MB2S-MB10S Single Phase 0.8AMP. Glass Passivated Bridge Rectifiers MBS .193(4.90) .177(4.50) .033(0.84) Features .022(0.56) .157(4.00) .142(3.60) Ideal for printed circuit board Reliable low cost construction utilizing molded plastic technique High surge current capability High temperature soldering guaranteed: o 260 C / 10 seconds at 5 lbs., (2.3 kg ) tension Small size, simple installation .272(6.9) MAX .102(2.60) .087(2.20) .106(2.70) .053(1.53) .014(0.35 .090(2.30) .037(0.95) .006(0.15 .008(0.20) .114(2.9) .043(1.10) .083(2.12) MAX MAX .028(0.70) .043(1.10) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol MB2S VRRM 200 VRMS 140 VDC 200 Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current On glass-epoxy P.C.B. On aluminum substrate Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 0.4A MB4S MB6S MB8S 400 280 400 600 420 600 800 560 800 Typical Junction Capacitance Per Leg Typical Thermal Resistance Per Leg Operating Temperature Range Storage Temperature Range 1000 700 1000 0.5 0.8 A IFSM 35 A VF 1.0 V 5.0 100 13 85 -55 to +150 -55 to +150 uA uA pF o C/W o C o C IR Cj RθJA TJ TSTG Note: 1. Measured at 1.0MHz and Applied Reverse Voltage of 4.0 Volts D.C. http://www.luguang.cn V V V I(AV) o Maximum DC Reverse Current @ TA=25 C at Rated DC Blocking Voltage @ TA=125 oC MB10S Units mail:[email protected] MB2S-MB10S Single Phase 0.8AMP. Glass Passivated Bridge Rectifiers RATINGS AND CHARACTERISTIC CURVES FIG.1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.2- TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG INSTANTANEOUS REVERSE LEAKAGE CURRENT. (mA) AVERAGE FORWARD RECTIFIED CURRENT. (A) 0.8 Aluminum Substrate 0.7 0.6 0.5 Glass Epoxy P.C.B 0.4 0.3 0.2 Resistive or Inductive Load 0.1 0 0 20 40 80 60 100 120 O AMBIENT TEMPERATURE. ( C) 140 100 Tj=125 0C 10 1 0.1 Tj=25 0C 0.01 160 0 FIG.3-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 80 20 40 60 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 100 FIG.4- TYPICAL JUNCTION CAPACTITANCE PER LEG 30 35 JUNCTION CAPACITANCE (pF) PEAK FORWARD SURGE CURRENT. (A) O Tj=40 C Single Half Sine-Wave (JEDEC Method) 30 25 F=60 Hz F=50 Hz 20 15 Tj=25 C 25 f = 1 MHz Vsig = 50mVp-p 20 15 10 5 10 0 0.1 1 Cycle 5 1 10 REVERSE VOLTAGE. (V) 0 10 NUMBER OF CYCLES 1 100 FIG.5- TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT. (A) 10 1 Tj=25 0C 0.1 Tj=25 C Pulse Width=300ms 1% Duty Cycle 0.01 0.2 0.4 0.6 0.8 1.0 1.2 INSTANTANEOUS FORWARD VOLTAGE. (V) http://www.luguang.cn 1.4 mail:[email protected] 100 200