LCD15 LCD15 SERIES DC-DC CONVERTER 2:1 WIDE INPUT RANGE UP TO 15Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • 1600VDC INPUT TO OUTPUT ISOLATION • SMALL SIZE AND LOW PROFILE 1.0 x 1.0 x 0.39 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT ： 1600VDC ISOLATION REMOTE CONTROL UVP OCP SCP OVP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted Model Number Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 mA 4000 3000 1300 1000 ±1500 ±625 ±500 4000 3000 1300 1000 ±1500 ±625 ±500 4000 3000 1300 1000 ±1500 ±625 ±500 mA 120 90 30 30 30 30 30 50 65 20 20 15 15 25 25 35 12 12 12 15 20 % 84 88 86 88 85 87 88 86 88 87 88 85 88 88 86 88 88 88 85 89 88 µF 12000 6000 1000 660 ±3000 ±520 ±330 12000 6000 1000 660 ±3000 ±520 ±330 12000 6000 1000 660 ±3000 ±520 ±330 LCD15-12S3P3 LCD15-12S05 LCD15-12S12 LCD15-12S15 LCD15-12D05 LCD15-12D12 LCD15-12D15 LCD15-24S3P3 LCD15-24S05 LCD15-24S12 LCD15-24S15 LCD15-24D05 LCD15-24D12 LCD15-24D15 LCD15-48S3P3 LCD15-48S05 LCD15-48S12 LCD15-48S15 LCD15-48D05 LCD15-48D12 LCD15-48D15 PART NUMBER STRUCTURE LCD15 - 48 Series Name Input Voltage (VDC) 12: 9~18 24: 18~36 48: 36~75 S Output Quantity S: Single D: Dual 1 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 05: ±5 12: ±12 15: ±15 : A: B: C: D: E: A HS Option Assembly Option Negative logic remote ON/OFF(Standard) Positive logic remote ON/OFF Without Ctrl pin Negative logic remote ON/OFF without Trim pin Without Ctrl & Trim pin Positive logic remote ON/OFF without Trim pin www.PDUKE.com : No Assembly Option HS: Heat-sink HC: Heat-sink & Clamp 2014/04/30 LCD15 INPUT SPECIFICATIONS Parameter Conditions Operating input voltage range Input reflected ripple current Start-up voltage 12Vin(nom) 24Vin(nom) 48Vin(nom) Start up time Constant resistive load Input surge voltage 100ms, max. Positive logic DC-DC ON (Option) DC-DC OFF Negative logic DC-DC ON (Standard) DC-DC OFF Input current of Ctrl pin Remote off input current Conditions -0.5 Min. Load regulation No Load to Full Load Cross regulation Voltage adjustability (2) Ripple and noise Asymmetrical load 25%/100% FL Single output Measured by 20MHz bandwidth; With a 1µF M/C X7R and a 10µF T/C Single 3.3Vout, 5Vout Others Dual All Single Dual Single Dual Dual Typ. % of Iout rated; Hiccup mode Isolation resistance Isolation capacitance Switching frequency Safety approvals 500VDC VDC VDC mA mA Unit +1.0 +0.2 +0.5 +0.2 +1.0 +5.0 +10 % % % % % mVp-p +0.02 3.7 5.6 13.5 16.8 ms Max. 250 3.3Vout 5Vout 12Vout 15Vout 1 minute VDC 75 100 100 -0.02 Isolation voltage mAp-p 30 30 36 50 100 Pi type Open or 3 ~ 15VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 15VDC 1.0 2.5 -1.0 -0.2 -0.5 -0.2 -1.0 -5.0 -10 25% load step change GENERAL SPECIFICATIONS Parameter 2 VDC 8 14.5 30.5 Low Line to High Line at Full Load Case material Base material Potting material Weight MTBF Unit 18 36 75 9 18 36 Voltage accuracy Line regulation Over load protection Short circuit protection Max. 12 24 48 30 12Vin(nom) 24Vin(nom) 48Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 12Vin(nom) 24Vin(nom) 48Vin(nom) Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter Temperature coefficient Transient response recovery time Over voltage protection Typ. 9 18 36 Nominal input and Full load Shutdown voltage Input filter Remote ON/OFF Min. 5.4 7.0 19.6 20.5 ℃ %/ µs VDC 150 % Continuous, automatics recovery Conditions Input to Output Input(Output) to Case Min. 1600 1000 1 360 MIL-HDBK-217F, Full load www.PDUKE.com Typ. Max. Unit VDC GΩ pF 400 kHz UL60950-1 EN60950-1 IEC60950-1 Nickel-coated copper FR4 PCB Epoxy (UL94 V-0) 15g (0.53oz) 1.600 x 106 hrs 1000 440 2014/04/30 LCD15 ENVIRONMENTAL SPECIFICATIONS Parameter Conditions Operating ambient temperature Maximum case temperature Storage temperature range Thermal impedance Min. Without derating With derating Typ. Max. -40 +60 +60 +105 105 +125 -55 Vertical direction by natural convection (20LFM) Without heat-sink With heat-sink 18.2 15.8 Thermal shock Vibration Relative humidity Unit ℃ ℃ ℃ ℃/W MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (3) ESD Radiated immunity Fast transient (4) Surge (4) Conducted immunity Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 1kV 3 Vr.m.s Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: 1. 2. 3. 4. Test by minimum input and constant resistive load. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor between the Trim pin and either +Vout pin or -Vout pin. The standard modules meet EN55022 Class A and Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE 3 LCD15-48S05 Derating Curve LCD15-48S05 Derating Curve With Heat-sink LCD15-48S05 Efficiency vs. Input Voltage LCD15-48S05 Efficiency vs. Output Load www.PDUKE.com 2014/04/30 LCD15 MECHANICAL DRAWING PIN CONNECTION PIN 1 2 3 4 5 6 SINGLE +Vin -Vin Ctrl +Vout Trim -Vout DUAL +Vin -Vin Ctrl +Vout Common -Vout EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 6 5 RU 5 RD 4 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2014/04/30