LED - Lamp ELD-810-345 15.11.2007 rev. 05 Radiation Type Technology Case Infrared DDH AlGaAs/AlGaAs 3 mm plastic lens Description High-power, high-speed infrared LED in standard 3 mm housing, small package allows compact design, housing with standoff leads 30,0 ±1,0 1,5 Note: Special packages without standoff available on request 2,5 Ø2,9 0,5 0,7 max 4,3 Applications 1,0 Ø3,1 0,65 4,0 1,0 Anode Optical communications, safety equipment, automation, optical sensors Maximum Ratings Tamb = 25°C, unless otherwise specified Parameter Test сonditions Symbol Value Unit IF 60 mA IFM 500 mA PD 120 mW Operating temperature range Tamb -20 to +85 °C Storage temperature range Tstg -30 to +100 °C Tj 100 °C Tsd 260 °C Typ Max Unit VF 1.5 1.8 V 1.6 Forward current (DC) Peak forward current (tP 10 µs, T = 10 ms) Power dissipation Junction temperature t ≤ 5 s, 3 mm from case Soldering temperature Optical and Electrical Characteristics Tamb = 25°C, unless otherwise specified Test Parameter conditions IF = 20 mA Forward voltage Symbol Min Forward voltage* IF = 50 mA VF Reverse voltage IR = 100 µA VF 5 Radiant power* IF = 20 mA Φe 6 8 mW Radiant power* IF = 50 mA Φe 14 18 mW Radiant intensity* IF = 50 mA Ιe 20 28 mW/sr Peak wavelength IF = 20 mA λp 800 810 Spectral bandwidth at 50% IF = 20 mA ∆λ0.5 30 nm Viewing angle IF = 20 mA 30 deg. Switching time IF = 20 mA ϕ tr, tf 40 ns V V 830 nm *measured after 30s current flow Note: All measurements carried out on EPIGAP equipment We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 1 of 3 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 LED - Lamp ELD-810-345 15.11.2007 rev. 05 Spectral power distribution (typical) at IF = 20 mA rel. Intensity (arb. units) 1,0 0,8 0,6 0,4 0,2 0,0 600 650 700 750 800 850 900 950 Wavelength (nm) We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 2 of 3 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 LED - Lamp ELD-810-345 15.11.2007 rev. 05 Remarks concerning optical radiation safety* Up to maximum forward current, at continuous operation, this LED may be classified as LED product Class 1 , according to standard IEC 60825-1:A2. Class 1 products are safe to eyes and skin under reasonably predictable conditions. This implicates a direct observation of the light beam by means of optical instruments. *Note: Safety classification of an optical component mainly depends on the intended application and the way the component is being used. Furthermore, all statements made to classification are based on calculations and are only valid for this LED "as it is", and at continuous operation. Using pulsed current or altering the light beam with additional optics may lead to different safety classifications. Therefore these remarks should be taken as recommendation and guideline only. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 3 of 3 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545