Advanced Information S m a r t M e s h® W i r e l e s s H A R T T M LTP5901/LTP5902-WHM 2.4 GHz 802.15.4 Eterna T M Mote Module About SmartMesh WirelessHART SmartMesh WirelessHART products are designed for the harshest industrial environments, where low power, reliability, resilience and scalability are key. SmartMesh WirelessHART solutions are well-suited for applications requiring WirelessHART standards compliance, as well as a wide range of applications from renewable energy generation, such as solar and wind power, to factory machine health monitoring and data center HVAC energy management. Smartmesh WirelessHART complies with the WirelessHART (IEC 62591) standard, offers the lowest power consumption in its class and is the most widely used WirelessHART product available. SmartMesh WirelessHART systems are easy for industrial automation vendors to integrate and simple for end users to deploy. Product Descriptions – LTP5901/LTP5902-WHM The LTP5901/LTP5902-WHM mote module combines Dust Networks’ robust sensor networking solution with Dust’s breakthrough EternaTM SoC technology in an easy-to-integrate 22-pin module, and may serve as a drop-in replacement for Dust Networks’ M2510 mote module. As part of the SmartMesh WirelessHART system, the LTP5901/LTP5902-WHM enables customers to integrate a standards-based wireless network into sensors and actuators to provide scalable bidirectional communications. The LTP5901/LTP5902-WHM is designed for use in line-powered, battery-powered, or energy-scavenging sensor and actuator applications that demand reliable performance and ultra-low power operation. With Dust Networks’ innovative IEEE 802.15.4-compliant design and integrated power amplifier, the LTP5901/LTP5902-WHM enables a decade of battery life on two AA batteries, including routing motes. All motes function as wireless routers, enabling a redundant, high performance, full-mesh topology. The LTP5901/LTP5902-WHM Mote modules combine Dust Networks’ robust sensor networking solution with Dust’s breakthrough EternaTM SoC Technology in an easy-to-integrate surface-mount printed circuit board (PCB). The LTP5901-WHM module includes an onboard chip antenna, while the LTP5902-WHM module includes an MMCX antenna connector. Both PCB modules will come with modular certifications for FCC, CE, and IC. To accelerate customer development time and reduce development costs, Dust Networks provides a fully engineered RF solution, comprehensive APIs, and complete development documentation. Key Product Features Highly Scalable • • • Ultra-low Power Operation Automatic network formation—new motes join automatically from anywhere in the network All motes are wireless routers, providing a full-mesh network that easily scales to tens of thousands of motes per square kilometer Time-synchronized communication across 15 channels virtually eliminates in-network collisions, allowing for dense deployments in overlapping radio space • Intelligent Networking Platform enables greater than 99.99% network reliability even in the most challenging monitoring and control environments Time-synchronized channel hopping seamlessly compensates for in band blocking and multipath fading in dynamic RF environments Industry-leading radio technology capable of line-powered, battery-powered, or energy-scavenging operation Automatic power optimization of every device in network, enabling a decade of network operation on two Lithium AA batteries Easy to Integrate and Deploy • Fully engineered RF, with power amplifier (PA), balun, and antenna matching circuitry A comprehensive application programming interface (API) provides a rich and flexible functionality to ease software development and device integration Secure Global Market Solution • • • WirelessHART (IEC62591) compliance Operates on 2.4 GHz global license-free band, providing customers with a single product for world-wide use RF Modular certifications (pending)-FCC, IC, and CE AES-128 bit encryption IEEE 802.15.4 PHY IEEE 802.15.4E MAC RSSI Interoperable with WirelessHART devices Encryption and Authentication • • • Superior Reliability • • Linear Technology / Dust Networks Advanced Information Table of Contents General ..............................................................................................................4 1.0 1.1 Related Documentation ..................................................................................... 4 1.2 Conventions..................................................................................................... 4 1.2.1 Signal Naming .............................................................................................. 4 1.2.2 Number Format ............................................................................................ 4 2.0 Introduction .......................................................................................................5 2.1 Power Supply ................................................................................................... 5 2.1.1 Supply Monitoring and Reset .......................................................................... 6 2.2 Precision Timing ............................................................................................... 6 2.2.1 Time Synchronization .................................................................................... 6 2.3 Time References............................................................................................... 6 2.3.1 Relaxation Oscillator...................................................................................... 6 2.3.2 32.768 kHz Crystal ....................................................................................... 6 2.3.3 20 MHz Crystal ............................................................................................. 6 2.4 Radio .............................................................................................................. 6 2.5 UARTs............................................................................................................. 7 2.5.2 API UART Protocol......................................................................................... 7 2.5.3 CLI UART..................................................................................................... 8 2.6 Autonomous MAC ............................................................................................. 8 2.7 Security .......................................................................................................... 8 2.8 Temperature Sensor ......................................................................................... 8 2.8.1 Radio Inhibit ................................................................................................ 8 2.8.2 Sleep .......................................................................................................... 9 2.10 Flash Programming ........................................................................................... 9 3.0 9 4.0 Operation ...........................................................................................................9 4.1 Start Up .......................................................................................................... 9 4.1.1 Fuse Table ..................................................................................................10 4.2 Serial Flash Emulation ......................................................................................10 4.3 Operation .......................................................................................................10 4.3.1 Active State ................................................................................................10 4.3.2 Doze State..................................................................................................10 4.4 5.0 Duty Cycling and Autonomous Peripherals...........................................................11 Pinout ..............................................................................................................12 5.2 Eterna Mote Modules........................................................................................12 5.3 Power Supply ..................................................................................................15 5.3.1 Antenna .....................................................................................................15 2 5.4 Analog ...........................................................................................................15 5.5 JTAG..............................................................................................................15 Linear Technology / Dust Networks Eterna Datasheet Advanced Information 6.0 Absolute Maximum Ratings ..............................................................................16 7.0 Recommended Operating Conditions................................................................17 8.0 Electrical Characteristics ..................................................................................17 8.1 Radio Specifications .........................................................................................17 8.2 DC Characteristics ...........................................................................................17 8.3 Radio Receive Characteristics ............................................................................18 8.4 Radio Transmitter Characteristics.......................................................................19 8.5 Digital I/O Characteristics .................................................................................19 8.6 Temperature Sensor Characteristics ...................................................................20 8.7 ADC Characteristics .........................................................................................20 8.8 System Characteristics .....................................................................................20 8.9 UART AC Characteristics ...................................................................................21 8.10 TIMEn AC Characteristics ..................................................................................22 8.11 SLEEPn AC Characteristics ................................................................................22 8.12 RADIO_INHIBIT AC Characteristics.....................................................................22 8.13 FLASH AC Characteristics..................................................................................23 8.14 Flash Programming AC Characteristics ................................................................23 9.0 Typical Performance Characteristics ................................................................24 10.0 Mechanical Details ...........................................................................................25 10.2 Mote Module ...................................................................................................25 10.3 Soldering Information ......................................................................................27 11.0 Regulatory and Standards Compliance .............................................................27 11.1 Compliance to Restriction of Hazardous Substances (RoHS) ...................................27 12.0 References .......................................................................................................27 13.0 Order Information............................................................................................27 Eterna Datasheet Linear Technology / Dust Networks 3 Advanced Information 1.0 1.1 General Related Documentation • 040-0102 Eterna Integration Guide • 040-0109 Design Specific Configuration Guide • 040-0110 Eterna Serial Programmer Guide 1.2 Conventions 1.2.1 Signal Naming The naming convention for Eterna signals is UPPER_CASE_SEPARATED_BY_UNDERSCORE. Active-low signals, such as RESETn, add a trailing lower case n. An exception to the naming convention is UART transmit and receive signals which are named consistent with industry practice as RX and TX, omitting the lower case n, despite being active low signals. The terms assertion and active refers to a signal in a logically true state: logic ‘1’ for active high signals and logic ‘0’ for active low signals. The terms negated and inactive refer to a signal being in its logically false state: logic ‘0’ for active high signals and logic ‘1’ for active low signals. 1.2.2 Number Format The 0x prefix indicates a hexadecimal number follows. The 0b prefix indicates a binary number follows. The lack of a prefix indicates a decimal number follows. 4 Linear Technology / Dust Networks Eterna Datasheet Advanced Information Introduction 2.0 Eterna is the world’s most energy-efficient IEEE 802.15.4 compliant platform enabling battery and energy harvested endpoint, routing and network management solutions. With a powerful 32-bit ARM® Cortex™-M3, best in class radio, flash, RAM and purpose-built peripherals, Eterna provides a flexible, scalable and robust networking solution for applications demanding both minimal energy consumption and data reliability in even the most challenging RF environments. Shown in Figure 1, Eterna integrates purpose-built peripherals that excel in both low operating-energy consumption and the ability to rapidly and precisely cycle between operating and low-power states. Items in the shaded region correspond to the analog/RF components. 32 kHz 32 kHz, 20 MHz Timers Sched. Voltage Reference Primary DC/DC Converter SRAM 72 KB Core Regulator Clock Regulator Flash 512 KB Relaxation Oscillator Flash Controller Analog Regulator PA DC/DC Converter PoR AES 802.15.4 Mod DAC 20 MHz PMU / Clock Control LPF PA Code Auto MAC Cortex-M3 802.15.4 Framing DMA PLL System 802.15.4 Demod ADC Limiter BPF AGC IPCS SPI Slave CLI UART (2 pin) API UART (6-pin) ADC Ctrl. 10-bit ADC VGA PPF LNA RSSI S PTAT Bat. Load 4-bit DAC Figure 1 Eterna Block Diagram 2.1 Power Supply Eterna is powered from a single pin, VSUPPLY, which powers the I/O cells and is also used to generate internal supplies. Eterna’s two on-chip DC/DC converters minimize Eterna’s energy consumption while the device is awake. To prevent power from being wasted the DC/DC converter is disabled when the device is in low-power state. Eterna’s rejection of supply noise is substantial owing to the two integrated DC/DC converters and three integrated low-dropout regulators. Eterna’s operating supply range is high enough to support direct connection to Li-SClO2 sources and wide enough to support battery operation over a broad temperature range. Eterna Datasheet Linear Technology / Dust Networks 5 Advanced Information 2.1.1 Supply Monitoring and Reset Eterna integrates an Power on Reset (PoR) circuit and as the RESETn input pin is nominally configured with an internal pullup resistor, thus no connection is required. For a graceful shutdown, the software and networking layers be cleanly halted prior to assertion of the RESETn pin. Eterna includes a soft brown-out monitor that fully protects the Flash from corruption in the event that power is removed while writing to flash. Integrated flash supervisory functionality in conjunction with *** (do we do a JFS?) yields a robust non-volatile file system. 2.2 Precision Timing Eterna, differs from competing 802.15.4 product offerings by providing low-power dedicated timing hardware and timing algorithms that provide timing precision two to three orders of magnitude better than any other available low-power solution. Improved timing accuracy allows motes to minimize the amount of radio listening time required to ensure packet reception thereby lowering even further the power consumed by an Eterna network. Eterna’s patented timing hardware and timing algorithms provide superior performance over rapid temperature changes, further differentiating Eterna’s reliability when compared with other wireless products. In addition, precise timing enables networks to reduce spectral dead time, increasing total network throughput. 2.2.1 Time Synchronization In addition to coordinating timeslots across the network, which is transparent to the user, Eterna’s unparalleled timing management is used to support two mechanisms to share network time. Having an accurate, shared, network-wide time base enables events to be accurately time stamped or tasks to be performed in a synchronized fashion across a network. Eterna will send a time packet through its serial interface when one of the following occurs: • Eterna receives an HDLC request to read time • The TIMEn signal is asserted The use of TIMEn has the advantage of being more accurate. The value of the timestamp is captured in hardware relative to the rising edge of TIMEn. If the HDLC request is used, due to packet processing the value of the timestamp may be captured several milliseconds after receipt of the packet. See Section 8.10 for the time functions definition and specifications. 2.3 Time References Eterna includes three clock sources: a low power oscillator designed for a 32.768 kHz crystal, the radio reference oscillator designed for a 20 MHz crystal, and an internal relaxation oscillator. 2.3.1 Relaxation Oscillator The relaxation oscillator is the primary clock source for Eterna, providing the clock for the CPU, memory subsystems, and all peripherals. The internal relaxation oscillator typically starts up in a few μs, providing an expedient, low-energy method for duty cycling between active and low power states. Quick start-up from the doze state, defined in section 4.0, allows Eterna to wake up and receive data over the UART and SPI interfaces by simply by detecting activity the appropriate signals. 2.3.2 32.768 kHz Crystal Once Eterna is powered up and the 32.768 kHz crystal source has begun oscillating, the 32.768 kHz crystal remains operational while in the Active state, and is used as the timing basis when in Doze state. See Section 4.0 for a description of Eterna’s operational states. 2.3.3 20 MHz Crystal The 20 MHz crystal source provides a frequency reference for the radio, and is automatically enabled and disabled by Eterna as needed. 2.4 Radio Eterna is the lowest-power commercially available 2.4 GHz IEEE 802.15.4e radio by a substantial margin. (Please refer to section 8.2 for power consumption numbers.). Eterna’s integrated power amplifier is calibrated and temperature-compensated to consistently provide power at a limit suitable for worldwide radio certifications. Additionally, Eterna uniquely includes a 6 Linear Technology / Dust Networks Eterna Datasheet Advanced Information hardware-based autonomous MAC that handles precise sequencing of peripherals, including the transmitter, the receiver, and AES peripherals. The hardware-based autonomous MAC minimizes CPU activity, thereby further decreasing power consumption. 2.5 UARTs The principal network interface is through the application programming interface (API) UART. A command-line interface (CLI) is also provided for support of test and debug functions. Both UARTs sense activity continuously, consuming virtually no power until data is transferred over the port and then automatically returning to their lowest power state after the conclusion of a transfer. 2.5.2 API UART Protocol Eterna’s API UART operates in Mode 4, incorporating optional flow control, at 115200 baud. Packets are HDLC encoded with one stop bit and no parity bits. The flow control signals for Eterna’s API receive path are shown in Figure 5. If the flow control signals are used (recommended) transfers are initiated from a companion processor by asserting UART_RX_RTSn. Eterna responds by asserting UART_RX_CTSn. If flow control is used, after detecting the assertion of UART_RX_CTSn the companion processor may send the entire packet. Following the transmission of the final byte in the packet the companion processor negates UART_RX_RTSn and waits until the negation of UART_RX_CTSn before asserting UART_RX_RTSn again. Flow control automatically ensures compliance with inter-packet delay requirements, so explicit delay-checking is not required. If flow control is not desired or needed it may be disabled by tying UART_RX_RTSn high. When flow control is not used the companion processor may send the entire packet; in this case the companion processor must comply with the minimum inter-packet delay as defined in section 8.9. Figure 5 UART Mode 4 Receive Flow Control UART Mode 4 also incorporates level-sensitive flow control for Eterna UART transmissions on the UART TX pin. Packets are HDLC encoded with one stop bit and no parity bits. The flow control signals for TX are shown in Figure 6. A transfer request is signaled by Eterna device asserting UART_TX_RTSn. The UART_TX_CTSn signal may be actively driven by the companion processor when it is ready to receive a packet or it may be tied low if the companion processor will always be ready to receive a packet. After detecting a logic ‘0’ on UART_TX_CTSn Eterna sends the entire packet. Following the transmission of the final byte in the packet Eterna negates UART_TX_RTSn and waits for a minimum period (what is the period called?) defined in section 8.9 before asserting UART_TX_RTSn again (if a packet needs to be transmitted) Eterna Datasheet Linear Technology / Dust Networks 7 Advanced Information Figure 6 UART Mode 4 Transmit Flow Control For details on the timing of the UART protocol, see section 8.9 (UART AC Characteristics). 2.5.3 CLI UART The Command Line Interface (CLI) UART port is a two wire protocol (TX and RX) that operates at a fixed 9600 baud rate with one-stop bit and no parity. The CLI UART interface is intended to support command-line instructions and response activity. 2.6 Autonomous MAC Eterna was designed as a system solution with the objective of providing a reliable, ultra-low power, and secure network. A reliable network capable of dynamically optimizing operation over changing environments requires solutions that are far too complex to completely support through hardware acceleration alone. As described in Section 2.2, proper time management is essential for optimizing a solution that is both low power and reliable. To address this solution Eterna includes the Autonomous MAC, which includes hardware support for controlling all of the time-critical radio operations. The Autonomous MAC provides two benefits: first, preventing variable software latency from affecting network timing and second, greatly reducing system power consumption by allowing the CPU to remain inactive during the majority of the radio activity. The Autonomous MAC, unique to Eterna, provides software-independent timing control of the radio and radiorelated functions, resulting in superior reliability and exceptionally low power. 2.7 Security Network security is an often overlooked component of a complete network solution. Proper implementation of security protocols is significant in terms of both engineering effort and market value in an OEM product. Eterna system solutions provide a FIPS-197 validated encryption scheme, and goes further, providing a complete set of mechanisms to protect network security. Eterna includes hardware support for electronically locking devices, thereby preventing access to Eterna’s flash and RAM memory. This lock-out feature provides a means to securely unlock a device should support of a product require access. For details see 040-0109 Design Specific Configuration Guide. 2.8 Temperature Sensor Eterna includes a calibrated temperature sensor on chip. The temperature readings are available locally through Eterna’s serial API, in addition to being available via the network manager. The performance characteristics of the temperature sensor can be found in Section 8.6. 2.8.1 Radio Inhibit The RADIO_INHIBIT digital interrupt enables an external controller to temporarily disable the radio software drivers (for example, to take a sensor reading that is susceptible to radio interference). When RADIO_INHIBIT is asserted the software radio drivers will disallow radio operations including clear channel assessment, packet transmits, or packet receipts. If a radio event is in progress radio inhibit will take effect after the present operation completes. For details on the timing associated with RADIO_INHIBIT, see Section 8.12. 8 Linear Technology / Dust Networks Eterna Datasheet Advanced Information 2.8.2 Sleep The SLEEPn digital interrupt enables an external controller to temporarily disable Eterna’s duty cycling between active and Doze states (see Section 4.0 for state definitions). Forcing Eterna to the Doze state should only be done when absolutely necessary, such as when taking a very sensitive sensor reading, as forcing a device into a Doze state will on the average increase the energy consumption of other devices in the network. When SLEEPn is asserted the software will go into a Doze state until the SLEEPn signal is negated. For details on the timing associated with SLEEPn, see Section 8.11. 2.10 Flash Programming Eterna’s software images are loaded via the IPCS, in-circuit programming control system, SPI interface. Sequencing of RESETn and FLASH_P_ENn, as described in Section 4.0, places Eterna in a state emulating a serial flash to support incircuit programming. Hardware and software for supporting development and production programming of devices is described in 040-0110 Eterna Serial Programmer Guide. The serial protocol, SPI, and timing parameters are described in Section 8.13. 4.0 Operation In order to provide capabilities and flexibility in addition to ultra low power, Eterna operates in various states, as shown in Figure 8 and described in this section. Power-On Reset VSUPPLY > PoR RESETn low and FLASH_P_ENn low Load Fuse Settings RESETn low and FLASH_P_ENn high Serial Flash Emulation Set RESETn high and FLASH_P_EN high for 125 µs, then set RESETn low Reset De-assert RESETn Boot Start Up Assert RESETn Assert RESETn Assert RESETn CPU and peripherals inactive Doze Deep Sleep Active HW or PMU Event lowPowerSleep Command Operation Figure 8 Inactive State Diagram – Operating Modes 4.1 Start Up Start Up occurs as a result of either tripping of the power-on-reset circuit or the assertion of RESETn. After the completion of power-on-reset (see Section 2.1.1) or the falling edge of an internally synchronized RESETn, Eterna loads its Fuse Table (see section 4.1.1), including setting I/O direction. In this state, Eterna checks the state of the FLASH_P_ENn and RESETn Eterna Datasheet Linear Technology / Dust Networks 9 Advanced Information and enters the serial flash emulation mode, if both signals are asserted. If the FLASH_P_ENn pin is not asserted but RESETn is not asserted, Eterna automatically reduces its energy consumption to a minimum until RESETn is released. Once RESETn is deasserted, Eterna goes through a boot sequence, and then enters the Active state. 4.1.1 Fuse Table Eterna’s Fuse Table is a 2 KB page in flash that contains two data structures, one for hardware configuration immediately following Power on Reset or the assertion of RESETn and one for configuration of design specific parameters. Hardware support for configuration includes configuration of I/O, preventing I/O leakage from negatively affecting current consumption during power on, which can be a significant issue for current limited supplies. Examples of design-specific parameters include setting of UART modes, clock sources and trim values. Fuse Tables are created via the Fuse Table application software described in 040-0109 Design Specific Configuration Guide. Fuse Tables are loaded into flash using the same software and in-circuit programmer used to load Eterna’s networking software image – see the 040-0110 Eterna Serial Programmer Guide for details. 4.2 Serial Flash Emulation When both RESETn and FLASH_P_ENn are asserted, Eterna disables normal operation and enters a mode to emulate the operation of a serial flash. In this mode, its flash can be programmed with software updates. For details, see Section 2.10. 4.3 Operation Once Eterna has completed startup, Eterna transitions to the Operational group of states (active / CPU active, active / CPU inactive, and Doze). There, Eterna cycles between the various states, automatically selecting the lowest power state possible while fulfilling the demands of network operation. 4.3.1 Active State In Active state, the Eterna’s relaxation oscillator is running and peripherals are enabled as needed. The ARM Cortex-M3 cycles as needed between CPU-active and CPU-inactive (referred to in the ARM Cortex-M3 literature as “Sleep Now” or “Sleep on Exit” modes). Eterna’s extensive use of DMA and intelligent peripherals that can independently move Eterna between the Active and Doze states minimizes the time the CPU is active, significantly reducing Eterna’s energy consumption. 4.3.2 Doze State The Doze state consumes orders of magnitude less current than the Active state (see Table 6) and is entered when all of the peripherals, save the low power portion of the timer module, and the CPU are inactive. In the Doze state Eterna’s full state is retained and Eterna is configured to detect, wake, and rapidly respond to activity on I/Os (such as UART signals and the TIMEn pin). The Doze state also uses the 32.768-kHz oscillator and 32 kHz based timers are active. 10 Linear Technology / Dust Networks Eterna Datasheet Advanced Information 4.4 Duty Cycling and Autonomous Peripherals Eterna’s ability to quickly and efficiently transition between Doze and Active states, in conjunction with the ability of peripherals to operate autonomously for most operations (shown in Figure 9), enables the system solution to significantly reduce power consumption. For example the system can automatically go from Doze to Active and determine if RF energy is present. The CPU is then only woken if a packet is detected, otherwise Eterna returns to Doze mode. Figure 9 Low Energy Duty Cycling Eterna Datasheet Linear Technology / Dust Networks 11 Advanced Information 5.0 5.2 Pinout Eterna Mote Modules The Eterna mote modules are shown in Figure 11 and Figure 12. Pins are described in Table 2, where they are grouped by function. In some cases, a pin may have multiple possible functions. Note: All unused input pins not configured with a pull resistor (see Pull column in pin out table) must be driven to an inactive state to avoid excess leakage and undesired operation. Leakage due to floating inputs can be substantially greater than Eterna’s average power consumption. Antenna Connector GND 1 66 GND RESERVED 2 65 NC NC 3 64 RADIO_INHIBIT LNA_EN 4 63 TIMEn RADIO_TX 5 62 UART_TX RADIO_TXn 6 61 UART_TX_CTSn AI_2 7 60 UART_TX_RTSn AI_1 8 59 UART_RX AI_3 9 58 UART_RX_CTSn AI_0 10 57 UART_RX_RTSn GND 11 56 GND RESERVED 12 55 VSUPPLY NC 13 54 RESERVED NC 14 53 NC RESETn 15 52 NC TDI 16 51 FLASH_P_ENn TDO 17 50 SPIS_SSn TMS 18 49 SPIS_SCK TCK 19 48 GPIO26 / SPIS_MOSI GND 20 47 SPIS_MISO DP4 21 46 PWM0 RESERVED 22 45 DP1 RESERVED 23 44 SPIM_SS_0n RESERVED 24 43 SPIM_SS_1n DP3 25 42 GND DP2 / GPIO21 26 41 SPIM_SCK SLEEPn 27 40 SPIM_MOSI DP0 28 39 IPCS_SSn / GPIO3 NC 29 38 SPIM_MISO GND 30 37 GND Figure 11 LTP5902-WHM – Mote Module with MMCX Antenna Connector 12 Linear Technology / Dust Networks Eterna Datasheet Advanced Information Figure 12 LTP5901-WHM – Mote Module with Chip Antenna Eterna Datasheet Linear Technology / Dust Networks 13 Advanced Information Table 2 Eterna Mote Module Pinout Assignments Mechanical NA No MECH Contacts for mechanical support of MMCX connector Power Supply Type I/O Pull Description 1 GND Power - - Ground 11 GND Power - - Ground 20 GND Power - - Ground 30 GND Power - - Ground 34 GND Power - - Ground 37 GND Power - - Ground 42 GND Power - - Ground 56 GND Power - - Ground 66 GND Power - - Ground 55 VSUPPLY Module power supply input Power - - Type I/O Pull LNA_EN 1 O - External LNA enable GPIO17 1 I/O - General purpose digital I/O RADIO_TX 1 O - Radio TX active (external PA enable/switch control) GPIO18 1 I/O - General purpose digital I/O No 4 5 6 64 Radio Description RADIO_TXn 1 O - Radio TX active (external PA enable/switch control), active low GPIO19 1 I/O - General purpose digital I/O RADIO_INHIBIT 1* I - Radio Inhibit I/O - General purpose digital I/O GPIO15 Type I/O Pull 10 No AI_0 Analog Analog I - Analog input 0 8 AI_1 Analog I - Analog input 1 9 AI_3 Analog I - Analog input 3 7 AI_2 Analog I - Analog input 2 Type I/O Pull 1 I UP Type I/O Pull UP No 15 General RESETn No JTAG 16 TDI 1 I 17 TDO 1 O - 18 TMS 1 I UP 19 TCK 1 I DOWN Type I/O Pull No CLI Description Description Reset, Input, active low Description JTAG test data in JTAG test data out JTAG test mode select JTAG test clock Description 31 UARTC0_TX 2 O - CLI UART 0 transmit 32 UARTC0_RX 1 I UP CLI UART 0 receive UART Type I/O Pull UART_RX_RTSn 1* I - No 57 Description UART receive (RTS) request to send, active low 58 UART_RX_CTSn 1 O - UART receive (CTS) clear to send, active low 59 UART_RX 1* I - UART receive 60 UART_TX_RTSn 1 O - UART transmit (RTS) request to send, active low 61 UART_TX_CTSn 1* I - UART transmit (CTS) clear to send, active low 62 UART_TX 2 O - UART transmit 14 Linear Technology / Dust Networks Eterna Datasheet Advanced Information No 33 IPCS SPI / FLASH Programming Type I/O Pull 2 O - SPI flash emulation (MISO) master in slave out port I/O - General purpose digital I/O I - SPI flash emulation (MOSI) master out slave in port I/O - General purpose digital I/O IPCS_MISO GPIO6 35 IPCS_MOSI 1 GPIO5 36 IPCS_SCK 1 I - SPI flash emulation (SCK) serial clock port I/O - General purpose digital I/O I - SPI flash emulation slave select, active low I/O - General purpose digital I/O I UP Type I/O Pull GPIO4 39 Description IPCS_SSn 1 GPIO3 Flash program enable, active low Note that this functionality is available only when RESETn is asserted 51 FLASH_P_ENn No Special Purpose Digital 27 SLEEPn 1* I - Deep Sleep, active low 63 TIMEn 1* I - Time capture request, active low Description * Input signals that must be driven or pulled to a valid state to avoid leakage. 5.3 Power Supply Eterna is powered from a single pin, VSUPPLY, and generates all required supplies internally. With two integrated DC/DC converters and four voltage regulators, the sensitivity to noise on VSUPPLY is minimal. However, during typical operation Eterna will vary its load on the power supply from the μA range to 10’s of mA over a few μs. During such transients, the power supply must meet the specifications for supply noise tolerance. Eterna is designed to operate with specific decoupling capacitance on VCORE, VDDA, VOSC, VDDPA, and VPRIME, as well as the internal converter capacitors C1 through C4. Failure to use correctly sized ceramic capacitors can result in supply instability and performance degradation. 5.3.1 Antenna Eterna allows direct connection to a single-ended 50-Ohm antenna; an internal TX/RX switch simplifies external circuitry requirements. Because both the transmit and the receive paths are single-ended, a balun (with its associated cost and efficiency loss) are not required. Eterna provides options to set typical output power to 0 dBm or to +8 dBm using the on-chip PA. For further details on radio transmit and receive, see section 2.4. 5.4 Analog Eterna has four analog inputs. Its 10-bit ADC includes a 4-bit DAC for adjusting offset and a 3-bit VGA, as shown in Figure 13. The software application layer controls ADC operation and may be configured to automatically sample any combination of the internal temperature sensor, or analog input signals. Figure 13 Analog to Digital Chain 5.5 JTAG Eterna includes an IEEE 1149.1-compliant JTAG port for boundary scan. Eterna Datasheet Linear Technology / Dust Networks 15 Advanced Information 6.0 Absolute Maximum Ratings The absolute maximum ratings shown in Table 3 should not be violated under any circumstances. Permanent damage to the device may be caused by exceeding one or more of these parameters. Unless otherwise noted, all voltages in Table 3 are relative to GND. Table 3 Absolute Maximum Ratings Parameter Min Supply voltage (VSUPPLY to GND) Voltage on any digital I/O pin Max Units –0.3 3.76 V –0.3 VSUPPLY + 0.3 up to 3.76 V +10 dBm –55 +105 °C Extended storage at high temperature is discouraged, as this negatively affects the data retention of Eterna’s calibration data. Lead temperature +245 °C For 10 seconds VSWR of antenna 3:1 Input RF level Storage temperature range Typ Comments Input power at antenna connector ESD protection Antenna pad ±8000 V HBM All other pads ±1000 V HBM ±100 V CDM Caution! ESD sensitive device. Precaution should be used when handling the device in order to prevent permanent damage. 16 Linear Technology / Dust Networks Eterna Datasheet Advanced Information Recommended Operating Conditions 7.0 Table 4 Recommended Operation Conditions Parameter Conditions Min Typ Max VSUPPLY range Including noise and load regulation 2.1 3.6 3.76 V Voltage supply noise Requires recommended RLC filter, 50 Hz to 2 MHz 250 mVp-p Operating temperature range Operating relative humidity Non-condensing –40 +85 °C 10 90 % RH Power on Reset threshold 1.5 Temperature ramp V -8 8.0 Electrical Characteristics 8.1 Radio Specifications Units +8 °C/min Max Units 2.4835 GHz The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 5 Detailed Radio Specifications Parameter Frequency Band Conditions As specified by [ 1 ] Min Typ 2.4000 Number of channels 15 Channel separation As specified by [ 1 ] Occupied channel bandwidth At –20 dBc Channel Center Frequency Where k = 11 to 25.‡ Modulation IEEE 802.15.4 DSSS Raw data rate As specified by [ 1 ] Range* † Indoor Outdoor† Free space 25 °C, 50% RH, +2 dBi omni-directional antenna 5 MHz 2.7 MHz 2405 + 5 * (k-11) MHz 250 kbps 100 300 1200 m m m * Actual RF range performance is subject to a number of installation-specific variables including, but not restricted to ambient temperature, relative humidity, presence of active interference sources, line-of-sight obstacles, and nearpresence of objects (for example, trees, walls, signage, and so on) that may induce multipath fading. As a result, actual performance varies. † 1 meter above ground. ‡ Channel 26 as specified by [ 1 ] is not used.. 8.2 DC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 6 DC Specifications Parameter Reset Conditions Units 0.8 µA RAM on; ARM Cortex-M3, flash, radio, and peripherals off, all data and state retained, 32.768 kHz reference active 1.2 µA 20 mA µA System operating at 14.7 MHz Radio Tx Flash Write at +8 dBm output power Eterna Datasheet Max 1.2 Serial Flash Emulation Peak Operating current Typ After power-on reset Deep Sleep Doze Min 30 Linear Technology / Dust Networks mA 17 Advanced Information Parameter Conditions Min Typ at 0 dBm output power Max Units 26 mA ARM Cortex-M3, RAM, and flash on; radio and peripherals off Active* CLK = 7.37 MHz, Vcore = 1.8 V 2.4 mA 3 mA 2.5 mA 0 dBm output power +8 dBm output power 5.4 9.7 mA mA Mesh Network - CLK = 7.3728 MHz, AES active 4.5 mA Flash write Single bank write Flash erase Single bank page or mass erase † Mesh Network - CLK = 7.3728 MHz, AES active Radio Tx Radio Rx† Note: See section 3.0 for detailed operational definitions of states. * CLK = Clock frequency of CPU and peripherals. † Current with autonomous MAC handling packet transmission and reception; CPU idle. 8.3 Radio Receive Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 7 Radio Receive Characteristics Parameter Conditions Min Typ Max Units Receiver sensitivity PER = 1%, as specified by [ 1 ] –93 Receiver sensitivity PER = 50% –95 dBm 0 dBm Saturation (maximum input level) dBm Adjacent channel rejection (high side) Desired signal at -82 dBm, adjacent modulated channel at 5 MHz, PER = 1%, as specified by [ 1 ] 22 dBc Adjacent channel rejection (low side) Desired signal at -82 dBm, adjacent modulated channel at -5 MHz, PER = 1%, as specified by [ 1 ] 19 dBc Alternate channel rejection (high side) Desired signal at -82 dBm, adjacent modulated channel at 10 MHz, PER = 1%, as specified by [ 1 ] 40 dBc Alternate channel rejection (low side) Desired signal at -82 dBm, adjacent modulated channel at -10 MHz, PER = 1%, as specified by [ 1 ] 36 dBc Second alternate channel rejection Desired signal at -82 dBm, adjacent modulated channel at +/-10 MHz, PER = 1%, as specified by [ 1 ] 42 dBc Co-channel rejection Desired signal at -82 dBm. Undesired signal is 802.15.4 modulated at same frequency. PER = 1%, as specified by [ 1 ] –6 dBc <–55 dBm ±50 ppm ±50 ppm –10 to –90 dBm RSSI accuracy ±6 dB RSSI resolution 1 dB LO feed through Frequency error tolerance [ 1 ] requires ±40 Symbol rate error tolerance RSSI input range 18 Linear Technology / Dust Networks Eterna Datasheet Advanced Information 8.4 Radio Transmitter Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 8 Radio Transmitter Characteristics Parameter Conditions Output power Calibrated settings Delivered to a 50 Ω load, over temperature and voltage ranges Spurious emissions Conducted measurement with a 50 Ω single-ended load, +8 dBm output power. All measurements made with Max Hold. RF implementation per Eterna reference design. 30 MHz to 1000 MHz 1 GHz to 12.75 GHz Upper Band Edge (Peak) Upper Band Edge (Average) Lower Band Edge Harmonic emissions 2nd Harmonic Min RBW = 120 kHz, VBW = 100 Hz RBW = 1 MHz, VBW = 3 MHz RBW = 1 MHz, VBW = 3 MHz RBW = 1 MHz, VBW = 10 Hz RBW = 100 kHz, VBW = 100 kHz Conducted measurement delivered to a 50 Ω load, Resolution Bandwidth = 1 MHz, Video Bandwidth = 1 MHz, RF implementation per Eterna reference design Max Units 0 +8 dBm dBm <–70 –45 -37 -49 -45 dBm dBm dBm dBm dBc dBm –50 rd –45 3 Harmonic 8.5 Typ Digital I/O Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 9 Digital I/O Type 1 Parameter Conditions Min Typ Max Units VIL (low-level input voltage) –0.3 0.6 V VIH (high-level input voltage) VSUPPLY - 0.3† VSUPPLY + 0.3† V 0.4 V VSUPPLY + 0.3† V VOL (low-level output voltage) IOL(max) = 1.2 mA VOH (high-level output voltage) IOH(max) = −1.8 mA Input leakage current pull-up / pull-down pins disabled. † VSUPPLY - 0.3† 50 nA Min and Min and Max IO input levels must respect the Minimum and Maximum voltages for VSUPPLY. Table 10 Digital I/O Type 2 Parameter Conditions Min Typ Max Units VIL (low-level input voltage) –0.3 0.6 V VIH (high-level input voltage) VSUPPLY - 0.3† VSUPPLY + 0.3† V 0.4 V VSUPPLY + 0.3† V 0.4 V VSUPPLY V VOL (low-level output voltage) Low Drive IOL(max) = 2.2 mA VOH (high-level output voltage) Low Drive IOH(max) = −3.2 mA VOL (low-level output voltage) High Drive IO(max) = 4.5 mA VOH (high-level output voltage) IOH(max) = −6.3 mA Eterna Datasheet VSUPPLY - 0.3† VSUPPLY Linear Technology / Dust Networks 19 Advanced Information - 0.3† High Drive Input leakage current † + 0.3† 50 nA Min and Min and Max IO input levels must respect the Minimum and Maximum voltages for VSUPPLY. 8.6 Temperature Sensor Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 11 Temperature Sensor Characteristics Parameter Conditions Min Typ Max Units Offset Temperature offset error at 25 ºC ±0.25 °C Slope error Slope error from -40 to +85 ºC ±0.033 °C/°C 8.7 ADC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 12 ADC Characteristics Parameter Conditions Min Variable gain amplifier Gain Gain error 1 Digital to analog converter (DAC) Offset output Differential non-linearity (DNL) Analog to digital converter (ADC) Full-scale, signal Resolution Offset Differential non-linearity (DNL) Integral non-linearity (INL) Settling time Conversion time Current consumption Typ 1.8/16 Max Units 8 1 % 1.8 7.2 V mV ±4 1 1 10 20 50 V mV LSB LSB LSB µs µs µA 35 2 pF kOhm 1.80 1.8 Midscale 10-kOhm source impedance Analog Inputs* Load Input resistance 17 1 * The analog inputs to the ADC can be model as a series resistor to a load capacitor. At a minimum the entire circuit, including the source impedance for the signal driving the analog input should be designed to settle to within ¼ LSB within the sampling window to match the performance of the ADC. 8.8 System Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 13 System Characteristics Parameter Conditions Min Doze to Active state delay Doze to Radio TX or RX QCCA charge to sample RF channel Start from Doze state Radio baud rate RESETn pulse width 20 125 Linear Technology / Dust Networks Typ Max Units 5 µs 1.2 ms 4 µC 250 kbps µs Eterna Datasheet Advanced Information 8.9 UART AC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 14 UART Timing Values Parameter Conditions Min Typ Max Unit tRX_BAUD Deviation from baud rate –2 +2 % tTX_BAUD Deviation from baud rate –1 +1 % tRX_RTS_R to RX_CTS Assertion of UART_RX_RTSn to assertion of UART_RX_CTSn, or negation of UART_RX_RTSn to negation of UART_RX_CTSn 0 22 ms tCTS_R to RX Assertion of UART_RX_CTSn to start of byte 0 20 ms tEOP to RX_RTS End of packet (end of the last stop bit) to negation of UART_RX_RTSn 0 22 ms tTX_RTS_T to TX_CTS Assertion of UART_TX_RTSn to assertion of UART_TX_CTSn, or negation of UART_TX_RTSn to negation of UART_TX_CTSn 0 22 ms tTX_CTS_T to TX Assertion of UART_TX_CTSn to start of byte 0 2 bit period tEOP to TX_RTS End of packet (end of the last stop bit) to negation of UART_TX_RTSn 0 1 bit period tRX_INTERBYTE Receive Inter-byte delay 100 ms tTX to TX_CTS Start of byte to negation of UART_TX_CTSn tINTERPACKET Transmit and Receive Inter-packet delay (Mode 4 only) 0 ms 100 ms Figure 16 UART Timing Eterna Datasheet Linear Technology / Dust Networks 21 Advanced Information 8.10 TIMEn AC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Note that the time pin must remain negated until the time packet has been received. Table 15 Timestamp Characteristics Parameter Conditions tstrobe Min Typ Max 125 Unit µs tresponse From rising edge of TIMEn Resolution See the serial API definition for getParameter<time> +/- 1 100 ms µs Network-wide time accuracy Stable temperature environment +/- 50 µs Figure 17 Timestamp Timing Diagram 8.11 SLEEPn AC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Note that the time pin must remain negated until the time packet has been received. Table 16 SLEEPn Characteristics Parameter Conditions Min Typ Max Unit tdoze From falling edge of SLEEPn 20 ms Tsleep_strobe Maximum strobe width 2 s Figure 18 SLEEPn Timing Diagram 8.12 RADIO_INHIBIT AC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Note that the time pin must remain negated until the time packet has been received. Table 17 RADIO_INHIBIT Characteristics Max Unit tradio_off Parameter From rising edge of RADIO_INHIBIT 20 ms Tradio_inhibit_strobe Maximum strobe width 2 s 22 Conditions Linear Technology / Dust Networks Min Typ Eterna Datasheet Advanced Information Figure 19 RADIO_INHIBIT Timing Diagram 8.13 FLASH AC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C, unless otherwise specified. Table 18 FLASH AC Timing Values Parameter Conditions Min Typ Max Unit t32-BIT_WORD Writing a 32-bit word 21 µs tPAGE_ERASE Page Erase 21 ms tMASS_ERASE Bank Erase 21 ms 8.14 Flash Programming AC Characteristics The following characteristics are measured with VSUPPLY = 3.6 V at 25 °C with 10 pF load capacitance, unless otherwise specified. Table 19 SPI Slave AC Timing Values Parameter Conditions Min Typ Max Unit tSSS IPCS_SSn setup to leading edge of IPCS_SCK 15 ns tSSH IPCS_SSn hold from trailing edge of IPCS_SCK 15 ns tCK IPCS_SCK period 50 ns tDIS IPCS_MOSI data setup 15 ns tDIH IPCS_MOSI data hold 5 ns tDOV IPCS_MISO data valid 3 15 ns tOFF IPCS_MISO data tri-state 0 15 ns Figure 20 Flash Programming Slave Timing Eterna Datasheet Linear Technology / Dust Networks 23 Advanced Information 9.0 Typical Performance Characteristics Network motes typically route through at least two parents traffic destined for the manager. The bandwidth and keep-alive overhead required to support network motes will be shared across all of the mote's parents. The supply current plots include a parameter called traffic-weighted descendants. In these graphs the term traffic-weighted descendants refers to an amount of activity equivalent to the number of descendants were all of the network traffic and keep-alives directed to the mote in question. Generally the number of descendants of a parent is more (typically 2x or more) than the number of traffic-weighted descendants. For example, with reference to Figure 25 mote P1 has 0.75 traffic-weighted descendants. To obtain this value notice that mote D1 routes half its packets through mote P1 adding 0.5 to the traffic-weighted descendant value; the other half of D1's traffic is routed through its other parent, P2. Mote D2 routes half its packets through mote D1 (the other half going through parent P3), which we know routes half its packets to mote P1, adding another 0.25 to the traffic-weighted descendant value for a total traffic-weighted descendant value of 0.75. Figure 25 Network Graph Depicting Traffic Weighted Descendant Value Calculation The following plots correspond to networks with a P2 bandwidth profile, an assumed path stability of 80%, an 80 byte packet and unless otherwise specified operation at 25 degrees C. 24 Linear Technology / Dust Networks Eterna Datasheet Advanced Information 10.0 Mechanical Details 10.2 Mote Module The Eterna mote modules comes in 66-lead, 1 mm lead pitch castellated PCB, as illustrated in Figure 27 and in Figure 28. Figure 27 Mechanical Drawing – LTP5901 Eterna Datasheet Linear Technology / Dust Networks 25 Advanced Information Figure 28 Mechanical Drawing – LTP5902 26 Linear Technology / Dust Networks Eterna Datasheet Advanced Information 10.3 Soldering Information Eterna is suitable for both eutectic PbSn and RoHS-6 reflow. The maximum reflow soldering temperature is 260 ºC. Regulatory and Standards Compliance 11.0 LTP5901 is compliant with EU, FCC and IC radio frequency regulations. For specific information on regulations, test procedures, and labeling requirements, see the “LTP5901 Regulatory User Guide”. LTP5902 is compliant with EU, FCC and IC radio frequency regulations. For specific information on regulations, test procedures, and labeling requirements, see the “LTP5902 Regulatory User Guide”. 11.1 Compliance to Restriction of Hazardous Substances (RoHS) Restriction of Hazardous Substances (RoHS) is a directive that places maximum concentration limits on the use of cadmium (Cd), lead (Pb), hexavalent chromium (Cr+6), mercury (Hg), Polybrominated Biphenyl (PBB), and Polybrominated Diphenyl Ethers (PBDE). Dust Networks is committed to meeting the requirements of the European Community directive 2002/95/EC. This product has been specifically designed to utilize RoHS-compliant materials and to eliminate or reduce the use of restricted materials to comply with 2002/95/EC. The RoHS-compliant design features include: • RoHS-compliant solder for solder joints • RoHS-compliant base metal alloys • RoHS-compliant precious metal plating • RoHS-compliant cable assemblies and connector choices • Lead-free QFN package • Halogen-free mold compound • RoHS-compliant and 245 °C re-flow compatible Note: Customers may elect to use certain types of lead-free solder alloys in accordance with the European Community directive 2002/95/EC. Depending on the type of solder paste chosen, a corresponding process change to optimize reflow temperatures may be required. References 12.0 [1] IEEE Std. 802.15.4-2006: Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) http://standards.ieee.org/getieee802/download/802.15.4-2006.pdf 13.0 Order Information LEAD FREE FINISH** PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTP5901IPC-WHMA???#PBF LTP5901 66-Lead (42mm x 24mm) PCB -40 °C to 85 °C LTP5902IPC-WHMA???#PBF LTP5902 66-Lead (37.465mm x 24mm) PCB -40 °C to 85 °C ** See http://www.linear.com/ or contact your sales representative to determine the three digit software version field, ???. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ Eterna Datasheet Linear Technology / Dust Networks 27 Advanced Information Trademarks SmartMesh Industrial and Eterna are trademarks of Dust Networks, Inc. The Dust Networks logo, Dust, Dust Networks, and SmartMesh are registered trademarks of Dust Networks, Inc. The Linear logo is a registered trademark of Linear Technology Corporation. All third-party brand and product names are the trademarks of their respective owners and are used solely for informational purposes. ARM and Cortex are trademarks or registered trademarks of ARM Limited in the EU and other countries. Copyright This documentation is protected by United States and international copyright and other intellectual and industrial property laws. It is solely owned by Dust Networks, Inc. and its licensors and is distributed under a restrictive license. This product, or any portion thereof, may not be used, copied, modified, reverse assembled, reverse compiled, reverse engineered, distributed, or redistributed in any form by any means without the prior written authorization of Dust Networks, Inc. RESTRICTED RIGHTS: Use, duplication, or disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g) (2)(6/87) and FAR 52.227-19(6/87), or DFAR 252.227-7015 (b)(6/95) and DFAR 227.7202-3(a), and any and all similar and successor legislation and regulation. Disclaimer This documentation is provided “as is” without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or fitness for a particular purpose. This documentation might include technical inaccuracies or other errors. Corrections and improvements might be incorporated in new versions of the documentation. Dust Networks does not assume any liability arising out of the application or use of any products or services and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Dust Networks products are not designed for use in life support appliances, devices, or other systems where malfunction can reasonably be expected to result in significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Dust Networks customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify and hold Dust Networks and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Dust Networks was negligent regarding the design or manufacture of its products. Dust Networks reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products or services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to Dust Network's terms and conditions of sale supplied at the time of order acknowledgment or sale. Dust Networks does not warrant or represent that any license, either express or implied, is granted under any Dust Networks patent right, copyright, mask work right, or other Dust Networks intellectual property right relating to any combination, machine, or process in which Dust Networks products or services are used. Information published by Dust Networks regarding third-party products or services does not constitute a license from Dust Networks to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from Dust Networks under the patents or other intellectual property of Dust Networks. Dust Networks, Inc is a wholly owned subsidiary of Linear Technology Corporation. © Dust Networks, Inc. 2012. All Rights Reserved. 28 Linear Technology / Dust Networks Eterna Datasheet Advanced Information Last Revised: Document Status March 15, 2013 Product Status Definition Advanced Information Planned or under development This datasheet contains the design specifications for product development. Dust Networks reserves the right to change specifications in any manner without notice. Preliminary Engineering samples and pre-production prototypes This datasheet contains preliminary data; supplementary data will be published at a later time. Dust Networks reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. The product is not fully qualified at this point. No Identification Noted Full production This datasheet contains the final specifications. Dust Networks reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Obsolete Not in production This datasheet contains specifications for a product that has been discontinued by Dust Networks. The datasheet is printed for reference information only. Eterna Datasheet Linear Technology / Dust Networks 29