TECHNICAL DATA IN74AC112 Dual J-K Flip-Flop with Set and Reset High-Speed Silicon-Gate CMOS The IN74AC112 is identical in pinout to the LS/ALS112, HC/HCT112. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALS outputs. Each flip-flop is negative-edge clocked and has active-low asynchronous Set and Reset inputs. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA; 0.1 µA @ 25°C • High Noise Immunity Characteristic of CMOS Devices • Outputs Source/Sink 24 mA ORDERING INFORMATION IN74AC112N Plastic IN74AC112D SOIC TA = -40° to 85° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs PIN 16=VCC PIN 8 = GND Outputs Set Reset Clock J K Q Q L H X X X H L H L X X X L H X X * L L* L L X H H L L No Change H H L H L H H H H L H L H H H H Toggle H H L X X No Change H H H X X No Change H H X X No Change * Both outputs will remain low as long as Set and Reset are low, but the output states are unpredictable if Set and Reset go high simultaneously X = Don’t Care 127 IN74AC112 MAXIMUM RATINGS* Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin ±20 mA IOUT DC Output Sink/Source Current, per Pin ±50 mA ICC DC Supply Current, VCC and GND Pins ±50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 °C 260 °C VOUT IIN Tstg TL Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TJ Junction Temperature (PDIP) TA Operating Temperature, All Package Types IOH Output Current - High IOL Output Current - Low tr, tf * Parameter Input Rise and Fall Time (except Schmitt Inputs) * Min Max Unit 2.0 6.0 V 0 VCC V 140 °C +85 °C -24 mA 24 mA 150 40 25 ns/V -40 VCC =3.0 V VCC =4.5 V VCC =5.5 V 0 0 0 VIN from 30% to 70% VCC This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 128 IN74AC112 DC ELECTRICAL CHARACTERISTICS(Voltages Referenced to GND) VCC Guaranteed Limits V 25 °C -40°C to 85°C Unit VOUT=0.1 V or VCC-0.1 V 3.0 4.5 5.5 2.1 3.15 3.85 2.1 3.15 3.85 V Maximum Low Level Input Voltage VOUT=0.1 V or VCC-0.1 V 3.0 4.5 5.5 0.9 1.35 1.65 0.9 1.35 1.65 V Minimum High-Level Output Voltage IOUT ≤ -50 µA 3.0 4.5 5.5 2.9 4.4 5.4 2.9 4.4 5.4 V 3.0 4.5 5.5 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.1 0.1 0.1 0.1 0.1 0.1 VIN=VIH or VIL IOL=12 mA IOL=24 mA IOL=24 mA 3.0 4.5 5.5 0.36 0.36 0.36 0.44 0.44 0.44 Maximum Input Leakage Current VIN=VCC or GND 5.5 ±0.1 ±1.0 µA IOLD +Minimum Dynamic Output Current VOLD=1.65 V Max 5.5 75 mA IOHD +Minimum Dynamic Output Current VOHD=3.85 V Min 5.5 -75 mA ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND 5.5 40 µA Symbol Parameter VIH Minimum High-Level Input Voltage VIL VOH Test Conditions * VIN=VIH or VIL IOH=-12 mA IOH=-24 mA IOH=-24 mA VOL Maximum Low-Level Output Voltage IOUT ≤ 50 µA V * IIN 4.0 * All outputs loaded; thresholds on input associated with output under test. +Maximum test duration 2.0 ms, one output loaded at a time. Note: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC 129 IN74AC112 AC ELECTRICAL CHARACTERISTICS(CL=50pF,Input tr=tf=3.0 ns) VCC* Symbol Parameter Guaranteed Limits 25 °C V Min -40°C to 85°C Max Min Unit Max fmax Maximum Clock Frequency (Figure 1) 3.3 5.0 145 145 125 125 tPLH Propagation Delay, Clock to Q or Q (Figure 1) 3.3 5.0 1.0 1.0 16.0 13.0 1.0 1.0 17.0 13.5 ns tPHL Propagation Delay, Clock to Q or Q (Figure 1) 3.3 5.0 1.0 1.0 16.0 13.0 1.0 1.0 16.5 13.5 ns tPLH Propagation Delay, Set or Reset to Q or Q (Figure 2) 3.3 5.0 1.0 1.0 11.0 9.5 1.0 1.0 11.5 10.0 ns tPHL Propagation Delay, Set or Reset to Q or Q (Figure 2) 3.3 5.0 1.0 1.0 11.0 9.5 1.0 1.0 11.5 10.0 ns CIN Maximum Input Capacitance 5.0 4.5 MHz 4.5 pF Typical @25°C,VCC=5.0 V CPD Power Dissipation Capacitance 35 pF Voltage Range 3.3 V is 3.3 V ±0.3 V Voltage Range 5.0 V is 5.0 V ±0.5 V * TIMING REQUIREMENTS(CL=50pF,Input tr=tf=3.0 ns) VCC* Guaranteed Limits Symbol Parameter V 25 °C -40°C to 85°C Unit tsu Minimum Setup Time, J or K to Clock (Figure 3) 3.3 5.0 6.5 4.5 7.5 5.0 ns th Minimum Hold Time, Clock to J or K (Figure 3) 3.3 5.0 0 0 0 0 ns tw Minimum Pulse Width, Clock (Figure 1) 3.3 5.0 6.0 5.0 6.5 5.5 ns tw Minimum Pulse Width,Set or Reset (Figure 2) 3.3 5.0 6.5 5.0 7.5 5.5 ns trec Minimum Recovery Time, Set or Reset to Clock (Figure 2) 3.3 5.0 0 0 0 0 ns Voltage Range 3.3 V is 3.3 V ±0.3 V Voltage Range 5.0 V is 5.0 V ±0.5 V * 130 IN74AC112 Figure 1. Switching Waveform Figure 2. Switching Waveform Figure 3. Switching Waveform EXPANDED LOGIC DIAGRAM 131