AIMTEC AM1N-2409DH60-N 1 watt dc-dc converter Datasheet

AM1N-N Series
DC-DC CONVERTERS
1 watt dc-dc converters
•
24-PIN DIP PACKAGE
•
LOW PROFILE PLASTIC PACKAGE
•
HIGH EFFICIENCY UP TO 81%
•
UL94-VO PACKAGE
•
INPUT/OUTPUT ISOLATION: 6000VDC
•
OPERATING TEMPERATURE: -40°C ... +85°C
•
PIN-COMPATIBLE WITH MULTIPLE MANUFACTURERS
GENERAL DESCRIPTION
Our AM1N-N series is a family of cost effective 1W
single and dual output DC-DC converters. These
converters combine plastic package in a 24-pin DIP
compatible case with high performance feature such as
6000VDC input/output isolation voltage. Twenty four
models operate from input voltages of 5, 12 & 24VDC
with output voltages of 5, 9, 12, 15, ±5, ±9, ±12, ±15VDC.
Operation is specified over the full operating temperature
range of -40°C to +85°C with no derating required.
Cooling is by free-air convection.
ELECTRICAL SPECIFICATIONS
Specifications typical at +25°C, nominal input voltage, rated output current unless otherwise specified
Input Specifications:
Voltage range
Filter
±10 %
Capacitor
Isolation Specifications:
Rated voltage (60 sec)
Resistance
6000 VDC
> 1000 MOhm
General Specifications:
Efficiency
Switching Frequency
72% to 81%
35 KHz, typ. 100% load
Physical Specifications
Dimensions
Weight
Case material
32.3x14.7x9.4 mm
1.27x0.58x0.37 inches
16 g
Plastic UL94-VO
Output Specifications:
Voltage accuracy
Ripple & noise (at 20MHz BW)
Short circuit protection
Line voltage regulation
Load voltage regulation
Temperature Coefficient
See tolerance
envelope graph
75mVp-p, typ.
1 sec.
±1.2%/1% of Vin max.
10%, max.
±0.03%/°C, max.
Environmental Specifications:
Operating temperature (ambient) -40°C to +85°C
Storage temperature
-55°C to +125°C
Case temperature
+95°C, max.
Derating
None required
Humidity (non-condensing)
Up to 90%
Cooling
Free-air Convection
MTBF: > 1,211,000 hrs (MIL-HDBK-217F, Ground Benign, t=+25°C)
Specifications are subject to change without notification
OUTLINE DIMENSIONS & PIN CONNECTIONS
Single output
24
Dual output
Pin
Function
Pin
Function
1
2
8,17
10,15
12,13
+V Input
-V Input
N.C.
OV
+V Output
1
2
8,17
10,15
12,13
+V Input
-V Input
-V Output
OV
+V Output
24 23
17 16 15 14 13
1 2
8 9 10 11 1 2
TO ORDER CALL 1-888-9-AIMTEC
AM1N-N Series
MODELS
Single output
AM1N-0505SH60-N
AM1N-0509SH60-N
AM1N-0512SH60-N
AM1N-0515SH60-N
AM1N-1205SH60-N
AM1N-1209SH60-N
AM1N-1212SH60-N
AM1N-1215SH60-N
AM1N-2405SH60-N
AM1N-2409SH60-N
AM1N-2412SH60-N
AM1N-2415SH60-N
Input Voltage
5V ± 10%
12V ± 10%
24V ± 10%
Ouput Voltage
Ouput Current max.
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
200mA
111mA
84mA
67mA
200mA
111mA
84mA
67mA
200mA
111mA
84mA
67mA
Ouput Voltage
Ouput Current max.
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
5VDC
9VDC
12VDC
15VDC
±100mA
±55mA
±42mA
±33mA
±100mA
±55mA
±42mA
±33mA
±100mA
±55mA
±42mA
±33mA
DC-DC CONVERTERS
Models
Dual output
Models
AM1N-0505DH60-N
AM1N-0509DH60-N
AM1N-0512DH60-N
AM1N-0515DH60-N
AM1N-1205DH60-N
AM1N-1209DH60-N
AM1N-1212DH60-N
AM1N-1215DH60-N
AM1N-2405DH60-N
AM1N-2409DH60-N
AM1N-2412DH60-N
AM1N-2415DH60-N
Input Voltage
5V ± 10%
12V ± 10%
24V ± 10%
TYPICAL CHARACTERISTICS
Continued on next page
VISIT US AT WWW.AIMTEC.CA
25
AM1N-N Series
APPLICATION NOTE
DC-DC CONVERTERS
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the dc/dc output end and input end to reduce the noise and
ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel
of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees the external capacitor table. To get an
extremely low ripple, an “LC” filtering network may be connected to the input and output ends of the dc/dc converter, which may produce a more significant
filtering effect. It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the dc/dc frequency
to avoid mutual interference (see figure 1).
Requirement on output load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of dc/dc converter in addition to a maximum load (namely
full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum output load is not less than 10% of the full load,
and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at
the output end in parallel to increase the load.
For single output
For dual output
Overload Protection
Under normal operating conditions, the output
circuit of these products has no protection
against over-current and short-circuits. The
simplest method is to connect a self-recovery
fuse in series at the input end or add a circuit
breaker to the circuit.
Output Voltage Regulation and
Over-voltage Protection Circuit
The simplest device for output voltage
regulation, over-voltage and over-current
protection is a linear voltage stabilizer with
overheat protection that is connected to the
input or output end in series (see Figure 2).
External Capacitor Table
for Single Output
External Capacitor Table
for Dual Output
Vin
External
Capacitor
Vout
External
Capacitor
Vin
External
Capacitor
Vout
External
Capacitor
5VDC
12VDC
24VDC
-
4.7uF
2.2uF
1uF
-
5VDC
9VDC
12VDC
15VDC
10uF
4.7uF
2.2uF
1uF
5VDC
12VDC
24VDC
-
4.7uF
2.2uF
1uF
-
5VDC
9VDC
12VDC
15VDC
4.7uF
2.2uF
1uF
0.47uF
26
TO ORDER CALL 1-888-9-AIMTEC
Similar pages