TI1 DAC101C081Q Dac101c08xx 10-bit micro power digital-to-analog converter with an i2c-compatible interface Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
DAC101C08xx 10-Bit Micro Power
Digital-to-Analog Converter With an I2C-Compatible Interface
1 Features
3 Description
•
•
•
•
The DAC101C081 device is a 10-bit, single channel,
voltage-output digital-to-analog converter (DAC) that
operates from a 2.7 V to 5.5 V supply. The output
amplifier allows rail-to-rail output swing and has an 6µsec settling time. The DAC101C081 uses the supply
voltage as the reference to provide the widest
dynamic output range and typically consumes 132 µA
while operating at 5.0 V. It is available in 6-lead SOT
and WSON packages and provides three address
options (pin selectable).
1
•
•
•
•
•
•
•
•
•
•
•
Ensured Monotonicity to 10-bits
Low Power Operation: 156-µA maximum at 3.3 V
Extended Power Supply Range (2.7 V to 5.5 V)
I2C-Compatible 2-Wire Interface Which Supports
Standard (100-kHz), Fast (400-kHz), and HighSpeed (3.4-MHz) Modes
Rail-to-Rail Voltage Output
Very Small Package
DAC101C081Q is AEC Q100 Grade 1 Qualified
and Manufactured on Automotive Grade Flow
Resolution: 10 Bits
INL: ±2 LSB (Maximum)
DNL: +0.3/-0.2 LSB (Maximum)
Setting Time: 6-µs (Maximum)
Zero Code Error: +10-mV (Maximum)
Full-Scale Error: −0.7 %FS (Maximum)
Supply Power (Normal): 380-µW (3-V) / 730-µW
(5-V) Typical
Supply Power (Power Down): 0.5-µW (3-V) / 0.9µW (5-V) Typical
As an alternative, the DAC101C085 provides nine
I2C™ addressing options and uses an external
reference. It has the same performance and settling
time as the DAC101C081 and is available in an 8lead VSSOP.
The DAC101C081 and DAC101C085 use a 2-wire,
I2C-compatible serial interface that operates in all
three speed modes, including high speed mode (3.4
MHz). An external address selection pin allows up to
three DAC101C081 or nine DAC101C085 devices
per 2-wire bus. Pin compatible alternatives to the
DAC101C081 are available that provide additional
address options.
Device Information(1)
2 Applications
•
•
•
•
•
•
PART NUMBER
Industrial Process Control
Portable Instruments
Digital Gain and Offset Adjustment
Programmable Voltage and Current Sources
Test Equipment
Automotive
PACKAGE
DAC101C081
BODY SIZE (NOM)
WSON (6)
2.20 mm × 2.50 mm
SOT (6)
1.60 mm × 2.90 mm
DAC101C085
VSSOP (8)
3.00 mm × 3.00 mm
DAC101C081Q
WSON (6)
2.20 mm × 2.50 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Block Diagram
VA*
VREF*
GND
DAC101C081 / DAC101C085
POWER-ON
RESET
REF
DAC
REGISTER
10 BIT DAC
VOUT
BUFFER
10
10
2.5k
100k
POWER-DOWN
CONTROL
LOGIC
2
I C
INTERFACE
* NOTE: ADR1 and VREF are for the DAC101C085 only. The DAC101C085 uses an external
reference (VREF), whereas, the DAC101C081 uses the supply (VA) as the reference.
ADR1* ADR0
SCL
SDA
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (continued).........................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
8.1
8.2
8.3
8.4
8.5
8.6
8.7
9
1
1
1
2
3
3
4
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings.............................................................. 5
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 6
Electrical Characteristics........................................... 6
AC and Timing Characteristics ................................. 8
Typical Characteristics ............................................ 11
Detailed Description ............................................ 14
9.1 Overview ................................................................. 14
9.2 Functional Block Diagram ....................................... 14
9.3 Feature Description................................................. 14
9.4 Device Functional Modes........................................ 16
9.5 Programming........................................................... 17
9.6 Registers ................................................................. 20
10 Application and Implementation........................ 21
10.1 Application Information.......................................... 21
10.2 Typical Application ............................................... 23
11 Power Supply Recommendations ..................... 25
11.1
Using References as Power Supplies ................. 25
12 Layout................................................................... 28
12.1 Layout Guidelines ................................................ 28
12.2 Layout Example .................................................... 28
13 Device and Documentation Support ................. 29
13.1
13.2
13.3
13.4
13.5
13.6
Device Support......................................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
29
30
30
30
30
30
14 Mechanical, Packaging, and Orderable
Information ........................................................... 30
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (March 2013) to Revision B
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................ 1
•
Added addresses that the DAC responds to on the I2C bus. .............................................................................................. 19
Changes from Original (March 2013) to Revision A
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 28
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
5 Description (continued)
The DAC101C081 and DAC101C085 each have a 16-bit register that controls the mode of operation, the powerdown condition, and the output voltage. A power-on reset circuit ensures that the DAC output powers up to zero
volts. A power-down feature reduces power consumption to less than a microWatt. Their low power consumption
and small packages make these DACs an excellent choice for use in battery operated equipment. Each DAC
operates over the extended industrial temperature range of −40°C to +125°C.
The DAC101C081 and DAC101C085 are each part of a family of pin compatible DACs that also provide 12 and
8 bit resolution. For 12-bit DACs see the DAC121C081 and DAC121C085. For 8-bit DACs see the DAC081C081
and DAC081C085.
6 Device Comparison Table (1)
(1)
Resolution
SOT-6 and WSON-6 Packages
12-bit
DAC121C081
VSSOP-8 Package w/ External Reference
DAC121C085
10-bit
DAC101C081
DAC101C085
8-bit
DAC081C081
DAC081C085
All devices are fully pin and function compatible.
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
3
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
7 Pin Configuration and Functions
NGF Package
6-Pin WSON
Top View
ADR0 1
SCL
SDA
DDC Package
6-Lead SOT
Top View
6
VOUT
2 WSON 5
VA
3
GND
4
VOUT
1
VA
2
GND
3
DAC101C081
SOT
6
ADR0
5
SCL
4
SDA
DAC101C081
DGK Package
8-Lead VSSOP
Top View
ADR0
1
ADR1
2
8
VOUT
7
VREF
VSSOP
SCL
3
6
VA
SDA
4
5
GND
DAC101C085
Pin Functions
PIN
NAME
WSON
SOT
VSSOP
ADR0
1
6
1
EQUIVALENT
CIRCUIT
TYPE
Digital Input,
three levels
V+
PIN
Snap
Back
D1
41.5k
2.1k
DESCRIPTION
Tri-state Address Selection Input. Sets the two
Least Significant Bits (A1 and A0) of the 7-bit slave
address. (see Table 1)
41.5k
ADR1
—
—
2
Digital Input,
three levels
Tri-State Address Selection Input. Sets Bits A6 and
A3 of the 7-bit slave address. (see Table 1)
GND
4
3
5
Ground
Ground for all on-chip circuitry
PAD
PAD
—
—
Ground
Exposed die attach pad can be connected to
ground or left floating. Soldering the pad to the PCB
offers optimal thermal performance and enhances
package self-alignment during reflow.
SCL
2
5
3
Digital Input
GND
Serial Clock Input. SCL is used together with SDA
to control the transfer of data in and out of the
device.
PIN
Snap
Back
SDA
3
4
4
Digital
Input/Output
VA
5
2
6
Supply
VOUT
6
1
8
Analog Output
VREF
—
—
7
Supply
4
Submit Documentation Feedback
D1
GND
Serial Data bi-directional connection. Data is
clocked into or out of the internal 16-bit register
relative to the clock edges of SCL. This is an open
drain data line that must be pulled to the supply
(VA) by an external pullup resistor.
Power supply input. For the SOT and WSON
versions, this supply is used as the reference. Must
be decoupled to GND.
Analog Output Voltage
Unbufferred reference voltage. For the VSSOP-8,
this supply is used as the reference. VREF must be
free of noise and decoupled to GND.
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
8 Specifications
8.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1) (2) (3)
MIN
MAX
UNIT
Supply voltage, VA
−0.3
6.5
V
Voltage on any input pin
−0.3
Input current at any pin (4)
Package input current (4)
Power consumption at TA = 25°C
See
(1)
(2)
(3)
(4)
(5)
V
mA
±20
mA
150
°C
150
°C
(5)
Operating junction temperature
−65
Storage temperature, Tstg
6.5
±10
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are measured with respect to GND = 0 V, unless otherwise specified.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
When the input voltage at any pin exceeds 5.5 V or is less than GND, the current at that pin should be limited to 10 mA. The 20 mA
maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10
mA to two.
The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by
TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula
PDMAX = (TJmax − TA) / θJA. The values for maximum power dissipation will be reached only when the device is operated in a severe
fault condition (e.g., when input or output pins are driven beyond the operating ratings, or the power supply polarity is reversed).
8.2 ESD Ratings
VALUE
UNIT
DAC081C081 in NGF Package
Human-body model (HBM), per
ANSI/ESDA/JEDEC JS-001
V(ESD)
Electrostatic discharge
All pins except 2 and 3
±2500
Pins 2 and 3
±5000
Charged-device model (CDM), per JEDEC All pins except 2 and 3
specification JESD22-C101
Pins 2 and 3
±1000
All pins except 2 and 3
±250
Pins 2 and 3
±350
All pins except 4 and 5
±2500
Pins 4 and 5
±5000
Machine model (MM)
±1000
V
DAC081C081 in DDC Package
Human-body model (HBM), per
ANSI/ESDA/JEDEC JS-001
V(ESD)
Electrostatic discharge
Charged-device model (CDM), per JEDEC All pins except 4 and 5
specification JESD22-C101
Pins 4 and 5
±1000
All pins except 4 and 5
±250
Pins 4 and 5
±350
All pins except 3 and 4
±2500
Pins 3 and 4
±5000
Machine model (MM)
±1000
V
DAC081C085 in DGK Package
Human-body model (HBM), per
ANSI/ESDA/JEDEC JS-001
V(ESD)
Electrostatic discharge
Charged-device model (CDM), per JEDEC All pins except 3 and 4
specification JESD22-C101
Pins 3 and 4
±1000
All pins except 3 and 4
±250
Pins 3 and 4
±350
Machine model (MM)
Copyright © 2012–2016, Texas Instruments Incorporated
±1000
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
V
5
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
8.3 Recommended Operating Conditions
(1)
See
MIN
NOM
MAX
UNIT
Operating temperature range
−40
TA
125
°C
Supply voltage, VA
2.7
5.5
V
Reference voltage, VREFIN
1
VA
V
Digital input voltage (2) (3)
0
5.5
V
Output load
0
1500
pF
(1)
(2)
(3)
All voltages are measured with respect to GND = 0 V, unless otherwise specified.
The inputs are protected as shown below. Input voltage magnitudes up to 5.5 V, regardless of VA, will not cause errors in the conversion
result. For example, if VA is 3 V, the digital input pins can be driven with a 5 V logic device.
To ensure accuracy, it is required that VA and VREF be well bypassed.
8.4 Thermal Information
THERMAL METRIC
RθJA
(1)
(2)
(3)
DAC101C081
DAC101C081,
DAC101C081Q
DAC101C085
DDC (SOT)
NGF (WSON)
DGK (VSSOP)
6 PINS
6 PINS
8 PINS
250
190
240
(1) (2) (3)
Junction-to-ambient thermal resistance
UNIT
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging.
Reflow temperature profiles are different for lead-free packages.
8.5 Electrical Characteristics
The following specifications apply for VA = 2.7 V to 5.5 V, VREF = VA, CL = 200 pF to GND, input code range 12 to 1011. All
Maximum and Minimum limits apply for TMIN ≤ TA ≤ TMAX and all Typical limits are at TA = 25°C (unless otherwise specified).
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX (1)
UNIT
STATIC PERFORMANCE
INL
Resolution
10
Monotonicity
10
Bits
Bits
+0.6
Integral non-linearity
−2
+2
−0.4
+0.12
LSB
LSB
+0.3
LSB
DNL
Differential non-linearity
ZE
Zero code error
IOUT = 0
+1.1
+10
mV
FSE
Full-scale error
IOUT = 0
−0.1
−0.7
%FSR
GE
Gain error
All ones loaded to DAC register
−0.2
−0.7
%FSR
ZCED
Zero code error drift
TC GE
−0.2
−0.04
LSB
−20
µV/°C
VA = 3 V
−0.7
ppm
FSR/°C
VA = 5 V
−1
ppm
FSR/°C
Gain error tempco
ANALOG OUTPUT CHARACTERISTICS (VOUT)
Output voltage range (2)
ZCO
FSO
(1)
(2)
6
Zero code output
Full scale output
DAC101C085
0
VREF
V
DAC101C081
0
VA
V
VA = 3 V, IOUT = 200 µA
1.3
mV
VA = 5 V, IOUT = 200 µA
7.0
mV
VA = 3 V, IOUT = 200 µA
2.984
V
VA = 5 V, IOUT = 200 µA
4.989
V
Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing
Quality Level).
This parameter is ensured by design and/or characterization and is not tested in production.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
Electrical Characteristics (continued)
The following specifications apply for VA = 2.7 V to 5.5 V, VREF = VA, CL = 200 pF to GND, input code range 12 to 1011. All
Maximum and Minimum limits apply for TMIN ≤ TA ≤ TMAX and all Typical limits are at TA = 25°C (unless otherwise specified).
PARAMETER
TEST CONDITIONS
Output short circuit current
(ISOURCE)
IOS
Output short circuit current
(ISINK)
IOS
IO
Continuous output
current (2)
CL
Maximum load capacitance
ZOUT
DC output impedance
MIN
TYP (1)
MAX (1)
UNIT
VA = 3 V, VOUT = 0 V,
Input code = FFFh.
56
mA
VA = 5 V, VOUT = 0 V,
Input code = FFFh.
69
mA
VA = 3 V, VOUT = 3 V,
Input code = 000h.
−52
mA
VA = 5 V, VOUT = 5 V,
Input code = 000h.
−75
mA
Available on the DAC output
11
mA
RL = ∞
1500
pF
RL = 2 kΩ
1500
pF
7.5
Ω
0.2
V
REFERENCE INPUT CHARACTERISTICS- (DAC101C085 only)
Input range inimum
VREF
1
Input range maximum
VA
Input impedance
120
V
kΩ
LOGIC INPUT CHARACTERISTICS (SCL, SDA)
VIH
Input high voltage
VIL
Input low voltage
IIN
Input current
CIN
Input pin capacitance (2)
VHYST
Input hysteresis
0.7 × VA
V
0.3 × VA
V
±1
µA
3
pF
0.1 × VA
V
VA– 0.5
V
LOGIC INPUT CHARACTERISTICS (ADR0, ADR1)
VIH
Input high voltage
VIL
Input low voltage
0.5
V
IIN
Input current
±1
µA
ISINK = 3 mA
0.4
V
ISINK = 6 mA
0.6
V
±1
µA
LOGIC OUTPUT CHARACTERISTICS (SDA)
VOL
Output low voltage
IOZ
High-impedence output
leakage current
POWER REQUIREMENTS
VA
Supply voltage minimum
2.7
V
Supply voltage maximum
5.5
V
Normal -- VOUT set to midscale. 2-wire interface quiet (SCL = SDA = VA). (output unloaded)
IST_VA-1
IST_VA-5
VADAC101C081 supply current
VADAC101C085 supply current
VA = 2.7 V to 3.6 V
105
156
µA
VA = 4.5 V to 5.5 V
132
214
µA
VA = 2.7 V to 3.6 V
86
118
µA
VA = 4.5 V to 5.5 V
98
152
µA
37
43
µA
VA = 4.5 V to 5.5 V
53
61
µA
IST_VREF
VREF supply current
(DAC101C085 only)
VA = 2.7 V to 3.6 V
PST
Power consumption
(VA & VREF for DAC101C085)
VA = 3 V
380
µW
VA = 5 V
730
µW
Continuous Operation -- 2-wire interface actively addressing the DAC and writing to the DAC register. (output unloaded)
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
7
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Electrical Characteristics (continued)
The following specifications apply for VA = 2.7 V to 5.5 V, VREF = VA, CL = 200 pF to GND, input code range 12 to 1011. All
Maximum and Minimum limits apply for TMIN ≤ TA ≤ TMAX and all Typical limits are at TA = 25°C (unless otherwise specified).
PARAMETER
fSCL = 400 kHz
ICO_VA-1
VADAC101C081 supply current
fSCL = 3.4 MHz
fSCL = 400 kHz
ICO_VA-5
VADAC101C085 supply current
fSCL = 3.4 MHz
ICO_VREF
VREF supply current
(DAC101C085 only)
fSCL = 400 kHz
PCO
TYP (1)
MAX (1)
VA = 2.7 V to
3.6 V
134
220
µA
VA = 4.5 V to
5.5 V
192
300
µA
VA = 2.7 V to
3.6 V
225
320
µA
VA = 4.5 V to
5.5 V
374
500
µA
VA = 2.7 V to
3.6 V
101
155
µA
VA = 4.5 V to
5.5 V
142
220
µA
VA = 2.7 V to
3.6 V
193
235
µA
VA = 4.5 V to
5.5 V
325
410
µA
VA = 2.7 V to
3.6 V
33.5
55
µA
VA = 4.5 V to
5.5 V
49.5
71.4
µA
TEST CONDITIONS
Power consumption
(VA & VREF for DAC101C085)
fSCL = 3.4 MHz
MIN
UNIT
VA = 3 V
480
µW
VA = 5 V
1.06
mW
VA = 3 V
810
µW
VA = 5 V
2.06
mW
Power Down -- 2-wire interface quiet (SCL = SDA = VA) after PD mode written to DAC register. (output unloaded)
IPD
PPD
Supply current
(VA & VREF for DAC101C085)
All power-down
modes
Power consumption
(VA & VREF for DAC101C085)
All power-down
modes
VA = 2.7 V to
3.6 V
0.13
1.52
µA
VA = 4.5 V to
5.5 V
0.15
3.25
µA
VA = 3 V
0.5
µW
VA = 5 V
0.9
µW
8.6 AC and Timing Characteristics
The following specifications apply for VA = 2.7 V to 5.5 V, VREF = VA, RL = Infinity, CL = 200 pF to GND. All Maximum and
Minimum limits apply for TMIN ≤ TA ≤ TMAX and all Typical limits are at TA = 25°C (unless otherwise specified).
TEST CONDITIONS (1)
PARAMETER
ts
Output voltage settling time (4)
SR
Output slew rate
Glitch impulse
TYP (2)
MAX (1) (3)
100h to 300h code change
RL = 2 kΩ, CL = 200 pF
4.5
6
1
V/µs
Code change from 200h to 1FFh
12
nV-sec
MIN
Digital feedthrough
Multiplying bandwidth (5)
Total harmonic distortion
(1)
(2)
(3)
(4)
(5)
8
VREF = 2.5 V ± 0.1 Vpp
(5)
VREF = 2.5 V ± 0.1 Vpp
input frequency = 10 kHz
UNIT
µs
0.5
nV-sec
160
kHz
70
dB
Cb refers to the capacitance of one bus line. Cb is expressed in pF units.
Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing
Quality Level).
Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing
Quality Level).
This parameter is ensured by design and/or characterization and is not tested in production.
Applies to the Multiplying DAC configuration. In this configuration, the reference is used as the analog input. The value loaded in the
DAC Register will digitally attenuate the signal at Vout.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
AC and Timing Characteristics (continued)
The following specifications apply for VA = 2.7 V to 5.5 V, VREF = VA, RL = Infinity, CL = 200 pF to GND. All Maximum and
Minimum limits apply for TMIN ≤ TA ≤ TMAX and all Typical limits are at TA = 25°C (unless otherwise specified).
TEST CONDITIONS (1)
PARAMETER
tWU
Wake-up time
TYP (2)
MIN
MAX (1) (3)
UNIT
VA = 3 V
0.8
µsec
VA = 5 V
0.5
µsec
DIGITAL TIMING SPECS (SCL, SDA)
fSCL
tLOW
Serial clock frequency
SCL low time
Standard mode
100
Fast mode
400
High speed mode, Cb = 100 pF
3.4
High speed mode, Cb = 400 pF
1.7
Standard mode
4.7
Fast mode
1.3
High speed mode, Cb = 100 pF
160
High speed mode, Cb = 400 pF
320
Standard mode
tHIGH
tSU;DAT
SCL high time
Data set-up time
tHD;DAT
tSU;STA
Data hold time
Set-up time for a start or a
repeated start condition
0.6
High speed mode, Cb = 100 pF
60
High speed mode, Cb = 400 pF
120
Standard mode
250
Fast mode
100
tHD;STA
tBUF
Hold time for a start or a
repeated start condition
Bus free time between a stop
and start condition
Set-up time for a stop condition
ns
µs
ns
ns
10
0
3.45
Fast mode
0
0.9
High speed mode, Cb = 100 pF
0
70
High speed mode, Cb = 400 pF
0
150
Standard mode
4.7
Fast mode
0.6
High speed mode
160
0.6
High speed mode
160
Standard mode
4.7
Fast mode
1.3
0.6
High speed mode
160
µs
ns
µs
µs
ns
Standard mode
trDA
Rise time of SDA signal
Fast mode
Fall time of SDA signal
Rise time of SCL signal
ns
20 + 0.1Cb
300
ns
10
80
ns
High speed mode, Cb = 400 pF
20
160
ns
250
ns
Fast mode
20 + 0.1Cb
250
ns
High speed mode, Cb = 100 pF
10
80
ns
High speed mode, Cb = 400 pF
20
160
ns
Standard mode
trCL
1000
High speed mode, Cb = 100 pF
Standard mode
tfDA
ns
ns
4
Fast mode
µs
µs
4
Fast mode
Standard mode
tSU;STO
µs
Standard mode
Standard mode
MHz
4
Fast mode
High speed mode
kHz
1000
ns
20 + 0.1Cb
300
ns
High speed mode, Cb = 100 pF
10
40
ns
High speed mode, Cb = 400 pF
20
80
ns
Fast mode
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
9
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
AC and Timing Characteristics (continued)
The following specifications apply for VA = 2.7 V to 5.5 V, VREF = VA, RL = Infinity, CL = 200 pF to GND. All Maximum and
Minimum limits apply for TMIN ≤ TA ≤ TMAX and all Typical limits are at TA = 25°C (unless otherwise specified).
TEST CONDITIONS (1)
PARAMETER
TYP (2)
MIN
Standard mode
trCL1
Rise time of SCL signal after a
Fast mode
repeated start condition and after
High speed mode, Cb = 100 pF
an acknowledge bit.
High speed mode, Cb = 400 pF
ns
20 + 0.1Cb
300
ns
10
80
ns
20
160
ns
300
ns
20 + 0.1Cb
300
ns
High speed mode, Cb = 100 pF
10
40
ns
High speed mode, Cb = 400 pF
20
80
ns
400
pF
Fast mode
Fall time of a SCL signal
Cb
Capacitive load for each bus line
(SCL and SDA)
tSP
Pulse width of spike
suppressed (6) (4)
Fast mode
50
High speed mode
10
toutz
SDA output delay (see Section
1.9)
Fast mode
87
270
High speed mode
38
60
(6)
UNIT
1000
Standard mode
tfCL
MAX (1) (3)
ns
ns
Spike suppression filtering on SCL and SDA will supress spikes that are less than 50ns for standard-fast mode and less than 10ns for
hs-mode.
FSE
1023 x VREF
1024
GE = FSE - ZE
FSE = GE + ZE
OUTPUT
VOLTAGE
ZE
0
0
1023
DIGITAL INPUT CODE
Figure 1. Input / Output Transfer Characteristic
SDA
tLOW
tf
tr
tHD;STA
tr
tf
tBUF
tSP
SCL
tSU;STA
tHD;STA
tHD;DAT
START
tHIGH
tSU;STO
tSU;DAT
STOP
REPEATED
START
START
Figure 2. Serial Timing Diagram
10
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
8.7 Typical Characteristics
VREF = VA, fSCL = 3.4 MHz, TA = 25°C, input code range 12 to 1011 (unless otherwise stated).
Figure 3. Define (INL)
Figure 4. Define (DNL)
Figure 5. INL/DNL vs Temperature at VA = 3.0 V
Figure 6. INL/DNL vs Temperature at VA = 5 V
Figure 7. INL/DNL vs VREFIN at VA = 3 V
Figure 8. INL/DNL vs VREFIN at VA = 5 V
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
11
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Typical Characteristics (continued)
VREF = VA, fSCL = 3.4 MHz, TA = 25°C, input code range 12 to 1011 (unless otherwise stated).
12
Figure 9. INL/DNL vs VA
Figure 10. Zero Code Error vs VA
Figure 11. Zero Code Error vs Temperature
Figure 12. Full Scale Error vs VA
Figure 13. Full Scale Error vs Temperature
Figure 14. Total Supply Current vs VA
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
Typical Characteristics (continued)
VREF = VA, fSCL = 3.4 MHz, TA = 25°C, input code range 12 to 1011 (unless otherwise stated).
Figure 15. VREF Supply Current vs VA
Figure 16. Total Supply Current
vs Temperature at VA = 3 V
Figure 17. Total Supply Current
vs Temperature at VA = 5 V
Figure 18. 5 V Glitch Response
Figure 19. Power-On Reset
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
13
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
9 Detailed Description
9.1 Overview
The DAC101C081 is fabricated on a CMOS process with an architecture that consists of switches and resistor
strings that are followed by an output buffer.
9.2 Functional Block Diagram
VA*
VREF*
GND
DAC101C081 / DAC101C085
POWER-ON
RESET
REF
DAC
REGISTER
10 BIT DAC
VOUT
BUFFER
10
10
2.5k
100k
POWER-DOWN
CONTROL
LOGIC
2
I C
INTERFACE
* NOTE: ADR1 and VREF are for the DAC101C085 only. The DAC101C085 uses an external
reference (VREF), whereas, the DAC101C081 uses the supply (VA) as the reference.
ADR1* ADR0
SCL
SDA
9.3 Feature Description
9.3.1 DAC Section
For simplicity, a single resistor string is shown in Figure 20. This string consists of 1024 equal valued resistors
with a switch at each junction of two resistors, plus a switch to ground. The code loaded into the DAC register
determines which switch is closed, connecting the proper node to the amplifier. The input coding is straight
binary with an ideal output voltage of:
VOUT = VREF × (D / 1024)
where D is the decimal equivalent of the binary code that is loaded into the DAC register. D can take on
any integer value between 0 and1023. This configuration ensures that the DAC is monotonic.
(1)
14
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
Feature Description (continued)
VREF
R
R
R
To Output Amplifier
R
R
Figure 20. DAC Resistor String
9.3.2 Output Amplifier
The output amplifier is rail-to-rail, providing an output voltage range of 0 V to VA when the reference is VA. All
amplifiers, even rail-to-rail types, exhibit a loss of linearity as the output approaches the supply rails (0 V and VA,
in this case). For this reason, linearity is specified over less than the full output range of the DAC. However, if the
reference is less than VA, there is only a loss in linearity in the lowest codes. The output capabilities of the
amplifier are described in the Electrical Characteristics table.
The output amplifiers are capable of driving a load of 2-kΩ in parallel with 1500 pF to ground or to VA. The zerocode and full-scale outputs for given load currents are available in the Electrical Characteristics table.
9.3.3
Reference Voltage
The DAC101C081 uses the supply (VA) as the reference. With that said, VA must be treated as a reference. The
Analog output will only be as clean as the reference (VA). It is recommended that the reference be driven by a
voltage source with low output impedance.
The DAC101C085 comes with an external reference supply pin (VREF). For the DAC101C085, it is important that
VREF be kept as clean as possible.
The Applications Information section describes a handful of ways to drive the reference appropriately. Refer to
Using References as Power Supplies for details.
9.3.4
Power-On Reset
The power-on reset circuit controls the output voltage of the DAC during power-up. Upon application of power,
the DAC register is filled with zeros and the output voltage is 0 Volts. The output remains at 0 V until a valid write
sequence is made to the DAC.
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
15
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Feature Description (continued)
When resetting the device, it is crutial that the VA supply be lowered to a maximum of 200mV before the supply
is raised again to power-up the device. Dropping the supply to within 200mV of GND during a reset will ensure
the ADC performs as specified.
9.3.5 Simultaneous Reset
The broadcast address allows the I2C™ master to write a single word to multiple DACs simultaneously. Provided
that all of the DACs exist on a singleI2C™ bus, every DAC will update when the broadcast address is used to
address the bus. This feature allows the master to reset all of the DACs on a shared I2C™ bus to a specific
digital code. For instance, if the master writes a power-down code to the bus with the broadcast address, all of
the DACs will power-down simultaneously.
9.3.6 Additional Timing Information: toutz
The toutz specification is provided to aid the design of the I2C bus. After the SCL bus is driven low by the I2C™
master, the SDA bus will be held for a short time by the DAC101C081. This time is referred to as toutz. The
following figure illustrates the relationship between the fall of SCL, at the 30% threshold, to the time when the
DAC begins to transition the SDA bus. The toutz specification only applies when the DAC is in control of the SDA
bus. The DAC is only in control of the bus during an ACK by the DAC101C081 or a data byte read from the DAC
(see Figure 25).
SCL
SDA
toutz
Figure 21. Data Output Timing
The toutz specification is typically 87nsec in Standard-Fast Mode and 38nsec in Hs-Mode.
9.4 Device Functional Modes
9.4.1 Power-Down Modes
The DAC101C081 has three power-down modes. In power-down mode, the supply current drops to 0.13µA at 3
V and 0.15µA at 5 V (typ). The DAC101C081 is put into power-down mode by writing a one to PD1 and/or PD0.
The outputs can be set to high impedance, terminated by 2.5 kΩ to GND, or terminated by 100 kΩ to GND (see
Figure 26).
The bias generator, output amplifier, resistor string, and other linear circuitry are all shut down in any of the
power-down modes. When the DAC101C081 is powered down, the value written to the DAC register, including
the power-down bits, is saved. While the DAC is in power-down, the saved DAC register contents can be read
back. When the DAC is brought out of power-down mode, the DAC register contents will be overwritten and VOUT
will be updated with the new 10-bit data value.
The time to exit power-down (Wake-Up Time) is typically 0.8µsec at 3 V and 0.5µsec at 5 V.
16
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
9.5 Programming
9.5.1 Serial Interface
The I2C™-compatible interface operates in all three speed modes. Standard mode (100kHz) and Fast mode (400
kHz) are functionally the same and will be referred to as Standard-Fast mode in this document. High-Speed
mode (3.4 MHz) is an extension of Standard-Fast mode and will be referred to as Hs-mode in this document.
The following diagrams describe the timing relationships of the clock (SCL) and data (SDA) signals. Pullup
resistors or current sources are required on the SCL and SDA busses to pull them high when they are not being
driven low. A logic zero is transmitted by driving the output low. A logic high is transmitted by releasing the output
and allowing it to be pulled-up externally. The appropriate pullup resistor values will depend upon the total bus
capacitance and operating speed.
9.5.2 Basic I2C™ Protocol
The I2C™ interface is bi-directional and allows multiple devices to operate on the same bus. To facilitate this bus
configuration, each device has a unique hardware address which is referred to as the "slave address." To
communicate with a particular device on the bus, the controller (master) sends the slave address and listens for
a response from the slave. This response is referred to as an acknowledge bit. If a slave on the bus is addressed
correctly, it Acknowledges (ACKs) the master by driving the SDA bus low. If the address doesn't match a
device's slave address, it Not-acknowledges (NACKs) the master by letting SDA be pulled high. ACKs also occur
on the bus when data is being transmitted. When the master is writing data, the slave ACKs after every data byte
is successfully received. When the master is reading data, the master ACKs after every data byte is received to
let the slave know it wants to receive another data byte. When the master wants to stop reading, it NACKs after
the last data byte and creates a Stop condition on the bus.
All communication on the bus begins with either a Start condition or a Repeated Start condition. The protocol for
starting the bus varies between Standard-Fast mode and Hs-mode. In Standard-Fast mode, the master
generates a Start condition by driving SDA from high to low while SCL is high. In Hs-mode, starting the bus is
more complicated. Please refer to High-Speed (Hs) Mode for the full details of a Hs-mode Start condition. A
Repeated Start is generated to either address a different device, or switch between read and write modes. The
master generates a Repeated Start condition by driving SDA low while SCL is high. Following the Repeated
Start, the master sends out the slave address and a read/write bit as shown in Figure 22. The bus continues to
operate in the same speed mode as before the Repeated Start condition.
All communication on the bus ends with a Stop condition. In either Standard-Fast mode or Hs-Mode, a Stop
condition occurs when SDA is pulled from low to high while SCL is high. After a Stop condition, the bus remains
idle until a master generates a Start condition.
Please refer to the PhilipsI2C™ Specification (Version 2.1 Jan, 2000) for a detailed description of the serial
interface.
SDA
1
2
MSB
R/W
Direction
Bit
Acknowledge
from the Device
7-bit Slave Address
SCL
ACK
LSB
MSB
6
7
8
9
LSB
N/ACK
Data Byte
*Acknowledge
or Not-ACK
1
8
2
9
Repeated for the Lower Data Byte
and Additional Data Transfers
START or
REPEATED
START
STOP
*Note: In continuous mode, this bit must be an ACK from
the data receiver. Immediately preceding a STOP
condition, this bit must be a NACK from the master.
Figure 22. Basic Operation
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
17
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Programming (continued)
9.5.3 Standard-Fast Mode
In Standard-Fast mode, the master generates a start condition by driving SDA from high to low while SCL is
high. The Start condition is always followed by a 7-bit slave address and a Read/Write bit. After these eight bits
have been transmitted by the master, SDA is released by the master and the DAC101C081 either ACKs or
NACKs the address. If the slave address matches, the DAC101C081 ACKs the master. If the address doesn't
match, the DAC101C081 NACKs the master.
For a write operation, the master follows the ACK by sending the upper eight data bits to the DAC101C081.
Then the DAC101C081 ACKs the transfer by driving SDA low. Next, the lower eight data bits are sent by the
master. The DAC101C081 then ACKs the transfer. At this point, the DAC output updates to reflect the contents
of the 16-bit DAC register. Next, the master either sends another pair of data bytes, generates a Stop condition
to end communication, or generates a Repeated Start condition to communicate with another device on the bus.
For a read operation, the DAC101C081 sends out the upper eight data bits of the DAC register. This is followed
by an ACK by the master. Next, the lower eight data bits of the DAC register are sent to the master. The master
then produces a NACK by letting SDA be pulled high. The NACK is followed by a master-generated Stop
condition to end communication on the bus, or a Repeated Start to communicate with another device on the bus.
9.5.4 High-Speed (Hs) Mode
For Hs-mode, the sequence of events to begin communication differ slightly from Standard-Fast mode. Figure 23
describes this in further detail. Initially, the bus begins running in Standard-Fast mode. The master generates a
Start condition and sends the 8-bit Hs master code (00001XXX) to the DAC101C081. Next, the DAC101C081
responds with a NACK. Once the SCL line has been pulled to a high level, the master switches to Hs-mode by
increasing the bus speed and generating a Repeated Start condition (driving SDA low while SCL is pulled high).
At this point, the master sends the slave address to the DAC101C081, and communication continues as shown
above in the "Basic Operation" Diagram (see Figure 22).
When the master generates a Repeated Start condition while in Hs-mode, the bus stays in Hs-mode awaiting the
slave address from the master. The bus continues to run in Hs-mode until a Stop condition is generated by the
master. When the master generates a Stop condition on the bus, the bus must be started in Standard-Fast mode
again before increasing the bus speed and switching to Hs-mode.
SDA
NACK
MSB
8-ELW 0DVWHU FRGH ³00001[[[´
7-bit Slave
Address
Not-Acknowledge
from the Device
1
SCL
2
5
6
7
8
9
1
2
Repeated
START
START
Standard-Fast Mode
Hs-Mode
Figure 23. Beginning Hs-Mode Communication
18
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
Programming (continued)
9.5.5 I2C Slave (Hardware) Address
The DAC has a seven-bit I2C™ slave address. For the VSSOP-8 version of the DAC, this address is configured
by the ADR0 and ADR1 address selection inputs. For the DAC101C081, the address is configured by the ADR0
address selection input. ADR0 and ADR1 can be grounded, left floating, or tied to VA. If desired, the address
selection inputs can be set to VA/2 rather than left floating. The state of these inputs sets the address the DAC
responds to on the I2C™ bus (see Table 1). In addition to the selectable slave address, there is also a broadcast
address (1001000) for all DAC101C081's and DAC101C085's on the 2-wire bus. When the bus is addressed by
the broadcast address, all the DAC101C081's and DAC101C085's will respond and update synchronously.
Figure 24 and Figure 25 describe how the master device should address the DAC via the I2C™-Compatible
interface.
Keep in mind that the address selection inputs (ADR0 and ADR1) are only sampled until the DAC is correctly
addressed with a non-broadcast address. At this point, the ADR0 and ADR1 inputs Tri-State and the slave
address is "locked". Changes to ADR0 and ADR1 will not update the selected slave address until the device is
power-cycled.
Table 1. Slave Addresses
ADR1
ADR0
ADR0
0001100, 1000110
Floating
Floating
Floating
0001101, 1000110
Floating
GND
GND
0001110, 1000111
Floating
VA
VA
0001000, 1000100
GND
Floating
—
0001001, 1000100
GND
GND
—
0001010, 1000101
GND
VA
—
1001100, 1100110
VA
Floating
—
1001101, 1100110
VA
GND
—
1001110, 1100111
VA
VA
—
1001000, 1100100
(1)
DAC101C081 (SOT &
WSON) (1)
DAC101C085 (VSSOP-8)
SLAVE ADDRESS
[A6 - A0]
Broadcast Address
Pin-compatible alternatives to the DAC101C081 options are available with additional address options.
9.5.6 Writing to the DAC Register
To write to the DAC, the master addresses the part with the correct slave address (A6-A0) and writes a "zero" to
the read/write bit. If addressed correctly, the DAC returns an ACK to the master. The master then sends out the
upper data byte. The DAC responds by sending an ACK to the master. Next, the master sends the lower data
byte to the DAC. The DAC responds by sending an ACK again. At this point, the master either sends the upper
byte of the next data word to be converted by the DAC, generates a Stop condition to end communication, or
generates a Repeated Start condition to begin communication with another device on the bus. Until generating a
Stop condition, the master can continuously write the upper and lower data bytes to the DAC register. This
allows for a maximum DAC conversion rate of 188.9 kilo-conversions per second in Hs-mode.
1
9
1
9
1
9
SCL
SDA
A6
Start by
Master
A5
A4
A3
A2
A1
Frame 1
Address Byte
from Master
A0 R/W
0
ACK
by
DAC101C081
0
PD1 PD0 D11 D10 D9
Frame 2
Data Byte from
Master
D7
ACK
by
DAC101C081
D8
D6
D5
D4
D3
D2
Frame 3
Data Byte from
Master
D1
D0
ACK Stop by
by
Master
DAC101C081
Repeat Frames
2 and 3 for
Continuous Mode
Figure 24. Typical Write to the DAC Register
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
19
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
9.5.7 Reading from the DAC Register
To read from the DAC register, the master addresses the part with the correct slave address (A6-A0) and writes
a "one" to the read/write bit. If addressed correctly, the DAC returns an ACK to the master. Next, the DAC sends
out the upper data byte. The master responds by sending an ACK to the DAC to indicate that it wants to receive
another data byte. Then the DAC sends the lower data byte to the master. Assuming only one 16-bit data word is
read, the master sends a NACK after receiving the lower data byte. At this point, the master either generates a
Stop condition to end communication, or a Repeated Start condition to begin communication with another device
on the bus.
1
9
1
9
1
9
SCL
SDA
A6
A5
A4
A3
A2
A1
A0 R/W
0
ACK
by
DAC101C081
Start by
Master
Frame 1
Address Byte
from Master
0
PD1 PD0 D11 D10 D9
Frame 2
Data Byte from
DAC101C081
D8
D7
D6
D5
ACK
by
Master
D4
D3
D2
Frame 3
Data Byte from
DAC101C081
D1
D0
NACK
by
Master
Stop by
Master
Figure 25. Typical Read from the DAC Register
9.6 Registers
9.6.1 DAC Register
The DAC register, Figure 26, has sixteen bits. The first two bits are always zero. The next two bits determine the
mode of operation (normal mode or one of three power-down modes). The final twelve bits of the shift register
are the data bits. The data format is straight binary (MSB first, LSB last), with twelve 0's corresponding to an
output of 0 V and twelve 1's corresponding to a full-scale output of VA - 1 LSB. When writing to the DAC
Register, VOUT will update on the rising edge of the ACK following the lower data byte.
LSB
MSB
X
X PD1 PD0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
0
0
DATA BITS
0
0
1
1
0
1
0
1
Normal Operation.
2.5 kÖ to GND.
100 kÖ to GND.
High Impedance.
Power-Down Modes
Figure 26. DAC Register Contents
20
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
10.1.1 Bipolar Operation
The DAC101C081 is designed for single supply operation and thus has a unipolar output. However, a bipolar
output may be obtained with the circuit in Figure 27. This circuit will provide an output voltage range of ±5 Volts.
A rail-to-rail amplifier should be used if the amplifier supplies are limited to ±5 V.
10 pF
R2
+5V
R1
+5V
10 PF
+
-
0.1 PF
±5V
+
DAC101C081
SDA
-5V
VOUT
SCL
Figure 27. Bipolar Operation
The output voltage of this circuit for any code is found to be:
VO = (VA × (D / 1024) × ((R1 + R2) / R1) – VA × R2 / R1)
where D is the input code in decimal form.
(2)
With VA = 5 V and R1 = R2,
VO = (10 × D / 1024) – 5 V
(3)
A list of rail-to-rail amplifiers suitable for this application are indicated in Table 2.
Table 2. Some Rail-to-Rail Amplifiers
AMP
PKGS
LMP7701
SOT-23-5
37 uV
0.79 mA
LMV841
SC70-5
50 uV
1 mA
LMC7111
SOT-23-5
0.9 mV
25 µA
LM7301
SO-8
SOT-23-5
0.03 mV
620 µA
LM8261
SOT-23-5
0.7 mV
1 mA
Copyright © 2012–2016, Texas Instruments Incorporated
Typ VOS
Typ ISUPPLY
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
21
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
10.1.2 DSP/Microprocessor Interfacing
Interfacing the DAC101C081 to microprocessors and DSPs is quite simple. The following guidelines are offered
to simplify the design process.
10.1.2.1 Interfacing to the 2-wire Bus
Figure 28 shows a microcontroller interfacing to the DAC101C081 via the 2-wire bus. Pullup resistors (Rp)
should be chosen to create an appropriate bus rise time and to limit the current that will be sunk by the opendrain outputs of the devices on the bus. Please refer to the I2C™ Specification for further details. Typical pullup
values to use in Standard-Fast mode bus applications are 2kΩ to 10kΩ. SCL and SDA series resisters (RS) near
the DAC101C081 are optional. If high-voltage spikes are expected on the 2-wire bus, series resistors should be
used to filter the voltage on SDA and SCL. The value of the series resistance must be picked to ensure the VIL
threshold can be achieved. If used, RS is typically 51Ω.
DAC101C081/5
10 PF
VREF
4.7 PF
VA
0.1 PF
Regulated Supply
RP RP
VDD
PController
R S*
SDA
SDA
SCL
SCL
R S*
ADC101C021
SDA
SCL
I2C Device
SDA
SCL
*NOTE: RS is optional.
Figure 28. Serial Interface Connection Diagram
10.1.2.2 Interfacing to a Hs-mode Bus
Interfacing to a Hs-mode bus is very similar to interfacing to a standard-fast mode bus. In Hs-mode, the specified
rise time of SCL is shortened. To create a faster rise time, the master device (microcontroller) can drive the SCL
bus high and low. In other words, the microcontroller can drive the line high rather than leaving it to the pullup
resistor. It is also possible to decrease the value of the pullup resistors or increase the pullup current to meet the
tighter timing specs. Please refer to the I2C Specification for further details.
22
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
10.2 Typical Application
2
VA
4 SDA
1
5 SCL
VOUT DAC101C081CIMK
+5
120 pF
+5
3
+
6 ADR0
3
1 uF
5
1
A2
4
LM4132-3.3
4
5
3
2 .1 uF
-
.2 uF
2
180
+5
+3.3
10
VA
9
VIO
100 K
2
470 pF
+IN
1
VREF
ADC161S626
AV = 100
2.02 K
3
-IN
8
SCLK
7
DOUT
6
/CS
4,5
.2 uF
+5
3
100 K
5
-
1
A1
Pressure
Sensor
0.2 mV/Volt/PSI
4
+
180
470 pF
2
A1 and A2 = LMP7701
Figure 29. Pressure Sensor Gain Adjust
10.2.1 Design Requirements
A positive supply only data acquisition system capable of digitizing a pressure sensor output. In addition to
digitizing the pressure sensor output, the system designer can use the DAC101C081 to correct for gain errors in
the pressure sensor output by adjusting the bias voltage to the bridge pressure sensor.
10.2.2 Detailed Design Procedure
As shown in Equation 4, the output of the pressure sensor is relative to the imbalance of the resistive bridge
times the output of the DAC101C081, thus providing the desired gain correction.
Pressure Sensor Output = (DAC_Output × [(R2 / (R1 + R2) – (R4 / (R3 + R4)]
(4)
Likewise for the ADC161S626, Equation 5 shows that the ADC output is function of the Pressure Sensor Output
times relative to the ratio of the ADC input divided by the DAC101C081 output voltage.
ADC161S626 Output = (Pressure Sensor Output × 100 /(2 × VREF) ) × 216
Copyright © 2012–2016, Texas Instruments Incorporated
(5)
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
23
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Typical Application (continued)
10.2.3 Application Curve
Figure 30. INL vs Input Code
24
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
11 Power Supply Recommendations
11.1
Using References as Power Supplies
While the simplicity of the DAC101C081 implies ease of use, it is important to recognize that the path from the
reference input (VA for the DAC101C081 and VREF for the DAC101C085) to VOUT will have essentially zero
Power Supply Rejection Ratio (PSRR). Therefore, it is necessary to provide a noise-free supply voltage to the
reference. In order to use the full dynamic range of the DAC101C085, the supply pin (VA) and VREF can be
connected together and share the same supply voltage. Since the DAC101C081 consumes very little power, a
reference source may be used as the supply voltage. To ensure accuracy, it is required that VA and VREF be well
bypassed. The advantages of using a reference source over a voltage regulator are accuracy and stability. Some
low noise regulators can also be used. Listed below are a few reference and power supply options for the
DAC101C081. When using the DAC101C081, it is important to treat the analog supply (VA) as the reference.
11.1.1
LM4132
The LM4132, with its 0.05% accuracy over temperature, is a good choice as a reference source for the
DAC101C081. The 4.096-V version is useful if a 0 to 4.095-V output range is desirable or acceptable. Bypassing
the LM4132 VIN pin with a 0.1-µF capacitor and the VOUT pin with a 2.2-µF capacitor will improve stability and
reduce output noise. The LM4132 comes in a space-saving 5-pin SOT-23.
Input
Voltage
LM4132-4.1
C1
0.1 PF
C2
2.2 PF
C3
0.1 PF
VA VREF
DAC101C081/5
VOUT = 0V to 4.092V
SDA
SCL
Figure 31. The LM4132 as a Power Supply
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
25
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Using References as Power Supplies (continued)
11.1.2 LM4050
Available with accuracy of 0.44%, the LM4050 shunt reference is also a good choice as a reference for the
DAC101C081. It is available in 4.096-V and 5-V versions and comes in a space-saving 3-pin SOT-23.
Input
Voltage
R
IDAC
VZ
IZ
0.1 PF
0.47 PF
LM4050-4.1
or
LM4050-5.0
VA VREF
DAC101C081/5
VOUT = 0V to 5V
SDA
SCL
Figure 32. The LM4050 as a Power Supply
The minimum resistor value in the circuit of Figure 32 must be chosen such that the maximum current through
the LM4050 does not exceed its 15-mA rating. The conditions for maximum current include the input voltage at
its maximum, the LM4050 voltage at its minimum, and the DAC101C081 drawing zero current. The maximum
resistor value must allow the LM4050 to draw more than its minimum current for regulation plus the maximum
DAC101C081 current in full operation. The conditions for minimum current include the input voltage at its
minimum, the LM4050 voltage at its maximum, the resistor value at its maximum due to tolerance, and the
DAC101C081 draws its maximum current. These conditions can be summarized as:
R(min) = ( VIN(max) − VZ(min) ) /IZ(max)
(6)
and
R(max) = ( VIN(min) − VZ(max) ) / ( (IDAC(max) + IZ(min) )
where
•
•
•
•
26
VZ(min) and VZ(max) are the nominal LM4050 output voltages ± the LM4050 output tolerance over
temperature
IZ(max) is the maximum allowable current through the LM4050
IZ(min) is the minimum current required by the LM4050 for proper regulation and
IDAC(max) is the maximum DAC101C081 supply current.
Submit Documentation Feedback
(7)
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
Using References as Power Supplies (continued)
11.1.3
LP3985
The LP3985 is a low noise, ultra low dropout voltage regulator with a 3% accuracy over temperature. It is a good
choice for applications that do not require a precision reference for the DAC101C081. It comes in 3.0-V, 3.3-V
and 5-V versions, among others, and sports a low 30-µV noise specification at low frequencies. Because low
frequency noise is relatively difficult to filter, this specification could be important for some applications. The
LP3985 comes in a space-saving 5-pin SOT-23 and 5-bump DSBGA packages.
Input
Voltage
LP3985
0.1 PF
1 PF
0.01 PF
0.1 PF
VA
VREF
DAC101C081/5
VOUT = 0V to 5V
SDA
SCL
Figure 33. Using the LP3985 Regulator
An input capacitance of 1.0 µF without any ESR requirement is required at the LP3985 input, while a 1.0-µF
ceramic capacitor with an ESR requirement of 5 mΩ to 500 mΩ is required at the output. Careful interpretation
and understanding of the capacitor specification is required to ensure correct device operation.
11.1.4 LP2980
The LP2980 is an ultra low dropout regulator with a 0.5% or 1.0% accuracy over temperature, depending upon
grade. It is available in 3.0-V, 3.3-V and 5-V versions, among others.
Input
Voltage
VIN
VOUT
LP2980
ON /OFF
1 PF
0.1 PF
VA VREF
DAC101C081/5
VOUT = 0V to 5V
SDA
SCL
Figure 34. Using the LP2980 Regulator
Like any low dropout regulator, the LP2980 requires an output capacitor for loop stability. This output capacitor
must be at least 1.0µF over temperature, but values of 2.2µF or more will provide even better performance. The
ESR of this capacitor should be within the range specified in the LP2980 data sheet. Surface-mount solid
tantalum capacitors offer a good combination of small size and ESR. Ceramic capacitors are attractive due to
their small size but generally have ESR values that are too low for use with the LP2980. Aluminum electrolytic
capacitors are typically not a good choice due to their large size and have ESR values that may be too high at
low temperatures.
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
27
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
12 Layout
12.1
Layout Guidelines
For best accuracy and minimum noise, the printed circuit board containing the DAC101C081 requires separate
analog and digital areas. The areas are defined by the locations of the analog and digital power planes. Both of
these planes should be located on the same board layer. There should be a single ground plane. A single ground
plane is preferred if digital return current does not flow through the analog ground area. Frequently a single
ground plane design will use a fencing technique to prevent the mixing of analog and digital ground current.
Separate ground planes should only be utilized when the fencing technique is inadequate. The separate ground
planes must be connected in one place, preferably near the DAC101C081. Special care is required to ensure
that digital signals with fast edge rates do not pass over split ground planes. They must always have a
continuous return path below their traces.
The DAC101C081 power supply should be bypassed with a 4.7-µF and a 0.1-µF capacitor as close as possible
to the device with the 0.1 µF right at the device supply pin. The 4.7-µF capacitor should be a tantalum type and
the 0.1-µF capacitor should be a low ESL, low ESR type. The power supply for the DAC101C081 should only be
used for analog circuits.
Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the
board. These clock and data lines require controlled impedances.
12.2 Layout Example
VOUT
ADR0
SOT
VA
SCL
C1
SDA
GND
Figure 35. Layout Example
28
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
DAC101C081, DAC101C081Q, DAC101C085
www.ti.com
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
13 Device and Documentation Support
13.1 Device Support
13.1.1 Device Nomenclature
13.1.1.1 Specification Definitions
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB, which is VREF / 1024 = VA / 1024.
DIGITAL FEEDTHROUGH is a measure of the energy injected into the analog output of the DAC from the digital
inputs when the DAC output is not updated. It is measured with a full-scale code change on the data bus.
FULL-SCALE ERROR is the difference between the actual output voltage with a full scale code (FFFh) loaded
into the DAC and the value of VA x 1023 / 1024.
GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Zero and
Full-Scale Errors as:
GE = FSE - ZE
where
•
•
•
GE is Gain error
FSE is Full-Scale Error
and ZE is Zero Error.
(8)
GLITCH IMPULSE is the energy injected into the analog output when the input code to the DAC register
changes. It is specified as the area of the glitch in nanovolt-seconds.
INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a straight line
through the input to output transfer function. The deviation of any given code from this straight line is measured
from the center of that code value. The end point method is used. INL for this product is specified over a limited
range, per the Electrical Characteristics Table.
LEAST SIGNIFICANT BIT (LSB) is the bit that has the smallest value or weight of all bits in a word. This value is
LSB = VREF / 2n
where
•
VREF is the supply voltage for this product, and "n" is the DAC resolution in bits, which is 10 for the
DAC101C081.
(9)
MAXIMUM LOAD CAPACITANCE is the maximum capacitance that can be driven by the DAC with output
stability maintained.
MONOTONICITY is the condition of being monotonic, where the DAC has an output that never decreases when
the input code increases.
MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is
1/2 of VA.
MULTIPLYING BANDWIDTH is the frequency at which the output amplitude falls 3dB below the input sine wave
on VREFIN with a full-scale code loaded into the DAC.
POWER EFFICIENCY is the ratio of the output current to the total supply current. The output current comes from
the power supply. The difference between the supply and output currents is the power consumed by the device
without a load.
SETTLING TIME is the time for the output to settle to within 1/2 LSB of the final value after the input code is
updated.
TOTAL HARMONIC DISTORTION (THD) is the measure of the harmonics present at the output of the DACs
with an ideal sine wave applied to VREFIN. THD is measured in dB.
WAKE-UP TIME is the time for the output to exit power-down mode. This time is measured from the rising edge
of SCL during the ACK bit of the lower data byte to the time the output voltage deviates from the power-down
voltage of 0 V.
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
29
DAC101C081, DAC101C081Q, DAC101C085
SNVS801B – APRIL 2012 – REVISED JANUARY 2016
www.ti.com
Device Support (continued)
ZERO CODE ERROR is the output error, or voltage, present at the DAC output after a code of 000h has been
entered.
13.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
DAC101C081
Click here
Click here
Click here
Click here
Click here
DAC101C081Q
Click here
Click here
Click here
Click here
Click here
DAC101C085
Click here
Click here
Click here
Click here
Click here
13.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.4 Trademarks
E2E is a trademark of Texas Instruments.
I2C is a trademark of NXP Semiconductors.
All other trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: DAC101C081 DAC101C081Q DAC101C085
PACKAGE OPTION ADDENDUM
www.ti.com
2-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DAC101C081CIMK/NOPB
ACTIVE
SOT
DDC
6
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
X85C
DAC101C081CIMKX/NOPB
ACTIVE
SOT
DDC
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
X85C
DAC101C081CISD/NOPB
ACTIVE
WSON
NGF
6
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
X88
DAC101C081CISDX/NOPB
ACTIVE
WSON
NGF
6
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
X88
DAC101C081QISD/NOPB
ACTIVE
WSON
NGF
6
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
Q88
DAC101C081QISDX/NOPB
ACTIVE
WSON
NGF
6
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
Q88
DAC101C085CIMM/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
DAC101C085CIMMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
X91C
-40 to 125
X91C
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
2-Oct-2015
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Oct-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DAC101C081CIMK/NOPB
DAC101C081CIMKX/NOP
B
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SOT
DDC
6
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT
DDC
6
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
DAC101C081CISD/NOPB WSON
NGF
6
1000
178.0
12.4
2.8
2.5
1.0
8.0
12.0
Q1
WSON
NGF
6
4500
330.0
12.4
2.8
2.5
1.0
8.0
12.0
Q1
DAC101C081QISD/NOPB WSON
DAC101C081CISDX/NOP
B
NGF
6
1000
178.0
12.4
2.8
2.5
1.0
8.0
12.0
Q1
DAC101C081QISDX/NOP
B
WSON
NGF
6
4500
330.0
12.4
2.8
2.5
1.0
8.0
12.0
Q1
DAC101C085CIMM/NOP
B
VSSOP
DGK
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
DAC101C085CIMMX/NO
PB
VSSOP
DGK
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Oct-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC101C081CIMK/NOPB
SOT
DDC
6
1000
210.0
185.0
35.0
SOT
DDC
6
3000
210.0
185.0
35.0
WSON
NGF
6
1000
210.0
185.0
35.0
WSON
NGF
6
4500
367.0
367.0
35.0
DAC101C081CIMKX/NOP
B
DAC101C081CISD/NOPB
DAC101C081CISDX/NOP
B
WSON
NGF
6
1000
210.0
185.0
35.0
DAC101C081QISDX/NOP
B
DAC101C081QISD/NOPB
WSON
NGF
6
4500
367.0
367.0
35.0
DAC101C085CIMM/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
VSSOP
DGK
8
3500
367.0
367.0
35.0
DAC101C085CIMMX/NOP
B
Pack Materials-Page 2
MECHANICAL DATA
NGF0006A
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated