lower end cut-off frequency C3 forms Anti-aliasing filter in conjuction with the internal resistor at AMPR2O/AMPL2O R0: 0Ω resister when BIASSEL is Low 300Ω (TBD) resister when BIASSEL is High MS0103-E-00 MS0103-E-00 2001/06 14 ASAHI KASEI [AK5371] AK5371 Descriptors Specification 1 Device descriptor Offset 0 1 2 4 5 6 7 8 10 12 14 15 16 17 Field bLength bDescriptorType bcdUSB bDeviceClass bDeviceSubClass bDeviceProtocol bMaxPacketSize0 idVendor idProduct bcdDevice iManufacturer iProduct iSerialNumber bNumConfigurations Size 1 1 2 1 1 1 1 2 2 2 1 1 1 1 Value 0x12 0x01 0x0110 0x00 0x00 0x00 0x08 0x0556 0x0002 0x0001 0x01 0x02 0x00 0x01 Description Size of this descriptor in bytes DEVICE descriptor 1.10 – current revision of USB spec. Device defined at Interface level Unused Unused 8 bytes AKM’s Vendor ID 00 means Audio Product, 02 is AKMproduct ID , Device release code “AKM” “AK5371” Unused One configuration 2 Configuration Descriptor The configuration block consists of a configuration descriptor followed by interface, endpoint, and class-specific descriptors. Offset Field Size Value Description 0 bLength 1 0x09 Size of this descriptor 1 bDescriptorType 1 0x02 CONFIGURATION descriptor 2 wTotalLength 2 0x00B1 Length of entire configuration block Total 177 bytes including this interface descriptor. Two interfaces 4 bNumInterfaces 1 0x02 5 bConfigurationValue 1 0x01 Index of this configuration 6 iConfiguration 1 0x00 Null string 7 bmAttributes 1 0x80 Bus Powered Device 8 MaxPower 1 0x2D Power consumption: 90mA 3 Interface Descriptor 3.1 Standard Audio Control Interface descriptor 3.1.1 This descriptor describes a standard interface which includes USB class code and the index to class-specific information. Offset Field Size Value Description 0 bLength 1 0x09 Size of this descriptor 1 bDescriptorType 1 0x04 INTERFACE descriptor 2 bInterfaceNumber 1 0x00 Index of this interface 3 bAlternateSetting 1 0x00 Index of this setting 4 bNumEndpoints 1 0x00 Endpoint 0 5 bInterfaceClass 1 0x01 AUDIO 6 bInterfaceSubclass 1 0x01 AUDIO_CONTROL 7 bInterfaceProtocol 1 0x00 Unused 8 iInterface 1 0x00 null string MS0103-E-00 MS0103-E-00 2001/06 15 ASAHI KASEI [AK5371] 3.2 Class-specific Audio Control Interface 3.3 Class-specific Audio Control Interface Header Descriptor 3.3.1 Offset 0 1 2 3 5 7 8 Contains general information about the audio device. Field Size Value Description bLength 1 0x09 Size of this descriptor bDescriptorType 1 0x24 CS_INTERFACE bDescriptorSubtype 1 0x01 HEADER subtype bcdADC 2 0x0100 Revision of class specification – 1.0 wTotalLength 2 0x0028 Total size of class-specific Audio Control Interface descriptors (includes this descriptor) bInCollection 1 0x01 Number of streaming interfaces baInterfaceNr(1) 1 0x01 Streaming interface number 1 belongs to this audio control interface. 3.3.2 Input terminal descriptor This descriptor describes the signal coming through the input port NumChannels is 1(monaural) and ChannelConfig is set no position. Terminal type is Microphone. Offset Field Size Value Description 0 bLength 1 0x0C Size of this descriptor 1 bDescriptorType 1 0x24 CS_INTERFACE 2 bDescriptorSubtype 1 0x02 INPUT_TERMINAL subtype 3 bTerminalID 1 0x01 ID of this terminal 4 wTerminalType 2 0x0201 Terminal is Microphone 6 bAssocTerminal 1 0x02 ID of associated Output Terminal is 0x02 7 bNrChannels 1 0x02 Two channels (Stereo) 8 wChannelConfig 2 0x0003 Left/Right Front 10 iChannelNames 1 0x00 Unused 11 iTerminal 1 0x00 Unused 3.3.3 Output terminal descriptor This descriptor describes the USB stream to host. Offset Field Size Value 0 bLength 1 0x09 1 bDescriptorType 1 0x24 2 bDescriptorSubtype 1 0x03 3 bTerminalID 1 0x02 4 wTerminalType 2 0x0101 6 bAssocTerminal 1 0x01 7 bSourceID 1 0x03 8 iTerminal 1 0x00 3.3.4 Offset 0 1 2 3 4 5 6 7 8 9 Description Size of this descriptor CS_INTERFACE OUTPUT_TERMINAL subtype ID of this terminal USB Streamer ID of associate Input Terminal is 0x01 From Feature Unit Unused Feature Unit descriptor Field bLength bDescriptorType bDescriptorSubtype bUnitID bSourceID bControlSize Size 1 1 1 1 1 1 Value 0x0A 0x24 0x06 0x03 0x01 0x01 bmaControls(0) 1 0x01 bmaControls(1) 1 0x02 bmaControls(2) 1 0x02 iFeature 1 0x00 Note that there is never endpoint descriptor for endpoint 0. MS0103-E-00 MS0103-E-00 Description Size of this descriptor CS_INTERFACE FEATURE_UNIT descriptor subtype ID of this feature Unit ID to Terminal to which this is connected. Size in bytes of an element of the bmaControl() D0(Mute) is enable for Channel 0 D1(Volume) is enable for ch 1(Left) D1(Volume) is enable for ch 2 (Right) Unused 2001/06 16 ASAHI KASEI [AK5371] 3.4 Audio streaming interface 3.4.1 Offset 0 1 2 3 4 5 6 7 8 Zero bandwidth interface descriptor Field Size Value bLength 1 0x09 bDescriptorType 1 0x04 bInterfaceNumber 1 0x01 bAlternateSetting 1 0x00 bNumEndpoints 1 0x00 bInterfaceClass 1 0x01 bInterfaceSubclass 1 0x02 bInterfaceProtocol 1 0x00 iInterface 1 0x00 Description Length of this descriptor INTERFACE descriptor Index of this interface Index of this setting Endpoints 0 AUDIO AUDIO_STREAMING Unused null string 3.4.2 Offset 0 1 2 3 4 5 6 7 8 Interfacedescriptor( Alt = 1, 16bit Mono) Field Size Value bLength 1 0x09 bDescriptorType 1 0x04 bInterfaceNumber 1 0x01 bAlternateSetting 1 0x01 bNumEndpoints 1 0x01 bInterfaceClass 1 0x01 bInterfaceSubclass 1 0x02 bInterfaceProtocol 1 0x00 iInterface 1 0x00 Description Length of this descriptor INTERFACE descriptor Index of this interface Index of this setting Endpoint 1 AUDIO AUDIO_STREAMING Unused null string 3.4.3 Offset 0 1 2 3 4 5 Class-specific audio streaming interface descriptor Field Size Value Description bLength 1 0x07 Length of this descriptor bDescriptorType 1 0x24 CS_INTERFACE descriptor bDescriptorSubtype 1 0x01 AS_GENERAL bTerminalLink 1 0x02 Unit ID of terminal(Output Terminal ID) bDelay 1 0x01 Interface delay wFormatTag 2 0x0001 PCM 3.4.4 Offset 0 Type I format type descriptor Field Size Value blength 1 0x17 1 2 3 4 5 6 7 8 11 14 17 20 bDescriptorType bdescriptorSubtype bformatType bNrChannels bSubFrameSize bBitResolution bSamFreqType tSamFreq[0] tSamFreq[1] tSamFreq[2] tSamFreq[3] tSamFreq[4] MS0103-E-00 MS0103-E-00 1 1 1 1 1 1 1 3 3 3 3 3 Description Size of this descriptor 0x24 0x02 0x01 0x01 0x02 0x10 0x05 0x001F40 0x002B11 0x005622 0x00AC44 0x00BB80 CS_INTERFACE FORMAT_TYPE FORMAT_TYPE_I One channel Two bytes per slot 16 bits Five frequencies 8000Hz 11025Hz 22050Hz 44100Hz 48000Hz 2001/06 17 ASAHI KASEI [AK5371] 3.5 Endpoint descriptor 3.5.1 Offset 0 1 2 3 4 6 7 8 Standard Endpoint Descriptor Field Size Value bLength 1 0x09 bDescriptorType 1 0x05 bendpointAddress 1 0x81 bmAttributes 1 0x05 wMaxPacketSize 2 0x0064 wInterval 1 0x01 bRefresh 1 0x00 bSynchAddress 1 0x00 3.5.2 Offset 0 1 2 3 4 5 Class-specificisochronous audio data endpoint descriptor Field Size Value Description bLength 1 0x07 Size of this descriptor bDescriptorType 1 0x25 CS_ENDPOINT bDescriptorSubtype 1 0x01 GENERAL bmAttributes 1 0x01 Sample rate control bLockDelayUnits 1 0x00 Unused wLockDelay 2 0x0000 MS0103-E-00 MS0103-E-00 Description Length of this descriptor ENDPOINT descriptor Endpoint 1, IN direction Isochronous, asynchronous, not shared 2byte*50sample*1ch=100 byte/frame One packet every frame (Must be set to 1) 2001/06 18 ASAHI KASEI [AK5371] 3.5.3 Offset 0 1 2 3 4 5 6 7 8 Interface descriptor(Alt = 2, 16bit Stereo) Field Size Value bLength 1 0x09 bDescriptorType 1 0x04 bInterfaceNumber 1 0x01 bAlternateSetting 1 0x02 bNumEndpoints 1 0x01 bInterfaceClass 1 0x01 bInterfaceSubclass 1 0x02 bInterfaceProtocol 1 0x00 iInterface 1 0x00 3.5.4 Offset 0 1 2 3 4 5 Class-specific audio streaming interface descriptor Field Size Value Description bLength 1 0x07 Length of this descriptor bDescriptorType 1 0x24 CS_INTERFACE descriptor bDescriptorSubtype 1 0x01 AS_GENERAL bTerminalLink 1 0x02 Unit ID of terminal(Output Terminal ID) bDelay 1 0x01 Interface delay wFormatTag 2 0x0001 PCM 3.5.5 Offset 0 Type I format type descriptor Field Size Value blength 1 0x17 1 2 3 4 5 6 7 8 11 14 17 20 bDescriptorType bdescriptorSubtype bformatType bNrChannels bSubFrameSize bBitResolution bSamFreqType tSamFreq[0] tSamFreq[1] tSamFreq[2] tSamFreq[3] tSamFreq[4] MS0103-E-00 MS0103-E-00 1 1 1 1 1 1 1 3 3 3 3 3 Description Length of this descriptor INTERFACE descriptor Index of this interface Index of this setting Endpoint 1 AUDIO AUDIO_STREAMING Unused null string Description Size of this descriptor 0x24 0x02 0x01 0x02 0x02 0x10 0x05 0x001F40 0x002B11 0x005622 0x00AC44 0x00BB80 CS_INTERFACE FORMAT_TYPE FORMAT_TYPE_I Two channel Two bytes per slot 16 bits Five frequencies 8000Hz 11025Hz 22050Hz 44100Hz 48000Hz 2001/06 19 ASAHI KASEI [AK5371] 3.6 Endpoint descriptor 3.6.1 Offset 0 1 2 3 4 6 7 8 Standard Endpoint Descriptor Field Size Value bLength 1 0x09 bDescriptorType 1 0x05 bendpointAddress 1 0x81 bmAttributes 1 0x05 wMaxPacketSize 2 0x00C8 wInterval 1 0x01 bRefresh 1 0x00 bSynchAddress 1 0x00 3.6.2 Offset 0 1 2 3 4 5 Class-specificisochronous audio data endpoint descriptor Field Size Value Description bLength 1 0x07 Size of this descriptor bDescriptorType 1 0x25 CS_ENDPOINT bDescriptorSubtype 1 0x01 GENERAL bmAttributes 1 0x01 Sample rate control bLockDelayUnits 1 0x00 Unused wLockDelay 2 0x0000 MS0103-E-00 MS0103-E-00 Description Length of this descriptor ENDPOINT descriptor Endpoint 1, IN direction Isochronous, asynchronous, not shared 2byte*50sample*2ch=200 byte/frame One packet every frame (Must be set to 1) 2001/06 20 ASAHI KASEI [AK5371] 3.7 String descriptor 1 String descriptors use UNICODE. except for LANGID. 3.7.1 Offset 0 1 2 LANGID (0 x00) Field Field bLength bDescriptorType bString 3.7.2 Offset 0 1 2 iManufacterer 0x01) ( Field in Device Descriptor Field Size Value Description bLength 1 0x34 Length of this descriptor bdescriptorType 1 0x03 STRING descriptor “AKM ” bString 50 0x0041 0x004B 0x004D 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 MS0103-E-00 MS0103-E-00 Size 1 1 2 Value 0x04 0x03 0x0409 Description Length of this descriptor STRING descriptor “English(US)” 2001/06 21 ASAHI KASEI 3.7.3 Offset 0 1 2 iProduct (0x02) Field in Device Descriptor Field Size Value bLength 1 0x34 bDescriptorType 1 0x03 bString 50 0x0041 0x004B 0x0035 0x0033 0x0037 0x0031 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 0x0020 MS0103-E-00 MS0103-E-00 [AK5371] Description Length of this descriptor STRING descriptor “AK5371 ” 2001/06 22 ASAHI KASEI [AK5371] 4 Standard requests 4.1 Clear Feature The AK5371 accepts “Clear Feature” request without stall. Though this request does not influence to the operation of the device, the AK5371 does not support this request. 4.2 Get Configuration The AK5371 returns Configuration value. Field Size Value Offset 0 bmRequestType 1 0x80 1 bRequest 1 0x08 2 wValue 2 0x0000 4 wIndex 2 0x0000 6 wLength 2 0x0001 Description GET_CONFIGURATION AKM USB Mic. has one configuration. 4.3 Get Descriptor Offset 0 1 2 Field bmRequestType bRequest wValue Size 1 1 2 Value 0x80 0x06 0xZZZZ 4 wIndex 2 0x0000 6 wLength 2 0xZZZZ Description GET_DESCRIPTOR ZZZZ is assigned by host: High Byte is Descriptor Type, Low Byte is Index. DEVICE : 0x0100 : (Index is 0 only) CONFIGURATION : 0x0200 STRING: 0x03??(?? is 00, 01, 02) if wValue is DEVICE or CONFIGURATION, wIndex is zero. If wValue is 0x0300(LANGID), wIndex is zero. If wValue is 0x0301 or 0x0302, wIndex is 0x0409“English(US)”. Descriptor Length (ZZZZ is assigned by host) 4.4 Get Interface The AK5371 returns the current bAlternateSetting value. Offset Field Size Value Description 0 bmRequestType 1 0x81 1 bRequest 1 0x0A GET_INTERFACE 2 wValue 2 0x0000 ZERO 4 wIndex 2 0x0000 Audio Control Interface 0x0001 Audio Streaming Interface 6 wLength 2 0x0001 AKM USB Mic. Has zero bandwidth Audio Streaming Interface and normal Audio Streaming Interface. MS0103-E-00 MS0103-E-00 2001/06 23 ASAHI KASEI [AK5371] 4.5 Get Status Offset 0 Field bmRequestType 1 2 4 6 bRequest wValue wIndex wLength Size 1 1 2 2 2 Value 0x80 0x81 0x82 0x00 0x0000 Description DEVICE INTERFACE ENDPOINT GET_STATUS ZERO 0x0002 The AKM USB MIC returns the following status. a)Device : 0x00 ( AKM USB MIC is bus-powered device) b)Interface: 0x00 (All Zero) c)Endpoint : 0x00 4.6 Set Address AKM USB MIC stores the wValue in the internal memory as Device Address. In addition to this, the device returns ACK. Offset Field Size Value Description 0 bmRequestType 1 0x00 Zero 1 bRequest 1 0x05 SET_ADDRESS 2 wValue 2 0xZZZZ Device Address : ZZZZ is assigned by host 4 wIndex 2 0x0000 Zero 6 wLength 2 0x0000 Zero 4.7 Set Configuration AKM USB MIC is placed to configured state only wValue of this request is 0x0001. In addition to this, the device returns ACK. Offset Field Size Value Description 0 bmRequestType 1 0x00 Zero 1 bRequest 1 0x09 SET_CONFIGURATION 2 wValue 2 0x0000 Unconfigured State 0x0001 AKM USB MIC is set to configured state others Invalid 4 wIndex 2 0x0000 Zero 6 wLength 2 0x0000 Zero MS0103-E-00 MS0103-E-00 2001/06 24 ASAHI KASEI [AK5371] 4.8 Set Feature The AK5371 accepts “Set Feature” request without stall. However note that the AK5371 does not support this request. 4.9 Set Interface Audio format can be changed by the combination of Interface Number and Alternate Setting. Only 0x0000 is valid if wIndex is 0x0000 Offset Field Size Value Description 0 bmRequestType 1 0x01 ONE D7 0 = Host to device D6..5 0 = Standard request D4..0 1 = Recipient is interface 1 bRequest 1 0x0B SET_INTERFACE 2 wValue 2 Alternate Setting 0x0000 Control Interface or Zero Bandwidth 0x0001 16bit Mono 0x0002 16bit Stereo 4 wIndex 2 0x0000 Audio Control Interface 0x0001 Audio Streaming Interface 6 wLength 2 0x0000 Zero MS0103-E-00 MS0103-E-00 2001/06 25 ASAHI KASEI [AK5371] 5 Device specificRequests AKM USB Microphone supports ONLY SET_CUR as bRequest field in Set Request Values. 5.1 Audio Control Request AKM USB microphone support ONLY Feature Unit Control Request, not support other requests. Addition to this, it only supports SET_CUR value as bRequest field in Set Feature Unit Control Request Values. All Audio Control Requests are applied to channel 0,1,2, which means master , left and right channel. 5.1.1 Set Feature Unit Control Request AKM USB Microphone supports only one form of parameter block. Mute control is applied to master channel (channel 0) a) Mute Control Offset Field Size Value Description 0 bmRequestType 1 0x21 1 bRequest 1 0x01 SET_CUR 2 wValue 2 0x0100 MUTE_CONTROL | CHANNEL_0 4 wIndex 2 0x0300 Upper Byte : bUnit ID field in Feature Unit Descriptor.(0x03) Lower Byte : Audio Control Interface(0x00) 6 wLength 2 0x0001 The Length of Mute Control Parameter Block The parameter block of mute control is the following. Offset Field Size Value Description 0 bMute 1 0x01 TRUE 0x00 FALSE a) Volume Control Left (channel 1) volume and right (channel 2) volume are controlled independently. Offset Field Size Value Description 0 bmRequestType 1 0x21 1 bRequest 1 0x01 SET_CUR 2 wValue 2 0x0201 VOLUME_CONTROL | CHANNEL_1 0x0202 VOLUME_CONTROL | CHANNEL_2 4 wIndex 2 0x0300 Upper Byte : bUnit ID field in Feature Unit Descriptor.(0x03) Lower Byte : Audio Control Interface(0x00) 6 wLength 2 0x0002 Volume Control The parameter block of mute control is the following. Offset Field Size Value Description 0 wVolume 2 0xZZZZ The value is mapped to the volume register value. (refer to Table 1 conversion table ) ZZZZ is assigned by the host If the wVolume exceeds the range, the AK5371 forces the value into the range. Please see the conversion table in the Get Feature Unit Control Request. MS0103-E-00 MS0103-E-00 2001/06 26 ASAHI KASEI [AK5371] 5.1.2 Get Feature Unit Control Request AKM USB Microphone supports only one form of parameter block. a) Mute Control Offset Field Size Value Description 0 bmRequestType 1 0xA1 1 bRequest 1 0x81 GET_CUR 2 wValue 2 0x0100 MUTE_CONTROL | CHANNEL_0 4 wIndex 2 0x0300 Upper Byte : bUnit ID field in Feature Unit Descriptor.(0x03) Lower Byte : Audio Control Interface(0x00) 6 wLength 2 0x0001 The Length of Mute Control Parameter Block The device outputs the current setting of mute status. Offset Field Size Value Description 0 bMute 1 0x01 TRUE 0x00 FALSE b) Volume Control Offset Field 0 bmRequestType 1 bRequest Size 1 1 2 wValue 2 4 wIndex 2 Value 0xA1 0x81 0x82 0x83 0x84 0x0201 0x0202 0x0300 6 wLength 2 0x0002 Description GET_CUR GET_MIN GET_MAX GET_RES VOLUME_CONTROL | CHANNEL_1 VOLUME_CONTROL | CHANNEL_2 Upper Byte : bUnit ID field in Feature Unit Descriptor.(0x03) Lower Byte : Audio Control Interface(0x00) Volume Control The parameter block of Volume Control is the following. Offset Field Size Value Description 0 wVolume 2 0xZZYY bRequest = GET_CUR : returns current volume. YY must be 00h 0xE100 bRequest = GET_MIN : -31dB 0x1800 bRequest = GET_MAX : +24dB 0x0100 bRequest = GET_RES : 1.0dB Table 1 is the conversion map of USB class and internal volume register. When host requests the volume value which is larger than the MAX value in the device, the device is set the MAX value to the volume. When host requests the volume value which is smaller than the MIN value in the device, the device is set the MIN value to the volume. RES value is 1.0dB. MS0103-E-00 MS0103-E-00 2001/06 27 ASAHI KASEI [AK5371] Field wVolume 0x7FFF -------0x1800 0x17FF --------0x1701 0x1700 0x16FF --------0x1201 0x1200 ----------------0x02FF --------0x0201 0x0200 0x01FF --------0x0101 0x0100 0x00FF --------0x0001 0x0000 0xFFFF -------0xFF01 0xFF00 0xFEFF -------0xFE01 0xFE00 ----------------0xE200 0xE1FF --------0xE101 0xE100 0xE1FF --------0x8000 Internal Value 0x1800 -----0x1800 0x1700 -----0x1700 0x1700 0x1600 -----0x1200 0x1200 ----------------0x0200 --------0x0200 0x0200 0x0100 --------0x0100 0x0100 0x0000 --------0x0000 0x0000 0xFF00 -------0xFF00 0xFF00 0xFE00 -------0xFE00 0xFE00 ----------------0xE200 0xE100 --------0xE100 0xE100 0xE100 0xE100 value 24.0000 --------24.0000 23.0000 -------23.0000 23.0000 22.0000 -------18.0000 18.0000 --------------2.0000 -------2.0000 2.0000 1.0000 --------1.0000 1.0000 0.0000 --------0.0000 0.0000 -1.0000 --------1.0000 -1.0000 -2.0000 --------2.0000 -2.0000 -----------------30.0000 -31.0000 ---------31.0000 -31.0000 -31.0000 ---------31.0000 Step 1.0dB Table 1 Conversion Table of Volume Control MS0103-E-00 MS0103-E-00 2001/06 28 ASAHI KASEI [AK5371] 5.2 Endpoint Control Request The AK5371 supports five sampling frequencies. The sampling rate is changed when “Set Endpoint Control Request ” is issued. SET_CUR, GET_CUR of bRequest is only supported. GET_MIN, GET_ MAX, and GET_RES of bRequest are not supported. 5.2.1 Set Endpoint Control Request Offset 0 1 2 Field bmRequestType bRequest wValue Size 1 1 2 Value 0x22 0x01 0x0100 4 wIndex 2 0x0081 6 wLength 2 0x0003 Description SET_CUR Upper byte: SAMPLING_FREQ_CONTROL (0x01) Lower byte : zero Upper Byte : zero Lower Byte : Endpoint Address (0x81) The Length of Sampling Frequency Parameter Block The parameter block of mute control is the following. Offset Field Size Value Description 0 iSampleFreq 3 0xYYYYYY The following five values are valid. Others are invalid. 0x001F40 : 8kHz 0x002B11 : 11.025kHz 0x005622 : 22.05kHz 0x00AC44 : 44.1kHz(default) 0x00BB80 : 48kHz If the iSampleFreq is different from the above values, the AK5371 forces sampling frequency to the appropriate value. 5.2.2 Get Endpoint Control Request Offset 0 1 2 Field bmRequestType bRequest wValue Size 1 1 2 Value 0xA2 0x81 0x0100 4 wIndex 2 0x0081 6 wLength 2 0x0003 Description GET_CUR Upper byte: SAMPLING_FREQ_CONTROL (0x01) Lower byte : zero Upper Byte : zero Lower Byte : Endpoint Address (0x81) The Length of Sampling Frequency Parameter Block The parameter block of mute control is the following. Offset Field Size Value Description 0 iSampleFreq 3 0xYYYYYY The following five values are valid. invalid. 0x001F40 : 8kHz 0x002B11 : 11.025kHz 0x005622 : 22.05kHz 0x00AC44 : 44.1kHz 0x00BB80 : 48kHz MS0103-E-00 MS0103-E-00 Others are 2001/06 29 ASAHI KASEI [AK5371] Package 48pin LQFP(Unit:mm) 1.70Max 9.0 ± 0.2 0.10 ± 0.07 7.0 36 1.4TYP 25 48 9.0 ± 0.2 24 7.0 37 13 1 12 0.17 ± 0.05 0.5 0.19 ± 0.05 0.10 M 0° ∼ 10° 0.10 MS0103-E-00 MS0103-E-00 0.5 ± 0.2 2001/06 30 ASAHI KASEI [AK5371] Marking AK5371VQ XXXXXXX 1 1) Pin #1 indication 2) Date Code: XXXXXXX (7 digits) 3) Marking Code: AK5371VQ 4) Asahi Kasei Logo MS0103-E-00 MS0103-E-00 2001/06 31 ASAHI KASEI [AK5371] IMPORTANT NOTICE • These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. • AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. • Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. • AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b)A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. • It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. MS0103-E-00 MS0103-E-00 2001/06 32